Zebra ET51 Product Reference Guide
広告
広告
ET51
Enterprise Tablet
Android ™11
MN-004223-01EN Rev. A
ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corporation, registered in many jurisdictions worldwide. Google, Android, Google Play and other marks are trademarks of Google LLC. All other trademarks are the property of their respective owners. ©2021 Zebra Technologies Corporation and/or its affiliates. All rights reserved.
COPYRIGHTS & TRADEMARKS: For complete copyright and trademark information, go to zebra.com/copyright .
WARRANTY: For complete warranty information, go to zebra.com/warranty .
END USER LICENSE AGREEMENT: For complete EULA information, go to zebra.com/eula .
Terms of Use
• Proprietary Statement
This manual contains proprietary information of Zebra Technologies Corporation and its subsidiaries
(“Zebra Technologies”). It is intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the express, written permission of Zebra Technologies.
• Product Improvements
Continuous improvement of products is a policy of Zebra Technologies. All specifications and designs are subject to change without notice.
• Liability Disclaimer
Zebra Technologies takes steps to ensure that its published Engineering specifications and manuals are correct; however, errors do occur. Zebra Technologies reserves the right to correct any such errors and disclaims liability resulting therefrom.
• Limitation of Liability
In no event shall Zebra Technologies or anyone else involved in the creation, production, or delivery of the accompanying product (including hardware and software) be liable for any damages whatsoever (including, without limitation, consequential damages including loss of business profits, business interruption, or loss of business information) arising out of the use of, the results of use of, or inability to use such product, even if
Zebra Technologies has been advised of the possibility of such damages. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Revision History
Changes to the original guide are listed below:
Change Date
-01EN Rev A 7/2021 Initial release.
Description
2
Table of Contents
3
Table of Contents
Entering Numbers, Symbols, and Special Characters ..................................... 39
4
Table of Contents
5
Table of Contents
Pairing Using Bluetooth Human Interface Device .................................................. 70
Pairing Using Bluetooth Human Interface Device .................................................. 72
6
Table of Contents
7
Table of Contents
Installing the Hand Strap on the Back of the Device ............................................ 130
Installing Applications Using the USB Connection ............................................... 138
Installing Applications Using the Android Debug Bridge ...................................... 138
Installing Applications Using the Wireless Android Debug Bridge........................ 139
8
Table of Contents
Downloading the System Update Package .......................................................... 141
Performing a System Update Using microSD Card.............................................. 141
Performing a System Update Using Wireless ADB .............................................. 142
Performing an Enterprise Reset From Device Settings........................................ 144
Performing an Enterprise Reset Using microSD Card ......................................... 144
Performing an Enterprise Reset Using Wireless ADB.......................................... 145
Performing a Factory Reset Using microSD Card................................................ 147
Performing a Factory Reset Using Wireless ADB ................................................ 148
Formatting a microSD Card as Internal Memory............................................ 151
9
Table of Contents
Rugged Communication and Charging Cradle..................................................... 164
10
About This Guide
This guide provides information about setting up and using the ET51 tables with the Android ™ 11 operating system. Some screens shown in this guide may differ from the actual screens shown on the device.
Configurations
This guide covers the following configurations:
Table 1 Configurations
ET51CE
Radios
Android 11 WLAN:
802.11a/b/g/n/ac/d/h/i/k/r
WPAN: Bluetooth
Display
8.4 in. color
Memory
4 GB RAM/
32 GB Flash
ET51CE with
Integrated
Scanner
Android 11 WLAN:
802.11a/b/g/n/ac/d/h/i/k/r
WPAN: Bluetooth
8.4 in. color
ET51CT Android 11 WLAN:
802.11a/b/g/n/ac/d/h/i/k/r
WPAN: Bluetooth
10.1” color
4 GB RAM/
32 GB Flash
4 GB RAM/
32 GB Flash
Data Capture
Camera, SE4750
Expansion Back,
Ring Scanners.
Bluetooth
Scanners, and USB
Scanners.
Camera, integrated scanner, Ring
Scanners.
Bluetooth
Scanners, and USB
Scanners.
Camera, SE4750
Expansion Back,
Ring Scanners.
Bluetooth
Scanners, and USB
Scanners.
Related Documents and Software
The following documents provide more information about the tablet.
• ET51/56 Enterprise Tablet Quick Reference Guide, p/n MN-003332-xx
• ET51 Enterprise Tablet with Integrated Scanner Quick Reference Guide, p/n MN-003777-xx.
For the latest version of this guide and all guides, go to: zebra.com/support .
11
About This Guide
Notational Conventions
Notational conventions are used to highlight important information.
• Bold text is used to highlight the following:
• Dialog box, window and screen names
• Drop-down list and list box names
• Check box and radio button names
• Icons on a screen
• Key names on a keypad
• Button names on a screen
• Bullets (•) indicate:
• Action items
• Lists of alternatives
• Lists of required steps that are not necessarily sequential.
• Sequential lists (for example, those that describe step-by-step procedures) appear as numbered lists.
Icon Conventions
The following icons are used throughout the document. The icons and their associated meanings are described below.
NOTE: The text here indicates information that is supplemental for the user to know and that is not required to complete a task.
IMPORTANT: The text here indicates information that is important for the user to know.
CAUTION: If the precaution is not heeded, the user could receive minor or moderate injury.
WARNING: If danger is not avoided, the user CAN be seriously injured or killed.
DANGER: If danger is not avoided, the user WILL be seriously injured or killed.
Service Information
If you have a problem with your equipment, contact Customer Support for your region. Contact information is available at: zebra.com/support .
When contacting support, please have the following information available:
• Serial number of the unit (found on manufacturing label)
• Model number or product name (found on manufacturing label)
• Software type and version number
12
About This Guide
Customer Support responds to calls by email or telephone within the time limits set forth in support agreements.
If the problem cannot be solved by Customer Support, the user may need to return the equipment for servicing and will be given specific directions. We are not responsible for any damages incurred during shipment if the approved shipping container is not used. Shipping the units improperly can possibly void the warranty. If applicable, remove the microSD card from the device before shipping for service.
If the device was purchased from a business partner, contact that business partner for support.
Determining Software Versions
Before contacting Customer Support, determine the current software version on your device.
1.
Swipe down from the Status bar with two fingers to open the Quick Access panel, and then touch .
2.
Touch About phone .
3.
Scroll to view the following information:
• Battery information
• SW components
• Legal information
• Model & hardware
• Android version
• Android security patch level
• Android security patch version
• Baseband version
• Kernel version
• Build number
Determining the Serial Number
Before contacting Customer Support, determine the serial number of your device.
1.
Swipe down from the Status bar with two fingers to open the Quick Access panel, and then touch .
2.
Touch About phone > Model & hardware > Serial number.
13
Getting Started
Introduction
This chapter explains how to set the device up for the first time.
Unpacking
Carefully remove all protective material from around the tablet and save the shipping container for later storage and shipping.
Verify that you received all equipment listed below:
• Tablet with lithium-ion battery
• Quick Reference Guide
• Additional hand strap screws (ET51 Enterprise Tablet with integrated Scanner only).
• Cradle caps (ET51 Enterprise Tablet with integrated Scanner only).
Inspect the equipment for damage. If you are missing any equipment or if you find any damaged equipment, contact the Zebra Support Center immediately. See Service Information on page 12 for contact information.
14
Getting Started
ET51 Features
Figure 1 ET51 Front View
1
2
3
4
5
2 1
2 3 4
2
5
10.1 in. version
8.4 in. version
Table 2 ET51 Front View
Item
1
2
3
4
5
Ambient Light Sensor - Recognizes the ambient light and adjusts the display brightness
(if enabled).
Description
Dual Front-Facing Microphones - Use for voice communications for audio recordings.
Front Facing Camera - Use for video conferencing or capturing images and video.
Notification LED - Lights blue when an application sends a notification.
Charging Indicator LED - Indicates charging status.
• Off - device is not connected to charger.
• Blinking Orange - device is charging.
• Green - device is connected and fully charged.
• Red - charge error.
15
Figure 2 ET51 Back View
Getting Started
11
6
7 10
8
9
6
7
8
Table 3 ET51 Back View
Item
9
10
11
Description
Rear Camera - Auto-focus camera for capturing high resolution images and video.
Camera LED Flash - Provides illumination for the camera.
Power Button - Push once to start the device; push it again to enable sleep mode. Push and hold it to shut down the tablet.
Volume Key - Push the left side to reduce the volume. Press the right side to increase the volume.
USB-C / Display - Provides communications with a host computer using a USB-C cable or a video monitor using a third-party adapter.
Battery Cover - Covers the replaceable battery.
16
Getting Started
Figure 3 ET51 Bottom View
8.4 in. Version
13
12
16 15
14
13 10.1 in. Version
17
15
16
14
13
Table 4 Bottom View
Item
12
13
14
15
16
17
Description
NFC Antenna Position - Use to read NFC cards.
Stereo Speakers - Provides audio playback.
Alignment Holes - Use to align tablet with cradle
Latching Slots - Insertion point for Communication and Charging cradle locks.
Charging Pins - Contact point for cradle charging.
Docking Connector - Interfaces with the cradle.
ET51 with Integrated Scanner Features
Figure 4 ET51 with Integrated Scanner Front View
1
2
3
4 5
6
7
8
9
10
17
Getting Started
Table 5 ET51 with Integrated Scanner Front View
Item
1
2
3
4
5
6
7
8
9
10
Adjustable Hand Strap - Use to securely hold the device in your hand.
(if enabled).
Description
Exit Window - Provides data capture using the imager.
Ambient Light Sensor - Recognizes the ambient light and adjusts the display brightness
Dual Front-Facing Microphones - Use for voice communications for audio recordings.
Front Facing Camera - Use for video conferencing or capturing images and video.
Power Button - Push once to start the device; push it again to enable sleep mode. Push and hold it to shut down the device.
Volume Key - Press the left side to reduce the volume. Press the right side to increase the volume.
USB-C Port - Use to charge the device using a USB-C cable and power supply.
Charging Indicator LED - Indicates charging status.
• OFF - device is not connected to charger.
• Blinking ORANGE - device is charging.
• GREEN - device is connected and fully charged.
• RED - charge error.
Notification LED - Lights blue when an application sends a notification.
Figure 5 ET51 with Integrated Scanner Back View
12
13
11
14
15
13
16
17
16
18
Getting Started
Table 6 ET51 with Integrator Scanner Back View
14
15
16
17
Item
11
12
13
Description
Back Cover - Covers the replaceable battery.
NFC Antenna Position - Use to read NFC cards.
Scan Button - Initiates barcode data capture when a scan-enabled application is active.
Rear Camera - Use for high resolution images and video.
Camera LED Flash - Provides illumination for the camera.
Stereo Speakers - Provides audio playback.
Docking Connector - Interfaces with the cradle.
Getting Started
In order to start using the device for the first time:
• Install microSD card
• Charge the device
• Perform basic configuration.
Installing a microSD Card
To install a microSD card:
1.
Press and hold the Power button until the menu appears.
2.
3.
Touch Power off .
Lift the notched corner of the battery cover and carefully lift the battery cover off the device.
4.
On the 8.4 in. version, push the two locking tabs up, then pull up on the tab to remove battery.
On the 10.1 in. version, push the two locking tabs up (1), then lift the battery up (2).
19
Getting Started
Figure 6 Removing the Battery - 8.4 in.
1
1
2
Locking tabs
Pull tabs
Figure 7 Removing the Battery - 10.1 in.
2
Install the microSD Card
1.
Insert the microSD card with contacts facing down; 8.4 in. version shown here.
20
Figure 8 Inserting microSD Card
Getting Started
8.4 in. Version 10.1 in. Version
2.
Push the micro SD card in and ensure that it locks into place.
21
Getting Started
Charging the Battery
Use one of the cradles to charge the main battery installed in the device. See the
accessories.
The 8.4 in. tablet main battery charges from fully depleted to 90% in approximately 2.5 hours and from fully depleted to 100% in approximately 3.5 hours.
The 10.1 in. tablet main battery charges from fully depleted to 90% in approximately three hours and from fully depleted to 100% in approximately four hours.
NOTE: The Charging indicator only illuminates when the tablet is connected to AC power.
Google Account Setup
NOTE: The device has to be connected to the internet in order to set up a Google ™ account.
A Google account is only required on devices with GMS software.
The first time the device starts, the Setup Wizard displays. Follow the on-screen instructions to set up a
Google account, configure Google Pay ™ for purchasing items from the Google Play ™ store, to enter your personal information, and enable backup/restore features.
Turning Off the Tablet
NOTE: After the device is powered off and external power is applied to the device, the device will automatically power on. This includes powered cradles, Expansion Back with Power Pack, Rugged
Charge Connector, and power supply/USB-C cable.
To turn off the device:
1.
Press and hold the power button until the menu appears.
2.
Touch Power off .
Replacing the microSD Card
CAUTION: To avoid damage to the microSD card slot, do not pull the microSD card out of the microSD
Card slot. Push the microSD card in to eject it.
To replace the microSD card:
1.
Press and hold the Power button until the menu appears.
2.
3.
Touch Power off .
Lift the notched corner of the battery cover and carefully lift the battery cover off the device.
4.
On the 8.4 in. version, push the two locking tabs up, then pull up on the tab to remove battery.
On the 10.1 in. version, push the two locking tabs up, then lift the battery up.
5.
6.
7.
8.
Push in the SIM card and release. The card eject slightly.
Remove the microSD card from the card slot. The card should easily slide out. If not, the microSD card was not ejected correctly. Repeat step 5.
Insert the replacement microSD card with contacts facing down.
Push the microSD card in and ensure that it locks into place.
22
Getting Started
9.
Replace the battery.
10.
Press the battery down to ensure the two battery latches engage.
11.
Replace the battery cover.
Interactive Sensor Technology
The device contains sensors that monitor movement, orientation and ambient light:
• Gyroscope - Measures angular rotational velocity to detect rotation of the device.
• Accelerometer - Measures the linear acceleration of movement to detect the orientation of the device.
• Digital Compass - The digital compass or magnetometer provides simple orientation in relation to the
Earth's magnetic field. As a result, the device always knows which way is North so it can auto rotate digital maps depending on the physical orientation of the device.
• Light Sensor - Detects ambient light and adjusts the screen brightness.
In order to take advantage of these sensors, applications use API commands. Refer to the Zebra Android
EMDK for more information.
Turning Off the Display
To turn off the display press and release the power button.
23
Using the Device
Home Screen
Turn on the device to display the Home screen. Depending on how your system administrator configured your device, your Home screen may appear differently than the graphics in this section.
After a suspend or screen time-out, the Home screen displays with the lock slider. Touch the screen and slide up to unlock.
The Home screen provides four additional screens to place widgets and shortcuts. Swipe the screen left or right to view the additional screens.
NOTE: By default, AOSP devices do not have the same icons on the Home screen as GMS devices. Icons are shown below for example only.
Home screen icons can be configured by the user and may look different than shown.
Figure 9 Home Screen
24
Using the Device
1
4
5
2
3
6
7
Status Bar
Widgets
Shortcut Icons
Folder
Back
Home
Recent
Displays the time, status icons (right side), and notification icons (left side).
For more information see Notification Icons on page 26 and
.
Launches stand-alone apps that run on the Home screen.
Opens apps installed on the device.
Contains apps.
Displays the previous screen.
Displays the Home screen.
Displays recently used applications.
Setting Home Screen Rotation
By default, the Home screen rotation is disabled.
1.
Touch and hold anywhere on the Home screen until the options appear.
2.
3.
4.
5.
Touch Home settings .
Touch the Allow Home screen rotation switch.
Touch the Home button.
Rotate the device.
Status Bar
The Status bar displays the time, notification icons (left side), and status icons (right side).
If there are more notifications than can fit in the Status bar, a dot displays indicating that more notifications exist. Swipe down from the Status bar to open the Notification panel and view all notifications and status.
Figure 10 Notification and Status Icons
1
2
1
Notification Icons. See Notification Icons on page 26 .
Status Icons. See
.
2
25
Using the Device
Notification Icons
Notification icons indicate app events and messages.
Table 7 Notification Icons
Icon
Main battery is low.
Description
More notifications are available for viewing.
Data is syncing.
Indicates an upcoming event. AOSP devices only.
Indicates an upcoming event. GMS devices only.
Open Wi-Fi network is available.
Audio is playing.
Problem with sign-in or sync has occurred.
Device is uploading data.
Animated: the device is downloading data. Static: the download is complete.
Device is connected to or disconnected from a virtual private network (VPN).
Preparing internal storage by checking it for errors.
USB debugging is enabled on the device.
Wired headset with a boom module is connected to the device.
Wired headset without a boom module is connected to the device.
PTT Express Voice client status. See the PTT Express PTT Notification Icons for a complete list.
Indicates the RxLogger app is running.
Indicates the Bluetooth scanner is connected to the device.
Indicates the ring scanner is connected to the device in HID mode.
26
Using the Device
Status Icons
Status icons display system information for the device.
Table 8 Status Icons
Icon
Alarm is active.
Main battery is fully charged.
Main battery is partially drained.
Description
Main battery charge is low.
Main battery charge is very low.
Main battery is charging.
All sounds, except media and alarms, are muted. Vibrate mode is active.
Do Not Disturb mode active.
Airplane Mode is active. All radios are turned off.
Bluetooth is on.
The device is connected to a Bluetooth device.
Connected to a Wi-Fi network. Indicates the Wi-Fi version number.
Not connected to a Wi-Fi network or no Wi-Fi signal.
Connected to an Ethernet network.
Speakerphone enabled.
Managing Notifications
Notification icons report the arrival of new messages, calendar events, alarms, and ongoing events. When
for a list of possible notification icons and their description.
• To view a list of all notifications, open the Notification panel by dragging the Status bar down from the top of the screen.
27
Figure 11 Notification Panel
Using the Device
Quick Settings Bar
• To respond to a notification, open the Notification panel and then touch a notification. The Notification panel closes and the corresponding app opens.
• To manage recent or frequently used notifications, open the Notification panel and then touch Manage notifications . Touch the toggle switch next to an app to turn off all notifications, or touch an app for more notification options.
• To clear all notifications, open the Notification panel and then touch CLEAR ALL . All event-based notifications are removed. Ongoing notifications remain in the list.
• To close the Notification panel, swipe the Notification panel up.
Opening the Quick Access Panel
Use the Quick Access panel to access frequently used settings (for example, Airplane mode). To get to the
Quick Access Panel:
• If the device is locked, swipe down once.
• If the device is unlocked, swipe down once with two fingers, or twice with one finger.
• If the Notification panel is open, swipe down from the Quick Settings bar.
28
Figure 12 Quick Access Panel
Using the Device
NOTE: Not all icons are pictured. Icons may vary.
Quick Access Panel Icons
• Display brightness - Use the slider to decrease or increase the brightness of the screen.
• Wi-Fi network - Turn Wi-Fi on or off. To open Wi-Fi settings, touch the Wi-Fi network name.
• Bluetooth settings - Turn Bluetooth on or off. To open Bluetooth settings, touch Bluetooth .
• Battery saver - Turn Battery saver mode on or off. When Battery saver mode is on the performance of the device is reduced to preserve battery power.
• Invert colors - Invert the display colors.
• Do not disturb - Control how and when to receive notifications.
• Airplane mode - Turn Airplane mode on or off. When Airplane mode is on the device does not connect to Wi-Fi or Bluetooth.
• Auto-rotate - Lock the device’s orientation in portrait or landscape mode or set to automatically rotate.
• Flashlight - Turn flashlight on or off. Turn camera flash on or off.
• Night Light - Tint the screen amber to make it easier to look at the screen in dim light. Set Night Light to turn on automatically from sunset to sunrise, or at other times.
• Screen Cast - Share phone content on Chromecast or a television with Chromecast built-in. Touch cast screen to display a list of devices, then touch a device to begin casting.
• Dark Theme - Toggles dark theme on and off. Dark themes reduce the luminance emitted by the screen, while meeting minimum color contrast ratios. It helps improve visual ergonomics by reducing eye strain, adjusting brightness to current lighting conditions, and facilitating screen use in dark environments, while conserving battery power.
• Focus mode - Turn on to pause distracting apps. To open Focus mode settings, touch and hold.
29
Using the Device
• Bedtime mode - Turn grayscale on and off. Grayscale turns the screen black and white, reducing phone distractions and improving battery life.
• Nearby Share - Helps find and interact with services and devices close to the device. To open Nearby
Share settings, touch and hold.
• Screen Record - Turn on to record your phone screen. Tap the toggle switches to record audio or show touches on the screen.
• NFC - Turn on to allow data sharing when the device touches another Near Field Communication
(NFC) device.
Editing Icons on the Quick Settings Bar
The first several setting tiles from the Quick Access panel become the Quick Settings bar.
Open the Quick Access panel and touch to edit, add, or remove settings tiles.
Battery Management
Observe the recommended battery optimization tips for your device.
• Set the screen to turn off after a short period of non-use.
• Reduce screen brightness.
• Turn off all wireless radios when not in use.
• Turn off automatic syncing for Email, Calendar, Contacts, and other apps.
• Minimize use of apps that keep the device from suspending, for example, music and video apps.
NOTE: Before checking the battery charge level, remove the device from any AC power source (cradle or cable).
Checking Battery Status
• Open Settings and touch About phone > Battery Information .
Or, swipe up from the bottom of the screen and touch to open the Battery Manager app. See
• Battery present status indicates if the battery is present.
• Battery level lists the battery charge (as a percentage of fully charged).
• Swipe down with two fingers from the status bar to open the quick access panel.
• Battery percentage is displayed next to the battery icon.
Monitoring Battery Usage
The Battery screen provides battery charge details and power management options to extend battery life.
1.
Go to Settings .
2.
Touch Battery .
Display battery information and power management options for a specific app.
1.
Go to Settings .
30
Using the Device
2.
3.
Touch Apps & notifications .
Touch an app.
4.
Touch Advanced > Battery .
Different apps display different information. Some apps include buttons that open screens with settings to adjust power use. Use the DISABLE or FORCE STOP buttons to turn off apps that consume too much power.
