Ryobi ELS-52 Operator's Manual
Ryobi ELS-52 is a powerful electric log splitter designed to make splitting logs quick and easy. With its 1500W motor, it can generate up to 5 tons of splitting force, making it capable of handling even the toughest logs. It features a compact and portable design, allowing for easy storage and transportation. The ELS-52 is equipped with safety features such as a built-in log cradle to keep the log securely in place during splitting and a two-handed operation to prevent accidental activation.
Publicité
Publicité
ELS52
1500W ELECTRIC LOG SPLITTER
OPERATOR’S MANUAL (Original Instructions)
WARNING:
It is essential that you read the instructions in this manual before operating this machine.
14
ENGLISH (Original Instructions)
GENERAL SAFETY RULES
WARNING:
Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.
READ ALL INSTRUCTIONS
n KNOW YOUR POWER TOOL. Read the operator’s manual carefully. Learn the applications and limitations as well as the specific potential hazards related to this tool.
n GUARD AGAINST ELECTRICAL SHOCK BY
PREVENTING BODY CONTACT WITH GROUNDED
SURFACES. For example: pipes, radiators, ranges, refrigerator enclosures.
n KEEP GUARDS IN PLACE and in good working order.
n REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on.
n KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
DO NOT leave tools or pieces of wood on the tool while it is in operation.
n DO NOT USE IN DANGEROUS ENVIRONMENTS.
Do not use power tools in damp or wet locations or expose to rain. Keep the work area well lit.
n KEEP CHILDREN AND BYSTANDERS AWAY. All bystanders should wear safety glasses and be kept a safe distance from work area. Do not let bystanders contact tool or extension cord while the unit is in operation.
n Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
n DON’T FORCE THE TOOL.
It will do the job better and safer at the rate for which it was designed.
n USE THE RIGHT TOOL.
Do not force the tool or attachment to do a job for which it was not designed.
n USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. Use only a cord heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. n DRESS PROPERLY.
Do not wear loose clothing, neckties, or jewelry that can get caught and draw you into moving parts. Rubber gloves and nonskid footwear are recommended when working outdoors.
Also wear protective hair covering to contain long hair.
n ALWAYS WEAR SAFETY GLASSES WITH SIDE
SHIELDS THAT COMPLY WITH STANDARDS.
Everyday eyeglasses have only impact-resistant lenses, they are NOT safety glasses.
n DO NOT OVERREACH.
Keep proper footing and balance at all times.
n MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories.
n DISCONNECT TOOLS. When not in use, before servicing, or when changing attachments etc., all tools should be disconnected from power source.
n AVOID ACCIDENTAL STARTING. Be sure switch is off when plugging in any tool.
n USE RECOMMENDED ACCESSORIES. Consult the operator’s manual for recommended accessories. The use of improper accessories may result in injury.
n NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped.
n CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged must be properly repaired or replaced by an authorised service centre to avoid risk of personal injury.
n NEVER LEAVE TOOL RUNNING UNATTENDED. TURN
THE POWER OFF. Don't leave tool until it comes to a complete stop.
n PROTECT YOUR LUNGS. Wear a face or dust mask if the cutting operation is dusty.
n PROTECT YOUR HEARING. Wear hearing protection during extended periods of operation.
n DO NOT ABUSE CORD.
Never carry tool by the cord or pull on the cord to disconnect from receptacle. Keep cord from heat, oil, and sharp edges.
n USE OUTDOOR EXTENSION CORDS.
When tool is used outdoors, use only extension cords with approved ground connection that are intended for use outdoors and so marked.
n NEVER USE IN AN EXPLOSIVE ATMOSPHERE.
Normal sparking of the motor could ignite fumes.
n INSPECT TOOL CORDS PERIODICALLY.
