Goldacres Traymount 400L Operator's & Parts Manual

GA8700742 REV4 DEC 19

1

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Goldacres Warranty Statement . . . . . . . . . . . .10

General Information & Specifications . . . . . . . .11

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Key Features . . . . . . . . . . . . . . . . . . . . . . . . .14

Vehicle Mounting . . . . . . . . . . . . . . . . . . . . . .15

First Time Start Up . . . . . . . . . . . . . . . . . . . . .15

Honda GX200 & Delta 40 Pump . . . . . . . . . . .16

Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Pump Maintenance . . . . . . . . . . . . . . . . . . . .22

Pump Troubleshooting . . . . . . . . . . . . . . . . . .23

Suction Filter . . . . . . . . . . . . . . . . . . . . . . . . .24

Filling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Spray Application . . . . . . . . . . . . . . . . . . . . . .25

Flushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Traymount 200L - Tank & Frame . . . . . . . . . . .26

Traymount 300-400L - Tank & Frame . . . . . . .27

Traymount 200-400L - Hose Reel . . . . . . . . . .28

Traymount 200-400L - Suction Filter . . . . . . . .29

Traymount 200-400L - Pump . . . . . . . . . . . . .30

Traymount 600L - Tank & Frame . . . . . . . . . . .31

Traymount 600L - Pump & Drain . . . . . . . . . . .32

Traymount 600L - Hose Reel & Suction Filter .34

Spray Gun - GunJet AA30L . . . . . . . . . . . . . .36

Spray Gun - Nozzle . . . . . . . . . . . . . . . . . . . .37

Pump - Delta 40 . . . . . . . . . . . . . . . . . . . . . . .38

Gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Suction Filter Assembly . . . . . . . . . . . . . . . . . .41

Pressure Control Unit . . . . . . . . . . . . . . . . . . .42

Contact

Goldacres

1-3 Morang Crescent,

Mitchell Park Vic 3355

P: 03 5342 6399

F: 03 5342 6308 [email protected]

Disclaimer

Any advice or recommendations given by Goldacres, Goldacres’ dealers, or employees is given in good faith and provided based on the best information available to us. No liability or responsibility is accepted or implied as a result of any information or advice tendered in this operating manual or by Goldacres its agents or employees. The end user accepts all responsibility arising from that advice. No part of this manual may be reproduced without written permission from Goldacres.

All photographs and technical information remain the property of Goldacres.

2

Introduction

Congratulations on your purchase of a

Goldacres sprayer. For more than a quarter of a century Goldacres has supplied

Australian farmers with quality, innovative and technologically advanced spraying solutions - equipment designed in Australia for Australian conditions.

Goldacres not only produce Australia’s finest range of spraying equipment - we also keenly value the unique relationship we enjoy with owners of our equipment. We are pleased to welcome you as a Goldacres owner and look forward to making your spray applications as efficient as possible.

Please use this comprehensive resource to gain a full understanding of your equipment, and don’t hesitate to contact your Goldacres

Dealer or Goldacres for further information.

Roger Richards

General Manager

3

Safety

General

The following pages outline important safety information. At Goldacres safety is a high priority. These safety and warning instructions MUST be followed to ensure the safe operation of your Goldacres equipment.

Explanation of key terms used in this operator’s manual are:

DANGER - You will be killed or seriously hurt if you don’t follow instructions

WARNING - You can be seriously hurt if you don’t follow instructions

CAUTION - You can be hurt if you don’t follow instructions

NOTE - Is used to notify people of installation, operation or maintenance information that is important but not hazard related.

The Operator

All operators of this equipment should be adequately trained in the safe operation of this equipment. It is important that all operator’s have read and fully understand the operators manual prior to using this equipment.

All new operators should be trained in an area without bystanders or obstructions and become familiar with the sprayer prior to operation.

Safety Precautions

WARNINGS

• Keep clear of overhead obstructions.

• CRUSH HAZARD - Keep hands clear of moving parts.

• Any unauthorised modifications to this equipment may affect its function and create a serious safety risk.

• Never attempt to clean parts or nozzles, by blowing with mouth.

• Never attempt to siphon chemicals, or substances, by sucking.

• It is imperative that the vehicle manufacturer’s specifications be checked and all instructions for use when transporting be adhered to at all times.

