This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written consent from NEXCOM

International Co., Ltd.

Disclaimer

The information in this document is subject to change without prior notice and does not represent commitment from NEXCOM International Co., Ltd. However, users may update their knowledge of any product in use by constantly checking its manual posted on our website: http://www.nexcom.com. NEXCOM shall not be liable for direct, indirect, special, incidental, or consequential damages arising out of the use of any product, nor for any infringements upon the rights of third parties, which may result from such use. Any implied warranties of merchantability or fitness for any particular purpose is also disclaimed.

Acknowledgements

ICEK 268-T2 is a trademark of NEXCOM International Co., Ltd. All other product names mentioned herein are registered trademarks of their respective owners.

Regulatory Compliance Statements

This section provides the FCC compliance statement for Class B devices and describes how to keep the system CE compliant.

Declaration of Conformity

FCC

This equipment has been tested and verified to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area

(domestic environment) is likely to cause harmful interference, in which case the user will be required to correct the interference (take adequate measures) at their own expense.

The product(s) described in this manual complies with all applicable

European Union (CE) directives if it has a CE marking. For computer systems to remain CE compliant, only CE-compliant parts may be used. Maintaining

CE compliance also requires proper cable and cabling techniques.

iv ICEK 268-T2 Starter Kit User Manual

Preface

RoHS Compliance

NEXCOM RoHS Environmental Policy and Status

Update

Ltd.

RoHS restricts the use of Lead (Pb) < 0.1% or 1,000ppm, Mercury (Hg) < 0.1% or 1,000ppm, Cadmium (Cd) < 0.01% or 100ppm, Hexavalent Chromium

(Cr6+) < 0.1% or 1,000ppm, Polybrominated biphenyls (PBB) < 0.1% or

1,000ppm, and Polybrominated diphenyl Ethers (PBDE) < 0.1% or 1,000ppm.

In order to meet the RoHS compliant directives, NEXCOM has established an engineering and manufacturing task force to implement the introduction of green products. The task force will ensure that we follow the standard

NEXCOM development procedure and that all the new RoHS components and new manufacturing processes maintain the highest industry quality levels for which NEXCOM are renowned.

The model selection criteria will be based on market demand. Vendors and suppliers will ensure that all designed components will be RoHS compliant.

How to recognize NEXCOM RoHS Products?

For existing products where there are non-RoHS and RoHS versions, the suffix “(LF)” will be added to the compliant product name.

All new product models launched after January 2006 will be RoHS compliant.

They will use the usual NEXCOM naming convention.

v ICEK 268-T2 Starter Kit User Manual

Preface

Warranty and RMA

NEXCOM Warranty Period

NEXCOM manufactures products that are new or equivalent to new in accordance with industry standard. NEXCOM warrants that products will be free from defect in material and workmanship for 2 years, beginning on the date of invoice by NEXCOM. HCP series products (Blade Server) which are manufactured by NEXCOM are covered by a three year warranty period.

NEXCOM Return Merchandise Authorization (RMA)

▪ Customers shall enclose the “NEXCOM RMA Service Form” with the returned packages.

▪ Customers must collect all the information about the problems encountered and note anything abnormal or, print out any on-screen messages, and describe the problems on the “NEXCOM RMA Service

Form” for the RMA number apply process.

▪ Customers can send back the faulty products with or without accessories

(manuals, cable, etc.) and any components from the card, such as CPU and RAM. If the components were suspected as part of the problems, please note clearly which components are included. Otherwise, NEXCOM is not responsible for the devices/parts.

▪ Customers are responsible for the safe packaging of defective products, making sure it is durable enough to be resistant against further damage and deterioration during transportation. In case of damages occurred during transportation, the repair is treated as “Out of Warranty.”

▪ Any products returned by NEXCOM to other locations besides the customers’ site will bear an extra charge and will be billed to the customer.

Repair Service Charges for Out-of-Warranty Products

NEXCOM will charge for out-of-warranty products in two categories, one is basic diagnostic fee and another is component (product) fee.

Repair Service Charges for Out-of-Warranty Products

NEXCOM will charge for out-of-warranty products in two categories, one is basic diagnostic fee and another is component (product) fee.

System Level

▪ Component fee: NEXCOM will only charge for main components such as

SMD chip, BGA chip, etc. Passive components will be repaired for free, ex: resistor, capacitor.

▪ Items will be replaced with NEXCOM products if the original one cannot be repaired. Ex: motherboard, power supply, etc.

▪ Replace with 3rd party products if needed.

▪ If RMA goods can not be repaired, NEXCOM will return it to the customer without any charge.

Board Level

▪ Component fee: NEXCOM will only charge for main components, such as SMD chip, BGA chip, etc. Passive components will be repaired for free, ex: resistors, capacitors.

▪ If RMA goods can not be repaired, NEXCOM will return it to the customer without any charge.

vi ICEK 268-T2 Starter Kit User Manual

Preface

Warnings

Read and adhere to all warnings, cautions, and notices in this guide and the documentation supplied with the chassis, power supply, and accessory modules. If the instructions for the chassis and power supply are inconsistent with these instructions or the instructions for accessory modules, contact the supplier to find out how you can ensure that your computer meets safety and regulatory requirements.

Cautions

Electrostatic discharge (ESD) can damage system components. Do the described procedures only at an ESD workstation. If no such station is available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the computer chassis.

vii ICEK 268-T2 Starter Kit User Manual

Preface

Safety Information

Before installing and using the device, note the following precautions:

▪ Read all instructions carefully.

▪ Do not place the unit on an unstable surface, cart, or stand.

▪ Follow all warnings and cautions in this manual.

▪ When replacing parts, ensure that your service technician uses parts specified by the manufacturer.

▪ Avoid using the system near water, in direct sunlight, or near a heating device.

▪ The load of the system unit does not solely rely for support from the rackmounts located on the sides. Firm support from the bottom is highly necessary in order to provide balance stability.

▪ The computer is provided with a battery-powered real-time clock circuit.

There is a danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.

Discard used batteries according to the manufacturer’s instructions.

Installation Recommendations

Ensure you have a stable, clean working environment. Dust and dirt can get into components and cause a malfunction. Use containers to keep small components separated.

Adequate lighting and proper tools can prevent you from accidentally damaging the internal components. Most of the procedures that follow require only a few simple tools, including the following:

▪ A Philips screwdriver

▪ A flat-tipped screwdriver

▪ A grounding strap

▪ An anti-static pad

Using your fingers can disconnect most of the connections. It is recommended that you do not use needle-nose pliers to disconnect connections as these can damage the soft metal or plastic parts of the connectors.

viii ICEK 268-T2 Starter Kit User Manual

Preface

Safety Precautions

1. Read these safety instructions carefully.

2. Keep this User Manual for later reference.

3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning.

4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a stable surface during installation. Dropping it or letting it fall may cause damage.

7. The openings on the enclosure are for air convection to protect the equipment from overheating. DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source is correct before connecting the equipment to the power outlet.

9. Place the power cord in a way so that people will not step on it. Do not place anything on top of the power cord. Use a power cord that has been approved for use with the product and that it matches the voltage and current marked on the product’s electrical range label. The voltage and current rating of the cord must be greater than the voltage and current rating marked on the product.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient overvoltage.

12. Never pour any liquid into an opening. This may cause fire or electrical shock.

13. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel.

14. If one of the following situations arises, get the equipment checked by service personnel: a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment does not work well, or you cannot get it to work according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage.

15. Do not place heavy objects on the equipment.

16. The unit uses a three-wire ground cable which is equipped with a third pin to ground the unit and prevent electric shock. Do not defeat the purpose of this pin. If your outlet does not support this kind of plug, contact your electrician to replace your obsolete outlet.

17. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY

REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE

RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTERIES

ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS.

ix ICEK 268-T2 Starter Kit User Manual

Preface

Technical Support and Assistance

1. For the most updated information of NEXCOM products, visit NEXCOM’s website at www.nexcom.com.

2. For technical issues that require contacting our technical support team or sales representative, please have the following information ready before calling:

– Product name and serial number

– Detailed information of the peripheral devices

– Detailed information of the installed software (operating system, version, application software, etc.)

– A complete description of the problem

– The exact wordings of the error messages

Warning!

1. Handling the unit: carry the unit with both hands and handle it with care.

2. Maintenance: to keep the unit clean, use only approved cleaning products or clean with a dry cloth.

3. CompactFlash: Turn off the unit’s power before inserting or removing a

CompactFlash storage card.

Conventions Used in this Manual

Warning:

Information about certain situations, which if not observed, can cause personal injury. This will prevent injury to yourself when performing a task.

Caution:

Information to avoid damaging components or losing data.

Note:

Provides additional information to complete a task easily.

x ICEK 268-T2 Starter Kit User Manual

Preface

Global Service Contact Information

Headquarters

NEXCOM International Co., Ltd.

15F, No. 920, Chung-Cheng Rd.,

ZhongHe District, New Taipei City, 23586,

Taiwan, R.O.C.

Tel: +886-2-8226-7786

Fax: +886-2-8226-7782 www.nexcom.com

Japan

NEXCOM Japan

9F, Tamachi Hara Bldg.,4-11-5, Shiba Minato-ku,

Tokyo, 108-0014, Japan

Tel: +81-3-5419-7830

Fax: +81-3-5419-7832

Email: [email protected]

www.nexcom-jp.com

America

USA

NEXCOM USA

2883 Bayview Drive,Fremont CA 94538,

USA

Tel: +1-510-656-2248

Fax: +1-510-656-2158

Email: [email protected]

www.nexcom.com

China

NEXCOM China

2F, Block 4, Venus Plaza, Bldg. 21,

ZhongGuanCun Software Park, No. 8,

Dongbeiwang West Rd., Haidian District,

Beijing, 100193, China

Tel: +86-10-8282-5880

Fax: +86-10-8282-5955

Email: [email protected] www.nexcom.cn

Asia

Taiwan

Central Taiwan Office

16F, No.250, Sec. 2, Chongde Rd.,

Beitun Dist., Taichung City 406, R.O.C.

Tel: +886-4-2249-1179

Fax: +886-4-2249-1172

Email: [email protected]

www.nexcom.com.tw

Shanghai Office

Room 1505, Greenland He Chuang Bldg.,

No. 450 Caoyang Rd.,

Shanghai, 200062, China

Tel: +86-21-6150-8008

Fax: +86-21-3251-6358

Email: [email protected] www.nexcom.cn

Nanjing Office

Hall C, Block 17, Tian Xing Cui Lang Bldg.,

No. 49 Yunnan North Rd.,

Nanjing, 210018, China

Tel: +86-25-8315-3486

Fax: +86-25-8315-3489

Email: [email protected] www.nexcom.cn

Shenzhen Office

Western Room 708, Block 210,

Tairan Industry & Trading Place,

Futian Area, Shenzhen,

518040, China

Tel: +86-755-8332-7203

Fax: +86-755-8332-7213

Email: [email protected] www.nexcom.cn

Wuhan Office

1-C1804/ 1805, Mingze Liwan,

No. 519 South Luoshi Rd.,

Hongshan District,

Wuhan, 430070, China

Tel: +86-27-8722-7400

Fax: +86-27-8722-7400

Email: [email protected] www.nexcom.cn

ICEK 268-T2 Starter Kit User Manual

Preface

Chengdu Office

9F, Shuxiangxie, Xuefu Garden,

No.12 Section 1, South Yihuan Rd.,

Chengdu, 610061, China

Tel: +86-28-8523-0186

Fax: +86-28-8523-0186

Email: [email protected] www.nexcom.cn

Europe

France

NEXCOM France

La Grande Arche-Paroi Nord,

92044 Paris La Défense, France

Tel: +33 (0) 1 40 90 33 35

Fax: +33 (0) 1 40 90 31 01

Email: [email protected] www.nexcom.eu

Germany

NEXCOM GmbH

Leopoldstraße Business Centre,

Leopoldstraße 244,

80807 Munich, Germany

Tel: +49-89-208039-278

Fax: +49-89-208039-279

Email: [email protected]

www.nexcom.eu

Italy

NEXCOM ITALIA S.r.l

Via Gaudenzio Ferrari 29,

21047 Saronno (VA), Italia

Tel: +39 02 9628 0333

Fax: +39 02 9286 9215

Email: [email protected]

www.nexcomitalia.it

United Kingdom

NEXCOM EUROPE

10 Vincent Avenue,

Crownhill Business Centre,

Milton Keynes, Buckinghamshire MK8 0AB,

United Kingdom

Tel: +44-1908-267121

Fax: +44-1908-262042

Email: [email protected]

www.nexcom.eu

xii ICEK 268-T2 Starter Kit User Manual

Preface

Package Contents

Before continuing, verify that the ICEK 268-T2 package that you received is complete. Your package should have all the items listed in the following table.

Item Description

1 ICES 268

2 ICEB 8050C

3 Built-in 10.4” LED LCD Panel

4 Built-in 150W Flex-ATX power supply for AC 110V/220V input

5 NEXCOM USB card containing ICEK 268-T2 Design-in documentation

Qty

xiii ICEK 268-T2 Starter Kit User Manual

Preface

Ordering Information

The following information below provides ordering information for ICEK 268-T2.

