Asus M2V-MX SE Motherboard User Manual

M2V-MX SE

E3023

First Edition

July 2007 ii

Copyright © 2007 ASUSTeK COMPUTER INC. All Rights Reserved.

No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).

Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing.

ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS

OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS

DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,

LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),

EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY

DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR

INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,

AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO

RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS

MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.

Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.

Contents

Notices.......................................................................................................... vi

Safety.information...................................................................................... vii

M2V-MX.SE

specifications summary ....................................................... viii

Chapter.1:.

Product introduction .

1.1.

Welcome!....................................................................................... 1-2

1.2.

Package.contents.......................................................................... 1-2

1.3 Special features ............................................................................. 1-2

1.3.1 Product highlights ........................................................... 1-2

1.3.2 Innovative ASUS features .............................................. 1-4

1.4 Before you proceed ...................................................................... 1-5

1.5.

Motherboard.overview.................................................................. 1-6

1.5.1 Motherboard layout ......................................................... 1-6

1.5.2 Placement direction ........................................................ 1-7

1.5.3 Screw holes .................................................................... 1-7

1.6.

Central.Processing.Unit.(CPU).................................................... 1-8

1.6.1 Installing the CPU ........................................................... 1-8

1.6.2 Installing the heatsink and fan ...................................... 1-10

1.7.

System.memory.......................................................................... 1-12

1.7.1 Overview ....................................................................... 1-12

1.7.2 Memory configurations .................................................. 1-12

1.7.3 DDR2 Qualified Vendoros List ...................................... 1-13

1.7.4 Installing a DIMM .......................................................... 1-17

1.7.5 Removing a DIMM ........................................................ 1-17

1.8.

Expansion.slots........................................................................... 1-18

1.8.1 Installing an expansion card ......................................... 1-18

1.8.2 Configuring an expansion card ..................................... 1-18

1.8.3 PCI slots ........................................................................ 1-20

1.8.4 PCI Express x1 slot ....................................................... 1-20

1.8.5 PCI Express x16 slot ..................................................... 1-20

1.9 Jumpers ....................................................................................... 1-21

1.10. Connectors.................................................................................. 1-23

1.10.1 Rear panel connectors .................................................. 1-23

1.10.2 Internal connectors ....................................................... 1-24 iii

iv

Contents

Chapter.2:.

BIOS setu p

2.1 Managing and updating your BIOS ............................................. 2-2

2.1.1 Creating a bootable floppy disk ....................................... 2-2

2.1.2 ASUS EZ Flash utility ...................................................... 2-3

2.1.3 AFUDOS utility ................................................................ 2-4

2.1.4 ASUS CrashFree BIOS 2 utility ...................................... 2-6

2.1.5 ASUS Update utility ........................................................ 2-8

2.2 BIOS setup program ................................................................... 2-11

2.2.1 BIOS menu screen ........................................................ 2-12

2.2.2 Menu bar ....................................................................... 2-12

2.2.3 Navigation keys ............................................................. 2-12

2.2.4 Menu items ................................................................... 2-13

2.2.5 Sub-menu items ............................................................ 2-13

2.2.6 Configuration fields ....................................................... 2-13

2.2.7 Pop-up window ............................................................. 2-13

2.2.8 Scroll bar ....................................................................... 2-13

2.2.9 General help ................................................................. 2-13

2.3 Main menu ................................................................................... 2-14

2.3.1 System Time ................................................................. 2-14

2.3.2 System Date ................................................................. 2-14

2.3.3 Legacy Diskette A ........................................................ 2-14

2.3.4 Primary and Secondary IDE Master/Slave .................. 2-15

2.3.5 SATA1 and SATA2 ........................................................ 2-17

2.3.6 IDE Configuration .......................................................... 2-18

2.3.7 System Information ....................................................... 2-19

2.4 Advanced menu .......................................................................... 2-20

2.4.1 USB Configuration ........................................................ 2-20

2.4.2 CPU Configuration ........................................................ 2-22

2.4.3 Chipset .......................................................................... 2-23

2.4.4 Onboard Devices Configuration .................................... 2-28

2.4.5 PCI PnP ........................................................................ 2-29

2.5 Power menu ................................................................................. 2-30

2.5.1 Suspend Mode .............................................................. 2-30

2.5.2 ACPI Version Support ................................................... 2-30

2.5.3 ACPI APIC Support ....................................................... 2-30

Contents

2.5.4 APM Configuration ........................................................ 2-31

2.5.5 Hardware Monitor ......................................................... 2-33

2.6 Boot menu ................................................................................... 2-34

2.6.1 Boot Device Priority ...................................................... 2-34

2.6.2 Boot Settings Configuration .......................................... 2-35

2.6.3 Security ......................................................................... 2-36

2.7.

Exit menu ..................................................................................... 2-39

Chapter.3:.

Software support .

3.1.

Installing.an.operating.system.................................................... 3-2

3.2 Support CD information ............................................................... 3-2

3.2.1 Running the support CD ................................................. 3-2

3.2.2 Drivers menu ................................................................... 3-3

3.2.3 Utilities menu .................................................................. 3-4

3.2.4 Make Disk menu ............................................................. 3-6

3.2.5 Manual menu .................................................................. 3-7

3.2.5 ASUS Contact information .............................................. 3-8 v

vi

Notices

Federal Communications Commission Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference, and

• This device must accept any interference received including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Canadian Department of Communications Statement

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the

Canadian Department of Communications.

This class B digital apparatus complies with Canadian

ICES-003.

Safety information

Electrical.safety

• To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system.

• When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.

• Before connecting or removing signal cables from the motherboard, ensure that all power cables are unplugged.

• Seek professional assistance before using an adapter or extension cord.

These devices could interrupt the grounding circuit.

• Make sure that your power supply is set to the correct voltage in your area. If you are not sure about the voltage of the electrical outlet you are using, contact your local power company.

• If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.

Operation.safety

• Before installing the motherboard and adding devices on it, carefully read all the manuals that came with the package.

• Before using the product, make sure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your dealer immediately.

• To avoid short circuits, keep paper clips, screws, and staples away from connectors, slots, sockets and circuitry.

• Avoid dust, humidity, and temperature extremes. Do not place the product in any area where it may become wet.

• Place the product on a stable surface.

• If you encounter technical problems with the product, contact a qualified service technician or your retailer.

The symbol of the crossed out wheeled bin indicates that the product (electrical and electronic equipment) should not be placed in municipal waste. Check local regulations for disposal of electronic products.

vii

viii

M2V-MX SE specifications summary

CPU

Chipset

System Bus

Memory

Expansion slots

Graphics

Storage

Audio

LAN

USB 2.0

Special features

Backpanel I/O ports

Support AMD socket AM2 for AMD Athlon™ 64 FX/

Athlon™ 64 X2/Athlon™ 64/AMD Sempron™/

AMD Opetron™ processor

AMD64 architecture enables simultaneous 32-bit and

64-bit computing

Supports AMD Cool ‘n’ Quiet™ Technology

VIA ® K8M890

VIA ® VT8237S

2000 MT/s

2 x 240-pin DIMM sockets support up to 2 GB of ECC/

non-ECC unbufferred DDR2 800/667/533 MHz DIMMs

1 x PCI Express™ x16 slot

1 x PCI Express™ x1 slot

2 x PCI slots

Integrated in the Gfx in North Bridge

Supports a maximum of 256MB shared memory

VIA ® VT8237S supports:

- 2 x Ultra DMA 133/100/66/33

- 2 x Serial ATA 3.0 Gb/s hard disk drives supporting

RAID 0, RAID 1, and JBOD configurations

Realtek ® ALC662-GR Azalia 6-channel audio CODEC

Supports Multi-Streaming Technology

S/PDIF out support

Phy 10/100 LAN

Supports up to 8 USB 2.0 ports

ASUS EZ Flash

ASUS CrashFree BIOS 2

ASUS MyLogo™

ASUS C.P.R. (CPU Parameter Recall)

ASUS Q-Fan technology

ASUS Fanless thermal solution

1 x Parallel port

1 x PS/2 keyboard port

1 x PS/2 mouse port

1 x 6-channel Audio I/O port

1 x RJ45 port

1 x VGA port

4 x USB ports

1 x Serial port

(continued on the next page)

M2V-MX SE specifications summary

Internal I/O connectors

BIOS features

Manageability

Support CD contents

Form factor

2 x USB connector supports additional 4 USB ports

24-pin ATX power connector

4-pin ATX 12V power connector

1 x S/PDIF out connector

1 x CD audio-in connector

1 x CPU/ 1 x Chassis fan connectors

1 x Front Panel High Definition audio connector

1 x 10-1 pin system panel connector

1 x 4-pin speaker connector

4 Mb Flash ROM, AMI BIOS, PnP, DMI2.0, WfM2.0, SM

BIOS 2.4, ACPI 3.0

WfM 2.0, DMI 2.0, WOL/WOR by PME, PXE, WOR by Ring,

Drivers

Anti-virus software

ASUS LiveUpdate

ASUS InstALL

ASUS PC ProbeII uATX form factor: 9.6 in x 7.6 in

*Specifications are subject to change without notice. ix

x

This chapter describes the motherboard features and the new technologies it supports.

1

introduction

1-2

1.1 Welcome!

Thank you for buying an ASUS ® M2V-MX SE motherboard!

The motherboard delivers a host of new features and latest technologies, making it another standout in the long line of ASUS quality motherboards!

Before you start installing the motherboard, and hardware devices on it, check the items in your package with the list below.

1.2 Package contents

Check your motherboard package for the following items.

Motherboard ASUS M2V-MX SE motherboard

Cables

Accessories

Application CD

Documentation

1 x Serial ATA signal cables

1 x Serial ATA power cable

1 x Ultra DMA 133/100/66 cable

1 x Floppy disk drive cable

I/O shield

ASUS motherboard support CD

User guide

If any of the above items is damaged or missing, contact your retailer.

1.3 Special features

1.3.1 Product highlights

Latest.processor.technology..

.

.

The motherboard supports AMD socket AM2 single-core Athlon 64/ Sempron and dual-core Athlon 64FX/ Athlon 64 X2 processors with 2MB/1MB/512KB L2 cache, which is based on 64-bit architecture. It features 2000/1600 MT/s HyperTransport

Bus, dual-channel ECC/non-ECC unbuffered DDR2 800 memory support and AMD

Cool ‘n’ Quiet Technology. See page 1-8 for details.

Chapter 1: Product introduction

AMD Cool ‘n’ Quiet Technology ..

The motherboard supports the AMD Cool ‘n’ Quiet Technology, which monitors system operation and automatically adjusts CPU voltage and frequency for a cool and quiet operating environment.

DDR2 800MHz memory support .....

DDR2 is the next generation memory technology to replace the current DDR. With the highest speed up to 800MHz, DDR2 memory provides great performance for

3D graphics and other memory demanding applications.

PCI.Express™.interface..

The motherboard fully supports PCI Express, the latest I/O interconnect technology that speeds up the PCI bus. PCI Express features point-to-point serial interconnections between devices and allows higher clockspeeds by carrying data in packets. This high speed interface is software compatible with existing PCI specifications. See page 1-20 for details.

USB.2.0.technology.

.

The motherboard implements the Universal Serial Bus (USB) 2.0 specification, dramatically increasing the connection speed from the 12 Mbps bandwidth on USB

1.1 to a fast 480 Mbps on USB 2.0. USB 2.0 is backward compatible with USB 1.1.

See pages 1-24 and 1-28 for details.

10/100.Mbps.LAN

Easy connectivity to your network or broadband connection with the onboard LAN port, lets you take gaming online without buying expensive additional LAN cards.

See page 1-23 for details.

ASUS M2V-MX SE 1-3

1-4

1.3.2 Innovative ASUS features

ASUS.EZ.Flash..

.

With the ASUS EZ Flash, you can easily update the system BIOS even before loading the operating system. No need to use a DOS-based utility or boot from a floppy disk. See page 2-3 for details.

CrashFree.BIOS.2.

.

This feature allows you to restore the original BIOS data from the support CD in case when the BIOS codes and data are corrupted. This protection eliminates the need to buy a replacement ROM chip. See page 2-6 for details.

ASUS Q-Fan technology .

The ASUS Q-Fan technology smartly adjusts the CPU speed according to the system loading to ensure quiet, cool, and efficient operation. See page 2-33 for details.

ASUS.MyLogo™.

This new feature present in the motherboard allows you to personalize and add styles to your system with customizable boot logos. See page 2-35 for details.

C.P.R. (CPU Parameter Recall)

The C.P.R. feature of the motherboard BIOS allows automatic re-setting to the

BIOS default settings in case the system hangs due to overclocking. When the system hangs due to overclocking, C.P.R. eliminates the need to open the system chassis and clear the RTC data. Simply shut down and reboot the system, and the

BIOS automatically restores the CPU default setting for each parameter.