If damaged, have repaired by a qualified service technician at an authorised service facility. Repair or replace a damaged or worn cord immediately. Stay constantly aware of cord location.
n INSPECT EXTENSION CORDS PERIODICALLY and replace if damaged.
n KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND
GREASE. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum-based products, or any solvents to clean tool.
n STAY ALERT AND EXERCISE CONTROL. Watch what you are doing and use common sense. Do not operate tool when you are tired. Do not rush.
n DO NOT USE TOOL IF SWITCH DOES NOT TURN IT
ON AND OFF. Have defective switches replaced by an authorised service centre.
n DO NOT OPERATE A TOOL WHILE UNDER THE
INFLUENCE OF DRUGS, ALCOHOL, OR ANY
MEDICATION.
n ALWAYS carry the tool only by the carrying handle.
n USE ONLY RECOMMENDED ACCESSORIES listed in this manual or addendums. Use of accessories that are not listed may cause the risk of personal injury. Instructions for safe use of accessories are included with the accessory.
5
ENGLISH (Original Instructions)
GENERAL SAFETY RULES
n TOOL SERVICE MUST BE PERFORMED ONLY
BY QUALIFIED REPAIR PERSONNEL. Service or maintenance performed by unqualified personal could result in a risk of injury.
n WHEN SERVICING use only identical replacement parts.
Use of any other parts may create a hazard or cause product damage.
n ALWAYS STAY ALERT!
Do not allow familiarity (gained from frequent use of your tool) to cause a careless mistake. ALWAYS REMEMBER that a careless fraction of a second is sufficient to inflict severe injury.
n MAKE SURE THE WORK AREA HAS AMPLE LIGHTING to see the work and that no obstructions will interfere with safe operation BEFORE performing any work using your tool.
n ALWAYS TURN OFF THE TOOL before disconnecting it to avoid accidental starting when reconnecting to power supply. NEVER leave the tool unattended while connected to a power source.
n DO NOT OPERATE IN POOR LIGHTING.
Use the unit only in daylight or good artificial light. n KEEP ALL BYSTANDERS especially children and pets, at least 3m from the operating area. n PULL THE PLUG OUT IMMEDIATELY if the mains or extension lead is damaged or severed.
SPECIFIC SAFETY RULES
n DO NOT ALLOW anyone to operate the log splitter who has not read the operator’s manual or has not been instructed on the safe use of the splitter.
n NEVER ALLOW CHILDREN OR UNTRAINED ADULTS
TO OPERATE THIS MACHINE.
n IF SOMEONE is helping load logs to be split, DO NOT start the machine until that person is clear of the area.
n NEVER ALLOW ANYONE TO RIDE ON THE
MACHINE.
n NEVER TRANSPORT ANYTHING OR ANYONE ON THE
LOG SPLITTER.
n HIGH FLUID PRESSURES ARE DEVELOPED IN
HYDRAULIC LOG SPLITTERS. Pressurized hydraulic fluid escaping through a pin hole opening can puncture skin and cause severe blood poisoning. Heed the following instructions at all times:
a) Do not operate the machine with frayed, kinked, cracked, or damaged hoses, fittings, or tubing.
b) Stop the engine and relieve hydraulic system pressure before changing or adjusting fittings, hoses, tubing, or other system components.
c) Do not adjust the pressure settings of the pump or value.
d) Never use your hand. Leaks can be located by passing cardboard or wood over the suspected area.
Look for discoloration. If injured by escaping fluid, see a doctor at once. Serious infection or reaction can develop if proper medical treatment is not adminis- tered immediately.
n KEEP THE OPERATOR ZONE and adjacent area clear for safe, secure footing.
n LOG SPLITTERS SHOULD BE USED ONLY for splitting wood. DO NOT use for other purposes unless the manufacturer provides attachments and instructions.
n MAKE SURE THE LOG SPLITTER is on a level surface.