Low Battery Notification
When the battery charge level drops below 18%, the device displays a notice to connect the device to power. The user should charge the battery using one of the charging accessories.
When the battery charge drops below 10%, the device displays a notice to connect the device to power.
The user must charge the battery using one of the charging accessories.
When the battery charge drops below 4%, the device turns off. The user must charge the battery using one of the charging accessories.
Interactive Sensor Technology
The device contains sensors that monitor movement, orientation and ambient light.
• Gyroscope - Measures angular rotational velocity to detect rotation of the device.
• Accelerometer - Measures the linear acceleration of movement to detect the orientation of the device.
• Digital Compass - The digital compass or magnetometer provides simple orientation in relation to the
Earth's magnetic field. As a result, the device always knows which way is North so it can auto rotate digital maps depending on the physical orientation of the device.
• Light Sensor - Detects ambient light and adjusts the screen brightness.
In order to take advantage of these sensors, applications use API commands. Refer to the Google Android
Sensor APIs for more information. For information on the Zebra Android EMDK, go to: techdocs.zebra.com
.
Interactive Sensor Technology
The device contains sensors that monitor movement, orientation and ambient light.
• Gyroscope - Measures angular rotational velocity to detect rotation of the device.
• Accelerometer - Measures the linear acceleration of movement to detect the orientation of the device.
• Digital Compass - The digital compass or magnetometer provides simple orientation in relation to the
Earth's magnetic field. As a result, the device always knows which way is North so it can auto rotate digital maps depending on the physical orientation of the device.
• Light Sensor - Detects ambient light and adjusts the screen brightness.
In order to take advantage of these sensors, applications use API commands. Refer to the Google Android
Sensor APIs for more information. For information on the Zebra Android EMDK, go to: techdocs.zebra.com
.
31
Using the Device
Waking the Device
The device goes into Suspend mode when you press the Power button or after a period of inactivity (set in the Display settings window).
1.
To wake the device from Suspend mode, press the Power button.
The Lock screen displays.
2.
Swipe the screen up to unlock.
• If the Pattern screen unlock feature is enabled, the Pattern screen appears instead of the Lock screen.
• If the PIN or Password screen unlock feature is enabled, enter the PIN or password after unlocking the screen.
NOTE: If you enter the PIN, password, or pattern incorrectly five times, you must wait 30 seconds before trying again.
If you forget the PIN, password, or pattern contact your system administrator.
USB Communication
Connect the device to a host computer to transfer files between the device and the host computer.
When connecting the device to a host computer, follow the host computer’s instructions for connecting and disconnecting USB devices, to avoid damaging or corrupting files. For information on USB communication accessories available for this device, see
Transferring Files
Use Transfer files to copy files between the device and the host computer.
1.
Connect the device to a host computer using a USB accessory.
2.
3.
4.
5.
6.
7.
On the device, pull down the Notification panel and touch Charging this device via USB .
By default, No data transfer is selected.
Touch File Transfer .
On the host computer, open a file explorer application.
Locate the device as a portable device.
Open the Internal storage folder.
Copy files to and from the device or delete files as required.
Transferring Photos
Use PTP to copy photos from the device to the host computer.
1.
Connect the device to a host computer using a USB accessory.
2.
3.
4.
On the device, pull down the Notification panel and touch Charging this device via USB .
Touch PTP .
On the host computer, open a file explorer application.
5.
Open the Internal storage folder.
32
Using the Device
6.
Copy or delete photos as required.
Disconnect from the Host Computer
CAUTION: Carefully follow the host computer’s instructions to disconnect USB devices correctly to avoid losing information.
To disconnect the device from the host computer:
1.
On the host computer, unmount the device.
2.
Remove the device from the USB accessory.
33
Settings
Accessing Settings
There are multiple ways to access settings on a device.
• Swipe down with two fingers from the top of the Home screen to open the Quick Access panel and touch .
• Double-swipe down from the top of the Home screen to open the Quick Access panel and touch .
• Swipe up from the bottom of the Home screen to open APPS and touch Settings .
Display Settings
Use Display settings to change the screen brightness, enable night light, change the background image, enable screen rotation, set sleep time, and change font size.
Setting the Screen Brightness Manually
Manually set the screen brightness using the touchscreen.
1.
Swipe down with two fingers from the Status bar to open the Quick Access panel.
2.
Slide the icon to adjust the screen brightness level.
Setting the Screen Brightness Automatically
Automatically adjust the screen brightness using the built-in light sensor.
1.
2.
3.
4.
Go to Settings .
Touch Display .
If disabled, touch Adaptive brightness to automatically adjust the brightness.
By default, Adaptive brightness is enabled. Toggle the switch to disable.
Touch the Home button.
Setting Night Light
The Night Light setting tints the screen amber, making the screen easier to look at in low light.
1.
2.
Go to Settings .
Touch Display .
34
Settings
6.
7.
8.
3.
4.
5.
Touch Night Light .
Touch Schedule .
Select one of the schedule values:
• None (default)
• Turns on at custom time
• Turns on from sunset to sunrise .
By default, Night Light is disabled. Touch TURN ON NOW to enable.
Adjust the tint using the Intensity slider.
Touch the Home button.
Setting Screen Rotation
By default, screen rotation is enabled.
1.
2.
3.
4.
Go to Settings .
Touch Display > Advanced .
Touch Auto-rotate screen .
Touch the Home button.
Setting Screen Timeout
Set the screen sleep time.
1.
2.
3.
Go to Settings .
Touch Display > Advanced > Screen timeout .
Select one of the sleep values.
4.
• 15 seconds
• 30 seconds
• 1 minute (default)
• 2 minutes
• 5 minutes
• 10 minutes
• 30 minutes
Touch the Home button.
Lock Screen
The lock screen setting wakes the screen when notifications are received.
1.
2.
3.
4.
Go to Settings .
Touch Display > Advanced .
Touch Lock screen .
In the When to show section, enable or disable an option using the switch.
35
Settings
5.
Touch the Home button.
Setting Font Size
Set the size of the font in system apps.
1.
2.
3.
4.
Go to Settings .
Touch Display > Advanced .
Touch Font size .
Select one of the font size values.
5.
• Small
• Default
• Large
• Largest.
Touch the Home button.
Touch Panel Mode
The device display is able to detect touches using a finger, a conductive-tip stylus, or gloved finger.
NOTE: A glove can be made of medical latex, leather, cotton, or wool.
For optimal performance use a Zebra certified stylus.
1.
2.
3.
4.
Go to Settings .
Touch Display > Advanced .
Touch TouchPanelUI .
Select:
• Finger Only Mode - Moisture optimized - Rain Mode to use a finger on the screen and when the device may have water on the screen.
5.
• Stylus and Finger to use a finger or a stylus on the screen.
• Glove and Finger to use a finger or a gloved finger on the screen.
Touch the Home button.
Setting the Date and Time
You are only required to set the time zone or set the date and time if the wireless LAN does not support
Network Time Protocol (NTP)
1.
2.
3.
4.
5.
6.
7.
Go to Settings .
Touch System > Date & time .
Touch Use network-provided time to disable automatic date and time synchronization.
Touch Date .
In the calendar, set today’s date.
Touch OK .
Touch Time .
36
Settings
8.
Touch the green circle, drag to the current hour and then release.
9.
Touch the green circle, drag to the current minute and then release.
10.
Touch AM or PM .
11.
Touch OK .
12.
Touch Time zone > Time zone and select the current time zone from the list. This option may not be available in some locations.
13.
Touch Time zone > Region and select the current region from the list.
14.
Touch Update Interval to select interval to synchronize the system time from the network.
15.
In TIME FORMAT , choose either Use local default or Use 24-hour format .
16.
Touch the Home button.
General Sound Setting
Use the Sound settings to configure media and alarm volumes.
1.
Go to Settings .
2.
3.
Touch Sound .
Touch an option to set sounds.
Sound Options
• Media volume - Controls the music, games, and media volume.
• Alarm volume - Controls the alarm clock volume.
• Notification volume - Controls the notification volume (WLAN only).
• Do Not Disturb - Mutes some or all sounds and vibrations.
• Media - Enable or disable to show media controls in Quick Access Panel.
• Shortcut to prevent ringing - Select how the shortcut method prevents ringing.
• Default notification sound - Select a sound to play for all system notifications.
• Default alarm sound - Select a sound to play for alarms.
• Other sounds and vibrations
• Screen locking sounds - Play a sound when locking and unlocking the screen (default – enabled).
• Charging sounds and vibration - Plays a sound and vibrates when power is applied to the device
(default - enabled).
• Touch sounds - Play a sound when making screen selections (default – enabled).
• Touch vibration - Vibrate the device when making screen selections (default – disabled).
1.
• Touch vibration - Vibrate the device when making screen selections (default – disabled).
37
Settings
Remapping a Button
Buttons on the device can be programmed to perform different functions or as shortcuts to installed apps. For a list of key names and descriptions, refer to: techdocs.zebra.com
.
1.
2.
3.
Go to Settings .
Touch Key Programmer . A list of programmable buttons displays.
Select the button to remap.
4.
5.
Touch the Shortcut , the Keys and Buttons , or the Trigger tab that lists the available functions, applications, and triggers.
Touch a function or application shortcut to map to the button.
NOTE: If you select an application shortcut, the application icon appears next to the button on the Key
Programmer screen.
6.
Touch the Home button.
Remappable Keys
Figure 13 Key Positions
VOLUME_DOWN
VOLUME_UP
• VOLUME_DOWN - Volume down button.
• VOLUME_UP - Volume up button.
Keyboards
The device provides multiple keyboard options.
• Enterprise Keyboard
NOTE: By default the Enterprise and Virtual Keyboards are disabled.
Keyboard Configuration
Enabling Keyboards
1.
2.
Go to Settings .
Touch System > Languages & input > Virtual keyboard > Manage keyboards .
38
Settings
3.
Touch a keyboard to enable.
Switching Between Keyboards
• To switch between keyboards, touch in a text box to display the current keyboard.
• On the Gboard keyboard, touch and hold (GMS devices only).
• On the Android keyboard, touch and hold (AOSP devices only).
• On the Enterprise keyboard, touch . Only available with Mobility DNA Enterprise License. Not pre-installed on the device. Contact Zebra Support for more information.
Using the Android and Gboard Keyboards
Use the Android or Gboard keyboards to enter text in a text field.
To configure the keyboard settings, touch and hold the comma and then slide your finger to .
Edit Text
Edit entered text and use menu commands to cut, copy, and paste text within or across apps. Some apps do not support editing some or all of the text they display; others may offer their own way to select text.
Entering Numbers, Symbols, and Special Characters
1.
2.
Enter numbers and symbols.
• Touch and hold one of the top-row keys until a menu appears then select a number or special character.
• Touch the Shift key once for a single capital letter. Touch the Shift key twice to lock in uppercase. Touch the Shift key a third time to unlock Capslock.
• Touch ?123 to switch to the numbers and symbols keyboard.
• Touch the =\< key on the numbers and symbols keyboard to view additional symbols.
Enter special characters.
• Touch and hold a number or symbol key to open a menu of additional symbols. A larger version of the key displays briefly over the keyboard.
Using the Enterprise Keyboard
The Enterprise Keyboard contains multiple keyboard types.
• Numeric
• Alpha
• Special characters
• Data capture.
Numeric Tab
The numeric keyboard is labeled 123 . The keys displayed vary on the app being used. For example, an arrow displays in Contacts , however Done displays in Email account setup.
39
Settings
Alpha Tab
The alpha keyboard is labeled using the language code. For English, the alpha keyboard is labeled EN .
Additional Character Tab
The additional characters keyboard is labeled #*/ .
Touch to enter emoji icons in a text message.
Touch ABC to return to the Symbols keyboard.
Scan Tab
The Scan tab provides an easy data capture feature for scanning barcodes.
Language Usage
Use the Language & input settings to change the device’s language, including words added to the dictionary.
Changing the Language Setting
3.
4.
1.
2.
5.
6.
Go to Settings .
Touch System > Languages & input .
Touch Languages . A list of available languages displays.
If the desired language is not listed, touch Add a language and select a language from the list.
Touch and hold to the right of the desired language, then drag it to the top of the list.
The operating system text changes to the selected language.
Adding Words to the Dictionary
3.
4.
1.
2.
5.
6.
7.
Go to Settings .
Touch System > Languages & input > Advanced > Personal dictionary .
If prompted, select the language where this word or phase is stored.
Touch + to add a new word or phrase to the dictionary.
Enter the word or phrase.
In the Shortcut text box, enter a shortcut for the word or phrase.
Touch the Home button.
Notifications
Setting App Notifications
To set notification settings for a specific app:
1.
2.
Go to Settings .
Touch Apps & notifications .
40
Settings
3.
Under Recently opened apps, touch SEE ALL XX APPS . The App info screen displays.
If there are no recently opened apps, touch App info to open the App Info screen.
Select an app. Options vary depending on the app selected.
4.
5.
Select an available option:
• Open - Opens the app.
• Disable - Turn the app off and hide it. The app no longer appears in the All Apps list. You must re-enable the app to use it.
• Force Stop - Turn off the app.
• Notifications
• All app notifications - Select to turn all notifications from this app on (default) or off.
Touch a specific notification category to display additional options.
• Default - Allow notifications from this app to make sound or vibrate the device.
• Silent - Do not allow notifications from this app to make sound or vibrate.
• Minimize - In the Notification panel, collapse notifications to one line.
• Advanced - Touch for additional options.
• Allow notification dot - Do not allow this app to add a notification dot to the app icon.
• Additional settings in the app - Open the app settings.
• Permissions - Configure which permissions are allowed or denied for this app.
• Storage & cache - View the amount of storage and cache space used for this app. You can choose to
Clear Storage and Clear Cache for the app to free up storage space on the device.
• Mobile data & Wi-Fi - View the data usage for this app. You can choose to enable Background data usage or allow Unrestricted data usage by this app.
• Advanced - Touch for additional options.
• Screen time - Touch for options to set an App timer that limits the amount of time you can use this app and to Manage notifications .
• Battery - Set Background restriction and Battery optimization for this app.
• Open by default - Modify which links or files the app opens by default.
• Advanced
• Picture-in-picture - Allow this app to create a picture-in-picture window when the app is running in the background.
• Install unknown apps - Allow this app to install unknown apps.
• Display over other apps - Allow this app to display over other apps.
• Modify system settings - Allow this app to modify system settings.
• Store
• App details - Opens Google Play to display information about the app.
Viewing Notification Settings for All Apps
To view the notification settings for all apps:
1.
Go to Settings .
41
Settings
2.
3.
4.
Touch Apps & Notifications .
Scroll down to Notifications to view how many apps have notifications turned off.
To set or view notifications settings for a specific app, see Setting App Notifications on page 40 .
Controlling Lock Screen Notifications
To control whether notifications can be seen when the device is locked:
1.
2.
3.
Go to Settings .
Touch Apps & notifications > Notifications .
Touch Notifications on lockscreen and select one of the following:
• Show conversations, default, and silent (default)
• Hide silent conversations and notifications
• Don't show any notifications.
42
Applications
The APPS
screen displays icons for all installed apps. See Application Deployment for information on
installing and uninstalling apps. For information on standard Android apps, go to Google Play .
The following table describes the apps installed on the device.
NOTE: Not all apps are available on all devices.
Table 1 Apps
Icon Description
Battery Manager - Displays battery information, including charge level, status, health and wear level.
Bluetooth Pairing Utility – Use to pair a Zebra Bluetooth scanner with the device by scanning a barcode.
Camera
- Take photos or record videos. For more information, see Camera on page 48 .
DataWedge - Enables data capture using the imager. For more information, see
.
DWDemo - Provides a way to demonstrate the data capture features using the imager. For more information, see
DataWedge Demonstration on page 53 .
Email - Use to send and receive email. AOSP only.
Files - Organize and manage files on the device.
Gallery - Use to view photos stored on the microSD card. AOSP only.
License Manager - Use to manage software licenses on the device.
43
Applications
Table 1 Apps (Continued)
Icon Description
MSRN - Use to verify authenticity of the paired Snap-on MSR and to provision the Snap-on
MSR.
Phone - Use to dial a phone number when used with some Voice over IP (VoIP) clients
(VoIP telephony ready only).
PTT Express - Use to launch PTT Express client for VoIP communication.
RxLogger
- Use to diagnose device and app issues. For more information, see RxLogger on page 55 .
Settings - Use to configure the device.
StageNow - Allows the device to stage a device for initial use by initiating the deployment of settings, firmware, and software.
VC Settings
- Use to control settings for the device. See VC Settings on page 57 .
Videos - Use to view videos on the device. AOSP only.
VoD - The Video on Device basic app provides a how-to video for proper device cleaning.
For Video on Device licensing information, go to learning.zebra.com
.
Worry Free Wifi Analyzer - A diagnostic intelligent app. Use to diagnose surrounding area and display network stats, such as coverage hole detection, or AP in vicinity. Refer to the
Worry Free Wi-Fi Analyzer Administrator Guide for Android.
Zebra Bluetooth Settings - Use to configure Bluetooth logging.
Zebra Data Services - Use to enable or disable Zebra Data Services. Some options are set by the system administrator.
Accessing Apps
All apps installed on the device are accessed using the APPS window.
1.
On the Home screen, swipe up from the bottom of the screen.
2.
3.
Slide the APPS window up or down to view more app icons.
Touch an icon to open the app.
44
Applications
Switching Between Recent Apps
Use the Recent button to switch between recently used apps.
1.
Touch Recent button.
2.
A window appears on the screen with icons of recently used apps.
Slide the apps displayed up and down to view all recently used apps.
3.
4.
Swipe left or right to remove app from the list and force close the app.
Touch an icon to open an app or touch Back button to return to the current screen.
Battery Manager
The Battery Manager provides detailed information about the battery and battery swap procedures on supported devices.
Opening Battery Manager
To open the Battery Manager app, swipe up from the bottom of the Home screen, and then touch .
Battery Manager Information Tab
The Battery Manager displays detailed information about battery charging, health, and status.
Table 2 Battery Icon Description
Battery Icon Description
Battery charge level is between 85% and 100%.
Battery charge level is between 19% and 84%.
Battery charge level is between 0% and 18%.
• Level - The current battery charge level as a percentage. Displays -% when level is unknown.
• Wear - The health of the battery in graphical form. When the wear level exceeds 80%, the bar color changes to red.
• Health - The health of the battery. If a critical error occurs, appears. Touch to view the error description.
• Decommission - The battery is past its useful life and should be replaced. See system administrator.
• Good - The battery is good.
• Charge error - An error occurred while charging. See system administrator.
• Over Current - An over-current condition occurred. See system administrator.
45
Applications
• Dead - The battery has no charge. Replace the battery.
• Over Voltage - An over-voltage condition occurred. See system administrator.
• Below Temperature - The battery temperature is below the operating temperature. See system administrator.
• Failure Detected - A failure has been detected in the battery. See system administrator.
• Unknown - See system administrator.
• Charge Status
• Not charging - The device is not connected to AC power.
• Charging-AC - The device is connected to AC power and charging.
• Charging-USB - The device is connected to a host computer with a USB cable and charging.
• Discharging - The battery is discharging.
• Full - That the battery is fully charged.
• Unknown - The battery status is unknown.
• Time until Full - The amount of time until the battery is fully charged.
• Time since charging - The amount of time since the device began charging.
• Time until empty - The amount of time until the battery is empty.
• Advanced info - Touch to view additional battery information.
• Battery present status - Indicates that the battery is present.
• Battery level - The battery charge level as a percentage of scale.
• Battery scale - The battery scale level used to determine battery level (100).
• Battery voltage - The current battery voltage in millivolts.
• Battery temperature - The current battery temperature in degrees Centigrade.
• Battery technology - The type of battery.
• Battery current - The average current into or out of the battery over the last second in mAh.
• Battery manufacture date - The date of manufacture.
• Battery serial number - The battery serial number. The number matches the serial number printed on the battery label.
• Battery part number - The battery part number.
• Battery decommission status - Indicates if the battery is past its life span.
• Battery Good - The battery is in good health.
• Decommissioned Battery - The battery is past its useful life and should be replaced.
• Base cumulative charge - Cumulative charge using Zebra charging equipment only.
• Battery present capacity - Maximum amount of charge that could be pulled from the battery under the present discharge conditions if the battery were fully charged.
• Battery health percentage - With a range from 0 to 100 , this is the ratio of “present_capacity” to
“design_capacity” at a discharge rate of “design_capacity”.
• % decommission threshold - The default % decommission threshold for a gifted battery as 80%.
• Battery present charge Amount of usable charge remaining in the battery at present under the current discharge conditions.
46
Applications
• Battery total cumulative charge The total accumulated charge in all chargers.
• Battery time since first use The time passed since the battery was placed in a Zebra terminal for the first time.
• Battery error status - The error status of the battery.
• App version - The application version number.
47
Applications
Camera
NOTE: The device saves photos and videos on the microSD card, if installed and the storage path is changed manually. By default, or if a microSD card is not installed, the device saves photos and videos on the internal storage.
This section provides information for taking photos and recording videos using the integrated digital cameras.
Taking Photos
NOTE: See
for camera setting descriptions.
1.
Swipe up from the bottom of the Home screen and touch Camera .
5.
6.
2.
3.
4.
If necessary, touch the Camera Mode icon and touch .
Frame the subject on the screen.
To zoom in or out, press two fingers on the display and pinch or expand fingers. The zoom controls appear on the screen.
Touch an area on the screen to focus. The focus circle appears. The two bars turn green when in focus.
Touch .
The camera takes a photo and a shutter sound plays.
The photo momentarily displays as a thumbnail in the lower left corner.
48
Applications
Taking a Panoramic Photo
Panorama mode creates a single wide image by panning slowly across a scene.
1.
Swipe up from the bottom of the Home screen and touch Camera .
2.
3.
4.
5.
Touch the Camera Mode icon and touch .
Frame one side of the scene to capture.
Touch and slowly pan across the area to capture. A small white square appears inside the button indicating the capture is in progress.
If you are panning too quickly, the message Too fast appears.
Touch to end the shot. The panorama appears immediately and a progress indicator displays while it saves the image.