Due to chipset behavior, AC power off is required prior using C.P.R. function.

Fanless Design

The ASUS fanless design allows multi-directional heat flow from major thermal sources in the motherboard to lower overall system temperature, resulting in quieter operation and longer system life. ASUS has devoted special efforts to address the thermal issues across the motherboard, and most notably in the following areas:

CPU, power, VGA, Northbridge and Southbridge.


1.4 Before you proceed

Take note of the following precautions before you install motherboard components or change any motherboard settings.

• Unplug the power cord from the wall socket before touching any component.

• Use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity

• Hold components by the edges to avoid touching the ICs on them.

• Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that came with the component.

• Before you install or remove any component, ensure that the ATX power supply is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, and/or components.

Onboard LED

The motherboard comes with a standby power LED that lights up to indicate that the system is ON, in sleep mode, or in soft-off mode. This is a reminder that you should shut down the system and unplug the power cable before removing or plugging in any motherboard component. The illustration below shows the location of the onboard LED.

M2V-MX.SE

M2V -MX SE Onboard LED

ON

Power

SB_PWR

OFF

Off

ASUS M2V-MX SE 1-5

1-6

1.5 Motherboard overview

1.5.1 Motherboard layout

19.3cm (7.6in)

PS/2KBMS

B: Keyboard ATX12V

USB34

LAN1_USB12

CPU_FAN

W83124RG-A2

AUDIO

PCIEX1_1

Attansic

F2

VIA K8M890

M2V-MX.SE

PCIEX16

Super I/O

PCI1

ALC662

SPDIF_OUT

AAFP

USB56

PCI2

FLOPPY

USBPW5-8

SB_PWR

Lithium Cell

CMOS Power

4Mb

BIOS

VIA VT8237S

SATA2

SATA1

USB78 F_PANEL

SPEAKER


1.5.2.

Placement.direction

When installing the motherboard, make sure that you place it into the chassis in the correct orientation. The edge with external ports goes to the rear part of the chassis as indicated in the image below.

1.5.3.

Screw.holes

Place six (6) screws into the holes indicated by circles to secure the motherboard to the chassis.

Do not overtighten the screws! Doing so can damage the motherboard.

Place.this.side.towards.

the.rear.of.the.chassis

M2V-MX.SE

ASUS M2V-MX SE 1-7

1.6 Central Processing Unit (CPU)

The motherboard comes with a 940-pin AM2 socket designed for the AMD

Opetron TM /AMD processor.

Athlon™ 64 FX/Athlon™ 64 X2/AMD Athlon™ 64/AMD Sempron™

Make sure you use a CPU is designed for the AM2 socket. The CPU fits in only one correct orientation. DO NOT force the CPU into the socket to prevent bending the connectors on the socket and damaging the CPU!

1.6.1. Installing.the.CPU

To install a CPU.

1. Locate the CPU socket on the motherboard.

M2V-MX.SE

M2V-MX.SE.CPU.Socket.AM2

2. Unlock the socket by pressing the lever sideways, then lift it up to a

90°-100° angle.

Socket.lever

1-8

Make sure that the socket lever is lifted up to 90°-100° angle, otherwise the

CPU does not fit in completely.


3. Position the CPU above the socket such that the CPU corner with the gold triangle matches the socket corner with a small triangle.

4. Carefully insert the CPU into the socket until it fits in place.

Small.triangle

Gold.triangle

The CPU fits only in one correct orientation. DO NOT force the CPU into the socket to prevent bending the pins and damaging the CPU!

5. When the CPU is in place, push down the socket lever to secure the

CPU. The lever clicks on the side tab to indicate that it is locked.

6. Install a CPU heatsink and fan following the instructions that came with the heatsink package.

7. Connect the CPU fan cable to the CPU_FAN connector on the motherboard.

CPU_FAN

CPU FAN PWM

CPU FAN PWR

M2V-MX.SE

M2V-MX.SE.CPU.Fan.Connector

Do not forget to connect the CPU fan connector! Hardware monitoring errors can occur if you fail to plug this connector.

ASUS M2V-MX SE 1-9

1.6.2.

Installing.the.heatsink.and.fan

The AMD Opetron™/AMD Athlon™ 64 FX/ AMD Athlon™ 64 X2/AMD Athlon™

64/AMD Sempron™ processor require a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance.

Make sure that you use only qualified heatsink and fan assembly.

Follow these steps to install the CPU heatsink and fan.

1. Place the heatsink on top of the installed CPU, making sure that the heatsink fits properly on the retention module base.

• The retention module base is already installed on the motherboard upon purchase.

• You do not have to remove the retention module base when installing the CPU or installing other motherboard components.

• If you purchased a separate CPU heatsink and fan assembly, make sure that a Thermal Interface Material is properly applied to the CPU heatsink or CPU before you install the heatsink and fan assembly.

1-10

CPU.Fan

CPU Heatsink

Retention Module Base

Retention bracket Retention bracket lock

Your boxed CPU heatsink and fan assembly should come with installation instructions for the CPU, heatsink, and the retention mechanism. If the instructions in this section do not match the CPU documentation, follow the latter.


2. Attach one end of the retention bracket to the retention module base.

3. Align the other end of the retention bracket (near the retention bracket lock) to the retention module base. A clicking sound denotes that the retention bracket is in place.

Make sure that the fan and heatsink assembly perfectly fits the retention mechanism module base; otherwise, you cannot snap the retention bracket in place.

4. Push down the retention bracket lock on the retention mechanism to secure the heatsink and fan to the module base.

ASUS M2V-MX SE 1-11

1.7 System memory

1.7.1.

Overview

The motherboard comes with two Double Data Rate 2 (DDR2) Dual Inline Memory

Modules (DIMM) sockets.

A DDR2 module has the same physical dimensions as a DDR DIMM but has a

240-pin footprint compared to the 184-pin DDR DIMM. DDR2 DIMMs are notched differently to prevent installation on a DDR DIMM socket.

The figure illustrates the location of the DDR2 DIMM sockets:

1-12

M2V-MX.SE

M2V -MX SE 240-pin DDR2 DIMM Sockets

1.7.2 Memory configurations

You may install 256 MB, 512 MB, 1 GB, and 2 GB ECC/non-ECC unbuffered

DDR2 DIMMs into the DIMM sockets.

• Due to chipset resource allocation, the system may detect less than

4 GB system memory when you installed two 2 GB DDR2 memory modules.

• For optimum compatibility, we recommend that you obtain memory modules from the same vendor. Visit the ASUS website

(www.asus.com) for the latest Qualified Vendors List.


1.7.3 DDR2 Qualified Vendors List

The following table lists the memory modules that have been tested and qualified for use with this motherboard. Visit the ASUS website (www.asus.com) for the latest DDR2 DIMM modules for this motherboard.

DDR2 533 Qualified Vendors List

Size Vendor Model Side(s)

256MB AENEON AET560UD00-370A98Z SS



512MB AENEON AET660UD00-370A98X SS

512MB AENEON AET660UD00-370A88S DS

512MB AENEON AET660UD00-370B97X SS

1G AENEON AET760UD00-370A98Z DS

1G

1G

2G

AENEON AET760UD00-370A98S DS

AENEON AET760UD00-370B97X DS

AENEON AET860UD00-370A08X DS

512MB Corsair

512MB Elpida

256MB HY

VS512MB533D2 DS

EBE51UD8ABFA-5C-E SS

HYMP532U64CP6-C4 AB SS

1G HY HYMP512U64CP8-C4 AB DS

256MB Kingmax KLBB68F-36EP4 SS

512MB Kingmax KLBC28F-A8KB4

512MB Kingmax KLBC28F-A8EB4

SS

SS

256MB Kingston KVR533D2N4/256


SS

SS

512MB Kingston KVR533D2N4/512 DS


1G Kingston KVR533D2N4/1G

SS

DS

512MB Micron MT 16HTF6464AG-53EB2 DS

512MB Micron

1G Micron

512MB PQI

MT 16HTF6464AG-53EB2 DS

MT 16HTF12864AY-53EA1 DS

MEAB-323LA SS

1G PQI MEAB-423LA DS

256MB Qimonda HYS64T32000HU-3.7-A SS

512MB Qimonda HYS64T64000GU-3.7-A SS



512MB REMAXEL RML1040EG38D6F-533 SS

256MB Samsung M378T3253FG0-CD5 SS

512MB Samsung M378T6553BG0-CD5 SS

512MB Transcend 512MB DDR2 533 ECC SS

512MB VERITECH GTP512HLTM46DG

1G VERITECH GTP01GHLTM56DG

SS

DS

Component

AET94F370AWVV34635G0520

AET93F370A G 0513

AET93F370A 3VV36328G 0522

AET93F370A 0518

AET82F370A 0550

AET93R370B 0640

AET93F370A 0551

AET92F370A 0606

AET93R370B 0640

AET03F370AFVV26176G 0542

MIII0052532M8CEC

E5108AB-5C-E

HY5PS121621CFP-C4

HY5PS12821CFP-C4

E5116AB-5C-E

KKEA88B4IAK-37

E5108AE-5C-E

E5116AB-5C-E

E5116AF-5C-E

HY5PS56821F-C4

HYB18T512800AF3733336550

D6408TE7BL-37

D9BOM

Z9BQT

D9CRZ

D2-E04180W025

D2-E04230W107

HYB18T512160AF-3.7AFSS31270

HYB18T512800AC37SSS11511

HYB18T512800AF37SSS12079

HYB18T512800AF37FSS29334

E5108AG-5C-E

K4T56083QF-GCD5

K4T51083QB-GCD5

6ND22D9GCT(ECC)

VTD264M8PC6G01A164129621

VTD264M8PC6G01A164129621

•

•

•

•

•

•

•

•

•

•

•

•

•

•

• •

•

•

•

• •

• •

DIMM support

A B

• •

• •

• •

• •

• •

• •

• •

• •

• •

• •

•

•

•

•

•

•

•

ASUS M2V-MX SE 1-13

1-14


Size Vendor

512MB ADATA

Model Side(s)

M20EL5G3H3160B1C0Z SS

Component

E5108AE-6E-E

513MB ADATA

1G ADATA

M20AD5G3H3166I1C52 SS

M2OAD5G3I4176I1C52 DS

512MB AENEON AET660UD00-30DA98Z SS

512MB AENEON AET660UD00-30DB97X SS

AD29608A8A-3EG20648

AD29608A8A-3EG20645

AET93F30DA 0552

AET93R300B 0634

512MB AENEON AET660UD00-30DA98Z SS

1G AENEON AET760UD00-30DA98Z DS

1G AENEON AET760UD00-30DA98Z DS

1G AENEON AET760UD00-30DB97X DS

512MB Apacer 78.91092.420 SS

512MB Apacer AU512E667C5KBGC SS

AET93F300A 0606

AET93F30DA8EE47414G 0540

AET93F30DA 0604

AET93R300B 0639

E5108AE-6E-E

AM4B5708MIJS7E0627B

512MB Apacer

1G Apacer

1G Apacer

1G Apacer

512MB Century

512MB Century

1G Century

1G Century

512MB Corsair

512MB Corsair

1G Corsair

512MB GEIL

256MB HY

512MB HY

512MB HY

512MB HY

512MB HY

AU512E667C5KBGC SS

AU01GE667C5KBGC DS

78.01092.420 DS

AU01GE667C5KBGC DS

CENTURY 512MB

CENTURY 512MB

CENTURY 1G

CENTURY 1G

VS512MB667D2

CM2X512-5400C4

SS

SS

DS

DS

DS

SS

VS1GB667D2

GX21GB5300DC

DS

SS

HYMP532U64CP6-Y5 AB SS

HYMP564U64AP8-Y4 AA SS

HYMP564U64AP8-Y5 AA SS

HYMP564U72AP8-Y4 SS

HYMP564U72AP8-Y5 SS

AM4B5708GQJS7E06332F

AM4B5708GQJS7E0636B

E5108AE-6E-E

AM4B5708MIJS7E0627B

NT5TU64M8AE-3C

HY5PS12821AFP-Y5

HY5PS12821AFP-Y5

NT5TU64M8AE-3C

MIII0052532M8CEC

Heat-Sink Package

MID095D62864M8CEC

Heat-Sink Package

HY5PS121621CFP-Y5

HY5PS12821AFP-Y4

HY5PS12821AFP-Y5

HY5PS12821AFP-Y4(ECC)


