Below you will find brief information for Dryer C-Series 30Lb, 50Lb, 80L. This manual covers installation, operating instructions, programming, service procedures, troubleshooting, and parts data for the Dexter Commercial Vended Dryer C-Series, available in 30Lb, 50Lb, and 80L single tumbler configurations. It includes safety warnings, specifications, and maintenance guidelines. It also describes several features of the dryer, including its solid-state ignition system and programming capabilities. The manual includes information on electrical and gas requirements, and exhaust installation.
Advertisement
Advertisement
Starting Serial Number Part # 8533-088-001 7/21
2
Indicates an imminently hazardous situation, which if not avoided, will result in death or serious injury.
Indicates a potentially hazardous situation, which if not avoided could result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Minor burns, pinch points that result in bruises and minor chemical irritation.
Indicates information or a company policy that relates directly or indirectly to the safety of personnel or protection of property.
This is the user caution symbol. It indicates a condition where damage to the equipment resulting in injury to the operator could occur if operational procedures are not followed. TO REDUCE THE RISK OF DAMAGE OR
INJURY, refer to accompanying documents; follow all steps or procedures as instructed.
This is the electrical hazard symbol. It indicates that there are DANGEROUS HIGH VOLTAGES PRESENT inside the enclosure of this product. TO REDUCE THE RISK OF
FIRE OR ELECTRIC SHOCK, do not attempt to open the enclosure or gain access to areas where you are not instructed to do so. REFER SERVICING TO QUALIFIED
SERVICE PERSONEL ONLY
Caution! There are sharp edges on various sheet metal parts internal to the enclosure. Use safety consciousness when placing or moving your hands while working in the interior of this equipment.
Caution! To reduce the risk of damage to the Water Inlet
Valve, do not supply inlet water with a temperature that exceeds 70˚ C.
Caution! To reduce the risk of fire or explosion, do not operate this equipment in any hazardous classified
(ATEX) environment.
Part # 8533-088-001 7/21
Warning! Do not operate equipment if door glass is damaged in any way.
Warning! Keep clear of rotating parts.
Prohibited! Do not enter this equipment or space.
Prohibited! Do not step or stand on this equipment.
Prohibited! Do not operate without all guards and covers in place.
Prohibited! Do not operate without all guards and covers in place.
Prohibited! Do not wash or Dry clothing impregnated with flammable liquids (petrochemical).
Prohibited! Do not allow children to play in or around equipment.
Part # 8533-088-001 7/21
3
Indicates an imminently hazardous situation, which if not avoided, will result in death or serious injury.
Indicates a potentially hazardous situation, which if not avoided could result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Minor burns, pinch points that result in bruises and minor chemical irritation.
Indicates information or a company policy that relates directly or indirectly to the safety of personnel or protection of property.
This is the user caution symbol. It indicates a condition where damage to the equipment resulting in injury to the operator could occur if operational procedures are not followed.
TO REDUCE THE RISK OF DAMAGE OR INJURY, refer to accompanying documents; follow all steps or procedures as instructed.
This is the electrical hazard symbol. It indicates that there are DANGEROUS HIGH VOLTAGES
PRESENT inside the enclosure of this product.
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, do not attempt to open the enclosure or gain access to areas where you are not instructed to do so. REFER SERVICING TO QUALIFIED
SERVICE PERSONEL ONLY
do not operate this equipment in any hazardous
4
Part # 8533-088-001 7/21
• All Dryers must be installed in accordance to all applicable electrical, plumbing and all other local codes.
• These installation and operation instructions are
and electrical shock, do not perform any servicing other than that contained in the installation and op-
Do not install Equipment in an explosive atmosphere.
•Care must be stressed with all foundation work to ensure a stable unit installation, eliminating possibilities of excessive vibration.
•Foundation must be level within 13 mm to ensure proper washer operation.
Do not operate washer or Dryer if door glass is damaged in any way.
mable liquids (petrochemical).
Part # 8533-088-001 7/21
5
Children should be supervised to ensure they do not operate or play in or around equipment.
Keep all panels in place to protect against electrical shock and injury and add rigidity to washer.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety .
A washer should not be allowed to operate if any of the following occur:
•
•
•
•
Excessive high water level.
Machine is not connected to a properly earthed circuit.
Door does not remain securely locked during the entire cycle.
Vibration or shaking from an inadequate mounting or foundation
6
Part # 8533-088-001 7/21
Warning! Do not operate equipment if door glass is damaged in any way.
Warning! Keep clear of rotating parts.
Prohibited! Do not enter this equipment or space.
Prohibited! Do not step or stand on this equipment.
Prohibited! Do not operate without all guards and covers in place.
Prohibited! Do not operate without all guards and covers in place.
Prohibited! Do not wash or Dry clothing impreg-
Prohibited! Do not allow children to play in or around equipment.
Part # 8533-088-001 7/21
7
Prohibited! Do not attempt to open, touch, or proceed before referring to the manual or unless quali-
Mandatory! Read all supporting documentation before operating or maintaining equipment.
Mandatory! Disconnect power before servicing equipment.
Mandatory! Lock out and tag out before servicing this equipment.
Mandatory! Children should be supervised to ensure they do not operate equipment.
8
Part # 8533-088-001 7/21
These washers are equipped with devices and features relating to their safe operation. To avoid injury or electrical shock, do not perform and service, unless qualified to do so.
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or loss of life.
IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch: do not use any telephone in your building.
• Clear the room, building or area of all occupants.
• Imm.ediately call your gas supplier from a neighbor’s telephone.
• Follow the gas supplier’s instructions.
Section 1: Specifications & Installation
Specifications, Mounting Dimensions
Specifications. & Dimensions 30Lb............12 & 13
Specifications. & Dimensions 50Lb............14 & 15
Specifications. & Dimensions 80Lb............16 & 17
Dryer Installation & Clearences .......................
18
Dryer Make up air ..........................................
19
Electrical Requirements.............................19 & 20
Gas Requirements...............................................20
Exhaust Installation ...............................
20 & 21
Dryer Ignition & Testing .................................
22
Section 2:Operating Instructions
Dryer Operating Instructions .........................
27
Section 3:
Dryer Programming Instructions
DexterLive setup & programing USB .........
30-39
Dryer Programming ...................................40-53
Section 4:
Dryer Service,Toubleshooting and Schematics
Dryer Service Procedures..............................56-65
Dryer Troubleshooting Tips ........................66-68
Dryer Schematics & Diagrams60hz ........
70 & 71
• If you cannot reach your gas supplier, call the fire department. Installation and service must be performed by a qualified installer, service agency or the gas supplier.
Section 5:
Dryer Parts Data .....................................74-105
Dry only fabrics washed in water to avoid the risk of fire, including spontaneous combustions, do not dry:
• Items containing foam rubber, or any similarly textured rubber-like materials.
• Any items on which you have used a cleaning solvent or which contain flamm.able liquids or solids, such as naptha, gasoline, or other oils or waxes.
Section 6:
Maintenance
Dryer........................................................108
To activate your warranty, be sure to return your red warranty form to the factory. Please have serial number and model ready when calling for assistance.
Part # 8533-088-001 7/21
9
10
Part # 8533-088-001 7/21
Part # 8533-088-001 7/21
11
30 lb. Commercial Dryer: T-30 – DC0030NB-10EC1X (60 Hz), DC0030NB-
39AC1X (50 Hz)
Cabinet Height 72 1/4”
(Assumes minimum leveling leg adjustment)
Cabinet Width
Overall Depth
Floor to Door Center
Door Opening
31 1/2”
42”
41 1/4”
22 5/8”
30 lbs.
30”
27 1/2”
11.25 cu. ft.
Dry Wt. Capacity
Cylinder Diameter
Cylinder Depth
Cylinder Volume
Lint Screen Area
Gas Input (60 hz)
Gas Input (50 hz)
Gas Supply Connection
Natural Gas Supply (Water Column)
Natural Burner Manifold
515 sq. in.
90,000 Btu/hr
72,000 Btu/hr
1/2”
5-8”
3 1/2”
11 ½ -14” L.P. Supply (Water Column)
L.P. Burner Manifold
Exhaust Size
Make-up Air
11”
8”
1.0 sq. ft.
Example: 1.0 sq. ft = 1 ft. long X 1 ft. wide
Motor Size
Airflow (60 hz)
Airflow (50 hz)
1/2 H.P.
830 CFM
690 CFM
Electrical Specifications - 120/60/1
Voltage/Hz/Phase 120V/60Hz/1Phase
Running Amps
Circuit Protection Amps
Wire Size
Electrical Service
9.6
15
12 gauge
2 wire + ground
Electrical Specifications - 220-240/50/1
Voltage/Hz/Phase 220-240V/50Hz/1Phase
Running Amps
Circuit Protection Amps
Wire Size
Electrical Service
5.1
10
14 gauge
2 wire + ground
Shipping Weight
Net Weight 463 lbs. 210 kg.
Clearance Behind Machines (min.)
507 lbs.
18”
1835 mm.
800 mm.
1067 mm.
1048 mm.
575 mm.
13.6 kg.
762 mm.
699 mm.
319 liters
3323 sq. cm.
26.4 kW
21.1 kW
12.7 mm.
127 mm. - 203 mm.
88.9 mm.
292 mm. - 356 mm.
279 mm.
203 mm.
929 sq. cm.
.373 kW
23.5 m^3/min
19.5 m^3/min
231 kg.
457 mm.
12
Part # 8533-088-001 7/21
Part # 8533-088-001 7/21
13
50 lb. Commercial Dryer: T-50 – DC0050NB-10EC1X (60 Hz), DC0050NB-
39AC1X (50 Hz)
Cabinet Height 72 1/4”
(Assumes minimum leveling leg adjustment)
Cabinet Width
Overall Depth
L.P. Supply (Water Column)
L.P. Burner Manifold
Exhaust Size
Make-up Air
Motor Size (60 Hz)
Motor Size (50 Hz)
Airflow (60 hz)
Airflow (50 hz)
Floor to Door Center
Door Opening
Dry Wt. Capacity
Cylinder Diameter
Cylinder Depth
Cylinder Volume
Lint Screen Area
Gas Input (60 hz)
Gas Input (50 hz)
Gas Supply Connection
Example: 1.25 sq. ft = 1.25 ft. long X 1 ft. wide
Natural Gas Supply (Water Column)
Natural Burner Manifold
34 1/2”
48”
41”
25 5/8”
50 lbs.
32.5”
33”
15.84 cu. ft.
1.25 sq. ft.
875 mm.
1219 mm.
1041 mm.
653 mm.
24.9 kg.
826 mm.
845 mm.
449.5 liters
708 sq. in. 4568 sq. cm.
145,000 Btu/hr 42.5 kW
120,000 Btu/hr 35.2 kW
1/2”
5-8”
3 1/2”
11 ½ -14”
11”
8”
1 H.P.
3/4 H.P.
910 CFM
760 CFM
1835 mm.
12.7 mm.
127 mm. - 203 mm.
88.9 mm.
292 mm. - 356 mm.
279 mm.
203 mm.
1161 sq. cm.
.746 kW
.560 kW
25.8 m^3/min
21.5 m^3/min
Electrical Specifications - 120/60/1
Voltage/Hz/Phase 120V/60Hz/1Phase
Running Amps
Circuit Protection Amps
Wire Size
Electrical Service
9.6
15
12 gauge
2 wire + ground
Electrical Specifications - 220-240/50/1
Voltage/Hz/Phase 220-240V/50Hz/1Phase
Running Amps
Circuit Protection Amps
Wire Size
Electrical Service
5.1
10
14 gauge
2 wire + ground
Shipping Weight
Net Weight
Clearance Behind Machines (min.)
611 lbs.
579 lbs.
18”
277 kg.
263 kg.
457 mm
14
Part # 8533-088-001 7/21
Part # 8533-088-001 7/21
15
80 lb. Commercial Dryer: T-80 – DC0080NB-10EC1X (60 Hz), DC0080NB-
39AC1X (50 Hz)
Cabinet Height 75 3/4”
(Assumes minimum leveling leg adjustment)
Cabinet Width
Overall Depth
L.P. Supply (Water Column)
L.P. Burner Manifold
Exhaust Size
Make-up Air
Motor Size (60 Hz)
Motor Size (50 Hz)
Airflow (60 hz)
Airflow (50 hz)
Floor to Door Center
Door Opening
Dry Wt. Capacity
Cylinder Diameter
Cylinder Depth
Cylinder Volume
Lint Screen Area
Gas Input (60 hz)
Gas Input (50 hz)
Gas Supply Connection
Example: 1.5 sq. ft = 1.5 ft. long X 1 ft. wide
Natural Gas Supply (Water Column)
Natural Burner Manifold
38 3/8”
51 3/4”
43”
25 5/8”
80 lbs.
36.5”
38”
23.0 cu. ft.
1.5 sq. ft.
975 mm.
1315 mm.
1092 mm.
653 mm.
36.3 kg.
927 mm.
965 mm.
651.3 liters
823 sq. in. 5310 sq. cm.
215,000 Btu/hr 63.0 kW
195,000 Btu/hr 57.1 kW
1/2”
5-8”
3 1/2”
11 ½ -14”
11”
8”
1 H.P.
3/4 H.P.
1200 CFM
1000 CFM
1924 mm.
12.7 mm.
127 mm. - 203 mm.
88.9 mm.
292 mm. - 356 mm.
279 mm.
203 mm.
1394 sq. cm.
.746 kW
.560 kW
34.0 m^3/min
28.3 m^3/min
Electrical Specifications - 120/60/1
Voltage/Hz/Phase 120V/60Hz/1Phase
Running Amps
Circuit Protection Amps
Wire Size
Electrical Service
10.4
15
12 gauge
2 wire + ground
Electrical Specifications - 220-240/50/1
Voltage/Hz/Phase 220-240V/50Hz/1Phase
Running Amps
Circuit Protection Amps
Wire Size
Electrical Service
5.2
10
14 gauge
2 wire + ground
Shipping Weight
Net Weight
Clearance Behind Machines (min.)
729 lbs.
699 lbs.
18”
331.2 kg.
291.2 kg.
457 mm.
16
Part # 8533-088-001 7/21
Part # 8533-088-001 7/21
17
All commercial dryer installations must conform with local applicable local codes or in the absence of local codes, with the National Fuel Gas Code ANSI Z223.1A-1988. Canadian installations must comply with current standard CAN/CGA-B149(.1 or .2) Installation Code for Gas Burning Appliances or Equipment, and local codes if applicable. The appliance, when installed, must be electrically grounded in accordance with the National Electric Code, ANSI/NFPA No. 70-1990,or when installed in Canada, with Standard CSA C22.1
Canadian Electrical Code Part 1.