ICES 268 (P/N: 10K00026800X0)

COM Express type 2, basic Module QM77 support Intel ® 3rd Generation Core™ rPGA988 embedded processors, non-ECC DDR3/ 2x SO-DIMMs

ICES 268 F-kit (P/N: 10K00026801X0)

COM Express Active fan kits with heat-spreader, heat-sink and cooling fan for ICES 268

ICEB 8050C (P/N: 10KB0805001X0)

COM Express Type 2, COM.0 Rev. 2.0 Evaluation CRB, VGA/ LVDS/ 8x USB 2.0/ 2x COM/ GbE/ LPT/ 5.1 HD/ SPDIF, CF/ IDE/ mSATA/ CFast/ PCIe x16/ PCIe x4

PCIe x1/ PCI/ mPCIe, ATX power input

ICEK 8050C-T2 (P/N: MISC by Project Registered)

COM Express Type 2 Starter Kit ready for NEXOM COM Express compact/ basic modules assembly SO-DIMM system memory with passive/ active fan-sink onto

Type 2 carrier ICEB8050C with bootable Mini-SATA/ CFast-SSD pre-load Win 7 trial version OS with 10.4” LCD/ LVDS display and built-in Flex-ATX PSU AC

110/220V Input

xiv ICEK 268-T2 Starter Kit User Manual

Chapter 1: Product Introduction

Overview - ICES 268 Key Features

▪ Intel ® 3rd generation Intel ® Embedded Core™ rPGA988 embedded processors family

▪ Intel ® QM77 PCH (HM76) chipset support PICMG COM.0 Rev. 2.0 Type

2, pin-outs

▪ Support two DDR3 SO-DIMMs 1333/1600 non-ECC up to 16GB

▪ Support PCIex16 (Gen3.0), 5x PCIex1, 12x USB2.0, 2x SATA3.0/

2x SATA2.0 and 1x GbE

▪ Support VGA, dual channels 18/24-bit LVDS and optional 1x DDI/SDVO by PEG

▪ Dimension: 95mm (W) x 125mm (L)

1 ICEK 268-T2 Starter Kit User Manual

Chapter 1: Product Introduction

Hardware Specifications

CPU Support

▪ Support Intel ® 3rd generation Core™ i7/i5/i3 embedded rPGA988 processors

– Intel ® Core™ i7-3610QE (4x 2.3GHz/ 6MB cache/ Max. TDP 45W)

– Intel ® Core™ i7-3610ME (2x 2.7GHz/ 3MB cache/ Max. TDP 35W)

– Intel ® Celeron ® B810 (2x 1.6GHz/ 2MB cache/ Max. TDP 35W)

Main Memory

▪ Two DDR3 SO-DIMMs, 1333/1600 MHz SDRAM non-ECC up to 16GB

Platform Control Hub

▪ Intel ® QM77 PCH (optional HM76) chipset

BIOS

▪

AMI UEFI System BIOS

Plug and play support

▪ Advanced Power Management and ACPI support

Display

▪ Intel ® HD graphics with DX11 support and supports triple independent displays

▪ One PCI Express x16 Lane (Gen 3.0) down to the carried board

▪ Supports VGA, single/dual channels LVDS 18/24-bit interfaces

▪ Optional 1x DDI port B support HDMI, DVI, DisplayPort and SDVO by PEG with EBK-A2HDMI

Audio

▪ HD audio interface

On-board LAN

▪ Intel ® 82579LM Gigabit Ethernet, support iAMT 8.0 (supported by QM77 only)

▪ Support boot from LAN, wake on LAN function

▪ Signals down to I/O board

COM Express Connector

▪ AB

VGA/ LVDS/ 8x USB 2.0, HD Audio/ 2x SATA3.0, 2x SATA 2.0/ GbE/

GPIO/ LPC bus/ 5 x PCIex1/ SMBus (I2C)/ SPI BIOS / SPK out

▪ CD

PCIex16 (Gen. 3.0) / PCI (v2.3)/ IDE

Power Requirements

▪ +12V, +5VSB, +3.3V RTC power

Dimensions

▪ 95mm (W) x 125mm (L)

Environment

▪

▪ Board level operating temperatures: -15°C to 60°C

▪ Storage temperatures: -20°C to 80°C

Relative humidity:

10% to 90% (operating, non-condensing)

5% to 95% (non-operating, non-condensing)

Certifications

▪

▪ CE approval

FCC Class A

2 ICEK 268-T2 Starter Kit User Manual

Chapter 1: Product Introduction

Knowing Your ICES 268

PCIe DIP switch

CPU Fan

CPU socket

Support DDR3/ SO-DIMM

ICEK 268-T2 Starter Kit User Manual

Chapter 1: Product Introduction

Overview - ICEB 8050C Key Features

▪ COM Express COM.0, Rev2.0 evaluation carrier, ATX form-factor

▪ Support Type 2 pin-outs, COMe Extended/ Basic/ Compact Module

▪ Display: VGA & dual channels 18/24-bit LVDS

▪ Bootable CFAST or mini-SATA, CF and shared IDE

▪ PCIe x16, PCIe x4, PCIe x1, PCIx 1 and mini-PCIe for Wi-Fi

▪ PS2/KB/Mouse, LPT/ RS232/422/485, VGA/GbE/4USB/ 5.1, S/PDIF

4 ICEK 268-T2 Starter Kit User Manual

Chapter 1: Product Introduction

Hardware Specifications

Form Factor

▪ ATX Carrier MB, dimension: 305mm x 244mm (12” x 9.9”)

▪ COM Express Evaluation CRB: PICMB COM Express board-to-board interconnectors, type 2 pin-puts, female, 8mm stack-up height,

COM.0 Rev. 2.0

NEXCOM Computer-on-Modules Support List

▪

▪ Compact Size (95x 95mm) : ICES 251/ ICES 251X, ICES 253, ICES 254

Basic Size (125x 95mm) : ICES 270, ICES 267/ ICES 267S

Expansion

▪

▪ 1x PCIe x16 slot, support PEG interfaces

▪ 1x PCIe x4 slot, optional 4x PCIe x1 signals

1x PCIe x1 slot and 1x PCI (v2.3) slot

▪ 1x mini-PCIe slot for Wi-Fi with SIM tray

Graphic Interfaces

▪

▪ Graphic Chip: from Type 2 pin-out, COM Express module

▪ CRT: support analog VGA with DB15 connector on the I/O edge

LVDS: dual channels 18/24-bit LVDS connector (dual DF-13-20P)

▪ PCIe x16: optional EBK-A2HDMI (ICES254 only) riser card for HDMI or DP

Super I/O

▪ Winbond W83627DHG-PT

I/O Interface

▪ Serial COM: 2 ports

– 1x edge DB9 connector to support RS232/ 422/ 485 (+5/ +12V by

Ring)

– 1x internal box-header 2.0 pitch to support RS232

▪ USB 2.0: 8 ports

– 4x USB 2.0 ports by stack Type A on edge

– 3x USB 2.0 by 4-pins JST 2.0mm JST connector,

– 1x internal USB 2.0 to mini-PCIe slot for external Wi-Fi module

▪ SATA 2.0: 4 ports

– 2x SATA 2.0 ports

– 1x mini-SATA by mini-PCIe slot for half-/ full size mSATA-SSD

▪

– 1x CFAST slot for CFAST/ SATA 2.0

CF: 1x CF/ shared IDE slot onboard (default master-mode)

▪ IDE: 1x 44pins box-header for legacy IDE-HDD

▪

PS/2: 2x PS/2 connectors on edge for Keyboard/ Mouse

Printer Port: 1x DB25 on edge for legacy printer interface

▪ GPIO ports: 8x pins GPIO signals from COMe

(default 5V TTL/ option 3.3V)

Network

▪

▪ LAN chip: from COMe CPU module

Support 1x RJ45/ GbE port on the edge I/O

Audio

▪

▪ HD Audio AL886 with 5.1 channels

Support external S/PDIF interface

▪ Support internal pin-header for L/R speaker-out 2W/ 4 Ohm

5 ICEK 268-T2 Starter Kit User Manual

Chapter 1: Product Introduction

EEPROM

▪ 1x 2K EEPROM to record PCI Express Lane configuration

▪ ATMEL AT24C32 (or C02) and address 0x57 or (0xAE)

Watchdog Timer

▪ Watchdog timeout can be programmed by software from 1 second to 255 seconds and from 1 minute to 255 minutes (Tolerance 15% temperature

25°C)

On-board RTC

▪ On-chip RTC with battery BR2032

Power Input

▪ Standard ATX 24 pins and AUX 4-pins with 12V

Dimensions

▪ ATX form factor, 305x 244mm (Lx W, 12”x9.6”)

Environment

▪

▪ Operating temperatures: -20°C to 60°C

Storage temperature: -40°C to 85°C

▪ Relative humidity: Operating 10% to 90%, non-condensing

Certifications

▪

▪ CE approval

FCC Class A

6 ICEK 268-T2 Starter Kit User Manual

Chapter 1: Product Introduction

Knowing Your ICEB 8050C

CFast/ SSD

PCIe x1 PCI (v2.3)

PCIe x4 PCIe x16

HD 5.1

Audio, S/PDIF

2USB

GbE LAN/2USB PS/2/ KB & Mouse

RS232/422/485

LPT/ VGA

mPCIe/ Wi-Fi

Option SIM mSATA/SSD

ATX Power

IDE (44pins)

18/24-bit LVDS

CF Slot Port 80

Battery RTC

7 ICEK 268-T2 Starter Kit User Manual

Chapter 1: Product Introduction

Block Diagram

ICES 268

PORT:0-3

PORT:A.B

PORT:0-7

VGA BUS

HDA BUS

SATA BUS

LVDS BUS

USB2.0 BUS

LPC BUS

TYPE 2

PCI-E*1 BUS PORT:1,2,3,4,5,

MDI BUS

INTEL WG82579LM

GbE PHY

PCI-E*1 BUS PORT:8

SMBUS

SPI BUS

IMVP 7

Vcore

GFXCORE

Ivy Bridge

DDR3 CH A

37.5 x 37.5 mm Socket

(rPGA989)

FDI DMI

Flexible

Display

Interface

FDI

Panther Point

DMI

DMI(X4)

DDR3 Channel A

DDR3 Channel B

DDR3 1600 MHz NON-ECC SO-DIMM

PCIex16 BUS

DISPLAY PORT B

QM77/HM76

25 x 25 mm

FCBGA(Mobile only)

PCIE*1 PORT:6

PCIE*1 PORT:7

PCIE TO PATA

88SE6101

PCIE TO PCI

IT8892

PATA

PCI

PCIE BUS SMBUS SPI

HWM

NCT7802Y

BIOS iAMT

SPI ROM

TYPE 2

8 ICEK 268-T2 Starter Kit User Manual

Chapter 1: Product Introduction

ICEB 8050C

SATA *2

Connector mSATA

Connector

CFAST

Connector

USB 2.0 *7

Connector

PCI-E x4

SLOT

PCI-E x1

SLOT

MiniPCIE

SLOT

KB/MS

Connector

COM 1

232/422/485

Connector

COM 2

232

Connector

LPT

Connector

SUPER I/O

(W83627DHG-PT)

LPC BUS

SATA x2 BUS

SATA x1 BUS

USB BUS

PCI-E x4 BUS

PCI-E x1 BUS

USB x1

R/G/B

LVDS Channel A

LVDS Channel B

HD Audio interface

VGA

Connector

LVDS A

Connector

(18/24 bit)

LVDS B

Connector

(18/24 bit)

SPEAKER

HEARD

Audio Codec

(ALC886) AMP

TYPE 2

Page 3

I2C BUS

GPIO BUS

TTL LEVLE

Giga LAN

Audio Connector

Line IN / Line OUT / MIC IN

CEN OUT / SIDE OUT / SPDIF Line OUT

EEPROM

GPI *4

GPO *4

RJ45

Connector

TYPE 2

PCI BUS 33MHz/32bit

PCI SLOT

IDSEL=AD20

IRQ=A B C D

PATA 100/66/33

IDE 44PIN

Box header

Slave

CF Socket

Master x16 PEG BUS

PCI-E x16

SLOT

9 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

This chapter describes how to set the jumpers and connectors on the

ICES 268 and ICEB 8050C motherboard.

Before You Begin

▪ Ensure you have a stable, clean working environment. Dust and dirt can get into components and cause a malfunction. Use containers to keep small components separated.

▪ Adequate lighting and proper tools can prevent you from accidentally damaging the internal components. Most of the procedures that follow require only a few simple tools, including the following:

– A Philips screwdriver

– A flat-tipped screwdriver

– A set of jewelers screwdrivers

– A grounding strap

– An anti-static pad

▪ Using your fingers can disconnect most of the connections. It is recommended that you do not use needle-nosed pliers to disconnect connections as these can damage the soft metal or plastic parts of the connectors.

▪ Before working on internal components, make sure that the power is off.

