Grundig DSR 1510 Owner Manual

DIGITAL

SATELLITE

RECEIVER

DSR 1510

DEUTSCH

ENGLISH

2

CONTENTS

____________________________________________

4

4

4

5

6

General information

Packing contents

Digital satellite reception

Special features of your digital receiver

Set-up and safety

7-9

7

8

9

10-11

10

10

10

11

11

11

11

12-21

12

13

14

15

16

17-18

19

20-21

Overview

The front of the digital receiver

The back of the digital receiver

The remote control

Connection and preparation

Connecting the satellite antenna

Connecting the television

Connecting a video recorder

Connecting an AV receiver or hi-fi system

Connecting a digital multi-channel amplifier

Connecting the power cord

Inserting batteries in the remote control

Settings

The menu

Assigning preset stations

Editing the station list

Editing the list of favourite stations

Setting the local time

Adjusting the digital receiver to the television set

Adjusting the digital receiver to the LNB configuration of the satellite antenna

Audio settings

22-24 Basic functions

22

22

22

22

Switching on and off

Mode selection

Selecting preset channels

Adjusting the volume

23

23

23

24

Muting the sound

Selecting stations from lists

Switching from the current station to the previous one

TV Guide

24 Subtitles

25-26

25

25-26

Teletext mode

Teletext

Additional functions

27-31

27

27

28

28

29

30-31

32-33

32

32

33

34-36

34

34

34

35

35

36

CONTENTS _________________________________________________

Additional functions

Setting the menu language

Deleting stations automatically

Preset satellite stations

Automatic station search

Manual station search

Timer functions

Special settings

Resetting the digital receiver to its original state

Updating the digital receiver software

Selecting the remote control level

Information

Displaying station reception properties

Displaying device information

Connecting the digital receiver to a PC

Technical data

Environmental note

Troubleshooting

3

4

GENERAL INFORMATION

__________________

Packing contents

1 DSR 1510 Digital Satellite Receiver

2 Tele Pilot 766 S remote control

3 Two batteries for the remote control (2 x 1.5 V, Mignon, e.g.

UM-3 or AA)

4 Euro/AV (Scart) cable

5 Power cord

6 Operating manual

Digital satellite reception

In order to use your new DSR 1510 digital receiver you need a digital-compatible satellite antenna, which must be installed and aligned to the required satellites (for example Astra and

EutelSat/Hotbird).

Unlike analogue satellite broadcasting, digital TV or radio stations are not all assigned their own frequencies; instead, several TV and/or radio are “transmitted” by a single transponder.

To help you with the choice and settings for satellite stations, a selection of TV and radio stations have already been programmed for you. So that all the satellite stations that have since gone on air are available to you, you can start a station search.

To find out how it works and what you have to do, read page 26 of this manual.

Of course, you can easily program “new” stations yourself. You can find the latest transponder information on the teletext pages of various broadcasters, in a current satellite TV magazine or on the internet.

GENERAL INFORMATION ______________________________

Special features of your digital receiver

The DSR 1510 digital receiver can receive and process all unencrypted digital satellite stations.

This digital receiver has a built-in digital receiver unit for satellite stations. The receiver unit converts the signals from digital satellite stations to provide outstanding audio and picture quality.

To ensure that your digital receiver always uses the latest station information and operating software, you must first perform an update.

Using the Astra 19.2° East satellite, you can update the device software of the satellite receiver.

To find out how it works and what you have to do, read page 32 of this manual.

The TV guide also tells you of any schedule changes at short notice, and provides an overview of all the stations’ schedules for the next few hours.

You can call up detailed information on each TV programme at the touch of a button.

This digital receiver has a very comprehensive, user-friendly menu system.

The menu is displayed on the television screen, and the functions of the remote control buttons are explained.

5

6

°

C

°

C

DSR 1510 DIGITAL SATELLITE RECEIVER



2h


Krieg im Balkan

SET-UP AND SAFETY

___________________________

To ensure that that this high quality, easy-to-use digital receiver gives you lasting entertainment and enjoyment, please note the following information.

This digital receiver is designed to receive, record and play back video and audio signals. Any other use is expressly prohibited.

When setting up the digital receiver, make sure it is in a horizontal position and that the mains socket is easily accessible.

Please note when setting up the digital receiver that furniture surfaces are coated with various types of paint and plastic, which often contain chemical additives. These additives may cause corrosion to the feet of the unit. This may leave stains on the surface of the furniture which can be difficult or impossible to remove.

If the digital receiver is subject to a sudden change in temperature, for example when brought in from the cold to a warm room, let it stand for at least two hours before you connect it to the mains supply.

Do not expose the digital receiver to any moisture.

The digital receiver is designed for use in dry rooms. If you do use it outdoors, please ensure that it is protected from moisture, such as rain or splashing water. Do not place any vessels such as vases on the digital receiver. These may be knocked over and spill fluid on the electrical components, thus presenting a safety risk.

Do not place the digital receiver close to heating units or in direct sunlight, as this will impair cooling. Place the digital receiver on a hard, level surface. Do not lay any objects such as magazines on the digital receiver. When placed in a cabinet, make sure there is a minimum space of 10 cm around it.

Thunderstorms are a danger to all electrical devices. Even if the digital receiver player is switched off, it can be damaged by a lightning strike to the mains or the antenna.

