KI WorkZone Assembly Instructions Manual

Assembly Instructions
WorkZone® Desking System
November 2012
WorkZone® Basic Worksurface
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Tools Required
• Phillips Screwdriver
• Level
1. To avoid scratching the
worksurface, place the top face
down onto a soft protective
surface.
2. Attach two leg sets to
worksurface bottom by
aligning legs to pre-drilled
holes and inserting three
#12 x 13/4” screws per leg set
(Figure 1).
Note: In the instance where
a worksurface is to be paired
with a transitional unit, a leg
set with a short transitional
foot (not shown) will be
assembled to the end of
the worksurface where the
transitional unit is to be
attached. Refer to your
space-planning layout.
Important: Worksurfaces are
assembled upside-down, so
will be in reverse orientation
as compared to your
space-planning layout.
2
Figure 1
WorkZone® Basic Worksurface
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
sic Worksurface / Printer Stand
anel between leg sets.
l wireway is to be
ce the wireway
lange of modesty
surface, aligning the
llustrated. Insert two
per left and right side
to leg. Do not tighten
1).
3. Align modesty panel between
leg sets. If optional horizontal
wireway is to be installed to
unit, place the wireway between
mounting flange of modesty panel
and the worksurface, aligning the
mounting holes as illustrated.
Insert two #10 x ½” screws per
left and right side of modesty
panel into leg. Do not tighten at
this time (Figure 1).
he worksurface right
wo leg plugs into the
at the outside of each
d (Figure 2).
vertical wireway
with non-powered
l wireway - inner”
is to be installed
the table. The
uter” (no cut-out) is
e outside of a leg
worksurface
grommet cover
leg plug
s fasten into each
e of the leg set
be oriented to press
positioning an outer
o-cut-out), to the
et as illustrated. Next
ertical wireway cover
e correct orientation at
set and press it into
Figure 2).
rface by turning the
es either in or out. The
he glides and the
ets must be tightened
om of the leg to secure
ce grommet cover into
orksurface top
vertical
wireway - inner
leg set
vertical
wireway - outer
Figure 2
Figure 2
adjustable
glide
4. Carefully stand the worksurface
right side up and install two leg
plugs into the two exposed holes
at the outside of each leg set as
illustrated (Figure 2).
Note: Two different vertical
wireway halves are supplied with
non-powered tables: The “vertical
wireway - inner” (with two
cut-outs) is to be installed
facing the inside of the table.
The “vertical wireway-outer” (no
cut-out) is to be installed on the
outside of a leg (Figure 2).
5. Vertical wireways fasten into
each other from each side of
the leg set opening and must
be oriented to press together.
Begin by positioning an outer
vertical wireway (no-cut-out),
to the outside of the leg set as
illustrated. Next position the inner
vertical wireway cover (two
cut-outs) in the correct
orientation at the inside of the
leg set and press it into the outer
wireway (Figure 2).
6. Level the worksurface by turning
the four adjustable glides either
in or out. The jambnuts between
the glides and the bottom of the
leg sets must be tightened up
against the bottom of the leg to
secure the glide (Figure 2).
7. Press worksurface grommets into
wireway holes in worksurface top
(Figure 2).
3
WorkZone® Starter/Adder/Finisher Worksurface
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
the illustrated location, in the
set of three mounting holes
using three #12 x 1 3/4” screws
(Figure 1).
Note: Starter/finisher modesty
panels are longer than
standard WorkZone modesty
panels, and are shorter than
adder modesty panels.
Tools Required
• Phillips Screwdriver
• Level
Starter Worksurface
Note: The starter worksurface
is assembled upside down,
and when turned upright after
full-assembly, it will be the
right-hand most worksurface
as the user sits at it.
1. Begin assembly by installing
two shared-leg brackets to a
transitional leg set (leg with
shorter foot). Use three
#10 x ½” screws per bracket to
secure (Figure 1).
2. To avoid scratching top,
carefully lay worksurface
upside down on a soft,
protective surface. Install
the transitional leg set
to the underside of the
worksurface at pre-drilled
holes using four #12 x 1”
screws. The transitional leg
will be “shared” so should
be installed to the mounting
holes closest to the edge of
the worksurface such that the
center line of the leg is directly
over the end of the table
(Figure 1).
3. Install the standard leg set to
the underside of the table at
4
4. Set a starter/finisher modesty
panel between the two installed
legs over mounting holes in
worksurface as illustrated. If
optional horizontal wireway
is to be installed to unit,
place the wireway between
mounting flange of modesty
panel and the worksurface,
aligning the mounting holes
as illustrated. Secure modesty
panel to worksurface with three
#12 x 1” screws, and attach
modesty panel ends to the legs
using two #10 x ½” screws at
each leg (Figure 1).
Starter/Adder/Finisher Worksurface Assem
standard
leg set
starter/finisher
modesty panel
(shorter length)
#12 x 1”
screw
#12 xx 1133//44””
#12
screw
screw
#10 x ½”
screws
transitional leg set
(shorter foot)
#12 x 1”
screw
shared-leg
bracket
horizontal
wireway
(optional)
starter
worksurface
shared-leg
bracket
Figure
Starter
Worksurface
Figure 11- -Starter
Worksurface
#10 x ½”
screw
WorkZone® Starter/Adder/Finisher Worksurface
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Adder Worksurface
Note: The adder worksurface
is assembled upside down, and
when turned upright after full
assembly, it will attach to the
worksurface to its right (either
starter or adder as the user sits
at it).
Starter/Adder/Finisher Worksurface Assemb
adder
modesty panel
(longer)
transitional leg set
(shorter foot)
#10 x ½”
screw
#12 x 1”
screws
horizontal
wireway
(optional)
adder
worksurface
Figure Figure
2 - Adder
Worksurface
2 - Adder
Worksurface
shared-leg
bracket
5. As in step 1, Figure 1 earlier,
Adder Worksurface
begin assembly by installing
Note: The adder worksurface is assembled
two shared-leg brackets to a
upside down, and when turned upright after
transitional leg set (leg with
full assembly, it will attach to the worksurfac
shorter foot). Use three
to its right (either starter or adder as the use
#10 x ½” screws per bracket to
sits at it).
secure (Figure 1).
5. As in step 1, Figure 1 earlier, begin
6. To avoid scratching top, carefully
assembly by installing two shared-leg
lay adder worksurface upside
brackets to a transitional leg set (leg with
down on a soft, protective
shorter foot). Use three #10 x ½” screws p
surface. Install the transitional
bracket to secure (Figure 1).
leg set to the underside of the
worksurface at pre-drilled holes
6. To avoid scratching top, carefully lay add
using four #12 x 1” screws.
worksurface upside down on a soft,
The transitional leg set will be
protective surface. Install the transitional leg
“shared” so should be installed
set to the underside of the worksurface at
to the mounting holes closest to
pre-drilled holes using four #12 x 1” screw
the edge of the worksurface such
The transitional leg set will be “shared” so
that the centerline of the leg is
should be installed to the mounting holes
directly over the end of the table
closest to the edge of the worksurface such
(Figure 2).
that the centerline of the leg is directly over
the end of the table (Figure 2).
Note: Adder modesty panels are
“starter”panels
modesty
Note:longer
Adderthan
modesty
are longer than
panels.
“starter” modesty panels.
Positionan
anadder
adder modesty
modesty over the
7.7.Position
over
the
mounting
holes in and next to
mounting holes in worksurface,
worksurface,leg
andasnext
to the If optional
the transitional
illustrated.
transitional
leg
as
illustrated.
horizontal wireway is to be installed to unit,
optional
horizontal
wireway
placeIf the
wireway
between
mounting flange
is to be installed
to the
unit,worksurface,
place
of modesty
panel and
the wireway
betweenholes
mounting
aligning
the mounting
as illustrated.
flange
of
modesty
panel
and
Secure modesty panel to worksurface
with
worksurface,
aligning
threethe
#12
x 1” screws,
andthe
attach one
mounting
modesty
panelholes
end as
to illustrated.
the transitional leg
Secure
modesty
panel
to (Figure 2).
using two #10 x ½” screws
worksurface with three #12 x 1”
screws, and attach one modesty
panel end to the transitional
leg using two #10 x ½” screws
(Figure 2).
5
WorkZone® Starter/Adder/Finisher Worksurface
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Finisher Worksurface
Note: The finisher worksurface
is assembled upside down,
and when turned upright after
full-assembly, it will attach to an
adder worksurface.
8. To avoid scratching top, carefully
lay finisher worksurface upside
down on a soft, protective
surface. Install a standard leg
set to the underside of the
worksurface at pre-drilled
holes using three #12 x 13/4”
screws. The standard leg set
is “not shared” so should not
be installed to the mounting
holes closest to the edge of the
worksurface (Figure 3).
Note: Starter/finisher modesty
panels are longer than standard
WorkZone modesty panels, and
are shorter than adder modesty
panels.
9. Position a starter/finisher
modesty panel over the
mounting holes in the
worksurface, and next to the
standard leg as illustrated. If
optional horizontal wireway is
to be installed to unit, place
the wireway between mounting
flange of modesty panel and
the worksurface, aligning the
mounting holes as illustrated.
Secure modesty panel to
worksurface with three
#12 x 1” screws, and attach
one modesty panel end to the
standard leg using two
#10 x ½” screws (Figure 3).
Starter/Adder Assembly
10. Carefullly turn the starter
worksurface assembly to the
upright position. With care,
turn the adder worksurface
assembly upright, next to the
starter unit and set the no-leg
end of the adder surface onto
the shared-leg bracket of the
starter worksurface assembly
(Figure 4).
11. Twist in four #12 x 1” screws
starter/finisher
through the
shared-leg bracket
modesty panel
of the starter
worksurface,
(shorter
length) and
into the pre-drilled mounting
holes at the underside of
the adder worksurface as
horizontal
illustrated. Do not tighten
wireway
screws completely at this
time
(optional)
(Figure 4).
#12 x 1”
screw
#10 x ½”
screws
starter/finisher
modesty panel
(shorter length)
standard
#12 x 1” leg set
screw
#10 x ½”
screws
horizontal
wireway
(optional)
12. Twist in two #10 x ½” screws
through the side of the adder
modesty panel and into the leg
of the starter worksurface, but
do not tighten screws at this
time (Figure 4).
finisher
worksurface
Note: any number of
additional adder worksurfaces
can be attached to existing
adder worksurfaces following
the steps above.
finisher
worksurface
#12 x
screw
#12 x
screw
Figure 3 - Finisher Worksurface
adder
worksurface
assembly
#10 x ½”
screw
adder
worksurface
assembly
transitional leg set
(shorter foot)
adder
modesty panel
(longer)
#10 x ½”
screw
adder
modesty panel
(longer)
shared-leg
bracket
transitional leg set
(shorter foot)
#12 x 1”
shared-leg
bracket
starter
worksurface
assembly
starter
worksurface
assembly
screw
#12 x 1”
screw
transitional leg set
(shorter foot)
standard
leg set
transitional leg set
(shorter foot)
Figure 4 - Adder to Starter Assembly
6
standard
leg set
standard
leg set
WorkZone®
11.Carefullly turn the finisher
worksurface assembly to the upright
position and set the no-leg end of the
Starter/Adder/Finisher
adder surface onto Worksurface
the shared-leg
Instructions
bracket of theAssembly
adder worksurface
assembly (Figure 5).
