NOTE:

Please read all instructions carefully before using this product

Table of Contents

Safety Notice

Hardware Pack

Assembly Instruction

Parts List

Resistance Chart

Warranty

Ordering Parts

Model

GS 99

Retain This

Manual for

Reference

Jan-14-05

OWNER'S

MANUAL

IBL

Marcy Platinum

Corner Gym

GS 99

IMPEX FITNESS PRODUCTS

14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746

Tel: (800) 999-8899 Fax: (626) 961-9966

www.impex-fitness.com [email protected]

TABLE OF CONTENTS

BEFORE YOU BEGIN...................................................................................... 1

IMPORTANT SAFETY NOTICES..................................................................... 2

HARDWARE PACK……….....…....................................................................... 3

ASSEMBLY INSTRUCTIONS...............................................................…..........6

PARTS LIST…………………………………………………………….……….…….25

RESISTANCE CHART………………………………………………………………. 26

WARRANTY.................................................................................................… 27

ORDERING PARTS......................................................................................... 27

BEFORE YOU BEGIN

Thank you for selecting the Marcy Platinum GS-99 CORNER GYM by IMPEX

FITNESS PRODUCTS. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction. If you have any questions, or find there are missing or damaged parts, we guarantee you complete satisfaction through direct assistance from our factory. To avoid unnecessary delays, please call our

TOLL-FREE customer service number . Our Customer Service Agents will provide immediate assistance to you.

Toll-Free Customer Service Number

1-800-999-8899

Mon. – Fri. 9 a.m. – 5 p.m. PST www.impex-fitness.com [email protected]

1

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions:

1. Keep children and pets away from the machine at all times. DO NOT

leave children unattended in the same room with the machine.

2. Only one person at a time should use the same station.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal

symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine

near water or outdoors.

5. Keep hands away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear

robes or other clothing that could become caught in the machine. Running

or aerobic shoes are also required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO

NOT use attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or

physician in attendance.

10. Before using the machine to exercise, always do stretching exercises to

properly warm up.

11. Never operate the machine if the machine is not functioning properly.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR

PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE

AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL

INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.

ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY

DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

2

HARDWARE PACK

3

HARDWARE PACK

4

HARDWARE PACK

5

ASSEMBLY INSTRUCTION

Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches

NOTE: It is strongly recommended two or people assembling this machine to avoid possible injury.

STEP 1 (See Diagram 1)

A.) Place the Right Base Frame (#1) on a flat surface. Make sure there is enough space around to assemble the machine.

B.) Insert four Guide Rods (#9) into the holes on the Right Base Frame (#1). Secure each Guide

Rod to the Right Base Frame from the bottom with a M10 x 1” Allen Bolt (#81).

C.) Slide four Ø 2 ½” x 1” Rubber Bumpers (#75) onto the Guide Rods.

Diagram 1

6

STEP 2 (See Diagram 2)

A.) Attach the Rear Vertical Frame (#4) to the Right Base Frame (#1). Attach the Left Base

Frame (#2) to the Rear Vertical Frame. Align the holes and secure them with two M10 x 2

¾” Carriage Bolts (#84),

∅

¾” Washers (#99), and M10 Aircraft Nuts (#96).

B.) Do not tighten the Nuts and Bolts yet.

DIAGRAM 2

7

STEP 3 (See Diagram 3)

A.) Attach the Right Vertical Beam (#3) to the Right Base Frame (#1). Secure it with two

M10 x 2 ½” Carriage Bolts (#85),

∅

¾” Washers (#99), and M10 Aircraft Nuts (#96). DO not tighten the Nuts and Bolts yet.

B.) Attach the Right Seat Support (#7) to the Right Vertical Beam (#3). Secure it with one

M10 x 2 ½” Carriage Bolt (#85), one M10 x 2 3/8” Allen Bolt (#83), one 3 1/8” x 1 ¾”

Bracket (#31), two Ø ¾” Washers (#99), and one M10 Aircraft Nut (#96).

C.) Attach the Right Seat Support (#7) to the Right Base Frame (#1). Secure it with one

M10 x 2 ½” Carriage Bolt (#85),

∅

¾” Washer (#99), and M10 Aircraft Nut (#96).