Block the splitter as required to prevent unintended movement.
n ALWAYS OPERATE the splitter from the indicated operator zone.
n LOGS TO BE SPLIT ON RAM-TYPE UNITS should be cut as squarely as possible.
n THE MACHINE OWNER should instruct anyone assisting him or her in safe log splitting operation.
n ALWAYS operate the log splitter with all safety equipment in place and all controls properly adjusted for safe operation.
n ALWAYS operate the log splitter at the recommended speed.
n WHEN LOADING a ram-type log splitter, place your hands on the sides of the log not at the ends. NEVER place your hands or any part of your body between a log and any part of the log splitter.
n ON RAM-TYPE log splitters, NEVER attempt to split more than one (1) log at a time unless the ram has been fully extended and a second log is needed to complete the separation of the first log.
n ON RAM-TYPE log splitters on which the logs are not square, the longest portion of the log should be rotated down and the most square end placed against the ram.
n CLEAR DEBRIS from moving parts but only when the power source is shut off.
n USE ONLY YOUR HAND TO OPERATE THE LOG
SPLITTER CONTROLS.
n ALWAYS UNPLUG FROM THE POWER SOURCE while repairing or adjusting the splitter .
n CIRCUIT CAPACITY AND FUSES:
a) Use only an electrical circuit having adequate capacity. b) “Blowing” a fuse or tripping a circuit breaker is usually a warning that you are overloading the machine or have too many devices taking power from the circuit, or both. Do not install a higher capacity fuse!
n LEARN AND UNDERSTAND all controls and the proper use of the equipment.
n SAVE THESE INSTRUCTIONS.
Refer to them frequently and use to instruct other users. If you loan someone this tool, loan them these instructions also.
WARNING!
“Danger! Keep clear of moving parts!”
“To be operated by one person only!”
6
ENGLISH (Original Instructions)
SYMBOLS
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
Wet Conditions Alert
Read The Operator’s Manual
Eye Protection
Safety Alert
Wear Gloves
Wear Safety Footwear
Do not expose to rain or use in damp locations.
To reduce the risk of injury, user must read and understand operator’s manual before using this product.
Always wear safety goggles or safety glasses with side shields and a full face shield when operating this product.
Precautions that involve your safety.
Always wear nonslip, heavy-duty protective gloves when operating this product.
Always wear nonslip safety footwear when operating this product.
Keep Bystanders Away
Keep Hands Away
Always keep bystanders at least 10 ft. (3 m) away.
Always keep hands away from the wedge and the ram.
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER:
Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury.
WARNING:
Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
CAUTION:
(Without Safety Alert Symbol) Indicates a situation that may result in property damage.
7
ENGLISH (Original Instructions)
SYMBOLS
SERVICE
Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to your nearest
AUTHORISED SERVICE CENTRE for repair. When servicing, use only identical replacement parts.
WARNING:
To avoid serious personal injury, do not attempt to use this product until you read thoroughly and understand completely the operator’s manual. Save this operator’s manual and review frequently for continuing safe operation and instructing others who may use this product.
ELECTRICAL
EXTENSION CORDS
When using a power tool at a considerable distance from the power source, use an extension cord heavy enough to carry the current that the tool will draw. An undersized extension cord will cause a drop in line voltage, resulting in a loss of power and causing the motor to overheat.
When working with the tool outdoors, use an extension cord that is designed for outside use.
Before using an extension cord, inspect it for loose or exposed wires and cut or worn insulation.
WARNING:
Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on timber, tools or other obstructions while you are working with a power tool. Failure to do so can result in serious personal injury.
GROUNDING INSTRUCTIONS
In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current. To reduce the risk of electric shock, this tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified electrician.
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.
Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded.
Repair or replace a damaged or worn cord immediately.
WARNING:
Check extension cords before each use. If damaged replace immediately. Never use tool with a damaged cord since touching the damaged area could cause electrical shock resulting in serious injury.
ELECTRICAL CONNECTION
This tool is powered by a precision built electric motor. It should be connected to a power supply that is 230 volts,
50 Hz, AC only (normal household current). Do not operate this tool on direct current (DC). A substantial voltage drop will cause a loss of power and the motor will overheat. If the product does not operate when plugged into an outlet, double check the power supply.
Connect the main leads to a standard 230V±10%
(50Hz±1%Hz) electrical supply which has protection devices of under-voltage, over-voltage, over-current as well as a residual current device (RCD) which maximum residual current rated at 0.03A, the main connection must have maximum
10A time-lag fuse.