Recording Videos
1.
2.
Swipe up from the bottom of the Home screen and touch Camera .
Touch the camera mode menu and touch .
49
Applications
Settings
Audio
Camera
Flip
Color
Effect
Camera
Mode
Shutter
Button
Thumbnail
3.
4.
Point the camera and frame the scene.
To zoom in or out, press two fingers on the display and pinch or expand fingers. The zoom controls appear on the screen.
5.
Touch to start recording.
The video time remaining appears in the top left of the screen.
6.
Touch to end the recording.
The video momentarily displays as a thumbnail in the lower left corner.
Photo Settings
In Photo mode, photo settings appear on screen. Touch to display the photo settings options.
Rear Camera Photo Settings
• Flash - Select whether the camera relies on its light meter to decide whether a flash is necessary, or to turn it on or off for all shots.
•
• Off - Disable flash.
Auto - Adjust flash automatically depending upon light meter (default).
• On - Enable flash upon taking a photo.
• Picture size - The size (in pixels) of the photo to: 13M pixels (default), 8M pixels , 5M pixels , 3M pixels , HD 1080 , 2M pixels , HD720 , 1M pixels , WVGA , VGA, or QVGA .
• Picture quality - Set the picture quality setting to: Low , Standard or High (default).
• Countdown timer - Select Off (default), 2 seconds , 5 seconds or 10 seconds .
• Storage – Set the location to store the photo to: Phone or SD Card .
50
Applications
• Continuous Shot - Select to take a series of photos quickly while holding the capture button. Off
(default) or On .
• Face Detection - Set the camera to automatically adjust the focus for faces.
• ISO - Set camera sensitivity to light to: Auto (default), ISO Auto (HJR) , ISO100 , ISO200 , ISO400 ,
ISO800 or ISO1600 .
• Exposure - Set the exposure settings to: +2 , +1 , 0 (default), -1 or -2 .
• White balance - Select how the camera adjusts colors in different kinds of light, to achieve the most natural-looking colors:
•
•
•
Incandescent
Fluorescent
Auto
- Adjust the white balance for incandescent lighting.
- Adjust the white balance for florescent lighting.
- Adjust the white balance automatically (default).
• Daylight - Adjust the white balance for daylight.
• Cloudy - Adjust the white balance for a cloudy environment.
• Redeye reduction - Helps eliminate redeye effect. Options: Disabled (default), or Enable .
• ZSL - Set the camera to immediately take a picture when the button is pressed (default – enabled).
• Shutter Sound - Select to play a shutter sound when taking a photo. Options: Disable (default) or
Enable .
• Anti Banding - Allows the camera to avoid problems caused by artificial light sources that are not constant. These sources cycle (flicker) fast enough to go unnoticed to the human eye, appearing continuous. The camera’s eye (its sensor) can still see this flicker. Options: Auto (default), 60 Hz , 50
Hz , or Off .
Front Camera Photo Settings
• Selfie Flash - Turns screen white to help produce a little extra light in dimmer settings. Options: Off
(default), or On .
• Picture size - Set the size (in pixels) of the photo to: 5M pixels (default), 3M pixels , HD1080 , 2M pixels , HD720 , 1M pixels , WVGA , VGA, or QVGA .
• Picture quality - Set the picture quality setting to: Low , Standard or High (default).
• Countdown timer - Set to: Off (default), 2 seconds , 5 seconds or 10 seconds .
• Storage – Set location to store the photo to: Phone or SD Card .
• Continuous Shot - Select to take a series of photos quickly while holding the capture button. Off
(default) or On .
• Face Detection - Select to turn face detection Off (default) or On .
• ISO - Set how sensitive the camera is to light. Options: Auto (default), ISO Auto (HJR) , ISO100 ,
ISO200 , ISO400 , ISO800 or ISO1600 .
• Exposure - Touch to adjust the exposure settings. Options: +2 , +1 , 0 (default), -1 or -2 .
• White balance - Select how the camera adjusts colors in different kinds of light, to achieve the most natural-looking colors:
•
• Incandescent - Adjust the white balance for incandescent lighting.
Fluorescent - Adjust the white balance for florescent lighting.
51
Applications
•
• Auto - Adjust the white balance automatically (default).
Daylight - Adjust the white balance for daylight.
• Cloudy - Adjust the white balance for a cloudy environment.
• Redeye reduction - Helps eliminate redeye effect. Options: Disabled (default), or Enable .
• ZSL - Set the camera to immediately take a picture when the button is pressed (default – enabled)
• Selfie Mirror - Select to save a mirror image of the photo. Options: Disable (default), or Enable .
• Shutter Sound - Select to play a shutter sound when taking a photo. Options: Disable (default) or
Enable .
• Anti Banding - Allows the camera to avoid problems caused by artificial light sources that are not constant. These sources cycle (flicker) fast enough to go unnoticed to the human eye, appearing continuous. The camera’s eye (its sensor) can still see this flicker. Options: Auto (default), 60 Hz , 50
Hz , or Off .
Video Settings
In Video mode, video settings appear on screen. Touch to display the video settings options.
Rear Camera Video Settings
• Flash - Select whether Rear-facing Camera relies on its light meter to decide whether a flash is necessary, or to turn it on or off for all shots.
• Off - Disable flash (default).
• On - Enable flash.
• Video quality - Set video quality to: 4k DCI , 4k UHD , HD 1080p (default), HD 720p , SD 480p, VGA,
CIF, or QVGA .
• Video duration - Set to: 30 seconds (MMS) , 10 minutes , 30 minutes (default), or no limit .
• Storage – Set the location to store the photo to: Phone (default) or SD Card .
• White balance - Select how the camera adjusts colors in different kinds of light, to achieve the most natural-looking colors.
•
• Incandescent - Adjust the white balance for incandescent lighting.
Fluorescent - Adjust the white balance for florescent lighting.
•
• Auto - Adjust the white balance automatically (default).
Daylight - Adjust the white balance for daylight.
• Cloudy - Adjust the white balance for a cloudy environment.
• Image Stabilization - Set to reduce blurry videos due to device movement. Options: On or Off
(default).
Front Camera Video Settings
• Video quality - Set video quality to: HD1080p (default), HD 720p , SD 480p , VGA , CIF , or QVGA .
• Video duration - Set to: 30 seconds (MMS) , 10 minutes , 30 minutes (default) , or no limit .
52
Applications
• Storage – Set the location to store the photo to: Phone (default) or SD Card .
• White balance - Select how the camera adjusts colors in different kinds of light, to achieve the most natural-looking colors.
•
•
•
Incandescent
Fluorescent
Auto
- Adjust the white balance for incandescent lighting.
- Adjust the white balance for florescent lighting.
- Adjust the white balance automatically (default).
• Daylight - Adjust the white balance for daylight.
• Cloudy - Adjust the white balance for a cloudy environment.
• Image Stabilization - Set to reduce blurry videos due to device movement. Options: On or Off
(default).
DataWedge Demonstration
Use DataWedge Demonstration (DWDemo) to demonstrate data capture functionality. To configure
DataWedge, refer to techdocs.zebra.com/datawedge/ .
NOTE: DataWedge is enabled on the Home screen. To disable this feature, go to the DataWedge settings and disable the Launcher profile.
Table 3 DataWedge Demonstration Icons
Icon
Illumination
Description
Imager illumination is on. Touch to turn illumination off.
Data Capture
Imager illumination is off. Touch to turn illumination on.
Indicates a USB scanner is connected to the device.
Scan Mode
Menu
Indicates a USB scanner is not connected to the device.
A Bluetooth scanner is connected.
A Bluetooth scanner is not connected.
The data capture function is through the rear camera.
Imager is in picklist mode. Touch to change to normal scan mode.
Imager is in normal scan mode. Touch to change to picklist mode.
Opens a menu to view the application information or to set the application DataWedge profile.
53
Applications
Scanner Selection
To select a scanner, touch > Settings > Scanner selection .
See the Data Capture section for more information.
Press the scanner trigger button or touch the on-screen yellow scan button to capture data. The data appears in the text field below the yellow button.
54
Applications
RxLogger
RxLogger is a comprehensive diagnostic tool that provides application and system metrics, and diagnoses device and application issues. RxLogger logs the following information: CPU load, memory load, memory snapshots, battery consumption, power states, wireless logging, cellular logging, TCP dumps, Bluetooth logging, GPS logging, logcat, FTP push/pull, ANR dumps, etc. All generated logs and files are saved onto flash storage on the device (internal or external).
RxLogger Configuration
RxLogger is built with an extensible plug-in architecture and comes packaged with a number of plug-ins already built-in. For information on configuring RxLogger, refer to techdocs.zebra.com/rxlogger/ .
To open the configuration screen, from the RxLogger home screen touch Settings .
Configuration File
RxLogger configuration can be set using an XML file. The config.xml
configuration file is located in the
RxLogger\config folder. Copy the file from the device to a host computer using a USB connection. Edit the configuration file and then replace the XML file on the device. There is no need to stop and restart the
RxLogger service since the file change is automatically detected.
Enabling Logging
1.
2.
3.
To enable logging:
Swipe the screen up and select .
Touch Start .
Touch the Home button.
Disabling Logging
1.
2.
3.
To disable logging:
Swipe the screen up and select .
Touch Stop .
Touch the Home button.
Extracting Log Files
3.
4.
1.
2.
Connect the device to a host computer using an USB connection.
Using a file explorer, navigate to the RxLogger folder.
Copy the file from the device to the host computer.
Disconnect the device from the host computer.
Backing Up
RxLogger Utility allows the user to make a zip file of the RxLogger folder in the device, which by default contains all the RxLogger logs stored in the device.
55
Applications
To save the backup data, touch > BackupNow .
RxLogger Utility
RxLogger Utility is a data monitoring application for viewing logs in the device while RxLogger is running.
Logs and RxLogger Utility features are accessed using Main Chat Head.
Initiating the Main Chat Head
To initiate the Main Chat Head:
1.
Open RxLogger .
2.
3.
Touch > Toggle Chat Head . The Main Chat Head icon appears on the screen.
Touch and drag the Main Chat head icon to move it around the screen.
Removing the Main Chat Head
To remove the Main Chat Head icon:
1.
Touch and drag the icon. A circle with an X appears.
2.
Move the icon over the circle and then release.
Viewing Logs
To view logs:
1.
Touch the Main Chat Head icon. The RxLogger Utility screen appears.
2.
Touch a log to open it. The user can open many logs with each displaying a new sub Chat Head.
3.
If necessary, scroll left or right to view additional Sub Chat Head icons.
4.
Touch a Sub Chat Head to display the log contents.
Removing a Sub Chat Head Icon
To remove a sub chat Head icon, press and hold the icon until it disappears.
Backing Up In Overlay View
RxLogger Utility allows the user to make a zip file of the RxLogger folder in the device, which by default contains all the RxLogger logs stored in the device.
The Backup icon is always available in Overlay View.
1.
2.
Touch . The Backup dialog box appears.
Touch Yes to create the back up.
56
Applications
VC Settings
Use the VC Settings app with a third-party vehicle cradle.
Display
Enable/disable Stay awake to keep the device awake when the external power source is connected.
Screen Blanking
The optional Screen Blanking setting turns the screen off when the vehicle is moving and back on when the vehicle stops.
To use Screen Blanking, first connect a serial ports on the vehicle cradle to a user-supplied switch or relay.
• Screen Blanking - Enable/disable screen blanking feature.
• Input signal - Select the port that the screen blank cable is connected to. Options: Input 1 or Input 2 .
• Source polarity - Select blank screen option. De-select to disconnect the blank screen option.
• Blank screen delay - Set the amount of time after the device receives the signal to blank the screen.
Options 1 to 30 seconds (default - 1).
57
Data Capture
The device supports data capture using:
• integrated camera
• integrated scanner (ET51 with Integrated Scanner only)
• SE4750 Expansion Back
• Ring scanners:
• RS507 and RS507X Hands-free Imager
• RS5100 Ring Scanner
• RS6000 Ring Scanner
• Bluetooth scanners:
• DS2278, and DS3678 scanners
• USB scanners:
• LI3608, and DS3608.
Imaging
The device with an integrated 2D imager has the following features:
• Omnidirectional reading of a variety of barcode symbologies, including the most popular linear, postal,
PDF417, Digimarc, and 2D matrix code types.
• The ability to capture and download images to a host for a variety of imaging applications.
• Advanced intuitive laser aiming cross-hair and dot aiming for easy point-and-shoot operation.
The imager uses imaging technology to take a picture of a barcode, stores the resulting image in memory, and executes state-of-the-art software decoding algorithms to extract the barcode data from the image.
Scanning Considerations
Typically, scanning is a simple matter of aim, scan, and decode, with a few quick trial efforts to master it.
However, consider the following to optimize scanning performance:
• Range: Scanners decode best over a particular working range — minimum and maximum distances from the barcode. This range varies according to barcode density and scanning device optics. Scan within range for quick and constant decodes; scanning too close or too far away prevents decodes.
Move the scanner closer and further away to find the right working range for the barcodes being scanned.
58
• Angle: Scanning angle is important for quick decodes. When the illumination/flash reflects directly back into the imager, the specular reflection can blind/saturate the imager. To avoid this, scan the barcode so that the beam does not bounce directly back. Do not scan at too sharp an angle; the scanner needs to collect scattered reflections from the scan to make a successful decode. Practice quickly shows what tolerances to work within.
• Hold the device farther away for larger symbols.
• Move the device closer for symbols with bars that are close together.
NOTE: Scanning procedures depend on the app and device configuration. An app may use different scanning procedures from the one listed above.
Expansion Back
The Expansion Back is a bar code scanning solutions for both 1D and 2D bar code symbologies that attach to the tablet. Expansion Back is available for the 8.4" and 10.1” tablet.
Install the Expansion Back prior to use. Refer to the ET51/56 Integration Guide for installation instructions.
Integrated Scanner
The ET51 Enterprise Tablet with Integrated Scanner contains a built-in 2D scan engine for both 1D and 2D bar code symbologies.
Scanning with SE4750 Expansion Back
To read a barcode, a scan-enabled app is required. The device contains the DataWedge app that allows the user to enable the scanner to decode barcode data and display the barcode content.
To scan with the SE4750 Expansion Back:
1.
Ensure that an app is open on the device and a text field is in focus (text cursor in text field).
2.
Point the Expansion Back exit window at a bar code.
Figure 1 Bar Code Scanning with Expansion Back with SE4750
3.
Press and hold the Scan button.
The red laser aiming pattern turns on to assist in aiming. Ensure the bar code is within the area formed by the cross-hairs in the aiming pattern. The aiming dot is used for increased visibility in bright lighting conditions.
The Expansion Back beeps to indicate the bar code was decoded successfully.
59
Figure 2 SE4750 Expansion Back Aiming Pattern
Release the Scan button. The bar code data displays on the screen.
Scanning with the Integrated Scanner
To read a barcode, a scan-enabled app is required. Devices that contain the Zebra DataWedge app allows you to enable the scanner to decode barcode data and display the barcode content.
To scan with the integrated scanner:
1.
Ensure that an app is open on the device and a text field is in focus (text cursor in text field).
2.
Point the device at a barcode.
3.
4.
Press and hold one of the triggers.
Ensure the barcode is within the area formed by the aiming pattern. The aiming dot increases visibility in bright lighting conditions.
A beep sounds to indicate the barcode was decoded successfully. When the Integrated Scanner is in
Pick List mode, the device does not decode the barcode until the aiming dot touches the barcode.
60
Figure 3 Integrated Scanner Aiming Pattern
Figure 4 Integrated Scanner Pick List Mode with Multiple Barcodes in Aiming Pattern
5.
The captured data appears in the text field.
Scanning with RS507/RS507X Hands-Free Imager
Use the RS507/RS507X Hands-Free Imager to capture barcode data.
Figure 5 RS507/RS507X Hands-Free Imager
Refer to the RS507/RS507X Hands-free Imager Product Reference Guide for more information.
NOTE: To read a barcode, a scan-enabled app is required. The device contains the DataWedge app that allows you to enable the scanner to decode barcode data and display the barcode content.
To scan with the RS507/RS507X:
1.
Pair the RS507/RS507X with the device. See Pairing the Bluetooth Ring Scanner on page 69
for more information.
2.
Ensure that an app is open on the device and a text field is in focus (text cursor in text field).
61
3.
Point the RS507/RS507X at a barcode.
4.
Press and hold the trigger.
The red laser aiming pattern turns on to assist in aiming. Ensure the barcode is within the area formed by the cross-hairs in the aiming pattern. The aiming dot increases visibility in bright lighting conditions.
Figure 6 RS507/RS507X Aiming Pattern
When the RS507/RS507X is in Pick List mode, the RS507/RS507X does not decode the barcode until the center of the crosshair touches the barcode.
Figure 7 RS507/RS507X Pick List Mode with Multiple Barcodes in Aiming Pattern
The RS507/RS507X LEDs light green and a beep sounds to indicate the barcode was decoded successfully.
The captured data appears in the text field.
62
Scanning with RS5100 Ring Scanner
Use the RS5100 Ring Scanner to capture barcode data.
Figure 8 RS5100 Ring Scanner
Refer to the RS5100 Ring Scanner Product Reference Guide for more information.
NOTE: To read a barcode, a scan-enabled app is required. The device contains the DataWedge app that allows you to enable the scanner to decode barcode data and display the barcode content.
To scan with the RS5100:
1.
Pair the RS5100 with the device. See Pairing Using Simple Serial Interface or Pairing Using Bluetooth
Human Interface Device for more information.
2.
Ensure that an app is open on the device and a text field is in focus (text cursor in text field).
3.
Point the RS5100 at a barcode.
4.
Press and hold the trigger.
The red laser aiming pattern turns on to assist in aiming. Ensure the barcode is within the area formed by the cross-hairs in the aiming pattern. The aiming dot increases visibility in bright lighting conditions.
63
Figure 9 RS5100 Aiming Pattern
When the RS5100 is in Pick List mode, the RS5100 does not decode the barcode until the center of the crosshair touches the barcode.
Figure 10 RS5100 Pick List Mode with Multiple Barcodes in Aiming Pattern
The RS5100 LEDs light green and a beep sounds to indicate the barcode was decoded successfully.
The captured data appears in the text field.
Scanning with the RS6000 Bluetooth Ring Scanner
Use the RS6000 Corded Imager to capture barcode data.
Figure 11 RS6000 Bluetooth Ring Scanner
Refer to the RS6000 Bluetooth Ring Scanner Product Reference Guide for more information.
NOTE: To read a barcode, a scan-enabled app is required. The device contains the DataWedge app that allows you to enable the scanner to decode barcode data and display the barcode content.
To scan with the RS6000:
64
1.
Pair the RS6000 with the device. See Pairing Using Bluetooth Human Interface Device for more information.
2.
Ensure that an app is open on the device and a text field is in focus (text cursor in text field).
3.
Point the RS6000 at a barcode.
4.
Press and hold the trigger.
The red laser aiming pattern turns on to assist in aiming. Ensure the barcode is within the area formed by the cross-hairs in the aiming pattern. The aiming dot increases visibility in bright lighting conditions.
Figure 12 RS6000 Aiming Pattern
When the RS6000 is in Pick List mode, the RS6000 does not decode the barcode until the center of the crosshair touches the barcode.
Figure 13 RS6000 Pick List Mode with Multiple Barcodes in Aiming Pattern
The RS6000 LEDs light green and a beep sounds to indicate the barcode was decoded successfully.
The captured data appears in the text field.
65
Scanning with the DS3678 Digital Scanner
Use the DS3678 Bluetooth Scanner to capture barcode data.
Figure 14 DS3678 Digital Scanner
Refer to the DS36X8 Digital Scanner Product Reference Guide for more information.
NOTE: To read a barcode, a scan-enabled app is required. The device contains the DataWedge app that allows you to enable the scanner to decode barcode data and display the barcode content.
To scan with the DS3678:
1.
Pair the scanner with the device. For more information, see Pairing Bluetooth Scanners.
2.
Ensure that an app is open on the device and a text field is in focus (text cursor in text field).
3.
Point the scanner at a barcode.
66
4.
Press and hold the trigger.
Ensure the barcode is within the area formed by the aiming pattern. The aiming dot increases visibility in bright lighting conditions.
The captured data appears in the text field.
Scanning with the DS2278 Digital Scanner
Use the DS2278 Digital Scanner to capture barcode data.
Figure 15 DS2278 Digital Scanner
Refer to the DS2278 Digital Scanner Product Reference Guide for more information.
NOTE: To read a barcode, a scan-enabled app is required. The device contains the DataWedge app that allows you to enable the scanner to decode barcode data and display the barcode content.
To scan with the DS2278:
1.
Pair the DS2278 with the device. See Pairing a Bluetooth Scanner on page 71
for more information.
2.
Ensure that an app is open on the device and a text field is in focus (text cursor in text field).
3.
Point the scanner at a barcode.
67
4.
Press and hold the trigger.
5.
Ensure the aiming pattern covers the barcode.
Upon successful decode, the scanner beeps and the LED flashes, and the scan line turns off.
The captured data appears in the text field.
Scanning with the DS8178 Scanner
Use the DS8178 Bluetooth Scanner to capture barcode data.
Figure 16 DS8178 Digital Scanner
Refer to the DS8178 Digital Scanner Product Reference Guide for more information.
NOTE: To read a barcode, a scan-enabled app is required. The device contains the DataWedge app that allows you to enable the scanner to decode barcode data and display the barcode content.
68
To scan with the DS8178:
1.
Pair the DS8178 with the device. See Pairing a Bluetooth Scanner on page 71
for more information.
2.
Ensure that an app is open on the device and a text field is in focus (text cursor in text field).
3.
Point the scanner at a barcode.
Figure 17 Barcode Scanning with DS8178
4.
Press and hold the trigger.
5.
Ensure the aiming pattern covers the barcode.
Upon successful decode, the scanner beeps and the LED flashes, and the scan line turns off.
The captured data appears in the text field.
Pairing the Bluetooth Ring Scanner
To connect the Bluetooth Ring Scanner to the device, use one of the following methods:
• Simple Serial Interface (SSI)
• Bluetooth Human Interface Device (HID) Mode.
