MC93XX
Mobile Computer
Quick Start Guide
MN-003413-01 Rev. A
MC93XX Quick Start Guide
Copyright
ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corporation, registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners. ©2019 Zebra
Technologies Corporation and/or its affiliates. All rights reserved.
COPYRIGHTS & TRADEMARKS: For complete copyright and trademark information, go to www.zebra.com/copyright .
WARRANTY: For complete warranty information, go to www.zebra.com/warranty .
END USER LICENSE AGREEMENT: For complete EULA information, go to www.zebra.com/eula .
Terms of Use
• Proprietary Statement
This manual contains proprietary information of Zebra Technologies Corporation and its subsidiaries (“Zebra
Technologies”). It is intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the express, written permission of Zebra Technologies.
• Product Improvements
Continuous improvement of products is a policy of Zebra Technologies. All specifications and designs are subject to change without notice.
• Liability Disclaimer
Zebra Technologies takes steps to ensure that its published Engineering specifications and manuals are correct; however, errors do occur. Zebra Technologies reserves the right to correct any such errors and disclaims liability resulting therefrom.
• Limitation of Liability
In no event shall Zebra Technologies or anyone else involved in the creation, production, or delivery of the accompanying product (including hardware and software) be liable for any damages whatsoever (including, without limitation, consequential damages including loss of business profits, business interruption, or loss of business information) arising out of the use of, the results of use of, or inability to use such product, even if
Zebra Technologies has been advised of the possibility of such damages. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Warranty
For the complete Zebra hardware product warranty statement, go to www.zebra.com/warranty .
Service Information
Before you use the unit, it must be configured to operate in your facility’s network and run your applications.
If you have a problem running your unit or using your equipment, contact your facility’s Technical or Systems
Support. If there is a problem with the equipment, they will contact the Zebra Global Customer Support at www.zebra.com/support .
For the latest version of this guide go to www.zebra.com/support .
2
MC93XX Quick Start Guide
Provide Documentation Feedback
If you have comments, questions, or suggestions about this guide, send an email to [email protected]
.
Configurations
MC93XX used in this guide refers to the MC93XX-G mobile computer with scan trigger. This guide applies to the following Model Numbers: MC930B, MC930P.
Unpacking
Carefully remove all protective material from the device and save the shipping container for later storage and shipping.
Verify the following items are in the box:
• Device
• Lithium-ion battery
• Regulatory Guide.
Inspect the equipment for damage. If any equipment is missing or damaged, contact the Zebra Support Center immediately.
3
Device Features
Figure 1 MC93XX Front View
1
2
MC93XX Quick Start Guide
13
12
11
10
3
4
5
6
7
9
8
Table 1 MC93XX Features - Front View
1
2
Number Item
Ambient Light
Sensor
Front Facing
Camera
Use to take photos and videos.
Function
Controls display and keyboard backlight.
3
4
NOTE : The front camera is available only on the premium configurations.
Displays all information needed to operate the device.
Provides audio output for video and music playback.
5
6
7
Display
Speaker Side
Port
Trigger
P1 - Dedicated
PTT Key
Battery Release
Latch
Initiates data capture when a scan application is enabled.
Initiates push-to-talk communications (programmable).
Releases the battery from the device.
NOTE : To release the battery, simultaneously press the battery release latches on both the sides of the device.
4
MC93XX Quick Start Guide
Table 1 MC93XX Features - Front View (continued)
8
9
10
11
Number
12
Battery
Item
Microphone
Keypad
Power Button
Function
Provides power for operating the device.
Use for communications in Handset mode.
Use to enter data and navigate on screen functions.
Press and hold to turn on the device. Press to turn on or off the screen.
Press and hold to select one of these options:
Power off - Turn off the device.
Restart - Restart the device when software stops responding.
Initiates data capture when a scan application is enabled.
13
Center Scan
Button
Charger/Decode
Status LED
Indicates battery charging status while charging, app generated notifications, and data capture status.