Always disconnect the mains and antenna plugs during a storm.

Never open the digital receiver casing under any circumstances.

Warranty claims are excluded for damage resulting from improper handling.

Note:

Do not connect any other equipment while the device is switched on. Switch off the other equipment as well before connecting it.

Only plug the device into the mains socket after you have connected the external devices and the antenna.

OVERVIEW

____________________________________________

The front of the digital receiver


Ǽ

Switches the digital receiver to standby mode and off again.

•

(red) Lights up: The digital receiver is in standby mode.

Flashes: No input signal.

7

8

OVERVIEW _________________________________________________

The back of the digital receiver

INPUT SAT

AUDIO OUT

L R

Antenna socket for the satellite antenna.

Left/right stereo sockets (cinch) for hi-fi system.

VIDEO OUT

230-240V~

50/60 Hz 12 W

Video signal output socket (FBAS) for television or AV receiver.

DIGITAL

AUDIO OUT

RS 232

Audio output sockets for digital audio signal (cinch) for digital multi-channel amplifier.

EURO AV 2 ɮ VCR Euro AV socket (input and output) for the video recorder.

EURO AV 1 ɮ TV Euro-AV (output) socket for the television.

Serial interface for connecting to a PC.

Connection socket for the power cord supplied.

Note:

The model designation can be found on the back of the digital receiver.

PIP z

TXT

TV

TV-G

MHP A/B

Radio d

DR

TV

DVD

Tele Pilot 766 S

OVERVIEW ________________________________________________

P+

P-

OK

TXT

TV-G

TV

RADIO

Ȅ

ǷǷ

F

DR, TV

DVD

The remote control

Ǽ

Switches the digital receiver to standby, and from standby to the channel last selected.

E

?

1 ... 0 d

Calls up the device connections menu.

Displays programme information.

Select stations.

i

Switches the sound to mute and on again.

Opens the main menu.

z Switches between the two most recently selected channels.

Adjust the volume.

Switch channels up and down one by one.

Opens the station list.

Switches between teletext and TV modes.

Calls up the TV guide.

Switches to TV mode.

Switches to radio mode.

Opens the »Record timer« menu.

Opens the »Subtitles« menu.

Opens the »Sound« menu.

Switches to operating a second GRUNDIG digital receiver, GRUNDIG television or

GRUNDIG DVD player.

Keep the appropriate button (» DR «, » TV «, » DVD «) pressed down. Then press the required button.

Note:

The functions available depend on the model of the device you are using.

Just try it out.

9

10

CONNECTION AND PREPARATION

__

SAT

12

7

L

R

AV2

AV1

L

O

U

T

R

AUDIO

L

N

I

R

DEC. - AV 2

EURO - AV 1 ń

Connecting the satellite antenna

1 Connect the antenna cable of the satellite antenna to the » INPUT SAT « socket on the digital receiver (screw connector, F connector).

Connecting the television

1 Plug the Euro-AV (Scart) cable supplied into the » EURO AV1 ɮ TV « socket on the digital receiver and the corresponding Euro-AV socket

(e.g. EURO-AV, SCART) on the television.

Connecting a video recorder

1 Plug a standard Euro-AV (Scart) cable into the » EURO AV2 ɮ VCR « socket on the digital receiver and the Euro-AV socket (e.g. EURO-AV,

LINE IN/OUT, EXT.1) on the video recorder.

Note:

When playing back a video recording, the video and audio signal from the video recorder is automatically looped through to the television via the » EURO AV1 ɮ TV « socket on the digital receiver.

It may not be switched off by the power switch.

CONNECTION AND PREPARATION _________________

Connecting an AV receiver or hi-fi system

1 Plug a standard cinch cable into the » VIDEO OUT « and

» AUDIO OUT L R « sockets (left/right) on the digital receiver and the corresponding input sockets on the AV receiver or hi-fi system.

Connecting a digital multi-channel amplifier

1 Plug a standard cinch cable into the » DIGITAL AUDIO OUT « socket on the digital receiver and the corresponding socket on the digital multichannel amplifier.

Connecting the power cord

1 Plug the power cord supplied into the » 230-240V~ 50/60Hz « socket on the digital receiver.

2 Plug the power cord into the wall socket.

Note:

Only plug the device into the mains socket after you have connected the external devices and the antenna.

Inserting batteries in the remote control

1 Open the battery compartment by removing the lid.

2 Insert the batteries (Mignon type, for example UM-3 or AA, 2 x 1.5 V).

Observe the polarity (marked on the base of the battery compartment).

3 Close the battery compartment.

Note:

If the digital receiver no longer reacts properly to remote control commands, the batteries may be flat. Be sure to remove used batteries.

The manufacturer accepts no liability for damage resulting from leaking batteries.

Environmental note

Batteries, including those which contain no heavy metal, may not be disposed of with household waste. Please dispose of used batteries in an environmentally sound manner. Find out about the legal regulations which apply in your area.

11

12

SETTINGS

______________________________________________

Main Menu

Settings

Channel lists

Program information

Timer

Installation

Select and open

Back Exit

The menu

This digital receiver has a very comprehensive, user-friendly menu system. The menu is displayed on the television screen.

The digital receiver responds to many functions which you select on the remote control with informative menus and icons on the television screen.

It enables you to select many different settings and contains information on using your digital receiver.

The buttons on the remote control for using the menu are explained on the screen.