Ground yourself before touching any internal components, by touching a metal object. Static electricity can damage many of the electronic components. Humid environments tend to have less static electricity than dry environments. A grounding strap is warranted whenever danger of static electricity exists.

Precautions

Computer components and electronic circuit boards can be damaged by discharges of static electricity. Working on computers that are still connected to a power supply can be extremely dangerous.

Follow the guidelines below to avoid damage to your computer or yourself:

▪ Always disconnect the unit from the power outlet whenever you are working inside the case.

▪ If possible, wear a grounded wrist strap when you are working inside the computer case. Alternatively, discharge any static electricity by touching the bare metal chassis of the unit case, or the bare metal body of any other grounded appliance.

▪ Hold electronic circuit boards by the edges only. Do not touch the components on the board unless it is necessary to do so. Don’t flex or stress the circuit board.

▪ Leave all components inside the static-proof packaging that they shipped with until they are ready for installation.

▪ Use correct screws and do not over tighten screws.

10 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

Jumper Settings

A jumper is the simplest kind of electric switch. It consists of two metal pins and a cap. When setting the jumpers, ensure that the jumper caps are placed on the correct pins. When the jumper cap is placed on both pins, the jumper is short. If you remove the jumper cap, or place the jumper cap on just one pin, the jumper is open.

Refer to the illustrations below for examples of what the 2-pin and 3-pin jumpers look like when they are short (on) and open (off).

Two-Pin Jumpers: Open (Left) and Short (Right)

Three-Pin Jumpers: Pins 1 and 2 are Short

11 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

Locations of the Jumpers and Connectors for ICES 268

The figure below shows the locations of the jumpers and connectors on the top and bottom of ICES 268.

SW1

FAN1

C20

C25

204

DIMM1

203

ICES268 VER:A

4BKS0268A1X10

MADE IN TAIWAN

2 1

D110

C110

B110

A110

DIMM2

VER:A ICES268

4BKS0268A1X10

MADE IN TAIWAN

204

12 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

Connector Pin Definitions

Internal Connectors

PCIe DIP Switch

Connector type: 1x4 4-pin DIP switch

Connector location: SW1

O N

1 2

Pin

Definition

CFG5

GND

Pin

Definition

CFG6

GND

PCI Express Bifurcation (CFG6) (CFG5)

CFG6 CFG5

0 0 1 x8, 2 x4 PCI Express

1 reserved

2 x8 PCI Express

1 x16 PCI Express (Default)

CPU Fan Connector

Connector type: 1x3 3-pin header

Connector location: FAN1

Pin

Definition

GND

VCC5_S

Pin

Definition

VCC12

13 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

High Speed Board-to-Board Connector: Row A and B, Row C and D

Connector location: J3

Com Express A&B Connector

Com Express C&D Connector

Pin

A10

A11

A12

A13

Definition

GND(FIXED)

GBE0_MDI3-

GBE0_MDI3+

GBE0_LINK100#

GBE0_LINK1000#

GBE0_MDI2-

GBE0_MDI2+

GBE0_LINK#

GBE0_MDI1-

GBE0_MDI1+

GND(FIXED)

GBE0_MDI0-

GBE0_MDI0+

Pin

B10

B11

B12

B13

Definition

GND(FIXED)

GBE0_ACT#

LPC_FRAME#

LPC_AD0

LPC_AD1

LPC_AD2

LPC_AD3

LPC_DRQ0#

LPC_DRQ1#

LPC_CLK

GND(FIXED)

PWRBTN#

SMB_CK

Pin

C10

C11

C12

C13

Definition

GND(FIXED)

IDE_D7

IDE_D6

IDE_D3

IDE_D15

IDE_D8

IDE_D9

IDE_D2

IDE_D13

IDE_D1

GND(FIXED)

IDE_D14

IDE_IORDY

Pin

D10

D11

D12

D13

Definition

GND(FIXED)

IDE_D5

IDE_D10

IDE_D11

IDE_D12

IDE_D4

IDE_D0

IDE_REQ#

IDE_IOW#

IDE_ACK#

GND(FIXED)

IDE_IRQ#

IDE_A0

ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

Pin

A34

A35

A36

A37

A38

A39

A40

A41

A24

A25

A26

A27

A28

A29

A30

A31

A32

A33

A14

A15

A16

A17

A18

A19

A20

A21

A22

A23

Definition

GBE0_CTREF

SUS_S3#

SATA0_TX+

SATA0_TX-

SUS_S4#

SATA0_RX+

SATA0_RX-

GND(FIXED)

SATA2_TX+

SATA2_TX-

SUS_S5#

SATA2_RX+

SATA2_RX-

BATLOW#

(S)ATA_ACT#

AC/HDA_SYNC

AC/HDA_RST#

GND(FIXED)

AC/HDA_BITCLK

AC/HDA_SDOUT

BIOS_DIS0#

THRMTRIP#

USB6-

USB6+

USB_6_7_OC#

USB4-

USB4+

GND(FIXED)

Pin

B34

B35

B36

B37

B38

B39

B40

B41

B24

B25

B26

B27

B28

B29

B30

B31

B32

B33

B14

B15

B16

B17

B18

B19

B20

B21

B22

B23

Definition

SMB_DAT

SMB_ALERT#

SATA1_TX+

SATA1_TX-

SUS_STAT#

SATA1_RX+

SATA1_RX-

GND(FIXED)

SATA3_TX+

SATA3_TX-

PWR_OK

SATA3_RX+

SATA3_RX-

AC/HDA_SDIN2

AC/HDA_SDIN1

AC/HDA_SDIN0

GND(FIXED)

SPKR

I2C_CK

I2C_DAT

USB7-

USB7+

USB_4_5_OC#

USB5-

USB5+

GND(FIXED)

Pin

C34

C35

C36

C37

C38

C39

C40

C41

C24

C25

C26

C27

C28

C29

C30

C31

C32

C33

C14

C15

C16

C17

C18

C19

C20

C21

C22

C23

Definition

IDE_IOR#

PCI_PME#

PCI_GNT2#-

PCI_REQ2#

PCI_GNT1#

PCI_REQ1#

PCI_GNT0#

GND(FIXED)

PCI_REQ0#

PCI_RST#

PCI_AD0

PCI_AD2

PCI_AD4

PCI_AD6

PCI_AD8

PCI_AD10

PCI_AD12-

GND(FIXED)

PCI_AD14

PCI_CBE#1-

PCI_PERR#

PCI_LOCK#

PCI_DEVSEL#

PCI_IRDY#

PCI_CBE#2

PCI_AD17

PCI_1D19

GND(FIXED)

Pin

D34

D35

D36

D37

D38

D39

D40

D41

D24

D25

D26

D27

D28

D29

D30

D31

D32

D33

D14

D15

D16

D17

D18

D19

D20

D21

D22

D23

Definition

IDE_A1

IDE_A2

IDE_CS1#

IDE_CS3#

IDE_RST#

PCI_GNT3#

PCI_REQ3#

GND(FIXED)

PCI_AD1

PCI_AD3

PCI_AD5

PCI_AD7

PCI_CBE#0

PCI_AD9

PCI_AD11

PCI_AD13

PCI_AD15

GND(FIXED)

PCI_PAR

PCI_SERR#

PCI_STOP#

PCI_TRDY#

PCI_FRAME#

PCI_AD16

PCI_AD18

PCI_AD20

PCI_AD22

GND(FIXED)

ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

Pin

A62

A63

A64

A65

A66

A67

A68

A69

A57

A58

A59

A60

A61

A52

A53

A54

A55

A56

A42

A43

A44

A45

A46

A47

A48

A49

A50

A51

Definition

USB2-

USB2+

USB_2_3_OC#

USB0-

USB0+

VCC_RTC

EXCD0_PERST#

LPC_SERIRQ

GND(FIXED)

GPI0

PCIE_TX4+

PCIE_TX4-

GND

PCIE_TX3+

PCIE_TX3-

GND(FIXED)

PCIE_TX2+

PCIE_TX2-

GPI1

PCIE_TX1+

PCIE_TX1-

GND

GPI2

PCIE_TX0+

PCIE_TX0-

Pin

B62

B63

B64

B65

B66

B67

B68

B69

B57

B58

B59

B60

B61

B52

B53

B54

B55

B56

B42

B43

B44

B45

B46

B47

B48

B49

B50

B51

Definition

USB3-

USB3+

USB_0_1_OC#

USB1-

USB1+

EXCD1_PERST#

SYS_RESET#

CB_RESET#

GND(FIXED)

NC-

GPO1

PCIE_RX4+

PCIE_RX4-

GPO2

PCIE_RX3+

PCIE_RX3-

GND(FIXED)

PCIE_RX2+

PCIE_RX2-

GPO3

PCIE_RX1+

PCIE_RX1-

WAKE0#

WAKE1#

PCIE_RX0+

PCIE_RX0-

Pin Definition Pin

C42

C43

C44

C45

C46

C47

C48

C49

C50

C51

PCI_AD21

PCI_AD23

PCI_CBE#3

PCI_AD25

PCI_AD27

PCI_AD29

PCI_AD31

PCI_IRQ#A

PCI_IRQ#B

GND(FIXED)

C62

C63

C64

C65

C66

C67

C68

C69

C52

C53

C54

C55

C56

SDVO_TVCLKP/PEG_RX0+

SDVO_TVCLKN/PEG_RX0-

TYPE0#

SDVO_INTP/PEG_RX1+

SDVO_INTN/PEG_RX1-

C57 TYPE1# D57

C58 SDVO_FLDSTALP/PEG_RX2+ D58

C59 SDVO_FLDSTALN/PEG_RX2D59

C60 GND(FIXED) D60

C61 PEG_RX3+ D61

D52

D53

D54

D55

D56

PEG_RX3-

RSVD

PEG_RX4+

PEG_RX4-

RSVD

PEG_RX5+

PEG_RX5-

D62

D63

D64

D65

D66

D67

D68

D69

D42

D43

D44

D45

D46

D47

D48

D49

D50

D51

Definition

PCI_AD24

PCI_AD26

PCI_AD28

PCI_AD30

PCI_IRQ#C

PCI_IRQ#D

PCI_M66EN

PCI_CLK

GND(FIXED)

PEG_TX0+/SDVO_RP

PEG_TX0-/SDVO_RN

PEG_LANE_RV#

PEG_TX1+/SDVO_GP

PEG_TX1-/SDVO_GN

TYPE2#

PEG_TX2+/SDVO_BP

PEG_TX2-/SDVO_BN

GND(FIXED)

PEG_TX3+/SDVO_CLKP

PEG_TX3-/SDVO_CLKN

RSVD

PEG_TX4+

PEG_TX4-

GND

PEG_TX5+

PEG_TX5-

ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

Pin

A90

A91

A92

A93

A94

A95

A96

A97

A80

A81

A82

A83

A84

A85

A86

A87

A88

A89

A70

A71

A72

A73

A74

A75

A76

A77

A78

A79

Definition

GND(FIXED)

LVDS_A0+

LVDS_A0-

LVDS_A1+

LVDS_A1-

LVDS_A2+

LVDS_A2-

LVDS_VDD_EN

LVDS_A3+

LVDS_A3-

GND(FIXED)

LVDS_A_CK+

LVDS_A_CK-

LVDS_I2C_CK

LVDS_I2C_DAT

GPI3

RSVD(KBD_RST#)

RSVD(A20GATE)

PCIE_CLK_REF+

PCIE_CLK_REF-

GND(FIXED)

SPI_POWER

SPI_MISO

GPO0

SPI_CLK

SPI_MOSI

GND

TYPE10#

Pin

B90

B91

B92

B93

B94

B95

B96

B97

B80

B81

B82

B83

B84

B85

B86

B87

B88

B89

B70

B71

B72

B73

B74

B75

B76

B77

B78

B79

Definition

GND(FIXED)

LVDS_B0+

LVDS_B0-

LVDS_B1+

LVDS_B1-

LVDS_B2+

LVDS_B2-

LVDS_B3+

LVDS_B3-

LVDS_BKLT_EN

GND(FIXED)

LVDS_B_CK+

LVDS_B_CK-

LVDS_BKLT_CTRL

VCC_5V_SBY

BIOS_DIS1#

VGA_RED

GND(FIXED)

VGA_GRN

VGA_BLUE

VGA_HSYNC

VGA_VSYNC

VGA_I2C_CK

VGA_I2C_DAT

SPI_CS#

Pin

C90

C91

C92

C93

C94

C95

C96

C97

C80

C81

C82

C83

C84

C85

C86

C87

C88

C89

C70

C71

C72

C73

C74

C75

C76

C77

C78

C79

Definition

GND(FIXED)

PEG_RX6+

PEG_RX6-

SDVO_DATA

PEG_RX7+

PEG_RX7-

GND

RSVD

PEG_RX8+

PEG_RX8-

GND(FIXED)

PEG_RX9+

PEG_RX9-

RSVD

GND

PEG_RX10+

PEG_RX10-

GND

PEG_RX11+

PEG_RX11-

GND(FIXED)

PEG_RX12+

PEG_RX12-

GND

PEG_RX13+

PEG_RX13-

GND

RSVD

Pin

D90

D91

D92

D93

D94

D95

D96

D97

D80

D81

D82

D83

D84

D85

D86

D87

D88

D89

D70

D71

D72

D73

D74

D75

D76

D77

D78

D79

Definition

GND(FIXED)

PEG_TX6+

PEG_TX6-

GND

PEG_TX7+

PEG_TX7-

GND

IDE_CBLID#

PEG_TX8+

PEG_TX8-

GND(FIXED)

PEG_TX9+

PEG_TX9-

RSVD

GND

PEG_TX10+

PEG_TX10-

GND

PEG_TX11+

PEG_TX11-

GND(FIXED)

PEG_TX12+

PEG_TX12-

GND

PEG_TX13+

PEG_TX13-

GND

PEG_EN#

ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

Pin

A98

A99

A100

A101

A102

A103

A104

A105

A106

A107

A108

A109

A110

Definition

GND(FIXED)

VCC_12V

GND(FIXED)

Pin

B98

B99

B100

B101

B102

B103

B104

B105

B106

B107

B108

B109

B110

Definition

RSVD

GND(FIXED)

VCC_12V

GND(FIXED)

Pin

C98

C99

C100

C101

C102

C103

C104

C105

C106

C107

C108

C109

C110

Definition

PEG_RX14+

PEG_RX14-

GND(FIXED)

PEG_RX15+

PEG_RX15-

GND

VCC_12V

GND(FIXED)

Pin

D98

D99

D100

D101

D102

D103

D104

D105

D106

D107

D108

D109

D110

Definition

PEG_TX14+

PEG_TX14-

GND(FIXED)

PEG_TX15+

PEG_TX15-

GND

VCC_12V

GND(FIXED)

18 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

Locations of the Jumpers and Connectors for ICEB 8050C

The figure below shows the location of the jumpers and connectors for ICEB 8050C.