Installation Clearances:
This unit may be installed at the following alcove clearances. (millimeters)
1. Left side- 0”
2. Right side- 0” *
3. Back-
4. Front-
5. Top-
18” (457) (Certified for 1” (25) clearance; however, 18” (457) clearance is neces sary behind the belt guard to allow servicing and maintenance.)
48” (1220) (to allow use of dryer)
Refer to figure labelled “Vertical Clearance Dimensions”.
6. Floor-
Certification allows 0” clearance at the top 1” (25) back from the front. However, a
1/4” (6)clearance is required to allow opening the upper service door.
A 10” (254) clearance is required from the top at all other points.
This unit may be installed upon a combustible floor.
*Units may be installed in direct contact with an adjacent dryer, providing
allowance is made for opening upper and lower service doors.
Do not obstruct the flow of combustion and ventilation air.
Maintain minimum of 1” (25) clearance between duct and combustible material.
18
VERTICAL CLEARANCE DIMENSIONS - ALL DCBD(30/50/80)
Part # 8533-088-001 7/21
MAKE-UP AIR
Adequate make-up air must be supplied to replace air exhausted by dryers on all types of installations. Provide a minimum make-up air opening to the outside for each dryer as follows:
Dryer Model
DC0030NC-10EC1X
Make-up Air Volume/Time Make-up Air Opening Area (minimum)
830 CFM (23.5 m3/minute) 1 ft² (0.10 m2)
DC0030NC-39AC1X 690 CFM (19.5 m3/minute) 1 ft² (0.10 m2)
DC0050NC-10EC1X 910 CFM (25.8 m3/minute) 1.25 ft² (0.12 m2)
DC0050NC-39AC1X 760 CFM (21.5m3/minute) 1.25 ft² (0.12 m2)
DC0080NC-10EC1X 1200 CFM (34.0 m3/minute) 1.5 ft² (0.14 m2)
DC0080NC-39AC1X 1000 CFM (28.3 m3/minute) 1.5 ft² (0.14 m2)
This is a net requirement of effective area. Screens, grills or louvers, which will restrict the flow of air, must be considered. Consult the supplier to determine the free area equivalent for the grill being used.
The source of make-up air should be located sufficiently away from the dryers to allow an even airflow to the airintakes of all dryers. Multiple openings should be provided.
NOTE: The following considerations must be observed for gas dryer installations where dry cleaners are installed. The sources of all make-up air and room ventilation air movement to all dryers must be located away from any dry cleaners. This is necessary so that solvent vapors will not be drawn into the dryer inlet ducts. Dry cleaner solvent vapors will decompose in contact with an open flame such as the gas flame present in clothes dryers. The decomposition products are highly corrosive and will cause damage to the dryer(s), ducts and clothes loads.
ELECTRICAL REQUIREMENTS .
The electrical power requirements necessary to operate the unit satisfactorily are listed on the serial plate located on the back panel of each dryer. The electrical connection should be made to the termi nal block in the rear control box assembly on the rear of the unit, using a wire size adequate to handle the amperage and voltage listed on the serial plate, but never smaller than No.12 AWG wire. It is absolutely necessary that the dryer be grounded to a known ground.
Individual circuit breakers for each unit are recommended. The wiring diagram is located on the belt guard onthe back of the machine.
TRANSIENT VOLTAGE SURGE SUPPRESSORS
Like most electrical equipment your new machine can be damaged or have its life shortened by voltage surges due to lightning strikes which are not covered by factory warranty. Local power distribution problems also can be detrimental to the life of electrical components. We recommend the installation of transient voltage surge suppressors for your new equipment. These devices may be placed at the power supply panel for the complete installation and don’t require and individual device for each machine.
These surge protectors help to protect equipment from large spikes and also from small ongoing spikes in the power that occur on a day to day basis. These smaller surges can shorten overall life of electrical components of all types and cause their failure at a later date. Although they can’t protect against all events, these protective devices have a good reputation for significantly lengthening the useful life of electronic components.
Electronic Components are helped to have a longer useful life when they are supplied with the clean stable electrical power they like.
We are including the following names and links to a few suppliers of these devices for those who don’t currenty have a source.
Part # 8533-088-001 7/21
19
TVSS
MANUFACTURERS
Innovative Technology, Inc
CONTACT
(Eaton) Factory
PHONE
1-800-647-8877 or www.itvss.com
EFI Electronics Corporation
(Schneider Electric)
Factory 1-800-877-1174 or www.efinet.com
Distributor – Surge Pro 1-877-233-0153
Factory 1-800-851-1508 or www.mcgsurge.com
MCG Surge Protection
Advanced Protection
Technologies Inc. Factory 1-800-237-4567 or www.aptsurge.com
GAS REQUIREMENTS .
The complete gas requirements necessary to operate the dryer satisfactorily are listed on the serial plate located on the back panel of the dryer and in the specifications section of this manual. The inlet gas connection to the unit is 1/2-inch pipe thread for T-30 and T-50 and 3/4-inch for
T-80. However, the size of the piping to supply the dryer should be determined by reference to the Na tional Fuel Gas Code ANSI Z223.1A and consultation with the local gas supplier. An individual gas shutoff valve is recommended for each dryer and may be required by local code (not supplied). A joint compound resistant to the action of liquefied petroleum gases should be employed in making pipe connections. A 1/8inch NPT plugged tapping, accessible for test gage connection, must be installed immediately upstream of the gas supply connection to the dryer. A drip tee is provided in the unit gas piping to catch dirt and other foreign articles. All pipe connections should be checked for leakage with soap solution. Never check with an open flame. For altitudes above 2,000 feet (610m), it is necessary to derate the BTU input. Contact your local distributor for instructions. L.P. gas conversion kits are available for this dryer. Contact your local distributor.
CAUTION: The dryer must be disconnected from the gas supply piping system during any pressure testing of that system. Do not expose the dryer’s gas control valve to testing pressure.
Burner Set-Up
All gas burner manifolds should be checked for proper gas pressure while burning. Dryer manafold pressure should be set at 3.5 W.C. for Natural Gas while burner operating.
EXHAUST INSTALLATION.
(Refer to Figure 2 at the end of section 6.) Exhausting of the dryer(s) should be planned and constructed so that no air restrictions occur. Any restriction due to pipe size or type of installation can cause slow drying time, excessive heat, and lint in the room.
From an operational standpoint, incorrect or inadequate exhausting can cause a cycling of the high limit thermostat which shuts off the main burners and results in inefficient drying.
Individual exhausting of the dryers is recommended. All heat, moisture, and lint should be ex hausted outside by attaching a pipe of the proper diameter to the dryer adapter collar and extending it out through an outside wall.
This pipe must be very smooth on the inside, as rough surfaces tend to collect lint which will eventually clog the duct and prevent the dryer from exhausting properly. All elbows must be smooth on the inside. All joints must be made so the exhaust end of one pipe is inside the next one downstream. The addition of an exhaust pipe tends to reduce the amount of air the blower can exhaust. This does not affect the dryer operation if held within practical limits. For the most efficient operation, it is recommended that no more than 20’ (6m) of straight 8” diameter pipe be used with two right angle elbows. When more than two elbows are used, 2’ (600mm) of straight pipe should be removed for each additional elbow. No more than four right angle elbows should be used to exhaust a dryer.
Maintain minimum 1” (25) clearance between duct and combustible material.
20
Part # 8533-088-001 7/21
If the exhaust pipe passes through a wall, a metal sleeve of slightly larger diameter should be set in the wall and the exhaust pipe passed through this sleeve. This practice is required by some local codes and is recommended in all cases to protect the wall. This type of installation should have a means provid ed to prevent rain and high winds from entering the exhaust when the dryer is not in use. A hood with a hinged damper can be used for this purpose. Another method would be to point the outlet end of the pipe downward to prevent entrance of wind and rain. In either case, the outlet should be kept clear, by at least
24” (610), of any objects which would cause an air restriction.
Never install a protective screen over the exhaust outlet. When exhausting a dryer straight up through a roof, the overall length of the duct has the same limits as exhausting through a wall. A rain cap must be placed on top of the exhaust and must be of such a type as to be free from clogging. The type using a cone shaped “roof” over the pipe is suitable for this application.
Exhausting the dryer into a chimney or under a building is not permitted. In either case there is a danger of lint build-up which can be highly combustible.
Installation of several dryers, where a main discharge duct is necessary, will need the following considerations for installation (see Fig. 2). Individual 8” (200mm) ducts from the dryers into the main discharge duct should be at a 45 degree angle in the direction of discharge air flow.
NOTE: Never install the individual 8” ducts at a right angle into the main discharge duct. The individual ducts from the dryers can enter at the sides or bottom of the main discharge duct. Fig ure 2 indicates the various round main duct diameter to use with the individual dryer ducts. The main duct can be rectangular or round, provided adequate air flow is maintained. For each individual dryer, the total exhausting (main discharge duct plus duct outlet from the dryer) should not exceed the equivalent of 20 feet (6m) and two elbows. The diameter of the main discharge duct at the last dryer must be maintained to exhaust end.
NOTE : A small diameter duct will restrict air flow; a large diameter duct will reduce air velocity – both contributing to lint build up. An inspection door should be provided for periodic clean-out of the main duct.
NOTE: STATIC BACK PRESSURE should be a maximum of 0.3 in. w.c (7.6 mm w.c) at the rear exhaust outlet of the dryer. If multiple dryers are connected to the common duct, ensure the back draft damper is installed properly.
NOTE: The following illustration shows the various round main duct diameters to use with the individual dryer ducts. The main duct can be rectangular or round, provided adequate air flow is maintained. For each individual cylinder the total exhausting (main discharge duct plus duct outlet from the dryer) should not exceed the equivalent of 14 feet and two elbows. The diameter of the main discharge duct at the last dryer must be maintained to exhaust end.
Part # 8533-088-001 7/21
21
DRYER IGNITION (SOLID STATE IGNITION).
The solid state ignition system lights the main burner gas by spark. The gas is ignited and burns only when the gas-valve relay (in the electronic controller) calls for heat. The procedure for first-time starting of a dryer is as follows:
A. First, review and comply with the “WARNINGS ABOUT USE AND OPERATION” found on the inside front cover of this manual. Be sure the electrical power supply is connected correctly. The white (neutral) wire is to be connected to the N terminal while the black (line) wire to the L1 terminal of the terminal block in the rear control box. The dryer MUST be properly grounded.
B. Make sure all gas supply lines are purged of air. Close the main gas shut-off valve and wait for five minutes before turning the valve back on.
C. Turn on main electrical power switch. The dryer may be started by following the “OPERATING
INSTRUCTIONS” found later in this manual.
D. Natural gas and liquefied petroleum gas fired dryers both operate in the same manner. When gas-valve relay contacts are closed (indicating a demand for heat), the solid state ignition control will automatically supply energy to the redundant gas valve. Spark will continue until a flame is detected by the sensing probe, but not longer than 10 seconds. If the gas fails to ignite within 10 seconds, the gas will shut off for 15 seconds. The control will attempt to ignite two more times in a similar manner. If the gas fails to ignite after three tries, the gas valve closes and the system will "lock out". No further attempts at ignition will be performed automatically. It is then necessary to interrupt electrical power to the ignition system before making another attempt to light the burners.
This can be done by opening the dryer door, allowing the dryer to come to a stop for 15 seconds, closing the door, and pushing the "Start" button. The dryer will then repeat the ignition trial cycle.
DRYER SHUTDOWN
To render the dryer inoperative, turn off the main gas shut-off valve and disconnect electrical power to the dryer.
IT IS RECOMMENDED THAT THE INSTALLER TEST THE DRYER FOR OPERATION AND
INSTRUCT THE USER BEFORE LEAVING THE INSTALLATION.
22
Part # 8533-088-001 7/21
Part # 8533-088-001 7/21
23
24
Part # 8533-088-001 7/21
Part # 8533-088-001 7/21
25
OPERATING INSTRUCTIONS
STARTING THE DRYER
1. The display on the dryer control will show the required vend amount when in idle mode. Once the door is opened it will prompt the user to add money.
Load clothes into the dryer. Close the door completely.
2. Deposit coins equal to or greater than the displayed vend price. The display on the control will prompt the user to choose a drying temperature.
3. Select the drying temperature by pressing the appropriate button for “high”,
“med” (medium) or “low”. This will turn on the red indicator light showing the selected temperature.
4. Press the “start” button to start dryer. This will turn on the green indicator
Light. The drying time purchased is now displayed. The colon begins flashing to indicate that the timer is counting down.
Display
Buttons
26
Part # 8533-088-001 7/21
RUNNING THE DRYER
-Opening the door will stop the dryer, but the timer will continue to count down.
The dryer will restart, if time has not expired, upon closing the door and pressing the “start” button.
-Selected temperature may be changed at any time (unless Temperature Pricing feature is activated).
-Running time may be extended by depositing coins and pressing the “start” but ton. Unless time has expired, the controller will accept coins whether or not the original vend price is equaled.
-If time has run out, the dryer must be restarted as if it was at the beginning of drying the load, which requires meeting or exceeding the vend price.
-Clothes should be removed promptly after the cycle is completed to prevent ex cessive wrinkling.
-Cool-down time (owner programmable) is always part of the cycle time pur chased by the customer. For example, if the cool-down time is 2 minutes, then the last 2 minutes of the cycle will have no heat.
Part # 8533-088-001 7/21
27
28
Part # 8533-088-001 7/21
Part # 8533-088-001 7/21
29
DexterLive
The new DexterLive controls were created for you to be able to interface easier with your equipment and create variable pricing cycles to increase your profitibility in the same floor space.
First, log into DexterLive, create your location and equipment list and then create your cycle and pricing information by the particular type of washer and dryer at the location.
Once the information is saved, download the “AllUser.xml” file to a USB device which will be used to program the machines from the USB port.
Keep it simple or use the marketing features such as temperture pricing, plus cycle or an additional final rinse that the customer can select for a value added wash. Utilize time of day pricing to help move people from heavy use periods to special value times of day or days of the week.
Through the easy to use USB programing so you can download all special pricing and
<RXU6PDUW1HZ%XVLQHVV3DUWQHU
30
Accessible
Available anytime, anywhere, on any internet capable device. Once you have set up your free account all of your custom settings and store information are saved making it quick and easy to make future changes.