The main menu contains the most important controls for your digital receiver. Its menu system controls the dialogue between you and the digital receiver.

Press » i « to open the main menu. Press » P« or » P+ « to navigate the menu and select items. The selected item is highlighted.

When you press » OK « to confirm your selection, a sub-menu appears. Here too, you can navigate by pressing » P« or » P+ « and select the item you want. The selected item is highlighted.

Press » OK « to confirm. Normally another menu then appears, where you can use » P« or » P+ « to navigate and make the setting.

Make settings using » P«, » P+ «, »

Ǹ

« or »

Ƿ

«.

Press » z « to quit the current menu level.

Press » i « to quit the menu entirely.

SETTINGS _________________________________________________

Menüsprache

Deutsch

English

Français

Italiano

Español

Suomi

Svenska

Polski

Auswählen und bestätigen

Country

Germany

Austria

Spain

Italy

Select and confirm

Back

Satellite

Astra 19.2

Hot Bird

Sirius 2/3

Amos 1

Hellas Sat 2

Turksat 1C

Select and confirm

Back

Switzerland

Poland

Assigning preset stations

The digital receiver is already programmed with the stations from the Astra 19.2° East, Eutelsat/Hot Bird 13° East , Turksat 1C, Sirius

2/3, Amos and Hellas Sat 2 satellites.

The following settings allow you to select the menu language, the country where you are operating the digital receiver and the main satellites.

Selected stations from the chosen satellites are transferred to the list of favourites. You can then sort the stations in the order you require.

1 Switch on the digital receiver by pressing »

Ǽ

« on the receiver.

– The »Language« menu appears when the device is first switched on.

2 Select your language using » P« or » P+ « and press » OK « to confirm.

– The »Country« menu appears.

3 Press » P« or » P+ « to select the country and press » OK « to confirm.

– The »Satellite« menu appears.

4 Select the main satellites with » P« or » P+ « and press » OK « to confirm.

– The stations are added to the station list.

– The stations of the other satellites are added to the station list after you set the main satellite.

– After the data is transferred, the receiver switches to preset station 1.

– You can change the order of the preset stations as required and delete stations you do not need (see the section on editing the station list on page 14).

13

14

SETTINGS _________________________________________________

Edit Channel Lists

Channel list

Favorites

Select and open

Back

Edit Channel Lists

1 Sat 1

2 ProSieben

3 KABEL1

4 NEUN LIVE Telev

5 DSF

6 HSE24

7 SAT.1

8 N24

9 TELE 5

10 Das Erste Astra 19.2

Select and mark

Back

Delete

Exit

Move

Exit

Editing the station list

You can change the order of preset stations as required and delete stations you do not need.

1 In the main menu, select »Channel lists« with » P+ « or » P« and press » OK « to confirm.

2 Select »Channel list« by pressing » OK «.

– The station list appears.

Deleting stations

1 Press » P« or » P+ « to select the station to delete and press

» OK « to confirm.

– The station is highlighted in orange.

2 Select the next station with » P« or » P+ « and press » OK « to confirm.

3 Press » z « to delete the stations.

– The highlighted stations are deleted.

Moving stations

1 Press » P« or » P+ « to select the station to move and press




3 Press » P« or » P+ « to select the channel in front of which the station is to be inserted.

4 Press »

ǷǷ

« to move the stations.

Ending the settings

1 Press » i « and then » OK « to save the settings.

SETTINGS _________________________________________________

Edit Channel Lists

Channel list

Favorites

Select and open

Back

Edit Favorites

A: Channel lists

1 Sat 1

2 ProSieben

3 KABEL1

4 NEUN LIVE Telev

5 DSF

6 HSE24

7 SAT.1

8 N24

9 TELE 5

B: Favorites

1 Sat 1

Select and mark

Back

A/B A<->B

Delete

Exit

Move

Exit

Editing the list of favourite stations

You can change the order of preset stations as required and delete stations you do not need.

You can select your favourite stations and save them in the list of favourites.

1 In the main menu, select »Channel lists« with » P+ « or » P« and press » OK « to confirm.

2 Select »Favorites« with » P+ « or » P« and press » OK « to confirm.

– The »Edit Favorites« page appears.

3 Press » P« or » P+ « to select the station to move and press




5

»

ǷǷ

« to confirm.

A/B « and then press » OK « or

– You can switch between the station list and your favourites by pressing » A/B «.

– You can store up to 100 stations in the favourites list.

– You can change the order of the stations or delete ones you do not need (see the section on editing the station list).

Note:

If you delete a station from the station list, it is also deleted from your favourites.


Note:

If the favorite channels number is over 100, no more can be add to the Favorites list. You need to delete some of the channels.

15

16

SETTINGS _________________________________________________

Installation

Menu language

Channel search

Video output

Time

Antenna connection

Special functions

Info

Select and open

Back

Time

Current time

Time Zone

Daylight saving time

Select and open

Back

08:05 h

+1.00 h

On

Exit

Exit

Setting the local time

To ensure that the TV guide always shows the current programmes at the right time, you must enter the difference between your local time and GMT (Greenwich Mean Time at longitude “0”).

All times given by the TV guide are then converted to your local time.

With clock changes (e.g. daylight saving time), you need to correct the time difference.