Pairing Using Simple Serial Interface
Pair the Ring Scanner with the device using SSI.
69
1.
Swipe up from the bottom of the Home screen and touch .
2.
Using the Ring Scanner, scan the barcode on the screen.
The Ring Scanner emits a string of high/low/high/low beeps. The Scan LED flashes green indicating that the Ring Scanner is attempting to establish connection with the device. When connection is established, the Scan LED turns off and the Ring Scanner emits one string of low/high beeps.
A notification appears on the Notification panel and the icon appears in the Status bar.
Pairing Using Bluetooth Human Interface Device
Pair the Ring Scanner with the device using Human Interface Device (HID).
1.
Ensure that Bluetooth is enabled on both devices.
2.
Ensure that the Bluetooth device to discover is in discoverable mode.
3.
Ensure that the two devices are within 10 meters (32.8 feet) of one another.
4.
Place the Ring Scanner in HID mode. If the Ring Scanner is already in HID mode, skip to step 5.
a.
Remove the battery from the Ring Scanner.
b.
Press and hold the Restore key.
c.
Install the battery onto the Ring Scanner.
d.
Keep holding the Restore key for about five seconds until a chirp is heard and the Scan LEDs flash green.
e.
Scan the barcode below to place the Ring Scanner in HID mode.
70
Figure 18 RS507/RS507x Ring Scanner Bluetooth HID Barcode
Figure 19 RS5100 / RS6000 Ring Scanner Bluetooth HID Barcode
5.
Remove the battery from the Ring Scanner.
6.
Re-install the battery into the Ring Scanner.
7.
Swipe down from the Status bar to open the Quick Access panel and then touch .
8.
Touch Bluetooth .
9.
Touch Pair new device . The device begins searching for discoverable Bluetooth devices in the area and displays them under Available devices .
10.
Scroll through the list and select Ring Scanner.
The device connects to the Ring Scanner and Connected appears below the device name. The
Bluetooth device is added to the Paired devices list and a trusted (“paired”) connection is established.
A notification appears on Notification panel and the icon appears in the Status bar.
Pairing a Bluetooth Scanner
Connect the scanner to the device using one of the following methods:
• Simple Serial Interface (SSI) mode
• Bluetooth Human Interface Device (HID) mode.
Pairing Using Simple Serial Interface
To pair the scanner with the device using SSI:
1.
Ensure that the two devices are within 10 meters (32.8 feet) of one another.
2.
Install the battery into the scanner.
3.
On the device swipe up from the bottom of the Home screen and touch .
71
Figure 20 Bluetooth Pairing Utility
4.
Using the scanner, scan the barcode on the screen.
The scanner emits a high/low/high/low beeps. The Scan LED flashes green indicating that the scanner is attempting to establish connection with the device. When connection is established, the Scan LED turns off and the scanner emits one string of low/high beeps.
5.
On the device touch the Home button.
Pairing Using Bluetooth Human Interface Device
To pair the scanner with the device using HID:
1.
Remove the battery from the scanner.
2.
Replace the battery.
3.
After the scanner reboots, scan the barcode below to place the scanner in HID mode.
4.
On the device, swipe down from the Status bar to open the Quick Access panel and then touch .
5.
Touch Bluetooth .
6.
Touch Pair new device . The device begins searching for discoverable Bluetooth devices in the area and displays them under Available devices .
72
7.
Scroll through the list and select XXXXX xxxxxx, where XXXXX is the scanner and xxxxxx is the serial number.
The device connects to the scanner, the scanner beeps once and Connected appears below the device name. The Bluetooth device is added to the Paired devices list and a trusted (“paired”) connection is established.
Connecting a USB Scanner
To connect a USB scanner, use one of the following methods:
• Simple Serial Interface (SSI) mode
• Human Interface Device (HID) mode.
Connecting Using Simple Serial Interface
To connect a USB scanner using SSI mode:
1.
Connect the scanner cable USB connector to the USB port of the device (using a third-party USC-A to
USB-C adapter) or to a vehicle cradle. The scanner beeps.
2.
Ensure that the scanner is in SSI mode. Refer to the Refer to the DS36X8 Product Reference Guide and scan the SSI Over USB CDC barcode.
Connecting Using HID Mode
To connect a USB scanner using HID mode:
1.
Connect the scanner cable USB connector to the USB port of the device (using a third-party USC-A to
USB-C adapter) or to a vehicle cradle. The scanner beeps.
2.
Ensure that the scanner is in HID mode. Refer to the Refer to the DS36X8 Product Reference Guide and scan the HID Keyboard barcode or perform a factory reset.
DataWedge
DataWedge is a utility that adds advanced barcode scanning capability to any application without writing code. It runs in the background and handles the interface to built-in barcode scanners. The captured barcode data is converted to keystrokes and sent to the target application as if it was typed on the keypad.
DataWedge allows any app on the device to get data from input sources such as a barcode scanner, MSR,
RFID, voice, or serial port and manipulate the data based on options or rules.
Configure DataWedge to:
• Provide data capture services from any app.
• Use a particular scanner, reader or other peripheral device.
• Properly format and transmit data to a specific app.
To configure DataWedge refer to techdocs.zebra.com/datawedge/ .
Enabling DataWedge
1.
2.
Swipe up from the bottom of the Home screen and touch .
Touch > Settings .
73
3.
4.
Touch the DataWedge enabled checkbox. A blue checkmark appears in the checkbox indicating that
DataWedge is enabled.
Touch the Home button.
Disabling DataWedge
1.
Touch .
2.
3.
Touch Settings .
Touch DataWedge enabled .
The blue check disappears from the checkbox indicating that DataWedge is disabled.
Supported Decoders
NOTE: DataWedge supports the decoders listed below but not all are validated on this device.
Table 4 Supported Decoders
Decoders
Australian Postal
Aztec
Canadian Postal
Chinese 2 of 5
Codabar
Code 11
Code 128
Code 39
Code 93
Composite AB
Composite C
Discrete 2 of 5
Datamatrix
O
X
X
X
O
X
O
O
O
O
O
O
X
O
X
X
X
O
X
O
O
O
O
O
O
X
O
X
X
X
O
X
O
O
O
O
O
O
X
74
O
X
X
X
O
X
O
O
O
O
O
O
X
O
X
X
X
O
X
--
O
O
O
O
O
X
O
X
X
X
O
X
O
O
O
O
O
O
X
O
X
X
X
O
X
--
O
O
O
O
O
X
O
X
X
X
O
X
--
O
O
O
O
O
X
O
X
X
X
O
X
--
O
O
O
O
O
X
Table 4 Supported Decoders (Continued)
Decoders
Dutch Postal
DotCode
EAN13
EAN8
Grid Matrix
GS1 DataBar
GS1 DataBar
Expanded
X
GS1 DataBar Limited O
O
X
X
X
O
X
GS1 Datamatrix
GS1 QRCode
HAN XIN
Interleaved 2 of 5
Japanese Postal
Korean 3 of 5
MAIL MARK
Matrix 2 of 5
Maxicode
MicroPDF
MicroQR
MSI
PDF417
QR Code
Decoder Signature
TLC 39
Trioptic 39
UK Postal
UPCA
X
O
O
X
O
O
O
X
O
X
O
O
O
O
O
O
O
O
X
X
O
O
X
O
O
O
X
O
X
O
O
O
O
X
--
O
O
O
O
O
X
X
X
X
O
O
X
O
O
X
O
O
O
X
O
X
O
O
O
O
X
O
O
O
O
O
O
X
X
X
X
O O
N/A O
X
X
O
X
X
X
O
O
X
O
O
O
X
O
X
O
O
O
O
X
O
O
O
O
O
75
X
--
O
X
O
O
O
X
O
X
O
O
O
O
X
O
O
O
O
O
O
X
X
X
X
O
O
X
O
O
X
O
O
O
X
O
X
O
O
O
O
X
--
O
O
O
O
O
X
X
X
X
O
O
X
O
O
X
O
O
O
X
O
X
O
O
O
O
--
--
O
O
--
--
O
X
X
X
X
O
O
X
O
O
X
O
O
O
X
O
X
O
O
O
O
X
O
O
O
O
O
O
X
X
X
X
O
O
X
--
O
X
O
O
O
X
O
X
O
O
O
O
X
--
O
O
O
O
O
X
X
X
X
O
O
Table 4 Supported Decoders (Continued)
Decoders
UPCE0
UPCE1
US4state
US4state FICS
US Planet
US Postnet
O
O
X
O
O
O
O
O
X
O
O
O
O
O
X
O
O
O
O
O
X
O
O
O
Key
X = Enabled
O = Disabled
-- = Not Supported
Touch the Back button to return to the previous screen.
O
O
X
O
O
O
O
O
X
O
O
O
O
O
X
O
O
O
O
O
X
O
O
O
O
O
X
O
O
O
76
Wireless
This section provides information on the following wireless features:
• Wireless Local Area Network (WLAN)
• Bluetooth
• Near Field Communications (NFC)
Wireless Local Area Networks
Wireless local area networks (WLANs) allow the device to communicate wirelessly inside a building.
Before using the device on a WLAN, the facility must be set up with the required hardware to run the
WLAN (sometimes known as infrastructure). The infrastructure and the device must both be properly configured to enable this communication.
Refer to the documentation provided with the infrastructure (access points (APs), access ports, switches,
Radius servers, etc.) for instructions on how to set up the infrastructure.
Once the infrastructure is set up to enforce the chosen WLAN security scheme, use the Wireless & networks settings configure the device to match the security scheme.
The device supports the following WLAN security options:
• None
• Enhanced Open
• Wireless Equivalent Privacy (WEP)
• Wi-Fi Protected Access (WPA)/WPA2 Personal (PSK)
• WPA3-Personal
• WPA/WPA2/WPA3 Enterprise (EAP)
• Protected Extensible Authentication Protocol (PEAP) - with MSCHAPV2 and GTC authentication.
• Transport Layer Security (TLS)
• Tunneled Transport Layer Security (TTLS) - with Password Authentication Protocol (PAP),
MSCHAP and MSCHAPv2 authentication
• Password (PWD)
• Lightweight Extensible Authentication Protocol (LEAP).
• WPA3-Enterprise 192-bit
The Status bar displays icons that indicate Wi-Fi network availability and Wi-Fi status.
77
Wireless
NOTE: To extend the life of the battery, turn off Wi-Fi when not in use.
Connecting to a Wi-Fi Network
To connect to a Wi-Fi network:
1.
2.
3.
Go to Settings .
Touch Wi-Fi to open the Wi-Fi screen. The device searches for WLANs in the area and lists them.
Scroll through the list and select the desired WLAN network.
4.
5.
For open networks, touch profile once or press and hold and then select Connect or for secure networks enter the required password or other credentials then touch Connect . See the system administrator for more information.
The device obtains a network address and other required information from the network using the dynamic host configuration protocol (DHCP) protocol. To configure the device with a fixed internet
protocol (IP) address, see Configuring the Device to Use a Static IP Address on page 81
.
In the Wi-Fi setting field, Connected appears indicating that the device is connected to the WLAN.
Removing a Wi-Fi Network
To remove a remembered or connected network:
1.
2.
3.
4.
5.
6.
Go to Settings .
Touch Network & Internet > W-Fi .
Scroll down to the bottom of the list and touch Saved networks .
Touch the name of the network.
Touch FORGET .
Touch the Home button.
WLAN Configuration
This section provides information on configuring Wi-Fi settings.
Configuring a Secure Wi-Fi Network
3.
4.
1.
2.
5.
6.
7.
8.
Go to Settings .
Touch Network & Internet > Wi-Fi .
Slide the switch to the ON position.
The device searches for WLANs in the area and lists them on the screen.
Scroll through the list and select the desired WLAN network.
Touch the desired network. If the network security is Open , the device automatically connects to the network. For all other network security a dialog box appears.
If the network security is WPA/WPA2-Personal, WPA3-Personal, or WEP, enter the required password and then touch Connect .
If the network security is WPA/WPA2/WPA3 Enterprise:
78
Wireless
9.
• Touch the EAP method drop-down list and select one of the following:
• PEAP
• TLS
• TTLS
• PWD
• LEAP .
• Touch the Phase 2 authentication drop-down list and select an authentication method.
• If required, touch CA certificate and select a Certification Authority (CA) certificate. Note:
Certificates are installed using the Security settings.
• If required, touch User certificate and select a user certificate. Note: User certificates are installed using the Security settings.
• If required, in the Identity text box, enter the username credentials.
• If desired, in the Anonymous identity text box, enter an anonymous identity username.
• If required, in the Password text box, enter the password for then given identity.
If the network security is WPA3-Enterprise 192-bit :
• Touch CA certificate and select a Certification Authority (CA) certificate. Note: Certificates are installed using the Security settings.
• Touch User certificate and select a user certificate. Note: User certificates are installed using the
Security settings.
• In the Identity text box, enter the username credentials.
NOTE: By default, the network Proxy is set to None and the IP settings is set to DHCP . See Configuring for a Proxy Server for setting connection to a proxy server and see Configuring the Device to Use a Static
IP Address for setting the device to use a static IP address.
10.
Touch Connect .
11.
Touch the Home button.
Manually Adding a Wi-Fi Network
Manually add a Wi-Fi network if the network does not broadcast its name (SSID) or to add a Wi-Fi network when out of range.
1.
2.
3.
4.
5.
6.
Go to Settings .
Touch Network & Internet > Wi-Fi .
Slide the Wi-Fi switch to the On position.
Scroll to the bottom of the list and select Add network .
In the Network name text box, enter the name of the Wi-Fi network.
In the Security drop-down list, set the type of security to:
• None
• Enhanced Open
• WEP
• WPA/WPA2-Personal
79
Wireless
7.
8.
9.
• WPA3-Personal
• WPA/WPA2/WPA3-Enterprise
• WPA3-Enterprise 192-bit
If the network security is None or Enhanced Open , touch Save .
If the network security is WEP, WPA3-Personal , or WPA/WPA2-Personal , enter the required password and then touch Save .
If the network security is WPA/WPA2/WPA3-Enterprise :
• Touch the EAP method drop-down list and select one of the following:
• PEAP
• TLS
• TTLS
• PWD
• LEAP.
• Touch the Phase 2 authentication drop-down list and select an authentication method.
• If required, touch CA certificate and select a Certification Authority (CA) certificate. Note:
Certificates are installed using the Security settings.
• If required, touch User certificate and select a user certificate. Note: User certificates are installed using the Security settings.
• If required, in the Identity text box, enter the username credentials.
• If desired, in the Anonymous identity text box, enter an anonymous identity username.
• If required, in the Password text box, enter the password for the given identity.
10.
If the network security is WPA3-Enterprise 192-bit :
• Touch CA certificate and select a Certification Authority (CA) certificate. Note: Certificates are installed using the Security settings.
• Touch User certificate and select a user certificate. Note: User certificates are installed using the
Security settings.
• In the Identity text box, enter the username credentials.
NOTE: By default, the network Proxy is set to None and the IP settings is set to DHCP
. See Configuring for a Proxy Server on page 80
for setting connection to a proxy server and see Configuring the Device to
Use a Static IP Address on page 81 for setting the device to use a static IP address.
11.
Touch Save . To connect to the saved network, touch and hold on the saved network and select
Connect to network .
12.
Touch the Home button.
Configuring for a Proxy Server
A proxy server is a server that acts as an intermediary for requests from clients seeking resources from other servers. A client connects to the proxy server and requests some service, such as a file, connection, web page, or other resource, available from a different server. The proxy server evaluates the request according to its filtering rules. For example, it may filter traffic by IP address or protocol. If the request is validated by the filter, the proxy provides the resource by connecting to the relevant server and requesting the service on behalf of the client.
80
Wireless
It is important for enterprise customers to be able to set up secure computing environments within their companies, making proxy configuration essential. Proxy configuration acts as a security barrier ensuring that the proxy server monitors all traffic between the Internet and the intranet. This is normally an integral part of security enforcement in corporate firewalls within intranets.
1.
2.
3.
4.
Go to Settings .
Touch Network & Internet > Wi-Fi .
Slide the Wi-Fi switch to the On position.
In the network dialog box, select and touch a network.
5.
6.
7.
8.
9.
Touch Advanced options .
Touch Proxy and select Manual .
In the Proxy hostname text box, enter the address of the proxy server.
In the Proxy port text box, enter the port number for the proxy server.
In the Bypass proxy for text box, enter addresses for web sites that are not required to go through the proxy server. Use a comma “,” between addresses. Do not use spaces or carriage returns between addresses.
10.
Touch Connect .
11.
Touch the Home button.
Configuring the Device to Use a Static IP Address
By default, the device is configured to use Dynamic Host Configuration Protocol (DHCP) to assign an
Internet protocol (IP) address when connecting to a wireless network.
1.
2.
3.
4.
Go to Settings .
Touch Network & Internet > Wi-Fi .
Slide the Wi-Fi switch to the On position.
In the network dialog box, select and touch a network.
5.
6.
Touch Advanced options .
Touch IP settings and select Static .
In the IP address text box, enter an IP address for the device.
7.
8.
9.
If required, in the Gateway text box, enter a gateway address for the device.
If required, in the Network prefix length text box, enter the prefix length.
10.
If required, in the DNS 1 text box, enter a Domain Name System (DNS) address.
11.
If required, in the DNS 2 text box, enter a DNS address.
12.
Touch Connect .
13.
Touch the Home button.
Wi-Fi Preferences
Use the Wi-Fi preferences to configure advanced Wi-Fi settings. From the Wi-Fi screen scroll down to the bottom of the screen and touch Wi-Fi preferences .
• Turn on Wi-Fi automatically - When enabled, Wi-Fi automatically turns back on when near high quality saved networks.
81
Wireless
• Open network notification - When enabled, notifies the user when an open network is available.
• Advanced - Touch to expand options.
• Additional settings - See Additional Settings.
• Install Certificates – Touch to install certificates.
• Network rating provider - Disabled (AOSP devices). To help determine what constitutes a good
Wi-Fi network, Android supports external Network rating providers that provide information about the quality of open Wi-Fi networks. Select one of the providers listed or None . If none are available or selected, the Connect to open networks feature is disabled.
• Wi-Fi Direct - Displays a list of devices available for a direct Wi-Fi connection.
• MAC address - Displays the Media Access Control (MAC) address of the device when connecting to Wi-Fi networks.
• IP address - Displays the IP address of the device when connecting to Wi-Fi networks.
Additional Wi-Fi Settings
NOTE: Additional Wi-Fi settings are for the device, not for a specific wireless network.
Use the Additional Settings to configure additional Wi-Fi settings. To view the additional Wi-Fi settings, scroll to the bottom of the Wi-Fi screen and touch Wi-Fi Preferences > Advanced > Additional settings.
• Regulatory
• Country Selection - Displays the acquired country code if 802.11d is enabled, else it displays the currently selected country code.
• Region code - Displays the current region code.
• Band and Channel Selection
• Wi-Fi frequency band - Set the frequency band to: Auto (default), 5 GHz only or 2.4 GHz only .
• Available channels (2.4 GHz) - Touch to display the Available channels menu. Select specific channels and touch OK .
• Available channels (5 GHz) - Touch to display the Available channels menu. Select specific channels and touch OK .
• Logging
• Advanced Logging – Touch to enable advanced logging or change the log directory.
• Wireless logs - Use to capture Wi-Fi log files.
• Fusion Logger - Touch to open the Fusion Logger application. This application maintains a history of high level WLAN events which helps to understand the status of connectivity.
• Fusion Status - Touch to display live status of WLAN state. Also provides information about the device and connected profile.
• About
• Version - Displays the current Fusion information.
82
Wireless
Wi-Fi Direct
Wi-Fi Direct devices can connect to each other without having to go through an access point. Wi-Fi Direct devices establish their own ad-hoc network when required, letting you see which devices are available and choose which one you want to connect to.
1.
2.
Go to Settings .
Touch Wi-Fi > Wi-Fi preferences > Advanced > Wi-Fi Direct . The device begins searching for another Wi-Fi Direct device.
3.
4.
Under Peer devices , touch the other device name.
On the other device, select Accept .
Connected appears on the device. On both devices, in their respective Wi-Fi Direct screens, the other device name appears in the list.
Bluetooth
Bluetooth devices can communicate without wires, using frequency-hopping spread spectrum (FHSS) radio frequency (RF) to transmit and receive data in the 2.4 GHz Industry Scientific and Medical (ISM) band (802.15.1). Bluetooth wireless technology is specifically designed for short-range (10 m (32.8 ft)) communication and low power consumption.
Devices with Bluetooth capabilities can exchange information (for example, files, appointments, and tasks) with other Bluetooth enabled devices such as printers, access points, and other mobile devices.
The device supports Bluetooth Low Energy. Bluetooth Low Energy is targeted at applications in the healthcare, fitness, security, and home entertainment industries. It provides reduced power consumption and cost while maintaining standard Bluetooth range.
Adaptive Frequency Hopping
Adaptive Frequency Hopping (AFH) is a method of avoiding fixed frequency interferers, and can be used with Bluetooth voice. All devices in the piconet (Bluetooth network) must be AFH-capable in order for AFH to work. There is no AFH when connecting and discovering devices. Avoid making Bluetooth connections and discoveries during critical 802.11b communications. AFH for Bluetooth consists of four main sections:
• Channel Classification - A method of detecting an interference on a channel-by-channel basis, or pre-defined channel mask.
• Link Management - Coordinates and distributes the AFH information to the rest of the Bluetooth network.
• Hop Sequence Modification - Avoids interference by selectively reducing the number of hopping channels.
• Channel Maintenance - A method for periodically re-evaluating the channels.
When AFH is enabled, the Bluetooth radio “hops around” (instead of through) the 802.11b high-rate channels. AFH coexistence allows enterprise devices to operate in any infrastructure.
NOTE: It is not recommended to perform Bluetooth wireless technology inquiry when high rate 802.11b operation is required.
83
Wireless
Security
The current Bluetooth specification defines security at the link level. Application-level security is not specified. This allows application developers to define security mechanisms tailored to their specific need.