1G

1G

1G

HY

HY

HY

HYMP512U72AP8-Y5 DS

HYMP512U64AP8-Y5 AB DS

HYMP512U64CP8-Y5 AB DS

512MB KINGBOX 512MB 667MHz

1G KINGBOX DDRII 1G 667MHz

512MB Kingmax KLCC28F-A8EB5

SS

DS

SS

512MB Kingmax KLCC28F-A8KB5

1G Kingmax KLCD48F-A8KB5



SS

DS

SS

SS

512MB Kingston KVR667D2E5/512



512MB MDT

1G MDT

1G MDT

MDT 512MB

MDT 1024MB

MDT 1024MB

SS

DS

DS

SS

DS

DS


HY5PS12821AFP-Y5

HY5PS12521CFP-Y5

EPD264082200-4

EPD264082200-4

E5108AE-6E-E

KKEA88B4LAUG-29DX

KKEA88B4LAUG-29DX

E2508AB-6E-E

D6408TE8WL-27

E5108AE-6E-E(ECC)

D6408TE8WL-3

D6408TEBGGL3U

18D51280D-30648

18D51200D-30646

18D51280D-30646E

(continued on the next page)

•

•

•

•

• •

• •

• •

• •

•

•

•

• •

•

•

•

•

•

DIMM support

A B

•

•

•

• •

• •

• •

• •

• •

• •

•

•

•

•

•

• •

• •

•

•

•

•

•

•

•

•

• •

• •

• •



Size Vendor

256MB Nanya

256MB Nanya

512MB Nanya

512MB Nanya

1G PQI

512MB PSC

512MB PSC

DIMM support

Model Side(s) Component A B

NT256T64UH4A1FY-3C SS

NT256T64UH4A1FY-3C SS

NT512T64U88A1BY-3C SS

NT5TU32M16AG-3C

NT5TU32M16AG-3C

NT5TU64M8AE-3C

• •

•

• •

NT512T64U88A1BY-3C SS

DDR2-667U 1G DS

AL6E8E63B-6E1K

AL6E8E63B-6E1K

SS

SS

NT5TU64M8AE-3C

HY5PS12821BFP-E3 A

A3R12E3GEF637BLC5N

A3R12E3GEF637BLC5N

•

• •

• •

•

1G

1G

PSC

PSC

AL7E8E63B-6E1K

AL7E8E63B-6E1K

DS

DS

256MB Qimonda HYS64T32000HU-3S-A SS



1G Qimonda HYS64T128020HU-3S-A DS

512MB Samsung KR M378T6553CZ0-CE6 SS

512MB Samsung KR M378T6453FZ0-CE6 DS

512MB Samsung M378T6553CZ3-CE6 SS

1G

1G

Samsung M378T2953CZ3-CE6 DS

Samsung KR M378T2953CZ0-CE6 DS

512MB TEAM

1G TEAM

TVDD512M667C5

TVDD1.02M667C4

SS

DS

512MB VDATA

512MB VDATA

512MB VDATA

1G

1G

1G

VDATA

VDATA

VDATA

M2GVD5G3H31A4I1C52 SS

M2YVD5G3H31P4I1C52 SS

M2GVD5G3H166I1C52 SS

M2GVD5G3I41P6I1C52 DS

M2GVD5G3I41C4I1C52 DS

M2GVD5G3I4176I1C52 DS

512MB VERITECH GTP512HLTM45EG

1G VERITECH GTP01GHLTM55EG

SS

DS

A3R12E3GEF637BLC5N

A3R12E3GEF637BLC5N

HYB18T512160AF-3SSSS17310

HYB18T5128000AF-3SSSS27416

HYB18T512800AF3SFSS05346

HYB18T512800AF3SSSS28104

K4T51083QC

K4T56083QF-ZCE6

K4T51083QC-ZCE6

K4T51083QC-ZCE6

K4T51083QC-ZCE6

T2D648MT-6

T2D648PT-6

VD29608A8A-3EC20615

VD29608A8A-3EG20627

VD29608A8A-3EG20637

VD29608A8A-3EG20627

VD29608A8A-3EC20620

VD29608A8A-3EG20641

VTD264M8PC6G01A164129621

VTD264M8PC6G01A164129621

• •

•

•

•

•

•

•

•

•

•

•

• •

• •

•

•

•

•

•

•

• •

• •

ASUS M2V-MX SE 1-15

1-16


Size Vendor Model Side(s) Component

512MB AENEON AET660UD00-25DB98X SS

1G AENEON AET760UD00-25DB97X DS

AET93F25DB 0621

AET93R25DB 0640

512MB Corsair

1G Corsair

512MB HY

CM2X512A-6400

CM2X1024-6400

SS

DS

HYMP564U64AP8-S6 AA SS

Heat-Sink Package

Heat-Sink Package

HY5PS12821AFP-S6

512MB HY

512MB HY

1G

1G

HY

HY

HYMP564U64BP8-S5 AB SS

HYMP564U64CP8-S5 AB SS

HYMP512U64AP8-S6 AA DS

HYMP512U64BP8-S5 AB DS

1G HY HYMP512U64CP8-S5 AB DS

512MB Kingston KVR800D2N5/512 SS

512MB Kingston KVR800D2N5/512 SS

1G

1G

1G

Kingston

Kingston

Kingston

KVR800D2N5/1G

KHX6400D2LL/1G

KVR800D2N5/1G

DS

DS

DS

512MB Micron

512MB PSC

512MB PSC

MT9HTF6472AY-80ED4 SS

AL6E8E63B-8E1K SS

AL6E8E63B-8E1K SS

1G

1G

PSC

PSC

AL7E8E63B-8E1K

AL7E8E63B-8E1K

DS

DS


512MB Qimonda HYS64T64020HU-2.5-A DS

HY5PS12821BFP-S5

HY5PS12821CFP-S5

HY5PS12821AFP-S6

HY5PS12821BFP-S5

6ED22D9GKX(ECC)

A3R12E3HEF641B9A05

A3R12E3HEF641B9A05

A3R12E3HEF641B9A05

A3R12E3HEF641B9A05

HYB18T256800AF25 SSS49313

HYB18T256800AF25 SSS25063

DIMM support

A B

• •

• •

•

•

•

•

•

•

•

HY5PS12821CFPS5

K4T51083QC-ZCE7

•

•

V59C1512804QBF25S0054707PEBPA •

K4T51083QC-ZCE7

Heat-Sink Package

NT5TU64M8BE-25C62321800CP

•

•

•

•

• •

•

• •

•

•

•



1G Samsung KR M378T2953CZ3-CE7 DS

1G

1G

Samsung KR M391T2953CZ3-CE7 DS

UMAX

512MB VDATA

1GB,DDR2,PC6400 DS

M2GVD6G3H3160I1E53 SS

1G VDATA M2GVD6G3I4170I1E53 DS

512MB VERITECH GTU512HLTXX4EG SS

1G VERITECH GTU01GHLTXX4EG DS

K4T51083QC-ZCE7

K4T51083QC-ZCE7(ECC)

K4T51083QC-ZCE7

K4T51083QC-ZCE7(ECC)

U2S12D30TP-8E

VD29608A8A-25EG30648

VD29608A8A-25EG30647

VTD264M8PC4G03A169045648

VTD264M8PC4G03A169045648

•

•

•

•

• •

•

•

• •

• •

Side(s): SS - Single Sided DS - Double Sided

DIMM Support:

A - supports one module inserted in any slot as Single-channel memory configuration

B - supports one pair of modules inserted into either slots as one pair of Dual-channel memory configuration

Visit the ASUS website (www.asus.com) for the latest memory Qualified Vendor

List (QVL).


1.7.3 Installing a DIMM

Unplug the power supply before adding or removing DIMMs or other system components. Failure to do so can cause severe damage to both the motherboard and the components.

To install a DIMM:

1. Unlock a DIMM socket by pressing the retaining clips outward.

2. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket.

3. Firmly insert the DIMM into the socket until the retaining clips snap back in place and the

DIMM is properly seated.

1

3

2

DDR2 DIMM notch

Unlocked.retaining.clip

• A DDR2 DIMM is keyed with a notch so that it fits in only one direction. Do not force a DIMM into a socket to avoid damaging the DIMM.

• The DDR2 DIMM sockets do not support DDR DIMMs. DO not install DDR

DIMMs to the DDR2 DIMM sockets.

1.7.4 Removing a DIMM

To remove a DIMM:

1. Simultaneously press the retaining clips outward to unlock the DIMM.

Support the DIMM lightly with your fingers when pressing the retaining clips. The DIMM might get damaged when it flips out with extra force.

1

2. Remove the DIMM from the socket.

2

DDR2 DIMM notch

1

ASUS M2V-MX SE 1-17

1-18

1.8 Expansion slots

In the future, you may need to install expansion cards. The following sub-sections describe the slots and the expansion cards that they support.

Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components.

1.8.1.

Installing.an.expansion.card

To install an expansion card:

1. Before installing the expansion card, read the documentation that came with it and make the necessary hardware settings for the card.

2. Remove the system unit cover (if your motherboard is already installed in a chassis).

3. Remove the bracket opposite the slot that you intend to use. Keep the screw for later use.

4. Align the card connector with the slot and press firmly until the card is completely seated on the slot.

5. Secure the card to the chassis with the screw you removed earlier.

6. Replace the system cover.

1.8.2 Configuring an

expansion.card

After installing the expansion card, configure it by adjusting the software settings.

1. Turn on the system and change the necessary BIOS settings, if any. See

Chapter 2 for information on BIOS setup.

2. Assign an IRQ to the card. Refer to the tables on the next page.

3. Install the software drivers for the expansion card.


Standard.

interrupt assignments

IRQ

10

11

12

13

14

15

7

8

5

6

9

2

3

0

1

4

Priority

7

8

5

6

9

10

13

14

15

3

4

1

2

–

11

12

Standard Function

System Timer

Keyboard Controller

Re-direct to IRQ#9

IRQ holder for PCI steering*

Communications Port (COM1)*


Floppy Disk Controller

Printer Port (LPT1)*

System CMOS/Real Time Clock




PS/2 Compatible Mouse Port*

Numeric Data Processor

Primary IDE Channel

Secondary IDE Channel

* These IRQs are usually available for ISA or PCI devices.

IRQ assignments for this motherboard

PCI slot 1

PCI slot 2

A B used —

— used

C

—

—

D

—

—

When using PCI cards on shared slots, ensure that the drivers support “Share

IRQ” or that the cards do not need IRQ assignments; otherwise, conflicts will arise between the two PCI groups, making the system unstable and the card inoperable.

ASUS M2V-MX SE 1-19

1-20

1.8.3.

PCI.slots

The PCI slots support cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications. The figure shows a LAN card installed on a PCI slot.

1.8.4.

PCI.Express.x1.slot

This motherboard supports PCI Express x1 network cards, SCSI cards and other cards that comply with the PCI Express specifications. The following figure shows a network card installed on the PCI

Express x1 slot.

1.8.5.

PCI.Express.x16.slot

This motherboard has supports PCI

Express x16 graphic cards that comply with PCI Express specifications. The figure shows a graphics card installed on the PCI Express x16 slot.


1.9 Jumpers

1. Clear RTC RAM (CLRTC)

This jumper allows you to clear the Real Time Clock (RTC) RAM in

CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords.

To erase the RTC RAM:

1. Turn OFF the computer and unplug the power cord.

2. Remove the onboard battery.

3. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on pins

2-3 for about 5~10 seconds, then move the cap back to pins 1-2.

4. Reinstall the battery.

5. Plug the power cord and turn ON the computer.

6. Hold down the <Del> key during the boot process and enter BIOS setup to re-enter data.

Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default position. Removing the cap will cause system boot failure!

CLRTC

M2V-MX.SE

M2V -MX SE Clear RTC RAM

Normal

(Default)

Clear RTC

ASUS M2V-MX SE 1-21

2..

USB device wake-up (3-pin PS2_USBPW1-4, USBPW5-8)

Set these jumpers to +5V to wake up the computer from S1 sleep mode

(CPU stopped, DRAM refreshed, system running in low power mode) using the connected USB devices. Set to +5VSB to wake up from S3 and S4 sleep modes (no power to CPU, DRAM in slow refresh, power supply in reduced power mode). Set PS2_USBPW1-4 jumper to +5VSB to wake up by PS2 mouse or keyboard.

The PS2_USBPW1-4 jumper is for the rear USB ports (PS_USB port 1-4).

The USBPW5-8 jumper is for the internal USB connectors (USB port 5-8) that you can connect to additional USB ports.

PS2_USBPW1-4

M2V-MX.SE

+5V

(Default)

1

+5VSB

USBPW5-8

3 3 5

+5VSB

M2V-MX.SE.

USB Device Wake Up

• The USB device wake-up feature requires a power supply that can provide 500 mA on the +5VSB lead for each USB port; otherwise, the system would not power up.

• The total current consumed must NOT exceed the power supply capability

(+5VSB) whether under normal condition or in sleep mode.

1-22 Chapter 1: Product introduction

1.10 Connectors

1.10.1 Rear panel connectors

1 2 3

11 10 9 8 7

1. PS/2 mouse port (green). This port is for a PS/2 mouse.

2. Parallel port. This 25-pin port connects a printer, scanner, or other devices.

3. LAN (RJ-45) port. This port allows 10/100 Mbps connection to a Local Area

Network (LAN) through a network hub.