1 In the main menu, select »Installation« with » P« or » P+ « and press » OK « to confirm.

2 Select »Time« with » P« or » P+ « and press » OK « to confirm.

3 Select »Time Zone« with » OK « and then use » P« or » P+ « to enter the time difference in 30 minute increments.

Note:

The »Current time« item is for information only and cannot be selected.

4 Select »Daylight saving time« with » P« or » P+ « and press


5 Press » P« or » P+ « to select »Off« (winter time) or »On«

(summer time).

6 Press » OK « to confirm the setting.


SETTINGS _________________________________________________

Installation

Menu language

Channel search

Video output

Time

Antenna connection

Special functions

Info

Select and open

Back

Video output

Signal type

TV format

Picture conversion

OSD Transparency

RGB

4:3

Letterbox

❙

■■❙

■

Select and open

Back

Video output

Signal type

TV format

OSD Transparency

RGB

4:3

16:9

16:9

❙

■■❙

Select and confirm

Back

Exit

Exit

Adjusting the digital receiver to the television set

❙

❙

Specifying the video signal at the Euro AV (TV) output

You can choose between the settings »CVBS« (normal picture quality), »RGB« (high picture quality) »Y/C« (S-Video signal) and

»YUV« (component signal). The default setting is »RGB«.


2 Select »Video output« with » P« or » P+ « and press » OK « to confirm.

3 Select »Signal type« by pressing » OK «.

4 Press » P« or » P+ « to select the setting and press » OK « to confirm.


Selecting the television picture format

If you have a 4:3 format television or flat screen, select the »4:3« setting.

If you have a 16:9 format television or flat screen, select the »16:9« setting.



3 Select »TV format« by pressing » P« or » P+ « and press » OK « to confirm.

4 Press » P« or » P+ « to select the picture format and press


Note:

If picture format 4:3 is selected, you can also select picture conversion.


17

18

Video output

Signal type

TV format

Picture conversion

OSD Transparency

RGB

4:3

Letterbox

Pan&Scan

❙

■■❙

❙

Select and confirm

Back

Video output

Signal type

TV format

OSD Transparency

RGB

16:9

❙

■■❙

Modify and confirm

Back

❙

SETTINGS _________________________________________________

Selecting the television picture conversion

If you have a 4:3 format television or flat screen, the following settings are available:

»Pan&Scan« for wide-screen playback without black bars on the top and bottom edges of the screen.

»Letterbox« for wide-screen playback with black bars on the top and bottom edges of the screen.



3 Select »Picture conversion« with » P« or » P+ « and then press

» OK «.

4 Press » P« or » P+ « to select the conversion and press » OK « to confirm.


Selecting the transparency of the OSD

You can adjust the transparency of the OSD menu.



3 Select »OSD Transparency« with » P« or » P+ « and then press

» OK «.

4 Press » P« or » P+ « to select the transparency and press » OK « to confirm.


SETTINGS _________________________________________________

Installation

Menu language

Channel search

Video output

Time

Antenna connection

Special functions

Info

Select and open

Back

Antenna connection

LNB

LNB supply

Low band

High band

DiSEqC

Tone burst

A

A

1 Astra 19.2

On

9.750 GHz

10.600 GHz

Select and open

Back

Exit

Exit

Adjusting the digital receiver to the

LNB configuration of the satellite antenna

The digital receiver has been factory set so that it is ready for operation, without time-consuming adjustment, with most satellite antennas and LNB configurations.

Changes in this menu have a direct effect on the reception characteristics of the digital receiver and should therefore only be made by an expert.


2 Select »Antenna connection« with » P« or » P+ « and press


3 Select the item with » P« or » P+ « and press »

» 1 ... 0 « to make the setting:

Ǹ

«, »

Ƿ

« or

– »LNB«:

– »LNB supply«:

– »Low band«:

– »High band«:

For selecting the satellites.

For switching the LNB power supply on and off.

To set the oscillator frequency for the

Low band, select this item and press

» OK « to confirm. Enter the required value using » 1 ... 0 «.

To set the oscillator frequency for the

High band, select this item and press

» OK « to confirm. Enter the required value using » 1 ... 0 «.

– »DiSEqC«:

– »Tone burst«:

If you want to receive up to four satellites simultaneously, each LNB must be assigned to its input on the DiSEqC switch.

If you want to receive two satellites at the same time, each LNB is assigned to its input on the tone burst switch.


19

20

SETTINGS _________________________________________________

Audio settings

Audio channel

Audio output

Volume adjustment

Digital output

Select and open

Back

English

Stereo

❙

■■❙

PCM Format

Audio settings

❙

1 In the main menu, select »Settings« with » P« or » P+ « and press » OK « to confirm.

2 Select »Audio« by pressing » OK «.

– The »Audio settings« menu appears.

Note:

Further operation is explained in the following sections.

Exit

Audio settings

Audio channel

Audio output

Volume adjustment

Digital output

Select and open

Back

English

Stereo

❙

■■❙

PCM Format

Exit

❙

Changing the audio channel of the television

With stations broadcasting in several languages you can select a different language and digital sound (AC-3). The choice of audio depends on the station and the current programme.

In radio mode, you can switch to other programmes.

1 Select »Audio channel« with » P« or » P+ « and then press

» OK «.


Notes:

If you select digital sound (AC-3) for the audio channel, you can no longer select »Audio output« and »Volume adjustment«.

Digital sound (AC-3) can only be played through an external receiver or amplifier.