/RJLQWR'H[WHU/LYH
View and customize equipment settings to fit your business model. Download your unique user file and quickly transfer it to your equipment via USB.
Profitable
Create exciting promotions to attract new customers. Offer extra prewash, plus cycles, Extra rinse and temperature pricing to drive more revenue in your store.
Part # 8533-088-001 7/21
/RJLQ
First Time Creating an Account at Dexter Live
1) Log into DexterLive
At the bottom, select “Create your DexterLive account.”
DexterLive gives an owner the ability to manage multiple locations.
2) At the “Create a DexterLive Account” screen.
A.
First time users must create an account.
An account must be created to use the DexterLive features.
Part # 8533-088-001 7/21
31
B.
Fill in the required fields and click on “Create My Account”.
When creating a new user account make sure to fill in all fields marked with asterisks and check the
“Terms of
Service” box.
C.
After selecting to “Create My Account”, you will see the log in screen advising you to go to your e-mail and activate your account.
After creating your account you will need to use the email link to gain first access. The account will not be active until you confirm your account.
32
Part # 8533-088-001 7/21
3) Open the e-mail sent from Dexterlive and select “CONFIRM MY ACCOUNT”
Selecting the
“Confirm My
Account” hyperlink will take you back to the DexterLive log in page.
4) At the “Log into DexterLive” screen, enter your e-mail/user name and password to access
DexterLive.
Welcome to
DexterLive.
Proceed to the step to create your location information.
Part # 8533-088-001 7/21
33
Programming
5) To configure your settings with DexterLive.com:
A.
Add or select a location to program.
DexterLive gives an owner the ability to manage multiple locations and machines.
B.
On the left side of the screen, select the “Programming” tab.
Follow instructions in the programming tab.
34
Part # 8533-088-001 7/21
C.
Edit the “General Settings” (Equipment Tab)
Adjust setting and offset time to match your location.
(Time is set for
Central
Standard Time)
D.
Next select the “+Add Equipment” (Equipment Tab), located in the upper right hand corner.
Name of the machine.
(Example:
Dryer 1)
Enter serial number and machine type then select
“Save and
Continue.”
Part # 8533-088-001 7/21
35
E.
When all of the equipment has been added, select “Edit” on the machine type you wish to modify, and then select “Pricing”. (Equipment Tab and Machine Settings Tab)
Program the price of the machine and the extra pricing adders.
F.
Cycle changes can be made by selecting the “Cycles” tab.
Adjust cycle programming set the length of time and extracts speed as needed.
36
Part # 8533-088-001 7/21
G.
If desired, you may create and edit optional store promotions from the
“Promotions “Tab.
Select “Save
Promotion” once your changes have been made.
6) Create and download the Programming File.
A.
Once all preferred prices, cycles and promotions have been modified and saved,
select
Part # 8533-088-001 7/21
37
-Cool-down time (owner programmable) is always part of the cycle time purchased by the customer. For example, if the cool-down time is 2 minutes, then the last 2 minutes of the cycle will have no heat.
B.
7) To enter the manual programming mode, the upper service door on the dryer must be unlocked and lifted to reveal the back side of the control. The programming button is found in the location shown below. The programming button is then pressed for 1 second. The control should display “DRYER PROGRAMMING”.
See the figure below for the location of the programming button on the dryer control. Please note, this is the
Note:
The dryer control can be programmed to prompt the user for alternate vend prices, change dryer cycle times,
1.
2.
Based on your internet browser the file needs to be saved as “AllUser.xml”. Depending on your Internet browser you may need to retrieve the file from your “Downloads” folder, which is located under “Computer”. please contact your local Dexter distributor.
Note: The newly created programing file may have changed from the proper “AllUser.xml Ma chine programming will not occur using a different file name than “AllUser.xml”. Any extra extension names will require the file to be renamed back to “AllUser.xml” for the machine to recognize the file.
To save the Programming File to a USB Drive:
A.
B.
Move or Copy the “AllUser.xml” file from your computer onto a USB drive.
Based on your computer and internet browser, this file may be found in your “Down loads” folder, which is located under the “Computer” area.
The “AllUser.xml” file size is small, nearly any capacity USB drive will do.
Program
Button
8) Program Your Machines Using the USB Drive
8514-234-001 rev. A page 14 CAUTION!!! Be sure that any loose keys or other items that are connected to the USB de- vice are removed from the USB stick to prevent any possible metal contact with the control board.
A.
Insert the USB drive containing the “AllUser.xml” file into the Dexter machines you wish to program. The control will scroll “…………” while identifying the program on the USB. Once identified, the display will scroll “INSTALL USER FILE FROM USB”. At this prompt press the green start button on the front panel.
38
Part # 8533-088-001 7/21
B.
The machine will scroll “TO INSTALL – PRESS START”. At this prompt, press the green “Start” again.
C.
Once the program is uploaded successfully the control will scroll “DONE REMOVE
USB”. The USB drive can be safely removed at this point.
Note: All Dexter equipment (washers and dryers) featuring DexterLive controls can be programmed using this file once the equipment has been configured.
Part # 8533-088-001 7/21
39
-Cool-down time (owner programmable) is always part of the cycle time purchased by the customer. For example, if the cool-down time is 2 minutes, then the last 2 minutes of the cycle will have no heat.
PROGRAMMING THE DRYER CONTROL
The dryer control can be programmed to prompt the user for alternate vend prices, change dryer cycle times, temperatures and many other options. This can be accomplished in two ways:
dryer.
2. USB download of a customizable User File. For instructions on using the USB download feature,
MANUAL PROGRAMMING:
The dryer must be in idle mode for the manual programming menus to be accessed. Idle mode is when the dryer is not actively running a drying cycle and the vend price is displayed on the screen (for both upper and lower dryers).
To enter the manual programming mode, the control tray on the dryer must be unlocked and pulled out to reveal the programming button. The programming button is then pressed for 1 second. The control should display “DRYER PROGRAMMING”.
please contact your local Dexter distributor or visit DexterLive.com.
1.
Manual programming utilizing the “Start”, “High”, “Medium” and “Low” buttons.
2.
USB download of a pre-programmed User File. For instructions on using the USB download feature, please contact your local Dexter distributor.
MANUAL PROGRAMMING:
The dryer must be in idle mode for the manual programming menus to be accessed. Idle mode is when the dryer is not actively running a drying cycle and the vend price is displayed on the screen.
To enter the manual programming mode, the upper service door on the dryer must be unlocked and lifted to reveal the back side of the control. The programming button is found in the location shown below. The programming button is then pressed for 1 second. The control should display “DRYER PROGRAMMING”.
See the figure below for the location of the programming button on the control tray.
See the figure below for the location of the programming button on the dryer control. Please note, this is the control as viewed from the underside of the lifted service door.
Program
Button
40
8514-234-001 rev. A page 14
Part # 8533-088-001 7/21
When manual programming mode is entered, the “Start”, “High”, “Medium” and “Low” buttons for the lower dryer perform alternate functions. Please note that the changes made using the lower dryer buttons affect both upper and lower dryers.
Button Name
Start
High
Medium
Low
Alternate Function in Programming Mode
Becomes the action to accept the displayed option or the “Enter” key
Becomes the action to move UP through displayed options (Press & hold for accelerated scrolling)
Becomes the action to move DOWN through displayed options (Press & hold for accelerated scrolling)
Becomes the action to move back a step (1 press) or EXIT from programming mode (press for 3 seconds)
Part # 8533-088-001 7/21
41
These alternate functions allow the user to move through a menu of options to choose various programmable settings. The figure below shows the top level menu. Choosing an option from the top level menu will then display the next level of options (the sub menu).
Quick Test Option:
When the Quick Test Option is chosen, the dryer will begin a shortened dry cycle without the displayed vend price being met. The purpose of this shortened cycle is to test all major components for proper opera tion.
Error Codes should all function normally during this test. The display will show customer prompts in a simi lar way to a normal dry cycle.
42
Part # 8533-088-001 7/21
Continuous Test Option:
Similar to the Quick Test, when the Continuous Test Option is chosen, the dryer will begin a dry cycle without the displayed vend price being met. However, in this case, it will be a continuously-running cycle. It will not time out after any designated amount of time.
CAUTION: This option is meant for factory use only. Do not operate the dryer with this cycle active without factory authorization.
Error Code Historical Log:
The last five occurring error codes will be stored in the control with a time and date stamp. The purpose of this option is only to observe the history of these code occurrences (no changes can be made).
The time is based off the Real Time Clock, but potentially shifted by the user’s manual programming chang es (Shift Hours option) and/or network time override. As additional error codes occur, the oldest of the five logged codes is cleared from memory.
Prices Option:
This option allows the user to set values for coin acceptor inputs, vend price & time and extend dry price & time. It also allows the user to return the values to factory defaults. After changing prices using the “Up” or
“Down” buttons, the “Enter” button must be pressed again for the control to store the changes that have been made. Note that, in general, time values are set in 1 minute increments. This can be changed to 30 second increments, by changing the “Display Time” to “MIN+SEC” (refer to the “Settings” section”).
1. “RIGHT COIN” and “LEFT COIN” are the two possible inputs from coin acceptors.
2. “PRICE SET VEND” is the actual Base Vend Price (or Vend Price A) that is shown on the control display. The value can be increased or reduced even down to “0”. In this case, the displays will prompt “FREE” and the cycle will start as soon is the “Start’ button is pressed (without any vend price being met).
3. “TIME SET VEND” is the cycle time that the customer has available once they’ve met the Base
Vend Price.
4. “FREE SET TIME” is the cycle time that the customer has available if the Base Vend Price is set to
“FREE”.
5. “EXTEND DRY” sets the price and time for additional drying time that becomes available after the customer has already met the Base Vend Price.
To reset either the coin acceptor inputs or the vend price to factory default, press “Enter” when the “DE -
FAULT” prompt is shown. Press “Enter” again when the “RESET” prompt is shown to confirm the action.
Example- A store owner has programmed the control for the following values:
Base Vend Price
Base Vend Time
Extend Dry Price
Extend Dry Price
$1.00
30 minutes
$.25
8 minutes
In this case, the customer adds 4 quarters to satisfy the $1.00 Vend Price. The display shows 30 minutes of drying time. At this point, if an additional quarter is added, the customer display shows an additional 8 minutes of drying time (38 minutes total) as per the Extend Dry Price & Time.
The customer starts the drying cycle and at 25 minutes into the cycle (13 minutes displayed), they add an additional quarter. The controller adds 8 minutes to the displayed time again (21 minutes total) as per the
Extend Dry Price & Time.
“AFTER CYCLE” allows the user to choose whether a customer is allowed to add “EXTEND DRY” time for up to 30 seconds after the dryer door is opened after a completed cycle.
Part # 8533-088-001 7/21
43
Prices Option:
This option allows the user to set values for coin acceptor inputs, vend price & time and extend dry price & time. It also allows the user to return the values to factory defaults. After changing prices using the “Up” or
“Down” buttons, the “Enter” button must be pressed again for the control to store the changes that have been made. Note that, in general, time values are set in 1 minute increments. This can be changed to 30 second increments, by changing the “Display Time” to “MIN+SEC” (refer to the “Settings” section”).
1. “RIGHT COIN” and “LEFT COIN” are the two possible inputs from coin acceptors.
2. “PRICE SET VEND” is the actual Base Vend Price (or Vend Price A) that is shown on the control display. The value can be increased or reduced even down to “0”. In this case, the displays will prompt “FREE” and the cycle will start as soon is the “Start’ button is pressed (without any vend price being met).
3. “TIME SET VEND” is the cycle time that the customer has available once they’ve met the Base
Vend Price.
4. “FREE SET TIME” is the cycle time that the customer has available if the Base Vend Price is set to
“FREE”.
5. “EXTEND DRY” sets the price and time for additional drying time that becomes available after the customer has already met the Base Vend Price.
To reset either the coin acceptor inputs or the vend price to factory default, press “Enter” when the “DE -
FAULT” prompt is shown. Press “Enter” again when the “RESET” prompt is shown to confirm the action.
Example- A store owner has programmed the control for the following values:
Base Vend Price
Base Vend Time
Extend Dry Price
Extend Dry Price
$1.00
30 minutes
$.25
8 minutes
In this case, the customer adds 4 quarters to satisfy the $1.00 Vend Price. The display shows 30 minutes of drying time. At this point, if an additional quarter is added, the customer display shows an additional 8 minutes of drying time (38 minutes total) as per the Extend Dry Price & Time.
The customer starts the drying cycle and at 25 minutes into the cycle (13 minutes displayed), they add an additional quarter. The controller adds 8 minutes to the displayed time again (21 minutes total) as per the
Extend Dry Price & Time.
“AFTER CYCLE” allows the user to choose whether a customer is allowed to add “EXTEND DRY” time for up to 30 seconds after the dryer door is opened after a completed cycle.
44
Part # 8533-088-001 7/21
The figure below shows the sub menu options for Prices:
Part # 8533-088-001 7/21
45
Cycles Option:
This option allows the user to set temperature and cooldown information for the drying cycle. It also al lows the user to return the values to factory defaults.
1. “TEMP SETTINGS” allows the user to make adjustments, within a designated range, to the cycling temperature for each of the “Low”, “Medium” and “High” customer choices.
2. In addition, on the “Low” setting, the user can reduce the cycling temperature below 110 degrees F. In this case, when the customer chooses the “Low” setting, the dryer
will not turn on the gas valve. When checked, the displayed temperature will read
“NO HEAT”.
3. “COOLDOWN” allows the user to change the designated time at the end of a cycle where the gas valve relay is turned off. On “High” and “Medium” temperature settings, the designated time cannot be reduced to less than 2 minutes.
4. “DEFAULT TEMP” allows the user to choose which general temperature setting, “High”, “Me dium” or “Low”, the control will default to at the beginning of each cycle if the customer does not make a choice.
5. “ANTI WRINKLE” is a feature that periodically rotates the dryers after a cycle is complete. If the door was closed at the end of the cycle, and is left closed for 5 minutes, the enuncia tor will sound and the display begins scrolling “ANTI WRINKLE”. 5 seconds later, the dryer motor will turn on for 60 seconds and then turn off. The gas valves will not be turned on. The “ANTI WRINKLE” message will continue throughout the time that the motor is turned on. The user can choose to enable or disable this feature.
To reset all values in the Cycles option to factory default, press “Enter” when the “DEFAULT” prompt is shown. Press “Enter” again when the “RESET” prompt is shown to confirm the action.