4

5

6

LAN port LED indications

100Mbps LED 10Mbps LED Description

100Mbps.

LED

10Mbps.

LED

OFF

Yellow

OFF

Green

OFF

OFF

10Mbps connection

100Mbps connection

No link

LAN.port

4. Line In port (light blue) .

This port connects a tape, CD, DVD player, or other audio sources.

5. Line Out port (lime). This port connects a headphone or a speaker. In 4channel, or 6-channel, configuration, the function of this port becomes Front

Speaker Out.

6. Microphone port (pink). This port connects a microphone.

Refer to the audio configuration table below for the function of the audio ports in

2, 4, or 6-channel configuration.

Audio 2, 4, or 6-channel configuration

Port Headset

2-channel

Light Blue

Green

Pink

Line In

Line Out

Mic In

4-channel

Surround (Rear)

6-channel

Front Speaker Out Front Speaker Out

Mic In

Surround (Rear)

Bass/Center

ASUS M2V-MX SE 1-23

1-24

7. USB 2.0 ports 1 and 2. These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0 devices.

8. USB 2.0 ports 3 and 4. These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0 devices.

9. Video Graphics Adapter (VGA) port. This 15-pin port is for a VGA monitor or other VGA-compatible devices.

10. COM port. This 15-pin port is for a VGA monitor or other VGA-compatible devices.

11. PS/2 keyboard port (purple). This port is for a PS/2 keyboard.

1.10.2. Internal.connectors

1.. Floppy.disk.drive.connector.(34-1.pin.FLOPPY)

This connector is for the provided floppy disk drive (FDD) signal cable. Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive.

Pin 5 on the connector is removed to prevent incorrect cable connection when using an FDD cable with a covered Pin 5.

FLOPPY

M2V-MX.SE

NOTE: Orient the gray markings on the floppy ribbon cable to PIN 1.

M2V -MX SE Floppy Disk Drive Connector


2. IDE connectors (40-1 pin PRI_IDE, SEC_IDE)

The onboard IDE connectors are for Ultra DMA 133/100/66 signal cable(s).

There are three connectors on each Ultra DMA 133/100/66 signal cable: blue, black, and gray. Connect the blue connector to the motherboard’s IDE connector, then select one of the following modes to configure your device(s).

Single device

Two devices

Drive jumper setting

Mode of device(s)

Cable-Select or Master -

Cable-Select Master

Slave

Master

Slave

Master

Slave

Cable connector

Blue

Blue

Black

Blue or black

• Pin 20 on the IDE connector is removed to match the covered hole on the

Ultra DMA cable connector. This prevents incorrect insertion when you connect the IDE cable.

• Use the 80-conductor IDE cable for Ultra DMA 133/100/66 IDE devices.

If any device jumper is set as “Cable-Select,” make sure all other device jumpers have the same setting.

M2V-MX.SE

M2V-MX.SE.

IDE Connector s

NOTE: Orient the gray markings ribbon cable to PIN 1.

ASUS M2V-MX SE 1-25

3. Serial ATA connectors (7-pin SATA1[red], SATA2 [red])

These connectors are for the Serial ATA signal cables for Serial ATA hard disk and optical disk drives that allows 150 MB/s and 300MB/S data transfer rates, faster than the standard parallel ATA with 133 MB/s (Ultra DMA133).

If you install Serial ATA hard disk drives, you can create a RAID 0,

RAID 1, and JBOD configuration through the onboard VIA ® VT8237S controller.

M2V-MX.SE

SATA2

SATA1

M2V-MX.SE.

SATA Connectors

For detailed instructions on how to configure RAID 0, 1, and JBOD, refer to the

RAID manual in the support CD.


4. CPU, and Chassis Fan connectors .

(4-pin CPU_FAN, CHA_FAN)

The fan connectors support cooling fans of 350mA~740mA (8.88W max.) or a total of 1A~2.22A (26.64W max.) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector.

Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. These are not jumpers! DO NOT place jumper caps on the fan connectors.

CPU_FAN

CPU FAN PWM

CPU FAN PWR

M2V-MX.SE

M2V-MX.SE.Fan.Connectors

CHA_FAN

Rotation

+12V

GND

5. Optical drive audio in connectors (4-pin CD)

These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, TV tuner, or MPEG card.

M2V-MX.SE

CD

(black)

Right Audio Channel

Ground

Ground

Left Audio Channel

M2V-MX.SE.Internal.

Audio Connector

ASUS M2V-MX SE 1-27

6. USB connectors (10-1 pin USB56, USB78)

These connectors are for USB 2.0 ports. Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.0 specification that supports up to 480 Mbps connection speed.

USB56

USB+5V USB_P6- USB_P6+ GND NC

1

USB78

USB+5V USB_P8- USB_P8+ GND NC

1

M2V-MX.SE

USB+5V USB_P5- USB_P5+ USB+5V USB_P7- USB_P7+

M2V-MX.SE.USB.2.0.Connectors

Never connect a 1394 cable to the USB connectors. Doing so will damage the motherboard!

The USB 2.0 module is purchased separately.

7. Front panel audio connector (10-1 pin AAFP)

This connector is for a chassis-mounted front panel audio I/O module that supports the AC`97 audio standard. Connect one end of the front panel audio

I/O module cable to this connector.

AAFP

M2V-MX.SE

1-28

M2V-MX.SE.

Front Panel Audio Connector

• We recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboard’s high-definition audio capability.

• By default, this connector is set to HD Audio . If you want to connect a

AC'97 front panel audio module to this connector, set the Front.Panel.

Support Type item in the BIOS setup to [AC97]. See SouthBridge VIA

VT8237S Configuration in .

section 2.4.3 Chipset.


8. ATX power connectors (24-pin EATXPWR, 4-pin EATX12V)

These connectors are for an ATX power supply. The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit.

• We recommend that you use an ATX 12 V Specification 2.0-compliant power supply unit (PSU) with a minimum of 300 W power rating. This PSU type has 24-pin and 4-pin power plugs.

• If you intend to use a PSU with 20-pin and 4-pin power plugs, make sure that the 20-pin power plug can provide at least 15 A on +12 V and that the PSU has a minimum power rating of 300 W. The system may become unstable or may not boot up if the power is inadequate.

• Do not forget to connect the 4-pin ATX +12 V power plug; otherwise, the system will not boot up.

• We recommend that you use a PSU with higher power output when configuring a system with more power-consuming devices. The system may become unstable or may not boot up if the power is inadequate.

• You must install a PSU with a higher power rating if you intend to install additional devices.

M2V-MX.SE

+12V DC

GND

EATX12V

+12V DC

GND

+3 Volts

+12 Volts

+12 Volts

+5V Standby

Power OK

Ground

+5 Volts

Ground

+5 Volts

Ground

+3 Volts

+3 Volts

M2V -MX SE uATX Power Connector

EATXPWR

Ground

+5 Volts

+5 Volts

NC

-5 Volts

Ground

Ground

Ground

PSON#

Ground

-12 Volts

+3 Volts

ASUS M2V-MX SE 1-29

1-30

9.. System.panel.connector.(10-1.pin.PANEL)

This connector supports several chassis-mounted functions.

PWR LED PWR BTN

PLED- PWR

F_PANEL

M2V-MX.SE

+HDLED RESET

M2V-MX.SE.

System.Panel.Connector.

IDELED+ IDELED-

• System power LED (2-pin PWRLED)

This 2-pin connector is for the system power LED. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode.

• Hard disk drive activity LED (2-pin HDLED)

This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity

LED cable to this connector. The IDE LED lights up or flashes when data is read from or written to the HDD.

• Power/Soft-off button (2-pin PWRBTN)

This connector is for the system power button. Pressing the power button turns the system ON or puts the system in SLEEP or SOFT-OFF mode depending on the BIOS settings. Pressing the power switch for more than four seconds while the system is ON turns the system OFF.

• Reset button (2-pin RESET)

This 2-pin connector is for the chassis-mounted reset button for system reboot without turning off the system power.


10. Digital Audio connector (4-1 pin SPDIF_OUT)

This connector is for the S/PDIF audio module to allow digital sound output.

Connect one end of the S/PDIF audio cable to this connector and the other end to the S/PDIF module.

M2V-MX.SE

SPDIF_OUT

M2V-MX.SE.

Digital Audio Connector

The S/PDIF out module is purchased separately.

11. Speaker connector (4-pin SPEAKER)

This 4-pin connector is for the chasis-mounted system warning speaker. The speaker allows you to hear system beeps and warnings.

SPEAKER

1

M2V-MX.SE

M2V-MX.SE.

Speaker Out Connector

ASUS M2V-MX SE 1-31


This chapter tells how to change the system settings through the BIOS

Setup menus. Detailed descriptions of the BIOS parameters are also provided.

2-2

2.1 Managing and updating your BIOS

The following utilities allow you to manage and update the motherboard Basic

Input/Output System (BIOS) setup.

1. ASUS.EZ.Flash

(Updates the BIOS using a floppy disk, USB Flash, or the motherboard support CD during POST.)

2. ASUS AFUDOS (Updates the BIOS in DOS mode using a bootable floppy disk.)

3. ASUS.CrashFree.BIOS.2

(Updates the BIOS using a bootable floppy, or the motherboard support CD when the BIOS file fails or gets corrupted.)

4. ASUS.Update

(Updates the BIOS in Windows ® environment.)

Refer to the corresponding sections for details on these utilities.

Save a copy of the original motherboard BIOS file to a bootable floppy disk or a USB flash disk in case you need to restore the BIOS in the future. Copy the original motherboard BIOS using the ASUS Update or AFUDOS utilities.

AMI.BIOS.beep.codes

Test Item

VGA found beep

System boot

No memory found

No keyboard error

No VGA found

Hardware monitoring error

BIOS Beeps

One short beep

One short beep (Quick Boot set to Disabled)

One long beep, two short beeps, pause a period of time, and loop

One short beep

One long beep with three short beeps

One long beep with four short beeps

2.1.1 Creating a bootable floppy disk

1. Do either one of the following to create a bootable floppy disk.

DOS environment a. Insert a 1.44MB floppy disk into the drive.

b. At the DOS prompt, type format A:/S then press <Enter>.

Windows ® XP environment a. Insert a 1.44 MB floppy disk to the floppy disk drive. b. Click .Start

from the Windows ® desktop, then select My Computer.

c. Select the 3 1/2 Floppy Drive icon.

d. Click .File

from the menu, then select Format . A Format.3.1/2.Floppy.

Disk .

window appears.

e. Select Create an MS-DOS startup disk from the format options field, then click .Start

.

Chapter 2: BIOS Setup

Windows ® 2000 environment

To create a set of boot disks for Windows ® 2000: a. Insert a formatted, high density 1.44 MB floppy disk into the drive.

b. Insert the Windows ® 2000 CD to the optical drive.

c. Click .Start

, then select Run .

d. From the Open field, type

D:\bootdisk\makeboot a:

assuming that D: is your optical drive.

e. Press <Enter>, then follow screen instructions to continue.

Windows ® Vista environment a. Insert a formatted, high density 1.44 MB floppy disk to the floppy disk drive. b. Click from the Windows

1/2.Floppy

dialog box.

® desktop, then select Computer .

c. Right-click Floppy Disk Drive then click Format to display the Format.3.

d. Select the Create an MS-DOS startup disk check box.

e. Click Start .

2. Copy the original or the latest motherboard BIOS file to the bootable floppy disk.

2.1.2 ASUS EZ Flash utility

The ASUS EZ Flash feature allows you to update the BIOS without having to go through the long process of booting from a floppy disk and using a DOS-based utility. The EZ Flash utility is built-in the BIOS chip so it is accessible by pressing

<Alt> + <F2> during the Power-On Self Tests (POST).

To update the BIOS using EZ Flash:

1. Visit the ASUS website (www.asus.com) to download the latest BIOS file for the motherboard and rename the same to M2V_MX SE.ROM.

2. Save the BIOS file to a floppy disk, then restart the system.

3. Press <Alt> + <F2> during POST to display the following.

EZFlash starting BIOS update

Checking for floppy...

ASUS M2V-MX SE 2-3

2-4

4. Insert the floppy disk that contains the BIOS file to the floppy disk drive.

When the correct BIOS file is found, EZ Flash performs the BIOS update process and automatically reboots the system when done.

EZFlash starting BIOS update


Floppy found!

Reading file “M2V_MX SE.rom”. Completed.

Start erasing.......|

Start programming...|

Flashed successfully. Rebooting.

• Do not shut down or reset the system while updating the BIOS to prevent system boot failure!

• A “Floppy not found!” error message appears if there is no floppy disk in the drive. A “M2V_MX SE.ROM not found!” error message appears if the correct BIOS file is not found in the floppy disk. Make sure that you rename the BIOS file to M2V_MX SE.ROM.