8
ENGLISH (Original Instructions)
FEATURES
PRODUCT SPECIFICATIONS
Maximum Hydraulic Cylinder Pressure ...................16 MPa
Force .......................................................................... 4tons
Oil Capacity ................................................................. 3.5 L
Voltage ........................................................... 230 V~50 Hz
In Put Power ............................................................1500 W
No Load Speed ..........................................2970±10% rpm
Measured sound power level ....................... L
WA
80.8 dB(A)
K
WA
3.0 dB(A)
Measured sound pressure level ....................L
PA
68.6 dB(A)
K
PA
3.0 dB(A)
Net Weight ..................................................................49 Kg
Log Capacity Diameter, maximum ..........................250mm
Log Capacity Diameter, minimum ...........................100mm
Log Capacity Length ...............................................520mm
Vibration ..................................................................2.5m/s 2
DESCRIPTION
1. Bleed screw
2. Hydraulic control lever
3. Ram
4. Oil drain bolt with dipstick
5. Side supports
6. Push button box
7. On / Off switch
8. Lift handle
9. Axle
10.Hitch pin
11.Washer
12.Dip stick
13.Level indicator marks
14.Wood wedge
15.Reset button
16.Work table
17.Wedge
PACKING LIST
1 x Log splitter
1 x Manual
2 x Wheel
2 x Axle
4 x Washer
2 x Hitch pin
KNOW YOUR LOG SPLITTER
( Fig.1)
Before attempting to use this product, familiarise yourself with all operating features and safety rules.
BLEED SCREW
Loosen the bleed screw (1) to ensure the smooth flow of air in and out of the oil tank.
HYDRAULIC CONTROL LEVER
Push down on the hydraulic control lever (2) and the ram(3) starts pushing the log into the wedge (17).
LIFT HANDLE
The lift handle (8) makes rolling the log splitter from one location to another simple and easy.
RESET/OVERLOAD BUTTON
If the motor is overloaded the machine will shut off. Remove the load and push the reset/overload button (15) to restart the machine.
OIL DRAIN BOLT WITH DIPSTICK
Oil drain bolt with dipstick (4) makes checking and changing hydraulic oil easy.
SIDE SUPPORTS
Side supports (5) on each side of the work table (16) keep logs resting securely on the log splitter.
WORK TABLE
Provides surface to support log prior to splitting operation.
ASSEMBLY
UNPACKING
n Carefully remove the tool and any accessories from the box. Make sure that all items listed in the packing list are included.
n Inspect the tool carefully to make sure no breakage or damage occurred during shipping.
n Do not discard the packing material until you have carefully inspected and satisfactorily operated the tool.
WARNING:
Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.
WARNING:
Do not connect to power supply until assembly is complete. Failure to comply could result in accidental starting and possible serious personal injury.
WARNING:
If any parts are missing do not operate this tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury.
9
ENGLISH (Original Instructions)
ASSEMBLY
WARNING:
Failure to loosen the bleed screw prior to operation of this product may cause the seals in the hydraulic system to blow out. Blown seals could cause permanent damage to the log splitter.
ASSEMBLING THE WHEELS (Fig 2.)
To attach the wheels to the base: n Locate the axle (9) assembly; remove the hitch pin (10) from the axle.
n Lift the machine slightly and slip the axle into the wheel hole.
n Next, slide the washer (11) onto the axle. Still lifting the machine, slide the axle/wheel/washer combination into the wheel mounting hole in the machine base as shown in fig 2.
n Slide the washer onto the axle. Push the hitch pin into the hole on the end of the axle to secure the wheel assembly.
NOTE: The hitch pin should be pushed into the axle until the centre of the pin rests on top of the axle.
n Repeat with the second wheel assembly.
OPERATION
WARNING:
Do not allow familiarity with tools to make you careless.
Remember that a careless fraction of a second is sufficient to inflict serious injury.
WARNING:
Always wear safety goggles or safety glasses with side shields when operating this tool. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury.
WARNING:
Do not use any attachments or accessories not recommended by the manufacturer of this tool. The use of attachments or accessories not recommended can result in serious personal injury.