Link-level security occurs between devices, not users, while application-level security can be implemented on a per-user basis. The Bluetooth specification defines security algorithms and procedures required to authenticate devices, and if needed, encrypt the data flowing on the link between the devices. Device authentication is a mandatory feature of Bluetooth while link encryption is optional.
Pairing of Bluetooth devices is accomplished by creating an initialization key used to authenticate the devices and create a link key for them. Entering a common personal identification number (PIN) in the devices being paired generates the initialization key. The PIN is never sent over the air. By default, the
Bluetooth stack responds with no key when a key is requested (it is up to user to respond to the key request event). Authentication of Bluetooth devices is based-upon a challenge-response transaction.
Bluetooth allows for a PIN or passkey used to create other 128-bit keys used for security and encryption.
The encryption key is derived from the link key used to authenticate the pairing devices. Also worthy of note is the limited range and fast frequency hopping of the Bluetooth radios that makes long-distance eavesdropping difficult.
Recommendations are:
• Perform pairing in a secure environment
• Keep PIN codes private and do not store the PIN codes in the device
• Implement application-level security.
Bluetooth Profiles
The device supports the Bluetooth services listed.
Table 5 Bluetooth Profiles
Profile
Service Discovery Protocol
(SDP)
Serial Port Profile (SPP)
Object Push Profile (OPP)
Advanced Audio Distribution
Profile (A2DP)
Audio/Video Remote Control
Profile (AVRCP)
Personal Area Network (PAN)
Human Interface Device Profile
(HID)
Headset Profile (HSP)
Description
Handles the search for known and specific services as well as general services.
Allows use of RFCOMM protocol to emulate serial cable connection between two Bluetooth peer devices. For example, connecting the device to a printer.
Allows the device to push and pull objects to and from a push server.
Allows the device to stream stereo-quality audio to a wireless headset or wireless stereo speakers.
Allows the device to control A/V equipment to which a user has access. It may be used in concert with A2DP.
Allows the use of Bluetooth Network Encapsulation Protocol to provide L3 networking capabilities over a Bluetooth link. Only
PANU role is supported.
Allows Bluetooth keyboards, pointing devices, gaming devices and remote monitoring devices to connect to the device.
Allows a hands-free device, such as a Bluetooth headset, to place and receive calls on the device.
84
Wireless
Table 5 Bluetooth Profiles (Continued)
(PBAP)
Profile
Hands-Free Profile (HFP)
Phone Book Access Profile
Out of Band (OOB)
Out of Band (OOB)
Symbol Serial Interface (SSI)
File Transfer Profile (FTP)
Description
Allows car hands-free kits to communicate with the device in the car.
Allows exchange of Phone Book Objects between a car kit and a mobile device to allow the car kit to display the name of the incoming caller; allow the car kit to download the phone book so you can initiate a call from the car display.
Allows exchange of information used in the pairing process. Pairing is completed using the Bluetooth radio, but requires information from the OOB mechanism. Using OOB with NFC enables pairing when devices simply get close, rather than requiring a lengthy discovery process.
Allows exchange of information used in the pairing process. Pairing is initiated by NFC but completed using the Bluetooth radio. Paring requires information from the OOB mechanism. Using OOB with
NFC enables pairing when devices simply get close, rather than requiring a lengthy discovery process.
Allows for communication with Bluetooth Imager.
Provides the capability to browse, manipulate and transfer files in file system of another system. Uses GOEP as a basis.
Generic Attribute Profile (GATT) Provides profile discovery and description services for Bluetooth
Low Energy protocol. It defines how attributes are grouped together into sets to form services.
HID Over GATT Profile (HOGP) Defines the procedures and features used by Bluetooth low energy
HID Devices using GATT and Bluetooth HID Hosts using GATT.
Generic Access Profile (GAP)
OBject EXchange (OBEX)
Use for device discovery and authentication.
Facilitates the exchange of binary objects between devices.
Bluetooth Power States
The Bluetooth radio is off by default.
• Suspend - When the device goes into suspend mode, the Bluetooth radio stays on.
• Airplane Mode - When the device is placed in Airplane Mode, the Bluetooth radio turns off. When
Airplane mode is disabled, the Bluetooth radio returns to the prior state. When in Airplane Mode, the
Bluetooth radio can be turned back on if desired.
Bluetooth Radio Power
Turn off the Bluetooth radio to save power or if entering an area with radio restrictions (for example, an airplane). When the radio is off, other Bluetooth devices cannot see or connect to the device. Turn on the
Bluetooth radio to exchange information with other Bluetooth devices (within range). Communicate only with Bluetooth radios in close proximity.
NOTE: To achieve the best battery life, turn off radios when not in use.
85
Wireless
Enabling Bluetooth
1.
2.
3.
Swipe down from the Status bar to open the Notification panel.
Touch to turn Bluetooth on.
Touch the Home button.
Disabling Bluetooth
1.
Swipe down from the Status bar to open the Notification panel.
2.
3.
Touch to turn Bluetooth off.
Touch the Home button.
Discovering Bluetooth Device(s)
The device can receive information from discovered devices without pairing. However, once paired, the device and a paired device exchange information automatically when the Bluetooth radio is on.
1.
2.
Ensure that Bluetooth is enabled on both devices.
Ensure that the Bluetooth device to discover is in discoverable mode.
3.
4.
Ensure that the two devices are within 10 meters (32.8 feet) of one another.
Swipe down from the Status bar to open the Quick Access panel.
5.
6.
7.
8.
9.
Touch and hold Bluetooth .
Touch Pair new device . The device begins searching for discoverable Bluetooth devices in the area and displays them under Available devices .
Scroll through the list and select a device. The Bluetooth pairing request dialog box appears.
Touch Pair on both devices.
The Bluetooth device is added to the Paired devices list and a trusted (“paired”) connection is established.
Changing the Bluetooth Name
By default, the device has a generic Bluetooth name that is visible to other devices when connected.
1.
2.
3.
Go to Settings .
Touch Connected devices > Connection preferences > Bluetooth .
If Bluetooth is not on, move the switch to turn Bluetooth on.
4.
5.
6.
Touch Device name .
Enter a name and touch RENAME .
Touch the Home button.
Connecting to a Bluetooth Device
Once paired, connect to a Bluetooth device.
1.
2.
Go to Settings .
Touch Connected devices > Connection preferences > Bluetooth .
86
Wireless
3.
In the list, touch the unconnected Bluetooth device.
When connected, Connected appears below the device name.
Selecting Profiles on the Bluetooth Device
Some Bluetooth devices have multiple profiles.
1.
2.
Go to Settings .
Touch Connected devices > Connection preferences > Bluetooth .
3.
4.
5.
In the Paired Devices list, touch next to the device name.
Turn on or off a profile to allow the device to use that profile.
Touch the Home button.
Unpairing a Bluetooth Device
3.
4.
5.
Unpairing a Bluetooth device erases all pairing information.
1.
2.
Go to Settings .
Touch Connected devices > Connection preferences > Bluetooth .
In the Paired Devices list, touch next to the device name.
Touch FORGET .
Touch the Home button.
Cast
Use Cast to mirror the device screen on a Miracast enabled wireless display.
1.
Go to Settings .
2.
Touch Connected devices > Connection preferences > Cast .
3.
Touch > Enable wireless display .
The device searches for nearby Miracast devices and lists them.
4.
5.
Touch a device to begin casting.
Touch the Home button.
Near Field Communications
NFC/HF RFID is a short-range wireless connectivity technology standard that enables secure transaction between a reader and a contactless smartcard. The technology is based on ISO/IEC 14443 type A and B
(proximity), ISO/IEC 15693 (vicinity), and FeliCa standards, using the HF 13.56 MHz unlicensed band.
The device supports the following operating modes:
• Reader mode
• Peer-to-Peer communication
• Card Emulation mode.
87
Wireless
Using NFC, the device can:
• Read contactless cards such as contactless tickets, ID cards and ePassport.
• Read and write information to contactless cards such as SmartPosters and tickets, as well as devices with NFC interface such as vending machines.
• Read information from supported medical sensors.
• Pair with supported Bluetooth devices such as printers , ring scanners (ex. RS6000), and headsets (ex.
HS3100).
• Exchange data with another NFC device.
• Emulate contactless card such as payment, or ticket.
The device NFC antenna is positioned to read NFC cards from the top of the device while the device is being held.
Reading NFC Cards
Read contactless cards using NFC.
Figure 21 Reading Cards
3.
4.
1.
2.
Launch an NFC enabled application.
Hold device as shown.
Move the device close to the NFC card until it detects the card.
Hold the card steadily until the transaction is complete (usually indicated by the application).
Enterprise NFC Settings
Improve NFC performance or increase battery life by selecting which NFC features to use on the device.
• Card Detection Mode - Select a card detection mode.
• Low - Increases battery life by lowering the NFC detection speed.
• Hybrid - Provides a balance between NFC detection speed and battery life (default).
• Standard - Provides the best NFC detection speed, but reduces battery life.
• Supported Card Technology - Select an option to detect only one NFC tag type, increasing battery life, but reducing detection speed.
• All (Default) - Detects all NFC tag types.
88
Wireless
• ISO 14443 Type A/B
• FeliCa
• ISO15693
• Other NFC settings available with Zebra administrator tools (CSP) - Allows configuration of additional Enterprise NFC Settings through staging tools and Mobile Device Management (MDM) solutions with an MX version that supports the Enterprise NFC Settings Configuration Service Provider
(CSP). For more information on using the Enterprise NFC Settings CSP, refer to: techdocs.zebra.com
.
89
Accessories
Introduction
The device accessories provide a variety of product support capabilities.
Table 6 Device Accessories
Accessory
Cradles
Charge Only Cradle
Part Number
CRD-ET5X-1SCG2
Communication and
Charging Cradle
Rugged Communication and Charging Cradle
CRD-ET5X-1SCOM1
CRD-ET5X-1SCOM2R
4-Slot Charge Only Cradle CRD-ET5X-SE4CO2-01
Description
Charges the main battery and optional
Power Pack installed in the Expansion
Back. Requires power supply
PWR-BGA12V50W0WW , DC line cord
CBL-DC-388A1-01 and country-specific
AC line cord.
Charges the main battery and optional
Power Pack installed in the Expansion
Back. Requires power supply
PWR-BGA12V50W0WW , DC line cord
CBL-DC-388A1-01, and country-specific
AC line cord.
Charges the main battery and optional
Power Pack installed in the Expansion
Back. Supports rugged frame and rugged
IO Adapter. Requires power supply
PWR-BGA12V50W0WW , DC line cord
CBL-DC-388A1-01, and country-specific
AC line cord.
Charges up to four main batteries and optional Power Pack installed in the
Expansion Back and up to four Power
Packs in the optional 4-Slot Battery
Charger. Requires power supply
PWR-BGA12V108W0WW , DC line cord
CBL-DC-388A1-01, and country-specific
AC line cord.
90
Accessories
Table 6 Device Accessories (Continued)
Accessory
Chargers
Power Supply
Part Number Description
Power Supply
Power Supply
4-Slot Battery Charger
PWR-BGA12V108W0WW Provides power to the 4-Slot Charge Only
Cradle.
PWR-BGA12V50W0WW Provides power to the Charge Only
Cradle, Communication and Charging
Cradle, Rugged Communication and
Charging Cradle, and 4-Slot Battery
Charger for Optional Battery Power Pack.
Provides power to the tablet using the
USB-C cable CBL-TC2X-USBC-01.
PWR-WUA5V12W0xx
Where xx:
AR = Argentina
AU = Australia
BR = Brazil
CN = China
EU = European Union
Countries
GB = Great Britain
IN = India
KR = Korea
US = United States
SAC-ET5X-4PPK1-01 Chargers up to four Power Packs.
Requires power supply
PWR-BGA12V50W0WW, DC Line cord
CBL-DC-388A1-01, and country-specific
AC line cord.
Rugged Charge Connector CHG-ET5X-CBL2-01 Charges the main battery and optional
Power Pack installed in the Expansion
Back. Requires power supply
PWR-BGA12V50W0WW , DC Line Cord
CBL-DC-388A1-01 and country-specific
AC line cord.
Miscellaneous
Replacement 8.4 in. Internal
Battery
Replacement 10.1 in.
Internal Battery
Replacement 8.4 in. Battery
Cover
Replacement 10.1 in.
Battery Cover
8.4 in. Rugged Frame with
IO Adapter
BTRY-ET5X-8IN5-01
BTRY-ET5X-10IN5-01
KT-ET5X-8BTDR2-01
KT-ET5X-10BTDR2-01
SG-ET5X-8RCSE2-02
Replacement battery for 8.4 in. tablet.
Replacement battery for 10.1 in. tablet.
Replacement battery cover for 8.4 in. tablet.
Replacement battery cover for 10.1 in. tablet.
Add extra protection for the 8.4 in. tablet and IO Adapter for connection to the
Rugged Communication and Charging
Cradle.
91
Accessories
Table 6 Device Accessories (Continued)
Accessory
10.1” Rugged Frame with
IO Adapter
Part Number
SG-ET5X-10RCSE2-01
Replacement Rugged IO
Connector
8.4 in. SE4750 Expansion
Back
8.4 in. Expansion Back
10.1” SE4750 Expansion
Back
10.1” Expansion Back
Power Pack
Passive Stylus
SG-ET5X-RGIO2-01
ZBK-ET5X-8SCN5-01
ZBK-ET5X-8RH1-01
ZBK-ET5X-10SCN5-01
ZBK-ET5X-10RH1-01
BTRY-ET5X-PRPK1-01
SG-TC7X-STYLUS-03
Replacement Expansion
Back Hand Strap
Coiled Stylus Tether
8.4 in. Operations Case
10.1” Operations Case
SG-ET5X-RHTP1-01
SG-ET5X-SLTETR-01
SG-ET5X-8HLST-01
SG-ET5X-10HLST-01
Breakaway Shoulder Strap SG-ET5X-SHDRSTP-01
Description
Add extra protection for the 10.1 in. tablet and IO Adapter for connection to the
Rugged Communication and Charging
Cradle.
Replacement rugged IO connector for the
Rugged Frames.
Provides data capture using the SE4750 scan engine, rotating hand strap and slot for optional Power Pack.
Provides rotating hand strap and slot for optional Power Pack.
Provides data capture using the SE4750 scan engine, rotating hand strap and slot for optional Power Pack.
Provides rotating hand strap and slot for optional Power Pack.
Provides additional power for charging the device battery using an Expansion Back.
Provides easy writing, drawing, and navigation and accuracy with the thin tip and hovering capabilities.
Replacement hands strap for Expansion
Backs.
Secures a stylus to the hand strap.
Provides carrying solution for 8.4 in. tablet.
Provides carrying solution for 10.1 in. tablet.
Use with the Operations Case and D-clips to carry tablet on shoulder.
Battery Charging
Main Battery Charging
The 8.4 in. tablet main battery charges from fully depleted to 90% in approximately 2 hours and from fully depleted to 100% in approximately 3 hours.
The 10.1 in. tablet main battery charges from fully depleted to 90% in approximately 3 hours and from fully depleted to 100% in approximately 5 hours.
NOTE: The Charging indicator only illuminates when the device is connected to AC power.
92
Accessories
Table 7 Charging Indicator
LED
Off
Blinking Orange
Green
Red
Indication
Device is not in cradle; not seated properly; or cradle is not powered.
Device is charging.
Charging complete.
Error in charging; check placement of the device.
Charging Temperature
Charge batteries in ambient temperatures from 0°C to +40°C (32°F to 104°F) as reported by the battery.
Charging is intelligently controlled by the charger. To accomplish this, for small periods of time, the charger alternately enables and disables battery charging to keep the battery at acceptable temperatures.
93
Accessories
Charge Only Cradle
CAUTION: Ensure that you follow the guidelines for battery safety described in
Battery Safety Guidelines on page 153 .
NOTE: The Charge Only Cradle (CRD-ET5X-1SCG2) comes with two inserts; tall insert and short insert.
Install the tall insert when using a device without a Rugged Frame or Expansion Back. Install the small insert when using with an Expansion Back and without a Rugged Frame.
The Charge Only Cradle does not support the ET51 Enterprise Tablet with Integrated Scanner.
This section describes how to use a Charge Only Cradle with the device.
The Charge Only Cradle:
• Provides power for operating the device.
• Charges the device’s battery and optional Power Pack installed in an Expansion Back.
Figure 22 Charge Only Cradle - Front View
1
3
4
1
2
2
Guide pins
Charging pins
Small insert
Tall insert
3
Figure 23 Charge Only Cradle - Rear View
1
94
4
Accessories
1 Power input
Installing the Insert
Install the tall insert when using a device without a Rugged Frame or Expansion Back. Install the small insert when using an device with an Expansion Back and without a Rugged Frame.
1.
Align the insert over the pins.
2.
Press the insert down until it seats flush in the cradle.
Charging the Device
To charge the device in the Charge Only Cradle:
1.
Align the device with the alignment pins on the cradle.
2.
Insert the device into the cradle.
NOTE: Ensure the tablet is flat on the cradle and all charging contacts are touching the charging base.
95
Accessories
3.
4.
The device Charging LED indicates charging.
To remove the device from the Charge Only Cradle, hold the cradle down with one hand and lift the device.
96
Accessories
Communication and Charging Cradle
CAUTION: Ensure that you follow the guidelines for battery safety described in
Battery Safety Guidelines on page 153 .
NOTE: The Communication and Charging Cradle (CRD-ET5X-1SCOM2) comes with two inserts; tall insert and short insert. Install the tall insert when using without a Rugged Frame or Expansion Back. Install the small insert when using with an Expansion Back and without a Rugged Frame.
The Communication and Charging Cradle does not support the ET51 Enterprise Tablet with Integrated
Scanner.
This section describes how to use a Communication and Charing Cradle with the tablet.
The Communication and Charging cradle:
• Provides power for operating the tablet.
• Provides ports for connecting USB devices to the tablet, video output and connection to a LAN.
• Charges the tablet’s battery and optional Power Pack installed in an Expansion Back.
Figure 24 Communication and Charging Cradle - Front View
1
7
5
6
7
3
4
1
2
6 5
Docking connector
Tall insert
Short insert
Release button
Locking latches
Charging pins
Guide pins
4 3
97
2
Accessories
Figure 25 Communication and Charging Cradle - Rear View
3
4
1
2
4
LAN (RJ45) port
HDMI port
USB 3.0 ports
Power input
3 2 1
Figure 26 Communication and Charging Cradle - Setup
Installing the Insert
Install the tall insert when using a device without a Rugged Frame or Expansion Back. Install the small insert when using a device with an Expansion Back and without a Rugged Frame.
98
1.
Align the insert over the pins.
Accessories
2.
Press the insert down until it seats flush in the cradle.
Charging the Device
To charge the device in the Communication and Charging Cradle:
1.
Open the bottom access door and hold it to the back of the tablet.
2.
Align the device with the alignment pins on the cradle.
3.
Insert the device into the cradle. Note that the Communication and Charging Cradles contains a locking mechanism that locks the device to the cradle.
NOTE: Ensure the tablet is flat on the cradle and all charging contacts are touching the charging base.
4.
The device Charging LED indicates charging.
99
Accessories
5.
To remove the device from the Communication and Charging Cradle, press the release button on the right side of the cradle and lift the device. Use thumb to hold down the cradle.
100
Accessories
Rugged Communication and Charging Cradle
CAUTION: Ensure that you follow the guidelines for battery safety described in
Battery Safety Guidelines on page 153 .
This section describes how to use a Rugged Communication and Charing Cradle with the device.
The Rugged Communication and Charging cradle:
• Provides power for operating the device.
• Provides ports for connecting USB devices to the tablet, video output and connection to a LAN.
• Charges the device’s battery and optional Power Pack installed in an Expansion Back.
• Support the ET51 Enterprise Tablet with Integrated Scanner.
Figure 27 Rugged Communication and Charging Cradle - Front View
1
5
3
4
1
2
5
4 3
Rugged docking connector
Release button
Locking latches
Charging pins
Guide pins
2
101
Accessories
Figure 28 Rugged Communication and Charging Cradle - Rear View
3
4
1
2
4
LAN (RJ45) port
HDMI port
USB 3.0 ports
Power input
3 2 1
For the ET51 Enterprise Tablet with Integrated Scanner, ensure that the cradle pads are installed prior to inserting the device into the cradle.
Figure 29 Install Pads onto Cradle
Charging the Device
To charge the device using the Rugged Communication and Charging Cradle:
1.
Align the device with the alignment pins on the cradle.
2.
Insert the device into the cradle. Note that the Rugged Communication and Charging Cradles contains a locking mechanism that locks the device to the cradle.
102
Accessories
NOTE: Ensure the tablet is flat on the cradle and all charging contacts are touching the charging base.
3.
4.
The device Charging LED indicates charging.
To remove the device from the Rugged Communication and Charging Cradle, press the release button on the right side of the cradle and lift the device. Use thumb to hold down the cradle.
103
Accessories
4-Slot Charge Only Cradle
CAUTION: Ensure that you follow the guidelines for battery safety described in
Battery Safety Guidelines on page 153 .
• Provides 5 VDC power for operating the device.
• Simultaneously charges up to four devices and up to four Power Packs using the optional Battery
Charger Adapter.
Figure 30 4-Slot Charge Only Cradle
104
Accessories
Power Setup
Figure 31 Power Setup with Optional Charger
1
2
1
2
PWR-BGA12V108W0WW
PWR-BGA12V50W0WW
105
Accessories
Insert Installation
Install inserts into slots for device tablets without Rugged Frame.
Figure 32 Install Insert in Slot
Guide Installation
The cradle comes with four 8 in. tablets guide and four 10 in. tablet guides. Install the appropriate guides for the tablets.
1.
Align the two tabs on the guide with the two slots in the cradle.
106
Figure 33 Align Guide with Slot
Accessories
1
1 Guide tab
2. Place the guide down onto the cradle and then rotate the guide until it snaps into the cradle.
107
Accessories
Battery Charger Installation
Install optional 4-Slot Battery Charger onto cradle:
1.
Align the mounting holes on the bottom of the charger with the four studs on the cradle.