2.1.3 AFUDOS utility

The AFUDOS utility allows you to update the BIOS file in DOS environment using a bootable floppy disk with the updated BIOS file. This utility also allows you to copy the current BIOS file that you can use as backup when the BIOS fails or gets corrupted during the updating process.

Copying the current BIOS

To copy the current BIOS file using the AFUDOS utility:

• Make sure that the floppy disk is not write-protected and has at least

1024KB free space to save the file.

• The succeeding BIOS screens are for reference only. The actual BIOS screen displays may not be same as shown.

1. Copy the AFUDOS utility (afudos.exe) from the motherboard support CD to the bootable floppy disk you created earlier.

2. Boot the system in DOS mode, then at the prompt type: afudos /o[filename] where the [filename] is any user-assigned filename not more than eight alphanumeric characters for the main filename and three alphanumeric characters for the extension name.


A:\>afudos /oOLDBIOS1.rom

Main filename Extension.name

3. Press <Enter>. The utility copies the current BIOS file to the floppy disk.

A:\>afudos /oOLDBIOS1.rom

AMI Firmware Update Utility - Version 1.19(ASUS V2.26(06.08.28BB)

Copyright (C) 2003 American Megatrends, Inc. All rights reserved.

Reading flash ..... done

Write to file...... ok

A:\>

The utility returns to the DOS prompt after copying the current BIOS file.

Updating the BIOS file

To update the BIOS file using the AFUDOS utility:

1. Visit the ASUS website (www.asus.com) and download the latest BIOS file for the motherboard. Save the BIOS file to a bootable floppy disk.

Write the BIOS filename on a piece of paper. You need to type the exact BIOS filename at the DOS prompt.

2. Copy the AFUDOS utility (afudos.exe) from the motherboard support CD to the bootable floppy disk you created earlier.

3. Boot the system in DOS mode, then at the prompt type: afudos /i[filename] where [filename] is the latest or the original BIOS file on the bootable floppy disk.

A:\>afudos /iM2V_MX SE.ROM

4. The utility verifies the file and starts updating the BIOS.


AMI Firmware Update Utility - Version 1.19(ASUS V2.26(06.08.28BB))


WARNING!! Do not turn off power during flash BIOS

Reading file ....... done

Reading flash ...... done

Advance Check ......

Erasing flash ...... done

Writing flash ...... 0x0008CC00 (9%)

Do not shut down or reset the system while updating the BIOS to prevent system boot failure!

ASUS M2V-MX SE 2-5

2-6

5. The utility returns to the DOS prompt after the BIOS update process is completed. Reboot the system from the hard disk drive.


AMI Firmware Update Utility - Version 1.19(ASUS V2.26(06.08.28BB)


WARNING!! Do not turn off power during flash BIOS

Reading file ....... done

Reading flash ...... done

Advance Check ......

Erasing flash ...... done

Writing flash ...... done

Verifying flash .... done

Please restart your computer

A:\>

2.1.4 ASUS CrashFree BIOS 2 utility

The ASUS CrashFree BIOS 2 is an auto recovery tool that allows you to restore the BIOS file when it fails or gets corrupted during the updating process. You can update a corrupted BIOS file using the motherboard support CD, or the floppy disk that contains the updated BIOS file.

• Prepare the motherboard support CD, or the floppy disk containing the updated motherboard BIOS before using this utility.

• Make sure that you rename the original or updated BIOS file in the floppy disk to M2V_MX SE.ROM

Recovering the BIOS from a floppy disk

To recover the BIOS from a floppy disk:

1. Turn on the system.

2. Insert the floppy disk with the original or updated BIOS file to the floppy disk drive.

3. The utility displays the following message and automatically checks the floppy disk for the original or updated BIOS file.

Bad BIOS checksum. Starting BIOS recovery...


When found, the utility reads the BIOS file and starts flashing the corrupted

BIOS file.




Floppy found!

Reading file “M2V_MX SE.ROM”. Completed.

Start flashing...

DO NOT shut down or reset the system while updating the BIOS! Doing so can cause system boot failure!

4. Restart the system after the utility completes the updating process.

Recovering the BIOS from the support CD

To recover the BIOS from the support CD:

1. Remove any floppy disk from the floppy disk drive, then turn on the system.

2. Insert the support CD to the optical drive.

3. The utility displays the following message and automatically checks the floppy disk for the original or updated BIOS file.



When no floppy disk is found, the utility automatically checks the optical drive for the original or updated BIOS file. The utility then updates the corrupted

BIOS file.



Floppy not found!

Checking for CD-ROM...

CD-ROM found!

Reading file “M2V_MX SE.ROM”. Completed.

Start flashing...

DO NOT shut down or reset the system while updating the BIOS! Doing so can cause system boot failure!

4. Restart the system after the utility completes the updating process.

The recovered BIOS may not be the latest BIOS version for this motherboard.

Visit the ASUS website (www.asus.com) to download the latest BIOS file.

ASUS M2V-MX SE 2-7

2-8

2.1.5 ASUS Update utility

The ASUS Update is a utility that allows you to manage, save, and update the motherboard BIOS in Windows to:

® environment. The ASUS Update utility allows you

•

•

•

•

•

Save the current BIOS file

Download the latest BIOS file from the Internet

Update the BIOS from an updated BIOS file

Update the BIOS directly from the Internet, and

View the BIOS version information.

This utility is available in the support CD that comes with the motherboard package.

ASUS Update requires an Internet connection either through a network or an

Internet Service Provider (ISP).

Installing.ASUS.Update

To install ASUS Update:

1. Place the support CD in the optical drive. The Drivers menu appears.

2. Click the Utilities tab, then click Install.ASUS.Update

. See page 3-4 for the

Utilities screen menu.

3. The ASUS Update utility is copied to your system.

Quit all Windows ® applications before you update the BIOS using this utility.


Updating the BIOS through the Internet

To update the BIOS through the Internet:

1. Launch the ASUS Update utility from the Windows ® desktop by clicking Start.

>.Programs.>.ASUS.>.ASUSUpdate.>.ASUSUpdate

. The ASUS Update main window appears.

2. Select Update.BIOS.from.

the.Internet

option from the drop-down menu, then click Next.

3. Select the ASUS FTP site nearest you to avoid network traffic, or click .

Auto Select . Click .Next

.

ASUS M2V-MX SE 2-9

4. From the FTP site, select the BIOS version that you wish to download.

Click Next .

5. Follow the screen instructions to complete the update process.

The ASUS Update utility is capable of updating itself through the Internet. Always update the utility to avail all its features.

Updating the BIOS through a BIOS file

To update the BIOS through a BIOS file:

1. Launch the ASUS Update utility from the Windows ® desktop by clicking Start.

>.Programs.>.ASUS.>.ASUSUpdate.>.ASUSUpdate

. The ASUS Update main window appears.

2. Select Update BIOS from a file option from the drop-down menu, then click Next .

2-10

3. Locate the BIOS file from the Open window, then click Open .

4. Follow the screen instructions to complete the update process.


2.2 BIOS setup program

This motherboard supports a programmable Serial Peripheral Interface (SPI) chip that you can update using the provided utility described in section “2.1 Managing and updating your BIOS.”

Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to “Run Setup.” This section explains how to configure your system using this utility.

Even if you are not prompted to use the Setup program, you can change the configuration of your computer in the future. For example, you can enable the security password feature or change the power management settings. This requires you to reconfigure your system using the BIOS Setup program so that the computer can recognize these changes and record them in the CMOS RAM.

The SPI chip on the motherboard stores the Setup utility. When you start up the computer, the system provides you with the opportunity to run this program. Press

<Del> during the Power-On Self-Test (POST) to enter the Setup utility; otherwise,

POST continues with its test routines.

If you wish to enter Setup after POST, reboot the system by doing any of the following procedures:

• Restart using the OS standard shut-down procedure.

• Press <Ctrl>+<Alt>+<Del> simultaneously.

• Press the reset button on the system chassis.

• Press the power button to turn the system off then back on.

Using the power button, reset button, or the <Ctrl>+<Alt>+<Del> keys to force reset from a running operating system can cause damage to your data or system. We recommend to always shut-down the system properly from the operating system.

The Setup program is designed to make it as easy to use as possible. Being a menu-driven program, it lets you scroll through the various sub-menus and make your selections from the available options using the navigation keys.

• The default BIOS settings for this motherboard apply for most conditions to ensure optimum performance. If the system becomes unstable after changing any BIOS settings, load the default settings to ensure system compatibility and stability. Select the Load Default Settings item under the

Exit Menu. See section “2.7 Exit Menu.”

• The BIOS setup screens shown in this section are for reference purposes only, and may not exactly match what you see on your screen.

• Visit the ASUS website (www.asus.com) to download the latest BIOS file for this motherboard.

ASUS M2V-MX SE 2-11

2-12

2.2.1.

BIOS menu screen

Menu items Menu bar Configuration fields General.help

System Time

System Date

Legacy Diskette A

[11:51:19]

[Thu 07/12/2007]

[1.44M, 3.5 in]

Primary IDE Master : [ST320413A]

Primary IDE Slave : [Not Detected]

Secondary IDE Master : [Not Detected]

Secondary IDE Slave : [Not Detected]

SATA1

SATA2

IDE Configuration

: [Not Detected]


System Information

Use [ENTER], [TAB] or [SHIFT-TAB] to select a field.

Use [+] or [-] to configure system time.

Sub-menu items Navigation.keys

2.2.2 Menu bar

The menu bar on top of the screen has the following main items:

Main

Advanced

Power

Boot

Exit

For changing the basic system configuration

For changing the advanced system settings

For changing the advanced power management (APM) configuration

For changing the system boot configuration

For selecting the exit options and loading default settings

To select an item on the menu bar, press the right or left arrow key on the keyboard until the desired item is highlighted.

2.2.3.

Navigation.keys

At the bottom right corner of a menu screen are the navigation keys for that particular menu. Use the navigation keys to select items in the menu and change the settings.

Some of the navigation keys differ from one screen to another.


2.2.4 Menu items

The highlighted item on the menu bar displays the specific items for that menu.

For example, selecting Main .

shows the

Main menu items.


The other items (Advanced, Power, Boot, and Exit) on the menu bar have their respective menu items.

7

Main menu items

2.2.5 Sub-menu items

An item with a sub-menu on any menu screen is distinguished by a solid triangle before the item. To display the sub-menu, select the item and press <Enter>.

2.2.6 Configuration fields

These fields show the values for the menu items. If an item is user-configurable, you may change the value of the field opposite the item. You can not select an item that is not user-configurable.

A configurable field is enclosed in brackets, and is highlighted when selected. To change the value of a field, select it then press <Enter> to display a list of options.

Refer to “2.2.7 Pop-up window.”

2.2.7 Pop-up window

Select a menu item then press <Enter> to display a pop-up window with the configuration options for that item.

2.2.8.

Scroll.bar

A scroll bar appears on the right side of a menu screen when there are items that do not fit on the screen. Press Up/Down arrow keys or PageUp/PageDown keys to display the other items on the screen.

(C)Copyright 1985-2007, American Megatrends, Inc.

2.2.9.

General.help

Pop-up window Scroll.bar

At the top right corner of the menu screen is a brief description of the selected item.

ASUS M2V-MX SE 2-13

2-14

2.3 Main menu

When you enter the BIOS Setup program, the Main menu screen appears, giving you an overview of the basic system information.

Refer to section “2.2.1 BIOS menu screen” for information on the menu screen items and how to navigate through them.

System Time

System Date

Legacy Diskette A

[11:51:19]

[Thu 07/12/2007]

[1.44M, 3.5 in]

Primary IDE Master : [ST320413A]

Primary IDE Slave : [Not Detected]

Secondary IDE Master : [Not Detected]

Secondary IDE Slave : [Not Detected]

SATA1

SATA2





Use [ENTER], [TAB] or [SHIFT-TAB] to select a field.

Use [+] or [-] to configure system time.

2.3.1 System Time [xx:xx:xx]

Allows you to set the system time.

2.3.2 System Date [Day xx/xx/xxxx]

Allows you to set the system date.

2.3.3 Legacy Diskette A [1.44M, 3.5 in.]

Sets the type of floppy drive installed.

Configuration options: [720K, 3.5 in.] [1.44M, 3.5 in.]


2.3.4.

Primary and Secondary IDE Master/Slave

While entering Setup, BIOS auto-detects the presence of IDE devices. There is a separate sub-menu for each IDE device. Select a device item then press <Enter> to display the IDE device information.

