b
Network Communications Guide
Compaq D315
Document Part Number: 287936-002
July 2002
This guide provides definitions and instructions for using network interface controller (NIC) features that are preinstalled on select desktop models.
© 2002 Compaq Information Technologies Group, L.P.
Compaq and the Compaq logo are trademarks of Compaq Information
Technologies Group, L.P. in the U.S. and other countries.
Microsoft, Windows, and Windows NT are trademarks of Microsoft
Corporation in the U.S. and other countries.
All other product names mentioned herein may be trademarks of their respective companies.
Compaq shall not be liable for technical or editorial errors or omissions contained herein. The information in this document is provided “as is” without warranty of any kind and is subject to change without notice. The warranties for
Compaq products are set forth in the express limited warranty statements accompanying such products. Nothing herein should be construed as constituting an additional warranty.
Å
WARNING: Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life.
Ä
CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information.
Network Communications Guide
Compaq D315
Second Edition (July 2002)
Document Part Number: 287936-002
Contents
Network Communications Guide
Wake-On-LAN Support (WOL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1
Interpreting the Network Status Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2
Disabling 802.3u Auto-Negotiation Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2
Installing Network Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–3
Network Communications Guide iii
Contents iv Network Communications Guide
Network Communications Guide
The following items are covered in this guide:
■
■
■
■
Wake-On-LAN (WOL) Support
Interpreting the Network Status Lights
Disabling 802.3u Auto-Negotiation Capabilities
Installing Network Drivers
✎
This platform has been configured with a PCI NIC to provide enhanced performance. Please ensure that you connect your network cable to the standard RJ-45 port located on the PCI card.
Wake-On-LAN Support (WOL)
Wake-On-LAN (WOL) can be enabled and disabled in Windows
2000 and Windows XP.
To enable or disable Wake-On-LAN:
1. Select Device Manager > NIC > Properties.
2. Select the Power Management tab.
3. Select or de-select Allow this Device to Bring the Computer out of Standby .
Or,
1. Run Computer Setup and select Device Options from the
Advanced menu.
2. Set PME wakeup events to enable/disable.
Network Communications Guide 1
Network Communications Guide
✎
For more information on Wake-On-LAN, refer to the online Desktop
Management Guide or to the Remote Management Administrators
Guide.
The Remote Management Administrators Guide is included with the Remote Management Setup Utilities and is available on the
Support Software CD for Compaq Desktop, Portable, and
Workstation Products or at the Compaq Web site at www.compaq.com.
✎
For information on WOL filtering, refer to any additional documentation provided for the NIC’s advanced diagnostics/configuration utility.
2
Interpreting the Network Status Lights
Select Ethernet network interface controllers include network status lights:
■ The link light illuminates when the system is physically connected to an active network.
■ The activity light illuminates when the computer detects network activity. When the system is connected to a highly used network, the activity light will remain on almost constantly.
■ The 100Base-TX light illuminates during 100-Mbs operation.
Some NICs include only two network status lights where link (light on) and activity (light blinking) are indicated by one light and
100-Mbs operation is indicated by the second light.
Disabling 802.3u Auto-Negotiation Capabilities
Auto-Negotiation NICs automatically determine the maximum network operating speed and duplex capabilities of the attached network and configure themselves on the highest common combination. The computer begins Auto-Negotiation whenever it obtains a valid network link, or when the NIC driver is loaded.
In addition to determining the network operating speed, the computer determines if full-duplex is supported. Full-duplex systems can transmit and receive information on the network simultaneously.
Half-duplex systems cannot transmit and receive simultaneously.
Network Communications Guide
Network Communications Guide
If necessary, you can disable the Auto-Negotiation capabilities and force the system to operate in one mode only.
1. Select the Network icon, located in the Control Panel.
2. Select the appropriate NIC in the list box and click Properties.
3. Change the Speed and Duplex values from Automatic/Auto
Duplex to the appropriate values, depending on the capabilities of your network.
4. Exit the Network control application. You will be prompted to restart your computer for the changes to take effect.
Refer to the documentation provided with the network controller for additional information.
✎
100Base-TX operation requires the use of Category 5 UTP cable with an RJ-45 network connection.
Installing Network Drivers
The device drivers for the network controller enable the drivers to load correctly in the operating system used, allowing communication with the network.
✎
Device drivers are supplied for the Microsoft Windows 2000 and
Windows XP operating systems, depending on the computer model.
If you are using another operating system, device drivers may be installed from media included with the network operating system or are available from Compaq. If reinstallation of the operating system ever becomes necessary, use the Compaq Restore Plus!
CD.
Network Communications Guide 3