2.
Place the charger on the cradle and then slide toward the front of the cradle.
Insert Tablet into Slot
Device without Rugged Frame
1.
Install insert into slot.
108
Accessories
2.
Align the two alignment holes on the bottom of the tablet with the two alignment pins in the slot.
3.
Place the device down into the slot with display facing away from Battery Charger.
NOTE: There are rubs on the insert that prevent the tablet from being inserted in the wrong orientation.
Device with Rugged Frame
1.
2.
If applicable, remove insert from slot.
Slide device over slot into it touches the guide.
3.
Place the device down into the slot with display facing away from Battery Charger.
109
Accessories
NOTE: There are rubs on the slot that prevent the tablet from being inserted in the wrong orientation.
Battery Charger Installation
Install optional 4-Slot Battery Charger onto cradle:
1.
Align the mounting holes on the bottom of the charger with the four studs on the cradle.
2.
Place the charger on the cradle and then slide toward the front of the cradle.
110
Accessories
Rugged Charge Connector
CAUTION: Ensure that you follow the guidelines for battery safety described in
Battery Safety Guidelines on page 153 .
Use the Rugged Charge Connector to charge an device tablet.
NOTE: The Rugged Charge Connector does not support the ET51 Enterprise Tablet with Integrated
Scanner.
The Rugged Connector does not support the ET51 Enterprise Tablet with Integrated Scanner.
Figure 34 Rugged Charge Connector
1.
Align the pins in the Rugged Charge Connector with the slots in the device.
111
Accessories
2.
Plug the Power Supply connector into the Power Input Port on the Rugged Charge Connector.
112
Accessories
Power Pack
The optional Power Pack provides additional power for charging the main battery.
NOTE: If the tablet is equipped with an Expansion Back and Power Pack, it produces recurring beep alerts when there is no user activity and the internal battery is fully charged by the Power Pack. To avoid the beeping alerts, the user is advised to remove the Power Pack from the Expansion Pack once the internal battery reaches 100%.
Figure 35 Power Pack
1
2
3
1
2
3
Charge level indicators
Charge indicator button
Power output contacts
1.
2.
Install one of the optional Expansion Backs. See
Expansion Back on page 120 for more information.
Press the two release buttons on the side of the Expansion Back. The dummy battery insert ejects slightly.
1
1 Release button (2)
3.
Remove dummy battery insert.
113
Accessories
4.
Insert Power Pack into slot until it snaps into place.
Charging the Power Pack
Charge the Power Pack using:
• A cradle
• 4-Slot Charger.
Using Cradle
With the Power Pack installed in an Expansion Back, place the device into a cradle. The Power Pack charges in less than 3.5 hours.
114
Accessories
Using the 4-Slot Battery Charger
CAUTION: Ensure that you follow the guidelines for battery safety described in
Battery Safety Guidelines on page 153 .
Use the 4-Slot Battery Charger to charge up to four Power Packs.
Figure 36 4-Slot Battery Charger
Charging the Power Pack
Charge Power Packs in ambient temperatures from 0°C to +40°C (32°F to 104°F) as reported by the
Power Pack. Charging is intelligently controlled by the charger. To accomplish this, for small periods of time, the charger alternately enables and disables Power Pack charging to keep the battery at acceptable temperatures.
The Power Pack charge LED shows the status of the battery charging. The Power Pack charges in less than three hours. When charging, the Charge LEDs indicate the charge level.
Figure 37 Power Pack Charge LEDs
1
1 Charge level indicators
115
Accessories
Table 8 Power Pack Charge Status Indicators
Description
Power not applied to Power Pack.
Charge level is between 0% and 20%.
Charge level is between 20% and 40%.
Change level is between 40% and 60%.
Charge level is between 60% and 80%.
Charge level is between 80% and 100%.
Fully charged.
Charging error.
Solid Green LED
Blinking Green LED
Blinking Red LED
116
Accessories
Rugged Frame
The Rugged Frame (8.4 in. and 10.1 in.) adds additional protection to the device. Use the Rugged I/O
Adapter when docking the device into the Rugged Communications and Charging Cradle.
1.
Open the access cover.
2.
If installing the Rugged IO Adapter, pull the access cover away from the device until it separates from the device.
117
Accessories
3.
Insert the Rugged IO Adapter onto the tablet.
1
2
Interface connector
Rugged IO adapter
4.
5.
6.
Remove the Rugged Frame and screws from box.
Separate the top and bottom sections of the Rugged Frame.
Place the bottom section on a flat surface.
1
2
7.
8.
Place the device into the bottom section.
Align the top section over the bottom section.
9.
Press the top section down onto the bottom section.
10.
Using a T6 Torx screwdriver, secure the Rugged Frame together using the provided M1.6 Torx screws.
118
Accessories
Figure 38 Secure 8 in.Rugged Frame
Figure 39 Secure 10 in. Rugged Frame
11.
Torque the screws to 12 N-cm.
119
Accessories
Expansion Back
The Expansion Backs provide data capture and or Power Pack slot for the device.
Installation
To install an Expansion Back:
CAUTION: Remove power before installing the Expansion Back.
1.
2.
Power off the device.
Remove battery cover and store in safe place.
3.
On 8.4 in. version only, remove rubber gasket.
1 Rubber gasket
1
120
Accessories
4. Align expansion back with device. Ensure that the power pack slot cover is aligned with the bottom of the device and the interface connector on expansion back aligns with interface connector on device.
1
1
2
2
Power pack slot cover
Interface connector
Figure 40 Align Expansion Back with 8 in. Configuration
1
1
2
2
Power pack slot cover
Interface connector
121
Accessories
5.
Using a T6 Torx screwdriver, secure expansion back to device using four screws. Torque to 14 n-cm.
1
1 Screws (4)
Replacement Hand Strap
To replace the hand strap:
1.
If the Power Pack is installed, remove the Power Pack.
2.
Rotate the disk so that the strap end without the eyelet is aligned with the Power Pack opening.
3.
Open both ends of the hand strap.
122
Accessories
4.
Pull the strap end without the eyelet through the slot on the Expansion Back.
5.
6.
7.
Rotate the disk 180°.
Slide the pad off the hand strap.
Pull the eyelet end through the slot on the Expansion Back.
8.
9.
Remove pad from new replacement hand strap.
Rotate the disk so that one of the slots is aligned with the Power Pack opening.
123
Accessories
10.
Feed the new hand strap through the slot at the Power Pack opening.
1
2
3
5
6
4
7
5
6
7
3
4
1
2
Eyelet
Hook material
Disk slot
Hook material
Disk slot
Hand strap disk
Power pack opening
11.
Slide pad onto hand strap with the stylus holder facing up.
124
Accessories
12.
Fold the eyelet end of the strap up and press hook and loop material together.
1
2
1
2
Pad
Stylus holder
13.
Rotate disk 180° so that the empty slot is aligned with the Power Pack opening.
14.
Feed strap through the slot.
125
Accessories
15.
Fold the end of the strap up and press hook and loop material together.
Attaching the Stylus to the Expansion Back
The Expansion Backs provide a holder for the stylus. To install the stylus onto the Expansion Back with th option tether:
1.
Insert one loop of the tether into the hole in the stylus end cap.
2.
Feed the other end of the tether through the loop.
3.
4.
5.
Pull the tether all the way through the loop.
Insert the loop of the tether through the eyelet on the hand strap of the Expansion Back.
Feed the stylus through the loop.
6.
Pull the stylus all the way through the loop.
126
Accessories
7.
Slide the stylus into the holder for storing the stylus.
Removal
To remove an Expansion Back:
CAUTION: Remove power before removing the Expansion Back.
1.
2.
Power off the device.
Using a T6 Torx screwdriver, remove four screws securing expansion back to device.
1
1 Screws (4)
127
3. Lift Expansion Back off device.
Accessories
4.
On 8 in. version only, replace rubber gasket removed during installation.
1
1 Rubber gasket
5.
Replace battery cover.
128
Accessories
6.
Carefully press down around the edge of the cover. Make sure that the cover is seated properly.
7.
Press the Power button to turn on the device.
129
Accessories
ET51 with Integrated Scanner Hand Strap
The ET51 Enterprise Tablet with Integrated Scanner comes with additional screws for securing the hand strap to the device.
Removing the Hand Strap
To remove the hand strap:
1.
Push the hand strap stud through the hole of the lower hand strap.
2.
Pull the lower hand strap from the upper hand strap.
3.
Remove the two screws and two washers securing the upper and lower hand strap to the device.
Installing the Hand Strap on the Back of the Device
To install the hand strap on the back of the device:
130
Accessories
1.
Align the upper and lower hand strap mounting holes with the screw holes on the device.
1 2
4
3
3
4
1
2
Washer
M2x6 Screw
Washer
M2.5x11 Screw
3.
4.
2.
Using a T6 Torx screwdriver, secure the upper and lower hand strap to the device using the one M2x6 screw, one M2.5x11 screw, and two washers.
Torque the screws to 20 N-cm (1.77 lb in).
Feed the lower half of the hand strap through the upper half.
5.
6.
Position the hand strap for the right fit.
Align the stud with a hole in the lower half.
131
Accessories
7.
Press the lower hand strap down until the stud comes through the hole.
Installing the Hand Strap on the Side of the Device
To install the hand strap on the side of the device:
1.
Align the upper and lower hand strap mounting holes with the screw holes on the device.
1
2
1
2
Washer
M2.5x11 screw
2.
3.
Using a T6 Torx screwdriver, secure the upper and lower hand strap to the device using the two
M2.5x11 screws, and two washers.
Torque the screws to 20 N-cm (1.77 lb in).
132
Accessories
4.
Feed the lower half of the hand strap through the upper half.
5.
6.
7.
Position the hand strap for the right fit.
Align the stud with a hole in the lower half.
Press the lower hand strap down until the stud comes through the hole.
133
Application Deployment
Security
The device implements a set of security policies that determine whether an application is allowed to run and, if allowed, with what level of trust. To develop an application, you must know the security configuration of the device, and how to sign an application with the appropriate certificate to allow the application to run (and to run with the needed level of trust).
NOTE: Ensure the date is set correctly before installing certificates or when accessing secure web sites.
Secure Certificates
If the VPN or Wi-Fi networks rely on secure certificates, obtain the certificates and store them in the device’s secure credential storage, before configuring access to the VPN or Wi-Fi networks.
If downloading the certificates from a web site, set a password for the credential storage. The device supports X.509 certificates saved in PKCS#12 key store files with a .p12 extension (if key store has a .pfx or other extension, change to .p12).
The device also installs any accompanying private key or certificate authority certificates contained in the key store.
Installing a Secure Certificate
To install a secure certificate:
1.
Copy the certificate from the host computer to the root of the microSD card or the device’s internal memory. See
for information about connecting the device to a host computer and copying files.
2.
3.
4.
5.
6.
7.
8.
Go to Settings .
Touch Security > Advanced > Encryption & credentials .
Touch Install a certificate .
Navigate to the location of the certificate file.
Touch the filename of the certificate to install.
If prompted, enter the password for credential storage. If a password has not been set for the credential storage, enter a password for it twice and then touch OK .
If prompted, enter the certificate’s password and touch OK .
134
Application Deployment
9.
Enter a name for the certificate and in the Credential use drop-down, select VPN and apps or Wi-Fi .
10.
Touch OK .
The certificate can now be used when connecting to a secure network. For security, the certificate is deleted from the microSD card or internal memory.
Configuring Credential Storage Settings
1.
2.
Go to Settings .
Touch Security > Encryption & credentials .
• Trusted credentials - Touch to display the trusted system and user credentials.
• User credentials - Touch to display user credentials.
• Install from storage - Touch to install a secure certificate from the internal storage.
• Clear credentials - Deletes all secure certificates and related credentials.
Development Tools
Development tools for Android include Android Studio, EMDK for Android, and StageNow.
Android Application Development
Development Workstation
Android development tools are available at developer.android.com
.
To start developing applications for the device, download Android Studio. Development can take place on a Microsoft® Windows®, Mac® OS X®, or Linux® operating system.
Applications are written in Java or Kotlin, but compiled and executed in the Dalvik virtual machine. Once the Java code is compiled cleanly, the developer tools make sure the application is packaged properly, including the AndroidManifest.xml file.
Android Studio contains a full featured IDE as well as SDK components required to develop Android applications.
Enabling Developer Options
The Developer options screen sets development related settings. By default, the Developer Options are hidden.
1.
2.
3.
4.
5.
6.
7.
Go to Settings .
Touch About phone .
Scroll down to Build number .
Tap Build number seven times. The message You are now a developer!
appears.
Touch the Back button.
Touch System > Advanced > Developer options .
Slide the USB debugging switch to the ON position.
135
Application Deployment
EMDK for Android
EMDK for Android provides developers with tools to create business applications for enterprise mobile devices. It is designed for use with Google's Android Studio and includes Android class libraries such as
Barcode, sample applications with source code, and the associated documentation.
EMDK for Android allows applications to take full advantage of the capabilities that Zebra devices have to offer. It embeds Profile Manager technology within Android Studio IDE, providing a GUI-based development tool designed specifically for Zebra devices. This allows fewer lines of code, resulting in reduced development time, effort, and errors.
For more information go to: techdocs.zebra.com
.
StageNow
StageNow is Zebra's next-generation Android Staging Solution built on the MX platform. It allows quick and easy creation of device profiles, and can deploy to devices simply by scanning a barcode, reading a tag, or playing an audio file.
The StageNow Staging Solution includes the following components:
• The StageNow Workstation tool installs on the staging workstation (host computer) and lets the administrator easily create staging profiles for configuring device components, and perform other staging actions such as checking the condition of a target device to determine suitability for software upgrades or other activities. The StageNow Workstation stores profiles and other created content for later use.
• The StageNow Client resides on the device and provides a user interface for the staging operator to initiate staging. The operator uses one or more of the desired staging methods (print and scan a barcode, read an NFC tag or play an audio file) to deliver staging material to the device.
For more information go to: techdocs.zebra.com
.
GMS Restricted
GMS Restricted mode deactivates Google Mobile Services (GMS). All GMS apps are disabled on the device and communication with Google (analytics data collection and location services) is disabled.
Use StageNow to disable or enable GMS Restricted mode. After a device is in GMS Restricted mode, enable and disable individual GMS apps and services using StageNow. To ensure GMS Restricted mode persists after an Enterprise Reset, use the Persist Manager option in StageNow. For more information on
StageNow, refer to techdocs.zebra.com
.
ADB USB Setup
To use the ADB, install the USB driver. This assumes that the development SDK has been installed on the host computer. Go to developer.android.com/sdk/index.html
for details on setting up the development
SDK.
ADB driver for Windows and Linux are available on the Zebra Support Central web site at zebra.com/support . Download the ADB and USB Driver Setup package. Follow the instructions with the package to install the ADB and USB drivers for Windows and Linux.
Enabling USB Debugging
By default, USB debugging is disabled.
136
Application Deployment
1.
2.
3.
4.
Go to Settings .
Touch About phone .
Scroll down to Build number .
Tap Build number seven times. The message You are now a developer!
appears.
Touch the Back button.
5.
6.
7.
8.
Touch System > Advanced > Developer options .
Slide the USB debugging switch to the ON position.
Touch OK .
Connect the device to the host computer using a USB-C Cable.
9.
The Allow USB debugging?
dialog box appears on the device.
10.
On the device, touch OK .
11.
On the host computer, navigate to the platform-tools folder.
12.
Open a command prompt window and use the adb command: adb devices
The following displays:
List of devices attached
XXXXXXXXXXXXXXX device (where XXXXXXXXXXXXXXX is the device number).
NOTE: If device number does not appear, ensure that ADB drivers are installed properly.
13.
Touch the Home button.
Entering Android Recovery Manually
Many of the update methods discussed in this section require putting the device into Android Recovery mode. If you are unable to enter Android Recovery mode through adb commands, use the following steps to manually enter Android Recovery mode.
1.
Press and hold the Power button until the menu appears.
2.
3.
Touch Restart .
Press and hold the volume up button until the device vibrates. The System Recovery screen appears.
Application Installation
After an application is developed, install the application onto the device using one of the following methods:
• USB connection, see
Installing Applications Using the USB Connection on page 138 .
• Android Debug Bridge, see
Installing Applications Using the Android Debug Bridge on page 138 .
•
•
microSD Card, see Installing Applications Using a microSD Card on page 140
.
137
Application Deployment
• Mobile device management (MDM) platforms that have application provisioning. Refer to the MDM software documentation for details.
Installing Applications Using the USB Connection
CAUTION: When connecting the device to a host computer and mounting the microSD card, follow the host computer’s instructions for connecting and disconnecting USB devices, to avoid damaging or corrupting files.
NOTE: Not supported on the ET51 Enterprise Tablet with Integrated Scanner.
3.
4.
1.
2.
5.
Connect the device to a host computer using the USB-C cable.
Pull down the Notification panel and touch Charging this device via USB .
Touch File Transfer .
On the host computer, open a file manager application.
On the host computer, copy the application .apk file from the host computer to the device.
CAUTION: Carefully follow the host computer’s instructions to unmount the microSD card and disconnect
USB devices correctly to avoid losing information.
6.
Disconnect the device from the host computer.
7.
Swipe the screen up and select to view files on the microSD card or Internal Storage.
8.
Locate the application .apk file.
9.
Touch the application file.
10.
Touch Continue to install the app or Cancel to stop the installation.
11.
To confirm installation and accept what the application affects, touch Install otherwise touch Cancel .
12.
Touch Open to open the application or Done to exit the installation process. The application appears in the App list.
Installing Applications Using the Android Debug Bridge
Use ADB commands to install an application onto the device.
CAUTION: When connecting the device to a host computer and mounting its microSD card, follow the host computer’s instructions for connecting and disconnecting USB devices, to avoid damaging or corrupting files.
NOTE: Not supported on the ET51 Enterprise Tablet with Integrated Scanner.
3.
4.
1.
2.
5.
6.
Ensure that the ADB drivers are installed on the host computer. See
.
Connect the device to a host computer using USB. See USB Communication on page 32 .
Enable Developer options. For more information see Enabling USB Debugging on page 136 .
Go to Settings .
Touch System > Advanced > Developer options .
Slide the switch to the ON position.
138
Application Deployment
8.
9.
7.
Touch USB Debugging . A check appears in the check box. The Allow USB debugging?
dialog box appears.
Touch OK .
On the host computer, open a command prompt window and use the adb command: adb install <application> where: <application> = the path and filename of the apk file.
10.
Disconnect the device from the host computer. See
.
Installing Applications Using the Wireless Android Debug Bridge
Use ADB commands to install an application onto the device.
IMPORTANT: Ensure that the latest adb files are installed on the host computer.
NOTE: The device and the host computer must be on the same wireless network.
1.
2.
3.
4.
5.
6.
Go to Settings .
Touch System > Advanced > Developer options .
Slide the switch to the ON position.
Slide the USB debugging switch to the ON position.
Slide the Wireless debugging switch to the ON position.
If the device and host computer are connected for the first time, the Allow wireless debugging on this network?
dialog box with the Always allow from this network check box displays. Select the check box, if required.
7.
8.
9.
Touch ALLOW .
Touch Wireless debugging .
Touch Pair with pairing code .
The Pair with device dialog box displays.
10.
On the host computer, navigate to the platform-tools folder and open a command prompt window.
11.
Type adb pair XX.XX.XX.XX.XXXXX
.
where XX.XX.XX.XX:XXXXX is the IP address and port number from the Pair with device dialog box.
12.
Type: adb connect XX.XX.XX.XX.XXXXX
13.
Press Enter.
14.
Type the pairing code from the Pair with device dialog box.
15.
Press Enter.
16.
Type adb connect .
The device is now connected to the host computer.
139
Application Deployment
17.
On the host computer, use the adb command: adb devices
The following displays:
List of devices attached
XXXXXXXXXXXXXXX device (where XXXXXXXXXXXXXXX is the device number).
NOTE: If device number does not appear, ensure that ADB drivers are installed properly.
18.
On the host computer, open a command prompt window and use the adb command: adb install <application> where: <application> = the path and filename of the apk file.
19.
On the host computer, type adb disconnect .
Installing Applications Using a microSD Card
3.
6.
7.
4.
5.
8.
9.
CAUTION: When connecting the device to a host computer and mounting its microSD card, follow the host computer’s instructions for connecting and disconnecting USB devices, to avoid damaging or corrupting files.
1.
Copy the apk file to the root of the microSD card.
•
Copy the apk file to a microSD card using a host computer (see USB Communication
for more information), and then install the microSD card into the device (see Replacing the microSD Card for more information).
2.
• Connect the device with a microSD card already installed to the host computer, and copy apk file to
the microSD card. See USB Communication
for more information. Disconnect the device from the host computer.
Press and hold the Power button to turn on the device.
Swipe the screen up and select to view files on the microSD card.
Touch > SD card .
Locate the application .apk file.
Touch the application file.
Touch Continue . to install the app or Cancel to stop the installation.
To confirm installation and accept what the application affects, touch Install otherwise touch Cancel .
Touch Open to open the application or Done to exit the installation process. The application appears in the App list.
Uninstalling an Application
3.
4.
1.
2.
5.
Go to Settings .
Touch Apps & notifications .
Touch See all apps to view all apps in the list.
Scroll through the list to the app.
Touch the app. The App info screen appears.
140
Application Deployment
6.
7.
Touch Uninstall .
Touch OK to confirm.
Performing a System Update
CAUTION: These update procedures are only for updating an Android tablet (ET51CE, ET51CT, ET56DE,
ET56DT). Do not attempt to update a Windows Tablet (ET51AE, ET56BE, ET51AT, ET56BT) with Android software.
System Update packages can contain either partial or complete updates for the operating system. Zebra distributes the System Update packages on the Zebra Support & Downloads web site. Perform a system update using ADB.
Downloading the System Update Package
1.
2.
Go to the Zebra Support & Downloads web site, zebra.com/support .
Download the appropriate System Update package to a host computer.
Performing a System Update Using microSD Card
It is strongly recommended that prior to use, you must format the microSD card on the device.
1.
Copy the System Update zip file to the root of the microSD card.