Primary IDE Master

Device : Not Detected

Type

LBA/Large Mode

Block(Multi-sector Transfer) [Auto]

PIO Mode

DMA Mode

Smart Monitoring

32Bit Data Transfer

[Auto]

[Auto]

[Auto]

[Auto]

[Auto]

[Enabled]

Select the type of device connected to the system

The values opposite the dimmed items (Device, Vendor, Size, LBA Mode, Block

Mode, PIO Mode, Async DMA, Ultra DMA, and SMART monitoring) are autodetected by BIOS and are not user-configurable. These items show N/A if no IDE device is installed in the system.

Type [Auto]

Selects the type of IDE drive. Setting to Auto allows automatic selection of the appropriate IDE device type. Select CDROM if you are specifically configuring a

CD-ROM drive. Select ARMD (ATAPI Removable Media Device) if your device is either a ZIP, LS-120, or MO drive. Configuration options: [Not Installed] [Auto]

[CDROM] [ARMD]

LBA/Large Mode [Auto]

Enables or disables the LBA mode. Setting to Auto enables the LBA mode if the device supports this mode, and if the device was not previously formatted with LBA mode disabled. Configuration options: [Disabled] [Auto]

Block (Multi-sector Transfer) [Auto]

Enables or disables data multi-sectors transfers. When set to Auto, the data transfer from and to the device occurs multiple sectors at a time if the device supports multi-sector transfer feature. When set to Disabled, the data transfer from and to the device occurs one sector at a time. Configuration options: [Disabled]

[Auto]

ASUS M2V-MX SE 2-15

PIO Mode [Auto]

Selects the PIO mode. Configuration options: [Auto] [0] [1] [2] [3] [4]

DMA Mode [Auto]

Selects the DMA mode. Configuration options: [Auto] [SWDMA0] [SWDMA1]

[SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0] [UDMA1] [UDMA2]

[UDMA3] [UDMA4] [UDMA5]

SMART Monitoring [Auto]

Sets the Smart Monitoring, Analysis, and Reporting Technology. Configuration options: [Auto] [Disabled] [Enabled]

32Bit Data Transfer [Enabled]

Enables or disables 32-bit data transfer.

Configuration options: [Disabled] [Enabled]

2-16 Chapter 2: BIOS Setup

2.3.5 SATA1 and SATA2

While entering Setup, the BIOS automatically detects the presence of Serial ATA devices. There is a separate sub-menu for each Serial ATA device. Select a device item then press <Enter> to display the Serial ATA device information.

Third IDE Master

Device : Not Detected

LBA/Large Mode

Block(Multi-sector Transfer) M

PIO Mode

DMA Mode

Smart Monitoring

32Bit Data Transfer

[Auto]

[Auto]

[Auto]

[Auto]

[Auto]

[Enabled]

The BIOS automatically detects the values opposite the dimmed items (Device,

Vendor, Size, LBA Mode, Block Mode, PIO Mode, Async DMA, Ultra DMA, and

SMART monitoring). These values are not user-configurable. These items show

Not Detected if no Serial ATA device is installed in the system.

LBA/Large Mode [Auto]

Enables or disables the LBA mode. Setting to Auto enables the LBA mode if the device supports this mode, and if the device was not previously formatted with LBA mode disabled. Configuration options: [Disabled] [Auto]

Block (Multi-sector Transfer) M [Auto]

Enables or disables data multi-sectors transfers. When set to Auto, the data transfer from and to the device occurs multiple sectors at a time if the device supports multi-sector transfer feature. When set to [Disabled], the data transfer from and to the device occurs one sector at a time. Configuration options:

[Disabled] [Auto]

PIO Mode [Auto]

Selects the PIO mode.

Configuration options: [Auto] [0] [1] [2] [3] [4]

ASUS M2V-MX SE 2-17

2-18

DMA Mode [Auto]

Selects the DMA mode. Configuration options: [Auto] [SWDMA0] [SWDMA1]

[SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0] [UDMA1] [UDMA2]

[UDMA3] [UDMA4] [UDMA5]

SMART Monitoring [Auto]

Sets the Smart Monitoring, Analysis, and Reporting Technology. Configuration options: [Auto] [Disabled] [Enabled]

32Bit Data Transfer [Disabled]

Enables or disables 32-bit data transfer.


2.3.6.


The items in this menu allow you to set or change the configurations for the IDE devices installed in the system. Select an item then press <Enter> if you wish to configure the item.


Parallel ATA IDE Controller

Hard Disk Write Protect

IDE Detect Time Out (Sec)

[Both]

[Disabled]

[35]

Parallel ATA IDE Controller [Both]

Disables or allows selection of the IDE controller. Sets to Primary to enable the primary

IDE controller only. Sets to Secondary to enable the secondary IDE controller only.

Sets to Both to enable both the primary and secondary IDE controllers. Configuration options: [Disabled] [Primary] [Secondary] [Both]

Hard Disk Write Protect [Disabled]

Disables or enables the devices write protection. This will be effective only when the device is accessed through BIOS. Configuration options: [Disabled] [Enabled]

IDE Detect Time Out [35]

Selects the time out value for detecting ATA/ATAPI devices.

Configuration options: [0] [5] [10] [15] [20] [25] [30] [35]


2.3.7.

System.Information

This menu gives you an overview of the general system specifications. The items in this menu are auto-detected by BIOS.

AMI BIOS

Version : 0115

Build Date : 06/14/07

Processor

Type : AMD Sempron(tm) Processor 3200+

Speed : 1800MHz

Count : 1

System Memory

Installed Size: 512MB

Usable Size : 348MB

AMI.BIOS

Displays the auto-detected BIOS information.

Processor

Displays the auto-detected processor information.

System.Memory

Displays the auto-detected system memory.

ASUS M2V-MX SE 2-19

2.4 Advanced menu

The Advanced menu items allow you to change the settings for the CPU and other system devices.

Take caution when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction.

USB Configuration

CPU Configuration

Chipset

Onboard Devices Configuration

PCI PnP

2-20

2.4.1 USB Configuration

The items in this menu allows you to change the USB-related features. Select an item then press <Enter> to display the configuration options.

USB Configuration

Module Version - 2.24.0-12.4

USB Devices Enabled: None

USB 1.1 Ports Configuration

USB 2.0 Ports Enable

Legacy USB Support

Port 64/60 Emulation

USB 2.0 Controller Mode

BIOS EHCI Hand-Off

[USB 8 Ports]

[Enabled]

[Enabled]

[Disabled]

[HiSpeed]

[Enabled]

The Module Version and USB Devices Enabled items show the auto-detected values. If no USB device is detected, the item shows None.


USB 1.1 Ports Configuration [USB 8 Ports]

Allows you to configure the USB ports.

Configuration options: [Disabled] [USB 2 Ports] [USB 4 Ports] [USB 6 Ports]

[USB 8 Ports]

USB 2.0 Ports Enable [Enable]

Allows you to enable or disable the USB 2.0 ports.

Configuration options: [Disabled] [Enable]

Legacy USB Support [Auto]

Allows you to enable or disable support for USB devices on legacy operating systems (OS). Setting to Auto allows the system to detect the presence of USB devices at startup. If detected, the USB controller legacy mode is enabled. If no

USB device is detected, the legacy USB support is disabled. Configuration options:

[Disabled] [Enabled] [Auto]

Port 64/60 Emulation [Enabled]

Allows you to enable or disable the Port 64/60 Emulation.Configuration options:

[Disabled] [Enabled].

USB 2.0 Controller Mode [HiSpeed]

Allows you to configure the USB 2.0 controller in HiSpeed (480 Mbps) or Full

Speed (12 Mbps). Configuration options: [HiSpeed] [Full Speed]

BIOS EHCI Hand-Off [Enabled]

Allows you to enable or disable the BIOS EHCI hand-off support.


ASUS M2V-MX SE 2-21

2-22

2.4.2 CPU Configuration

The items in this menu show the CPU-related information that the BIOS automatically detects.

Module Version:13.13

AGESA Version:02.08.07

Physical Count: 1

Logical Count: 1

Revision: F2

Cache L1: 64KB

Cache L2: 128KB

Speed : 1800MHz

Current FSB Multiplier: 9x

Maximum FSB Multiplier: 9x

Able to Change Freq. : Yes uCode Patch Level: 0x62

AMD Overclocking Configuration

Runtime Legacy PSB

Cool N’Quiet

[Enabled]

[Disabled]



Processor Frequency Multiplier [Auto]

Processor Voltage [Auto]

Processor Frequency Multiplier [Auto]

Allows you to select the processor frequency. Configuration options: [Auto]

[x5.0 1000MHz] [x6.0 1200MHz] [x7.0 1400MHz] [x8.0 1600MHz]

[x9.0 1800MHz]

Processor Voltage[Auto]

Allows you to select the processor voltage. Configuration options: [Auto]

[1.400V] [1.375V] [1.350V] [Auto]

Runtime Legacy PSB [Enabled]

Allows you to enable or disable the Runtime Legacy PSB (performance state blocks) feature necessary for implementing the AMD PowerNow! technology.


Cool N’Quiet [Disabled]

Enables or disables the AMD Cool ‘n’ Quiet! technology feature.



2.4.3.

Chipset

The items in this menu allows you to change the chipset-related features. Select an item then press <Enter> to display the configuration options.

Advanced Chipset Settings

Warning: Setting wrong values in below sections

may cause system to malfunction.

Memory Controller

AGP Bridge K8M890 AGP/PCI EXPRESS Congifuration

Southbridge VIA VT8237S Configuration

Hyper Transport Configuration

Memory.Controller

Memory Controller

Memory Configuration

ECC Configuration

Power Down Control

Memory CLK

CAS Latency(Tcl)

RAS/CAS Delay(Trcd)

Min Active RAS(Tras)

Row Precharge Time(Trp)

RAS/RAS Delay(Trrd)

Row Cycle (Trc)

Asynchronous Latency

[Auto]

:667 MHz

:5.0

:5 CLK

:15 CLK

:5 CLK

:3 CLK

:21 CLK

:6 ns

Memory Configuration

Memory Configuration

Memclock Mode

CAS Latency(CK)

TRCD

TRP [Auto]

TRAS

Command Timing (2T mode)

MCT Timing Mode

Bank Interleaving

Enable Clock to All DIMMs

MemClk Tristate C3/ATLVID

Memory Hole Remapping

[Auto]

[Auto]

[Auto]

[Auto]

[Auto]

[Auto]

[Auto]

[Disabled]

[Disabled]

[Enabled]

Memclock Mode [Auto]

Allows you to set the memory clock mode.Set by the code using

[Auto] or select [Manual] to set using one of the standard values.

Configuration options: [Auto] [Manual] [Limit]

CAS Latency (CL) [Auto]

Configuration options: [Auto] [3.0] [4.0] [5.0] [6.0]

ASUS M2V-MX SE 2-23

2-24

TRCD [Auto]

Configuration options: [Auto] [3 CLK] [4 CLK] [5 CLK] [6 CLK]

TRP [Auto]

Configuration options: [Auto] [3 CLK] [4 CLK] [5 CLK] [6 CLK]

TRAS [Auto]

Configuration options: [Auto] [5 CLK] [6 CLK] ... [18 CLK]

Command Timing 2T Mode [Auto]

Sets the 2T mode. Configuration options: [Auto] [1T] [2T]

MCT Timing Mode [Auto]

Sets the MCT Timing mode.

Configuration options: [Auto] [Manual]

The following item appears when the MCT Time Mode item is set to [Manual].

TRRD [Auto]

Configuration options: [Auto] [2T] [3T] [4T] [5T]

TRC [Auto]

Configuration options: [Auto] [11T] [12T] ... [25T]

Bank Interleacving [Auto]

Sets whether to allow memory accesses to be spread out over BANKS on the same node or across nodes, decreasing access contention.

Configuration options: [Disabled] [Auto]

Enable Clock to All DIMMs [Disabled]

Allows you to enable or disable clock to all DIMMs.


MemClk Tristate C3/ATLVID [Disabled]

Allows you to enable or disable the MemCLK Tri-Stating During C3 and Alt

VID. Configuration options: [Disabled] [Enabled]

Memory Hole Remapping [Disabled]

Allows you to enable or disable Memory Remapping around the memory hole. Configuration options: [Disabled] [Enabled]


ECC Configuration

ECC Configuration

DRAM ECC Enable

4-Bit ECC Mode

DRAM SCRUB REDIRECT

DRAM BG Srub

[Enabled]

[Disabled]

[Disabled]

[Disabled]

DRAM ECC Enable [Enabled]

Enables or disables the DRAM ECC that allows hardware to report and correct memory errors automatically to maintain system integrity.


4-Bit ECC Mode [Disabled]

Enables or disables the 4-Bit ECC mode.