46
Part # 8533-088-001 7/21
Part # 8533-088-001 7/21
47
Temperature Pricing Option:
This option allows the user to require additional vend amounts be added based on the drying temperature chosen by the customer. This pricing adder is effective only for the Base Vend Price (it does not affect the
Extend Dry Price). It allows a pricing adder separate for “Medium” and “Hot” temperature settings.
Example- A store owner has programmed the control for the following:
Vend Price
Vend Time
Extend Dry Price
Medium Adder
Hot Adder
$1.00
30 minutes
8 minutes
$.25
$.50
In this case, the Vend Price is displayed as:
$1.00 if Low Temperature is chosen
$1.25 if Medium Temperature is chosen
$1.50 if Hot Temperature is chosen
When Temperature Pricing Adders are in place (user has chosen a higher value then $0.00), if the customer attempts to change their temperature selection from a lower temperature to a higher one during a drying cycle, there will be no change in the temperature selection. The higher temperature buttons are disabled until the drying cycle is complete and a new Vend Price is required.
The figure below shows the sub menu options for Temperature Pricing:
The figure below shows the sub menu options for Temperature Pricing:
48
Part # 8533-088-001 7/21
Settings Options:
The Settings options allow for the user to make various programming changes to change how the control operation affects the customer. See below for detailed information on each next level option.
1. “Decimal Point”: If the user programs the Decimal Point to “OFF”, control display will not show a decimal point on any vend price values. The factory default is “ON”.
2. “Display Time”: If the user programs this value to “MIN”, then minutes only will be shown for the cycle time. If it is programmed to “MIN+SEC”, then minutes and seconds will be shown.
This also allows other programming changes, involving time, to be made in either minute increments or minutes & seconds increments, as desired.
3. “Temp Scale”: If the user programs this value to “F”, then the temperatures will be displayed in
Fahrenheit units. If it is programmed to “C”, then the temperature will be in Celsius units.
4. “Sounds”: If the user programs the Sounds to “OFF”, the control will not sound the enunciator at the end of a dry cycle. The factory default is “ON”.
5. “Password”: If the user programs the password to any value other then 0000, the control will prompt the user to enter a password (the programmed value) before manual programming can be accessed. The factory default is “0000” (no password).
a. Note that if the user forgets the Password, it can be reset to factory default (no pass word), by performing a hard reset on the control. Please refer to the appropriate section of this manual to understand how to perform a hard reset.
b. The individual digits of the Password can be set by using the “Up” or “Down” buttons to change the number that is flashing. Once the desired number is chosen for a single digit, press the “Enter” button to move to the next one.
Once all four desired digits are chosen, the “Enter” button must be held down for 3 seconds to confirm that the complete password should be set.
6. “Central Pay”: If the user programs this value to “ON”, the left and right coin inputs become up per and lower dryer coin inputs.
Central Pay “OFF”
Left Coin Input
Right Coin Input
Central Pay “ON”
Upper Dryer Input
Lower Dryer Input
A system can then be installed that will register coin inputs per individual dryer remotely from a Central Pay kiosk. The left and right coin prices must be appropriately programmed. When this option is enabled, the controller will only display customer prompts for a designated dryer. This designated dryer is determined when coins are inserted at the Central Pay kiosk.
7. “Language”: The control uses English for the default language of the customer prompts. Al ternatively, the user can choose Spanish or French for the customer display prompts.
However, all other prompts, such as Manual Programming, USB Programming and any Error
Codes will still display in English.
Part # 8533-088-001 7/21
49
8. “Shift Hours”: This feature allows the user to shift the time used by the control from the time kept internally by the control. The control uses a Real Time Clock (RTC) to internally track the time and date. The RTC continues operation even if the control loses external power.
The RTC is set for Central Standard Time and no daylight savings. Because the machine may be located in another time zone, the user can choose to create an alternate time & date that tracks in parallel to the RTC. When this alternate time is chosen, or shifted from the RTC, the alternate time will be used to, for example, track error code occurrences and set time-of-day pricing changes.
a. The hours in “SHIFT HOURS” can be set by using the “Up” or “Down” buttons to change the number that is flashing. Once the desired hour shift is chosen, press the “En ter” button to move to the minutes. Once the hours and minute shift are both chosen, the “Enter” button must be held down for 3 seconds to confirm that the complete shifted time is set.
9. “Time”: The control uses a Real Time Clock (RTC) to internally track the time and date. The RTC continues operation even if the control loses external power. The RTC is set for Central
Standard Time and no daylight savings. However, if a problem occurs and the RTC time is not accurate, it can be reset to the current time using this option.
a. The hours in “TIME” can be set by using the “Up” or “Down” buttons to change the number that is flashing. Once the desired hour is chosen, press the “Enter” button to move to the minutes. Once the hours and minute are both chosen, the
“Enter” button must be held down for 3 seconds to confirm that RTC is meant to be reset to the complete entry.
10. “Date”: Similar to “Time”, if a problem occurs and the RTC date is not accurate, it can be reset to the current date using this option.
a. The day of the month in “DATE” can be set by using the “Up” or “Down” buttons to change the number that is flashing. Once the desired day of the month is chosen, press the “Enter” button to move to the month of the year. Once the de sired month of the year is chosen, press the “Enter” button to move to the year. Once the day, month and year are all chosen, the “Enter” button must be the “RESET” prompt is shown to confirm the action.
held down for 3 seconds to confirm that RTC is meant to be reset to the complete entry. To reset all values in the Settings options to factory default, press “Enter” when the “DEFAULT” prompt is shown. Press “Enter” again when
50
Part # 8533-088-001 7/21
The figure below shows the sub menu options for Settings:
Part # 8533-088-001 7/21
51
Usage Menu:
The Usage menu allows for the user to track data about machine usage. See below for detailed information on each sub menu option.
1. “Coin Audit”: The coin audit field shows the accumulation of coin pulses that were sent to the control over each of the left and right coin inputs. Note that this is a count of coin pulses, not an accumulated report of vend value.
a. The user can also return the coin audit amounts to the factory default setting (zero). To reset all coin audit values, press “Enter” when the “DEFAULT” prompt is shown.
Press “Enter” again when the “RESET” prompt is shown to confirm the action.
2. “Motor Hours”: The motor hours field shows the accumulated hours of operation for both the upper and lower motors independently. In many cases, it will match the cycle hours of the machine. However, separate fields are provided in the event that a motor is replaced on a machine. The user can set the motor hours to a designated number. For example, if it is necessary to replace the control on a machine, the new control could be programmed to show the motor hours that were recorded by the previously installed control. The individual digits of the hours count can be set by using the “Up” or “Down” buttons to change the number that is flashing. Once the desired digit of the hours is chosen, press the “Enter” button to move to the next digit. Once the complete hours are chosen, the “Enter” button must be held down for 3 seconds to confirm the action.
a. The user can also return the motor hours to the factory default setting (zero). To reset the motor hours, press “Enter” when the “DEFAULT” prompt is shown. Press “En ter” again when the “RESET” prompt is shown to confirm the action.
3. “Cycle Hours”: The cycle hours field shows the accumulated hours of operation for both the upper and lower dryer dryers independently. In many cases, it will match the motor hours of the machine. However, separate fields are provided in the event that a motor is replaced on a machine. See the Motor Hours description for more information.
The figure below shows the sub menu options for Usage:
52
Part # 8533-088-001 7/21
Control Menu:
The Control menu allows for the user to observe important technical information for the control. No chang es can be made at this menu. See below for detailed information on each sub menu.
1. “Serial Number”: This is the control serial number.
2. “MAC Address”: The MAC Address is a unique identifier designated to the control by the manu facturer. It allows the control to be recognized by network routers.
3. “IP Address”: The IP Address is the identifier given to the control by a network system.
4. “M Firmware”: The M Firmware is the Main Firmware currently loaded onto the control.
5. “C Firmware”: The C Firmware is the Communications Firmware currently loaded onto the con trol.
The figure below shows the sub menu options for Control:
Part # 8533-088-001 7/21
53
54
Part # 8533-088-001 7/21
Part # 8533-088-001 7/21
55
Pressure Testing
The dryer and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of ½ psig (14” water colum). The dryer must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than ½ psig.
Prssure testing port incoming
Prssure testing port outgoing
Clothes Door Removal
Step 1: Open door and remove inner hinge plate cover by removing the two Phillips screws.
Step 2: The clothes door may be removed from the hinge bracket by unscrewing and removing the top 3/16 allen head pivot screw located at the door upper hinge point, you will also need to use a ¼ allen wrench in the lower fastner.
Step 3: Next lean the door out of the top of the hinge bracket and lift the door from the bottom hinge pin.
3/16 Allen
1/4 Allen
Front Panel Removal
Step 1: Remove the loading door from the panel (optional, the front panel may be removed without taking off the door).
Step 2: Open upper service door, and remove lint door.
Step 3: Then remove the two left side phillips screws w/beveled washers and the two right side phillips w/beveled washers screws. Next disconnect door switch wires from back of loading door switch.
56
Part # 8533-088-001 7/21
Door Switch Removal & Installation
Step 1: Remove front panel (see front panel removal).
Step 2: Next disconnect door switch wires from back of loading door switch. Remove door switch by depressing the two tabs on switch and remove from the front of the panel.
Note: For the 80lb, you will have to remove the door switch cover first by removing the two 3/8” nuts.
Step 3: reassemble in reverse order.
Release
Release
Door Switch Operation & Testing
The normally open door switch must be closed (0 ohms resistance) for the motor and heat circuits to operate. When the door is opened, the door switch opens the 24 volt control circuit.
Part # 8533-088-001 7/21
57
Clothes Door Latch Adjustment
Step 1: Loosen the lock nut on the latching stud. It is located directly behind the door handle.
Step 2: Open the loading door.
Step 3: Screw the door catch stud in or out as necessary and then retighten the lock nut.
Installation of Clothes Door Window & Gasket
Step 1:
Step 2:
Remove the loading door.
Place the clothes door, with its face down, on a solid surface.
Note: Pre-warming the gasket under a heat lamp makes the installation much easier.
Step 3: Put the door glass gasket on the loading door with the ridges in the wide side up.
Locate the seam at the door latching stud.
Note: The gasket has one narrow opening on one side and a wide opening on the other.
The narrow side mounts to the door. The wide side holds the glass. The wide side has ridges on one interior lip. This ridged side should go up with the door lying face down.
Step 4: Coat the inside and outside of the gasket with rubber lubricant or liquid soap.
Step 5: Slide the glass into the middle of the gasket with half of the glass above the door
and half below the door.
Step 6: While pressing on the glass, use a modified screwdriver (grind the end off so that it is round and put a slight bend in it) and run it around half of the glass.
Step 7: With half of the glass installed, turn the door over and repeat step 6.
Step 8: Insert the modified screwdriver at the 6 o’clock position and pry the glass up enough to install the door glass support spacer (small diameter rubber tube).
58
Part # 8533-088-001 7/21
Glass inserted half way
High Limit Thermostat Locations & Functions Burner Housing
This hi-limit is located on the rear of the burner housing.
STEP 1: The thermostat opens the circuit to the main burners in the event of malfunction in the gas control area or temperature control. This thermostat will open quickly if there is
STEP 2: It is held in place by two screws. There are spacers a significant loss of air flow over the burner area.
between the thermostat and bracket which must be used to give proper operation.
Removal : To remove the hi-limit thermostat on the side of the burner housing, remove the terminal of each wires attached to the thermostat. Lastly, remove the mounting screws holding the thermostat to the burner housing.
High Limit Thermostat
Manual Resettable Over Temperature Safety Thermostat
The second hi-limit thermostat is located outside the rear exhaust opening mounted on the left side of the exhaust duct at the rear outlet height.
Step 1: The manually resettable thermostat limits the operating temperature a dryer can reach should some abnormal situation occur.
Step 2: Should the thermostat be tripped, the dryer will cease to heat until the thermostat is reset. Once the dryer cools, the thermostat may be reset by pushing the button in.
REMOVAL: To remove the manual resettable over temperature safety thermostat next to the exhaust duct. First, remove the terminals of each wire attached to the thermostat. Next, remove mounting screws holding the thermostat to the dryer cabinet.
Overtemp Thermostat
Part # 8533-088-001 7/21
59
Pressure Regulator Adjustment
Use the following procedure whenever it is necessary to check the pressure regulator setting. NOTE: Any adjustment of the pressure regulator must be made with a manometer attached at the plug in the main burner manifold.
Step 1:
Step 2:
Step 3:
Step 4:
Shut off the gas supply to the dryer.
Remove the 1/8” pipe plug from the end of the main burner manifold.
Attach a manometer to the manifold end.
Remove the pressure regulator cover screw on the gas valve.
Step 5: Open the shut-off valve, and operate the dryer.
Step 6: Adjust the pressure for a manometer reading of 3.5” water column gas pressure.
(11.0” for L.P.)
NOTE: The main burners must be operating when adjusting the pressure regulator.
Step 7: Shut off the gas supply to the dryer. Remove the manometer and install the 1/8” pipe plug in the manifold.
Step 8: Open the shut off valve, start the dryer and check for gas leaks while the burners are ignited.
NOTE: Always remove power from the machine before changing drive belts or working with the drive and fan system.
1/8” pipe plug
60
Adjustment Screw Under Plug
Final Drive Belt Replacement
To replace the final drive belt turn the cylinder slowly by hand and work the belt off of the large pulley.
Motor Drive Belt Replacement
To replace the motor drive belt the final drive belt should be removed as above. Next turn the intermediate drive pulley and work the belt off of it similarly to the above belt.
Blower Motor Removal
Step 1: Remove Rear upper and lower Belt pulley guards.
Step 2: Remove rear electrical box cover.
Step 3: Remove left and bottom side guard.
Step 4: Remove belts.
Step 5: Disconnect wires from the over temperature switch and cut the two wire ties securing gray wire to motor harness.
Step 6: Remove the wire clamp holding motor wire loom to cross member by removing the 5/16 screw.
Step 7: Remove the two beaded ties securing harness behind pulleys.
Step 8: Remove last wire tie connecting gray wire to motor harness.
Step 9: Next, inside the rear control box disconnect red wire, ¼ inch quick connect inside splice connector.
Step 10: Remove black and yellow wires from R1 relay.
Step 11: Remove motor harness from control box.
Step 12: Next remove blower motor, back plate, and impeller from machine by removing the four
9/16 nuts.
Reassemble in reverse order.