D.) Attach the Leg Developer (#19) to the bracket on the Right Seat Support (#7). Secure it with one M10 x 2 7/8” Allen Bolt (#79), two Ø ¾” Washers (#99), and one M10 Aircraft

Nut (#96). Do not over tighten the Leg Developer, make sure it is able to swivel.

DIAGRAM 3

8

STEP 4 (See Diagram 4)

A.) Slide fourteen Weight Plates (#44) onto the rear set of Guide Rods (#9). Make sure the groves on the Plates all face toward the back of the machine. Insert a Selector Rod (#29) into the center holes. Slide a Selector Stem (#45) onto the two Guide Rods.

B.) Repeat Procedure A above to install the other fourteen Weight Plates onto the other two

Guide Rods. Make sure the grove on the Plate all face toward the front of the machine.

C.) Place the Upper Frame (#6) onto the Right Vertical Beam (#3), Guide Rods (#9), and the

Rear Vertical Frame (#4).

D.) Secure the Upper Frame (#6) to the Right Vertical Beam (#3) with two M10 x 2 ½” Carriage

Bolts (#85), one 4 3/8” x 1 ¾” Bracket (#73), two Ø ¾” Washers (#99), and two M10 Aircraft

Nuts (#96).

E.) Secure the Upper Frame to each Guide Rod with one M10 x 1” Allen Bolt (#81) and Ø ¾”

Washer (#99).

F.) Attach the Left Vertical Beam (#5) to the Left Base Frame (#2). Secure it with two M10 x 2

½” Carriage Bolts (#85), Ø ¾” Washers (#99), and M10 Aircraft Nuts (#96).

G.) Secure the Left Vertical Beam (#5) to the Upper Frame (#6) and Rear Vertical Frame (#4) with two M10 x 2 ¾” Carriage Bolts (#84), Ø ¾” Washers (#99), and M10 Aircraft Nuts

(#96).

H.) DO NOT tighten all Nuts and Bolts yet.

9

DIAGRAM 4

10

STEP 5 (See Diagram 5)

A.) Attach the Left Seat Support (#8) to the Left Vertical Beam (#5). Secure it with two M10 x 2 ½”

Carriage Bolts (#85), one 4 3/8” x 1 ¾” Bracket (#73), two Ø ¾” Washers (#99), and two M10

Aircraft Nuts (#96).

B.) Attach the Left Seat Support (#8) to the Left Base Frame (#2). Secure it with a M10 x 2 ½”

Carriage Bolt (#85), Ø ¾” Washer (#99), and M10 Aircraft Nut (#96).

C.) Attach the Leg Press Frame (#14) to the Left Base Frame (#2). Secure it with one M12 x 3 ¾”

Hex Bolt (#89), two Ø1” Washers (#100), and one M12 Aircraft Nut (#97).

D.) Attach the Leg Press Adjustment Frame (#15) to the Leg Press Plate (#28). Secure it with one

M10 x 2 ½” Carriage Bolt (#85), Ø ¾” Washer (#99), and M10 Aircraft Nut (#96).

E.) Insert the Leg Press Adjustment Frame (#15) into the opening on the Leg Press Frame (#14).

Use a M18 Lock Knob (#61) to secure it at desired position.

11

STEP 6 (See Diagram 6)

A.) Attach the Front Press Base (#10) to the Right Base Frame (#1). Secure it with one M10 x 9

¼” Front Press Axle (#49), two Ø ¾” Washers (#99), and two M10 Aircraft Nuts (#96).

B.) Attach two Front Press Frames (#13) onto the bracket on the Front Press Base. Secure them to the Front Press Base with four M10 x 2 ½” Carriage Bolts (#85), Ø ¾” Washers (#99), and

M10 Aircraft Nuts (#96).

C.) Securely tighten all Nuts and Bolts previously installed.

12

STEP 7 (See Diagram 7)

A.) Attach the Butterfly Support Frame (#11) to the front of Right Vertical Frame (#3). Attach the Butterfly Pulley Support (#12) to the back of Right Vertical Frame. Align the holes and secure them with two M10 x 2 ½” Carriage Bolts (#85), Ø ¾” Washers (#99), and M10

Aircraft Nuts (#96).

B.) Attach two Swivel Pulley Brackets (#23) to the Butterfly Pulley Support (#12). Secure each

Bracket with one M12 x 4 3/8” Hex Bolt (#88), two Ø1” Washers (#100), and one M12

Aircraft Nut (#97). Do not over tighten the nut and bolt. The brackets need to swivel.