12. Twist in four #12 x 1” screws
through the shared-leg bracket of the
Assemble units as described herein only. To do otherwise
adder worksurface, and into the premay result in instability. All screws, nuts and bolts must be
drilled mounting holes at the underside of
tightened securely and must be checked periodically after
the finisher worksurface as illustrated.
assembly. Failure to assemble properly, or to secure parts
Do not tighten screws completely at this
may result in assembly failure and personal injury.
time (Figure 5).
13. Twist in two #10 x ½” screws
through the side of the adder modesty
panel and into the leg of the starter
worksurface, but do not tighten screws
at this time (Figure 5).
finisher
worksurface
assembly
14. Align the run of adjoining tables to
their final location and twist leveling
glides in or out to level worksurfaces
properly. The jambnuts between the
glides and the bottom of the leg sets
must be tightened up against the bottom
of the leg to secure the glide. At this time,
tighten all screws attaching modesty
panels to legs and shared-leg brackets to
worksurfaces (Figure 5).
#10 x ½”
screw
standard
leg set
finisher
modesty panel
shared-leg
bracket
adjustable
glides
adder
worksurface
assembly
#12 x 1”
screw
adjustable
glides
starter
worksurface
assembly
Figure
5 - Finisher
to Adder/Starter
Assembly
Figure
5 - Finisher
to Adder/Starter
Assembly
transitional leg set
(shorter foot)
Finisher to Starter/Adder
15. Twist in two #10 x ½” screws
Assembly
through the side of the adder
13. Carefullly turn the finisher
modesty panel and into the leg
worksurface assembly to the
of the starter worksurface, but do
upright
position
and
set
the
not tighten screws at this time
Figure 5- Finisher to Adder/Starter Assembly
no-leg end of the adder surface
(Figure 5).
onto the shared-leg bracket of
the adder worksurface assembly
16. Align the run of adjoining tables
(Figure 5).
to their final location and twist
leveling glides in or out to level
14. Twist in four #12 x 1” screws
worksurfaces properly. The
through the shared-leg bracket
jambnuts between the glides
of the adder worksurface, and
and the bottom of the leg sets
into the pre-drilled mounting
must be tightened up against
holes at the underside of
the bottom of the leg to secure
the finisher worksurface as
the glide. At this time, tighten all
illustrated. Do not tighten
screws attaching modesty panels
screws completely at this time
to legs and shared-leg brackets
(Figure 5).
to worksurfaces
(Figure 5).
standard
leg set
7
WorkZone® Starter/Adder/Finisher Worksurface
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Starter/Adder/Finisher Worksurface Assembly
15. Install a vertical wireway into each leg
Install
a vertical wireway
intowireway
set 17.
by first
positioning
the outer
leg set by first
section each
as illustrated.
The positioning
extended face
the outermust
wireway
of the wireway
be section
orientedasup so as
The extended
face ofof the
to coverillustrated.
the table-support
member
the wireway
mustIncorrectly
be oriented up
leg set when
installed.
soitaswill
to cover
installed,
coverthe
thetable-support
foot member.
of the legslightly
set when
Flex themember
outer wireway
and press
installed.
Incorrectly
it
it into place
between
the leginstalled,
uprights.
will cover
footwireway
member.cover
Flex as
Next position
the the
inner
theand
outerpress
wireway
slightly
illustrated
it into
placeand
in the
it into
place between
the
vertical press
wireway
(Figure
3).
leg uprights. Next position the
inner
wireway cover
as illustrated
16. Press
worksurface
grommet
cover
and press
it into
place in the top,
into wireway
holes
in worksurface
vertical
(Figure
6). two
and install
two wireway
leg plugs
into the
exposed holes at the outside of each leg
Press worksurface
into
set 18.
as illustrated
(Figure grommets
6).
wireway holes in worksurface
top, and install two leg plugs
into the two exposed holes at
the outside of each leg set as
illustrated (Figure 6).
worksurface
grommet cover
leg plug
vertical
wireway - inner
leg set
vertical
wireway - outer
Figure 66 -- Vertical
Figure
VerticalWireways
Wireways
8
adjustable
glide
WorkZone® Desks - 24”, 30” x 30” through 54” Tops with Power & Data
Assembly Instructions
WARNING: Assembly of all mechanical
frame components must be completed
before making any electrical connections.
All electrically connected furnishings must
also be mechanically connected.
mounting
bracket
adjustable
glide
#12 x 1"
screw
power/data
door
#10 x ½”
screw
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
adjustable
glide
#12 x
3
” screw
4
duplex
receptacle
#12 x 1" screw
modesty
panel
#10 x ½" screw
# 12 x 1"
screws
leg set
table-to-table
wireway
splice plate
worksurface
#1
door
clip
#12 x 1"
screw
10-wire
harness
Figure 1
vertical wireway-inner
(two cut-outs)
able requires
d up at the
s, the
aced by a
which is
through 17.
vertical wireway-outer
with power/data
(single cut-out)
transitional
leg
mbly right
lugs into the
e of each leg
wireway
wer & data
y - inner”
installed
e (Figures 2
-outer, with
) (Figures 2
e outside of a
ce the
never a
nstalled
he vertical Figure 2
to the leg set
leg plug
Tools Required
• Phillips Screwdriver
• Level
1. To avoid scratching the
worksurface, place the top face
down onto a soft protective
surface.
2. Attach two leg sets to worksurface
bottom by aligning legs to
pre-drilled holes and inserting
three #12 x 13/4” screws per leg
set (Figure 1).
Note: When a worksurface will
be paired with a transitional
unit, a leg set with a shorter
transitional foot (Figure 2)
will be assembled to the end
of the worksurface where the
transitional unit attaches. Refer to
your space-planning layout.
3. Align modesty panel between leg
sets. Insert two #10 x ½” screws
per left and right side of modesty
panel into leg. Do not tighten at
this time (Figure 1).
4. Position the mounting bracket
of the power/data door over
the modesty panel holes that
correspond with worksurface
holes. Insert three #12 x 1”
screws through the mounting
bracket and modesty panel into
splice
plate
table-to-table
wireway
the worksurface. Tighten all
screws to secure the leg sets and
modesty panel (Figure 1).
5. Fasten door clips to the underside
of the worksurface with two
#12 x 1” screws per door clip
(Figure 1).
Note: Whenever tables are to
be joined with a table-to-table
wireway and splice plate (Figures
1 & 2), the vertical wire way
(Figures 2 & 3) must be installed
into the leg prior to the
table-to-table wireway being
installed to the worksurface. Refer
now to step 9 and the note before,
if this is the case. Then return
back to step 6 below.
6. If worksurfaces will be ganged
together, attach
table-to-table wireway to
underside of worksurface with
two #12 x 1” screws on ganging
end(s). Also, attach splice plate
to worksurface with two #12 x 1”
screws at same end(s)
(Figures 1 & 2).
Note: All 10-wire harnesses
must be oriented the same
direction to make proper
connections. At one end of each
harness, on the black connector
near the clip, is an (N) and arrow
under the worksurface at the left
side, with the arrow pointing to
the modesty panel.
7. Correctly orient the 10-wire
harness to the underside of
the worksurface with the arrow
pointing to the modesty panel as
noted above (Figure 1). Position
10-wire harness to underside
of worksurface over pre-drilled
mounting holes and attach with
four #12 x 1” screws. Plug duplex
receptacle into power harness
as illustrated. Secure receptacle
to power harness by sliding
into port until spring clips lock
receptacle into place (Figure 1).
9
oles. Insert three #12 x 1” screws through
e mounting bracket and modesty panel
to the worksurface. Tighten all screws to
® panel
ecure the legWorkZone
sets and modesty
Desks igure 1). Assembly Instructions
Fasten door clips to the underside of the
orksurface with two #12 x 1” screws per
oor clip (Figure 1).
vertical wireway will be replaced by a
floor feed vertical wireway which is
explained in instructions 14 through 17.
24”, 30” x 30” through 54” Tops with Power & Data
10. If worksurface assemblies are to
be ganged, attach them together
with #12 x 1” screws at table-totable wireway and splice plate.
Do not tighten at this time.
10
transitional
leg
8. Stand worksurface assembly right
side up and install two leg plugs into the
exposed holes at the outside of each leg
set as illustrated (Figure 3).
Note: Two
different
vertical
wireway
Assemble units as described
herein
only. To
do otherwise
halves
are supplied
& data
ote: Whenever tables are to be
mayjoined
result with
in instability.
All screws,
nuts andwith
boltspower
must be
tables:
The
“vertical
wireway
inner”
table-to-table wireway and splice
plate
tightened securely and must be checked periodically after
(with two cut-outs) is to be installed
igure 1), the vertical wire way (Figures 2 &
assembly. Failure to assemble properly, or to secure parts
facing the inside of the table (Figures 2
must be installed into the leg prior to the
may result in assembly failure and personal injury.
& 3). The “vertical wireway-outer, with
ble-to-table wireway being installed
to the
power/data” (single cut-out) (Figures 2
orksurface. Refer now to step 9 and the
& 3) is to be installed on the outside of a
ote before, if this is the case. Then return
leg, and the cut-out must face the
ack to step 6 below.
Note: If the position of the table
11.
Level worksurface
by turning
underside
of the table.
Whenever a
requires
that
floor infeed
four adjustable
glides either
in
If worksurfaces
will
bethe
ganged
together,
”table-to-table
wireway”
is installed
be wired wireway
up at the to
endunderside
of a run of
or out.tables
The jambnuts
tach table-to-table
between
(Figure between
2), the vertical
worksurfaces,
the adjustable
glides
and the
orksurface of
with
two #12 xthe
1”vertical
screws on
wireways
must be
installed
to the leg set
wireway
will
be
replaced
by
a
bottom
of
the
leg
sets
anging end(s). Also, attach splice plate to
before the table-to-tablemust
wireway is
floor feed vertical wireway which
be tightened up against the
orksurface with two #12 x 1” screws at
installed.
is explained in instructions 14
bottom of the leg to secure
ame end(s) through
(Figure 17.
1).
the adjustable glides (Figure
wireways
fasten
into each
9. Vertical
3). Tighten
screws that
gang
other
from each atside
the leg set
be
ote: All 10-wire
8. Standharnesses
worksurfacemust
assembly
worksurfaces
thisoftime.
opening and must be oriented correctly
iented the same
direction
maketwo
proper
right side
up andtoinstall
leg
to press
together. Begin
by positioning
onnections.plugs
At one
end
each harness,
into
theofexposed
holes at on 12.