DRAM SCRUB REDIRECT [Disabled]

Sets the system to correct DRAM ECC Errors immediately when they occur, even if background scrubbing is on. Configuration options: [Disabled] [Enabled]

DRAM BG Scrub [Disabled]

Disables or sets the DRAM scrubbing functionality that corrects and rewrites memory errors so later reads are correct. During this while the memory is not being used improves performance. Configuration options: [Disabled] [40ns] [80ns] [160ns] [320ns]

[640ns] [1.28us] [2.56us] [5.12us] [10.2us] [20.5us] [41.0us] [81.9us] [163.8us]

[327.7us] [655.4us]

Power Down Control [Auto]

Allows DIMMs to enter power down mode by deasserting the clock enable signal when DIMMs are not in use.

Configuration options: [Auto] [Disabled]

ASUS M2V-MX SE 2-25

2-26

AGP Bridge K8M890 AGP/PCI EXPRESS Configuration

OnChip VGA Frame Buffer Size [64MB]

Primary Graphics Adapter [PCIE VGA]

VLink Mode Supported

AGP Mode

Graphics Aperture Size

[Auto]

[AGP 8X]

[128MB]

Options for VIA AGP

Chipset

OnChip VGA Frame Buffer Size [128MB]

Sets the onchip VGA frame buffer size.

Configuration options: [Disabled] [64MB] [128MB] [256MB]

Primary Graphics Adapter [PCIE VGA]

Switches the PCI Bus scanning order while searching for a video card.

This allows you to select the type of Primary VGA in case of multiple video controllers. Configuration options: [PCI VGA] [PCIE VGA]

[Integrated VGA]

VLink Mode Supported [Auto]

Sets the VLink 8X support. Configuration options: [Auto] [Mode 0]

[Mode 1] [Mode 2] [Mode 3] [Mode 4]

AGP Mode [AGP 8X]

Allows you to change the AGP mode for the onboard VGA.

Configuration options: [AGP 8X] [AGP 4X]

Graphics Aperture Size [128MB]

Allows you to select the size of mapped memory for onboard VGA graphic data. Configuration options: [256MB] [128MB] [64MB] [32MB]

SouthBridge VIA VT8237S Configuration

SATA Controller

LAN Controller

LAN Option ROM

High Definition Audio

Front Panel Support Type

PCI Delay Transaction

[IDE]

[Enabled]

[Disabled]

[Auto]

[HD Audio]

[Enabled]

IDE

RAID

Options

SATA Controller [IDE]

Allows you to disablel or select the Serial ATA controller mode. Configuration options: [IDE] [RAID]

LAN Controller [Enabled]

Allows you to disable or enable the onboard LAN controller.



LAN Option ROM [Disabled]

Allows you to enable or disable the option ROM in the onboard LAN controller. This item appears only when the Onboard LAN item is set to

Enabled. Configuration options: [Disabled] [Enabled]

High Definition Audio [Auto]

Allows you to disable or set the high definition audio.

Configuration options: [Disabled] [Auto]

Front Panel Support Type [HD Audio]

Allows you to set the front panel audio connector (AAFP) mode to legacy

AC’97 or high-definition audio depending on the audio standard that the front panel audio module supports. Configuration options: [AC97][HD

Audio]

PCI Delay Transaction [Enabled] [Disabled]

Aloows you to enable or disable PCI delay transaction.

Hyper Transport Configuration

Hyper Transport AGP Configuration

(K8/NPT) to (AGP) Freq Auto [Enabled]

(K8/NPT) to (AGP) Freq Auto [Enabled]

Allows you to enable or disable the K8/NPT to AGP frequency selection by CPU capability. Configuration options: [Enabled] [Disabled]

ASUS M2V-MX SE 2-27

2-28

2.4.4 Onboard Devices Configuration

Congifure ITE8712F-S/KX-L Super IO Chipset

Serial Port Address

Parallel Port Address

Parallel Port Mode

Parallel Port IRQ

[3F8/IRQ4]

[378]

[Normal]

[IRQ7]

Serial Port Address [3F8/IRQ4]

Allows you to select the Serial Port1 base address.

Configuration options: [Disabled] [3F8/IRQ4] [2E8/IRQ3][3E8/IRQ4] [2E8/IRQ3]

Parallel Port Address [378]

Allows you to select the Parallel Port base addresses.

Configuration options: [Disabled] [378] [278] [3BC]

Parallel Port Mode [Normal]

Allows you to select the Parallel Port mode.

Configuration options: [Normal] [EPP] [ECP] [EPP+ECP]

Parallel Port IRQ [IRQ7]

Allows you to select the Parallel Port IRQ.

Configuration options: [IRQ5] [IRQ7]


2.4.5.

PCI.PnP

The PCI PnP menu items allow you to change the advanced settings for PCI/PnP devices. The menu includes setting IRQ and DMA channel resources for either

PCI/PnP or legacy ISA devices, and setting the memory size block for legacy ISA devices.

Take caution when changing the settings of the PCI PnP menu items. Incorrect field values can cause the system to malfunction.

Advanced PCI/PnP Settings

WARNING: Setting wrong values in below sections may cause system to malfunction.

Plug And Play O/S

PCI Latency Timer

Allocate IRQ to PCI VGA

Palette Snooping

IRQ-3 assigned to









[No]

[64]

[Yes]

[Disabled]

[PCI Device]

[PCI Device]

[PCI Device]

[PCI Device]

[PCI Device]

[PCI Device]

[PCI Device]

[PCI Device]

[PCI Device]

NO: Lets the BIOS configure all the devices in the system.

YES: Lets the operating system configure Plug and Play (PnP) devices not required for boot if your system has a

Plug and Play operating system.

Plug and Play O/S [No]

When set to [No], BIOS configures all the devices in the system. When set to

[Yes] and if you installed a Plug & Play operating system, the operating system configures the Plug & Play devices not required for boot. Configuration options:

[No] [Yes]

PCI Latency Timer [64]

Allows you to select the value in units of PCI clocks for the PCI device latency timer register. Configuration options: [32] [64] [96] [128] [160] [192] [224] [248]

Allocate IRQ to PCI VGA [Yes]

When set to [Yes], BIOS assigns an IRQ to PCI VGA card if the card requests for an IRQ. When set to [No], BIOS does not assign an IRQ to the PCI VGA card even if requested. Configuration options: [Yes] [No]

Palette Snooping [Disabled]

When set to [Enabled], the pallete snooping feature informs the PCI devices that an ISA graphics device is installed in the system so that the latter can function correctly. Setting to [Disabled] deactivates this feature. Configuration options:

[Disabled] [Enabled]

IRQ xx [Available]

When set to [Available], the specific IRQ is free for PCI/PnP devices to use. When set to [Reserved], the IRQ is reserved for legacy ISA devices. Configuration options: [Available] [Reserved]

ASUS M2V-MX SE 2-29

2-30

2.5 Power menu

The Power menu items allow you to change the settings for the Advanced Power

Management (APM) feature. Select an item then press <Enter> to display the configuration options.

Suspend Mode

ACPI Version Support

ACPI APIC Support

APM Configuration

Hardware Monitor

[Auto]

[ACPI v2.0]

[Enabled]

Select the ACPI state used for System

Suspend.

2.5.1 Suspend Mode [Auto]

Allows you to select the ACPI state to be used for system suspend. Configuration options: [S1 (POS) Only] [S3 Only] [Auto]

2.5.2 ACPI Version Support [ACPI v2.0]

Allows you to add more tables for Advanced Configuration and Power Interface

(ACPI) specifications. Configuration options: [ACPI v1.0] [ACPI v2.0]

[ACPI v3.0]

2.5.3 ACPI APIC Support [Enabled]

Enables or disables the ACPI support in the ASIC. When set to Enabled, the ACPI

APIC table pointer is included in the RSDT pointer list. Configuration options:

[Disabled] [Enabled]


2.5.4 APM Configuration

APM Configuration

Power Management/APM [Enabled]

Restore on AC Power Loss [Power Off]

Advanced Resume Events Controls

Power On By Ring

Power On By Lan

Power On by PME

Power On By KBC

Wake-Up Key

Power On By PS/2 Mouse

Power On By RTC Alarm

[Disabled]

[Disabled]

[Disabled]

[Disabled]

[Any Key]

[Disabled]

[Disabled]

Power Management/APM [Enabled]

Allows you to enable or disable the Advanced Power Management (APM) feature.


Restore on AC Power Loss [Power Off ]

When set to Power Off, the system goes into off state after an AC power loss.

When set to Power On, the system goes on after an AC power loss. When set to

Last State, the system goes into either off or on state whatever the system state before the AC power loss.

Configuration options: [Power Off] [Power On] [Last State]

Power On By Ring [Disabled]

This allows either settings of [Enabled] or [Disabled] for powering up the computer when the external modem receives a call while the computer is in Soft-off mode.


The computer cannot receive or transmit data until the computer and applications are fully running. Thus, connection cannot be made on the first try. Turning an external modem off and then back on while the computer is off causes an initialization string that turns the system power on.

Power On By LAN [Disabled]

When set to [Enabled], this parameter allows you to turn on the system through a

PCI LAN or modem card. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead. Configuration options: [Disabled] [Enabled]

ASUS M2V-MX SE 2-31

2-32

Power On By PME [Disabled]

When this item is set to [Enabled]. A PME (Power Management Event) can turn on the system. Configuration Options: [Disabled] [Enabled]

Power On By KBC [Disabled]

Allows you to use specific keys on the keyboard to turn on the system. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead.


The following item is active when the Power On By KBC item is set to [Enabled].

Wake-Up Key [Any Key]

Allows you to assign a key to resume the system. When this item is set to

[Specific key], it allows you to set wake-up password.

Configuration Options: [Any Key] [Specific Key]

Power On By PS/2 Mouse [Disabled]

When set to [Enabled], this parameter allows you to use the PS/2 mouse to resume the system. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead. Configuration options: [Disabled] [Enabled]

Power On By RTC Alarm [Disabled]

Allows you to enable or disable RTC to generate a wake event. When this item is set to Enabled, the items RTC Alarm Date, RTC Alarm Hour, RTC Alarm Minute, and RTC Alarm Second appear with set values. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead.



2.5.5 Hardware Monitor

Hardware Monitor

CPU Temperature

MB Temperature

CPU Fan Speed

Chassis Fan Speed

VCORE Voltage

3.3V Voltage

5V Voltage

12V Voltage

Smart Q-Fan Function

[43ºC/93ºF]

[35ºC/95ºF]

[3308RPM]

[N/A]

[ 1.504V]

[ 3.360V]

[ 5.160V]

[11.328V]

[Disabled]

CPU Temperature

CPU Temperature [xxx ºC/xxx ºF] or [Ignored]

MB Temperature [xxx ºC/xxx ºF] or [Ignored]

The onboard hardware monitor automatically detects and displays the CPU, motherboard and power temperatures. Select Ignored if you do not wish to display the detected temperatures.

CPU Fan Speed [xxxxRPM] or [Ignored]

The onboard hardware monitor automatically detects and displays the CPU fan speed in rotations per minute (RPM). If the fan is not connected to the chassis, the specific field shows N/A. Select Ignored if you do not wish to display the detected speed.

Chassis Fan Speed [xxxxRPM] or [N/A] or [Ignored]

The onboard hardware monitor automatically detects and displays the chassis fan speed in rotations per minute (RPM). If the fan is not connected to the chassis, the specific field shows N/A. Select Ignored if you do not wish to display the detected speed.

VCORE Voltage, +3.3V Voltage, +5V Voltage, +12V Voltage

The onboard hardware monitor automatically detects the voltage output through the onboard voltage regulators.

Smart Q-Fan function [Disabled]

Allows you to enable or disable the smart Q-fan control function. When this field is set to [Enabled], the item Fan Auto Mode .

items .

appear.


Fan Auto Mode Start Voltage, Start Speed Temp, Full Speed Temp

Sets the smart fan mode.

ASUS M2V-MX SE 2-33

2-34

2.6 Boot menu

The Boot menu items allow you to change the system boot options. Select an item then press <Enter> to display the sub-menu.

Boot Settings

Boot Device Priority

Boot Settings Configuration

Security

Specifies the Boot

Device Priority sequence.

2.6.1 Boot Device Priority

Boot Device Priority

1st Boot Device

2nd Boot Device

3rd Boot Device

[1st FLOPPY DRIVE]

[Hard Drive]

[ATAPI CD-ROM]

Specifies the boot sequence from the available devices.

A device enclosed in parenthesis has been disabled in the corresponding type menu.

1st ~ xxth Boot Device [1st Floppy Drive]

Select Screen

Select Item

+- Change Option

F1 General Help

F10 Save and Exit

These items specify the boot device priority sequence from the available devices.

The number of device items that appear on the screen depends on the the number of devices installed in the system.

Configuration options: [xxxxx Drive] [ATAPI CD-ROM] [Disabled]


2.6.2 Boot Settings Configuration

Boot Settings Configuration

Quick Boot

Full Screen Logo

Bootup Num-Lock

Wait for ‘F1’ If Error

[Enabled]

[Enabled]

[On]

[Enabled]

Allows BIOS to skip certain tests while booting. This will decrease the time needed to boot the system.