LED5

JP3 CF MODE

1-2 MASTER

2-3 SLAVE

JP4 HDDLED

1 HDDLED+

2 HDDLED-

44 43

JP3

1 2 1

JP4

JP5

2 1 2 1

JP8

2 1

JP6

3 1 3

JP9

JP5 POWER BUTTON

JP6 HW RESET

JP8 DISABLE EEPROM WP

1 JP10

H14

13 CON2

IDE1

CN1 4

JP7 BIOS PROGRAM

JP7

4 4

9 10

CN4

JP9 POWER MODE

1-2 ATX

2-3 AT

CN7

1 2 1

JP10 LVDS POWER

1-2 3.3V

2-3 5V

H10

20 19

H15

MH3

CN8

MH4

H6 H11

1 mSATA

16 18

15 17

MH5

CN9

12 1

MH6

CON3

MH3 MH4

ICEB8050C

4BK08050B2X10

MADE IN TAIWAN

VER:B mPCIE

J11

16 18

15 17

CN10

JP13

1-2

2-3 mPCIESELECT

WIFI

3.5G

H20

BIOS_

DIS1#

SW3

BIOS_

DIS0#

CARRIER

SPI_CS#

HIGH

SPI0

SPI1

BIOS SELECT

SPI

DESCRIPTOR

MODULE

CARRIER

MODULE

SW3

BIOS_DIS0#

BIOS_DIS1#

BIOS ENTRY

SIP0/SPI1

CARRIER FWH

SIP0/SPI1

ON:0

OFF:1

SW3.1

SW3.2

H18

J1 U21

1 2

JP12

9 10

JP1

103

128

1 JP2

102

BAT1

C14

KM1

8 7

COM1

H21

C1 B1

H12

PRT1

VGA1

22 21

CN2

20 19

G/R

CN3

H13

CN6

CON1

45 42 35 32

55 52 25

5 4 1

A B C CN5

3 2

A1 B1 B2

H16

JP11 H17

J10

JP11

INTERNAL

SPEAKER

1 L+

2 L-

3 GND

4 R+

5 R-

CON4

R350

S1 S7

CFAST

CN11

H19

19 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

Jumpers

AT/ATX Power Type Select

Connector type: 1x3 3-pin header, 2.54mm pitch

Connector location: JP9

1 3

Pin

1-2 On

2-3 On

1-2 On: default

Settings

ATX

RTC Clear

Connector type: 1x3 3-pin header, 2.54mm pitch

Connector location: J1

1 3

Pin

1-2 On

2-3 On

1-2 On: default

Settings

Normal

Clear CMOS

20 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

LVDS Backlight Power Select

Connector type: 1x3 3-pin header, 2.54mm pitch

Connector location: JP10

1 3

Pin

1-2 On

2-3 On

1-2 On: default

Settings

+3.3V

+5V

COM1 RS232 RI# Pin Power Select

Connector type: 1x3 3-pin header, 2.54mm pitch

Connector location: JP2

1 5

Pin

1-2 On

2-3 On

4-5 On

4-5 On: default

Settings

+5V

+12V

21 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

Termal R

Connector type: 1x3 3-pin header, 2.54mm pitch

Connector location: JP1

1 3

Pin

1-2 On

2-3 On

2-3 On: default

Settings

Enable COM1 422/485 Termal R

Disable COM1 422/485 Termal R

CF Mode Select

Connector type: 1x3 3-pin header, 2.54mm pitch

Connector location: JP3

1 3

Pin

1-2 On

2-3 On

1-2 On: default

Settings

Master

Slave

22 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors mPCIe Select

Connector type: 1x3 3-pin header, 2.54mm pitch

Connector location: JP13

1 3

Pin

1-2 On

2-3 On

1-2 On: default

Settings

Wi-Fi

3.5G

23 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

DIP Switch Settings

Close to Net LPC_SIO1_CLK

Connector type: 2x2 4-pin DIP switch

Connector location: SW1

Pin

1-2 Off

1-2 On

O N

1 2

Settings

Enable

Disable

RS232/ RS422/ RS485 Mode Select

Connector type: 2x4 8-pin DIP switch

Connector location: SW2

O N

1 2 3 4

MODE0

MODE1

MODE2

MODE3

SW2

SW2.1

SW2.2

SW2.3

SW2.4

Loop Back

RS232

ON:0 OFF:1

MODE0

MODE1

MODE2

DIR

RS422

RS485

ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

BIOS Select

Connector type: 2x2 4-pin DIP switch

Connector location: SW3

O N

1 2

SW3

SW3.1

SW3.2

ON:0 OFF:1

BIOS_DIS0#

BIOS_DIS1#

BIOS_DIS1# BIOS_DIS0#

Carrier

SPI_CS#

High

SPI0

SPI1

SPI

Descriptor

Module

CARRIER

MODULE

BIOS Entry

SPI0/SPI1

Carrier FWH

SPI0/SPI1

25 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

Pin

MH1

MH3

MH5

Connector Pin Definitions

External Connectors

PS2 Keyboard and Mouse

Connector type: PS/2, Mini-DIN-6

Connector location: KM1

Mouse

Keyboard

Definition

KDAT

GND

KCLK

MDAT

GND

MCLK

GND

Pin

MH2

MH4

Definition

+5V

GND

Parallel Port

Connector type: 26-pin D-Sub, 2x13 (2.0mm)

Connector location: PRT1

Pin

MH2

Definition

RP_-STB

RP_PRD1

RP_PRD3

RP_PRD5

RP_PRD7

BUSY

SLCT

ERR#

SLIN#

GND

Pin

MH1

MH3

Definition

RP_PRD0

RP_PRD2

RP_PRD4

RP_PRD6

ACK#

AFD#

INIT#

GND

26 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

COM1 Port

Connector type: DB-9 port, 9-pin D-Sub

Connector location: COM1

VGA Port

Connector type: DB-15 port, 15-pin D-Sub (VGA)

Connector location: VGA1

Pin

MH2

Definition

SP_DCD1

SP_TXD1

GND

SP_RTS1

SP_RI1_T

GND

Pin

MH1

Definition

SP_RXD1

SP_DTR1

SP_DSR1

SP_CTS1

GND

Pin

MH2

Definition

VGA_R

VGA_B

GND

+5V

VGA_HSYNC

VGA_CLK

GND

Pin

MH1

Definition

VGA_G

VGADET

GND

VGA_DAT

VGA_VSYNC

GND

27 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

LAN and USB1/2 Ports

Connector type: RJ45 port with LEDs and dual USB 2.0 ports, Type A

Connector location: CN2A (USB) and CN2B (LAN)

ACT LINK

USB2/3 Ports

Connector type: Dual USB 2.0 ports, Type A

Connector location: CON1

Pin

MH1

MH3

MH5

MH7

Definition

+5V_USB

USB_0P

+5V_USB

USB_1P

GND

V25_LA1

LAN_MDI0N

LAN_MDI1N

LAN_MDI2N

LAN_MDI3N

LAN_SPEED100#

LAN_ACTLED#

GND

Pin

MH2

MH4

MH6

MH8

Definition

USB_0N

GND

USB_1N

GND

LAN_MDI0P

LAN_MDI1P

LAN_MDI2P

LAN_MDI3P

GND

LAN_SPEED1000#

+3.3VSBY

GND

Pin

MH1

MH3

Definition

+5V_USB

USB_2P

+5V_USB

USB_3P

GND

Pin

MH2

MH4

Definition

USB_2N

GND

USB_3N

GND

ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

Pin

MH2

MH4

Audio Connectors

Connector type: 5x 3.5mm TRS, 1x S/PDIF

Connector location: CN5

Rear Surround

Center Subwoofer

S/PDIF

Line-in

Line-out

Mic-in

Definition

GND

MIC_JD1

MIC_R

FRONT_JD

FRONT_R2

LINE1_JD

LINEIN_R

CEN_OUT

GND

SIDE_L

GND

SPDIFO

GND

Pin

MH1

MH3

Definition

MIC_L

GND

FRONT_L2

GND

LINEIN_L

GND

CEN_JD

LEF_OUT

SIDESURR_JD

SIDE_R

+5V

GND

29 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

Internal Connectors

HDD LED

Connector type: 1x2 2-pin header, 2.54mm pitch

Connector location: JP4

1 2

Pin

Definition

+5V

GND

Internal Speaker

Connector type: 1x5 5-pin header, 2.0mm pitch

Connector location: JP11

Pin

Definition

SPKR_L+

SPKR_L-

GND

SPKR_R+

SPKR_R-

30 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

USB 5 Port

Connector type: 1x4 4-pin header, 2.0mm pitch

Connector location: J3

Pin

Definition

+5V_USB

USB_5N

USB_5P

GND

USB 6 Port

Connector type: 1x4 4-pin header, 2.0mm pitch

Connector location: J4

Pin

Definition

+5V_USB

USB_6N

USB_6P

GND

31 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

USB 7 Port

Connector type: 1x4 4-pin header, 2.0mm pitch

Connector location: J5

Pin

Definition

+5V_USB

USB_7N

USB_7P

GND

COM2 RS232

Connector type: 2x5 10-pin header, 2.0mm pitch

Connector location: J2

Pin

Definition

SP_DCD2

SP_TXD2

GND

SP_RTS2

SP_RI2

Pin

Definition

SP_RXD2

SP_DTR2

SP_DSR2

SP_CTS2

32 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

GPIO

Connector type: 2x5 10-pin header, 2.0mm pitch

Connector location: J6

Pin

Definition

+5V

ICH_GPO0_OUT

ICH_GPO1_OUT

ICH_GPO2_OUT

ICH_GPO3_OUT

Pin

Definition

GND

ICH_GPI0_IN

ICH_GPI1_IN

ICH_GPI2_IN

ICH_GPI3_IN

CCFL

Connector type: 1x7 7-pin header, 2.0mm pitch

Connector location: J7

Pin

Definition

+5V

ICH_GPO0_OUT

ICH_GPO1_OUT

ICH_GPO2_OUT

ICH_GPO3_OUT

Pin

Definition

GND

ICH_GPI0_IN

ICH_GPI1_IN

ICH_GPI2_IN

ICH_GPI3_IN

33 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

LVDS Channel A

Connector type: 2x10 20-pin header, 1.25mm pitch

Connector location: CN7

Pin

MH1

Definition

LVDS_DDC_CLK

Panel_VDD

LVDSA_DATA3

LVDSA_DATA#3

GND

LVDSA_CLK

LVDSA_CLK#

GND

LVDSA_DATA2

LVDSA_DATA#2

GND

Pin

MH2

Definition

LVDS_DDC_DATA

LVDSA_DATA0

LVDSA_DATA#0

Panel_VDD

LVDSA_DATA1

LVDSA_DATA#1

GND

Panel_backlight

GND

LVDS Channel B

Connector type: 2x10 20-pin header, 1.25mm pitch

Connector location: CN4

Pin

MH1

Definition

LVDS_DDC_CLK

Panel_VDD

LVDSB_DATA3

LVDSB_DATA#3

GND

LVDSB_CLK

LVDSB_CLK#

GND

LVDSB_DATA2

LVDSB_DATA#2

GND

Pin

Definition

LVDS_DDC_DATA

LVDSB_DATA0

LVDSB_DATA#0

Panel_VDD

LVDSB_DATA1

LVDSB_DATA#1

GND

Panel_backlight

GND

34 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

GAL Download Port

Connector type: 1x6 6-pin header, 2.54mm pitch

Connector location: JP12

Pin

Definition

+3.3V

TCK

TDI

Pin

Definition

GND

TDO

TMS

SPI

Connector type: 2x4 8-pin header, 1.27mm pitch

Connector location: JP7

Pin

Definition

SPI_CS

ISPIWP#

SPI_MOSI

SPI_POWER

Pin

Definition

ISPIMISO

GND

SPI_CLK

SPI_POWER

35 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

Disable EEPROM

Connector type: 1x2 2-pin header, 2.54mm pitch

Connector location: JP8

1 2

Pin

Definition

EEPROM_WP

GND

HW Reset Function

Connector type: 1x2 2-pin header, 2.54mm pitch

Connector location: JP6

1 2

Pin

Definition

+3.3V

GND

36 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

Power Button

Connector type: 1x2 2-pin header, 2.54mm pitch

Connector location: JP5

1 2

Pin

Definition

+3.3VSBY

GND

4-Pin Power Connector

Connector type: 2x2 4-pin header

Connector location: CON3

Pin

Definition

GND

+12V

37 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

Pin

ATX Power Connector

Connector type: 2x12 24-pin header, 4.2mm pitch

Connector location: CON2

Definition

+3.3V

GND

+5VSBY

+12V

+3.3V

GND

+5V

Pin

Definition

+3.3V

+5V

PS_PWRGD

+12V

+3.3V

-12V

PSON# R

GND

-5V

+5V

GND

38 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

High Speed Board-to-Board Connector: Row A and B, Row C and D

Connector location: J8

Com Express A&B Connector

Com Express C&D Connector

Pin

A10

A11

A12

A13

Definition

GND(FIXED)