Press worksurface
grommets
an “outer
vertical
wireway”
(one cute black connector
nearof the
the outside
eachclip,
leg is
setan
as(N)
into wireway
holes
in
illustrated
(Figure 3). at the left
top (Figure
out),worksurface
to the outside
of the 3).
leg set as
nd arrow under
the worksurface
Route the
power
datafacing the
illustrated
with
the and
cut-out
de, with the arrow pointing to the modesty
Note: Two different vertical
module cordNext
through
the the inner
worksurface.
position
anel.
wireway halves are supplied
powercover
and data
module
hole in the
wireway
(two
cut-outs)
with power
& data tables:
Theto the
in theorientation
worksurface.
the of the
correct
at Snap
the inside
Correctly orient
the 10-wire
harness
“vertical wireway - inner” (with
power and data module into
nderside of the worksurface with the arrow
leg the
set module
and press
into the3).outer. Press
two cut-outs) is to be installed
holeit(Figure
ointing to the modesty panel as noted
a
vertical
wireway
cap
into the upper,
facing the inside of the table
From under the worksurface,
bove (Figure(Figures
1). Position
harness
outside
cut-out
in eachdoor
vertical wireway
2 & 3).10-wire
The “vertical
with the
power/data
underside wireway-outer,
of worksurface
over
pre-drilled
where
no
table-to-table
with power/data”
opened, plug the powerwireway
cord is
ounting holes
andcut-out)
attach with
four2#12
installed
(Figure
(single
(Figures
& 3) xis
into the
duplex3).
receptacle on
” screws. Plug
receptacle
into of a
to beduplex
installed
on the outside
the 10-wire harness. Check for
ower harness
illustrated.
leg,asand
the cut-outSecure
must face the
proper operation of the power
of the table.
Whenever
and data module. To open
ceptacle tounderside
power harness
by sliding
into
a ”table-to-table
wireway” isinto
module push down on the
ort until spring
clips lock receptacle
between tables (Figure
module and it will pop-up. To
ace (Figureinstalled
1).
2), the vertical wireways must
close, press downward and it
be installed to the leg set before
will snap closed.
the table-to-table wireway is
installed.
9. Vertical wireways fasten into each
other from each side of the leg
set opening and must be oriented
correctly to press together.
Begin by positioning an “outer
vertical wireway” (one cut-out),
to the outside of the leg set as
illustrated with the cut-out facing
the worksurface. Next position
the inner wireway cover (two cutouts) in the correct orientation at
the inside of the leg set and press
it into the outer. Press a vertical
wireway cap into the upper,
outside cut-out in each vertical
wireway where no table-to-table
wireway is installed (Figure 3).
with power/data
(single cut-out)
splice
plate
table-to-table
wireway
Figure 2
power & data
module
power and
data module
worksurface
grommet cover
leg plug
leg set
vertical
wireway-inner
vertical
wireway cap
Figure 3
Figure 3
vertical
wireway-outer
(end-of-run)
adjustable
glide
WorkZone® Desks - 24”, 30” x 30” through 54” Tops with Power & Data
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
WorkZone with Power & Data - Assembly Instructions
Note: All table connections
must be securely fastened
before any electrical
connections between
worksurfaces can be installed.
10-wire
harness
10-wire
harness
jumper cable
center vertical
wireways
Figure 4
Figure 4
13. To connect power between
worksurfaces, the power/
data door must be un-clipped
from the underside of ganged
10. If worksurface assemblies are to be
worksurfaces. The 10-wire
ganged, attach
them
#12
harnesses
cantogether
then be with
accessed
x 1” screws
at
table-to-table
wireway
to connect power between
and spliceworksurfaces.
plate. Do not
tighten
at this
Route
the jumper
time.
cable through access holes of
vertical wireways and
11. Leveltable-to-table
worksurfacewireway.
by turning
Plugfour
end either
of jumper
adjustableeach
glides
in orcable
out. The
the ends
the 10-wireglides
jambnutsinto
between
theofadjustable
harnesses
(Figure
4). must be
and the bottom
of the
leg sets
tightened up against the bottom of the
Note:theThe
power infeeds
leg to secure
adjustable
glides
are
to
be
connected
to thegang
(Figure 3). Tighten screws that
power source by a qualified
worksurfaces at this time.
electrician who must also check
the electrical integrity of the
12. Pressfinished
worksurface
system.grommets
These stepsinto
are
wireway holes
in worksurface
intended
as a guideline top
for the
(Figure 3).
Route the power and data
installation.
module cord through the power and
data module hole in the worksurface.
Snap the power and data module into
the module hole (Figure 3). From under
the worksurface, with the power/data
door opened, plug the power cord into
the duplex receptacle on the 10-wire
harness. Check for proper operation of
the power and data module. To open
module push down on the module and it
will pop-up. To close, press downward
and it will snap closed.
Note: All table connections must be
securely fastened before any electrical
connections between worksurfaces can
be installed.
13. To connect power between
worksurfaces, the power/data door
must be un-clipped from the underside
of ganged worksurfaces. The 10-wire
harnesses can then be accessed to
connect power between worksurfaces.
Route the jumper cable through access
holes of vertical wireways and table-totable wireway. Plug each end of jumper
cable into the ends of the 10-wire 11
harnesses (Figure 4).
WorkZone® Desks - 24”, 30” x 30” through 54” Tops with Power & Data
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
14. For 10-wire power infeed,
position the flexible conduit
between the vertical leg members
and plug the power infeed
connection into the 10-wire
harness under the table. Route
the uncased 10-wire through 90°
metal connector and through the
access hole of the infeed outer
wireway. Lay the oval conduit
flat (not on edge) into the bottom
half of the round 90° metal
connector. Assure the maximum
amount of conduit is inside the
fitting and connect the top half
of the fitting to the bottom. Use
screws supplied and assure that
the two sections are properly
connected, securely capturing
the flexible oval conduit
(Figure 5).
Note: The conduit and
connector assembly has been UL
Listed in KI’s UL file to meet the
requirements of UL 1286
“Office Furnishings”. The 90°
metal connector is limited to the
following models: EGS Appleton
AC96 or Cooper Crouse 738.
Substitutions are not allowed.
15. Route the uncased 10-wire
through the 90° pulling elbow.
Next screw or thread the 90°
metal connector into the 90°
pulling elbow, sandwiching the
steel infeed panel. Slide the
liquid-tight connector onto the
10-wires and connect it to the
90° pulling elbow (Figure 5)
16. Set the infeed outer wireway up
against the outside of the vertical
leg members with support lip
resting on the foot of the leg.
Position the infeed inner wire
way up against the inside of the
vertical leg members. Fasten
infeed inner wireway to infeed
outer wireway with six #10-32 x
1½”screws (Figure 5).
12
17. Determine the appropriate length
for the liquid-tight conduit (to
power source) and cut it to size.
Slide the liquid-tight conduit
onto the 10-wires and connect
the conduit to the connector on
the elbow. Finally the liquid-tight
conduit may be fastened to a
junction box (customer supplied)
and the 10-wires can be cut to
size and connected to the power
source (Figure 5).
10-wire
harness
power infeed
Important: The Listed conduit
of the power infeed is intended to
be terminated with a commonly
available Listed conduit fitting
appropriate for the type and trade
size of the conduit.
Note: The power infeeds
are to be connected to the
power source by a qualified
electrician who must also check
the electrical integrity of the
finished system. These steps are
intended as a guideline for the
installation.
18. The power/data door that is
attached to the modesty panel
snaps onto the two pre-installed
door clips at the underside of
the worksurface. The S-shaped
power/data divider that was
installed into the power/data
door is in place to separate
power from data lines (optional).
Note: This channel is not
to be used for routing
extension cords. Power
supply cords are not to be
routed across or through
more than one complete
unit/worksurface. Data lines
can be run through worksurface
grommets and exit through
knockout in infeed outer wireway
or notch on inside of center
vertical wireway. Snap the power/
data door to the door clips when
power and data lines have been
run.
infeed
outer
wireway
infeed
inner
wireway
uncased
10-wire
liquidtight conduit
(to power source)
oval
flexible
conduit
liquid-tight
connector
90o pulling elbow
support lip
Figure 5
round
o
90 metal
connector
WorkZone® Desks - 24”, 30” x 60”, 66” & 72” Tops with Power & Data
Assembly Instructions
WARNING: Assembly of all mechanical
frame components must be completed
before making any electrical connections.
All electrically connected furnishings must
also be mechanically connected.
power/data
door
adjustable
glide
#10 x ½"
screw
#12 x 1"
screw
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
#12 x
duplex
receptacle
3
” screw
4
mounting
bracket
#12 x 1" screw
modesty
panel
adjustable
glide
#10 x ½" screw
# 12 x 1"
screws
table-to-table
wireway
leg set
splice plate
worksurface
jumper cable
door
clip
Figure
1 1
Figure
able requires that
at the end of a
tical wireway
ed vertical
n instructions
vertical wireway-inner
(two cut-outs)
vertical wireway-outer
with power/data
(single cut-out)
transitional
leg
mbly right side up
the exposed
leg set as
Tools Required
• Phillips Screwdriver
• Level
1. To avoid scratching the
worksurface, place the top face
down onto a soft protective
surface.
2. Attach two leg sets to worksurface
bottom by aligning legs to
pre-drilled holes and inserting
three #12 x 13/4” screws per leg
set (Figure 1).
Note: In the instance where a
worksurface is to be paired with
a transitional unit, a leg set with
a short transitional foot (Figure
2) will be assembled to the end
of the worksurface where the
transitional unit is to be attached.
Refer to your space-planning
layout.
3. Align modesty panel between leg
sets. Insert two #10 x ½” screws
per left and right side of modesty
panel into leg. Do not tighten at
this time (Figure 1).
wireway halves
ata tables: The
with two cutg the inside of
e “vertical
ata” (single cutinstalled on the
-out must face
Whenever a
nstalled (Figure
st be installed to
o-table wireway
splice
plate
table-to-table
wireway
Figure 2
nto each other
10-wire
#12 x 1" harnesses
screw
leg plug
4. Position the mounting bracket
of the power/data door over
the modesty panel holes that
correspond with worksurface
holes. Insert three #12 x 1”
screws through the mounting
bracket and modesty panel into
the worksurface. Tighten all
screws to secure the leg sets and
modesty panel (Figure 1).
5. Fasten door clips to the underside
of the worksurface with two
#12 x 1” screws per door clip
(Figure 1).
Note: Whenever tables are to
be joined with a table-to-table
wireway and splice plate (Figures
1 & 2 ), the inner and outer
vertical wireway sections must
be installed into the leg prior
to installing the table-to-table
wireway to the worksurface. Refer
now to the “Note” and step 9 if
this is the case. Then return back
to step 6 below.
6. If worksurfaces will be ganged
together, attach table-totable wireway to underside of
worksurface with two #12 x 1”
screws on ganging end(s). Also,
attach splice plate to worksurface
with two #12 x 1” screws at same
end(s) (Figures 1 & 2).
Note: All 10-wire harnesses
must be oriented the same
direction to make proper
connections. At one end of each
harness, on the black connector
near the clip, is an (N) and arrow
under the worksurface at the left
side, with the arrow pointing to
the modesty panel.
7. Correctly orient the two 10-wire
harnesses to the underside of
the worksurface with the arrows
pointing to the modesty panel
as noted above (Figure 1).
Position the 10-wire harnesses
to underside of worksurface over
pre-drilled mounting holes and
attach with four #12 x 1” screws.
Plug duplex receptacle into power
harness as illustrated. Secure
receptacle to power harness by
sliding into port until spring
clips lock receptacle into place
(Figure 1). Note: If the position
of the table requires that the floor
infeed be wired up at the end of a
run of worksurfaces, the vertical
wireway will be replaced by a
floor feed vertical wireway which
is explained in instructions 14
through 17.
13
Figure 2
Position the mounting bracket of the
ower/data door over the modesty panel
®
oles that correspond
with worksurface
WorkZone
Desks oles. Insert three
#12
x
1”
screws
through
Assembly Instructions
e mounting bracket and modesty panel
to the worksurface. Tighten all screws to
cure the leg sets and modesty panel
igure 1).