Part # 8533-088-001 7/21
Blower Impeller Removal
Remove Blower motor assembly. Take notice of the location of the impeller location on the shaft. Remove the two set screws that hold the motor to the shaft.
Airflow switch removal and adjustment
The air switch assembly is part of the ignition safety circuit and insures that the burner doesn’t operate unless ther is airflow. If this doesn’t happen, ignition will not occur. The air switch assembly is located on the back of the Dryer.
Adjustment Screw
Electronic Ignition Module
This machine uses an electronic spark ignition system to directly light the burners.
Step 1: The electronic ignition module (gray box) is located inside the rear control box.
Step 2: The red wire from the transformer provides 24 VAC through the 1.5 amp fuse and into the module to operate the entire direct ignition system.
Step 3: The black colored hi-voltage wire (spark plug type) plugs onto the post connector on the module, and the multi-wire plug fits into the side of the module.
Ignition Module
Spark Electrode Assembly-Removal
Step 1: Disconnect wires to electrodes.
Step 2: Remove two screws to detach electrode assembly.
NOTE: Proper grounding of the ignition system (yellow wires) is very critical for proper ignition sequence
If there is no spark or intermittent spark, check black hi-voltage lead wire for damage or cracks in insulation. This lead wire must not be taped or connected to any metal edges along its length to prevent pinching and arcing. Also, do not bundle this wire with other wires.
Note : Spark gap and electrode location are important. If the electrode is damaged or mounting is changed the spark gap may not be correct for ignition to occur. Check for cracks in the ceramic insulator. Replace electrode assembly if necessary. Also check for carbon or foreign material on the electrodes and clean if necessary.
Part # 8533-088-001 7/21
61
Gas Valve & Manifold Removal
Step 1: Disconnect union at gas valve and disconnect wires from gas valve operator coils.
Step 2: Remove Gas Valve mounting bracket by removing the 4 5/16 screws.
Upper Mounting Screws
Gas Valve Union
Main Burner Oriffice Removal
Step 1: Remove manifold and gas valve assembly as above.
Step 2: Using an open end wrench, remove orifices from manifold.
Brass Orffice
Main Burner Removal
Remove manifold & gas valve assembly as previously discussed. Remove thefour 9/16 screws securing the front of the burner to the support bracket. The burners may now be removed.
Cylinder Pulley Removal
30Lb
Remove bolt and washers holding pulley to cylinder shaft. Reincert bolt then using two or three jaw puller
Pull pulley straight off of shaft.
50lb & 80Lb
Remove bolt and washers holding pulley to cylinder shaft. Reincert bolt then using “T” puller w/ 3/8-
16UNC bolts, Pull pulley straight off of shaft
62
Part # 8533-088-001 7/21
Intermediate Pulley Removal
30Lb & 50Lb
The intermediate pulley can be removed by removing the snap ring holding the pulley to the tension arm.
Note: Cylinder pulley must be removed first.
80Lb
The intermediate pulley can be removed by removing the nut holding the pulley to the tension arm.
Snap Ring
Tension Arm Assembly Removal
The tension arm assembly may be removed by removing the snap ring that holds it to the tension arm support assembly pin. If it is necessary the arm assembly is replaced as a complete unit.
Snap Ring
Tension Arm Support Assembly Adjustment
The tension arm support assembly may be adjusted for alignment of the intermediate pulley and also to align the belts. The three outer nuts allow the alignment of the pin to be adjusted by pivoting the assembly on the center bolt. The center bolt can be screwed in to allow bringing the complete assembly farther back if necessary for belt alignment.
Upper Adj. Nut
Locking Bolt
Side Adjusting Nut
Side Adjusting Nut
Cylinder Removal
Step 1: Remove the front panel in front of the cylinder.
Step 2: Remove drive belt, bolt, washers, and pulley.
Step 3: Pull the cylinder from the front of the machine.
Part # 8533-088-001 7/21
63
Adjustment of Cylinder Assembly
Step 1: Loosen the two top adjusting bolts and two bottom adjusting nuts and lock nuts holding the bearing housing to the drive plate.
Step 2: Loosen the four mounting bolts on the side channels.
Step 3: Open the clothes door and insert a ½” thick shim at the 3 and 9 o’clock positions and a 1/4” thick shim at the 6 o’clock position.
Step 4: Tighten the two bottom adjusting nuts and tighten locking nuts.
Step 5: Tighten the bottom right mounting bolt, then the top left mounting bolt. Tighten the remaining two bolts. (Shim where and if necessary.)
Step 6: Tighten the two top adjusting bolts.
Step 7: Remove all the shims from between the front panel flange and cylinder (3,6,9 and 12 o’clock).
Step 8: Spin the cylinder to check for rubbing baffles, pressing down hard while rotating.
If rubbing is detected, repeat procedure paying particular attention to placement of shims between bearing housing and side channels.
Adjusting Bolts
Locking Bolts
Locking Bolts
Adjusting Nuts
Bearing Housing Removal
After removing cylinder as previously outlined, simply unbolt the four outside bolts and the two lower nuts and remove the bearing housing.
64
Part # 8533-088-001 7/21
Spark Electrode Assembly-Function
Step 1: The spark electrode and sensing electrodes are located directly at the side of the burner housing.
Step 2: The electrode with the black hi-voltage wire conducts the spark to the center grounding probe, directly over the burner.
Step 3: The electrode with the black sensing wire detects ignition and monitors flame by signaling the module.
NOTE: Proper grounding of the ignition system (yellow wires) is very critical for proper ignition sequence.
Ignition System-Function & Sequence
During normal dryer operation, the following occurs:
1.
The dryer electronic control calls for heat.
2.
From the 24VAC control transformer, voltage for the heat circuit is applied to the control through the door switch. If the control detects that the heat should be on, a circuit is closed providing power through the over-temp thermostat, the air damper switch, the high limit switch and the motor centrifugal switch to the Ignition Module.
Once the 24VAC reaches the ignition module on the red wire, sparking occurs at the ignition electrode and 24VAC is applied to open the Gas
Valve.
3.
Once the flame is established, the sensing electrode detects the presence of flame and the sparking stops.
4.
If for any reason the flame is not established in a period of 10 seconds, the electronic control will try this sequence for 3 tries. Normally the 10 seconds “Trial For Ignition” period is ample to establish and prove flame.
5.
If the flame is shutdown or blown out during operation, the ignitor will immediately go into “Trial. For Ignition” again for 10 seconds.
6.
However,at the end of 3 separate retries of 10 seconds “Trial for Ignition”, the flame is not established, the ignition system goes into “Safety Lock-Out” and will not reactivate the “Trial for Ignition” until there is a current interruption for a period of 15 seconds. This interruption can be provided by opening the dryer loading door and allowing the machine to come to a complete stop for 15 seconds.
Part # 8533-088-001 7/21
65
Tumbler does not turn
Drive belts
Check both drive belts. Replace if failed.
Tumbler does not turn Check capacitor and motor. Replace if failed
Door switch
Timer Tumbler does not turn
Check door switch contacts and adjustment.
Adjust or replace door switch.
Check to see if heat timer is turned on
Tumbler turns but no spark at burner Glass fuse
Thermostat
Ignition
Transformer
Over temperature
Ignition control
Air Flow Switch
Hi-limit
Gas supply
Check small glass control fuse in back of dryer. Replace if failed.
Check if voltage is passing through the two wires attached to the temoprature thermostat
Check for 24VAC output from transformer.
Replace if have 120V between black & white and no 24V between red and yellow.
Check to see if manually resettable thermostat. Thermostat is kicked out. Reset by pushing red reset button.
Check for 24VAC coming into the control on the at burner red wire. If voltage, then check for 24VAC out on the brown wire. Also check for spark at the ignitor. If no 24VAC output or no spark to the ignitor, replace ignition control.
Check air flow switch to be sure it closes when dryer is running. If not, adjust or replace switch.
Check for continuity. Should be 0 ohms resistance when cold. If not, replace thermostat.
No gas can cause system lockout
66
Part # 8533-088-001 7/21
Tumbler turns, ignition sparks, no flame
Gas supply
Gas pressure
Make sure gas supply is working.
Make manometer check of gas pressure. Adjust if necessary.
Spark Electrode Sensor
Gas valve
Ignition Control
Check for damage to electrode or mounting. Replace if necessary.
Check coil continuity, replace valve if failed.
Check for 24VAC to gas valve coils. If no voltage replace ignition control.
Burner Lights, but goes on and off
Slow drying
Electrodes
Temperature Setting
Check low voltage harness for possible wire break or cuts to allow no signal back to ignition control
Check thermostat for correct high temperature setting.
Adjust if necessary.
Manual overtemp
Tripping Frequently
Air flow restrictions necessary
Recirculating chamber Lint
Accumulation
Exhaust ducting Excessive lint buildup
Clean lint from top heat air chamber above tumbler
1. Check lint screen and clean if necessary.
2. Check exhaust for correct length and clean if necessary.
3. Check exhaust damper to insure that it opens when dryer is running and closes when dryer is not in use.
4. Check makeup air to insure that it is adequate. Increase makeup air if necessary.
5. Check static Back pressure no more than .3
Remove manual overtemp thermostat and inspect in chamber for excessive lint build up. Access also gained to this chamber by removing recirculation duct mounted at bottom of chamber, or the panel inside burner chamber between burners and rear back panel
Remove exhaust duct at rear of dryer and inspect for excessive lint build up in complete duct from dryer to where duct exits building.
Remove front panel completely. Be careful of any wiring attached. Remove heated air chamber cover and clean above tumbler back to burner housing.
Part # 8533-088-001 7/21
67
68
TEMP SENSOR
SHORT
TEMP SENSOR
OPEN
PCB ERROR1
Shorted Temperature
Sensor or wire.
Open Temperature
Sensor or wire
Memory corrupted
The dryer control shall not start until the detected short circuit is removed.
Regardless of condition of short circuit,
Error Code will be displayed until programming button is pressed to return machine to idle mode.
The dryer control shall not start until the detected short circuit is removed.
Regardless of condition of short circuit,
Error Code will be displayed until programming button is pressed to return machine to idle mode.
Power machine down and try to reset control. Varify voltage to the control board. Check ground to board. Replace control board if error can not be cleared
PCB ERROR2
COMM ERROR1
Analog/ Digital Error
Communication Bus
Error
Power machine down and try to reset control. Varify voltage to the control board. Check ground to board. Replace control board if error can not be cleared
Power machine down and try to reset control. Varify voltage to the control board. Check ground to board. Replace control board if error can not be cleared
COMM ERROR2 No Dryer Model Selected This error occurs when a pin combination on the model selection header is used that does not have a model designated for it. check connector marked Jumpers on the control board.
COMM ERROR7 Communication Bus
Error
If connected to DexterLive, Disconnect cable, and preform a soft restart by holding down the program button on power up.
Preform Soft restart.
contact your Dexter factory representive.
Fuse Error Internal Control program
Error.
Internal IC issue. Replace control.
CRC ERROR Firmware Corrupted The error is fatal. The control must be replaced.