»Digital output« shows you the selected audio format at the digital output, and cannot be selected.

Audio settings

Audio channel

Audio output

Volume adjustment

Digital output

English

Stereo

Deutsch

❙

■■❙

Mono (Right)

PCM Format

❙

Sound settings

Here you can select the audio mode, such as stereo, mono (left) and mono (right).

1 Select »Audio output« by pressing » P« or » P+ « and press



Select and confirm

Back

Audio settings

Audio channel

Audio output

Volume adjustment

Digital output

English

Stereo

❙

■■❙

PCM Format

❙

Modify and confirm

Back

SETTINGS _________________________________________________

Volume adjustment

You can set the standard volume here. This is the volume of the device after switching on.

1 Select »Volume adjustment« by pressing » P« or » P+ « and press » OK « to confirm.

2 Press »

Ǹ

« or »

Ƿ

« to set the level and press » OK « to confirm.

Ending the settings

1 Press » i « and then » OK « to end the settings.

21

22

BASIC FUNCTIONS

______________________________

Switching on and off

1 Press »

Ǽ

« to switch on the digital receiver from standby mode.

2 Press »

Ǽ

« to switch the digital receiver to standby mode.

– The mode indicator lights up red.

Mode selection

You can choose between TV and radio modes.

1 Press »

TV

« or »

Radio

« to select the mode.

Note:

You can also change modes by selecting »Program information« in the main menu.

Selecting preset channels

1 Move up and down the channels by pressing » P+ « or » P« as required.

2 To run through the channels, press and hold down » P+ « or

» P«.

3 Enter single-digit or multi-digit preset channel numbers by pressing » 1 ... 0 « on the remote control.

– Channels with no stations assigned are ignored.

Note:

Every time you switch stations, the current channel number, the name of the station, the time, and the titles, start and finish times of the current and following programmes are shown on the screen If there is another language or digital audio effects for the current programme, you will also see this information. In the »Sound« menu, you can choose the language or the digital audio effects. Open the »Sound« menu by pressing » F «.

Adjusting the volume

You cannot change the volume in menu mode.

1 Adjust the volume by pressing »

Ǹ

« or »

Ƿ

«.

– A volume scale is shown on the television screen.

Note:

Volume changes adjust the audio signals at the » TV «, » VCR « and » AUDIO OUT « sockets on the digital receiver.

BASIC FUNCTIONS ______________________________________

Muting the sound

1 Press » d

« on the remote control to mute the sound.

2 Press » d « on the remote control to switch the sound on again.

– You can hear the sound at the volume previously set.

Selecting stations from lists

You can select stations from various lists (e.g. TV stations, favourites).

1 Press » OK « to open the station list.

– The most recently activated station list appears.

2 To change the station list, press » ?

« and press » P« or » P+ « to select the list you want.

3 Press »

Ǹ

« or »

Ƿ

« to scroll through the lists.

4 Press » P« or » P+ « to select the station and press » OK « to call it up.

5 Press » i « to quit the station list.

Switching from the current station to the previous one

The digital receiver remembers the station which was last selected, provided it was selected for at least one second.

1 Press » z « to switch from the current station to the previous one.

2 Press » z « to switch back to the current station.

Note:

You can only switch over when no menu is shown on the screen.

23

24

BASIC FUNCTIONS ______________________________________

TV Guide

Monday, 11.07.2005

9:15 - 9:30 Börse&Wirtschaft

9:30 - 10:00 N24 Wissen

10:00 - 10:18 N24 Nachrichten

10:18 - 10:34 N24 Nachrichten Wirtschaft

10:34 - 11:00 Doku: Raketen


11:31 - 12:00 Doku: Raketen


12:20 - 12:39 N24 Nachrichten Wirtschaft

12:39 - 13:00 Doku: Von der Macht verführt

Select and open

Back

Timer

Exit

TV guide

The TV guide provides information on the current station such as the title and descriptions of the current and next programmes.

1 Press » TV-G « to view the station information.

– All today’s programmes are shown.

Note:

The TV guide can also be found under »Program information« in the main menu.

2 Press » P«, » P+ «, »

Ǹ

« or »

Ƿ

« to select the programmes.

3 Press » OK « to see the information on the selected programme.

4 Press » z « to return to today’s programmes.

5 Press »

Ȅ

« to add the selected programme to the recording timer.

– The »Record timer« menu appears.

(See the section on the recording timer on page 30).

6 Press » i « to quit the TV guide.

Subtitles

Subtitles

Subtitle Language

Off

On

Deutsch

Select and confirm

Ȅ

Back

Subtitles

Subtitles

Subtitle Language

On

English

Select and open

Back Exit

Subtitles

You can show or hide the subtitles. If subtitles are available in several languages, you can select the language.

Showing subtitles

1 In the main menu, select »Settings« with » P« or » P+ « and press » OK « to confirm.

2 Select »Subtitles« with » P« or » P+ « and press » OK « to confirm.

– The »Subtitles« menu appears.

3 Select »Subtitles« with » P« or » P+ « and press » OK « to confirm.

4 Press » P« or » P+ « to show or hide the subtitles and then press


Selecting the subtitle language

1 Select »Subtitle Language« with » P« or » P+ « and press



3 Press » i « to finish the setting.

TELETEXT MODE

___________________________________

Teletext

Teletext is a service offered by some broadcasters which is provided along with the video and audio signals, is converted by the digital receiver and can be displayed on the TV screen.