LAN_MDI3N

LAN_MDI3P

LAN_SPEED100#

LAN_SPEED1000#

LAN_MDI2N

LAN_MDI2P

LAN_LINK

LAN_MDI1N

LAN_MDI1P

GND(FIXED)

LAN_MDI0N

LAN_MDI0P

Pin

B10

B11

B12

B13

Definition

GND(FIXED)

LAN_ACTLED#

LPC_FRAME#

LPC_AD0

LPC_AD1

LPC_AD2

LPC_AD3

LPC_DRQ0#

LPC_DRQ1#

LPC_CLK

GND(FIXED)

PM_PWRBTN#

SMB_CLK

Pin

C10

C11

C12

C13

Definition

GND(FIXED)

ICH_IDE_DD7

ICH_IDE_DD6

ICH_IDE_DD3

ICH_IDE_DD15

ICH_IDE_DD8

ICH_IDE_DD9

ICH_IDE_DD2

ICH_IDE_DD13

ICH_IDE_DD1

GND(FIXED)

ICH_IDE_DD14

ICH_IDE_IORDY

Pin

D10

D11

D12

D13

Definition

GND(FIXED)

ICH_IDE_DD5

ICH_IDE_DD10

ICH_IDE_DD11

ICH_IDE_DD12

ICH_IDE_DD4

ICH_IDE_DD0

ICH_IDE_DDREQ

ICH_IDE_DIOW#

ICH_IDE_DDACK#

GND(FIXED)

ICH_IDE_IRQ

ICH_IDE_DA0

39 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

Pin

A34

A35

A36

A37

A38

A39

A40

A41

A24

A25

A26

A27

A28

A29

A30

A31

A32

A33

A14

A15

A16

A17

A18

A19

A20

A21

A22

A23

Definition

LAN_CTREF

PM_SLP_S3#

SATA_TXP0

SATA_TXN0

PM_SLP_S4#

SATA_RXP0

SATA_RXN0

GND(FIXED)

SATA_TXP2

SATA_TXN2

PM_SLP_S5#

SATA_RXP2

SATA_RXN2

PM_BATLOW#

ICH_SATA_LED#

HDA_SYNC

HDA_RST#

GND(FIXED)

HDA_BIT_CLK

HDA_SDOUT

BIOS_DIS0#

PM_THRMTRIP#

USB_6N

USB_6P

USB_OC67#

USB_4N

USB_4P

GND(FIXED)

Pin

B34

B35

B36

B37

B38

B39

B40

B41

B24

B25

B26

B27

B28

B29

B30

B31

B32

B33

B14

B15

B16

B17

B18

B19

B20

B21

B22

B23

Definition

SMB_DATA

SMB_ALERT#

SATA_TXP1

SATA_TXN1

SUS_STAT#

SATA_RXP1

SATA_RXN1

GND(FIXED)

SATA_TXP3

SATA_TXN3

PS_PWRGD

SATA_RXP3

SATA_RXN3

GAL_WDT#

HDA_SDIN2

HDA_SDIN1

HDA_SDIN0

GND(FIXED)

HDA_SPKR

I2C_CLK

I2C_DAT

PM_THRM#

USB_7N

USB_7P

USB_OC45#

USB_5N

USB_5P

GND(FIXED)

Pin

C34

C35

C36

C37

C38

C39

C40

C41

C24

C25

C26

C27

C28

C29

C30

C31

C32

C33

C14

C15

C16

C17

C18

C19

C20

C21

C22

C23

Definition

ICH_IDE_DIOR#

PCI_PME#

PCI_GNT#2

PCI_REQ#2

PCI_GNT#1

PCI_REQ#1

PCI_GNT#0

GND(FIXED)

PCI_REQ#0

ICH_PCI_RST#

ICH_PCI_AD0

ICH_PCI_AD2

ICH_PCI_AD4

ICH_PCI_AD6

ICH_PCI_AD8

ICH_PCI_AD10

ICH_PCI_AD12

GND(FIXED)

ICH_PCI_AD14

PCI_CBE#1

PCI_PERR#

PCI_LOCK#

PCI_DEVSEL#

PCI_IRDY#

PCI_CBE#2

ICH_PCI_AD17

ICH_PCI_AD19

GND(FIXED)

Pin

D34

D35

D36

D37

D38

D39

D40

D41

D24

D25

D26

D27

D28

D29

D30

D31

D32

D33

D14

D15

D16

D17

D18

D19

D20

D21

D22

D23

Definition

ICH_IDE_DA1

ICH_IDE_DA2

ICH_IDE_DCS1#

ICH_IDE_DCS3#

IDE_RST#

PCI_GNT#3

PCI_REQ#3

GND(FIXED)

ICH_PCI_AD1

ICH_PCI_AD3

ICH_PCI_AD5

ICH_PCI_AD7

PCI_CBE#0

ICH_PCI_AD9

ICH_PCI_AD11

ICH_PCI_AD13

ICH_PCI_AD15

GND(FIXED)

PCI_PAR

PCI_SERR#

PCI_STOP#

PCI_TRDY#

PCI_FRAME#

ICH_PCI_AD16

ICH_PCI_AD18

ICH_PCI_AD20

ICH_PCI_AD22

GND(FIXED)

ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

Pin

A62

A63

A64

A65

A66

A67

A68

A69

A57

A58

A59

A60

A61

A52

A53

A54

A55

A56

A42

A43

A44

A45

A46

A47

A48

A49

A50

A51

Definition

USB_2N

USB_2P

USB_OC23#

USB_0N

USB_0P

+VBAT

EXCD0_PERST#

EXCD0_CPPE#

INT_SERIRQ

GND(FIXED)

PCIE_TXP5

PCIE_TXN5

ICH_GPI0

PCIE_TXP4

PCIE_TXN4

GND(FIXED)

PCIE_TXP3

PCIE_TXN3

GND(FIXED)

PCIE_TXP2

PCIE_TXN2

ICH_GPI1

PCIE_TXP1

PCIE_TXN1

GND(FIXED)

ICH_GPI2

PCIE_TXP0

PCIE_TXN0

Pin

B62

B63

B64

B65

B66

B67

B68

B69

B57

B58

B59

B60

B61

B52

B53

B54

B55

B56

B42

B43

B44

B45

B46

B47

B48

B49

B50

B51

Definition

USB_3N

USB_3P

USB_OC01#

USB_1N

USB_1P

EXCD1_PERST#

EXCD1_CPPE#

HW_RST#

CB_RESET#

GND(FIXED)

PCIE_RXP5

PCIE_RXN5

ICH_GPO1

PCIE_RXP4

PCIE_RXN4

ICH_GPO2

PCIE_RXP3

PCIE_RXN3

GND(FIXED)

PCIE_RXP2

PCIE_RXN2

ICH_GPO3

PCIE_RXP1

PCIE_RXN1

PCIE_WAKE#

WAKE1#

PCIE_RXP0

PCIE_RXN0

Pin

C62

C63

C64

C65

C66

C67

C68

C69

C57

C58

C59

C60

C61

C52

C53

C54

C55

C56

C42

C43

C44

C45

C46

C47

C48

C49

C50

C51

Definition

ICH_PCI_AD21

ICH_PCI_AD23

PCI_CBE#3

ICH_PCI_AD25

ICH_PCI_AD27

ICH_PCI_AD29

ICH_PCI_AD31

PCI_IRQ#A

PCI_IRQ#B

GND(FIXED)

PEG_RXP0

PEG_RXN0

TYPE0#

PEG_RXP1

PEG_RXN1

TYPE1#

PEG_RXP2

PEG_RXN2

GND(FIXED)

PEG_RXP3

PEG_RXN3

PEG_RXP4

PEG_RXN4

PEG_RXP5

PEG_RXN5

Pin

D62

D63

D64

D65

D66

D67

D68

D69

D57

D58

D59

D60

D61

D52

D53

D54

D55

D56

D42

D43

D44

D45

D46

D47

D48

D49

D50

D51

Definition

ICH_PCI_AD24

ICH_PCI_AD26

ICH_PCI_AD28

ICH_PCI_AD30

PCI_IRQ#C

PCI_IRQ#D

PM_CLKRUN#

PCI_M66EN

CLK_PCI

GND(FIXED)

PEG_TXP0

PEG_TXN0

PEG_LANE_RV#

PEG_TXP1

PEG_TXN1

TYPE2#

PEG_TXP2

PEG_TXN2

GND(FIXED)

PEG_TXP3

PEG_TXN3

PEG_TXP4

PEG_TXN4

GND

PEG_TXP5

PEG_TXN5

ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

Pin

A90

A91

A92

A93

A94

A95

A96

A97

A80

A81

A82

A83

A84

A85

A86

A87

A88

A89

A70

A71

A72

A73

A74

A75

A76

A77

A78

A79

Definition

GND(FIXED)

LVDSA_DATA0

LVDSA_DATA#0

LVDSA_DATA1

LVDSA_DATA#1

LVDSA_DATA2

LVDSA_DATA#2

LVDS_VDD_EN

LVDSA_DATA3

LVDSA_DATA#3

GND(FIXED)

LVDSA_CLK

LVDSA_CLK#

LVDS_DDC_CLK

LVDS_DDC_DATA

ICH_GPI3

KBD_RST#

H_A20GATE

PCIE0_CK_REF+

PCIE0_CK_REF-

GND(FIXED)

SPI_POWER

SPI_MISO

ICH_GPO0

SPI_CLK

SPI_MOSI

GND(FIXED)

TYPE10#

Pin

B90

B91

B92

B93

B94

B95

B96

B97

B80

B81

B82

B83

B84

B85

B86

B87

B88

B89

B70

B71

B72

B73

B74

B75

B76

B77

B78

B79

Definition

GND(FIXED)

LVDSB_DATA0

LVDSB_DATA#0

LVDSB_DATA1

LVDSB_DATA#1

LVDSB_DATA2

LVDSB_DATA#2

LVDSB_DATA3

LVDSB_DATA#3

L_BKLT_EN

GND(FIXED)

LVDSB_CLK

LVDSB_CLK#

L_BKLT_CTRL

+5VSBY

BIOS_DIS1#

CRT_RED

GND(FIXED)

CRT_GREEN

CRT_BLUE

CRT_HSYNC

CRT_VSYNC

CRT_DDC_CLK_MCH

CRT_DDC_DATA_MCH

SPI_CS#

Pin

C90

C91

C92

C93

C94

C95

C96

C97

C80

C81

C82

C83

C84

C85

C86

C87

C88

C89

C70

C71

C72

C73

C74

C75

C76

C77

C78

C79

Definition

GND(FIXED)

PEG_RXP6

PEG_RXN6

SDVO_CTRLDATA

PEG_RXP7

PEG_RXN7

GND

PEG_RXP8

PEG_RXN8

GND(FIXED)

PEG_RXP9

PEG_RXN9

GND

PEG_RXP10

PEG_RXN10

GND

PEG_RXP11

PEG_RXN11

GND(FIXED)

PEG_RXP12

PEG_RXN12

GND

PEG_RXP13

PEG_RXN13

GND

Pin

D90

D91

D92

D93

D94

D95

D96

D97

D80

D81

D82

D83

D84

D85

D86

D87

D88

D89

D70

D71

D72

D73

D74

D75

D76

D77

D78

D79

Definition

GND(FIXED)