2.
•
Copy the zip file to a microSD card using a host computer (see USB Communication
for more information), and then installing the microSD card into the device (see Replacing the microSD Card for more information).
• Connect the device with a microSD card already installed to the host computer, and copy zip file to
the microSD card. See USB Communication
for more information. Disconnect the device from the host computer.
Press and hold the Power button until the menu appears.
3.
4.
5.
6.
7.
8.
9.
Touch Restart .
Press and hold the volume up button until the device vibrates. The System Recovery screen appears.
Press the Volume Up and Volume Down buttons to navigate to Apply upgrade from SD card .
Press the Power button.
Press the Volume Up and Volume Down buttons to navigate to the System Update file.
Press the Power button. The System Update installs and then the device returns to the Recovery screen.
Press the Power button to reboot the device.
Performing a System Update Using ADB
NOTE: Not supported on the ET51 Enterprise Tablet with Integrated Scanner.
1.
2.
3.
Ensure that the ADB drivers are installed on the host computer. See
.
Connect the device to a host computer using USB. See USB Communication on page 32 .
Go to Settings .
141
Application Deployment
7.
8.
4.
5.
6.
Touch System > Advanced > Developer options .
Slide the switch to the ON position.
Touch USB Debugging . A check appears in the check box. The Allow USB debugging?
dialog box appears.
Touch OK .
On the host computer, open a command prompt window and use the adb command: adb devices
The following displays:
List of devices attached
XXXXXXXXXXXXXXX device (where XXXXXXXXXXXXXXX is the device number).
NOTE: If device number does not appear, ensure that ADB drivers are installed properly.
9.
Type: adb reboot recovery
If you are not able to enter Android Recovery mode through the adb command, go to Entering Android
Recovery Manually on page 137 .
10.
Press Enter. The System Recovery screen appears on the device.
11.
Press the Volume Up and Volume Down buttons to navigate to Apply upgrade from ADB .
12.
Press the Power button.
13.
On the host computer command prompt window type: adb sideload <file> where: <file> = the path and filename of the zip file.
14.
Press Enter. The System Update installs (progress appears as percentage in the Command Prompt window) and then the System Recovery screen appears on the device.
15.
Press the Power button to reboot the device.
Performing a System Update Using Wireless ADB
IMPORTANT: Ensure that the latest adb files are installed on the host computer.
NOTE: The device and the host computer must be on the same wireless network.
3.
4.
1.
2.
5.
6.
Go to Settings .
Touch System > Advanced > Developer options .
Slide the switch to the ON position.
Slide the USB debugging switch to the ON position.
Slide the Wireless debugging switch to the ON position.
If the device and host computer are connected for the first time, the Allow wireless debugging on this network?
dialog box with the Always allow from this network check box displays. Select the check box, if required.
142
Application Deployment
7.
8.
9.
Touch ALLOW .
Touch Wireless debugging .
Touch Pair with pairing code .
The Pair with device dialog box displays.
10.
On the host computer, navigate to the platform-tools folder and open a command prompt window.
11.
Type adb pair XX.XX.XX.XX.XXXXX
.
where XX.XX.XX.XX:XXXXX is the IP address and port number from the Pair with device dialog box.
12.
Type: adb connect XX.XX.XX.XX.XXXXX
13.
Press Enter.
14.
Type the pairing code from the Pair with device dialog box.
15.
Press Enter.
16.
Type adb connect .
The device is now connected to the host computer.
17.
On the host computer, use the adb command: adb devices
The following displays:
List of devices attached
XXXXXXXXXXXXXXX device (where XXXXXXXXXXXXXXX is the device number).
NOTE: If device number does not appear, ensure that ADB drivers are installed properly.
18.
Type: adb reboot recovery
If you are not able to enter Android Recovery mode through the adb command, go to Entering Android
Recovery Manually on page 137 .
19.
Press Enter. The System Recovery screen appears on the device.
20.
Press the Volume Up and Volume Down buttons to navigate to Apply upgrade from ADB .
21.
Press the Power button.
22.
On the host computer command prompt window type: adb sideload <file> where: <file> = the path and filename of the zip file.
23.
Press Enter. The System Update installs (progress appears as percentage in the Command Prompt window) and then the System Recovery screen appears on the device.
24.
Press the Power button to reboot the device.
25.
On the host computer, type adb disconnect .
Verifying System Update Installation
1.
2.
Go to Settings .
Touch About phone .
143
Application Deployment
3.
4.
Scroll down to Build number .
Ensure that the build number matches the new system update package file number.
Enterprise Reset
An Enterprise Reset erases all user data in the /data partition, including data in the primary storage locations ( /sdcard and emulated storage).
Before performing an Enterprise Reset, provision all necessary configuration files and restore after the reset.
Perform Enterprise Reset using device settings, or ADB.
Performing an Enterprise Reset From Device Settings
1.
2.
3.
Go to Settings .
Touch System > Reset options > Erase all data (enterprise reset) .
Touch Erase all data twice to confirm the Enterprise Reset.
Downloading the Enterprise Reset Package
1.
2.
Go to the Zebra Support & Downloads web site, zebra.com/support .
Download the Enterprise Reset file to a host computer.
Performing an Enterprise Reset Using microSD Card
1.
6.
7.
8.
4.
5.
2.
3.
9.
Copy the Enterprise Reset zip file to the root of the microSD card.
•
Copy the zip file to a microSD card using a host computer (see USB Communication
for more information) and then installing the microSD card into the device (see Replacing the microSD Card for more information).
• Connect the device with a microSD card already installed to the host computer and copy zip file to
the microSD card. See USB Communication
for more information. Disconnect the device from the host computer.
Press and hold the Power button until the menu appears.
Touch Restart .
Press and hold the volume up button until the device vibrates. The System Recovery screen appears.
Press the Volume Up and Volume Down buttons to navigate to Apply upgrade from SD card .
Press the Power button.
Press the Volume Up and Volume Down buttons to navigate to the Enterprise Reset file.
Press the Power button. The Enterprise Reset occurs and then the device returns to the Recovery screen.
Press the Power button to reboot the device.
Performing an Enterprise Reset Using ADB
1.
Connect the device to a host computer using a micro USB-C cable.
144
Application Deployment
6.
7.
4.
5.
2.
3.
Go to Settings .
Touch System > Advanced > Developer options .
Slide the switch to the ON position.
Touch USB Debugging . A check appears in the check box. The Allow USB debugging?
dialog box appears.
Touch OK .
On the host computer, open a command prompt window and type: adb devices .
The following displays:
List of devices attached
XXXXXXXXXXXXXXX device (where XXXXXXXXXXXXXXX is the device number).
NOTE: If device number does not appear, ensure that ADB drivers are installed properly.
8.
Type: adb reboot recovery
If you are not able to enter Android Recovery mode through the adb command, go to Entering Android
Recovery Manually on page 137 .
9.
Press Enter. The System Recovery screen appears on the device.
10.
Press the Volume Up and Volume Down buttons to navigate to Apply upgrade from ADB .
11.
Press the Power button.
12.
On the host computer command prompt window type: adb sideload <file> where: <file> = the path and filename of the zip file.
13.
Press Enter. The Enterprise Reset package installs and then the System Recovery screen appears on the device.
14.
Press the Power button to reboot the device.
Performing an Enterprise Reset Using Wireless ADB
IMPORTANT: Ensure that the latest adb files are installed on the host computer.
NOTE: The device and the host computer must be on the same wireless network.
3.
4.
1.
2.
5.
Go to Settings .
Touch System > Advanced > Developer options .
Slide the switch to the ON position.
Slide the USB debugging switch to the ON position.
Slide the Wireless debugging switch to the ON position.
145
Application Deployment
6.
If the device and host computer are connected for the first time, the Allow wireless debugging on this network?
dialog box with the Always allow from this network check box displays. Select the check box, if required.
7.
8.
9.
Touch ALLOW .
Touch Wireless debugging .
Touch Pair with pairing code .
The Pair with device dialog box displays.
10.
On the host computer, navigate to the platform-tools folder and open a command prompt window.
11.
Type adb pair XX.XX.XX.XX.XXXXX
.
where XX.XX.XX.XX:XXXXX is the IP address and port number from the Pair with device dialog box.
12.
Type: adb connect XX.XX.XX.XX.XXXXX
13.
Press Enter.
14.
Type the pairing code from the Pair with device dialog box.
15.
Press Enter.
16.
Type adb connect .
The device is now connected to the host computer.
17.
On the host computer, open a command prompt window and type: adb devices .
The following displays:
List of devices attached
XXXXXXXXXXXXXXX device (where XXXXXXXXXXXXXXX is the device number).
NOTE: If device number does not appear, ensure that ADB drivers are installed properly.
18.
Type: adb reboot recovery
If you are not able to enter Android Recovery mode through the adb command, go to Entering Android
Recovery Manually on page 137 .
19.
Press Enter. The System Recovery screen appears on the device.
20.
Press the Volume Up and Volume Down buttons to navigate to Apply upgrade from ADB .
21.
Press the Power button.
22.
On the host computer command prompt window type: adb sideload <file> where: <file> = the path and filename of the zip file.
23.
Press Enter. The Enterprise Reset package installs and then the System Recovery screen appears on the device.
24.
Press the Power button to reboot the device.
25.
On the host computer, type adb disconnect .
146
Application Deployment
Performing a Factory Reset
A Factory Reset erases all data in the /data and /enterprise partitions in internal storage and clears all device settings. A Factory Reset returns the device to the last installed operating system image. To revert
for more information.
Downloading the Factory Reset Package
To download the Factory Reset package:
1.
Go to the Zebra Support & Downloads web site, zebra.com/support .
2.
Download the appropriate Factory Reset file to a host computer.
Performing a Factory Reset Using microSD Card
8.
9.
6.
7.
4.
5.
2.
3.
1.
Copy the Factory Reset zip file to the root of the microSD card.
•
Copy the zip file to a microSD card using a host computer (see USB Communication
for more information) and then installing the microSD card into the device (see Replacing the microSD Card for more information).
• Connect the device with a microSD card already installed to the host computer and copy zip file to
the microSD card. See USB Communication
for more information. Disconnect the device from the host computer.
Press and hold the Power button until the menu appears.
Touch Restart .
Press and hold the Volume Up button until the device vibrates. The System Recovery screen appears.
Press the Volume Up and Volume Down buttons to navigate to Apply upgrade from SD card .
Press the Power button.
Use the Volume Up and Volume Down buttons to navigate to the Factory Reset file.
Press the Power button. The Factory Reset occurs and then the device returns to the Recovery screen.
Press the Power button to reboot the device.
Performing a Factory Reset Using ADB
To perform an Factory Reset using ADB:
1.
Connect the device to a host computer using a USB-C cable.
2.
3.
4.
5.
6.
Go to Settings .
Touch System > Advanced > Developer options .
Slide the switch to the ON position.
Touch USB Debugging . A check appears in the check box. The Allow USB debugging?
dialog box appears.
Touch OK .
147
Application Deployment
7.
On the host computer, open a command prompt window and type: adb devices .
The following displays:
List of devices attached
XXXXXXXXXXXXXXX device (where XXXXXXXXXXXXXXX is the device number).
NOTE: If device number does not appear, ensure that ADB drivers are installed properly.
8.
Type: adb reboot recovery
If you are not able to enter Android Recovery mode through the adb command, go to Entering Android
Recovery Manually on page 137 .
9.
Press Enter. The System Recovery screen appears on the device.
10.
Press the Volume Up and Volume Down buttons to navigate to Apply upgrade from ADB .
11.
Press the Power button.
12.
On the host computer command prompt window type: adb sideload <file> where: <file> = the path and filename of the zip file.
13.
Press Enter. The Factory Reset package installs and then the System Recovery screen appears on the device.
14.
Press the Power button to reboot the device.
Performing a Factory Reset Using Wireless ADB
IMPORTANT: Ensure that the latest adb files are installed on the host computer.
NOTE: The device and the host computer must be on the same wireless network.
1.
2.
3.
4.
5.
6.
Go to Settings .
Touch System > Advanced > Developer options .
Slide the switch to the ON position.
Slide the USB debugging switch to the ON position.
Slide the Wireless debugging switch to the ON position.
If the device and host computer are connected for the first time, the Allow wireless debugging on this network?
dialog box with the Always allow from this network check box displays. Select the check box, if required.
7.
8.
9.
Touch ALLOW .
Touch Wireless debugging .
Touch Pair with pairing code .
The Pair with device dialog box displays.
10.
On the host computer, navigate to the platform-tools folder and open a command prompt window.
148
Application Deployment
11.
Type adb pair XX.XX.XX.XX.XXXXX
.
where XX.XX.XX.XX:XXXXX is the IP address and port number from the Pair with device dialog box.
12.
Type: adb connect XX.XX.XX.XX.XXXXX
13.
Press Enter.
14.
Type the pairing code from the Pair with device dialog box.
15.
Press Enter.
16.
Type adb connect .
The device is now connected to the host computer.
17.
On the host computer, open a command prompt window and type: adb devices .
The following displays:
List of devices attached
XXXXXXXXXXXXXXX device (where XXXXXXXXXXXXXXX is the device number).
NOTE: If device number does not appear, ensure that ADB drivers are installed properly.
18.
Type: adb reboot recovery
If you are not able to enter Android Recovery mode through the adb command, go to Entering Android
Recovery Manually on page 137 .
19.
Press Enter. The System Recovery screen appears on the device.
20.
Press the Volume Up and Volume Down buttons to navigate to Apply upgrade from ADB .
21.
Press the Power button.
22.
On the host computer command prompt window type: adb sideload <file> where: <file> = the path and filename of the zip file.
23.
Press Enter. The Factory Reset package installs and then the System Recovery screen appears on the device.
24.
Press the Power button to reboot the device.
25.
On the host computer, type adb disconnect .
Storage
The device contains the following types of file storage:
• Random Access Memory (RAM)
• Internal storage
• Enterprise folder.
149
Application Deployment
Random Access Memory
Executing programs use RAM to store data. Data stored in RAM is lost upon a reset. The operating system manages how applications use RAM. It only allows applications and component processes and services to use RAM when required. It may cache recently used processes in RAM, so they restart more quickly when opened again, but it will erase the cache if it needs the RAM for new activities.
The screen displays the amount of used and free RAM.
• Performance - Indicates memory performance.
• Total memory - Indicates the total amount of RAM available.
• Average used (%) - Indicates the average amount of memory (as a percentage) used during the period of time selected (default - 3 hours).
• Free - Indicates the total amount of unused RAM.
• Memory used by apps - Touch to view RAM usage by individual apps.
Viewing Memory
1.
2.
Go to Settings .
Touch System > Advanced > Developer options > Memory .
Internal Storage
The device has internal storage. The internal storage content can be viewed and files copied to and from when the device is connected to a host computer. Some applications are designed to be stored on the internal storage rather than in internal memory.
Viewing Internal Storage
1.
2.
Go to Settings .
Touch Storage .
If the device has removable storage installed, touch Internal shared storage to display a the amount of internal storage used by apps, photos, videos, audio and other files.
External Storage
The device can have a removable microSD card. The microSD card content can be viewed and files copied to and from when the device is connected to a host computer.
Viewing External Storage
1.
2.
Go to Settings .
Touch Storage .
Portable storage displays the total amount of space on the installed microSD card and the amount used.
To unmount the microSD card, touch .
Formatting a microSD Card
1.
Touch SD card .
150
Application Deployment
4.
5.
2.
3.
Touch > Storage settings .
Touch Format .
Touch ERASE & FORMAT .
Touch DONE .
Formatting a microSD Card as Internal Memory
4.
5.
2.
3.
You can format a microSD card as internal memory to increase the actual amount of the device’s internal memory. Once formatted, the microSD card can only be read by this device.
1.
Touch SD card .
Touch > Storage settings .
Touch Format as internal .
Touch ERASE & FORMAT .
Touch DONE .
Enterprise Folder
The Enterprise folder (within internal flash) is a super-persistent storage that is persistent after a reset and an Enterprise Reset. The Enterprise folder is erased during a Factory Reset. The Enterprise folder is used for deployment and device-unique data. The Enterprise folder is approximately 128 MB (formatted).
Applications can persist data after an Enterprise Reset by saving data to the enterprise/user folder. The folder is ext4 formatted and is only accessible from a host computer using ADB or from an MDM.
Managing Apps
4.
5.
Apps use two kinds of memory: storage memory and RAM. Apps use storage memory for themselves and any files, settings, and other data they use. They also use RAM when they are running.
1.
2.
3.
Go to Settings .
Touch Apps & notifications .
Touch See all XX apps to view all apps on the device.
Touch > Show system to include system processes in the list.
Touch an app, process, or service in the list to open a screen with details about it and, depending on the item, to change its settings, permissions, notifications and to force stop or uninstall it.
App Details
Apps have different kinds of information and controls.
• Force stop - Stop an app.
• Disable - Disable an app.
• Uninstall - Remove the app and all of its data and settings from the device. See
Application on page 140 for information about uninstalling apps.
• Notifications - Set the app notification settings.
• Permissions - Lists the areas on the device that the app has access to.
• Storage & cache - Lists how much information is stored, and includes buttons for clearing it.
151
Application Deployment
• Mobile data & Wi-Fi - Provides information about data consumed by an app.
• Advanced
• Screen time - Displays the amount of time the app has displayed on the screen.
• Battery - Lists the amount of computing power used by the app.
• Open by default - If you have configured an app to launch certain file types by default, you can clear that setting here.
• Display over other apps - allows an app to display on top of other apps.
• App details - Provides a link to additional app details on the Play store.
• Additional settings in the app - Opens settings in the app.
• Modify system settings - Allows an app to modify the system settings.
Managing Downloads
Files and apps downloaded using the Browser or Email are stored on the Internal storage in the Download directory. Use the Downloads app to view, open, or delete downloaded items.
1.
Swipe the screen up and touch .
2.
3.
Touch > Downloads .
Touch and hold an item, select items to delete and touch . The item is deleted from the device.
152
Maintenance and
Troubleshooting
Introduction
This chapter includes instructions on cleaning and storing the tablet, battery maintenance and provides troubleshooting solutions for potential problems during tablet operations.
Maintaining the Device
For trouble-free service, observe the following tips when using the device:
• To avoid scratching the screen, use the supplied stylus or plastic-tipped pens intended for use with a touch-sensitive screen. Never use an actual pen or pencil or other sharp object on the surface of the device screen.
• The touch-sensitive screen of the device is glass. Do not drop the device or subject it to strong impact.
• Protect the device from temperature extremes. Do not leave it on the dashboard of a car on a hot day, and keep it away from heat sources.
• Do not store the device in any location that is dusty, damp, or wet.
• Use a soft lens cloth to clean the device. If the surface of the device screen becomes soiled, clean it with a soft cloth moistened with an approved cleanser. For a list of approved cleansers, see Approved
Cleanser Active Ingredients.
• Periodically replace the rechargeable battery to ensure maximum battery life and product performance.
Battery life depends on individual usage patterns.
Battery Safety Guidelines
• The area in which the units are charged should be clear of debris and combustible materials or chemicals. Particular care should be taken where the device is charged in a non commercial environment.
• Follow battery usage, storage, and charging guidelines found in this guide.
• Improper battery use may result in a fire, explosion, or other hazard.
• To charge the mobile device battery, the ambient battery and charger temperatures must be between
+32ºF and +104ºF (0ºC and +40ºC).
• Do not use incompatible batteries and chargers, including non-Zebra batteries and chargers. Use of an incompatible battery or charger may present a risk of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a battery or a charger, contact the Global Customer
Support Center.
153
Maintenance and Troubleshooting
• For devices that utilize a USB port as a charging source, the device shall only be connected to products that bear the USB-IF logo or have completed the USB-IF compliance program.
• Do not disassemble or open, crush, bend or deform, puncture, or shred the battery.
• Severe impact from dropping any battery-operated device on a hard surface could cause the battery to overheat.
• Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals.
• Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water or other liquids, or expose to fire, explosion, or other hazard.
• Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or near a radiator or other heat source. Do not place battery into a microwave oven or dryer.
• Battery usage by children should be supervised.
• Please follow local regulations to properly dispose of used re-chargeable batteries.
• Do not dispose of batteries in fire.
• In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with water for 15 minutes, and seek medical advice.
• If you suspect damage to your equipment or battery, contact Customer Support to arrange for inspection.
Cleaning Instructions
CAUTION: Always wear eye protection.
Read warning label on alcohol product before using.
If you have to use any other solution for medical reasons please contact the Global Customer Support
Center for more information.
WARNING: Avoid exposing this product to contact with hot oil or other flammable liquids. If such exposure occurs, unplug the device and clean the product immediately in accordance with these guidelines.
Approved Cleanser Active Ingredients
100% of the active ingredients in any cleaner must consist of one or some combination of the following: isopropyl alcohol, bleach/sodium hypochlorite 1 (see important note below) , or mild dish soap.
IMPORTANT: Use pre-moistened wipes and do not allow liquid cleaner to pool.
1 When using sodium hypochlorite (bleach) based products, always follow the manufacturer’s recommended instructions: use gloves during application and remove the residue afterwards with a damp alcohol cloth or a cotton swab to avoid prolonged skin contact while handling the device.
Due to the powerful oxidizing nature of sodium hypochlorite, the metal surfaces on the device are prone to oxidation (corrosion) when exposed to this chemical in the liquid form (including wipes). In the event that these type of disinfectants come in contact with metal on the device, prompt removal with an alcohol-dampened cloth or cotton swab after the cleaning step is critical.
154
Maintenance and Troubleshooting
Harmful Ingredients
The following chemicals are known to damage the plastics on the device and should not come in contact with the device: acetone; ketones; ethers; aromatic and chlorinated hydrocarbons; aqueous or alcoholic alkaline solutions; ethanolamine; toluene; trichloroethylene; benzene; carbolic acid and TB-lysoform.
Many vinyl gloves contain phthalate additives, which are often not recommended for medical use and are known to be harmful to the housing of the device.
Device Cleaning Instructions
Do not apply liquid directly to the device. Dampen a soft cloth or use pre-moistened wipes. Do not wrap the device in the cloth or wipe, instead gently wipe the unit. Be careful not to let liquid pool around the display window or other places. Before use, allow the unit to air dry.