1 Select the television station whose teletext pages you want to see.

2 Press » TXT « to call up teletext.

– After a short time, teletext page 100 appears on the television screen.

3 Select the teletext page with » 1 … 0 « or one of the coloured buttons.

4 Press » P« to scroll back a page.

5 Press » P+ « to scroll to the next page.

6 Press » TXT « to activate mix mode.

– The teletext is superimposed on the television picture.

7 To switch off teletext, press » TXT « again.

Additional functions

Page hold

A multiple page may contain several sub-pages, which are automatically scrolled by the broadcasting station.

1 Press » OK « to show symbols and » z « (red) to hold the page.

2 Press » z « (red) to quit the function.

Reveal answer

Certain teletext pages contain hidden answers or information. These can be viewed.

1 Press » OK « to show symbols and »

Ȅ

« (green) to show information.

2 Press »

Ȅ

« (green) to conceal the information.

Increasing the character height

If you have difficulty reading the text on the screen, you can double the character height.

1 Press » OK « to show symbols and »

ǷǷ

« (yellow) repeatedly.

25

26

TELETEXT MODE __________________________________________

Opening the main page

1 Press » OK « to show symbols and » F page (page 100).

« (blue) to show the main

Opening a sub-page directly

If the selected teletext page contains additional pages, the number of the current sub-page and the total number of pages are displayed.

2 Press »

Ǹ

« to scroll back a page.

3 Press »

Ƿ

« to scroll to the next page.

ADDITIONAL FUNCTIONS

_________________

Menu language

Language

Select and confirm

Back

Deutsch

English

Français

Italiano

Español

Suomi

Svenska

Setting the menu language

1 Press » i « to open the main menu.

2 Select »Installation« with » P« or » P+ « and press » OK « to confirm.

3 Select »Menu language« with » P« or » P+ « and press » OK « to confirm.

4 Select the »Language« setting with » OK «.



Special functions

Software update

Delete lists

Factory reset

Remote control

Select and confirm

Back

Nein

Favorites

Channel lists

Deleting stations automatically

You can delete stations from the station list and favourites list automatically.


2 Select »Special functions« with » P« or » P+ « and press » OK « to confirm.

3 Select »Delete lists« with » P«« or » P+ « and press » OK « to confirm.

4 Press » P« or » P+ « to select the list to delete and press » OK « to confirm.

– The message »Execute?« appears.

5 Press »

Ǹ

« or »

Ƿ

« to select »Yes« or »No«.

– If you select »Yes« for the station list, the station list and the favourites are deleted, and the »Station search« menu appears

(see page 28).


27

28

ADDITIONAL FUNCTIONS _____________________________

Preset satellite stations

This digital receiver has been programmed at the factory with most digital TV and radio stations on the Astra 19.2° East, EutelSat/

Hotbird 13° East, Turksat 1C, Sirius 2/3, Amos and Hellas Sat 2 satellites.

You can see which stations have been preset by pressing » OK « to call up the TV list for TV or radio.

New satellite stations are always going on air and the satellite data is constantly changed. Therefore it is advisable to occasionally start an automatic search on the digital receiver.

Installation

Menu language

Channel search

Video output

Time

Antenna connection

Special functions

Info

Select and open

Back

Automatic search

Satellite

Encrypted

Astra 19.2

No

Exit

Automatic station search

During the automatic search, the system searches the transponders in the list of stored stations for new channels.


2 Select »Channel search« with » P« or » P+ « and press » OK « to confirm.

3 Select »Automatic search« with » P« or » P+ « and press » OK « to confirm.

4 Select »Satellite« with » P« or » P+ « and press » OK « to confirm.

5 Press » P« or » P+ « to set the satellite and press » OK « to confirm.

6 Select »Encrypted« with » P« or » P+ « and press » OK « to confirm.

Level:88

S/N:13

Select and open

■■■■■■■■■■■■■■■■■■■■■■■■

■■■■■■■

Reception: ■

BER:0

Back

Ȅ

Start

Exit

7 Use » P« or » P+ « to select »Yes« (also search for encrypted stations) or »No«.

8 Press »

Ȅ

« to start the search.

– The progress of the search is shown in the transponder info line (for example »TP 10/41« means: 10 transponders of 41 completed).

– The search is complete when the »Status« line contains the message »Finished«.

– At the end of the search, new TV or radio stations are automatically added to the end of the station list.



Channel search

Automatic search

Manual search

Select and open

Back Exit

Manuell search

Satellite

Encrypted

Frequency

Polarisation

Symbol rate

Level:70

S/N:0.00

Select and open

■■■■■■

■■■■

Back

Ȅ

Start

Astra 19.2

No

12.480GHz

Horizontal

27.500Msym/s

Reception: ■

BER:>9000

Exit

Manual station search

If the station search does not find a particular station, you can look for it using the manual search. Make sure you enter all the parameters of the station you are looking for correctly. You can find the latest transponder information on the teletext pages of various broadcasters, in a current satellite TV magazine or on the internet.


2 Select »Channel search« with » P« or » P+ « and press » OK « to confirm.

3 Select »Manual search« with » P« or » P+ « and press » OK « to confirm.

4 Press » P« or » P+ « to select the item and press » OK « to confirm. Press » P« or » P+ « to make the setting and press

» OK « to confirm:

– »Satellite«: For selecting the satellite.

