advertisement
en
Brief and handy: everything your dishwasher needs …
Before using for the first time, read the Installation instructions and Operating instructions!
1
Adjusting the water softening system*
Ask your water supply company what the water hardness is and enter...
* only before the first wash or if the water hardness has been changed
Water hardness value
°Clarke
0-8
9-10
11-12
13-15
16-20
21-26
27-38
39-62
Unscrew cover.
Hardness range soft soft medium medium medium hard hard hard mmol/l
0 -1.1
1.2-1.4
1.5-1.8
1.9-2.1
2.2-2.9
3.0-3.7
3.8-5.4
5.5-8.9
Factory setting
:
:
• ‹‚
:
:
• ‹„
:
:
• ‹†
:
:
• ‹ˆ 2
Filling the salt dispenser Dissolves limescale (not necessary for set value 0!) ...
A B C
Fill the salt dispenser with water before the first wash only.
Quickly sorted ...
How to adjust
– Switch on ON/OFF switch.
– Hold down programme button A and press START button until H:0...
is indicated on the digital display.
– Release both buttons.
The LED for button A flashes and the factory set value of H:04
is indicated on the digital display.
– Press programme button C .
Each time the button is pressed the set value increases by one setting;
when the value reaches H:07 , the display jumps back to H:00 (off).
– Press START button. The chosen setting has now been stored.
Add special salt
(never add detergent!).
Screw on the cover.
Wash immediately.
$ 3
Adding rinse aid Spick and span ...
2
Press mark 1, lift up cover 2.
Fill in rinse aid .
Screw on the cover.
CLICK!
5
4
Adding detergent
Switching on the appliance
6
Select programme
h
Start programme
Here we go...
8
9
Switch off the appliance
Everything o.k....
Start
Reset 3sec.
1 %
A lot of dirt, a lot of detergent ...
If required, open the cover
(press button).
7
Quick, economical or intensive ...
Attention:
Combination products are not suitable for all programmes, follow manufacturer’s instructions.
50 ml
25 ml
15 ml
Pour detergent into the dry detergent dispenser only.
Slide cover shut, press.
PLOP!
Overview of programmes
Intensive
70°
Auto
45°–65°
Eco
50°
7
The max. possible number of programmes is illustrated in this overview.
The corresponding programmes for your appliance can be found on the fascia.
The programme data has been measured in the laboratory according to European standard EN 50242.
Deviations are possible in practice.
* half normal load
Additional options**
Duration: hs : mins
Energy consumption in kWh
Water consumption in litres
With Aquasensor
Ÿ
Express Wash
... is obtained by increased energy consumption
§
at a constant cleaning performance.
Half load
... for a few items, saves water, energy and time.
Flexibility…
± ²
2:15
1,50
14
11
Á á
1:30-2:30
à
2:35
0,95-1,60
-
6-17
0,96
7,0
-
Ï
Intensive zone
... perfect for a mixed load.
Washing pressure and washing temperature are increased slightly.
·
Hygiene
... the temperature is increased during the final rinse process.
This increases the hygiene status.
Gentle
40°
é ê
1:10
0,80
13
10
Quick
45°
ñ ð
0:29 *
0,80
10
-
Prerinse
ù
0:15
0,05
4
-
ø
¿
Extra drying
... improves the drying result by increased temperature in the final rinse.
(Please take care with delicate dishes.)
** depending on model
Maintenance and care
Filters
... check, if required, clean.
Spray arms
...Remove blockages/ deposits.
Rotate filter cylinder, remove filter system...
pull lower arm upwards...
Rectifying minor faults yourself ...
Fault
Display “ 6 ” is lit
Display “ E:24 ” and “ 6 ” are lit
Display “ E:25 ” and “ 6 ” are lit
Other fault display
“ E:XX ” is lit
Residual water in the appliance
Possible causes
Supply fitting jammed or calcified
Waste water hose is blocked or kinked
Cover not attached to waste water pump
Waste water pump blocked
Appliance has technical defect
The programme has not yet ended
... as it is worth doing it yourself!
Remedial action
Open supply fitting.
1. Unscrew water connection.
2. Clean filter in the water connection.
3. Flow rate must be min. 10l/min., when water supply is open.
If the flow rate is less, replace the supply fitting.
Install supply hose without kinks.
Install waste water hose without kinks.
Attach cover (see above).
Clean waste-water pump (see above).
Call factory customer service (state fault display).
Unplug appliance.
Close the appliance and switch it on or terminate the programme (see Terminating the programme).
Rust on the cutlery Cutlery not rust-resistant
Hard knife blades are more susceptible
Extraneous rust
Terminating the programme ...
While the programme is running, press the START button for approx. 3 sec. (Reset).
The numerical display indicates “0:01”; approx. 1 minute after the programme ends,
“0:00” is indicated.
Use dishwasher-proof cutlery.
Never wash rusting parts in the appliance.
Switch off the appliance.
For perfect rinsing results ...
rinse under running water ...
unscrew upper arm … insert ...
Screw on filter system
NOTE
MARK!
Cleaning waste water pump
– Pull out the mains plug.
– Remove filters and scoop out water.
– Lever off cover ( A ).
– Check area around the fan impeller
for foreign objects.
– Click cover shut ( B ).
– Insert filters.
clean spray nozzles under running water
(if required use toothpicks) ...
insert lower arm ...
Fault
Utensils are not clean
Sand or gritty residue on the utensils
Possible causes
Utensils are situated close together or one above the other
Too little detergent
Unsuitable programme selected
Spray arm nozzles blocked
Filters dirty, not seated firmly
Spray arms blocked
A B
2 3
1 screw on upper arm tightly
CLICK!
More information can be found in the operating instructions
Remedial action
Separate the utensils, prevent contact points.
Follow manufacturer’s instructions (detergent).
Select a more intensive programme.
Clean the spray arms (see above).
Clean the filters (see above).
Arrange the utensils so that the spray arms can rotate freely.
Stains and streaks Rinse aid dosage too high/too low
Utensils not dry
Milky deposits on the utensils
(can be removed)
Milky deposits, glasses cloudy/tarnished
(cannot be removed)
Plastic/utensils discoloured
Rinse aid
The combined detergent used has a poor drying performance
Appliance setting
Water softening system incorrectly set
No salt
Glasses not dishwasher-proof
Too little detergent
Discoloration caused by food colourings
(tomato sauce)
Loading the dishwasher correctly ...
Streaks: reduce dosage.
Water or limescale stains: increase dosage.
Increase dosage.
Change the product.
Use rinse aid.
Activate intensive drying (depending on model).
Correctly set water softening system.
Refill with special salt.
Use dishwasher- proof glasses.
Use a detergent suitable for glasses.
Follow manufacturer’s instructions (detergent).
Discoloration is harmless; subsequent rinse cycles will cause it to fade.
Dishwasher-proof utensils (not soiled with ash, wax, lubricating grease, ink or adhesive labels; remove large remnants of jam, milk products and food according to the operating instructions and check that the spray arms can rotate freely.
advertisement
Key Features
- Stainless steel Freestanding
- 13 place settings 7 L 46 dB
- AquaStop function 24 h Delayed start timer
Related manuals
advertisement