Quick Boot [Enabled]

Select Screen

Select Item


F1 General Help


ESC Exit

Enabling this item allows the BIOS to skip some Power On Self Tests (POST) while booting to decrease the time needed to boot the system. When set to [Disabled],

BIOS performs all the POST items. Configuration options: [Disabled] [Enabled]

Full Screen Logo [Enabled]

Allows you to enable or disable the full screen logo display feature. Configuration options: [Disabled] [Enabled]

Make sure that the above item is set to [Enabled] if you want to use the ASUS

MyLogo™ feature.

Bootup Num-Lock [On]

Allows you to select the power-on state for the NumLock.

Configuration options: [Off] [On]

Wait for ‘F1’ If Error [Enabled]

When set to Enabled, the system waits for F1 key to be pressed when error occurs. Configuration options: [Disabled] [Enabled]

ASUS M2V-MX SE 2-35

2-36

2.6.3 Security

The Security menu items allow you to change the system security settings. Select an item then press <Enter> .

to display the configuration options.

Security Settings

Supervisor Password : Not Installed

User Password : Not Installed

Change Supervisor Password

Change User Password

<Enter> to change password.

<Enter> again to disable password.


Select this item to set or change the supervisor password. The Supervisor

Password item on top of the screen shows the default Not.Installed

. After you have set a password, this item shows Installed .

Select Screen

Select Item


F1 General Help


ESC Exit

To set a Supervisor Password:

1. Select the Change Supervisor Password item and press <Enter> .

2. From the password box, type a password combination of at least six (6) letters and/or numbers, then press <Enter>.

3. Confirm the password when prompted.

The message “Password Installed” appears after you have successfully set your password.

The Supervisor Password item now shows Installed .

To change the supervisor password, follow the same steps as in setting a user password.

To clear the supervisor password, select the Change Supervisor Password then press <Enter>. The message “Password Uninstalled” appears.

If you forget your BIOS password, you can clear clear it by erasing the CMOS

Real Time Clock (RTC) RAM. See section “1.9 Jumpers” for information on how to erase the RTC RAM.


After you have set a supervisor password, the other items appear to allow you to change other security settings.


Supervisor Password : Installed



User Access Level


Password Check

[Full Access]

[Setup]

<Enter> to change password.

<Enter> again to disabled password.

User Access Level (Full Access]

Select Screen

Select Item


F1 General Help


ESC Exit

Allows you to select the access restriction to the Setup items. Configuration options: [No Access] [View Only] [Limited] [Full Access]

No.Access

prevents user access to the Setup utility.

View.Only.

allows access but does not allow change to any field.

Limited.

allows change only to selected fields, such as Date and Time.

Full Access allows viewing and changing all the fields in the Setup utility.

Change.User.Password

Select this item to set or change the user password. The User Password item on top of the screen shows the default Not.Installed

. After you have set a password, this item shows Installed.

To set a User Password:

1. Select the Change User Password item and press <Enter>.

2. On the password box that appears, type a password combination of at least six

(6) letters and/or numbers, then press <Enter>.


The message “Password Installed” appears after you have successfully set your password.

The User Password item now shows Installed .

ASUS M2V-MX SE 2-37

After you have set a supervisor password, the other items appear to allow you to change other security settings.

2-38


Supervisor Password : Not Installed



User Access Level


Password Check

[Full Access]

[Setup]

User Access Level [Full Access]

Select Screen

Select Item


F1 General Help


This item allows you to select the access restriction to the Setup items.

Configuration options: [No Access] [View Only] [Limited] [Full Access]

No Access prevents user access to the Setup utility.

View Only allows access but does not allow change to any field.

Limited allows changes only to selected fields, such as Date and Time.

Full Access allows viewing and changing all the fields in the Setup utility.

Change.User.Password

Select this item to set or change the user password. The User Password item on top of the screen shows the default Not Installed. After you set a password, this item shows Installed.

To set a User Password:

1. Select the Change User Password item and press <Enter>.

2. On the password box that appears, type a password composed of at least six letters and/or numbers, then press <Enter>.


The message “Password Installed” appears after you set your password successfully.

To change the user password, follow the same steps as in setting a user password.

Clear.User.Password

Select this item to clear the user password.

Password Check [Setup]

When set to [Setup], BIOS checks for user password when accessing the Setup utility. When set to [Always], BIOS checks for user password both when accessing

Setup and booting the system.

Configuration options: [Setup] [Always]


2.7 Exit menu

The Exit menu items allow you to load the optimal or failsafe default values for the

BIOS items, and save or discard your changes to the BIOS items.

Exit Options

Exit & Save Changes

Exit & Discard Changes

Discard Changes

Load Setup Defaults

Exit system setup after saving the changes.

F10 key can be used for this operation.

Pressing <Esc> does not immediately exit this menu. Select one of the options from this menu or <F10> from the legend bar to exit.

Exit.&.Save.Changes

Once you are finished making your selections, choose this option from the Exit menu to ensure that the values you selected are saved to the

CMOS RAM. An onboard backup battery sustains the CMOS RAM and stays on even when the PC is turned off. When you select this option, a confirmation window appears. Select Yes to save changes and exit.

If you attempt to exit the Setup program without saving your changes, the program prompts you with a message asking if you want to save your changes before exiting. Press <Enter> to save the changes while exiting.

Exit & Discard Changes

Select this option only if you do not want to save the changes that you made to the Setup program. If you made changes to fields other than System Date, System

Time, and Password, the BIOS asks for a confirmation before exiting.

ASUS M2V-MX SE 2-39

Discard Changes

Allows you to discard the selections you made and restore the previously saved values. After selecting this option, a confirmation appears. Select Yes to discard any changes and load the previously saved values.

Load Setup Defaults

This option allows you to load the default values for each of the parameters on the

Setup menus. When you select this option or if you press <F5>, a confirmation window appears. Select Yes.

to load default values. Select Exit.Saving.Changes

or make other changes before saving the values to the non-volatile RAM.

2-40 Chapter 2: BIOS Setup

This chapter describes the contents of the support CD that comes with the motherboard package.

3

support

3.1 Installing an operating system

This motherboard supports Windows ® 2000/XP/Vista and Windows ® XP/Vista

64-bit operating systems (OS). Always install the latest OS version and corresponding updates to maximize the features of your hardware.

• Motherboard settings and hardware options vary. Use the setup procedures presented in this chapter for reference only. Refer to your OS documentation for detailed information.

• Make sure that you install Windows ® 2000 Service Pack 4 or the Windows ®

XP Service Pack 1 or later versions before installing the drivers for better compatibility and system stability.

3.2 Support CD information

The support CD that came with the motherboard package contains the drivers, software applications, and utilities that you can install to avail all motherboard features.

The contents of the support CD are subject to change at any time without notice. Visit the ASUS website (www.asus.com) for updates.

3.2.1 Running the support CD

Place the support CD to the optical drive. The CD automatically displays the

Drivers menu if Autorun is enabled in your computer.

Click.an.icon.to.display.

support CD/motherboard information

3-2

Click.an.item.to.install

If Autorun is NOT enabled in your computer, browse the contents of the support

CD to locate the file ASSETUP.EXE from the BIN folder. Double-click the

ASSETUP.EXE to run the CD.

Chapter 3: Software support

3.2.2 Drivers menu

The drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to activate the devices.

ASUS InstAll-Drivers Installation Wizard

Installs the ASUS InstAll-Drivers Installation Wizard.

AMD Cool ‘n’ Quiet Driver

Installs the AMD Cool ‘n’ Quiet driver.

VIA Chipset Driver Program

Installs the VIA Chipset Driver Program.

VIA S3G Display Driver

Installs the VIA S3G display driver.

Realtek Audio Driver

Installs the Realtek ® audio driver.

Atheros F2 Ethernet Driver

Installs the Atheros F2 Ethernet Driver.

The screen display and drivers option may not be the same for different operating system versions.

ASUS M2V-MX SE 3-3

3.2.3 Utilities menu

The Utilities menu shows the applications and other software that the motherboard supports.

3-4

ASUS InstAll-Installation Wizard for Utilities

Install the ASUS InstAll-Installation Wizard.

ASUS Cool ‘n’ Quiet Utility

Installs the ASUS Cool ‘n’ Quiet utility.

ASUS.PC.Probe.II

This smart utility monitors the fan speed, CPU temperature, and system voltages, and alerts you of any detected problems. This utility helps you keep your computer in healthy operating condition.

ASUS.Update.

The ASUS Update utility allows you to update the motherboard BIOS in a

Windows ® environment. This utility requires an Internet connection either through a network or an Internet Service Provider (ISP).

Chapter 3: Software support

Install the following utilities from the ASUS Superb Software Library CD if needed..

ADOBE Acrobat Reader V7.0

Installs the Adobe

®

Acrobat

®

Reader that allows you to open, view, and print documents in Portable Document Format (PDF).

Microsoft DirectX 9.0c

Installs the Microsoft

®

DirectX 9.0c driver. The Microsoft DirectX

®

9.0c is a multimedia technology that enhances computer graphics and sound.

DirectX

®

improves the multimedia features of you computer so you can enjoy watching TV and movies, capturing videos, or playing games in your computer. Visit the Microsoft

®

website (www.microsoft.com) for updates.

Symantec Norton Internet Security

Installs Symantec Norton Internet Security application.

WinDVD Copy5 Trial

Installs the WinDVD Copy5 trial version.

Corel Snapfire Plus SE

Installs Corel Snapfire Plus SE.

ASUS M2V-MX SE 3-5

3.2.4 Make Disk menu

The Make Disk menu allows you to make a RAID driver disk.

VIA 32/64 bit RAID Driver

Allows you to create a VIA ® 32/64 bit RAID driver disk.

3-6 Chapter 3: Software support

3.2.5 Manual menu

The Manual menu contains the user manuals for third party components. Click an item to open the folder of the user manual.

VIA VT8237 RAID User’s Manual

Allows you to open VIA ® VT8237 RAID user’s manual.

Realtek HD Audio User’s Manual

Allows you to open Realtek HD Audio user’s manual.

The user manual files are in Portable Document Format (PDF). Install the Adobe Acrobat Reader application from the Utilities tab before opening a user manual file.

ASUS M2V-MX SE 3-7

3.2.6.

ASUS.Contact.information

Click the Contact tab to display the ASUS contact information. You can also find this information on the inside front cover of this user guide.

3-8 Chapter 3: Software support

Asus M2V-MX SE Motherboard User Manual

Contents

Chapter.1:.

Product introduction .

Contents

Chapter.2:.

BIOS setu p

Contents

Chapter.3:.

Software support .

Notices

Federal Communications Commission Statement

Canadian Department of Communications Statement

Safety information

Electrical.safety

Operation.safety

M2V-MX SE specifications summary

M2V-MX SE specifications summary

introduction

1.1 Welcome!

1.2 Package contents

1.3 Special features

1.3.1 Product highlights

Latest.processor.technology..

.

.

AMD Cool ‘n’ Quiet Technology ..

DDR2 800MHz memory support .....

PCI.Express™.interface..

USB.2.0.technology.

.

10/100.Mbps.LAN

1.3.2 Innovative ASUS features

ASUS.EZ.Flash..

.

CrashFree.BIOS.2.

.

ASUS Q-Fan technology .

ASUS.MyLogo™.

C.P.R. (CPU Parameter Recall)

Fanless Design

1.4 Before you proceed

Onboard LED

1.5 Motherboard overview

1.5.1 Motherboard layout

Place six (6) screws into the holes indicated by circles to secure the motherboard to the chassis.

1.6 Central Processing Unit (CPU)

1.6.1. Installing.the.CPU

1.7 System memory

1.7.2 Memory configurations

1.7.3 DDR2 Qualified Vendors List

DDR2 533 Qualified Vendors List

DDR2 667 Qualified Vendors List

DDR2 667 Qualified Vendors List

DDR2 800 Qualified Vendors List

1.7.3 Installing a DIMM

1.7.4 Removing a DIMM

1.8 Expansion slots

1.8.2 Configuring an

Standard.

interrupt assignments

IRQ assignments for this motherboard

1.9 Jumpers

1.10 Connectors

1.10.1 Rear panel connectors

LAN port LED indications

Audio 2, 4, or 6-channel configuration

2.1 Managing and updating your BIOS

AMI.BIOS.beep.codes

2.1.1 Creating a bootable floppy disk

2.1.2 ASUS EZ Flash utility

2.1.3 AFUDOS utility

Copying the current BIOS

Updating the BIOS file

2.1.4 ASUS CrashFree BIOS 2 utility

Recovering the BIOS from a floppy disk

Recovering the BIOS from the support CD

2.1.5 ASUS Update utility

Installing.ASUS.Update

Updating the BIOS through the Internet