C.) Insert the Axle on the Right Butterfly (#18) through a Butterfly Adjustment Frame (#26) into the hole on the Butterfly Support Frame (#11). Secure it with one Ø1 ½” Washer (#101),

Lock Ring (#53), M6 x 1 ¼” Allen Bolt (#93), and M6 Aircraft Nut (#95).

D.) Thread a T-shaped Pull Pin (#58) through the hole on the Right Butterfly. Use the Pin to adjust the Butterfly position.

E.) Attach a Butterfly Arm Pad (#35) to the Right Butterfly. Secure it with two M8 x 2 3/8” Allen

Bolts (#91) and Ø 5/8” Washers (#98).

F.) Repeat procedures C, D and E above to install the Left Butterfly.

13

STEP 8 (See Diagram 8)

A.) Attach the Vertical Press Frame (#20) to the Rear Vertical Frame (#4). Secure it with one

M10 x 4 7/8” Vertical Press Axle (#48), two Ø ¾” Washers (#99), and two M10 x 5/8” Allen

Bolts (#80).

B.) Place the Vertical Press Frame rest against the rubber bumper on the Left Vertical Beam

(#5).

DIAGRAM 8

14

CABLE LOOP DIAGRAM

15

STEP 9 (See Cable Loop Diagram & Diagram 9)

A.) Attach the 108” Upper Cable (#37) to the front opening on the Upper Frame (#6). Attach a

Pulley (#56) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#83), two Pulley

Bushings (#55), and one M10 Aircraft Nut (#96). Draw the Cable towards the back of the machine. Note: Make sure the Ball Stopper is underneath the frame.

B.) Attach a Pulley to the bracket on the Upper Frame. Secure it with one M10x1 ¾” Allen Bolt

(#82), two

∅

¾” Washers (#99), one 2 7/8” L-shaped Pulley Bracket (#50), and one M10

Aircraft Nut (#96). Pull the Cable over the Pulley then downward. Install a Pulley to a Flat

Double Floating Pulley Bracket (#25). Let the bracket hanging for now.

C.) Draw the Cable around the Pulley then upward to the second open bracket on the Upper

Frame. Install another Pulley with a U-shaped Pulley Bracket (#51).

D.) Draw the Cable around the Pulley then downward to the Selector Rod (#29). Securely thread the end of the Cable through the Weight Selector Pin (#46) into the Selector Rod. Use the

Nut at the end of the Cable to tighten down the Bolt.

16

STEP 10 (See Cable Loop Diagram & Diagram 10)

A.) Clip one end of the 106” Butterfly Cable (#38) to the slot on the Left Butterfly Adjustment

Frame. Draw the Cable through the slot then to the open left Swivel Pulley Bracket (#23).

B.) Attach a Pulley (#56) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#82), two

∅

¾”

Washers (#99), and one M10 Aircraft Nut (#96).

C.) Draw the Cable around the Pulley then downward. Install a Pulley to the Angled Double

Floating Pulley Bracket (#24). Install another Pulley then let the Bracket hanging for now.

D.) Draw the Cable upward to the right Swivel Pulley Bracket. Install another Pulley.

E.) Draw the Cable to the Right Butterfly Adjustment Frame and secure the end of the cable to the slot.

DIAGRAM 10

17

STEP 11 (See Cable Loop Diagram & Diagram 11)

A.) Attach the 239” Front Press Cable (#36) to the lower opening on the Leg Developer (#19).

Attach a Pulley (#56) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#83), two

Pulley Bushings (#55), and one M10 Aircraft Nut (#96).

B.) Draw the Cable underneath the Pulley to the opening on the bottom of Right Seat Support

(#7). Attach a Pulley to the opening and secure it with one M10 x 1 ¾” Allen Bolt (#82), two Ø ¾” Washers (#99), and one M10 Aircraft Nut (#96).

C.) Draw the Cable underneath the Pulley then through the bottom opening on the Right

Vertical Beam (#3) to the second open bracket on the Right Base Frame (#1).

D.) Attach a Pulley to the second open bracket. Secure it with one M10 x 1 ¾” Allen Bolt

(#82), two

∅

¾” Washers (#99), and one M10 Aircraft Nut (#96).