• Care should be taken when transferring liquid into the tank to ensure that the gross weight of the equipment does not exceed the carrying, braking and/or towing capacity of the vehicle to which the equipment is attached as specified by the vehicle manufacturer.

NOTE: 1 LITRE WATER = 1KG.

• Water weighs 1kg per litre, however conversion factors must be used when spraying liquids that are heavier or lighter than water. Example: liquid urea has a density of 1.28 kg/L and will therefore be significantly heavier than water if the tank is filled completely.

• Suitable care should be taken when driving with the equipment attached to the vehicle. Consideration should be given to both the carrying capacity of the vehicle and the gradient of the terrain when determining the speed at which the vehicle can be driven safely.

• Ensure that the maximum speed of the vehicle, when loaded, is within the vehicle manufacturers limitations.

• Ensure equipment is securely fastened, or attached to the vehicle at all times.

• Regularly check the pump mounting bolts. The pump will always vibrate to some degree when operating, and this may work the bolts loose.

CAUTIONS

• A supply of fresh water should be with the equipment at all times.

• Standard polyethylene tanks are not designed for use with diesel fuel or any flammable liquid.

• Do not use this machine in ambient temperatures exceeding 40 degrees

Celsius.

• Ensure that all bolts are tightened and secured before operation.

• Area surrounding equipment may become slippery when wet.

Continued over page

4

NOTES

• Always read and understand the operator’s manual prior to operation of this equipment.

• It is the responsibility of the operator to ensure that there are no decals missing from the equipment and that any damaged or missing decals are replaced prior to operation.

• Goldacres equipment ordered or operated, outside the guideline limitations may not be warranted by

Goldacres for successful performance.

Operators working outside these limitations do so at their own risk, unless specific advice has been sought from and provided by Goldacres in writing.

• Always read and follow the chemical manufacturer’s guidelines for safe application as per the chemical label.

Particular attention should be given to the recommended target application rate of the chemical being applied as per the chemical label.

• Inspect the equipment thoroughly for damage and wear before operation.

• Flush chemicals from equipment immediately after use.

• Certain chemicals may be unsuitable for use with Goldacres standard plumbing designs. Consult your Goldacres dealer if in doubt.

• Do not operate the equipment while under the influence of any drugs, alcohol or if excessively tired.

• Make sure that the equipment complies with all relevant road regulations when transporting.

• When draining fluids from the equipment use appropriate, leak proof containers.

Do not use food or beverage containers as someone may consume the contents by mistake.

• After reading the operator’s manual if there is any thing that you do not understand please contact your

Goldacres dealer.

Safe Chemical Use

The safe use of Ag chemicals with this equipment is the responsibility of the owner/ operators. All operators should be trained in the safe use of Ag chemicals. Goldacres suggest that a relevant course is completed by owners/operators prior to operation of this equipment as a spray unit.

Personal Protective Equipment (PPE)

Always wear close fitting clothing and safety equipment designed for the job.

Chemicals can be harmful to humans, appropriate PPE should be used when handling chemicals.

Always refer to the chemical manufacturers label for guidelines on the appropriate PPE to use with the chemicals you are using.

Goldacres also suggest that you read and understand the following Australian standards:

• Australian Standard for Chemical protective clothing AS3765

• Australian Standard for Respiratory protection devices AS1715

Airborne particles

Always stand well clear of equipment during operation. Any spray drift is dangerous and may be hazardous to humans and animals.

Fluids under pressure

Do not disconnect any hoses, nozzles or filters while equipment is operating.

Disconnecting these components while under pressure may result in uncontrolled fluid discharge which may be hazardous.

When the repair is complete ensure that all fittings and lines are secured before reapplying pressure.


5

Cuts, Stabs & Punctures

When Servicing machine, be mindful of sharp edges on parts such as trimmed cable ties, hose clamps, cut reinforced hose and the edges of plates and brackets as they could cause cut, stab or puncture injuries.

Mount Vehicle Safety

• Consult your vehicle operator’s manual before mounting this sprayer.

• Do not fit the spray tank to the front of your vehicle.

• Fully read the Owner’s Manual before mounting this spray unit to vehicle.

• Before mounting to a vehicle ensure that fitment complies with weight restrictions as specified by vehicle manufacturer.

• Overloading the vehicle, or operating it improperly, may cause an accident, injury or death.

• Do not load the vehicle in excess of the load limit capacity of the vehicle as recommended by the manufacturer.