Note: If the position of the table requires that
the floor infeed be wired up at the end of a
run of
worksurfaces,
the vertical
24”,
30”
x 60”, 66”
& 72”wireway
Tops with
will be replaced by a floor feed vertical
wireway which is explained in instructions
14 through 17.
vertical wireway-inner
(two cut-outs)
Power & Data
vertical wireway-outer
with power/data
(single cut-out)
transitional
leg
8. Stand worksurface assembly right side up
and
install
two
leg
plugs
into
the
exposed
Assemble units as described herein only. To do otherwise
Fasten door clips to the underside
of the
holes
the outside
eachmust
leg be
set as
may result
in instability.
All at
screws,
nuts andofbolts
orksurface with two #12 x 1” screws per
illustrated (Figure 3).
tightened securely and must be checked periodically after
oor clip (Figure 1).
assembly. Failure to assemble properly, or to secure parts
Note: Two different vertical wireway halves
mayjoined
result with
in assemblyare
failure
and personal
injury.& data tables: The
supplied
with power
ote: Whenever tables are to be
“vertical wireway - inner” (with two cuttable-to-table wireway and splice plate
outs) is to be installed facing the inside of
igures 1 & 2 ), the inner and outer vertical
the table (Figures 2 & 3). The “vertical
reway sections must be installed into the
splice
Stand worksurface
assembly
the leg setswith
mustpower/data”
be tightened (single cutwireway-outer,
g prior to8.installing
the table-to-table
plate
right
side up and Refer
install now
two leg
up against2 the
bottom
leg on the
out) (Figures
& 3)
is to of
bethe
installed
reway to the
worksurface.
to
plugs
exposed
to secure
theand
adjustable
glidesmust face
outside
of a leg,
the cut-out
e “Note” and
stepinto
9 ifthe
this
is the holes
case. at
the outside
leg set as
(Figure 3).ofTighten
screws
that
the underside
the table.
Whenever
a
hen return back
to stepof6each
below.
illustrated (Figure 3).
gang worksurfaces
at this
time. (Figure
”table-to-table
wireway”
is installed
If worksurfaces will be ganged together,
2), the vertical wireways must be installed to
Note: Two
different
12.leg
Press
grommets into wireway
tach table-to-table
wireway
to vertical
underside of
the
setworksurface
before the table-to-table
table-to-table
wireway
wireway holes in worksurface top
orksurface wireway
with twohalves
#12 are
x 1”supplied
screwswith
on
is installed.
power
& data
tables:
Theplate
“vertical
(Figure 3). Route the power and
anging end(s).
Also,
attach
splice
to
Figure 2
inner”x(with
two at
data module
cordfasten
throughinto
theeach other
orksurface wireway
with two- #12
1” screws
9. Vertical
wireways
is to be installed facing
and data
module
hole
in
me end(s) cut-outs)
(Figure 1).
from power
each side
of the
leg set
opening
and
power & data
the inside of the table (Figures 2
Snap the
mustthe
be worksurface.
oriented correctly
to power
press together.
module
& 3).harnesses
The “verticalmust
wireway-outer,
into the
be
Beginand
by data
firstmodule
positioning
an module
“outer vertical
ote: All 10-wire
with power/data”
hole (Figure
From under
theoutside of
wireway”
(single3).
cut-out),
to the
iented the same
direction to(single
makecut-out)
proper
2 & of
3) each
is to be
installedon
worksurface,
with the power/data
power and
the leg
set as illustrated,
with cut-out closest
onnections. (Figures
At one end
harness,
data module
on the outside
of aclip,
leg,isand
door opened,Next
plugposition
the powerthecord
to worksurface.
inner
e black connector
near the
anthe
(N)
cut-out
face the underside
into cover
the duplex
wireway
(tworeceptacle
cut-outs)oninthe
the correct
d arrow under
themust
worksurface
at the left
worksurface
the table.
Whenever
10-wireatharness.
Check
for leg
proper
grommet cover
orientation
the inside
of the
set and
de, with theofarrow
pointing
to thea modesty
”table-to-table wireway” is
the power
and data
pressoperation
it into theof outer
wireway
(Figures 2 &
anel.
installed (Figure 2), the vertical
module.
opentables,
module
pusha vertical
3). For
end-ofTorun
press
wireways
be installed to the
downcap
on into
the module
and outside
it will cut-out
Correctly orient
the must
two 10-wire
wireway
the upper,
leg plug
before theoftable-to-table
pop-up.
To close,
press
downward
rnesses to leg
theset
underside
the
in each
vertical
wireway
where
no table-toinstalled.
it will is
snap
closed.(Figure 3).
orksurface wireway
with theisarrows
pointing to the
table and
wireway
installed
odesty panel as noted above (Figure 1).
9. 10-wire
Vertical wireways
fasten
into each
osition the
harnesses
to underside
leg set
vertical
other
from
each sidemounting
of the leg
worksurface
over
pre-drilled
wireway-inner
set opening
and#12
mustx be
oles and attach
with four
1” oriented
screws.
correctly tointo
presspower
together.
ug duplex receptacle
harness
by receptacle
first positioning
an
illustrated.Begin
Secure
to power
“outer into
vertical
(single
rness by sliding
portwireway”
until spring
clips
vertical
cut-out),
to the(Figure
outside1)of. the leg
wireway cap
ck receptacle
into place
set as illustrated, with cut-out
closest to worksurface. Next
position the inner wireway cover
(two cut-outs) in the correct
orientation at the inside of the
vertical
leg set and press it into the outer
adjustable
wireway-outer
wireway (Figures 2 & 3). For
glide
(end-of-run)
end-of run tables, press a vertical
Figure 3
wireway cap into the upper,
Figure 3
outside cut-out in each vertical
wireway where no table-to-table
wireway is installed (Figure 3).
10. If worksurface assemblies are to
be ganged, attach them together
with #12 x 1” screws at table-totable wireway and splice plate.
Do not tighten at this time.
11. Level worksurface by turning
four adjustable glides either in
or out. The jambnuts between
the glides and the bottom of
14
WorkZone® Desks - 24”, 30” x 60”, 66” & 72” Tops with Power & Data
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Note: All table connections must
be securely fastened before any
electrical connections between
worksurfaces can be installed.
10-wire
harness
13. To connect power between
worksurfaces, the power/
data door must be unclipped
from the underside of ganged
worksurfaces. The 10-wire
harness can then be accessed
to connect power between
worksurfaces. Route the jumper
cable through access holes of
vertical wireways and table-totable wireway. Plug each end of
jumper cable into the ends of the
10-wire harnesses (Figure 4).
10-wire
harness
jumper cable
center vertical
wireways
Figure 4
15
WorkZone® Desks - 24”, 30” x 60”, 66” & 72” Tops with Power & Data
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
14. For 10-wire power infeed,
position the flexible conduit
between the vertical leg
members and plug the power
infeed connection into the
10-wire harness under the table.
Route the uncased 10-wire
through 90° metal connector
and through the access hole of
the infeed outer wireway. Lay the
oval conduit flat (not on edge)
into the bottom half of the round
90° metal connector. Assure the
maximum amount of conduit is
inside the fitting and connect
the top half of the fitting to the
bottom. Use screws supplied
and assure that the two sections
are properly connected, securely
capturing the flexible oval
conduit (Figure 5).
Note: The conduit and
connector assembly has been
UL Listed in KI’s UL file to meet
the requirements of UL 1286
“Office Furnishings”. The 90°
metal connector is limited to the
following models: EGS Appleton
AC96 or Cooper Crouse 738.
Substitutions are not allowed.
15. Route the uncased 10-wire
through the 90° pulling elbow.
Next screw or thread the 90°
metal connector into the 90°
pulling elbow, sandwiching the
steel infeed panel. Slide the
liquid-tight connector onto the
10-wires and connect it to the
90° pulling elbow (Figure 5)
16. Set the infeed outer wireway
up against the outside of the
vertical leg members with
support lip resting on the foot of
the leg. Position the infeed inner
wire way up against the inside
of the vertical leg members.
Fasten infeed inner wireway to
infeed outer wireway with six
#10-32 x 1½” screws
(Figure 5).
16
17. Determine the appropriate
length for the liquid-tight
conduit (to power source) and
cut it to size. Slide the
liquid-tight conduit onto the
10-wires and connect the
conduit to the connector on
the elbow. Finally the liquidtight conduit may be fastened
to a junction box (customer
supplied) and the 10-wires can
be cut to size and connected to
the power source (Figure 5).
10-wire
harness
power infeed
Important: The Listed
conduit of the power infeed is
intended to be terminated with
a commonly available Listed
conduit fitting appropriate for
the type and trade size of the
conduit.
Note: The power infeeds
are to be connected to the
power source by a qualified
electrician who must also
check the electrical integrity
of the finished system. These
steps are intended as a
guideline for the installation.
18. The power/data door that
is attached to the modesty
panel snaps onto the two
pre-installed door clips at the
underside of the worksurface.
The S-shaped power/data
divider that was installed into
the power/data door is in
place to separate power from
data lines (optional). Note:
This channel is not to be
used for routing extension
cords. Power supply
cords are not to be routed
across or through more
than one complete unit/
worksurface. Data lines can
be run through worksurface
grommets and exit through
knockout in infeed outer
wireway or notch on inside of
center vertical wireway. Snap
the power/data door to the
door clips when power and
data lines have been run.
infeed
outer
wireway
infeed
inner
wireway
uncased
10-wire
liquidtight conduit
(to power source)
oval
flexible
conduit
liquid-tight
connector
o
90 pulling elbow
support lip
Figure 5
Figure 5
round
90o metal
connector
WorkZone® Desks - New York City Power In-Feed
Assembly Instructions
WARNING: Assembly of all mechanical
frame components must be completed
before making any electrical connections.
All electrically connected furnishings must
also be mechanically connected.
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
New York City Guidelines
A. All components must be installed
by an electrician licensed in New
York City.
B. All branch circuit wiring must be
#12 AWG minimum.
Data - Assembly Instructions
by
City.
C. Each branch circuit must be fused
at 15 AMP maximum with no
more than 10 outlets per circuit.
5. Make standard wire connections to the
wires inside the power-in box with wire
nuts. Secure the cover back onto the
power-in box to complete the hook up.
D. A service entry box must be
provided with a service panel.
The box must be approximately
2.25 cubic inches for each wire
entering the box plus 2.25 cubic
inches for each wire leaving the
box.
#12
d at
n 10
Note: The power infeeds are to be
connected to the power source by a
qualified electrician who must also check
the electrical integrity of the finished
system. These steps are intended as a
guideline for the installation.
E. Flexible metal conduit from the
supply source to the panel may
not exceed 18 inches in length
and must be hardwired at both
ends, per Article 4 of the New
York Electrical Code.
ded
be
each
c
adjustable
1
#10-32 x 1 /2"
glide
infeed
screw
inner wireway
pply
18
red
w
al
City
wing
14
ar
mbly
adjustable
glide
jamb-nut
mounting
bracket
duplex
receptacle
#10 x 1/2"
screw
infeed
outer wireway
#12 x 1"
screw
modesty
panel
gth
power infeed
(customer provided)
(see
worksurface
r-in
t to
ame
York
he
ter
#12 x 1"
screw
NY City
power-in box
3
#12 x 1 /4"
screw
Figure 1
Figure 1
wireway
(optional)
door
clip
#12 x 1"
screw
New York
10-wire harness
Note: The following is a
supplemental assembly
instructions for New York
City Installations. Please refer
to the following steps and
Figure 1 in place of steps 14
through 17 of the rectangular
WorkZone with Power & Data
Assembly Instructions.