E.) Draw the Cable around the Pulley then upward to the Flat Double Floating Pulley Bracket

(#25) previously installed in Step-9. Install a Pulley to the Bracket on the selected hole.

Note: After completing the entire cable installations, come back to this step and check the tightness of the cable loop system. If the cables are too loose, move up the pulley on the bracket. If the cables are too tight, move down the pulley on the bracket.

F.) Draw the Cable around the Pulley then down to the first open bracket on the Right Base

Frame (#1). Install a Pulley with a U-shaped Pulley Bracket (#51).

G.) Draw the Cable around the Pulley then upward to the Angled Double Floating Pulley

Bracket (#24) previously installed in Step-10. Install a Pulley to the selected hole on the

Bracket. Adjust the tension of the cables by changing the Pulley position on the Bracket.

H.) Draw the Cable around the Pulley then down to the open bracket on the back of Right

Vertical Beam (#3). Install a Pulley with a 2 7/8” L-shaped Pulley Bracket (#50).

I.) Draw the Cable through the opening on the Right Vertical Beam to the open bracket on the back of the Front Press Base (#10). Install a Pulley.

J.) Draw the Cable around the Pulley then back to the lower opening on the Right Vertical

Beam. Install a Pulley to the opening with one M10 x 2 3/8” Allen Bolt (#83), two Pulley

Bushings (#55), and one M10 Aircraft Nut (#96).

K.) Draw the Cable back to the opening on the Front Press Base. Install a Pulley to the opening with one M10 x 8 ¼” Allen Bolt (#87), two Ø ¾” Washers (#99), and one M10

Aircraft Nut (#96).

L.) Draw the Cable back to the open bracket welded on the lower Right Vertical Beam.

Secure the end of the Cable to the bracket with one M10 x 1” Allen Bolt (#81), two Ø ¾”

Washers (#99), and one M10 Aircraft Nut (#96).

18

DIAGRAM 11

19

STEP 12 (See Diagram 12)

A.) Attach end of the 357” Leg Press Cable (#39) to the bracket on the Left Seat Support

(#8). Secure the Cable to the bracket with one M10 x 1” Allen Bolt (#81), two Ø ¾”

Washers (#99), and one M10 Aircraft Nut (#96).

B.) Draw the Cable to the upper open bracket on the Leg Press Frame. Attach a Pulley to the bracket. Secure it with one M10 x 1 3/4” Allen Bolt (#82), two

∅

¾” Washers (#99), and one M10 Aircraft Nut (#96).

C.) Draw the Cable around the Pulley then to the open bracket on the Left Seat Support

(#8). Attach a Pulley to the opening. Secure it with one M10 x 1 ¾” Allen Bolt (#82), two

Ø ¾” Washers (#99), and one M10 Aircraft Nut (#96).

D.) Draw the Cable around the Pulley then back to the lower open bracket on the Leg Press

Frame. Repeat Procedure B above to install a Pulley.

E.) Draw the Cable around the Pulley then to the lower opening on the Left Seat Support.

Install another Pulley and secure it with one M10 x 2 3/8” Allen Bolt (#83), two Pulley

Bushings (#55), and one M10 Aircraft Nut (#96).

F.) Draw the Cable underneath the Pulley then through the bottom of Left Vertical Beam to the first open bracket on the Left Base Frame.

G.) Install a Pulley with one M10 x 1 ¾” Allen Bolt (#82), two

∅

¾” Washers (#99), and one

M10 Aircraft Nut (#96).

H.) Pull the Cable upward to the front opening on the Vertical Press Frame (#20). Install a

Pulley with one M10 x 5 ¾” Allen Bolt (#86), two Ø ¾” Washers (#99), and one M10

Aircraft Nut (#96).

I.) Draw the Cable around the Pulley then downward to the second open bracket on the

Left Base Frame. Repeat Procedure G above to install a Pulley.

J.) Pull the Cable upward to the back opening on the Vertical Press Frame. Repeat

Procedure H above to install a Pulley.

K.) Draw the Cable around the Pulley then downward to the third open bracket (angled) on the Left Base Frame. Repeat Procedure G above to install a Pulley.

L.) Pull the Cable upward and connect to the Short Chain (#77) with a C-clip (#78). Note:

After completing the entire Cable installations, check the tightness of the Cables, if the

Cables are too loose, shorten the Chain. If the Cables are too tight, lengthen the Chain.