PEG_TXP6

PEG_TXN6

SDVO_CTRLCLK

PEG_TXP7

PEG_TXN7

GND

IDE_PATADET

PEG_TXP8

PEG_TXN8

GND(FIXED)

PEG_TXP9

PEG_TXN9

GND

PEG_TXP10

PEG_TXN10

GND

PEG_TXP11

PEG_TXN11

GND(FIXED)

PEG_TXP12

PEG_TXN12

GND

PEG_TXP13

PEG_TXN13

GND

PEG_ENABLE#

ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

Pin

A98

A99

A100

A101

A102

A103

A104

A105

A106

A107

A108

A109

A110

Definition

GND(FIXED)

+12V

GND(FIXED)

Pin

B98

B99

B100

B101

B102

B103

B104

B105

B106

B107

B108

B109

B110

Definition

CD1#_R

GND(FIXED)

+12V

GND(FIXED)

Pin

C98

C99

C100

C101

C102

C103

C104

C105

C106

C107

C108

C109

C110

Definition

PEG_RXP14

PEG_RXN14

GND(FIXED)

PEG_RXP15

PEG_RXN15

GND

+12V

GND(FIXED)

Pin

D98

D99

D100

D101

D102

D103

D104

D105

D106

D107

D108

D109

D110

Definition

PEG_TXP14

PEG_TXN14

GND(FIXED)

PEG_TXP15

PEG_TXN15

GND

+12V

GND(FIXED)

43 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

PCIe x16

Connector location: J9

Pin

A14

A15

A16

A17

A18

A10

A11

A12

A13

Definition

+12V

GND

+3.3V

CB_RESET#

GND

PCIE_X16_CLKP

PCIE_X16_CLKN

GND

PEG_RXP0

PEG_RXN0

GND

Pin

B14

B15

B16

B17

B18

B10

B11

B12

B13

Definition

+12V

GND

SMB_CLK

SMB_DATA

GND

+3.3V

GND

+3.3VSBY

PCIE_WAKE#

GND

PEG_TXP0

PEG_TXN0

GND

SDVO_CTRLCLK

GND

Pin

A32

A33

A34

A35

A36

A27

A28

A29

A30

A31

A19

A20

A21

A22

A23

A24

A25

A26

Definition

GND

PEG_RXP1

PEG_RXN1

GND

PEG_RXP2

PEG_RXN2

GND

PEG_RXP3

PEG_RXN3

GND

PEG_RXP4

PEG_RXN4

Pin

B32

B33

B34

B35

B36

B27

B28

B29

B30

B31

B19

B20

B21

B22

B23

B24

B25

B26

Definition

PEG_TXP1

PEG_TXN1

GND

PEG_TXP2

PEG_TXN2

GND

PEG_TXP3

PEG_TXN3

GND

SDVO_CTRLDATA

GND

PEG_TXP4

PEG_TXN4

GND

ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

Pin

A48

A49

A50

A51

A52

A43

A44

A45

A46

A47

A37

A38

A39

A40

A41

A42

A53

A54

A55

A56

A57

A58

A59

Definition

GND

PEG_RXP5

PEG_RXN5

GND

PEG_RXP6

PEG_RXN6

GND

PEG_RXP7

PEG_RXN7

GND

PEG_RXP8

PEG_RXN8

GND

PEG_RXP9

PEG_RXN9

GND

Pin

B48

B49

B50

B51

B52

B43

B44

B45

B46

B47

B37

B38

B39

B40

B41

B42

B53

B54

B55

B56

B57

B58

B59

Definition

PEG_TXP5

PEG_TXN5

GND

PEG_TXP6

PEG_TXN6

GND

PEG_TXP7

PEG_TXN7

GND

PEG_TXP8

PEG_TXN8

GND

PEG_TXP9

PEG_TXN9

GND

PEG_TXP10

PEG_TXN10

Pin

A71

A72

A73

A74

A75

A66

A67

A68

A69

A70

A60

A61

A62

A63

A64

A65

A76

A77

A78

A79

A80

A81

A82

Definition

PEG_RXP10

PEG_RXN10

GND

PEG_RXP11

PEG_RXN11

GND

PEG_RXP12

PEG_RXN12

GND

PEG_RXP13

PEG_RXN13

GND

PEG_RXP14

PEG_RXN14

GND

PEG_RXP15

PEG_RXN15

GND

Pin

B71

B72

B73

B74

B75

B66

B67

B68

B69

B70

B60

B61

B62

B63

B64

B65

B76

B77

B78

B79

B80

B81

B82

Definition

GND

PEG_TXP11

PEG_TXN11

GND

PEG_TXP12

PEG_TXN12

GND

PEG_TXP13

PEG_TXN13

GND

PEG_TXP14

PEG_TXN14

GND

PEG_TXP15

PEG_TXN15

GND

45 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

PCIe x4

Connector location: J10

Pin

A11

A12

A13

A14

A15

A16

Definition

GND

12V

GND

+3.3V

CB_RESET#

GND

PCIE_X4_CLKP

PCIE_X4_CLKN

GND

PCIE_RXP0

Pin

B10

B11

B12

B13

B14

B15

B16

Definition

12V

GND

SMB_CLK

SMB_DATA

GND

+3.3V

+3.3VSBY

PCIE_WAKE#

GND

PCIE_TXP0

PCIE_TXN0

GND

Pin

A25

A26

A27

A28

A29

A30

A31

A32

A17

A18

A19

A20

A21

A22

A23

A24

Definition

PCIE_RXN0

GND

PCIE_RXP1

PCIE_RXN1

GND

PCIE_RXP2

PCIE_RXN2

GND

PCIE_RXP3

PCIE_RXN3

GND

Pin

B25

B26

B27

B28

B29

B30

B31

B32

B17

B18

B19

B20

B21

B22

B23

B24

Definition

GND

PCIE_TXP1

PCIE_TXN1

GND

PCIE_TXP2

PCIE_TXN2

GND

PCIE_TXP3

PCIE_TXN3

GND

46 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

PCIe x1

Connector location: CON4

Pin

A12

A13

A14

A15

A16

A10

A11

A17

A18

Definition

+12V

GND

+3.3V

CB_RESET#

GND

PCIE_X1_CLKP0

PCIE_X1_CLKN0

GND

PCIE_RXP4

PCIE_RXN4

GND

Pin

B12

B13

B14

B15

B16

B10

B11

B17

B18

Definition

+12V

GND

SMB_CLK

SMB_DATA

GND

+3.3V

+3.3VSBY

PCIE_WAKE#

GND

PCIE_TXP4

PCIE_TXN4

GND

47 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

Mini-PCIe Slot (3G)

Connector location: CN10

1 2

51 52

Pin

Definition

PCIE_WAKE#

3VSB_MINI

GND

PCIE_X1_CLKN1

PCIE_X1_CLKP1

GND

PCIE_RXN5

PCIE_RXP5

Pin

Definition

3VSB_MINI

GND

1V5

UIM_PWR

UIM_DATA

UIM_CLK

UIM_RESET

UIM_VPP

GND

3VSB_MINI

CB_RESET#

3VSB_MINI

GND

Pin

Definition

GND

PCIE_TXN5

PCIE_TXP5

GND

3VSB_MINI

GND

Pin

Definition

1V5

SMB_CLK

SMB_DATA

GND

USB_4N

USB_4P

GND

1V5

GND

3VSB_MINI

ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

Mini-PCIe Slot (mSATA)

Connector location: CN8

1 2

51 52

Pin

Definition

GND

SATA_RXN3

SATA_RXP3

Pin

Definition

+3.3V

GND

1V5_MSATA

GND

+3.3V

GND

Pin

Definition

GND

SATA_TXN3

SATA_TXP3

GND

+3.3V

GND

TEST POINT

+3.3V

Pin

Definition

1V5_MSATA

SMBCLK_MAIN

SMBDATA_MAIN

GND

1V5_MSATA

GND

+3.3V

ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

SIM Card Slot

Connector location: CN9

C5 1

SATA Connectors

Connector type: Standard Serial ATAII 7P (1.27mm, SATA-M-180)

Connector location: CN6 and CN3

Pin

Definition

UIM_PWR

UIM_RESET

UIM_CLK

Pin

Definition

GND

UIM_VPP

UIM_DATA

CN6

Pin

CN3

Pin

Definition

GND

SATA_TXN0

SATA_RXN0

GND

Pin

Definition

GND

SATA_TXN1

SATA_RXN1

GND

Pin

Definition

SATA_TXP0

GND

SATA_RXP0

Definition

SATA_TXP1

GND

SATA_RXP1

ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

CFast Slot

Connector location: CN11

P17 S7

Pin

P11

P13

P15

P17

MH2

Definition

GND

SATA_TXN2

SATA_RXN2

GND

+3.3V

GND

Pin

P10

P12

P14

P16

MH1

Definition

SATA_TXP2

GND

SATA_RXP2

GND

TEST POINT

+3.3V

GND

51 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

CF-Master

Connector location: IDE1

Pin

Definition

GND

ICH_IDE_DD4

ICH_IDE_DD6

ICH_IDE_DCS1#

GND

+5V

GND

ICH_IDE_DA1

ICH_IDE_DD0

ICH_IDE_DD2

GND

Pin

Definition

ICH_IDE_DD3

ICH_IDE_DD5

GND

ICH_IDE_DA2

ICH_IDE_DA0

ICH_IDE_DD1

CD1#_R

Pin

Definition

ICH_IDE_DD11

ICH_IDE_DD13

ICH_IDE_DD15

ICH_IDE_DIOW#

ICH_IDE_IRQ

IDE_CABLE

IDE_RST#

GND

IDEACTP#

ICH_IDE_DD8

ICH_IDE_DD10

Pin

Definition

ICH_IDE_DD12

ICH_IDE_DD14

ICH_IDE_DCS3#

ICH_IDE_DIOR#

+5V

ICH_IDE_DDACK#

GND

ICH_IDE_DD9

GND

52 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

IDE-Slave

Connector type: 2x22 44-pin header, 2.0mm pitch

Connector location: CN1

Pin

Definition

IDE_RST#

ICH_IDE_DD7

ICH_IDE_DD6

ICH_IDE_DD5

ICH_IDE_DD4

ICH_IDE_DD3

ICH_IDE_DD2

ICH_IDE_DD1

ICH_IDE_DD0

GND

ICH_IDE_DDREQ

Pin

Definition

GND

ICH_IDE_DD8

ICH_IDE_DD9

ICH_IDE_DD10

ICH_IDE_DD11

ICH_IDE_DD12

ICH_IDE_DD13

ICH_IDE_DD14

ICH_IDE_DD15

GND

Pin

Definition

ICH_IDE_DIOW#

ICH_IDE_DIOR#

ICH_IDE_IORDY

ICH_IDE_DDACK#

ICH_IDE_IRQ

ICH_IDE_DA1

ICH_IDE_DA0

ICH_IDE_DCS1#

IDEACTP#

+5V

GND

Pin

Definition

GND

IDE_PATADET

ICH_IDE_DA2

ICH_IDE_DCS3#

GND

+5V

53 ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

PCI Slot

Connector location: J11

Pin

A10

A11

A12

A13

A14

A15

A16

A17

Definition

+12V

+5V

PCI_IRQ#A

PCI_IRQ#C

+5V

PCI_GNT#1

GND

+3.3VSBY

ICH_PCI_RST#

+5V

PCI_GNT#0

Pin

B10

B11

B12

B13

B14

B15

B16

B17

Definition

-12V

GND

+5V

PCI_IRQ#B

PCI_IRQ#D

PCI_REQ#1

GND

CLK_PCI_SIOT2

GND

CLK_PCI_SIOT1

GND

Pin

A26

A27

A28

A29

A30

A31

A32

A33

A34

A18

A19

A20

A21

A22

A23

A24

A25

Definition

GND

PCI_PME#

ICH_PCI_AD30

+3.3V

ICH_PCI_AD28

ICH_PCI_AD26

GND

ICH_PCI_AD24

ICH_PCI_AD20

+3.3V

ICH_PCI_AD22

ICH_PCI_AD20

GND

ICH_PCI_AD18

ICH_PCI_AD16

+3.3V

PCI_FRAME#

Pin

B26

B27

B28

B29

B30

B31

B32

B33

B34

B18

B19

B20

B21

B22

B23

B24

B25

Definition

PCI_REQ#0

+5V

ICH_PCI_AD31

ICH_PCI_AD29

GND

ICH_PCI_AD27

ICH_PCI_AD25

+3.3V

PCI_CBE#3

ICH_PCI_AD23

GND

ICH_PCI_AD21

ICH_PCI_AD19

+3.3V

ICH_PCI_AD17

PCI_CBE#2

GND

ICEK 268-T2 Starter Kit User Manual

Chapter 2: Jumpers and Connectors

Pin

A52

A53

A54

A55

A56

A45

A46

A47

A48

A49

A40

A41

A42

A43

A44

A35

A36

A37

A38

A39

A57

A58

A59

A60

A61

A62

Definition

GND

PCI_TRDY#

GND

PCI_STOP#

+3.3V

SMB_CLK

SMB_DATA

GND

PCI_PAR

ICH_PCI_AD15

+3.3V

ICH_PCI_AD13

ICH_PCI_AD11

GND

ICH_PCI_AD9

PCI_CBE#0

+3.3V

ICH_PCI_AD6

ICH_PCI_AD4

GND

ICH_PCI_AD2

ICH_PCI_AD0

+5V

+3.3V

+5V

Pin

B52

B53

B54

B55

B56

B45

B46

B47

B48

B49

B40

B41

B42

B43

B44

B35

B36

B37

B38

B39

B57

B58

B59

B60

B61

B62

Definition

PCI_IRDY#

+3.3V

PCI_DEVSEL#

GND

PCI_LOCK#

PCI_PERR#

+3.3V

PCI_SERR#

+3.3V

PCI_CBE#1

ICH_PCI_AD14

GND

ICH_PCI_AD12

ICH_PCI_AD10

PCI_M66EN

ICH_PCI_AD8

ICH_PCI_AD7

+3.3V

ICH_PCI_AD5

ICH_PCI_AD3

GND

ICH_PCI_AD1

+5V

+3.3V

+5V

55 ICEK 268-T2 Starter Kit User Manual

Chapter 3: System Setup

The starter kit is preconfigured and assembled. No addtional setup is required. However, if installation is needed, please refer to the instructions below.