– »Encrypted«: Select »Yes« (also search for encrypted stations) or »No«.

– »Frequency«: Press » 1 ... 0 « to enter the five-digit frequency of the channel.

– »Polarisation«: For setting the channel polarisation (»horizontal« or »vertical«).

– »Symbol rate«: Use » 1 ... 0 « to enter the five-digit symbol

5 Press » rate of the channel.

Ȅ

« to start the search.

– At the end of the search, new TV or radio stations are automatically added to the end of the station list.

Note:

If you do not find the station you are looking for, slightly change the frequency (± 5 MHz) and start the search again.

A search will only be successful if the bit error rate (BER) is close to 0 and the reception indicator is green.


29

30


Timer

Sleep timer

Record timer

Select and open

Sleep Timer

Switch–off time

Status

Modify and confirm

Back Exit

Off

00:00 h

Back 0 _ 9 Input

Timer functions

You can set your digital receiver to switch off at a selected time or to program a recording on a connected video recorder. A total of

10 recording timers are available.

Entering the switch-off time

1 In the main menu, select »Timer« with » P« or » P+ « and press


2 Select »Sleep timer« with » P« or » P+ « and press » OK « to confirm.

3 Select »Switch-off time« with » OK «.

4 Use » 0 « – » 9 « to enter the switch-off time.

5 Press » OK « to confirm the switch-off time.

6 Select »Status« with » P« or » P+ « and press » OK « to confirm.

7 Press » P« or » P+ « to select »On« (switch-off timer activated) or »Off« (switch-off timer deactivated) and press » OK « to confirm.


– The digital receiver automatically switches to standby mode at the set time.

Record timer

Timer No. (1...10)

Start Time

Date

Duration

Stop time

Channel

Status

Select and open

Back

1

13:33 h

11/07/2005

090 Minutes

15:03 h

2. ProSieben

Aus

Exit

TV Channels

1 Sat 1

2 ProSieben

3 KABEL1

4 NEUN LIVE Telev

5 DSF

6 HSE24

7 SAT.1

8 N24

9 TELE 5

10

Select and confirm

Astra 19.2

Back

List

Exit


Programming the recording timer

1 In the main menu, select »Timer« with » P« or » P+ « and press


2 Select »Record timer« with » P« or » P+ « and press » OK « to confirm.

3 Select »Timer No. (1...10)« with » P« or » P+ « and press


4 Press » P« or » P+ « to select the timer position and press » OK « to confirm.

5 Select »Start Time«, »Date« or »Duration« with

» P« or » P+ « and press » OK « to confirm.

6 Use » 0 « – » 9 « to enter the time and day in two digits.

7 Press » OK « to confirm the entry.

8 Select »Channel« with » P« or » P+ « and press » OK « to confirm.

9 Press » P« or » P+ « to select the station from the list and press


10 Select »Status« with » P« or » P+ « and press » OK « to confirm.

11 Press » P« or » P+ « to select »On« (timer activated) or »Off«

(timer deactivated) and press » OK « to confirm.


– The digital receiver switches to the selected station at the set time.

Notes:

Your video recorder must also be programmed accordingly.

Do not switch off the digital receiver with the power switch.

If the receiver is in standby mode before the timer starts, it switches back to standby when the timer has finished.

31

32

SPECIAL SETTINGS

______________________________

Special functions

Software Update

Delete lists

Factory Reset

Remote control

Restore

Stop

Receiver 1

Select and confirm

Back

Resetting the digital receiver to its original state

This function enables you to delete the station lists and all custom settings.



3 Select »Factory Reset« with » P« or » P+ « and press » OK « to confirm.

4 Press » P« or » P+ « to select »Restore« and press » OK « to confirm.

5 Press »

Ǹ

« or »

Ƿ

« to select »Yes« and press » OK « to confirm.

– All custom settings and station lists are deleted.

– The »Menu language« menu appears.

6 Reprogram the device as described on page 13.

Special functions

Software Update

Delete lists

Factory Reset

Remote control

Select and open

Receiver 1

Back

Software Update

Searching for new software, please wait ...

Current software

Update software

1510-0100

Exit

Updating the digital receiver software

The receiver’s digital technology enables you to update the operating software.



3 Select »Software Update« by pressing » OK «.

– The digital receiver automatically starts the search for its download channel and then checks whether new data is available. This can take several minutes. Please wait until the search is finished.

4 Press » P« or » P+ « to select whether to update the data (»Yes« or »No«) and press » OK « to confirm.

– If you select »Yes« the software download begins.

– After finishing the download, the receiver restarts and automatically switches to preset station 1.

Back

Note:

An interruption during the downloading process (for example by pulling out the mains plug) can damage the operating software of the digital receiver.

Read the instructions in the menus carefully.

SPECIAL SETTINGS

______________________________

Special functions

Software Update

Delete lists

Factory Reset

Remote control

Select and confirm

Back

Receiver 1

Empfänger 1

Receiver 2

Selecting the remote control level

If you are operating two digital receivers with a the TP 766 S remote control, you must enter a separate remote control level for each digital receiver.



3 Select »Remote control« with » P« or » P+ « and press » OK « to confirm.

4 Press » P« or » P+ « to select the remote control level

»Receiver 1« or »Receiver 2« and press » OK « to confirm.