Part # 8533-088-001 7/21
Part # 8533-088-001 7/21
69
70
Part # 8533-088-001 7/21
Part # 8533-088-001 7/21
71
72
Part # 8533-088-001 7/21
DC0030__-10
DC0050__-10
DC0080__-10
Part # 8533-088-001 7/21
73
Key Description
1 Loading Door Compleate SS/
Brushed SS/Blk
1 Loading Door Compleate Wht/
Brushed SS/Blk
2 Door Assy, Loading (Ring only)
Brushed SS
3 Plate Assy, Hinge (SS)
3 Plate Assy, Hinge (Wht)
* Cover-Hinge Back, Black
* Screw-10Bx3/8, Black
* Screw Hinge to Door
* Nut, Hinge to Door
4 Glass, Door
5 Gasket, Door Glass (Black)
* Support Door Glass
6 Gasket, Door Outer Rim (Black)
7 Handle, Loading Door
* Screw, Handle
8 Stud Door Catch
9 Nut-Hex, #10-32
10 Nut, Acorn
* Catch, Loading Door
* Rivit
11 Strap, Hinge (Black)
* Plate Assy-Backup, Hinge
* Plate Assy-Backup, Hinge
* Reinforcement-Front panel
T-30
9960-306-001
9960-306-003
9960-255-008
12 Screw-Phillips, 10-32x1/2 Chrome 9545-012-003
* Screw-Phillips-Counter sink, 10-
32x1/2 Chrome
NA
13 Screw-Special, Hinge to Door 9545-052-001
* Nut-Allen, 1/4-20
14 Washer-Fiber/Plastic
15 Front Panel Assy (SS)
15 Front Panel Assy (Wht)
16 Screw-Phillips, 10Bx1 3/4
8640-439-001
8641-436-003
9454-869-001
9454-869-003
9545-008-014
17 Washer-Finish
* Nut-Spring
8641-585-001
8640-399-001
* Insulation-Front Panel, Top Half 9277-062-001
* Insulation-Front Panel, Bottom Half 9277-062-002
* Switch-Door Closed
* Wire-Assy, Blk
9539-492-001
8220-063-026
* Wire-Assy-Blu
20 Coin Box Blue
20 Coin Box Black
21 Label-Warning, Dryer (Blue)
21 Label-Warning, Dryer (Black)
* Label-Warning, French, Spanish
* Cabinet Touch Up Paint (White)
8220-063-009
9807-099-002
9807-099-004
8502-758-002
8502-758-001
8502-764-001
9472-001-013
9982-374-001
9982-374-003
9074-341-002
9545-008-010
9545-012-015
8640-413-002
9212-002-003
9206-413-001
9548-117-000
9206-420-003
9244-082-001
9545-018-017
9531-033-001
8640-413-001
8640-413-003
9086-015-002
8638-190-009
9966-015-002
9982-371-001
74
Part # 8533-088-001 7/21
T-50
9960-305-001
9960-305-003
9960-284-002
9982-368-001
9982-368-003
9074-340-002
9545-008-010
9545-012-015
8640-413-002
9212-002-004
9206-413-002
9548-117-000
9206-420-005
9244-082-001
9545-018-017
9531-033-002
8640-413-001
8640-413-003
9086-015-002
8638-190-009
9966-014-002
9982-356-001
9545-012-003
9545-012-028
9545-052-001
8640-439-001
8641-436-003
9454-865-001
9454-865-003
9545-008-014
8641-585-001
8640-399-001
9277-057-001
9277-057-001
9539-492-001
8220-063-026
8220-063-009
9807-099-002
9807-099-004
8502-758-002
8502-758-001
8502-764-001
9472-001-013
T-80
9960-305-001
9960-305-003
9960-284-002
9982-368-001
9982-368-003
9074-340-002
9545-008-010
9545-012-015
8640-413-002
9212-002-004
9206-413-002
9548-117-000
9206-420-005
9244-082-001
9545-018-017
9531-033-002
8640-413-001
8640-413-003
9086-015-002
8638-190-009
9966-014-002
9982-369-001
9817-003-001
9545-012-003
9545-012-028
9545-052-001
8640-439-001
8641-436-003
9454-867-001
9454-867-003
9545-008-014
8641-585-001
8640-399-001
9277-058-001
9278-058-002
9539-492-001
8220-063-026
8220-063-009
9807-099-002
9807-099-004
8502-758-002
8502-758-001
8502-764-001
9472-001-013
QTY
1
1
1
1
1
2
1
2
4
1
1
4
1
2
4
1
2
1
1
1
1
1
1
1
4
4
1
1
1
1
1
1
1
1
4
4
1
1
1
1
1
1
1
1
4
21
1
8, 9, 10
7
20
2 4
3 13
16, 17 15 6 5 11, 14
Part # 8533-088-001 7/21
75
Key Description
1 Nameplate - Dexter Dryer Blue
T-30
9412-216-002
1
2
Nameplate - Dexter Dryer Black
Door Assy-Upper, Coin (SS)
9412-216-001
9960-311-001
*
7
5
6
*
*
*
2
3
4
9
9
8
8
Door Assy-Upper, Coin (Wht)
Bracket-Hinge
Rivit- 3/16, Hinge to Door
Rivit- 3/16, Hinge to Cabinet
9960-311-003
9029-224-001
9491-009-001
9491-009-001
Trim-Upper Service Door, Black 9578-098-002
Screw-Phillips, 10Bx3/8, Black
Lock Assy and Key Upper
Lock Spacer
Cam Lock Upper Door
Key, 6324
9545-008-010
8650-012-003
9538-189-001
9095-047-001
6292-006-007
Overlay-Control, Coin, Blue
Overlay-Control, Coin, Black
Button-Push, Control, Blue
Button-Push, Control, Black
9435-042-002
9435-042-001
9035-062-001
9035-062-002
*
*
*
Spacer-Push Button (Micro)
Retainer-Push Button (Micro)
Nut, Hex-Elastistop, #4-40
*
*
10 PCB-Controler
* Spacer-#6 x 9/16
Spacer #6 x 7/8
Nut- #6-32
Nut- #6-32 (Grounding nut)
11 Wire Assy-GRN, 24”
9538-192-001
9486-150-001
8640-424-002
9471-022-001
9538-157-018
9538-157-017
8640-411-003
8640-411-001
8220-137-001
* Harness, Main
12 Support-Upper Service Door
13 Clamp-Tube
14 Nut, #6-32
15 Clamp-Cable, 1/2”
* Nut, #6-32
9627-912-001
9548-288-001
9079-121-002
8640-411-003
8654-125-006
8640-411-003
16 Insulation
17 Coin Acceptor
9277-041-016
9021-042-001
*
*
18 Retainer-Coin Accecptor
19 Screws-Torq, 4Bx5/8 ss
*
9486-149-001
9545-053-002
Switch Assembly, Optical, Single 9150-099-002
Coin Shute
Screw
9940-017-001
9545-008-001
*
*
Thumb Drive
Nut, Elastic Stop
9150-045-002
8640-413-004
T-50
9412-216-002
9412-216-001
9960-312-001
9538-192-001
9486-150-001
8640-424-002
9471-022-001
9538-157-018
9538-157-017
8640-411-003
8640-411-001
8220-137-001
9627-912-002
9548-288-002
9079-121-002
8640-411-003
8654-125-006
8640-411-003
9277-041-016
9021-042-001
9486-149-001
9545-053-002
9150-099-002
9940-017-001
9545-008-001
9960-312-003
9029-224-001
9491-009-001
9491-009-001
9578-094-002
9545-008-010
8650-012-003
9538-189-001
9095-047-001
6292-006-007
9435-046-002
9435-046-001
9035-062-001
9035-062-002
9150-045-002
8640-413-004
T80
9412-216-002
9412-216-001
9960-313-001
9538-192-001
9486-150-001
8640-424-002
9471-022-001
9538-157-018
9538-157-017
8640-411-003
8640-411-001
8220-137-001
9627-912-003
9548-288-002
9079-121-002
8640-411-003
8654-125-006
8640-411-003
9277-041-016
9021-042-001
9486-149-001
9545-053-002
9150-099-002
9940-017-001
9545-008-001
9960-313-003
9029-224-001
9491-009-001
9491-009-001
9578-096-002
9545-008-010
8650-012-003
9538-189-001
9095-047-001
6292-006-007
9435-047-002
9435-047-001
9035-062-001
9035-062-002
9150-045-002
8640-413-004
1
1
2
4
1
1
1
2
2
1
1
1
1
2
2
4
1
3
1
1
1
*
1
1
QTY
1
*
1
4
1
1
1
2
2
AR
1
1
1
1
1
2
76
Part # 8533-088-001 7/21
19
17
5 4 9 8
3
6 2
16
1
2 10
15 18
13, 14 7 12
11
Part # 8533-088-001 7/21
77
Key Description
1 Door-Lower Service, Coin, SS
1 Door-Lower Service, Coin, Wht
2 Lock Assy and Key Lower Door
* Lock Spacer
* Cam Lock Lower Door
* Washer-Flat
3 Handle-Door, Lower Service
4 Screw-Phollips, 10Bx3/8, Black
5 Trim-Lower Kick, Black
6 Screw-Phollips, 10Bx3/8, Black
7 Screen Assy, Lint
8 Switch-Door Closure
9 Hinge-Door, Lower
10 Screw-5/16, 10ABx3/8
11 Bracket-Door Switch
* Rivit, 1/8 Low Profile
12 Bracket-Chain
* Rivit, 1/8 Low Profile
13 Hook, “S” Type
14 Chain
* Leg, Leveling 1/2”
* Leveling Leg Wrench
T-30
9108-130-001
9108-130-003
8650-012-004
9538-189-001
9095-048-001
8641-581-041
9244-084-002
9545-008-010
9578-099-002
9545-008-010
9822-026-002
9539-492-001
9243-081-001
9545-008-024
9029-226-001
9491-009-004
9029-223-001
9491-009-004
9248-022-002
9099-012-006
8544-006-001
8545-061-002
T-50
9108-122-001
9108-122-003
8650-012-004
9538-189-001
9095-048-001
8641-581-041
9244-087-002
9545-008-010
9578-095-002
9545-008-010
9822-026-001
9539-492-001
9243-082-001
9545-008-024
9029-226-001
9491-009-004
9029-223-001
9491-009-004
9248-022-002
9099-012-006
8544-006-001
8545-061-002
T80
9108-126-001
9108-126-003
8650-012-004
9538-189-001
9095-048-001
8641-581-041
9244-088-002
9545-008-010
9578-097-002
9545-008-010
9822-031-002
9539-492-001
9243-082-001
9545-008-024
9029-226-001
9491-009-004
9029-223-001
9491-009-004
9248-022-002
9099-012-006
8544-006-001
8545-061-002
2
4
8
4
1
1
2
1
5
2
1
4
1
5
1
1
QTY
1
*
1
1
1
2
78
Part # 8533-088-001 7/21
3 4 2
1
9
8
10
7
5
6
11 12
13, 14
4
2
Part # 8533-088-001 7/21
79
Key Description
T-30 T-50 T80
1 Insulation, Upper service Door
2 Insulation, RH Burnner
3 Insulation Tumbler Area, above
Baffel
3 Insulation Tumbler Area, above
Baffel
4 Insulation Tumbler Area, below baffel
4 Insulation Tumbler Area, below baffel
5 Insulation Lint Compartment
* Screen Assy, Lint
6 Switch-Door Closure
7 Hinge-Door, Lower
8 Screw-5/16, 10ABx3/8
9 Lint Hood-Back
10 Nut Wizlock, 8-32
11 Lint hood, LH
12 Lint hood, RH
13 Lint hood, Top
14 Screw, 5/16- 10ABx3/8
15 Impeller, w/set screws
16 Harness -Temp Probe
17 Wire Nut, #71B
18 Bracket, Temp Probe
19 Screw-5/16, 10ABx3/8
20 Temp Probe
21 Screw-Phillips, 8Bx1/4
22 Vault, Coin
* Plate Assy/Coin vault mounting
* Nut/ Hexelastic stop
9277-041-006
9277-041-019
9277-041-020
9277-041-020
9277-041-021
9822-026-002
9539-492-001
9243-081-001
9545-008-024
9240-038-001
8640-412-004
9240-040-001
9240-040-002
9240-039-001
9545-008-024
9278-043-001
9627-679-002
8640-276-005
9029-197-001
9545-008-024
9501-004-002
9545-045-005
9942-039-002
9982-338-001
8640-413-004
23 Coin Shute
* Screw, 10Bx1/4
24 Harness, Main
9940-017-001
9545-008-001
9627-912-001
9277-041-016
9277-041-019
9277-051-003
9277-051-003
9277-051-003
9277-051-003
9241-041-024
9822-026-001
9539-492-001
9243-082-001
9545-008-024
9240-041-001
8640-412-004
9240-043-001
9240-043-002
9240-042-001
9545-008-024
9278-038-004
9627-679-002
8640-276-005
NA
NA
9501-004-002
9545-045-005
9942-039-002
9982-338-001
8640-413-004
9277-041-016
9277-041-023
9277-041-021
9277-041-021
9277-051-004
9277-051-004
9277-041-025
9822-031-002
9539-492-001
9243-082-001
9545-008-024
9240-044-001
8640-412-004
9240-046-001
9240-046-002
9240-045-001
9545-008-024
9278-037-003
9627-679-002
8640-276-005
NA
NA
9501-004-002
9545-045-005
9942-039-002
9982-338-001
8640-413-004
2
2
2
9940-017-001
9545-008-001
9627-912-002
9940-017-001
9545-008-001
9627-912-003
1
1
1
1
2
14
1
1
1
1
1
6
1
1
1
1
1
1
2
1
1
2
1
AR
QTY
1
1
2
80
19
Part # 8533-088-001 7/21
16 17 18 21 20 21 20 17 16
24
23
22
1
2
3
11
5
6
15
4
16
14
4
13
5
12
7
10
8 9
Part # 8533-088-001 7/21
81
82
8, 9
7
10
11
17
16
15
Part # 8533-088-001 7/21
Key Description T-30
1 Motor
2 Pulley
* Set screw
3 Plate, Motor mounting
* Gasket, Motor Plate
4 Nut-3/8-16, Plate to cabinet
* Impeller w/set screw
5 Screw, 5/16-18x5/8
6 Nut, 3/8-16
7 Support Arm, Intermediate pulley
8 Bolt- 3/8-16x1 1/4
9376-311-003
9453-157-001
9545-028-013
9982-370-002
9206-428-001
8640-415-004
9278-043-001
9545-014-004
8640-415-004
9991-053-001
9545-029-010
9 Nut, Wizlock, 3/8x16
* Cap Screw, 3/8-16x1 1/2
* Snap Ring
* Washer-Flat, 3/8x1
10 Idler Arm Assembly
11 Washer-Flat, 3/8x1
12 Pulley, Idler w/Bearings
13 Bearing, Bronze
14 Snap Ring
15 Hook “S” type
16 Chain, Spring tension
17 Spring, tension
18 Chain, Limit
19 Belt Drive
* Tolerence Ring
20 Pulley, Driven
21 Washer-Flat, 1/2
22 Washer-Lock, Ext. tooth, 1/2
23 Bolt-3/4, 1/2-13x1/14
24 Belt, Driven
8640-415-004
9545-029-003
9487-200-003
8641-581-020
9861-022-001
8641-581-020
9908-039-004
9036-145-002
9487-200-003
9248-022-002
9099-012-002
9534-319-002
9099-012-007
9040-076-003
9487-234-005
9908-049-002
8641-581-021
8641-582-016
9545-017-019
9040-073-009
3
1
1
1
1
1
1
1
1
2
1
3
2
1
1
1
3
1
1
1
1
QTY
1
1
1
1
1
4
4
4
1
1
18
15
15
24
12
13, 14
19
1
20
21, 22, 23
15
18
4
3
2
5, 6
Part # 8533-088-001 7/21
83
16
8, 9
15
14
84
Part # 8533-088-001 7/21
Key Description
1 Motor
* Run Capacitor, Motor