1. Place the case on a stable surface and pull the yellow clasp to release the lock.

Setting up the System

Make sure the power supply is switched off and disconnected from the power sources to prevent electric shock or system damage before installing.

Clasp

56 ICEK 268-T2 Starter Kit User Manual

Chapter 3: System Setup

2. Open the case.

3. Align the mounting holes on the ICEB 8050C mainboard to the mounting holes inside the case.

ATX

Connector

Mounting holes

4. Tighten screws onto the holes to secure the mainboard, and plug the ATX power supply connector to the ATX connector on the motherboard.

ICEK 268-T2 Starter Kit User Manual

Chapter 3: System Setup

5. Locate the COM Express connector on the mainboard.

6. Install the ICES 268 module onto the COM Express connector.

Mounting holes

7. Align the mounting holes on the ICES 268 to the heatsink mounting holes on the mainboard.

ICEK 268-T2 Starter Kit User Manual

Chapter 3: System Setup

8. Once the holes are aligned, place the heatsink on top and tighten mounting screws to secure the heatsink.

10. Align the mounting holes on the LCD panel to the mounting holes on top of the case.

Mounting screws CFast card CFast slot

9. Insert the CFast card into the CFast slot.

Mounting holes

11. Tighten screws onto the mounting holes to secure the LCD panel.

59 ICEK 268-T2 Starter Kit User Manual

Chapter 3: System Setup

12. Connect the LVDS and CCFL cables to the LVDS and CCFL connector on the mainboard.

13. Plug the AC power cord to the power supply and connect the other end to a power outlet. Then switch on the system.

CCFL LVDS

AC Power

ICEK 268-T2 Starter Kit User Manual

Chapter 3: System Setup

There is a metal plate supporting the mainboard that can be lifted up or lowered down. The instructions below illustrate the step-by-step procedures.

NOTE: Before lifting up or lowering down, make sure the two spring-nuts located on the left and right side of the metal support plate are inserted/ closed to the end-position as depicted in the diagram below.

1. Hold on the left and right spring-nuts using both hands, and pull out the spring-nuts to lift up or lower down.

2. After lifting up the mainboard, make sure the two spring-nuts are inserted and closed to the end-position before plugging any connectors and I/O cards, then power on the system.

3. After lowering down the mainboard, make sure the two spring-nuts are inserted and closed to the end position before powering off the system and closing the cover.

Left spring-nut Right spring-nut

61 ICEK 268-T2 Starter Kit User Manual

Chapter 3: System Setup

External Soft-Power On/Off and Hardware Reset Switches

There are two special switches included inside the case to connect to JP5 and JP6 connectors for soft-power on/off and hardware reset function.

JP5: Soft-power on/off (red and black)

JP6: Hardware reset switch (green and black)

ICEK 268-T2 Starter Kit User Manual

Chapter 3: System Setup

Closing the Case

1. After lowering down the mainboard, make sure the two spring-nuts are inserted and closed to the end position before powering off.

2. Make sure to place the LCD cover protector onto the LCD panel before closing the case.

63 ICEK 268-T2 Starter Kit User Manual

Chapter 4: BIOS Setup

This chapter describes how to use the BIOS setup program for the

ICEK 268-T2. The BIOS screens provided in this chapter are for reference only and may change if the BIOS is updated in the future.

To check for the latest updates and revisions, visit the NEXCOM Web site at www.nexcom.com.tw.

About BIOS Setup

The BIOS (Basic Input and Output System) Setup program is a menu driven utility that enables you to make changes to the system configuration and tailor your system to suit your individual work needs. It is a ROM-based configuration utility that displays the system’s configuration status and provides you with a tool to set system parameters.

These parameters are stored in non-volatile battery-backed-up CMOS RAM that saves this information even when the power is turned off. When the system is turned back on, the system is configured with the values found in CMOS.

With easy-to-use pull down menus, you can configure such items as:

▪ Hard drives, diskette drives, and peripherals

▪ Video display type and display options

▪ Password protection from unauthorized use

▪ Power management features

The settings made in the setup program affect how the computer performs.

It is important, therefore, first to try to understand all the setup options, and second, to make settings appropriate for the way you use the computer.

When to Configure the BIOS

▪ This program should be executed under the following conditions:

▪ When changing the system configuration

▪ When a configuration error is detected by the system and you are prompted to make changes to the setup program

▪ When resetting the system clock

▪ When redefining the communication ports to prevent any conflicts

▪ When making changes to the Power Management configuration

▪ When changing the password or making other changes to the security setup

Normally, CMOS setup is needed when the system hardware is not consistent with the information contained in the CMOS RAM, whenever the CMOS

RAM has lost power, or the system features need to be changed.

64 ICEK 268-T2 Starter Kit User Manual

Chapter 4: BIOS Setup

Default Configuration

Most of the configuration settings are either predefined according to the Load Optimal Defaults settings which are stored in the BIOS or are automatically detected and configured without requiring any actions. There are a few settings that you may need to change depending on your system configuration.

Entering Setup

When the system is powered on, the BIOS will enter the Power-On Self

Test (POST) routines. These routines perform various diagnostic checks; if an error is encountered, the error will be reported in one of two different ways:

▪ If the error occurs before the display device is initialized, a series of beeps will be transmitted.

▪ If the error occurs after the display device is initialized, the screen will display the error message.

Legends

Key

Powering on the computer and immediately pressing <Del> allows you to enter Setup. Another way to enter Setup is to power on the computer and wait for the following message during the POST:

TO ENTER SETUP BEFORE BOOT PRESS

Ctrl

Alt

Press the key to enter Setup:

Function

Moves the highlight left or right to select a menu.

Moves the highlight up or down between sub¬menus or fields.

Exits the BIOS Setup Utility.

Scrolls forward through the values or options of the highlighted field.

Scrolls backward through the values or options of the highlighted field.

Selects a field.

Displays General Help.

Load previous values.

Load optimized default values.

Saves and exits the Setup program.

Press <Enter> to enter the highlighted sub¬menu

65 ICEK 268-T2 Starter Kit User Manual

Chapter 4: BIOS Setup

Scroll Bar

When a scroll bar appears to the right of the setup screen, it indicates that there are more available fields not shown on the screen. Use the up and down arrow keys to scroll through all the available fields.

Submenu

When “  ” appears on the left of a particular field, it indicates that a submenu which contains additional options are available for that field. To display the submenu, move the highlight to that field and press .

66 ICEK 268-T2 Starter Kit User Manual

Chapter 4: BIOS Setup

BIOS Setup Utility

Once you enter the AMI BIOS Setup Utility, the Main Menu will appear on the screen. The main menu allows you to select from several setup functions and one exit. Use arrow keys to select among the items and press to accept or enter the submenu.

Main

The Main menu is the first screen that you will see when you enter the BIOS

Setup Utility.

Main

Advanced Chipset Boot Security Save & Exit

Intel Reference Code version BIOS Information

BIOS Vendor

Core Version

Compliancy

Project Version

Build Date and Time

Memory Information

Memory Frequency

Total Memory

DIMM#0

DIMM#2

ME Firmware Information

ME FW Version

ME Firmware Mode

ME Firmware SKU

System Date

System Time

American Megatrends

4.6.5.3

UEFI 2.3; PI 1.2

I268-004

01/02/2013 11:15:17

1600 Mhz

16384 MB (DDR3)

8192 MB (DDR3)

8.0.0.1351

Normal Mode

5MB

[Tue 03 /05/2013]

[14:26:53]

→←: Select Screen

↑↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

System Date

The date format is <day>, <month>, <date>, <year>. Day displays a day, from Monday to Sunday. Month displays the month, from January to

December. Date displays the date, from 1 to 31. Year displays the year, from

1999 to 2099.

System Time

The time format is <hour>, <minute>, <second>. The time is based on the

24-hour military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to 23. Minute displays minutes from 00 to 59. Second displays seconds from 00 to 59.

67 ICEK 268-T2 Starter Kit User Manual

Chapter 4: BIOS Setup

Advanced

The Advanced menu allows you to configure your system for basic operation.

Some entries are defaults required by the system board, while others, if enabled, will improve the performance of your system or let you set some features according to your preference.

Setting incorrect field values may cause the system to malfunction.

Main

Advanced Chipset

ACPI Settings

RTC Wake Settings

CPU Configuration

SATA Configuration

AMT Configuration

USB Configuration

H/W Monitor

W83627DHG Super IO Configuration

CPU PPM Configuration

Boot Security Save & Exit

System ACPI Parameters

ACPI Settings

This section is used to configure ACPI Settings.

Main

Advanced Chipset PCIPnP Security Exit

ACPI Settings

Enable Hibernation

ACPI Sleep State

[Enabled]

[S3 only(Suspend to. . .)]

Enables or Disables System ability to Hibernate (OS/S4 Sleep

State). This option may be not effective with some OS.

→←: Select Screen

↑↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

→←: Select Screen

↑↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Enable Hibernation

Enables or disables system ability to hibernate (OS/S4 Sleep State). This option may not be effective with some OS.

ACPI Sleep State

Select the highest ACPI sleep state the system will enter when the suspend button is pressed.

68 ICEK 268-T2 Starter Kit User Manual

Chapter 4: BIOS Setup

RTC Wake Settings

This section is used to configure RTC Wake settings.

Advanced

Wake system with Fixed Time [Disabled] Enable or disable System wake on alarm event. When enabled, System will wake on the hr::min::sec specified

→←: Select Screen

↑↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Wake System with Fixed Time

Enables or disables system wake on alarm event. When enabled, system will wake on the hr::min::sec specified.

CPU Configuration

This section is used to configure the CPU.

Advanced

CPU Configuration

Intel(R) Core(TM) i5-3610ME CPU @ 2.70GHz

CPU Signature

Microcode Patch

CPU Speed

Processor Cores

Intel HT Technology

Intel VT-x Technology

Intel SMX Technology

64-bit

306a9

2700 MHz

Supported

Hyper-Threading

Intel Virtualization Technology

[Enabled]

[Disabled]

Enabled for Windows XP and

Linux (OS optimized for Hyper-

Threading Technology) and

Disabled for other OS (OS not optimized for Hyper-Threading

Technology). When Disabled only one thread per enabled core is enabled.

→←: Select Screen

↑↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Hyper-Threading

This field is used to enable or disable hyper-threading.

Intel ® Virtualization Technology

When this field is set to Enabled, the VMM can utilize the additional hardware capabilities provided by Vanderpool Technology.

69 ICEK 268-T2 Starter Kit User Manual

Chapter 4: BIOS Setup

SATA Configuration

This section is used to configure the SATA drives.

Advanced

SATA Controller(s)

SATA Mode Selection

Serial ATA Port 0

Software Preserve

Serial ATA Port 1

Software Preserve

Serial ATA Port 2

Software Preserve

Serial ATA Port 3

Software Preserve

[Enabled]

[IDE]

Hitachi HTE725 (250.0

SUPPORTED

Empty

Unknown

Empty

Unknown

Empty

Unknown

Enable or disable SATA Device.

→←: Select Screen

↑↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

SATA Controller(s)

Enables or disables the SATA controller.

SATA Mode Selection

Configures the SATA as IDE, AHCI or RAID mode.

IDE This option configures the Serial ATA drives as Parallel ATA physical storage device.

RAID This option allows you to create RAID or Intel Matrix Storage configuration on Serial ATA devices.

AHCI This option configures the Serial ATA drives to use AHCI

(Advanced Host Controller Interface). AHCI allows the storage driver to enable the advanced Serial ATA features which will increase storage performance.

70 ICEK 268-T2 Starter Kit User Manual

Chapter 4: BIOS Setup

AMT Configuration

This section is used to configure Active Management Technology (AMT) options.