1. Begin by mounting the special
length New York 10-wire
harness to the underside of
the table in the same fashion
as prior harnesses mounted
(see step 7, page 9 in standard
rectangular worksurface
instructions) (Figure 1).
2. Next, connect the New York
power-in box to the wire
harness and mount it to the
underside of the table with the
same #12 x 1” screws as the
harness (Figure 1).
3. Remove the cover from the
New York power-in box and a
knock out from the side of the
box where power is to enter
(Figure 1).
4. Route from a power source,
the New York Code customer
supplied flexible conduit,
ten wires through the infeed
outer wireway and through
leg assembly to the power-in
box utilizing all necessary
connectors (not furnished)
(Figure 1).
5. Make standard wire
connections to the wires
inside the power-in box with
wire nuts. Secure the cover
back onto the power-in box to
complete the hook up.
Note: The power infeeds
are to be connected to the
power source by a qualified
electrician who must also
check the electrical integrity
of the finished system. These
steps are intended as a
guideline for the installation.
17
WorkZone® Stand Alone Corner Worksurface with Keyboard Pad
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
#12 x
#12 x 1" screw
#10 x ½" screw
leg plug
adjustable
glide
corner leg
#12 x 1" screw
modesty panel
#12 x ½”Carriage bolt, washer and adjustment knob
#10 x ½" screw
#12 x 1"
screw
#10 x ½"
screw
modesty panel
adjustable
glide
leg set
Tools Required
• Phillips Screwdriver
• Level
1. To avoid scratching the
worksurface, place the top face
down onto a soft protective
surface.
corner
worksurface
2. Attach two leg sets to worksurface
bottom by aligning legs to
pre-drilled holes and inserting
three #12 x 13/4” screws per leg
set (Figure 1).
3. Position the corner leg over the
pre-drilled holes in the back
corner of the worksurface. Be
sure the modesty panel mounting
holes are oriented as shown.
Attach the corner leg to the
worksurface with four #12 x 1”
screws. Do not tighten at this
time (Figure 1).
18
horizontal
wireway
(optional)
Figure 1
WorkZone® Stand Alone Corner Worksurface with Keyboard Pad
Assembly Instructions
Keyboard Pad
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
mbly right side up
into the two
tside of each leg
3).
e by turning the
ther in or out. The
lides and the
must be tightened
f the leg to
3).
ommet into
ner of
small
bracket
washer
large
bracket
#12 x 1”
screw
#12 x 1"
screw
adjustment
knob
corner
worksurface
keyboard pad
4. Align the first modesty panel
between a leg set and corner leg.
If optional horizontal wireways
are to be installed to unit, place
the wireways between mounting
flange of modesty panel and
the worksurface, aligning the
mounting holes as illustrated.
Insert two #10 x ½” screws per
left and right side of the modesty
panel into the leg set and corner
leg. Attach modesty panel to
worksurface with two #12 x 1”
screws. Do not tighten at this
time. Repeat this step for second
modesty panel. Tighten all screws
attaching the leg sets, corner leg
and modesty panel (Figure 1).
Note: If assembling stand
alone corner keyboard unit see
instructions A through D and then
continue on to steps 5 though 9.
If assembling stand alone unit
without keyboard, skip now to
steps 5 through 9.
Keyboard Pad Only
A. Attach two small brackets to the
keyboard pad by first aligning
holes in the keyboard pad. Insert
six #12 x 1” screws, three per
small bracket, but do not tighten
completely (Figure 2).
B. Attach the two large brackets
to the pre-drilled holes in
worksurface with four #12 x 1”
screws per bracket, but do not
tighten completely (Figure 2).
C. Assemble and tighten four
adjustment knobs, connecting the
small brackets on the keyboard
pad to the large brackets on the
corner worksurface. These knobs
consist of carriage bolt, washer
and tightening knob for each set
(Figure 2).
Figure 22
Figure
leg plug
vertical
wireway - inner
leg set
D. Center the keyboard pad to the
opening in the worksurface.
Tighten all bracket screws
completely, starting with the large
brackets on the worksurface.
(Figure 2).
5. Carefully stand assembly right
side up and install two leg plugs
into the two exposed holes at
the outside of each leg set as
illustrated (Figure 3).
vertical
wireway - outer
Figure 3
Figure 3
adjustable
glide
6. Level the worksurface by turning
the four adjustable glides either
in or out. The jambnuts between
the glides and the bottom of the
leg sets must be tightened up
against the bottom of the leg to
secure the glide (Figure 3).
7. Press worksurface grommet into
wireway hole at rear corner of
worksurface.
19
WorkZone® Transitional Worksurface - Keyboard Pad & Corner
Assembly Instructions
Assembly Instructions
WorkZone Transitional Worksurface
Keyboard Pad & Corner
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
#12 x 1" screw
splice
plates
1
#10 x /2" screw
#12 x
return
worksurface
primary
worksurface
#12 x 1"
screw
#12 x ½” Carriage bolt, washer and adjustment knob
Tools Required
• Phillips Screwdriver
• Level
Note: The corner transitional
worksurface is not illustrated
but is assembled in the same
manner as the keyboard pad
corner transitional.
Note
work
asse
keyb
1. At
work
splic
plate
Figure 1
Figure 1
1. Attach two-splice plates to the
primary worksurface with two
#12 x 1” screws per splice
plate. Repeat the procedure
for splice plates to the return
surface (Figure 1).
adjustable
glide
#12 x 1" screw
modesty panel
1
#10 x /2" screw
#12 x 1"
screw
modesty panel
corner
transitional
worksurface
horizontal wireway
(optional)
Figure 2
Figure 2
20
2. To
work
soft
corner leg
2. To avoid scratching the
transitional worksurface, place
the top face down onto a soft
protective surface (Figure 2).
3. Position the corner leg over the
pre-drilled holes in the back
corner of the worksurface.
Be sure the modesty panel
mounting holes are oriented as
shown. Attach the corner leg to
the worksurface with four
#12 x 1” screws. Do not
tighten at this time (Figure 2).
Tools
Ph
Le
3. Po
holes
Orien
of th
mod
corn
#12
(Figu
WorkZone® Transitional Worksurface - Keyboard Pad, Square & Rectangle & Corner
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
return
d so they are in
ransitional unit
tional assembly
set it onto the
y and return
ounting holes of
rilled holes in
nsert two
each splice
worksurface
small
bracket
washer
large
bracket
#12 x 1”
screw
#12 x 1"
screw
adjustment
knob
n be identified
foot, for less
anels to the
of the primary
with two
igure 4).
crews in the
evel the
he adjustable
jambnuts
des and the
st be tightened
he leg to
es (Figure 2).
stallation, use a
tead of a splice
nstalled in the
ates.
corner
worksurface
keyboard pad
Figure 3
Figure 3
Note: If assembling transitional
corner keyboard unit see
instructions A through D and then
continue on to steps 5 though
9. If assembling transitional unit
without keyboard, skip now to
steps 5 through 9.
attach to
transitional
leg
Keyboard Pad Only
A. Attach two small brackets to the
keyboard pad by first aligning
holes in the keyboard pad. Insert
six #12 x 1” screws, three per
small bracket, but do not tighten
completely (Figure 3).
#10 x 1/2"
screw
primary
worksurface
return
worksurface
#12 x 1"
screw
transitional
leg set
Figure
Figure4 4
4. Align one modesty panel to the
corner leg and worksurface
mounting holes. If optional
horizontal wireways are to be
installed to unit, place wireways
between the mounting flange
of the of the modesty panel and
the worksurface, aligning the
mounting holes as illustrated.
Insert two #10 x ½” screws
through the modesty panel
and into the corner leg. Attach
modesty panel (through optional
horizontal wireways if applicable)
to worksurface with two
#12 x 1” screws. Do not tighten
at this time. Repeat this step for
second modesty panel. Tighten
all screws attaching the corner
leg and the modesty panels
(Figure 2).
adjustable
glide
B. Attach the two large brackets
to the pre-drilled holes in
worksurface with four #12 x 1”
screws per bracket, but do not
tighten completely (Figure 3).
C. Assemble and tighten four
adjustment knobs, connecting the
small brackets on the keyboard
pad to the large brackets on the
corner worksurface. These knobs
consist of carriage bolt. washer
and tightening knob for each set
(Figure 3).
D. Center the keyboard pad to the
opening in the worksurface.
Tighten all bracket screws
completely, starting with the large
brackets on the worksurface.
(Figure 3).
5. Orient the primary and return
worksurfaces as illustrated so
they are in position to assemble
the transitional unit in step 7
(Figure 4).
6. Carefully turn the transitional
assembly right side up and set
it onto the splice plates of the
primary and return worksurface.
Align the mounting holes of the
splice plats with pre-drilled holes
in transitional worksurface. Insert
two #12 x 1” screws through each
splice plate into the transitional
worksurface and tighten
(Figure 4).
Note: Transitional legs can
be identified by their shorter,
floor-level foot, for less restricted
movement.
7. Attach both modesty panels to the
adjoining transitional legs of the
primary and return worksurfaces
with two #10 x ½” screws each
(Figure 4).
8. Tighten all remaining screws in
the worksurface assembly. Level
the worksurfaces by turning the
adjustable glides either in or
out. The jambnuts between the
adjustable glides and the bottom
of the leg sets must be tightened
up against the bottom of the leg
to secure the adjustable glides
(Figure 4).
Note: In a “step down”
installation, use a Z-bracket (not
shown) instead of a splice plate.
The Z-brackets are installed in the
same manner as splice plates.
21
WorkZone® - Corner Transitional & End-of-Run Corner Worksurface with Power & Data
Assembly Instructions
WARNING: Assembly of all mechanical
frame components must be completed
before making any electrical connections.
All electrically connected furnishings must
also be mechanically connected.
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Tools Required
• Phillips Screwdriver
• Level
Note: The following
instructions illustrate a typical
corner assembly attached
to a series of rectangular
worksurfaces; the run of
worksurfaces ends with the
corner worksurface. Your
configuration may vary.
1. Carefully place the corner
worksurface face down on a
soft protective surface
(Figure 1). The corner
worksurface should be
assembled near the adjoining
rectangular worksurface(s),
because they will be connected
in a later step.
2. Begin assembly by attaching
the 10-wire harness to the
underside of the corner
worksurface at pre-drilled
mounting holes with four
#12 x 1” screws. Plug
duplex receptacle into power
harness as illustrated. Secure
receptacle to power harness by
sliding into port until spring
clips lock receptacle into place
(Figure 1).
3. Verify with the space-planning
layout which side(s) of the
corner worksurface will
connect to an adjoining
rectangular worksurface
(corner transitional), and/or be
the “end-of-run” (Figure 1).