• Filling the spray tank when fitted to the vehicle will result in changes to the handling and stability of the vehicle.

• Vehicle tyres should be inflated to the manufacturers recommended operating pressures.

• Do not attach other equipment to the vehicle spray tank. This may exceed the vehicle spray tank’s designed capacity and function.

• Reduce speed when operating the vehicle spray tank when tank is loaded.

• Allow for greater braking distances when the vehicle spray tank is loaded.

• To reduce possible vehicle instability it is recommended the vehicle be stationary if spot spraying on a slope or hill.

• Ensure the vehicle or vehicle complies with all relevant regulations for use on farm or public roads.

• The weight of the unit significantly increases when filled to the maximum recommended level. Remember: 1 litre of water = 1 kilogram.

• The tank should be empty during attachment or removal of the tank from the vehicle.

• Do not allow any other person to ride on the vehicle at the same time this vehicle spray tank is fitted.

• Do not allow use of this sprayer by minors.

• Do not use the sprayer in the vicinity of other people or animals.

DANGER: Failure to adhere to these recommendations or follow these rules may result in injury or death to the operator and/or bystanders.

Anyone involved in the use or operation of the vehicle and vehicle spray equipment should be aware of, and trained in appropriate safety recommendations including those contained in this manual.

6

Safety Decals

Understanding safety decals and their purpose assists in the safe operation of your sprayer. Safety decals are there for your protection and it is the responsibility of the owner operator to replace damaged and/or missing safety decals.

Regularly review safety decals with operators. It is very important to ensure that all new machine components and replacement parts include current hazard identification decals.

Replacement safety decals can be ordered from all Goldacres dealers.

Traymount 200 Decal Kit

GA8700507


GA8700508

7



GA8700509


GA8700510

GA8700438 600L Traymount Pro-Reel site tube

GA8700438

8

Warranty

How to make a warranty claim

In the event of a fault or breakdown with your product, that you believe to be a warranty issue, the following steps must be taken.

1. Ensure that you have read the

Operator’s Manual and gone through the troubleshooting procedure.

2. If you continue to experience problems then please contact your local authorised

Goldacres dealer. They will advise the method of warranty service for your product.

Warranty Duration

Goldacres' standard warranty is 12 months from date of purchase.

Warranty Inclusions

• Chassis

• Steel Boom Components

• Tanks

• Electrical wire and connectors, (non- contaminated)

• Consoles and controllers

• Electrical motors and drivers

• Wheels, tyres and rims

• Pins and bushes*

• Pump housing

• Hydraulics

• Axle frame only

• Shockers and dampeners

• Wire cables

• Springs

• Drive chains*

• Wheel bearings*

*Failure caused by lack of lubrication not covered.

Warranty Exclusions

• Pump diaphragms

• Pump Seals

• Pump check valves

• Pump O-rings

• Filters and filter screens

• Filter O-rings

9

• Chemical Hoses

• Solenoid Diaphragms

• Hand Gun, lance or wand seals and

O-rings

• Consumables, chemicals, fuels

• Items controlled by or fitted to Non

Genuine parts or devices

• Contamination or corrosion of components

• Hose reel seal sand O-rings

• Pressurised sprayer seals and O-rings

• Belts, couplings

• Adjustment of components

• Brake pads and components

• Globes / Bulbs

• Fuses

• Oil / fluids / filters (Unless contaminated or lost due to a warrantable failure)

• Boom break away tips

• Boom break away hinges

• Boom protectors

• Nozzles

• Nozzle Bodies

• Nozzle Body Brackets

• Nozzle Diaphragms and seals

• Wiper Blades

• Skid plates

• Wear plates

• Damaged items

• Worn or wearing items

This warranty is the only warranty applicable to

Goldacres new products (Products) and to the maximum extent as permitted by law, is expressly in lieu of any other conditions or warranties expressed or implied in relation to the Product.

In Australia, Goldacres Products come with guarantees that cannot be excluded under the

Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

This Warranty gives you additional protection for your Goldacres product and identifies a preferred approach to resolving warranty claims which will be the quickest and simplest for all parties subject to the exclusions, terms and conditions below.

Goldacres warrants its authorized Dealers who in turn warrants the original purchaser (Owner) that each new Goldacres Product will be free from proven defect in materials and workmanship for twelve (12) months from the date of delivery to the first owner according to conditions outlined herein.