Figure 2 MC93XX Back View
14
15
16
17
18
19
20
5
MC93XX Quick Start Guide
Table 2 MC93XX Features - Back View
14
Number
15
16
17
18
Item
Passive NFC Tag
(Under the battery compartment.)
Battery Release
Latch
Function
Provides secondary product label information (configuration, serial number and manufacture data code) in the event that the readable product label is worn or missing.
Releases the battery from the device.
Side Speaker Port Provides audio output for video and music playback.
Scanner Exit
Window
Provides data capture using the scanner/imager.
Camera Flash Provides illumination for the camera.
19
20
NFC Antenna
Rear Camera
NOTE : Camera is available only on some configurations.
Provides communication with other NFC-enabled devices.
NOTE : NFC antenna is available only on the premium configurations.
Takes photos and videos.
NOTE : The rear camera is available only on the premium configurations.
Setup
To start using the device for the first time:
• Install a microSD card (optional)
• Install the battery
• Charge the device
• Power on the device.
Installing a microSD Card
The microSD card slot provides secondary non-volatile storage. The slot is located under the keypad module.
Refer to the documentation provided with the card for more information, and follow the manufacturer’s recommendations for use. It is strongly recommended that prior to use, you must format the microSD card on the device.
CAUTION : Follow proper electrostatic discharge (ESD) precautions to avoid damaging the microSD card. Proper ESD precau tions include, but are not limited to, working on an ESD mat and ensuring that the operator is properly grounded.
-
1. Power off the device.
2. Remove the battery.
6
MC93XX Quick Start Guide
3. Using a Torx T8 screwdriver with a large grip, remove the two keypad latch screws from inside the battery slot.
Figure 3 Remove Keypad Latch Screws
Keypad Latch Screws
4. Slide the keypad latches toward the bottom of the device.
Figure 4 Release Keypad Latches
Screwdriver
Keypad Latches
NOTE : If the keypad latches are hard to move, use a screwdriver to gently slide them towards the bottom of the device.
5. Turn the device over so that the keypad is visible.
7
MC93XX Quick Start Guide
6. Using a Torx T8 screwdriver with a large grip, remove the two keypad assembly screws from the top of the keypad.
Figure 5 Remove Keypad
Keypad Screws
Keypad microSD Card Holder
7. Lift the keypad from the device.
8. Slide the microSD card holder to the Open position.
Figure 6 Open microSD Card Holder
8
9. Lift the microSD card holder.
Figure 7 Lift microSD Card Holder
MC93XX Quick Start Guide
10.Insert the microSD card into the card holder door ensuring that the card slides into the holding tabs on each side of the door.
Figure 8 Insert microSD Card into Holder
11.Close the microSD card holder door and slide the door to the Lock position.
Figure 9 Close and Lock microSD Card in Holder
9
MC93XX Quick Start Guide
12.Align the keypad along the bottom ridge of the device, and then lay it flat.
Figure 10 Replace Keypad
13.Using a Torx T8 screwdriver with a large grip and a long shaft, secure the keypad to the device using the two screws. Torque screws to 5.8 kgf-cm or 5.0 lbf-in.
Figure 11 Replace Keypad Screws
Keypad Screws
14.Turn the device over so that the keypad latches are visible.
10
MC93XX Quick Start Guide
15.Slide both the keypad latches toward the top of the device.
Figure 12 Slide Keypad Latches
Keypad Latches
16.Using a Torx T8 screwdriver, replace the two keypad latch screws inside the battery slot and torque to 5.8 kgf-cm or 5.0 lbf-in.
Figure 13 Replace Keypad Latch Screws
Keypad Latch Screws
17.Press and hold the Power key to power on the device.
Installing the Battery
The MC93XX is compatible with the following battery:
• 7000 mAh PowerPrecision+ standard battery
To install the battery:
11
MC93XX Quick Start Guide
1. Align the battery with the battery slot.
Figure 14 Inserting the Battery
2. Push the battery into the battery slot.
3. Press battery firmly into the battery well. Ensure that both the battery release buttons on the sides of the device return to the home position. You will hear an audible click sound indicating that both the battery release buttons on the sides of the device have returned to the home position locking the battery in place.