#12 x
3
” screw
4
#12 x 1" screw
#10 x ½" screw
leg plug
adjustable
glide
power/data door
(transitional)
modesty panel
(transitional)
#10 x ½”
screw
mounting
bracket
power/data
corner bracket
power/data door
(end-of-run)
#12 x 1"
screw
#12 x 1"
screws
#10 x ½"
screw
modesty panel
(end-of-run)
#12 x 1"
screw
duplex
receptacle
leg set
(end-of-run)
to adjoining
rectangular
worksurface
power-pass-through
connector
Figure 1
Figure 1
22
corner leg
corner
worksurface
#12 x 1"
screw
door clip
10-wire
harness
#1
rectangular
two #12 x 1” screws through the
worksurface. Be sure the modesty panel
worksurface
mounting bracket, the modesty panel
mounting holes of the corner leg are
oriented as shown. Secure the corner leg ® and into the worksurface. Tighten all
WorkZone
- screws
Corner
Transitional
and
End-of-Run Corner Worksurface with Power & Data
that secure
the modesty
panels
to the worksurface with four
#12 x 1”
Assembly Instructions
to the corner leg, the leg sets and the
screws (Figure 1).
power/data
door
worksurface (Figure 1).
1
#10 x /2"
Note: Corner transitional modesty panels
screw
10. Route the power-pass-through
leg plug
are the longer of the two types of
connector through the power and data
splice
modesty panels. They bridge between the
plates herein only. To do otherwise
Assemble units as described
corner bracket and snap the connector
corner worksurface and the adjoining
leg set may result in instability. All screws, nuts and bolts must be
into the 10-wire harness. Route the
rectangular worksurface to connect the
(end-of-run)
transitional
trailing end inside the power/data door.
tightened securely and must be checked periodically leg
after
two together. End-of-run modesty panels
#12
x 1" or to secure parts
corner are shorter and fit between the corner leg
Snap both power/data doors shut at the
assembly. Failure to assemble
properly,
adjustable
screws
ger or shorter
door clips (Figure 1).
and the “end-of-run” leg set.
may result in assembly failure and personal injury.glide
ransitional or
Figure 2
ls. The 6. Align the transitional
Note: If the corner worksurface being
powermodesty
& data panel
ata doorwith
is the corner leg and
module
assembled includes a keyboard pad,
the corner
worksurface
follow
instructions A through D below.
worksurface mounting holes. Position the
grommet
Otherwise skip to step 11.
“end-of-run” modesty panel over the
acket ofworksurface
the
modesty panel
small
mounting holes, between
large
(transitional)
bracket
r over the
Keyboard
Pad
Assembly
the corner
leg
and
the
“end-of-run”
leg
bracket #12 x 1"
power & data
corner
1
orrespond
A. Attach the two small brackets to the
#10 x /2"
screw
set. Note
that the lower right screwworksurface
hole
module
adjoining
screw
urface. Insert
keyboard pad by aligning the
holes in the
in the corner leg is to be used to secure
washer
rectangular
gh the the power/data corner bracket and should
small brackets with the pre-drilled
holes
worksurface
esty panel
in the keyboard pad. Insert three #12 x
not be used until step 8. Fasten the
ighten all
1” screws per bracket, but do not tighten
modesty panels to the corner leg. For
adjustment
desty panels
completely (Figure 3).
“end-of-run” assemblies, attach modesty
knob
ts and the
panel to leg set with #10 x ½” screws. power/data
door
B. Align the two large brackets to the
Do not tighten screws at this time.
pre-drilled
#10 x 1/2" holes in the corner
screw
hrough 7. Positionleg
worksurface.
Insert four #12 x 1”
theplug
power/data corner bracket
corner
worksurface
er and data
splice per large bracket, but do not
screws
into the back corner of the worksurface
plates (Figure 3).
e connector
tighten
against the corner leg. Insert the #10 x
leg set
oute the½” screw (left out in(end-of-run)
step 6) through the
transitional
r/data door.
C. Assemble four adjustment knobs
keyboard pad
leg to
corner bracket, the modesty panel and
#12 xbrackets
1"
s shut atinto
thethe corner leg. Do not tighten at this
connect small
to
large
adjustable
screws
Figure 3
glidethrough
brackets. Insert carriage bolts
time. Figure
Align the2four mounting holes of the
Figure 3
small
bracket,
a
washer,
the
large
corner bracket
with
the
holes
in
the
Figure 2
legbracket
and the corner
worksurface
a keyboard pad, follow
Note: If you
not assembling
face being
and secure
with an adjustmentNote: Power/data doors for
worksurface
andaresecure
with #12 x 1”
mounting
holes.
Position
the
corner
worksurfaces
are
sized
instructions A through D below.
an
end-of-run
corner
oard pad,
knob
(Figure
3).
screws (Figure 1).
“end-of-run” modesty panel over
longer or shorter to correspond
Otherwise skip to step 11.
h D below.worksurface, go on to step 5.
theD.
worksurface
holes,
Center themounting
keyboard
pad inside the with corner transitional or “end8. Fasten door clips to the underside of
between
the in
corner
leg andworksurface.
the
of-run” modesty panels. The
Keyboard Pad Assembly
4. On
the “end-of-run”
side #12
of thex 1”
small
opening
thelarge
corner
the
worksurface
with two
bracketwith
“end-of-run”
legbracket
set.
that
corner transitional power/data
A. Attach the two small brackets
corner
align a 1).
leg
Starting
the Note
large#12
brackets
on
the
screws
perworksurface,
door clip (Figure
x 1"
1
thexworksurface,
lower
hole all
inscrew
the
to the keyboard pad by aligning
ckets to theset to the pre-drilled holes and
tighten
bracket screwsdoor is the longer of the two.
#10
/2" right screw
screw
corner
leg
is
to
be
used
to
secure
the holes in the small brackets
secure the leg set with three
e holes in the
completely
(Figure
3).
washer
the power/data corner bracket and
9. Position the mounting bracket
with the pre-drilled holes in the
#12 x 1 3 /4” screws (Figure 1).
-drilled holes
should not be used until step 7.
of the appropriate power/data
keyboard pad. Insert three
three #12 x
Fasten the modesty panels to
door over the modesty panel
#12 x 1” screws per bracket, but
5. Position the corner leg over the
do not tighten
the
corner
leg.
For
“end-of-run”
holes
that
correspond
with
the
do not tighten completely
four pre-drilledadjustment
holes
at
the
back
knob
assemblies, attach modesty panel
holes in the worksurface. Insert
(Figure 3).
corner of the worksurface. Be
to leg set with #10 x ½” screws.
two #12 x 1” screws through the
ets to the sure the modesty panel mounting
Do not tighten screws at this
mounting bracket, the modesty
B. Align the two large brackets to
holes of the corner leg are
er
time.
panel and into the worksurface.
the pre-drilled holes in the corner
oriented as shown.
Secure the
12 x 1”
corner
worksurface
Tighten all screws that secure
worksurface. Insert four #12 x 1”
worksurface with
ut do not corner leg to the
7. Position the power/data corner
the modesty panels to the
screws per large bracket, but do
four #12 x 1” screws (Figure 1).
bracket into the back corner
corner leg, the leg sets and the
not tighten (Figure 3).
of the worksurface against the
worksurface (Figure 1).
nt knobs toNote: Corner transitional
corner leg. Insert the #10 x ½”
C. Assemble four adjustment knobs
modesty panels are the longer
arge
screw (left out in step 6) through
10. Route the power-pass-through
to connect small brackets to large
types
of
modesty
lts throughof the two
Figure 3
the corner bracket, the modesty
connector through the power
brackets. Insert carriage bolts
panels. They bridge between
e large
panel and into the corner leg.
and data corner bracket and
through small bracket, a washer,
adjustmentthe corner worksurface and the
Do not tighten at this time. Align
snap the connector into the
the large bracket and secure with
adjoining rectangular worksurface
the four mounting holes of the
10-wire harness. Route the
an adjustment knob (Figure 3).
to connect the two together.
corner bracket with the holes in
trailing end inside the power/
inside the End-of-run modesty panels are
the worksurface and secure with
data door. Snap both power/
D. Center the keyboard pad
surface. shorter and fit between the corner
#12 x 1” screws (Figure 1).
data doors shut at the door clips
inside the opening in the
kets on the leg and the “end-of-run” leg set.
(Figure 1).
corner worksurface. Starting
cket screws
8. Fasten door clips to the
with the large brackets on the
6. Align the longer transitional
underside of the worksurface
Note: If the corner worksurface
worksurface, tighten all bracket
modesty panel with the corner
with two #12 x 1” screws per
being assembled includes
screws completely (Figure 3).
door clip (Figure 1).
23
WorkZone® - Corner Transitional and End-of-Run Corner Worksurface with Power & Data
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
11. Secure two splice plates to
the pre-drilled holes at the
underside of the adjoining
rectangular worksurfaces.
Use two #12 x 1” screws each
(Figure 2).
12. Carefully turn the corner
worksurface right side up and
set the appropriate edge onto
the splice plates of the adjoining
rectangular worksurface. Use
four #12 x 1” screws to attach
the splice plates to the corner
worksurface. Do not tighten the
screws at this time (Figure 2).
13. Unclip and open the transitional
side power/data door under
the corner worksurface and
the power/data door under
the adjoining rectangular
work surface. Secure the
modesty panel to the leg set
of the adjoining rectangular
worksurface with two
#10 x ½” screws. Route the
trailing end of the power-passthrough connector through the
notched vertical wireway in the
leg of the adjoining rectangular
worksurface and snap the
connector end into the 10-wire
harness (Figure 2).
Note: All table connection must
be securely fastened before any
electrical connections between
worksurfaces are installed.
14. Route the power and data
module cord through the power
and data module hole in the
worksurface. Snap the module
into the module hole (Figure 4).
15. From under the worksurface,
with the power/data door
opened, plug the power cord
into the duplex receptacle on the
10-wire harness. Check for proper
operation of the power and data
module. To open, push down on
the module and it will pop up. To
close, press downward and it will
snap closed.
16. Level the worksurfaces by turning
the adjustable glides either in or
out. The jambnuts between the
adjustable glides and the bottom
of the leg sets must be tightened
up against the bottom of the leg
to secure the adjustable glides.
Tighten all screws that gang the
worksurfaces together at this time
(Figure 4).
17. Vertical wireways fasten into each
other from each side of the leg
set opening and must be oriented
correctly to snap together. Begin
by first positioning an “outer
vertical wireway” (single-cut-out),
to the outside of the leg set as
illustrated, with cut-out closest
to worksurface. Next position
the inner wireway cover (two
cut-outs) in the correct orientation
at the inside of the leg set and
snap it into the outer wireway
(Figure 4). For end-of run tables,
snap a vertical wireway cap into
the upper, outside cut-out in the
vertical wireway, and install leg
plugs into holes in the vertical
leg members to finish table off
(Figure 4)
18. Install a worksurface grommet
into the wireway hole at the back
corner of the worksurface
(Figure 2).
19. The power/data door that is
attached to each modesty panel
snaps into the door clips at the
underside of the worksurface.
The S-shaped power/data
divider that was installed into
the power/data door is in place
to separate power from data
lines (optional). Snap the door
to the door clips when power
and data lines have been run.