Subject only to legislative obligations to the contrary, Goldacres shall not be liable for incidental or consequential damage resulting from ownership or use of a Product.

Goldacres does not authorize any person to create for it any other obligation or liability in connection with these products.

The repair of the defective Product qualifying under this warranty will be performed without charge for labour and parts by any authorized Goldacres service outlet within a reasonable time following the delivery of the Product, at the cost of the owner, to the service outlet / place of business advised

Goldacres in its absolute discretion may choose to pay the cost of replacement or repair of the product.

If the Product will be repaired or replaced, using parts as supplied by Goldacres, repair may include, at Goldacres discretion, the replacement of parts with functionally equivalent remanufactured, reconditioned or new parts.

Goldacres may request failed parts to be returned to the factory.

Conditions of Warranty Coverage

The warranty covers only conditions resulting directly from defects in workmanship or materials used under normal use and service conditions.

The Warranty is not transferable.

The owner is responsible for the performance of regular maintenance and service as specified in the owner’s / operators manual applicable to the product. Failure to follow regular maintenance as

Goldacres Warranty Statement

advised may invalidate the warranty.

The owner must provide the Goldacres Dealer with prompt written notice of the defect (within 14 days of it occurring) and allow reasonable time for repair and/or replacement.

Goldacres warranty cover excludes:

• Claims resulting from misuse, use of incompatible chemical or fluids, exceeding the

Product’s specifications including overloading, impact damage, negligence, accidental damage or failure to perform recommended service or service intervals or use the Product with good care.

• Failure due to faulty or inadequate electrical sources of power. 12 volt power sources must be checked for suitability to operate the product.

• The time taken to remove and re-install warranted parts, products or components fitted to other than Goldacres brand products will not be covered by Goldacres Warranty. Only labour and parts directly attributable to the repair of the

Goldacres unit is covered.

• The cleaning of parts or products before or after the warranty repair. Cleaning time is considered a customer expense.

• Any Goldacres Product which has been repaired by other than an authorized Goldacres dealer in a way which, in the sole and absolute judgment of

Goldacres, adversely affects its performance or reliability.

• The replacement of maintenance items such as diaphragms, batteries, belts, etc.

• Loss of time, inconvenience, loss of use of the product, liability to third parties or any other consequential damages including damage to crops, profits or revenue, other commercial losses inconvenience or cost of rental or replacement equipment.

• Incidental costs associated with a warranty repair including any travel costs, out of hours labour charges, transportation costs, freight costs or any communications costs.

• Goldacres products purchased at auction or in used condition.

Procedure for claiming:

Claims must be made through a Goldacres Dealer.

To make a claim under this Warranty, you should

• Contact your local Goldacres Dealer,

• Phone 1300 301 853 to locate a Goldacres

Dealer.

Owners returning products to a Goldacres Dealer will require the original Dealer tax invoice, a copy of the tax invoice or delivery docket and any instruction manuals, information booklets or guides that were shipped with the Product.

10

B

C

D

A

1

E

F

1 2

2

General Information &

Specifications

The tray mount sprayer is ideal for small acreage and hard to get areas.

Traymount sprayers feature an engine driven diaphragm pump with a maximum pressure output of 560 Psi.

The 30 metre hose reel is fitted with a quality pistol grip spray gun with adjustable nozzle.

Know Your Sprayer

Getting to know your sprayer prior to operation is crucial in the safe and efficient operation of this equipment. Take the time to familiarise yourself with all the standard and optional components fitted to your sprayer, not only do you need to know where key components are located on your machine you need to become competent in the correct operation of these components prior to spraying operation.

It is also important to become familiar with common spraying methods and common spraying terms prior to using this sprayer for the first time.

Chassis

1030

The chassis is an all steel construction. The chassis is shot blasted, primed and then protected by the Goldacres paint process for excellent chemical resistance and durability.

Tank

All tanks are constructed from UV resistant polyethylene. Polyethylene tanks have a very high chemical resistance.

Due to the rotomoulding process, there can be a variance in the overall dimensions of the tank which in turn results in variations to the tank capacity. For this reason, calibration markings should be used as a guide only.

Filtration

Filtration is a critical part of the sprayer’s performance.

A suction filter between the tank and the pump handles filtration. It is important that the filter is cleaned out regularly.

4

Pump

The pump is critical to any sprayer performance. Correct operation and maintenance of the pump will ensure the sprayer is able to perform to its capabilities.