Figure 15 Press Battery In
4. Press the Power button to turn on the device.
12
MC93XX Quick Start Guide
Charging the Device
Use one of the following accessories to charge the battery .
Table 3 Charging and Communication
Description Part Number
Charging
Battery
(In
Device)
Yes
Spare
Battery
Yes
Communication
USB
Yes 1-Slot USB Charge Cradle with
Spare Battery Charger
4-Slot Charge Only ShareCradle
4-Slot Spare Battery Charger
16-Slot Spare Battery Charger
USB Charge/Com Snap-on Cup
NOTE : A separate USB cable and pow er supply is required to support fast charging. USB (Type-C) Cable is re quired to allow communication from the snap-on to the PC/laptop.
-
Charge Only Adapter
CRD-MC93-2SUCHG-01
CRD-MC93-4SCHG-01
SAC-MC93-4SCHG-01
SAC-MC93-16SCHG-01
CBL-MC93-USBCHG-01
ADP-MC93-CRDCUP-01
Yes
No
No
Yes
No
Yes
Yes
No
No
No
No
Yes
Yes NA No
Charging the Main Battery
To charge the main battery:
1. Connect the charging accessory to the appropriate power source.
2. Insert the device into a cradle or attach a cable.
The device starts to charge automatically. The Charge LED Indicator indicates the charge status. See the table below for charging indications.
Table 4 LED Charge Indicators
Status
Off
Slow Blinking Amber
Every 3 seconds
Indications
• The battery is not charging.
• The device is not inserted correctly in the cradle or connected to a power source.
• Cradle is not powered.
• Battery is charging, but the battery is fully depleted and does not yet have sufficient charge to power the device.
• After battery removal, indicates that the device is in hot swap mode with connectivity persistence.
Solid Amber
NOTE : The SuperCap requires a minimum of 15 minutes to fully charge in order to provide adequate connectivity and memory session persistence.
• Battery is charging.
13
MC93XX Quick Start Guide
Table 4 LED Charge Indicators (continued)
Solid Green
Status
Fast Blinking Red
2 blinks/second
Solid Red
Indications
• Battery charging is complete.
Charging error. For example:
• Temperature is too low or too high.
• Charging has gone on too long without completion (typically eight hours).
• Battery is charging and battery is at the end of useful life.
• Charging complete and battery is at the end of useful life.
The 7000 mAh PowerPrecision+ standard battery charges from 0% to 90% in less than 3.5 hours at room temperature using a Zebra accessory.
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The device or cradle always performs battery charging in a safe and intelligent manner. At higher temperatures, for example at approximately +37°C (+98°F), the device or cradle may for small periods of time alternately enable and disable battery charging to keep the battery at acceptable temperatures. The device and cradle indicates when charging is disabled due to abnormal temperatures via its LED.
Charging the Spare Battery
1. Ensure that the cradle is connected to power.
2. Insert the spare battery into the charging well, small end first, onto the contact pins.
14
MC93XX Quick Start Guide
Figure 16 Charging the Spare Battery
Spare Battery
Spare Battery Charging Well
Spare Battery Charging LED
3. Gently press down on the battery to ensure proper contact.
The 1-Slot USB charge cradle charges the MC93XX’s main battery and a spare battery simultaneously.
The MC93XX’s Charge LED indicates the status of the battery charging in the device. See LED Charge Indicators for charging status indications.
Table 5 LED Charge Indicators
Status
Off
Slow Blinking Amber
Every 3 seconds
Solid Amber
Indications
• The battery is not charging.
• The device is not inserted correctly in the cradle or connected to a power source.
• Cradle is not powered.
• Battery is charging, but the battery is fully depleted and does not yet have sufficient charge to power the device.
• Battery is charging.