12. Carefully
worksurface
appropriate
of the adjoin
worksurface
to attach the
worksurface
at this time
power & data
module
leg plug
leg set
vertical
wireway-inner
vertical
wireway-outer
(end-of-run)
Figure 4
13. Unclip a
power/data
worksurface
under the ad
surface. Sec
the leg set o
worksurface
Route the tra
through con
vertical wire
adjoining rec
snap the co
harness (Fig
Note: All tab
securely fas
connections
installed.
vertical
wireway cap
Figure 4
24
11. Secure t
drilled holes
adjoining rec
two #12 x 1
Note: This channel is not to
be used for routing extension
cords. Power supply cords
are not to be routed across or
through more than one complete
unit/worksurface.
adjustable
glide
14. Route th
cord through
hole in the w
module into
15. From un
the power/d
power cord
the 10-wire
operation of
To open, pu
it will pop up
®
WorkZone® Desks - “810” 10-Wire
Electrical
System
DataLink
Training
Table Syste
ble System - "810" 10-Wire Electrical System
Instructions
AssemblyAssembly
Instructions
Assemble units as described assemble
herein only.
To do
units
as otherwise
described herein on
may result
in instability .
may result in instability. All screws,
nuts and
bolts mustallbescrews, nut
and must
tightened securely and must tightened
be checkedsecurely
periodically
after be check
assembly . Failure to assemble properly, o
assembly. Failure to assemble properly, or to secure parts
result in assembly failure and personal in
may result in assembly failure and personal injury.
ed herein only . To do otherwise
l screws, nuts and bolts must be
ust be checked periodically after
ble properly, or to secure parts may
d personal injury .
ge
ire
2
0
2
2
0
2
2
0
2
2
0
2
2
0
2
2
0
120/240V SINGLE PHASE
CIR.1
CIR.2
CIR.3
DEAD M ETAL
BLACK (LINE 1)
PINK (LINE 4)
W HITE/RED (NEUTRAL 4,5)
GREEN/YELLOW OR GRAY (ISOLATED GROUND 4,5)
GREEN OR BARE (GROUND 1,2)
W HITE/BLACK (NEUTRAL 1,2)
RED (LINE 2)
TAN (LINE 5)
DO NOT CONNECT BLUE (LINE 3)
DO NOT CONNECT ORANGE (LINE 6)
CIR.4
120/208V W YE (THREE PHASE)
CIR.1
CIR.5
CIR.2
CIR.6
CIR.3
6-2-2
DEAD M ETAL
BLACK (LINE 1)
PINK (LINE 4)
W HITE/RED (NEUTRAL 4,5 & 6)
GREEN/YELLOW OR GRAY (ISOLATED GROUND 4,5 & 6)
GREEN OR BARE (GROUND 1,2 & 3)
W HITE/BLACK (NEUTRAL 1,2 & 3)
RED (LINE 2)
TAN (LINE 5)
BLUE (LINE 3)
ORANGE (LINE 6)
CIR.4
CIR.5
CIR.6
6-2-2 connection Diagrams
120/240V SINGLE PHASE
CIR.1
810-Universal Wire connection
Diagrams
have a certified electrician hard-wire the
panel power infeed to the building power
source according to the national electrical
code and any other applicable local codes .
See the chart for proper wiring connection
to available power .
CIR.2
receptacles
available
Wires to be used
gauge
of wire
circuit 1
black
White/black Letters
green or bare
12
10
12
circuit 2
red
White/black Letters
green or bare
12
10
12
circuit 3
blue
White/black Letters
green or bare
12
10
12
circuit 4i
Pink
White/Purple Letters
green/yellow Stripe
or gray
12
10
Tan
White/red Letters
green/yellow Stripe
or gray
12
10
orange
White/red Letters
green/yellow Stripe
or gray
12
10
CIR.3
DEAD M ETAL
BLACK (LINE 1)
PINK (LINE 4)
W HITE/RED (NEUTRAL 4)
GREEN/YELLOW OR GRAY (ISOLATED GROUND 4)
GREEN OR BARE (GROUND 1,2)
W HITE/BLACK (NEUTRAL 1,2)
DO NOT CONNECT RED (LINE 2)
DO NOT CONNECT TAN (LINE 5)
BLUE (LINE 3)
DO NOT CONNECT ORANGE (LINE 6)
circuit 5i
circuit 6i
2
CIR.4
120/208V W YE (THREE PHASE)
CIR.1
CIR.5
CIR.2
CIR.6
6
12
12
12
CIR.3
DEAD M ETAL
BLACK (LINE 1)
PINK (LINE 4)
W HITE/RED (NEUTRAL 4)
GREEN/YELLOW OR GRAY (ISOLATED GROUND 4)
GREEN OR BARE (GROUND 1,2 & 3)
W HITE/BLACK (NEUTRAL 1,2 & 3)
RED (LINE 2)
DO NOT CONNECT TAN (LINE 5)
BLUE (LINE 3)
DO NOT CONNECT ORANGE (LINE 6)
6-2-2 connection Diagrams to an 8-Wire building
CIR.4
CIR.5
CIR.6
6
20
25
WorkZone® Transitional Worksurface - Square/Rectangular Surface
Assembly Instructions
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
WorkZone Transitional Worksurface
Square/Rectangular Surface
splice
plates
#12 x 1" screw
#10 x ½" screw
Tools Required
• Phillips Screwdriver
• Level
primary
worksurface
1. Attach two-splice plates to the
pre-drilled mounting holes under
the primary worksurface with four
#12 x 1” screws, two screws per
splice plate. Repeat the procedure
for splice plates to the return
worksurface (Figure 1).
2. To avoid scratching the
transitional worksurface, place
the top face down onto a soft
protective surface (Figure 2).
26
#12 x 1"
screw
1. Attach tw
mounting ho
worksurface
screws per
procedure fo
worksurface
2. To avoid
worksurface
soft protecti
Figure 1
Figure 1
3. Position the corner leg over the
pre-drilled holes in the back
corner of the worksurface. Be
sure the modesty panel mounting
holes are oriented as shown.
Attach the corner leg to the
worksurface with four #12 x 1”
screws. Do not tighten at this
time (Figure 2).
4. Align one modesty panel to the
corner leg and worksurface
mounting holes. Insert two
#10 x ½” screws through the
modesty panel and into the
corner leg. Attach modesty panel
to worksurface with two
#12 x 1” screws. Do not tighten
at this time. Repeat this step for
second modesty panel. Tighten
all screws attaching the corner
leg and the modesty panels
(Figure 2).
return
worksurface
Tools Requi
Phillips Sc
Level
corner leg
adjustable
glide
#12 x 1" screw
#10 x 1/2" screw
modesty panel
#12 x 1"
screw
#12 x 1" screw
square
transitional
worksurface
Figure 2
Figure 2
3. Position t
holes in the
Orient the co
of the corne
modesty pa
corner leg to
#12 x 1” sc
(Figure 2).
4. Align one
and worksu
#10 x ½” s
panel and in
modesty pa
x 1” screws
Repeat this
Tighten all s
and the mod
WorkZone® Transitional Worksurface - Square/Rectangular Surface
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
5. Position the primary and return
work surfaces as illustrated,
set the square or rectangular
transitional surface onto the
splice plates, and attach the
transitional surface to the splice
plates with eight #12 x 1”
screws, two per splice plate from
underneath (Figure 3).
square/rectangular
transitional
surface
#10 x ½"
screw
modesty panel
splice plate
primary
worksurface
return
worksurface
transitional
leg set
Figure
Figure 33
#12 x 1"
screw
6. Align the modesty panel mounting
holes of the transitional surface
to the transitional leg sets of the
primary and return worksurfaces,
then secure together using two
#10 x ½” screws per modesty
panel and leg set (Figure 3).
7. To level the worksurfaces, turn the
adjustable glides either in or out.
The jambnuts between the
adjustable glides and the bottom
of the leg sets must be tightened
up against the bottom of the leg
to secure the adjustable glides.
Note: In a step down installation,
use a Z-bracket (not shown)
instead of splice plates.
Z-brackets are installed in the
same manner as splice plates.
27
WorkZone® Peninsula Worksurface - Side Mouting
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Assembly Instructions
WorkZone Peninsula Worksurface
Side Mounting
#12 x 1" screw
#10 x ½" screw
#1
Tools Required
• Phillips Screwdriver
• Level
1. Set the peninsula worksurface
face down onto a soft
protective surface. Attach the
single leg to the peninsula
worksurface with four #12 x 1”
screws (Figure 1).
2. Align the corner leg with
the pre-drilled holes in the
peninsula worksurface at the
corner opposite from where
the peninsula will attach
the adjoining rectangular
worksurface. Be sure that the
modesty panel mounting holes
on the corner leg face inward
for mounting of the modesty
panel next (Figure 1).
3. Position the side-mount
modesty panel under the
peninsula and align mounting
holes to holes in corner leg.
Secure modesty panel to
corner leg with two #10 x ½”
screws. Attach the modesty
panel to the peninsula with two
#12 x 1” screws (Figure 1).
4. Install a leg plug into each
of the two exposed holes in
the corner leg as illustrated
(Figure 1).
28
#1
1
#10 x /2"
screw
side mount
modesty panel
Tools Required
Phillips Screwd
Level
adjustable
glide
corner
leg
#12 x 1"
screw
leg
plug
#12 x 1"
screw
adjustable
glide
single
leg
peninsula
worksurface
Figure 1Figure 1
#12 x 1"
screw
1. Set the peninsu
onto a soft protec
single leg to the p
four #12 x 1” sc
2. Align the corne
holes in the penin
corner opposite f
will attach the adj
worksurface. Be
mounting holes o
inward for mount
next (Figure 1).
3. Position the sid
under the peninsu
holes to holes in
panel to corner le
screws. Attach th
peninsula with tw
(Figure 1).
4. Install a leg plu
exposed holes in
(Figure 1).
WorkZone® Peninsula Worksurface
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
5. Secure two splice plates to the
mounting holes at the underside
of the adjoining rectangular
worksurface. Use four #12 x 1”
screws, two per splice plate
(Figure 2).
Note: Transitional leg sets can be
identified by their shorter, floorlevel foot, for less restricted user
movement.
ula Worksurface
es to the
derside of the
ksurface. Use
o per splice
1
#10 x /2"
screw
s can be
floor-level foot,
ovement.
peninsula
worksurface
nsula
. Set the
to position on
e mounting
nsula to the
eath with four
r splice plate
nel of the
the transitional
crews (Figure 2).
splice
plate
#12 x 1"
screw
Figure 22
Figure
adjoining
rectangular
worksurface
transitional
leg set
6. Carefully turn the peninsula
worksurface right side up. Set
the peninsula worksurface into
position on the splice plates.
Align the mounting holes and
secure the peninsula to the
worksurface from underneath with
four #12 x 1” screws, two per
splice plate (Figure 2).
7. Attach the modesty panel of the
peninsula worksurface to the
transitional leg with two #10 x ½”
screws (Figure 2).
8. Level the peninsula worksurface
by turning the adjustable glides
on the single leg and the corner
leg either in or out (Figure 1).
rksurface by
des on the single
her in or out
29
WorkZone® Peninsula Worksurface - Center Mounting
Assembly Instructions
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
WorkZone Peninsula Worksurface
Center Mounting
Tools Required
• Phillips Screwdriver
• Level
#12 x 1" screw
1. Set the peninsula worksurface
face down onto a soft
protective surface. Attach the
single leg to the peninsula
worksurface with four #12 x 1”
screws (Figure 1).