M.) Connect the Chain to the 61”Vertical Press Cable (#40) with a M10 x 1” Allen Bolt (#81), two Ø ¾” Washers (#99), and one M10 Aircraft Nut (#96).

N.) Draw the Cable to the bracket on the top of Upper Frame (#6). Install two Small Pulleys

(#57) to the bracket with two 2 3/8” L-shaped Pulley Brackets (#52).

O.) Draw the Cable over the Small Pulleys then downward. Securely threaded it through the

Weight Selector Pin (#46) into the Selector Rod (#29).

P.) Use the Nut on the Bolt at the end of the Cable to securely tighten the Bolt to the

Selector Rod.

20

DIAGRAM 12

21

STEP 13 (See Diagram 13)

A.) Place a Seat Pad (#32) onto the Seat Incline Adjustment (#16). Secure it with two M8 x 1 5/8”

Allen Bolts (#92) and Ø 5/8” Washers (#98).

B.) Insert the Seat Incline Adjustment into the opening on the Left Seat Support. Secure it with a

M18 Lock Knob (#61) at desired position.

C.) Attach a Backrest Board (#33) to the Left Vertical Beam (#5). Secure it with two M8 x 2 3/8”

Allen Bolts (#91) and

∅

5/8” Washers (#98).

DIAGRAM 13

22

STEP 14 (See Diagram 14)

A.) Place a Seat Pad (#32) onto the Right Seat Support (#7). Secure it with two M8 x 2 3/8” Allen

Bolts (#91) and

∅

5/8” Washers (#98).

B.) Attach a Backrest Board (#33) to the Right Vertical Beam (#3). Secure it with two M8 x 2 3/8”

Allen Bolts (#91) and

∅

5/8” Washers (#98).

C.) Insert two Foam Roll Tubes (#41) halfway through the holes on the Right Seat Support (#7) and Leg Developer (#19). Push four Foam Rolls (#47) onto the Tubes from both sides. Plug four Foam Roll End Caps (#62) into the ends.

D.) Attach the Arm Curl Pad (#34) to the Arm Curl Stand (#21). Secure it with two M8 x 5/8” Allen

Bolts (#90) and

∅

5/8” Washers (#98). Insert the Arm Curl Stand into the opening in front of the seat. Use the M18 Lock Knob (#61) to secure the desired position.

E.) Connect the Lat Bar (#22) to the Upper Cable with two C-clips (#78) and a Short Chain (#77).

F.) Connect the Arm Curl Handle (#42) to the Front Press Cable (#36) with two C-clips (#78) and a Long Chain (#104).

23

STEP 15 (See Diagram 15)

A.) Securely tighten all the nuts and bolts previously installed.

B.) To maximize the performance of the gym, it is recommended to use light lubricant such as

WD-40 on the two chromed rods which the weight plates slide up and down to minimum frictions.

C.) Attach four Weight Stack Covers (#30) to the machine and secure each Weight Stack Cover with two M10 x 5/8” Allen Bolts (#80) and

∅

3/4” Washers (#99).

DIAGRAM 15

24

PARTS LIST

KEY NO.