15
MC93XX Quick Start Guide
Table 5 LED Charge Indicators (continued)
Solid Green
Status
Fast Blinking Red
2 blinks/second
Solid Red
Indications
• Battery charging is complete.
Charging error. For example:
• Temperature is too low or too high.
• Charging has gone on too long without completion (typically eight hours).
• Battery is charging and battery is at the end of useful life.
• Charging complete and battery is at the end of useful life.
The 7,000 mAh PowerPrecision+ standard battery charges from 0% to 90% in less than 3.5 hours at room temperature using a Zebra accessory.
The Spare Battery Charging LEDs on the front of the cradle indicates the spare battery charging status. The following table specifies charging indicators.
Table 6 Charging/Notification LED Charging Indicators
Off
State
Solid Amber
Solid Green
Fast Blinking Red
2 blinks/second
Solid Red
Indication
• The battery is not charging.
• The battery is not inserted correctly in the cradle.
• Cradle is not powered.
• Battery is charging.
• Battery charging is complete.
Charging error. For example:
• Temperature is too low or too high.
• Charging has gone on too long without completion (typically eight hours).
• Battery is charging and battery is at the end of useful life.
• Charging complete and battery is at the end of useful life.
When charging is complete, lift the battery out of the slot.
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The device or cradle always performs battery charging in a safe and intelligent manner. At higher temperatures, for example at approximately +37°C (+98°F), the device or cradle may for small periods of time alternately enable and disable battery charging to keep the battery at acceptable temperatures. The device and cradle indicates when charging is disabled due to abnormal temperatures via its LED.
1-Slot USB Charge Cradle with Spare Battery Charger
The 1-Slot USB Charge Cradle with spare battery:
• Provides 9 VDC power to operate the mobile computer and charge the battery.
• Provides 4.2 VDC power to charge the spare battery.
• Provides a USB port for data communication between the mobile computer and a host computer or other USB devices, for example, a printer.
16
MC93XX Quick Start Guide
• Synchronizes information between the mobile computer and a host computer. With customized or third party software, it can also synchronize the mobile computer with corporate databases.
• Compatible with the following battery:
• 7000 mAh PowerPrecision+ standard battery
Figure 17 1-Slot USB Charge Cradle with Spare Battery Charger
Indicator LED Bar
Spare Battery
Spare Battery Charging Well
Spare Battery Charging LED
17
MC93XX Quick Start Guide
4-Slot Charge Only ShareCradle
The 4-Slot Charge Only ShareCradle:
• Provides 9 VDC power to operating the mobile computer and charge the battery.
• Simultaneously charges up to four mobile computers.
• Compatible with devices using the following battery:
• 7000 mAh PowerPrecision+ standard battery
Figure 18 4-Slot Charge Only ShareCradle
Power LED
18
MC93XX Quick Start Guide
4-Slot Spare Battery Charger
The 4-Slot Spare Battery Charger:
• Charges up to four spare batteries.
• Provides 4.2 VDC power to charge the spare battery.
• Compatible with the following battery:
• 7000 mAh PowerPrecision+ standard battery
Figure 19 4-Slot Spare Battery Charger
Spare Battery Charging LED
Power LED
19
MC93XX Quick Start Guide
16-Slot Spare Battery Charger
The 16-Slot Spare Battery Charger:
• Charges up to 16 spare batteries.
• Provides 4.2 VDC power to charge the spare battery.
• Compatible with the following battery:
• 7000 mAh PowerPrecision+ standard battery
Figure 20 16-Slot Spare Battery Charger
Power LED
Spare Battery Charging LED
20
MC93XX Quick Start Guide
USB Charge/Com Snap-on Cup
The USB Charge/Com Snap-on Cup:
• Provides 5 VDC power to operate the device and to charge the battery.
• Provides power and/or communication with the host computer over USB to the device.