BEFORE USING THE LOG SPLITTER
( See Fig 3-4)
Never operate the log splitter until the bleed screw (1) has been slightly loosened (one to two full turns). Air flow through the bleed screw should be detectable once the log splitter is started. If no air flow is detected, loosen the screw until the air flow can be felt.
Air must flow in and out of the oil tank during operation to prevent the seals in the hydraulic system from rupturing.
This tool is designed for home use only. Never split logs larger than 25cm. diameter or 52cm. long. Some types of wood are harder to split than others. If the log splitter is having trouble splitting a log, never continue to try for longer than five seconds.
Always check the oil level before you start the log splitter.
To check the oil level: n Unplug the log splitter.
n Using the lift handle (8), stand the log splitter on the end with the wheels (see fig.11).
n Using an 8 mm hex key, remove the oil drain bolt and wipe the dipstick clean.
n Wipe the dipstick clean then reinsert it back into the oil tank.
n Remove the dipstick (12) and check to see if the oil level is between the first and second groove on the dipstick
(Fig.4).
n If there is not enough oil in the oil tank, add oil until the proper level is reached.
n If there is the proper amount of oil in the oil tank, wipe the dipstick clean then replace it in the oil tank and tighten the oil drain bolt securely.
NOTE: See “Replacing Hydraulic Oil” in the Maintenance section for recommended oil or equivalents.
STARTING THE LOG SPLITTER
( See Fig 5 - 6).
n Operator should be positioned at the rear of the log splitter as shown in figure (6).
n Place the left hand on the hydraulic control lever (2) and the right hand on the on/off switch (7).
n Push down and hold the on/off switch.
n While continuing to hold down the on/off switch, push down and hold the hydraulic control lever.
NOTE: Both hands are required to start this product. The combination of both steps starts the ram which pushes the log into the wedge.
n To stop the splitter, release both controls to return the ram to the starting position.
NOTE: If only one hand is removed from either the switch or the lever, the log splitter will freeze in place. When both the switch and the lever are released, the ram will return to the starting position.
10
ENGLISH (Original Instructions)
OPERATION
SPLITTING LOGS
(See Fig.7 - 8).
Always place logs lengthwise on the work table and resting firmly on the side supports. Place logs flat and in the direction of the grain. Never angle the log to split it or place the log crosswise on the splitter. Never split more than one log at a time.
CAUTION:
Never keep pressure on the wood by trying to force the log splitter for more than five seconds. After five seconds, the oil will heat and can damage the tool.
n Place log lengthwise and lying flat on the work table.
NOTE: If the log is small, place it against the wedge before starting the splitter.
n Using the right hand, push down and hold the on/off switch.
n Push down and hold the hydraulic control lever with the left hand. With both the lever and the on/off switch activated, the ram will push the log into the wedge and split the wood.
n Once the log is split, release both controls to return the ram to the starting position.
FREEING A JAMMED LOG
(See Fig.9 - 10.) n Release both controls.
n After the ram is back at the starting position, insert a wood wedge under the jammed log.
n Start the log splitter to push the wood wedge (14) completely under the jammed log.
n If the log is still jammed, repeat the above steps as needed using a thicker angled wood wedge until the log is completely freed.
NOTE: Never try to knock the jammed log off the splitter.
Doing so may damage the tool or may cause the log to fly up and hit someone causing injury.
MAINTENANCE
WARNING:
When servicing, use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage.
WARNING:
Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a dust mask.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline, petroleumbased products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.
REPLACING HYDRAULIC OIL
(See Fig.11-12)
When new your Ryobi log splitter is supplied with the correct amount of hydraulic oil. The hydraulic oil in the log splitter needs to be changed every 150 hours of use.