* Start Capacitor, Motor
2 Pulley
* Set screw
3 Plate, Motor mounting
* Gasket, Motor Plate
4 Nut-3/8-16, Plate to cabinet
* Impeller w/set screw
5 Screw, 5/16-18x5/8
6 Nut, 3/8-16
7 Support Arm, Intermediate pulley
8 Bolt- 3/8-16x1 1/4 9545-029-010
9 Nut, Wizlock, 3/8x16
* Cap Screw, 3/8-16x1 1/2
* Snap Ring
* Washer-Flat, 3/8x1
10 Idler Arm Assembly
8640-415-004
9545-029-012
9487-200-003
8641-581-035
9861-022-002
* Snap Ring (Support Arm keeper) 9487-200-003
* Snap Ring
* Washer-Flat, 3/8x1
11 Pulley, Idler w/Bearings
12 Bearing, Bronze
13 Snap Ring
14 Hook “S” type
9487-200-003
8641-581-035
9908-048-003
9036-145-002
9487-200-003
9248-022-002
15 Chain, Spring tension
16 Spring, tension
17 Belt Drive
* Tolerence Ring
18 Pulley, Driven
19 Washer-Flat, 1/2
20 Washer-Lock, Ext. tooth, 1/2
21 Bolt-3/4, 1/2-13x1/14
22 Belt, Driven
23 Thermostat-Overtemp, Reset
9099-012-002
9534-151-000
9040-076-006
9487-234-005
9908-047-002
8641-581-026
8641-582-016
9545-017-009
9040-073-011
9576-207-006
T-50
9376-317-003
5191-108-001
5191-109-001
9453-169-013
9545-028-013
9982-370-002
9206-428-001
8640-415-004
9278-038-004
9545-014-004
8640-415-004
9991-053-002
3
1
1
2
1
1
1
3
1
1
1
1
1
1
1
1
1
1
1
1
3
1
1
1
1
1
1
1
1
4
4
4
1
1
QTY
1
10
7
22
11
12, 13
17
5, 6
1
4
18
19, 20, 21
23
3
2
Part # 8533-088-001 7/21
85
86
20
11
19
18
Part # 8533-088-001 7/21
Key Description
1 Motor
* Run Capacitor, Motor
* Start Capacitor, Motor
2 Pulley
* Set screw
3 Plate, Motor mounting
* Gasket, Motor Plate
4 Nut-3/8-16, Plate to cabinet
* Impeller w/set screw
5 Screw, 5/16-18x5/8
6 Nut, 3/8-16
* Tollerence Ring
7 Pulley, Driven
8 Washer-Flat, 1/2
9 Washer-Lock, Ext. tooth, 1/2
10 Bolt-3/4, 1/2-13x1/14
11 Support Arm, Intermediate pulley
12 Bolt- 3/8-16x1 1/4
13 Nut, Wizlock, 3/8x16
* Cap Screw, 3/8-16x1 1/2
* Snap Ring
* Washer-Flat, 3/8x1
14 Idler Arm Assembly
* Snap Ring
* Washer-Flat, 3/8x1
15 Pulley, Idler w/Bearings
* Snapring, Inside-Bearing
* Bearing, Ball
* Spacer, Bearing
16 Washer-Flat
17 Nut, 5/8-11
18 Hook “S” type
19 Chain, Spring tension
20 Spring, tension
21 Belt Drive
22 Belt, Driven
23 Thermostat-Overtemp, Reset
9545-029-010
8640-415-004
9545-029-002
9487-200-003
8641-581-020
9861-024-004
9487-200-006
8641-581-039
9908-042-006
9487-238-005
9036-159-007
9538-173-002
8641-581-039
8640-425-002
9248-022-002
9099-012-002
9534-151-000
9040-076-011
9040-073-012
9576-207-006
T-80
9376-317-003
5191-108-001
5191-109-001
9453-157-001
9545-028-013
9982-372-002
9206-428-001
8640-415-004
9278-037-003
9545-014-004
8640-400-003
9487-234-001
9908-043-002
8641-581-026
8641-582-016
9545-017-009
9991-053-002
3
3
1
1
1
1
1
1
4
1
4
1
1
1
4
1
1
1
1
1
1
1
QTY
1
1
1
1
1
1
1
1
3
1
2
1
1
1
14
12, 13
22
15
16, 17
21
1
5, 6
4
8, 9, 10
7
23
3
2
Part # 8533-088-001 7/21
87
Key Description
T-30 T-50 T80
1 Cover Cabinet
* Screw-5/16, 10ABx3/8
2 Cover-Control Box
3 Screw-5/16, 10ABx3/8
4 Guard, RH
9074-347-001
9545-008-024
9074-346-001
9545-008-024
9208-093-001
9074-348-001
9545-008-024
9074-346-001
9545-008-024
9208-097-001
9074-349-001
9545-008-024
9074-346-001
9545-008-024
9208-101-001
* Screw-5/16, 10ABx3/8
5 Guard Base & LH
* Screw-5/16, 10ABx3/8
6 Guard-Lower
7 Screw-5/16, 10ABx3/8
8 Guard-upper
* Screw-5/16, 10ABx3/8
9 Elbow-90 degree, 8”
10 Pipe-Duct, 8”
11 Tee-Duct, Recirculation, 8”-6”
12 Damper
* Pin-Damper, Hinge
* Nut-Spring
13 Bracket-Recirculation Duct,
Small
14 Pipe-Duct, 6”
15 Bracket-Duct, Recirculation
Large
16 Elbow-90 degree, 6”
* Operators Manual
17 Diagram & Schematics
18 Label-Warning & Notice
19 Label-Instructions
20 Decal-Lighting & Clearence
21 Label-High Voltage
* 8” Slide Open Clean Out Duct
9545-008-024
9208-094-001
9545-008-024
9208-095-001
9545-008-024
9208-096-001
9545-008-024
9042-039-001
9109-121-001
9810-018-001
9125-002-001
9451-146-002
8520-141-000
9029-228-001
9109-122-001
9029-246-001
9142-039-002
8514-234-001
9506-546-001
8502-763-001
8502-645-001
8527-151-001
8502-614-004
9973-034-001
9545-008-024
9208-098-001
9545-008-024
9208-099-002
9545-008-024
9208-100-001
9545-008-024
9042-039-001
9109-121-001
9810-018-001
9125-002-001
9451-146-002
8520-141-000
9029-228-001
9109-122-002
9029-247-001
9142-039-002
8514-234-001
9506-546-001
8502-763-001
8502-645-001
8527-151-001
8502-614-004
9973-034-001
9545-008-024
9208-102-001
9545-008-024
9208-103-001
9545-008-024
9208-104-001
9545-008-024
9042-039-001
9109-121-002
9810-019-001
9125-008-001
9451-146-002
8520-141-000
9028-228-001
9109-122-003
9029-247-001
9142-039-002
8514-234-001
9506-546-001
8502-6763-001
8502-645-001
8527-151-001
8502-614-004
9973-034-001
1
1
1
1
1
1
1
1
1
1
1
AR
1
AR
1
AR
1
AR
QTY
1
AR
1
AR
1
1
2
1
1
1
1
16
2
14
12
11
13
88
Part # 8533-088-001 7/21
1
4
17
3
2
21
20
7
8
6
16
15
11
18
19
10
5
9
Part # 8533-088-001 7/21
89
1
2
6 5
3
Key Description
* Bearing Housing Complete Assy (Includes bearings &
Spacer)
1 Housing, Bearing
* Bearing, Ball, Front
* Spacer, Bearing
2 Bearing, Ball, Rear
3 Screw-Wizlock, 3/8-24x3/4
4 Nut, 5/16-18
5 Screw, 3/8-24x1
6 Nut, 3/8-24
* Shim, Tumbler
T-30
9803-160-003
9241-161-002
9036-130-001
9538-139-002
9036-130-001
9545-049-002
8640-400-002
9545-049-001
8640-415-002
9538-139-002
4
QTY
1
4
2
1
4
2
AR
1
1
1
90
Part # 8533-088-001 7/21
5
10 12
11
2 3 1 4 5 6
Key Description
* Tumbler Assy Compleate W/Spider (GALV)
1 Tumbler Assy (Galvinized)
1 Tumbler Assy Compleate W/Spider (SS & Galv front)
1 Tumbler Assy (Stainless Galvinized front)
2 Rod, Tumbler
3 Washer, Special
4 Shim
5 Spider Assy
6 Nut, Wiz Lock
7 Spacer-Shaft
8 Tolerence Ring
9 Pulley, Driven
10 Washer -Flat
11 LockWasher - IntTooth, 1”
12 Screw, 1/2-13x1 1/4
T-30
9848-147-001
9848-146-001
9848-147-002
9848-146-002
9497-019-003
8641-554-001
9552-013-003
9568-015-001
8640-415-004
9538-164-001
9487-234-005
9908-049-002
8641-581-026
8641-582-016
9545-017-009
7 8 9
1
1
1
1
1
1
1
3
1
3
3
AR
QTY
1
1
1
Part # 8533-088-001 7/21
91
1 6
2
5
3
Key Description
Bearing Housing Complete Assy (Includes bearings & Spacer)
1 Housing, Bearing
* Bearing, Ball, Front
* Spacer, Bearing
2 Bearing, Ball, Rear
3 Screw-Wizlock, 1/2-13x3/4
4 Nut, 1/2-13
5 Screw, 1/2-13x1 1/2
6 Nut, 1/2-13
T-50
9803-201-001
9241-189-002
9036-159-001
9538-183-001
9036-159-003
9545-017-017
8640-417-002
9545-017-018
8640-417-002
4
2
2
2
1
1
1
1
4
QTY
1
92
Part # 8533-088-001 7/21
5
10 12
11
2 3 1 4 5 6
Key Description
* Tumbler Assy Compleate W/Spider (GALV)
1 Tumbler Assy (Galvinized)
* Tumbler Assy Compleate W/Spider (SS & Galv front)
1 Tumbler Assy (Stainless Galvinized front)
2 Rod, Tumbler
3 Washer, Special
4 Shim
5 Spider Assy
6 Nut, Wiz Lock
7 Spacer-Shaft
8 Tolerence Ring
9 Pulley, Driven
10 Washer -Flat
11 LockWasher - IntTooth, 1”
12 Screw, 1/2-13x1 1/4
T-50
9848-149-001
9848-148-001
9848-149-002
9848-148-002
9497-226-002
8641-590-002
9552-013-000
9568-013-001
8640-417-005
9538-184-001
9487-234-005
9908-047-002
8641-581-026
8641-582-016
9545-017-009
7 8 9
1
1
3
1
AR
1
1
1
1
1
3
1
1
3
QTY
1
Part # 8533-088-001 7/21
93
1
2
9
8
5
4
3
Key Description
Bearing Housing Complete Assy (Includes bearings &
Spacer)
1 Housing, Bearing
* Bearing, Ball, Front
* Spacer, Bearing
2 Bearing, Ball, Rear
3 Washer, Flat 1/2
4 Lock Washer Spring, 1/2
5 Screw, 1/2-13x1
6 Lock Washer Spring, 1/2
7 Nut, 7/16-14
8 Screw, 7/16-14x1 1/2
9 Nut, 7/16-14
T80
9803-189-001
9241-183-003
9036-159-001
9036-159-002
8641-581-026
8641-582-004
9545-017-004
8641-582-004
8640-416-001
9545-059-003
8641-416-001
6 7
QTY
94
Part # 8533-088-001 7/21
12
9 11
10
2 3
1
4
5 6
7
8
Key Description
* Tumbler Assy Compleate W/Spider (GALV)
1 Tumbler Assy (Galvinized)
1 Tumbler Assy Compleate W/Spider (SS & Galv front)
1 Tumbler Assy (Stainless Galvinized front)
2 Rod, Tumbler
3 Washer, Special
4 Shim
5 Spider Assy w/Front Bearing
6 Nut, Wiz Lock
7 Tolerence Ring
8 Pulley, Driven
9 Washer -Flat
10 LockWasher - IntTooth, 1”
11 Screw, 1/2-13x1 1/4
12 Bearing, Front
T80
9848-151-001
9849-150-001
9848-151-002
9849-150-002
9497-266-001
8641-590-001
9552-013-000
9873-008-001
8640-417-005
9487-234-001
9908-043-002
8641-581-026
8641-582-016
9545-017-009
9036-159-002
4
4
1
1
AR
1
QTY
1
1
1
1
4
1
1
1
1
Part # 8533-088-001 7/21
95
Key Description
9
10
11
12
13
14
15
16
17
18
19
20
21
*
*
22
23
5
6
3
4
7
8
*
1
2
Housing Assembly, Burner
Panel-Burner Housing, Side Left
Baffle-Burner Housing, Center
Panel-Burner Housing, Top
Panel-Burner Housing, Front
Panel-Burner Housing, Back
Baffle-Burner Housing, Recirculation
Baffle-Burner Housing, Front
Duct Adaptor, 6”x3” long
Burner, Main
Bracket-Support, Electrode
Bracket-Support, Gas Valve
Electrode-Ignition
Control Assy,Gas Valve, White Rodgers 36J
Manifold Assy
Valve-Gas Shutoff, (Optional)
Thermostat-HI-Limit
Screw, 10ABx3/8
Screw, 10ABx1/4
Orfice-Natural, .125
Orfice-LP, #48
Kit, LP Conversion, White Rodgers
Bracket-Support, Burner
Panel-Burner Housing, Side Right
Screw, 10-32TTx1/2 Green
Screw, 8-32x3/8
Part Number
9803-210-001
9454-845-001
9049-091-001
9454-871-001
9454-847-001
9454-848-001
9049-092-001
9049-093-001
9109-120-01
9048-021-001
9029-214-001
9029-227-001
9875-002-003
9857-192-001
9381-009-007
9379-196-001
9576-203-002
9545-008-024
9545-008-006
9425-069-023
9425-069-003
9732-102-018
9029-225-001
9454-861-001
9545-008-027
9545-010-014
Qty
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
3
4
24
17
2
96
Part # 8533-088-001 7/21
17 16 5 22 9 3
17
17
17
18
8
18
12
10
21
17 20 14 13
17
11
15
23
18
1
18
19
6
2
7
17
4
Part # 8533-088-001 7/21
97
11
12
13
14
15
16
17
18
19
20
21
7
8
5
6
9
10
3
4
1
2
*
23
*
*
24
25
26
27
Key Description
Housing Assembly, Burner
Panel-Burner Housing, Front
Panel-Burner Housing, Side Right
Panel-Burner Housing, Side Left
Panel-Burner Housing, Back
Baffle-Burner Housing, Center
Panel-Burner Housing, Top
Panel-Burner Housing, Top
Baffle-Burner Housing, Extention
Duct Adaptor, 6”x1.25” long
Baffle-Burner Housing, Recirculation
Side-Extention Baffle, Burner Housing
Bracket-Support, Burner
Burner, Main
Screw, 10T-32x1/2
Electrode-Ignition
Cover-Burner, Intet
Bracket-Support, Gas Valve
Control Assy,Gas Valve, White Rodgers 36J
Screw, #8-32x3/8
Valve-Gas Shutoff, (Optional)
Manifold Assy
Orfice-Natural, #30
Orfice-LP, #48
Kit, LP Conversion, White Rodgers
Thermostat-HI-Limit
Spacer-1/4x5/8 long
Screw-8Bx1
Screw, 10Bx1/4
Screw, 10ABx3/8
Part Number
9803-211-001
9454-863-001
9454-861-001
9454-862-001
9454-864-001
9049-098-001
9454-849-001
9074-343-001
9049-100-001
9109-120-003
9049-099-001
9551-049-001
9029-213-001
9048-021-001
9545-008-008
9875-002-003
9074-344-001
9029-227-001
9857-192-001
9545-010-014
9379-196-001
9381-010-003
9425-069-002
9425-069-003
9732-102-017
9576-203-002
9538-166-009
9545-045-013
9545-008-001
9545-008-024
Qty
3
3
1
4
1
1
1
1
3
3
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
22
31
2
2
98
Part # 8533-088-001 7/21
26
2
26
16
21
17 19
4
11
25
23
24
25
23
24
21
18
20 15
6
26
26
12
14
13
1
10
5
13
3
8
9
7
26 5 27 10
27
27
27
Part # 8533-088-001 7/21
99
16
17
18
19
20
21
10
11
12
13
14
15
7
8
5
6
9
3
4
1
2
25
26
27
28
22
*
*