#10 x ½" screw
center mount
modesty panel
2. Position the center mount
modesty panel onto the
peninsula, over the modesty
panel mounting holes.
Attach the modesty panel to
peninsula with two #12 x 1”
screws (Figure 1).
3. Secure two splice plates to
the mounting holes at the
underside of each adjoining
rectangular worksurface. Use
two #12 x 1” screws per splice
plate (Figure 2).
#12 x 1"
screw
Tools Req
Phillips
Level
leg
adjustable
leveler
glide
single
leg
#12 x 1"
screw
peninsula
worksurface
2. Positio
panel ont
panel mo
panel to p
screws (F
Figure
Figure
1 1
3. Secure
holes at t
rectangul
screws p
Note: Transitional leg sets can
be identified by their shorter,
floor-level foot, for less
restricted user movement.
adjoining
rectangular
worksurface
4. Carefully turn the peninsula
worksurface right side up. Set
the peninsula worksurface into
position on the splice plates.
Align the mounting holes and
secure the peninsula to the
worksurface from underneath
with eight #12 x 1” screws,
two per splice plate (Figure 2).
6. Level the peninsula
worksurface by turning the
adjustable glide on the single
leg either in or out (Figure 1).
30
Note: Tra
by their s
restricted
transitional
leg
#10 x 1/2"
screws
splice
plate
peninsula
worksurface
5. Attach the modesty panel of the
peninsula worksurface to the
transitional legs with two
#10 x ½” screws per side of
the center mount modesty
panel (Figure 2).
adjoining
rectangular
worksurface
splice
plate
#12 x 1"
screw
Figure 2
Figure 2
1. Set the
onto a so
single leg
four #12
transitional
leg set
4. Carefu
right side
into posit
mounting
the works
#12 x 1”
(Figure 2)
5. Attach
worksurf
#10 x ½
mount m
6. Level t
turning th
either in o
WorkZone® Peninsula Worksurface - End Mounting
Assembly Instructions
Assembly Instructions
WorkZone Peninsula Worksurface
Assemble units as described herein only. To do otherwise
End Mounting
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
#12 x 1" screw
#12 x 1" screw
#10 x ½" screw
1
#10 x /2" screw
leg
leveler
single
leg
#12 x 1"
screw
peninsula
worksurface
FigureFigure
1
1
Tools Required
ToolsScrewdriver
Required
Phillips
• Phillips Screwdriver
Level
• Level
Note: Read through all instructions
Note:
Readbeginning
through allassembly.
completely
before
instructions
completely
before
End-mount
peninsula
assembly
has two
assembly.
types ofbeginning
installation
depending upon if the
End-mount
peninsula
assembly
peninsula
worksurface
attaches
to the side
has two types
of installation
of a rectangular
worksurface
(Figure 2) or
upon
if the peninsula
the frontdepending
edge of the
worksurface
(Figure 3).
worksurface attaches to the side
of apeninsula
rectangular
worksurface face down
1. Set the
worksurface
(Figure
2) or thesurface.
front edge
of thethe
onto a soft
protective
Attach
worksurface
(Figure
3).
single leg to the peninsula worksurface with
four #12 x 1” screws (Figure 1).
1. Set the peninsula worksurface
face down onto
a soft protective
Note: End-mount
peninsula
worksurfaces
surface.
Attach
single
leg adjoining
to
that attach
to the
frontthe
edge
of the
the peninsula
worksurface
rectangular
worksurface
(Figure with
3) requires
four
x 1” screws
(Figure Refer
1). to
a reverse
in #12
assembly
procedure.
steps 2 and 3 but install the two splice plates
Note: End-mount
peninsula
to the peninsula
worksurface
first, instead of
worksurfaces
that attach
to
the adjoining
rectangular
worksurface.
Also,
the
front
edge
of
the
adjoining
the peninsula worksurface must be
rectangular
positioned
up into worksurface
place with splice plates
3) requires
reversethrough
in
installed,(Figure
so marks
can bea made
the
assembly holes
procedure.
Referthe
to
splice mounting
and onto
steps
andfront
3 butedge
install
underside,
at 2the
of the
thetwo
adjoining
splice plates
to the
peninsula
worksurface.
The four
holes
must be
instead
carefullyworksurface
drilled to afirst,
depth
of 1” then the
of the
adjoining rectangular
peninsula
worksurface
can be installed to
worksurface.
Also, the peninsula
the rectangular
worksurface
(Figure 3).
worksurface must be positioned
up into place with splice plates
installed, so marks can be made
through the splice mounting
holes and onto the underside, at
the front edge of the adjoining
worksurface. The four holes must
be carefully drilled to a depth of
1” then the peninsula worksurface
can be installed to the rectangular
worksurface (Figure 3).
31
WorkZone® Peninsula Worksurface
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
securelyWorksurface
and must be checked periodically after
WorkZonetightened
Peninsula
assembly. Failure to assemble properly, or to secure parts
5. Position two
splice
to mounting
may
resultplates
in assembly
failure and personal injury.
holes at the underside of the adjoining
rectangular worksurface. Secure splice
plates to worksurface with four #12 x 1”
screws, two per splice plate (Figure 2).
2. Position two splice plates to
mounting
holes atset
thethe
underside
3. Carefully
peninsula
of the
adjoining
rectangular
worksurface into position on the splice
worksurface.
Secure
platesholes and
plates. Align
thesplice
mounting
to worksurface
four to the worksurface
secure thewith
peninsula
#12 from
x 1” screws,
two per
splice
underneath
with
four #12 x 1”
platescrews,
(Figure 2).
two per splice plate (Figure 2).
peninsula
worksurface
side
edge
3. Carefully
set the
4. Level
thepeninsula
peninsula worksurface by
worksurface
into
position onglide
the on the single
turning the adjustable
splice
plates.
Align
the
mounting
leg either in or out (Figure 1).
holes and secure the peninsula to
the worksurface from underneath
with four #12 x 1” screws, two
per splice plate (Figure 2).
4. Level the peninsula worksurface
by turning the adjustable glide
on the single leg either in or out
(Figure 1).
splice
plate
adjoining
rectangular
worksurface
#12 x 1"
screw
Figure
2
Figure 2
adjoining
rectangular
worksurface
peninsula
worksurface
splice
plate
front
edge
#12 x 1"
screw
Figure 3
Figure 3
32
Assembly Instructions
WorkZone Conference End Worksurface
WorkZone® Conference End Worksurface
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
#12 x 1" screw
Tools Required #12 x 1" screw
Phillips Screwdriver
Level Tools Required
leg
leveler
#12 x 1"
screw
single
leg
• Phillips Screwdriver
1. Set the
• conference
Level end worksurface face
down onto a soft protective surface. Attach
the single
peninsula
1. leg
Set to
thethe
conference
endworksurface
with four #12
x
1”
screws
(Figure
1).a
worksurface face down onto
soft protective surface. Attach
2. Align twothesplice
mounting
singleplates
leg to to
thethe
peninsula
holes at theworksurface
underside with
of the
adjoining
four #12 x 1”
worksurface.
Secure
the 1).
splice plates to the
screws
(Figure
worksurface with four #12 x 1” screws, two
per splice
2).plates to the
2. plate
Align (Figure
two splice
conference end
worksurface
Figure 1
Figure 1
splice
plates
adjoining
worksurface
#12 x 1"
screw
mounting holes at the underside
3. Turn the ofconference
endworksurface.
right-side-up and
the adjoining
set it carefully
onto
splice
plates
of the
Secure
thethe
splice
plates
to the
adjoining worksurface.
Align
the
mounting
worksurface with four
holes of the#12
splice
pre-drilled
x 1” plates
screws,with
two the
per splice
holes in theplate
conference
end. Secure with
(Figure 2).
four #12 x 1” screws, two per splice plate
(Figure 3).
3. Turn the conference end
right-side-up and set it carefully
4. Level theonto
conference
worksurface
by
the spliceend
plates
of the
turning the adjoining
adjustable
glide
on
the
single
leg
worksurface. Align
either in or the
outmounting
(Figure 1).
holes of the splice
plates with the pre-drilled holes
in the conference end. Secure
with four #12 x 1” screws, two
per splice plate (Figure 3).
Figure 2
Figure 2
conference end
worksurface
4. Level the conference end
worksurface by turning the
adjustable glide on the single leg
either in or out (Figure 1).
adjoining
worksurface
#12 x 1"
screw
Figure 3
Figure 3
33
WorkZone® Guest Modesty Panel
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Tools Require
Phillips Scr
1. Set the wo
modesty pane
protective sur
#12 x 1" screw
Tools Required
• Phillips Screwdriver
#12 x 1"
screw
1. Set the worksurface to receive
guest modesty panel upside
down onto a soft protective
surface (Figure 1).
2. Position the guest modesty
panel over pre-drilled holes in
underside of worksurface and
secure using six #12 x 1” screws
(Figure 1).
piano
worksurface
3. Carefully turn the worksurface to
the upright position
(Figure 1).
Figure
Figure
1 1
34
2. Position the
pre-drilled ho
and secure us
(Figure 1).
guest
modesty panel
3. Carefully tu
upright positio
Assembly Instructions
WorkZone Mobil Tables - Tear Drop & Semi Circle
®
WorkZone Mobil Tables
Assembly Instructions
Tear Drop & Semi-Circle
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
#12 x 1" screw
#12 x 1" screw
caster
leg
locking
caster
#12 x 1”
screw
worksurface
Figure
TearDrop
Drop
Worksurface
Figure 11- -Tear
Worksurface
locking
caster
leg
caster
Tools Required
Tools Required
Phillips •Screwdriver
Phillips Screwdriver
1. Set the 1.worksurface
upside upside
down
Set the worksurface
onto a soft protective
surface.
Attach
down onto a soft protective
three leg setssurface.
to worksurface
Attach threebottom
leg sets to
by aligning legs
to pre-drilled
worksurface
bottomholes
by aligning
and insertinglegs
eight
#12 x 1” holes
screws
to pre-drilled
and
per leg set (Figure
1 &eight
2). #12 x 1” screws
inserting
per leg set (Figure 1 & 2).
2. Install casters on the bottom of
each leg by
threading
intoonholes
on of
2. Install
casters
the bottom
the undersideeach
of each
Locking
leg byleg.
threading
into holes
casters on Tear
Drop
table should
on the
underside
of eachbeleg.
placed on theLocking
two legs
on the
casters
on curved
Tear Drop
portion of thetable
worksurface
(Figureon1).the
should be placed
Locking casters
on Semi-Circle
two legs
on the curvedtable
portion
should be placed
the two legs
on 1).
of the on
worksurface
(Figure
the flat portion
of thecasters
worksurface
Locking
on Semi-Circle
(Figure 2). table should be placed on the
two legs on the flat portion of the
3. Carefully turn
the worksurface
worksurface
(Figure 2).to
the upright position (Figure 1 & 2)
3. Carefully turn the worksurface to
the upright position.
#12 x 1”
screw
worksurface
Figure 22- -Semi-Circle
Worksurface
Figure
Semi - Circle
Worksurface
35
KI
1330 Bellevue Street
P.O. Box 8100
Green Bay, Wisconsin 54308-8100
1-800-424-2432
www.ki.com
Ki is a registered trademark
of Krueger International, Inc.
© 2012 KI
All Rights Reserved
Litho in USA.
Code KI-60456R4/KI/GT/1112
">