– If you now want to use the digital receiver with remote control level »Receiver 2«, you must first press and hold down » DR « while pressing the button on the remote control with the required function.


33

34

INFORMATION

_____________________________________

Reception parameters

7 SAT.1

Frequency:

Symbol rate:

Polarisation:

Bit error Rate:

Reception:

S/N:

Level:

13

254

12480 MHz

27500 Ksym/s

Vertikal

0

Ok

■■■■■■■■

■■■■■■■■■■■■■■■■■■■■■■■■

Select

Channel

Back Exit

Displaying station reception properties


2 Select »Info« with » P« or » P+ « and press » OK « to confirm.

3 Select »Reception parameters« with » P« or » P+ « and press


– The »Reception parameters« menu appears.

4 In the »Reception parameters« menu, press » P« or » P+ « to change stations.

Notes:

The lower section of the menu shows the signal properties. The lower the number of »Bit error Rate« displayed (the optimum value is »0«), and the further the »Level« bar extends to the right, the better the reception signal.

The signal level not only depends on the settings of your receiver unit, but also on the channel which is currently active.

Remember this when aligning your antenna using the signal level display.

5 Press » i « to quit the menu.

System information

DSR 1510

Manufacturer

Hardware

GRUNDIG

V. 0400

Software V. 0201

Remote control TP 766S

Receiver #1

Internet http://www.grundig.com

Back Exit

Displaying device information


2 Select »Info« with » P« or » P+ « and press » OK « to confirm.

3 Select »System information« with » P« or » P+ « and press


– It contains information on the product designation, the hardware version and the software version.

4 Press » i « to quit the menu.

Connecting the digital receiver to a PC

The » RS 232 « serial interface allows you to connect to a PC.

To do this, you need a serial cable with a 1:1 assignment, i.e. all the pins are directly connected. Depending on the PC, the cable needs either a 9- or a 15-pin D-SUB socket, and a 9-pin D-SUB plug for connection to the receiver.

You can use this connection for software updates and for uploading and downloading other data.

You can find more information on the internet at www.grundig.com.

INFORMATION ___________________________________________

Technical data

This product fulfils the European directives 89/336/EEC,

73/23/EEC and 93/68/EEC.

This device conforms to the safety regulation DIN EN 60065 and therefore the international safety regulation IEC 60065.

TV/radio stations:

Number of satellites:

Reception range:

Input symbol rate:

SAT IF input:

LNB supply:

LNB switching signal:

DiSEqC:

OSD:

Search:

Last station memory:

Teletext, VPS:

Software download:

Mains supply:

Power consumption:

Ambient temperature:

Dimensions:

Weight:

4000 in total

30

950 – 2150 MHz

2-45 megasymbols per second

1 F connector

14 V/18 V, max. 400 mA

0/22 kHz, 0.5 Vss tone burst

1.0 control, tone burst A, tone burst B

Display and programming functions in 8 languages

Automatic/manual

For the last station selected

Is sent if present in the received signal

Via Astra 19.2°East satellite, via RS 232 socket

230 V~, 50 Hz

In operation 12 W, in standby 6 W

+5 °C to +40 °C

W x H x D:

260 x 55 x 192 mm approx. 1.14 kg

Environmental note

This product has been made from high-quality parts and materials which can be reused and recycled.

Therefore, do not throw the product away with normal household waste at the end of its life. Take it to a collection point for recycling electrical and electronic devices. This is indicated by this symbol on the product, in the operating manual and on the packaging.

Please find out about collection points operated by your local authority.

Help protect the environment by recycling used products.

35

36

INFORMATION ___________________________________________

Troubleshooting

If a fault occurs, first refer to this information before you take the digital receiver for repair.

If you are unable to rectify the fault using the information given here, contact your local dealer or service specialist.

Under no circumstances should you attempt to repair the digital receiver yourself, as this will invalidate the guarantee.

PROBLEM POSSIBLE CAUSE REMEDY

No function, mode indicator not lit

Message: »Short circuit or overload at the antenna input«

No picture

No sound

Message »Faulty signal«

The remote control does not work

The time is not correctly displayed

Picture interference on stations with a frequency around

12480 MHz

Power cord incorrectly connected

Short circuit on the line

Connect the power cord correctly

Check the plug, cable and

LNB

Euro-AV (Scart) cable not properly connected, incorrect settings in the

»Device connections« menu

The sound is muted, the

Euro-AV cable is incorrectly connected or the receiver volume is set to low

The satellite antenna is not correctly installed, the satellite cable is damaged, incorrect settings in the »Reception parameters« menu

No batteries are inserted, or they are low, or the remote control is not directed at the infrared sensor

Deviation from local time

The interference may be caused by DECT cordless telephones near the receiver

Connect the Euro-AV cable correctly, correct the menu settings

Switch on the sound, connect the Euro-AV cable correctly, turn up the volume

Install the satellite antenna correctly, replace the satellite cable, enter the correct menu settings

Insert the batteries correctly, put in new batteries, point the remote control at the infrared sensor

Correct the deviation

(see page 16)

Remove the DECT telephones away from the receiver and the satellite cable

Grundig Multimedia B.V.

• De Boelelaan 7 • NL-1083 HJ Amsterdam • http://www.grundig.com

05/28 72011 800 7500

No results