The recommended grade of hydraulic oil is 22 weight. For extreme cold environments use 32 weight oil. The unit will carry approximately 3.5l of oil when fully emptied. (Use the dipstick for correct fill).
n Unplug the log splitter.
n Position the log splitter so that the motor end is slightly higher than the oil drain plug. (Fig.12) n Using an 8 mm hex key, remove the oil drain bolt.
n Drain the hydraulic oil from the oil tank into a four litre capacity container.
n Once the oil has drained from the oil tank, turn the log splitter on the end with the wheels. (Fig.11) n Refill the oil tank with fresh hydraulic oil (3.5L). n Place the cleaned dipstick into the oil tank. Remove and check the oil level.
NOTE: The oil level should be between the two oil lines around the bottom of the dipstick as shown in figure 4.
n Replace oil drain bolt. Tighten securely.
n Dispose old oil at an oil recycling centre.
LUBRICATION
All of the bearings in this tool are lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions. Therefore, no further lubrication is required.
11
SHARPENING THE WEDGE
After using the log splitter for some time, it may be necessary to sharpen the wedge. Using a fine-toothed file, smooth any burrs or crushed areas along the cutting edge.
PROBLEM
Motor fails to start
Won’t split logs
ENGLISH (Original Instructions)
TROUBLESHOOTING
POSSIBLE CAUSE
1. Overload Protection Device is engaged to protect the log splitter from being damaged.
1. Log is improperly positioned.
2. The size or hardness of the log exceeds the machine’s capacity.
3. Wedge cutting edge is blunt.
Log mover jerks and vibrates
Oil leaks around cylinder ram or from other points
4. Oil leaks.
5. Unauthorised adjustment was made on the Maximum Pressure
Limiting Screw. Lower maximum pressure rating was set.
1. Lack of hydraulic oil and excessive air in the hydraulic system.
1. Air sealed in hydraulic system while operating.
2. Bleed screw is not tightened before moving the log splitter.
3. Oil drain bolt is not tight.
4. Hydraulic control valve assembly and/or seal(s) are worn.
SOLUTION
1. Push reset button (15).
See fig 13
1. Refer to Operation section for log loading.
2. Reduce the log size before splitting.
3. Refer to “Sharpening Wedge” in the
Maintenance section.
4. Locate leak(s). Contact the dealer.
5. Contact authorised service centre.
1. Check oil level for possible oil refilling. Contact the dealer.
1. Loosen bleed screw by 3-4 rotations before operating the log splitter.
2. Tighten the bleed screw before moving the log splitter.
3. Tighten the oil drain bolt.
4. Contact the dealer.
12
LIMITED WARRANT
TTI warrants this outdoor product to be free of defects in material and workmanship for 24 months from the date of purchase by the original purchaser, subject to the limitations below. Please keep your invoice as proof of date of purchase.
This warranty is only applicable where the product is used for personal and non-commercial purposes.
This warranty does not cover damage or liability caused by / due to misuse, abuse, accidental or intentional acts by user, improper handling, unreasonable use, negligence, failure by end user to follow operating procedures outlined in the user’s manual, attempted repair by non-qualified professional, unauthorized repair, modification, or use of accessories and/or attachments not specifically recommended by authorized party. Please see your local dealer for list of authorized service centers in your area.
This warranty does not cover belts, brushes, bags, bulbs or any part which ordinary wear and tear results in required replacement during warranty period. This warranty does not cover transportation cost or consumable items such as fuses and batteries.
This limited warranty is void if the product’s original identification (trade mark, serial number, etc.) markings have been defaced, altered or removed or if product is not purchased from an authorized reseller or if product is sold AS IS and / or WITH ALL FAULTS.
Where permitted, the provisions of this limited warranty are in lieu of any other written warranty, whether express or implied, written or oral, including any warranty of MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL WE BE
LIABLE FOR SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES. OUR MAXIMUM LIABILITY SHALL NOT
EXCEED THE ACTUAL PURCHASE PRICE PAID BY YOU FOR THE PRODUCT.
This warranty is applicable only in the European Union, Australia, and New Zealand. Outside these areas, please contact your authorized Homelite dealer to determine if another warranty applies.