1

2

3

4

5

DESCRIPTION

Right Base Frame

Left Base Frame

Right Vertical Beam

Rear Vertical Frame

Left Vertical Beam

Q’ty

1

1

1

1

1

1

1

1

4

7

8

9

10

11

12

13

14

15

16

Right Seat Support

Left Seat Support

Guide Rod

Front Press Base

Butterfly Support Frame

Butterfly Pulley Support

Front Press Frame

Leg Press Frame

Leg Press Adjustment Frame

Seat Incline Adjustment

1

1

1

2

1

1

1

1

1

1

20

21

23

24

25

26

27

28

30

31

34

35

36

37

38

39

40

42

43

46

Vertical Press Frame

Arm Curl Stand

1

1

Swivel Pulley Bracket

1

2

Angled Double Floating Pulley Bracket 1

Flat Double Floating Pulley Bracket

Butterfly Adjustment Frame

Ø1 ½” x 7/8” Bushing

Leg Press Plate

1

2

8

1

2

Weight Stack Cover

3 1/8” x 1 ¾” Bracket

Arm Curl Pad

Butterfly Arm Pad

239” Front Press Cable

108” Upper Cable

106” Butterfly Cable

357” Leg Press Cable

1

2

1

1

4

1

2

2

1

1

61” Vertical Press Cable

Arm Curl Handle

Arm Curl Handle Tube

Weight Selector Pin

1

2

1

1

28

2

2

4

1

1

48

49

M10 x 4 7/8” Vertical Press Axle

M10 x 9 ¼” Front Press Axle

50 2 7/8” L-shaped Pulley Bracket

51 U-shaped Pulley Bracket

52 2 3/8” L-shaped Pulley Bracket

53 Lock Ring

2

2

2

2

54 1 5/8” Rubber Bumper

55 Pulley Bushing

56 Pulley

57 Small Pulley

58 T-shaped Pull Pin Set

59 2” Sleeve

60 1 ¾” Sleeve

61 M18 Lock Knob

62 Foam Roll End Cap

63 2” x 1” End Cap

64 1” Square End Cap

65 1 ½” Square End Cap

66 1 7/8” Square End Cap

67 Handle Grip

68 Lat Bar Grip

69 Ø 1 ½” x 1” Bushing

70 Ø 1” x Ø ½” Bushing

71

∅

1” x Ø 7/8” Bushing

72 Ø ¾” x Ø 3/8” Bushing

73 4 3/8” x 1 ¾” Bracket

74 Ø 1 7/8” x 1 5/8” Rubber Bumper

75 Ø 2 ½” x 1” Rubber Bumper

76 Ø 1 ½” x 5/8” Rubber Bumper

77 Short Chain

78 C-clip

79 M10 x 2 7/8” Allen Bolt

80 M10 x 5/8” Allen Bolt

81 M10 x 1” Allen Bolt

82 M10 x 1 ¾” Allen Bolt

83 M10 x 2 3/8” Allen Bolt

84 M10 x 2 ¾” Carriage Bolt

85 M10 x 2 ½” Carriage Bolt

86 M10 x 5 ¾” Allen Bolt

87 M10 x 8 ¼” Allen Bolt

88 M12 x 4 3/8” Hex Bolt

89 M12 x 3 ¾” Hex Bolt

90 M8 x 5/8” Allen Bolt

91 M8 x 2 3/8” Allen Bolt

92 M8 x 1 5/8” Allen Bolt

93 M6 x 1 ¼” Allen Bolt

94 M6 x 5/8” Philips Screw

95 M6 Aircraft Nut

96 M10 Aircraft Nut

97 M12 Aircraft Nut

98 Ø 5/8” Washer

99 Ø ¾” Washer

100 Ø 1” Washer

101 Ø 1 ½” Washer

102 Ankle Strap

Chain

105 Ø1” Cone-shaped End Cap

#6 Allen Wrench (Tool)

#5 Allen Wrench (Tool)

25

1

2

1

2

5

4

18

2

10

2

2

4

1

2

5

1

10

11

21

2

2

2

4

3

16

6

12

2

2

2

3

2

56

3

14

99

6

2

1

1

1

2

1

1

2

2

1

3

4

4

1

8

26

2

GS 99 WEIGHT RESISTANCE CHART

WEIGHT PLATE

Station 1 2 3 4 5 6 7

Low 35 45 55 65 75 85 95

Butterfly

15 25 35 45 55 65 75

10 17 24 31 38 45 52

Front Press

60 80 100 120 140 160 180

35 50 65 80 95 110 125

WEIGHT PLATE

Station 8 9 10 11 12 13 14

Low 105 115 125 135 145 155 165

85 95 105 115 125 135 145

87 101

Leg 200 220 240 260 280 300 320

Front 140 155 170 185 200 215 230

*Number s are approximate. Actual weight may vary.

26

4.

IMPEX INC.

LIMITED WARRANTY

IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this

Warranty is limited to replacing or repairing, at IMPEX's option.

All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling

IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to

IMPEX must be prepaid by the customer. This warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for products used for commercial or rental purposes. No other warranty beyond that specifically set forth above is authorized by IMPEX.

IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential damages or whatsoever natures. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.

The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation may not apply to you.

This warranty gives you specific legal right. You may also have other rights which vary from state to state.

IMPEX INC.

14777 Don Julian

City of Industry, CA 91746

ORDERING REPLACEMENT PARTS

Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-

999-8899 during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time. www.impex-fitness.com [email protected]

When ordering replacement parts, always give the following information.

1. Model

2. Description of Parts

Date of Purchase

27