• Compatible with devices using the following battery:
• 7000 mAh PowerPrecision+ standard battery
Figure 21 USB Charge/Com Snap-on Cup
USB Charge/Com Snap-on Cup
Pigtail with USB Socket
21
MC93XX Quick Start Guide
MC93XX Charge Only Adapter
Use the Charge Only Adapter for backwards compatibility with the MC9XXX cradles and the MC93XX mobile computer.
• Charge Only Adapter supports terminal charging only for the MC9XXX 1-Slot Cradle and 4-Slot Cradle.
• Charge Only Adapter provides charge only and no communication when used with the MC9XXX cradles.
22
MC93XX Quick Start Guide
Figure 22 MC9X 1-Slot Cradle Charge Only Adapter
Charge Only Adapter
Figure 23 MC9X 4-Slot Cradle Charge Only Adapter
MC92 1-Slot Cradle
Charge Only Adapter
MC92 4-Slot Cradle
Charge Only Adapter Installation
To install the Charge Only Adapter:
1. Clean the MC9XXX cradle and contacts surface as specified with an alcohol wipe, using a back and forth motion with your finger.
For more information about cleaning, refer to the MC93XX Mobile Computer User Guide.
23
MC93XX Quick Start Guide
Figure 24 Clean MC9XXX Cradle Contacts and Surfaces
Clean Cradle Contacts and Surface
2. Peel and remove the adhesive from the back of the adapter.
Figure 25 Peel and Remove Adhesive
Peel and Remove Adhesive
3. Insert the adapter into the MC9XXX cradle and adhere to the bottom of the cradle.
24
MC93XX Quick Start Guide
Figure 26 Insert Adapter into Cradle
4. Insert the device into the cradle.
Figure 27 Insert Device into Cradle
25
MC93XX Quick Start Guide
Scanning
The MC93XX offers the following data capture options:
• SE4750-SR 1D/22D imager
• SE4850-ER 1D/2D imager
• SE965 1D laser scanner
Refer to the MC93XX Mobile Computer User Guide for additional scanning options.
Barcode Capture with Imager
To capture barcode data:
1. Ensure that an application is open on the device and a text field is in focus (text cursor in text field).
2. Point the top of the device at a barcode.
3. Press and hold the Scan button or trigger.
The red laser aiming pattern turns on to assist in aiming.
4. Ensure the barcode is within the area formed by the cross-hairs in the aiming pattern. The aiming dot is used for increased visibility in bright lighting conditions.
The Scan LEDs light green and a beep sounds, by default, to indicate the barcode was decoded successfully.
Note that when the device is in Pick List Mode, the device does not decode the barcode until the center of the crosshair touches the barcode.
Figure 28 Aiming Pattern: Standard and Extended Range
Figure 29 Pick List Mode with Multiple Barcodes in Aiming Pattern: Standard and Extended Range
5. Release the Scan button or trigger.
6. The barcode content data appears in the text field.
Barcode Capture with Laser Scanner
To capture barcode data:
1. Ensure that an application is open on the device and a text field is in focus (text cursor in text field).
2. Point the top of the device at a barcode.
26
MC93XX Quick Start Guide
3. Point the scan exit window at a bar code.
4. Press and hold the Scan button or trigger.
The red scan line turns on to assist in aiming. Ensure that the scan line crosses every bar and space of the barcode.
The Scan LEDs light green and a beep sounds, by default, to indicate the barcode was decoded successfully.
Figure 30 Laser Scanner Aiming Pattern
5. Release the Scan button or trigger.
The captured data appears in the text field.
27
MC93XX Quick Start Guide
Ergonomic Considerations
Taking breaks and task rotation are recommended.
Optimum Body Posture
Figure 31 Optimum Upright Body Posture
Alternate left and right hand.
28
MC93XX Quick Start Guide
Optimize Body Posture for Scanning
Figure 32 Low and High Scanning
Alternate left and right knees
Avoid Reaching and Bending
Figure 33 Avoid Reaching and Bending
Use a ladder.
29
MC93XX Quick Start Guide
Avoid Extreme Wrist Angles
Figure 34 Avoid Extreme Wrist Angles
30
www.zebra.com