NOTE: For thorough cleaning, it is recommended to first remove all accessory attachments, such as hand straps or cradle cups, from the mobile device and to clean them separately.
Special Cleaning Notes
The device should not be handled while wearing vinyl gloves containing phthalates, or before hands are washed to remove contaminant residue after gloves are removed.
If products containing any of the harmful ingredients listed above are used prior to handling the device, such as hand sanitizer that contain ethanolamine, hands must be completely dry before handling the device to prevent damage to the device.
IMPORTANT: If the battery connectors are exposed to cleaning agents, thoroughly wipe off as much of the chemical as possible and clean with an alcohol wipe. It is also recommended to install the battery in the terminal prior to cleaning and disinfecting the device to help minimize buildup on the connectors.
When using cleaning/disinfectant agents on the device, it is important to follow the directions prescribed by the cleaning/disinfectant agent manufacturer.
Cleaning Materials Required
• Alcohol wipes
• Lens tissue
• Cotton-tipped applicators
• Isopropyl alcohol
• Can of compressed air with a tube.
Cleaning Frequency
The cleaning frequency is at the customer’s discretion due to the varied environments in which the mobile devices are used and may be cleaned as frequently as required. When dirt is visible, it is recommended to clean the mobile device to avoid build up of particles which make the device more difficult to clean later on.
Cleaning Battery Connectors
To clean the battery connectors:
155
Maintenance and Troubleshooting
4.
5.
1.
2.
3.
6.
Remove the main battery from the mobile computer.
Dip the cotton portion of the cotton-tipped applicator in isopropyl alcohol.
To remove any grease or dirt, rub the cotton portion of the cotton-tipped applicator back-and-forth across the connectors on the battery and terminal sides. Do not leave any cotton residue on the connectors.
Repeat at least three times.
Use a dry cotton-tipped applicator and repeat steps 3 and 4. Do not leave any cotton residue on the connectors.
Inspect the area for any grease or dirt and repeat the cleaning process if necessary.
CAUTION: After cleaning the battery connectors with bleach-based chemicals, follow the Battery
Connector Cleaning instructions to remove bleach from the connectors.
156
Maintenance and Troubleshooting
Troubleshooting
Resetting the Device
There are two reset function, soft reset and hard reset.
Performing a Soft Reset
Perform a soft reset if the applications stop responding.
1.
Press and hold the Power button until the menu appears.
2.
Touch Restart.
The device reboots.
Performing a Hard Reset
CAUTION: Performing a hard reset with a microSD card installed in the device may cause damage or data corruption to the microSD card.
Perform a hard reset if the device stops responding.
1.
Simultaneously press the Power, PTT and Volume Up buttons for at least four seconds.
2.
When the screen turns off, release the buttons.
The device reboots.
Table 9 Troubleshooting the Tablet
Tablet does not turn on.
Problem Cause Solution
Battery not charged. Charge the battery in the tablet.
Battery not installed properly.
System crash.
Ensure battery is installed properly.
Battery did not charge. Battery failed.
If the tablet does not turn on, perform a hard reset.
See Performing a Hard Reset on page 157
.
Replace battery. If the tablet still does not operate, try
a hard reset. See Performing a Hard Reset on page 157
.
Insert the tablet into the cradle and begin charging.
The battery fully charges in approximately four hours.
Unable to connect to the wireless network.
Tablet removed from cradle before charging completed.
Ambient temperature of the cradle is too warm or too cold.
SIM card is valid.
Not within range of network.
device is in airplane mode.
The ambient temperature must be between 0°C and
40°C (32 °F and 104°F).
Ensure that the micro SIM card is valid and workable if using a mobile network.
Move within the network’s service range and the signal strength is good.
Ensure that device is not in Airplane mode.
157
Maintenance and Troubleshooting
Table 9 Troubleshooting the Tablet (Continued)
Problem
The multi-touch screen responds slowly or improperly.
Tablet turns itself off.
Cause
Finger or screen is wet.
Solution
Ensure that your hands are clean and dry when touching the screen. Restart the tablet to try again.
Tablet is inactive.
The tablet turns off after a period of inactivity. If the tablet is running on battery power.
Battery is depleted.
Place the tablet in the cradle to re-charge the battery.
The tablet’s battery is low and it powers down to protect memory content.
Place the tablet in a cradle to re-charge the battery.
Charge Only Cradle
Table 10 Troubleshooting the Charge only Cradle
Symptom
Battery is not charging.
Possible Cause
Tablet was removed from cradle or cradle was unplugged from AC power.
Battery is faulty.
Solution
Ensure cradle is receiving power. Ensure tablet is seated correctly. Confirm main battery is charging. The battery fully charges in approximately four hours.
The tablet is not fully seated in the cradle.
Ambient temperature of the cradle is too warm or too cold.
Verify that other batteries charge properly. If so, replace the faulty battery.
Remove and re-insert the tablet into the cradle, ensuring it is firmly seated.
Move the cradle to an area where the ambient temperature is between 0°C and 40°C (32°F and 104°F).
Communication and Charging Cradles
Table 11 Troubleshooting the Communication and Charging Cradles
Symptom
Battery is not charging.
Possible Cause
Tablet was removed from cradle or cradle was unplugged from AC power.
Battery is faulty.
Solution
Ensure cradle is receiving power. Ensure tablet is seated correctly. Confirm main battery is charging. The battery fully charges in approximately four hours.
The tablet is not fully seated in the cradle.
Ambient temperature of the cradle is too warm or too cold.
Verify that other batteries charge properly. If so, replace the faulty battery.
Remove and re-insert the tablet into the cradle, ensuring it is firmly seated.
Move the cradle to an area where the ambient temperature is between 0°C and 40°C (32°F and 104°F).
158
Maintenance and Troubleshooting
Table 11 Troubleshooting the Communication and Charging Cradles (Continued)
Symptom
During communication, no data transmits, or transmitted data was incomplete.
Tablet does not lock into cradle.
Possible Cause
Tablet removed from cradle during communications.
Incorrect cable configuration.
Access cover closed.
Tablet with Rugged
Frame and IO Adapter does not mate with
Communication and
Charging Cradle.
Solution
Replace tablet in cradle and retransmit.
Ensure that the correct cable configuration.
Open tablet access cover and re-insert tablet onto cradle.
Use Rugged Communication and Charging Cradle.
Expansion Backs
Table 12 Troubleshooting the Expansion Backs
Symptom
Aiming laser does not display when pressing trigger.
Possible Cause
On 8.4 in. tablet, did not remove rubber gasket during installation.
Tablet is in suspend mode.
Battery is low.
Solution
See system administrator to re-install Expansion Back.
Press power button to wake the tablet.
Laser comes on, but scanner does not decode the bar code.
Tablet is not programmed for the bar code.
Unreadable bar code.
If the scanner stops emitting a laser beam upon a scan button press, check the battery level. When the battery is low, the scanner shuts off before the tablet low battery condition notification. Note: If the scanner is still not reading bar codes, contact system administrator.
Ensure the application is programmed to read the type of bar code being scanned. Contact system administrator.
Check the symbol to ensure it is not defaced. Try scanning another bar code of the same type.
Move the tablet within proper scanning range.
Distance between exit window and bar code is incorrect.
Scanning application is not loaded.
Load a scanning application. See the system administrator.
159
Maintenance and Troubleshooting
4-Slot Charge Only Cradle
Table 13 Troubleshooting the 4-Slot Charge only Cradle
Symptom
Tablet battery is not charging.
Possible Cause
Tablet was removed from cradle or cradle was unplugged from AC power.
Battery is faulty.
Solution
Ensure cradle is receiving power. Ensure tablet is seated correctly. Confirm main battery is charging. The battery fully charges in approximately four hours.
The Tablet is not fully seated in the cradle.
Ambient temperature of the cradle is too warm or too cold.
Verify that other tablet batteries charge properly. If so, replace the faulty battery.
Remove and re-insert the tablet into the cradle, ensuring it is firmly seated. Ensure that an insert is not used with tablet with Rugged Frame. Ensure that an insert is used with tablet without Rugged Frame.
Move the cradle to an area where the ambient temperature is between 0°C and 40°C (32°F and 104°F).
Charging Adapter
Table 14 Troubleshooting the Charging Adapter
Symptom
Tablet battery is not charging.
Possible Cause
Tablet was removed from adapter or adapter was unplugged from AC power.
Battery is faulty.
Solution
Ensure adapter is receiving power. Ensure tablettablet is seated correctly. Confirm tablet is charging. The battery fully charges in approximately four hours.
The tablet is not fully seated in the adapter.
Ambient temperature of the adapter is too warm or too cold.
Verify that other tablet batteries charge properly. If so, replace the faulty battery.
Remove and re-insert the tablet into the adapter, ensuring it is firmly seated.
Move the adapter to an area where the ambient temperature is between 0°C and 40°C (32°F and 104°F).
160
Maintenance and Troubleshooting
4-Slot Battery Charger
Table 15 Troubleshooting the 4-Slot Battery Charger
Symptom
Power Pack
Charging LED does not light when inserted.
Power Pack is not charging.
Possible Cause
Power Pack is not correctly seated.
Power Pack was removed from charger or charger was unplugged from AC power.
Power Pack is faulty.
Solution
Remove and re-insert the spare battery into the charging slot, ensuring it is correctly seated.
Ensure charger is receiving power. Ensure Power Pack is seated correctly. Confirm Power Pack is charging. The
Power Pack fully charges in approximately four hours.
The Power Pack is not fully seated in the charger.
Ambient temperature of the charger is too warm or too cold.
Verify that other Power Pack charge properly. If so, replace the faulty Power Pack.
Remove and re-insert the Power Pack into the charger, ensuring it is firmly seated.
Move the charger to an area where the ambient temperature is between 0°C and 40°C (32°F and 104°F).
161
Specifications
Technical Specifications
For device technical specifications, go to zebra.com/et5x .
Need device camera decode symbologies.
Table 16 Expansion Back Supported Symbologies
1D
2D
Postal
Symbologies
Bookland EAN, Chinese 2 of 5, Codabar, Code 11, Code 128, Code 32, Code 39,
Code 93, Discrete 2 of 5, EAN-8, EAN-13, GS1-128, Interleaved 2 of 5, Inverse 1D,
ISBT-128, ISSN EAN, Korean 2 of 5, MSI, Matrix 2 of 5, Trioptic Code 39, UCC
Coupon Code, UPCA, UPCE, UPCE1.
Aztec, Aztec Inverse, Composite AB, Composite C, Data Matrix, Data Matrix Inverse,
Maxicode, Micro PDF417, Micro QR, PDF417, QR Code, QR Code Inverse, Han Xin,
Han Xin Inverse
Australian Postal, Japan Postal, UK Postal, US Planet, US Postnet, Netherlands KIX
Code, USPS 4CB/One Code/Intelligent Mail, UPU FICS Postal
SE4750 Expansion Back Decode Range
Table 17 SE4750 Decode Distances
Bar Code Type
3 mil Code 39
5 mil Code 128
5 mil PDF417
6.67mil PDF417
10 mil Data Matrix
2.8
2.3
3.0
2.2
2.4
6.2
8.7
8.1
10.6
10.6
* Limited by width of bar code in field of view.
Note: Photographic quality bar code at 18 o tilt pitch angle under 30 fcd ambient illumination.
162
Specifications
Table 17 SE4750 Decode Distances (Continued)
Bar Code Type
100% UPCA
15 mil Code 128
20.0 mil Code 39
1.6*
2.4*
1.6*
23.0
25.2
36.3
* Limited by width of bar code in field of view.
Note: Photographic quality bar code at 18 o tilt pitch angle under 30 fcd ambient illumination.
Integrated Scanner Decode Zones
Table 18 Integrated Scanner Decode Distances
Bar Code Type
4 mil Code 39
5 mil Code 128
5 mil Code 39
5 mil PDF417
3.3
2.3
2.0
3.1
8.8
8.2
11.625
8.4
10 mil Data Matrix
100% UPCA
2.9
1.8
10.1
26.0
20.0 mil Code 39 2.0
30.0
Note: Photographic quality bar code at 18 o tilt pitch angle under 30 fcd ambient illumination.
Accessory Specifications
Charge Only Cradle
Table 19 Charge Only Cradle Technical Specifications
Feature
Dimensions
Weight
Input Voltage
Power Consumption
Operating Temperature
Humidity
Electrostatic Discharge (ESD)
Description
Height: 7.9 cm (3.1 in.)
Width: 14.2 cm (5.6 in.)
Depth: 11.9 cm (4.7 in.)
423 g (14.9 oz)
12 VDC
60 watts
0°C to 40°C (32°F to 104°F)
10% to 90% non-condensing
+/- 8 kV air
+/- 4 kV contact
163
Specifications
Communication and Charging Cradle
Table 20 Communication and Charging Cradle Technical Specifications
Dimensions
Weight
Input Voltage
Feature
Power Consumption
Operating Temperature
Humidity
Electrostatic Discharge (ESD)
Description
Height: 7.9 cm (3.1 in.)
Width: 14.2 cm (5.6 in.)
Depth: 11.9 cm (4.7 in.)
629 g (22.2 oz)
12 VDC
60 watts
0°C to 40°C (32°F to 104°F)
5% to 90% non-condensing
+/- 8 kV air
+/- 4 kV contact
Rugged Communication and Charging Cradle
Table 21 Rugged Communication and Charging Cradle Technical Specifications
Dimensions
Weight
Feature
Input Voltage
Power Consumption
Operating Temperature
Humidity
Electrostatic Discharge (ESD)
Description
Height: 7.9 cm (3.1 in.)
Width: 14.2 cm (5.6 in.)
Depth: 11.9 cm (4.7 in.)
624 g (22.0 oz)
12 VDC
60 watts
0°C to 40°C (32°F to 104°F)
5% to 90% non-condensing
+/- 8 kV air
+/- 4 kV contact
164
Specifications
Expansion Backs
Table 22 8.4 in. Expansion Back Technical Specifications
Feature
Dimensions
Weight
Operating Temperature
Storage Temperature
Humidity
Drop
Electrostatic Discharge (ESD)
Height: 137 mm (5.4 in.)
Width: 157.5 mm (6.2 in.)
Depth: 54 mm (2.1 in.)
246 g (8.7 oz)
Description
0°C to 50°C (32°F to 122°F)
-20°C to 60°C (-40°F to 158°F)
5% to 95% non-condensing
1.2 m (4 ft) drop to plywood over concrete per MIL-STD 810G across operating temperatures with rugged frame.
+/- 8 kV air
+/- 4 kV contact
Table 23 8.4 in. SE4750 Expansion Back Technical Specifications
Dimensions
Weight
Operating Temperature
Storage Temperature
Humidity
Drop
Feature
Electrostatic Discharge (ESD)
Height: 137 mm (5.4 in.)
Width: 157.5 mm (6.2 in.)
Depth: 54 mm (2.1 in.)
273 g (9.6 oz)
Description
0°C to 50°C (32°F to 122°F)
-20°C to 60°C (-40°F to 158°F)
5% to 95% non-condensing
1.0 m (3.28 ft) drop to plywood over concrete per MIL-STD
810G across operating temperatures with rugged frame.
+/- 8 kV air
+/- 4 kV contact
Table 24 10.1 in. Expansion Back Technical Specifications
Feature
Dimensions
Weight
Operating Temperature
Storage Temperature
Height: 157.7 mm (6.2 in.)
Width: 184 mm (7.2 in.)
Depth: 54 mm (2.1 in.)
Description
307 g (10.8 oz)
0°C to 50°C (32°F to 122°F)
-20°C to 60°C (-40°F to 158°F)
165
Specifications
Table 24 10.1 in. Expansion Back Technical Specifications (Continued)
Humidity
Drop
Feature
Electrostatic Discharge (ESD)
Description
5% to 95% non-condensing
1.0 m (3.28 ft) drop to plywood over concrete per MIL-STD
810G across operating temperatures with rugged frame.
+/- 8 kV air
+/- 4 kV contact
Table 25 10.1 in. SE4750 Expansion Back Technical Specifications
Dimensions
Weight
Operating Temperature
Storage Temperature
Humidity
Drop
Feature
Electrostatic Discharge (ESD)
Description
Height: 157.7 mm (6.2 in.)
Width: 184 mm (7.2 in.)
Depth: 54 mm (2.1 in.)
336.5 g (11.9 oz)
0°C to 50°C (32°F to 122°F)
-20°C to 60°C (-40°F to 158°F)
5% to 95% non-condensing
1.0 m (3.28 ft) drop to plywood over concrete per MIL-STD
810G across operating temperatures with rugged frame.
+/- 8 kV air
+/- 4 kV contact
166
Index
A accessories
charge only cradle . . . . . . . . . . . . . . . . . . . . . . . . . 94
communication and charging cradle . . . . . . . . . . . 97
four slot charge only cradle . . . . . . . . . . . . . . . . . 111
rugged communication and charging cradle . . . . 101
specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
adaptive frequency hopping . . . . . . . . . . . . . . . . . . . . 83
ambient display setting . . . . . . . . . . . . . . . . . . . . . . . . 35
apps
accessing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
datawedge demonstration . . . . . . . . . . . . . . . . . . . 53
RxLogger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
RxLogger Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
B battery
low battery notification . . . . . . . . . . . . . . . . . . . . . 31
battery safety guidelines . . . . . . . . . . . . . . . . . . . . . . 153
bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77, 83
change name . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
power states . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
C
camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43, 48
front camera photo settings . . . . . . . . . . . . . . . . . 51
front camera video settings . . . . . . . . . . . . . . . . . . 52
photo settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
167
rear camera photo settings . . . . . . . . . . . . . . . . . . 50
rear camera video settings . . . . . . . . . . . . . . . . . . 52
taking photos . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
cast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
change bluetooth name . . . . . . . . . . . . . . . . . . . . . . . . 86
charge only cradle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
communication and charging cradle . . . . . . . . . . . . . . 97
cradles
charge only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
communication and charging . . . . . . . . . . . . . . . . 97
four slot charge only . . . . . . . . . . . . . . . . . . . . . . 111
rugged communication and charging . . . . . . . . . 101
D
data capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
datawedge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
datawedge demonstration . . . . . . . . . . . . . . . . . . . . . . 53
decode distances . . . . . . . . . . . . . . . . . . . . . . . 162, 163
decoders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
disconnect host computer . . . . . . . . . . . . . . . . . . . . . . 33
display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
display settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
DS3678
pairing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
pairing using Bluetooth HID . . . . . . . . . . . . . . . . . 72
pairing using simple serial interface . . . . . . . . . . . 71
Index
E
EAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
F
file transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
font size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
four slot charge only cradle . . . . . . . . . . . . . . . . . . . . 111
G
general sound setting . . . . . . . . . . . . . . . . . . . . . . . . . 37
getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
account setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
H
harmful ingredients . . . . . . . . . . . . . . . . . . . . . . . . . . 155
home screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
I
interactive sensor technology . . . . . . . . . . . . . . . . 23, 31
K
keyboards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
L
lithium-ion battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
lock screen notifications . . . . . . . . . . . . . . . . . . . . . . . 42
low battery notification . . . . . . . . . . . . . . . . . . . . . . . . . 31
M maintenance
approved cleanser active ingredients . . . . . . . . . 154
battery safety guidelines . . . . . . . . . . . . . . . . . . . 153
cleaning instructions . . . . . . . . . . . . . . . . . . . . . . 154
maintaining the device . . . . . . . . . . . . . . . . . . . . 153
special cleaning notes . . . . . . . . . . . . . . . . . . . . . 155
168
managing notifications . . . . . . . . . . . . . . . . . . . . . . . . .27
memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
monitor battery usage . . . . . . . . . . . . . . . . . . . . . . . . .30
N
near field communication . . . . . . . . . . . . . . . . . . . . . . .77
near field communications . . . . . . . . . . . . . . . . . . . . . .87
NFC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
notational conventions . . . . . . . . . . . . . . . . . . . . . . . . .12
notification icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
notifications
lock screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
managing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
O
operating system . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
P pairing
DS3678 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
RS507/RS6000 hands-free imager . . . . . . . . . . . .69
using Bluetooth HID (RS507/RS6000) . . . . . . . . .70
using Bluetooth HID(DS3678) . . . . . . . . . . . . . . . .72
using simple serial interface (DS3678) . . . . . . . . .71
using simple serial interface(RS507/RS6000) . . . .69
panoramic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
parts of the tablet
front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
photo transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
photos
camera settings . . . . . . . . . . . . . . . . . . . . . . . . . . .50
panoramic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
taking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Q
quick access panel . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
quick settings
edit icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
R
radios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
related documents . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
related software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
remove wi-fi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
RS507
scanning . . . . . . . . . . . . . . . . . . . . . . . . . .59, 61, 63
RS507 scanning . . . . . . . . . . . . . . . . .61, 63, 66, 67, 69
RS507/RS6000
pairing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
pairing using Bluetooth HID . . . . . . . . . . . . . . . . . .70
pairing using simple serial interface . . . . . . . . . . . 69
RS6000 scanning . . . . . . . . . . . . . . . . . . . . . . . . . 60, 65
rugged communication and charging cradle . . . . . . . 101
RxLogger Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
S scanning
considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
RS507 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59, 61, 63
screen blanking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
screen font size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
setting
camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50, 52
ambient display . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
camera photos . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
camera videos . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
general sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
starting the tablet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
status bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
T
taking a panoramic photo . . . . . . . . . . . . . . . . . . . . . . 49
technical specifications
accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
transferring files using USB . . . . . . . . . . . . . . . . . . . . . 32
troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
U
unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
V
VC Settings
screen blanking . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
videos
camera settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Index
W
WEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Wi-Fi direct . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
wireless local area network . . . . . . . . . . . . . . . . . . . . .77
WLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
WLAN 802.11a/b/g/n . . . . . . . . . . . . . . . . . . . . . . . . . .11
WPA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
WPAN Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
169
www.zebra.com
ダウンロード
ドキュメントの公開リンク
広告