Advanced

Intel AMT

BIOS Hotkey Pressed

MEBx Selection Screen

[Enabled]

[Disabled]

Enable/Disable Intel (R) Active

Management Technology BIOS

Extension.

Note : iAMT H/W is always enabled.

This option just controls the

BIOS extension execution.

If enabled, this requires additional firmware in the SPI device

→←: Select Screen

↑↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Intel ® AMT

Enables or disables Intel ® Active Management Technology.

BIOS Hotkey Pressed

Enables or disables BIOS hotkey press.

MEBx Selection Screen

Enables or disables MEBx selection screen.

USB Configuration

This section is used to configure the USB.

Advanced

USB Configuration

USB Devices:

1 Keyboard, 1 Mouse, 2 Hubs

Legacy USB Support

Port 60/64 Emulation

[Enabeld]

[Enabled]

Enables Legacy USB support.

AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.

→←: Select Screen

↑↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Legacy USB Support

Enable Enables Legacy USB.

Auto Disables support for Legacy when no USB devices are connected.

Disable Keeps USB devices available only for EFI applications.

Port 60/64 Emulation

Enables the 60h/64h I/O port emulation. You must enable this to fully support USB keyboard legacy for non-USB OSes.

71 ICEK 268-T2 Starter Kit User Manual

Chapter 4: BIOS Setup

H/W Monitor

This section is used to monitor hardware status such as temperature, fan speed and voltages.

Advanced

Pc Health Status cpu temperature

System temperature1

Fan1 Speed

VCORE

3.3V

: +30.75 C

: +40.125 C

: 4054 RPM

: +0.936 V

: +5.018 V

: +3.354 V

VCORE

Detects and displays the Vcore CPU voltage.

+5V

Detects and displays 5V voltage.

+3.3V

Detects and displays 3.3V voltage.

→←: Select Screen

↑↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

CPU Temperature

Detects and displays the current CPU temperature.

System Temperature1

Detects and displays the current system temperature.

Fan1 Speed

Detects and displays the speed of fan1.

72 ICEK 268-T2 Starter Kit User Manual

Chapter 4: BIOS Setup

W83627DHG Super IO Configuration

This section is used to configure serial ports 0 and 1, floppy disk and parallel port.

Advanced

W83627DHG Super IO Configuration

W83627DHG Super IO Chip



Floppy Disk Controller Configuration



Serial Port 0 Configuration

Serial Port 1 Configuration

Parallel Port Configuration

W83627DHG

Set Parameters of Floppy Disk

Controller (FDC)

Floppy Disk Controller Configuration

This section is used to configure the floppy disk controller.

Advanced

Enable or Disable Floppy Disk

Controller

Floppy Disk Controller Configuration

Floppy Disk Controller

Device Settings

[Enabled]

IO=3F0h; IRQ=6; DMA=2

Change Settings

Device Mode

[Auto]

[Read Write]

→←: Select Screen

↑↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

W83627DHG Super IO Chip

Displays the Super I/O chip used on the board.

→←: Select Screen

↑↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Serial Port

Enables or disables the floppy disk controller.

Change Settings

Selects an optimal setting for the Super IO device.

Device Mode

Changes the mode of the floppy disk controller. Select ‘Read Write’ for normal operation. Select ‘Write Protect’ mode for read only operation.

ICEK 268-T2 Starter Kit User Manual

Chapter 4: BIOS Setup

Serial Port 0 Configuration

This section is used to configure serial port 0.

Advanced

Serial Port 0 Configuration

Serial Port

Device Settings

Change Settings

[Enabled]

IO=3F8h; IRQ=4;

[Auto]

Enable or Disable Serial Port

(COM)

→←: Select Screen

↑↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Serial Port

Enables or disables the serial port.

Change Settings

Selects an optimal setting for the Super IO device.

Serial Port 1 Configuration

This section is used to configure serial port 1.

Advanced

Serial Port 1 Configuration

Serial Port

Device Settings

Change Settings

Device Mode

[Enabled]

IO=2F8h; IRQ=3;

[Auto]

[Standard Serial Po. . .]

Enable or Disable Serial Port

(COM)

→←: Select Screen

↑↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Serial Port

Enables or disables the serial port.

Change Settings

Selects an optimal setting for the Super IO device.

Device Mode

Changes the serial port mode.

ICEK 268-T2 Starter Kit User Manual

Chapter 4: BIOS Setup

Parallel Port Configuration

This section is used to configure the parallel port.

Advanced

Parallel Port Configuration

Parallel Port

Device Settings

Change Settings

Device Mode

[Enabled]

IO=378h; IRQ=5;

[Auto]

[STD Printer Mode]

Enable or Disable Parallel Port

(LPT/LPTE)

→←: Select Screen

↑↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Parallel Port

Enables or disables the parallel port.

Change Settings

Selects an optimal setting for the Super IO device.

Device Mode

Configures the operating mode of the parallel port.

CPU PPM Configuration

This section is used to configure the Processor Power Management (PPM) configuration.

Advanced

CPU PPM Configuration

EIST

CPU C3 Report

CPU C6 report

CPU C7 report

[Disabled]

Enable/Disable Intel SpeedStep

→←: Select Screen

↑↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

EIST

Enables or disables Intel ® SpeedStep.

CPU C3 Report

Enables or disables C3 report to the operating system.

CPU C6 Report

Enables or disables C6 report to the operating system.

CPU C7 Report

Enables or disables C7 report to the operating system.

ICEK 268-T2 Starter Kit User Manual

Chapter 4: BIOS Setup

Chipset

This section gives you functions to configure the system based on the specific features of the chipset. The chipset manages bus speeds and access to system memory resources.

Main

Advanced Chipset

PCH-IO Configuration

System Agent (SA) Configuration

Boot Security Save & Exit

PCH Parameters

→←: Select Screen

↑↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Setting incorrect field values may cause the system to malfunction.

PCH-IO Configuration

This section is used to configure PCH-IO configuration.

Main

Advanced Chipset Boot Security Save & Exit

1.5.0.0

QM77

04/C1

USB Configuration settings Intel PCH RC Version

Intel PCH SKU Name

Intel PCH Rev ID

USB Configuration

PCH Azalia Configuration

PCH LAN Controller

Wake on LAN

Restore AC Power Loss

RTC RAM Lock

[Enabled]

[Always ON]

[Enabled]

→←: Select Screen

↑↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

PCH LAN Controller

Enables or disables onboard NIC.

Wake on LAN

Enables or disables integrated LAN to wake the system.

Restore AC Power Loss

Select AC power state when power is re-applied after a power failure.

RTC RAM Lock

Enables or disables RTC RAM lock.

76 ICEK 268-T2 Starter Kit User Manual

Chapter 4: BIOS Setup

System Agent (SA) Configuration

►

Main

VT-d

Advanced Chipset Boot Security Save & Exit

Graphics Configuration

NB PCIe Configuration

[Enabled] Check to enable VT-d function on MCH.

→←: Select Screen

↑↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

VT-d

Enables or disables VT-d function on MCH.

Graphics Configuration

Configures the graphic chip settings.

NB PCIe Configuration

Configures the NB PCI Express settings.

Graphics Configuration

Main

Advanced Chipset Boot Security Save & Exit

Graphics Configuration

►

Primary Display

Internal Graphics

DVMT Total Gfx Mem

LCD Control

[Auto]

[256M]

Select which of IGFX/PEG/PCI

Graphics device should be Primary

→←: Select Screen

↑↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Primary Display

Select which of IGFX/PEG/PCI graphics device should be primary display or select SG for switchable Gfx.

Internal Graphics

Keep IGD enabled based on the setup options.

DVMT Total Gfx Mem

Select DVMT5.0 Total Graphic Memory size used by the Internal Graphics

Device.

ICEK 268-T2 Starter Kit User Manual

Chapter 4: BIOS Setup

NB PCIe Configuration

This section is used to configure Northbridge PCI Express settings.

Main

Advanced Chipset Boot Security Save & Exit

NB PCIe Configuration

PEG0

PEG - Gen X

Enable PEG x8 Gen2

[Auto]

[256M]

Configure PEG0 B0:D1:F0

Gen1-Gen3

→←: Select Screen

↑↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

PEG0 - Gen X

Configure PEG0 B0:D1:F0 Gen1-Gen3.

Enable PEG

Enables or disables the PEG slot.

78 ICEK 268-T2 Starter Kit User Manual

Chapter 4: BIOS Setup

Boot

This section is used to configure the boot features.

Main

Quiet Boot

Advanced Chipset Boot Security Save & Exit

Launch PXE OpROM policy

Boot Option Priorities

Boot Option #1

Hard Drive BBS Priorities

[Disabled]

[SATA PM: Hitachi . . .]

Enables or disables Quiet Boot option

→←: Select Screen

↑↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Quiet Boot

Enabled

Disabled

Displays OEM logo instead of the POST messages.

Displays normal POST messages.

Launch PXE OpROM Policy

Controls the execution of UEFI and legacy PXE OpROM.

Boot Option Priorities

Adjust the boot sequence of the system. Boot Option #1 is the first boot device that the system will boot from, next will be #2 and so forth.

Hard Drive BBS Priorities

Sets the order of the legacy devices in this group.

ICEK 268-T2 Starter Kit User Manual

Chapter 4: BIOS Setup

Security

Main

Advanced Chipset Boot Security Save & Exit

Set Administrator Password Password Description

If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup.

If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup the User Will have Administrator rights.

The password length must be in the following range:

Minimum length

Maximum length

Administrator Password

User Password

→←: Select Screen

↑↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Administrator Password

Select this to reconfigure the administrator’s password.

User Password

Select this to reconfigure the user’s password.

Save & Exit

Main

Advanced Chipset Boot Security Save & Exit

Save Changes and Reset

Discard Changes and Reset

Restore Defaults

Exit systm setup after saving the changes.

→←: Select Screen

↑↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Save Changes and Reset

To save the changes and reset, select this field then press <Enter>. A dialog box will appear. Confirm by selecting Yes.

Discard Changes and Reset

To exit the Setup utility and reboot the system without saving the changes, select this field then press <Enter>. You may be prompted to confirm again before exiting.

Restore Defaults

To restore the BIOS to default settings, select this field then press <Enter>. A dialog box will appear. Confirm by selecting Yes.

ICEK 268-T2 Starter Kit User Manual

Appendix A: Watchdog Timer

WDT Programming Guide

ICES 268 Watch Dog Function Configuration Sequence Description:

Start

Step1. See “SetupWDT” procedure

#Setup Watchdog Timer Environment

Step2. See “TimeBaseWDT” procedure

#Initial Watchdog Timer.

Users can select second or minute.

Step3. See “TimeCountWDT” procedure

#Set Watchdog Timer Time-out Value.

Users can set time-out value.

Step4: See ExitSetup procedure

#Exit Setup Environment

End

81 ICEK 268-T2 Starter Kit User Manual

Appendix A: Watchdog Timer

===============================================

SetupWDT PROC mov dx, 2eh mov al, 087h out dx, al nop nop out dx, al ;Write operations to special address port (2E) for entering MB PnP

Mode.

mov al, 07h out 2eh, al mov al, 08h ;Select logical device for Watch Dog.

out 2fh, al ret

SetupWDT ENDP

===============================================

TimeBaseWDT PROC mov al, 0F5h out 2eh, al mov al, 04h ; Here!! set 04h for second, set 0Ch for minute(WDT output through WDTO) out 2fh, al ret

TimeBaseWDT ENDP

===============================================

TimeCountWDT PROC mov al, 0F6h ;WDT Time-out register.

out 2eh, al mov al, 03h ;Here!! Set count 3.

out 2fh, al ret

TimeCountWDT ENDP

===============================================

ExitSetup PROC mov al, 0AAh out 2eh, al ret

ExitSetup ENDP

===============================================

82 ICEK 268-T2 Starter Kit User Manual

Industrial Computing Solutions

COM Express Type 2

ICEK 268-T2 (ICES 268 and ICEB 8050C)

Starter Kit User Manual

Contents

Preface

Chapter 1: Product Introduction

Chapter 2: Jumpers and Connectors

Chapter 3: System Setup

Chapter 4: BIOS Setup

Appendix A: Watchdog Timer

Related

ICEK 667-T6 Starter Kit User Manual

NEXCOM ICES 668 668-T6, ICES 668 3610ME, ICES 668 3615QE, ICES 668 3555LE, ICES 668 3517UE, ICEB 8060 8060 User Manual

NEXCOM ICES 673 User Manual

Industrial Motherboard NEX 981 User Manual

NEXCOM NET 300-ECM User Manual

NEXCOM EBC 550 User Manual | AI Chat & PDF Access

Embedded Computing NEX 609 User Manual

MS-9A69B1 Manual | AI Chat & PDF Download

MS-9A69U1 User Manual | AI Chat & PDF Download

NEXCOM NEX 890 User Manual

MSI MS-9A59 Industrial Data Machine | AI Chat & PDF Download

NEXCOM DNA 940 User Manual