TECHTRONIC INDUSTRIES EMEA
Medina House, Field House Lane,
Marlow, Bucks
SL7 1TB - United Kingdom
RYOBI TECHNOLOGIES (UK) LIMITED
Medina House, Field House Lane,
Marlow, Bucks
SL7 1TB - United Kingdom
Tel: + 44 (0) 1628 894400
Fax: + 44 (0) 1628 894401
Technical Helpline : + 44 (0) 800 389 0305
TECHTRONIC INDUSTRIES FRANCE SAS
Immeuble Le Grand Roissy
Z.A. du Gué - 35 rue de Guivry
77990 Le Mesnil Amelot France
Phone: + 33(0)1 60 94 69 70
Fax: + 33(0)1 60 94 69 79
RYOBI BELGIUM
Avenue des Pâquerettes, 55
Zoning artisanal - bâtiment 5
B - 1410 Waterloo
Belgique
Tel : + 32(0) 2357 8140
Fax : + 32(0) 2357 8149
TTI ITALIA SRL
Via Fratelli Gracchi, 39
20092 Cinisello Balsamo (MI)
Italia
Tel : + 39 02 37050440
Fax : + 39 02 37050444
TECHTONIC INDUSTRIES IBERIA S.L
Av. De la Industria, 52
Coslada – Madrid – España
Tel: 91 485 12 10
TECHTRONIC INDUSTRIES SOUTH AFRICA
CO. (PTY) LTD
P.O Box 83888, South Hills,
Johannesburg, 2136
South Africa
TECHTRONIC INDUSTRIES (ASIA) CO., LTD.
24/F, CDW Building,
388 Castle Peak Road,
Tsuen Wan, Hong Kong
Tel : + 852 2402 6888
TECHTRONIC INDUSTRIES CENTRAL EUROPE GMBH
Itterpark 2
D-40724 Hilden
Deutschland
Tel: + 49 (0)960-0
Fax: + 49 (0) 960-238
Machine: 1500W ELECTRIC LOG SPLITTER
Name of company: Homelite Far East Co., Ltd.
Address: 24/F, CDW Building,
388 Castle Peak Road,
Tsuen Wan Hong Kong.
TECHTRONIC INDUSTRIES
AUSTRALIA PTY LIMITED
Building B, Rosehill Industrial Estate,
3 Shirley Street,
Rosehill NSW 2142
Australia
Tel: (02) 8892 1800 or 1300 361 505
Fax: 1800 807 993
TECHTRONIC INDUSTRIES (NZ) LIMITED
27 Clemow Drive, Mt Wellington
PO Box 12-806, Penrose, Auckland
New Zealand
Tel: + 64 (0) 9 573 0230
Free Call: +64 0800 279 624
Fax: + 64 (0) 9 573 0231
A&M MIDDLE EAST FZCO
P.O.Box 61254
Jedel Ali, Dubai
United Arab Emirates
Tel.: + 9714 8861399
Fax: + 9714 8861400
TECHTRONIC INDUSTRIES DENMARK APS
Stamholmen 147, 4
DK-2650 Hvidovre
Denmark
Tlf 43 56 55 55
Fax 43 56 55 56
E-mail: [email protected]
TECHTRONIC INDUSTRIES NORWAY AS
Stamholmen 147, 4
DK-2650 Hvidovre
Denmark
Tlf.: (+47) 800 12 493
Faks: (+47) 800 12 492
E-mail: [email protected]
TECHTRONIC INDUSTRIES SWEDEN AB
Stamholmen 147, 4
DK-2650 Hvidovre
Denmark
Tel (+46) 08 24 60 30
Fax (+46) 08 24 60 31
E-mail: [email protected]
TECHTRONIC INDUSTRIES FINLAND OY
Stamholmen 147, 4
DK-2650 Hvidovre
Denmark
Tel. 0800 1 09000
Fax 0800 1 09001
E-mail: [email protected]
Type: ELS52
Name / title: Andrew John Eyre BEng CEng MIET
Vice President of Engineering
Signature:
8 / 2010
Télécharger
Lien public mis à jour
Le lien public vers votre chat a été mis à jour. Vous pouvez afficher et gérer vos liens de chat après inscription ici.
Lien public du document
Publicité