23
24
Key Description
Housing Assembly, Burner
Panel-Burner Housing, Front
Panel-Burner Housing, Side Right
Panel-Burner Housing, Side Left
Panel-Burner Housing, Back
Baffle-Burner Housing, Center
Panel-Burner Housing, Top
Panel-Burner Housing, Top
Baffle-Burner Housing, Extention
Duct Adaptor, 6”x1.25” long
Baffle-Burner Housing, Recirculation
Side-Extention Baffle, Burner Housing
Bracket-Support, Burner
Burner, Main
Screw, 10T-32x1/2
Electrode-Ignition
Cover-Burner, Intet
Bracket-Support, Gas Valve
Control Assy,Gas Valve, White Rodgers 36J
Bracket-support, Gas Valve Left hand
Valve-Gas Shutoff, (Optional)
Manifold Assy
Orfice-Natural, #29
Orfice-LP, #46
Kit, LP Conversion, White Rodgers
Thermostat-HI-Limit
Spacer-1/4x5/8 long
Screw-8Bx1
Screw, 10Bx1/4
Screw, 10ABx3/8
Bushing-Reducer, 3/4x1/2
Qty
1
4
1
1
1
1
1
4
1
2
4
1
1
1
1
1
1
1
1
1
1
1
2
22
31
1
1
1
3
3
2
Part Number
9803-212-001
9454-863-001
9454-861-001
9454-862-001
9454-864-001
9049-098-001
9454-849-001
9074-343-001
9049-100-001
9109-120-002
9049-099-001
9551-049-001
9029-213-001
9048-021-001
9545-008-008
9875-002-003
9074-344-001
9029-234-001
9857-193-001
9029-235-001
9379-196-001
9381-014-001
9425-069-021
9425-069-022
9732-102-023
9576-203-002
9538-166-009
9545-045-013
9545-008-001
9545-008-024
8615-104-009
100
Part # 8533-088-001 7/21
26
2
27
26 16
21
17
18
4
19
7
25
23
24
18
28
20
26
15
6
26
26
14
12
13
1
13 10
3
26
7 5
27
10
27 27
27
Part # 8533-088-001 7/21
101
4
8
2
3
5
7
6
1
Key Description
* Air Flow switch Assy
1 Bracket-Airflow switch
2 Shield-Switch
3 Switch-Micro
4 Nut-Twin, 4-40
5 Screw-.625, 4-40
6 Actuator-Air Flow Switch
7 Pin-Cotter, .09375x.75
Screw, 10Bx1/4
T-30
9801-095-001
9029-174-001
9550-169-003
9539-461-009
8640-401-001
9545-020-001
9008-007-001
9451-169-002
9545-008-001
T-50
9801-098-001
9029-200-001
9550-169-003
9539-461-009
8640-401-001
9545-020-001
9008-007-001
9451-169-002
9545-008-001
T80
9801-098-001
9029-200-001
9550-169-003
9539-461-009
8640-401-001
9545-020-001
9008-007-001
9451-169-002
9545-008-001
2
1
1
3
4
QTY
1
1
1
1
1
102
Part # 8533-088-001 7/21
9, 10
11 12 7 6 3 4
5
18 17 19
Key Description
1 Wrapper-Control Box
2 Screw, 5/16-10AB-3/8
* Cover-Control Box
T-30
9636-200-001
9545-008-001
9074-346-001
* Screw, 5/16-10AB-3/8
3 Strip-Marker, Terminal
9545-008-024
9558-029-005
4 Terminal Block Assy-Power, 4Pole 9897-035-001
5 Screw, 5/16-10AB-3/8 9545-008-024
6 Wire assy-Blk/Red, 6 1/2”
7 Wire assy-Blk/Blu, 6 1/2”
8220-001-230
8220-001-231
8 Wire Assy, GRN, 7”
9 Screw- 10-32TTx1/2 GRN
10 Lockwasher, External tooth
11 Transformer, w/Circuit braker
12 Screw, 5/16-10AB-3/8
8220-001-478
9545-008-027
8641-582-006
8711-007-002
9545-008-024
13 Relay-Motor, 30Amp, 24VAC
14 Screw, 5/16-10AB-3/8
15 Wire assy-Blk/Red, 9”
16 Wire assy-Blk/Blu, 9”
17 Control Assy, Ignition (Module)
18 Screw-8Bx3/4”
5192-299-002
9545-008-024
8220-146-001
8220-146-002
9857-182-001
9545-045-007
* Harness, Ignition Module
19 Wire Assy- High Voltage Lead
9627-867-003
9631-403-009
13 14
T-50
9636-200-001
9545-008-001
9074-346-001
9545-008-024
9558-029-005
9897-035-001
9545-008-024
8220-001-230
8220-001-231
8220-001-478
9545-008-027
8641-582-006
8711-007-002
9545-008-024
5192-299-002
9545-008-024
8220-146-001
8220-146-002
9857-182-001
9545-045-007
9627-867-003
9631-403-009
16 15 8 1
T80
9636-200-001
9545-008-001
9074-346-001
9545-008-024
9558-029-005
9897-035-001
9545-008-024
8220-001-230
8220-001-231
8220-001-478
9545-008-027
8641-582-006
8711-007-002
9545-008-024
5192-299-002
9545-008-024
8220-146-001
8220-146-002
9857-182-001
9545-045-007
9627-867-003
9631-403-009
2
1
1
1
2
1
1
1
1
6
1
QTY
1
1
1
1
1
2
1
1
1
2
1
2
Part # 8533-088-001 7/21
103
104
Part # 8533-088-001 7/21
Key
3
4
1
2
Description
Optical Coin Acceptor
Replacement Optical Sensor
Retainer-Coin Accecptor
Screws-Torq, 4Bx5/8 ss
T30
9021-041-001
9801-099-002
9486-149-001
9545-053-002
T50
9021-041-001
9801-099-002
9486-149-001
9545-053-002
T80
9021-041-001
9801-099-002
9486-149-001
9545-053-002
QTY
1
1
2
4
1
2
3 4 3 4
Part # 8533-088-001 7/21
105
106
Part # 8533-088-001 7/21
Part # 8533-088-001 7/21
107
30 lb. Commercial Dryer: T-30 – DC0030NB-10EC1X (60 Hz), DC0030NB-
39AC1X (50 Hz)
1835 mm.
Cabinet Height 72 1/4”
(Assumes minimum leveling leg adjustment)
Cabinet Width
Overall Depth
Floor to Door Center
Door Opening
31 1/2”
42”
41 1/4”
22 5/8”
30 lbs.
30”
27 1/2”
11.25 cu. ft.
Dry Wt. Capacity
Cylinder Diameter
Cylinder Depth
Cylinder Volume
Lint Screen Area
Gas Input (60 hz)
Gas Input (50 hz)
Gas Supply Connection
Natural Gas Supply (Water Column)
Natural Burner Manifold
515 sq. in.
90,000 Btu/hr
72,000 Btu/hr
1/2”
5-10”
3 1/2”
11 ½ -14” L.P. Supply (Water Column)
L.P. Burner Manifold
Exhaust Size
Make-up Air
11”
8”
1.0 sq. ft.
Example: 1.0 sq. ft = 1 ft. long X 1 ft. wide
Motor Size
Airflow (60 hz)
Airflow (50 hz)
1/2 H.P.
830 CFM
690 CFM
800 mm.
1067 mm.
1048 mm.
575 mm.
13.6 kg.
762 mm.
699 mm.
319 liters
3323 sq. cm.
26.4 kW
21.1 kW
12.7 mm.
127 mm. - 254 mm.
88.9 mm.
292 mm. - 356 mm.
279 mm.
203 mm.
929 sq. cm.
.373 kW
23.5 m^3/min
19.5 m^3/min
Electrical Specifications - 220-240/50/1
Voltage/Hz/Phase 220-240V/50Hz/1Phase
Running Amps
Circuit Protection Amps
Wire Size
Electrical Service
5.1
10
14 gauge
2 wire + ground
Shipping Weight
Net Weight 463 lbs. 210 kg.
Clearance Behind Machines (min.)
507 lbs.
18”
231 kg.
457 mm.
108
Part # 8533-088-001 7/21
Parts Section-39 & -59 230VAC 1 PH 50Hz
Key Description
Switch Assembly-Air flow (1-7)
1 Shield - Switch
2 Switch Micro
3 Nut - Twin, 4-40
4 Actuator-Switch, Air-Flow
5 Bracket-Airflow switch
6 Screw-PNHDSL, 4-40, UNC x
0.625
7 Pin-Cotter, 0.09375 x 0.75
T-30
9801-095-002
9550-169-003
9539-461-009
8640-401-001
9008-007-001
9029-174-002
9545-020-001
9451-169-002
T-50
9801-098-002
9550-169-003
9539-461-009
8640-401-001
9008-007-001
9029-200-002
9545-020-001
9451-169-002
T80
9801-098-002
9550-169-003
9539-461-009
8640-401-001
9008-007-001
9029-200-002
9545-020-001
9451-169-002
1
1
2
1
1
QTY
1
1
1
Part # 8533-088-001 7/21
109
Key Description T-30
* Motor, Marathon 50Hz
* Pulley, Motor
* Orfice Main Burner, #32
* Orfice Main Burner, #32
9376-311-004
9453-169-009
* Strip Terminal Marker 9558-029-004
* Wiring Label-Schematic/Diagram 9506-496-001
9425-069-009
* Orfice Main Burner, #30
* LP Kit
* Overlay-Trim Lower door
* Label Warning
9732-102-019
9435-016-004
8502-698-001
T-50
9376-317-004
9453-169-014
9558-029-004
9506-496-001
9425-069-009
9732-102-021
9435-016-005
8502-698-001
T80
N.A
N.A
N.A
N.A
N.A
N.A
N.A
N.A
N.A
QTY
1
1
1
1
2
3
1
1
4
1
110
Part # 8533-088-001 7/21
Part # 8533-088-001 7/21
111
112
Part # 8533-088-001 7/21
Part # 8533-088-001 7/21
113
Key Description
* Strip Terminal Marker
* Filter, MEI
* Transformer, Control
* Holder, Fuse
* Fuse 2.5 Amp
* Motor, Marathon 50Hz
N.A
N.A
* Pulley, Motor N.A
* Wiring Label-Schematic/Diagram N.A
* Orfice Main Burner, #30 Natural N.A
T-30
N.A
N.A
N.A
N.A
*
*
LP Kit
Gas Valve Assembly
* Kit-Honeywell VR86 Flange Kit
3/4
* Adaptor Assembly Gas Valve
* Manual, Operators
N.A
N.A
N.A
N.A
N.A
N.A
N.A
N.A
N.A
N.A
T-50
N.A
N.A
N.A
N.A
N.A
N.A
N.A
N.A
N.A
T80
9558-029-004
9183-030-001
8711-008-002
9054-045-001
8636-018-004
9376-317-004
9453-169-009
9506-644-001
9425-069-002
9732-102-030
9857-132-004
9732-162-002
9791-001-001
8514-234-002
1
1
1
1
2
1
1
1
1
4
1
1
QTY
1
1
114
Part # 8533-088-001 7/21
Part # 8533-088-001 7/21
115
116
Part # 8533-088-001 7/21
Part # 8533-088-001 7/21
117
118
Part # 8533-088-001 7/21
Part # 8533-088-001 7/21
119
Daily
Step 1: Clean the lint screen free of lint and other debris. Use a soft brush and Hot water if necessary.
Step 2: Check the lint screen for tears. Replace if necessary.
Step 3: Clean lint from the lint screen compartment.
Step 4: Inspect felt seal on lint screen assembly, replace if needed.
Monthly
Step 1: Remove lint accumulation from the end bells of the motor.
Step 2: Remove lint accumulation from front control area.
Step 3: Remove lint and dirt accumulation from the top of the dryer and all areas above, below, and around the burners and burner housing. Failure to keep this portion of the dryer clean can lead to a build-up of lint creating a fire hazard.
Step 4: Remove and clean coin acceptors. (Vended Models Only)
Quarterly
Step 1: Check the belts for looseness, wear, or fraying.
Step 2: Inspect the gasket of the door glass for excessive wear.
Step 3: Check tightness of all fasteners holding parts to support channel.
Step 4: Check tightness of all set screws.
Step 5: Remove the air flow switch assembly and check the tumbler thru-bolts for tightness.
Step 6: Apply a few drops of oil to pivot pins and the tension arms where in contact with each other.
Semi-Annually
Step 1: Remove and clean the main burners.
Step 2: Remove all orifices and examine for dirt and hole obstruction.
Step 3: Remove all lint accumulation. Remove the front panel and the lint screen housing and remove lint accumulation.
Annually
Step 1: Check the intermediate pulley bearings for wear.
Step 2: Check and remove any lint accumulation from the exhaust system including recirculation chambers if applicable.
Step 3: Grease the bearings and the shaft of the intermediate pulley. Use an Alemite grease gun and
Molykote BR2-S grease. (Where applicable)
120
Part # 8533-088-001 7/21
Part # 8533-088-001 7/21
121
122
Part # 8533-088-001 7/21
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Advertisement
Solid-state ignition
Multiple capacity models (30, 50, 80 lbs)
User-programmable cycles
Gas or LP models
Exhaust installation details
Electrical safety features
Make-up air requirements
USB programming
Do not try to light any appliance, do not touch any electrical switch, do not use any telephone in your building. Clear the room, building or area of all occupants. Immediately call your gas supplier from a neighbor’s telephone and follow their instructions. If you cannot reach your gas supplier, call the fire department.
If the gas fails to ignite after three tries, the gas valve closes and the system will "lock out". Interrupt electrical power to the ignition system before making another attempt to light the burners.
The electrical power requirements are listed on the serial plate and at the back panel of each dryer. The electrical connection should be made to the terminal block in the rear control box assembly, using a wire size adequate to handle the amperage and voltage listed on the serial plate. The dryer MUST be properly grounded.
For the most efficient operation, it is recommended that no more than 20’ (6m) of straight 8” diameter pipe be used with two right angle elbows.
Where can information regarding replacement parts for the dryer be found?
The "Dryer Parts Data" section details replacement parts for Dexter Commercial Vended Dryer C-Series models (T-30, T-50, and T-80). This section provides part numbers, quantities, and diagrams for major assemblies like the Cabinet Group, Dryer Tumbler Group, and Dryer Burner Housing Group.
Login to continue