Always flush pump with clean water after every use. Prolonged chemical contact can severely damage valves, diaphragms and seals.

Do not leave water in pump if sprayer is to be left in a cold environment. The water may freeze and cause damage to pump. Empty pump of all water and cover the pump to ensure this situation does not arise. If this has not been done, and there is a possibility there may be frozen water in the pump, wait until any ice has thawed before using the pump.

Machine limitations

All Goldacres equipment is subject to operating limitations, it is the operator’s responsibility to ensure that this equipment is being operated within these limitations and appropriately to the operating conditions at hand.

5

REVISIONS

Paint Colours

Steel work: G13 Dark Green

06

DESCRIPTION

PSR 2 24 - BOM U

Identification

When ordering parts or requesting service information for your sprayer, it is important to quote the serial number and the purchase date of your machine. This will assist with receiving the most accurate information. The location of the stamped ID plate is shown below.

DATE

29/03/2019

6

ECN N°

1084

A

C

B

D

3

11

F

T

- P

- F

1 1/4 SUCT 1150

1 1/4 SUCT 450

DRAIN HOSE 3/4 PRESSURE 520

E

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN MILLIMETRES


0. ± 1 ANGULAR ± 0.50°

0.0 ± 0.5

0.00 ± 0.25

MATERIAL

:

MATERIAL NOT

SPECIFIED

SURFACE FINISH:

-

WEIGHT:

98.46 KG

THIS DRAWING REMAINS THE PROPERTY

OF GOLDACRES TRADING PTY LTD AND IS

SUBJECT OF COPYRIGHT

4

DEBURR AND BREAK

SHARP EDGES

-

DRAWN BY:

JAMES P

8/09/2015

MODEL EDITED BY:

NEALHARVEY

NEALHARVEY

25/11/2019

DRAWING CHECKED BY:

-

5

TITLE:

1-3 MORANG CR. MITCHELL PARK.

VICTORIA 3355 AUSTRALIA

PH: 03 5342 6399

TRAYMOUNT 400L, SUIT FLATBASE TANK WITH

30M HOSE REEL

DRAWING NUMBER:

GA4914025

REV

06

SHEET

A3

DO NOT SCALE DRAWING SHEET 5 OF 6

6

F

F

E

B

D

C

A

6

F

F

6 5 4 3 2

F

1

1

F

E

D

6

C

6

B

E

D

A

D

C

F

E

B

C

F

C

B

B

B

A

A

6

A

E

E

D

D

6

5

6

6

5

6

6

1030

Dimensions

1030

1030

E

1030

5

5

5

5

4

4

5

1030

1030

D

D

D

4

4

3

01

REV.

3

01

REV.

2

See Sheet1

DESCRIPTION

REVISIONS

01

REV.

2

See Sheet1

1

20/12/2016

DATE ECN N°

2

See Sheet1

DESCRIPTION

REVISIONS

F

1

20/12/2016

DATE

J.W

ECN N°

F

DATE

1

20/12/2016 J.W

ECN N°

F

E

E

C

B

C

C

B

B



4

MATERIAL

:

Traymount 300L

DRAWN BY:

JAMES P


0. ± 1 ANGULAR ± 0.50°

0.0 ± 0.5

0.00 ± 0.25




-

SURFACE FINISH: MODEL EDITED BY:

NEALHARVEY

25/11/2019

DRAWING EDITED BY:

TITLE:


WEIGHT:

98.29 KG

SHARP EDGES

-

0. ± 1 ANGULAR ± 0.50°

0.0 ± 0.5

0.00 ± 0.25

DEBURR AND BREAK

-

NEALHARVEY

25/11/2019

DRAWING CHECKED BY:




0. ± 1 ANGULAR ± 0.50°

0.0 ± 0.5

0.00 ± 0.25

2




3

-

-

MATERIAL

:

TRAYMOUNT, 200L, DELTA 40, GX200, 30M

WEIGHT:

98.29 KG

HOSE REEL AND AA30 GUN

DEBURR AND BREAK

SHARP EDGES

-

WEIGHT:

98.29 KG

DEBURR AND BREAK

SHARP EDGES

C

DRAWN BY:

JAMES P

E



D

D

MODEL EDITED BY:

NEALHARVEY

25/11/2019

GA4914015

-

MODEL EDITED BY:

NEALHARVEY

SHEET 5 OF 5

25/11/2019

DRAWING EDITED BY:

NEALHARVEY

25/11/2019

-

DRAWING CHECKED BY:

2

TITLE:

TITLE:

REV

TRAYMOUNT, 200L, DELTA 40, GX200, 30M

A

D

C

SHEET

A3



PH: 03 5342 6399


DRAWING NUMBER:

GA4914015

DRAWING NUMBER:

DO NOT SCALE DRAWING

GA4914015

1

REV

SHEET 5 OF 5

REV

SHEET 5 OF 5

SHEET

A3

SHEET

A3

A

A

B

12



0. ± 1 ANGULAR ± 0.50°

0.0 ± 0.5

0.00 ± 0.25

4




3

4



MATERIAL :

-

-


0. ± 1 ANGULAR ± 0.50°

0.0 ± 0.5

0.00 ± 0.25

JAMES P

MODEL EDITED BY:

NEALHARVEY

3




3

MATERIAL

-

-

:

92.60 KG

2

TITLE:

WEIGHT:

92.60 KG

DEBURR AND BREAK

SHARP EDGES

-


-

DEBURR AND BREAK

SHARP EDGES

-

NEALHARVEY

25/11/2019

:

DRAWING CHECKED BY:

-

0. ± 1 ANGULAR ± 0.50°

0.0 ± 0.5

0.00 ± 0.25

SURFACE FINISH:

DEBURR AND BREAK

SHARP EDGES

-

DRAWN BY:

JAMES P

MODEL EDITED BY:

NEALHARVEY

DRAWING EDITED BY:

NEALHARVEY

DRAWING CHECKED BY:

-

DRAWING NUMBER:

DRAWN BY:

JAMES P

8/09/2015

25/11/2019

25/11/2019

8/09/2015

MODEL EDITED BY:

NEALHARVEY

25/11/2019

DRAWING EDITED BY:

NEALHARVEY

25/11/2019

DRAWING CHECKED BY:

-


2

2

TITLE:

TITLE:



PH: 03 5342 6399


30M HOSE REEL

PH: 03 5342 6399 DRAWING NUMBER:


REV SHEET

00

SHEET 5 OF 5

1

A3

GA4914020

A

1

1

REV

00

SHEET 5 OF 5

SHEET

A3



PH: 03 5342 6399


30M HOSE REEL

DRAWING NUMBER:


GA4914020

REV

00

SHEET 5 OF 5

SHEET

A3

B

A

A

C

B

E

E

F

F

A

B

C

D

E

F

1

1

A

A

B

1

2

1

1030

2

3

2 1030

3

4

3

REV.

06

4 5

REVISIONS

5

DESCRIPTION

REVISIONS

REV.

06

PSR 2 24 - BOM U

4

PSR 2 24 - BOM U

DATE ECN N°

29/03/2019

5

1084

A

REVISIONS

REV.

06

DESCRIPTION

PSR 2 24 - BOM U

B

DATE

29/03/2019

DATE

29/03/2019

6

6

ECN N°

1084

A

ECN N°

1084

A

B

1030

B

C

C

D

F

D

E

F

E

E

F

E

D

C

B

A

F

D

C

B

6

A

6

1

2

1

6

6

B

C

C

5

1200

2

3

2

5

1200

D

4 2 1

4 3 2




0. ± 1 ANGULAR ± 0.50°

0.0 ± 0.5

0.00 ± 0.25

3




4

3

MATERIAL

:

SURFACE FINISH:

-

MATERIAL NOT

SPECIFIED

WEIGHT:

98.46 KG

1 1/4 SUCT 1150

1 1/4 SUCT 450

H R 1/2 PRESSURE 1200


JAMES P

0.0 ± 0.5

0.00 ± 0.25

NEALHARVEY

8/09/2015

TITLE:

DEBURR AND BREAK

SHARP EDGES

-



-

NEALHARVEY

25/11/2019

DRAWING CHECKED BY:

4

5

F

T

T


0. ± 1 ANGULAR ± 0.50°

0.0 ± 0.5

0.00 ± 0.25




4

- P

- F

PR 3/4 PRESSURE 900

MATERIAL

:

SURFACE FINISH:

-

MATERIAL NOT

SPECIFIED

WEIGHT:

PH: 03 5342 6399


30M HOSE REEL


SPECIFIED

SURFACE FINISH:

-

98.46 KG

DEBURR AND BREAK

SHARP EDGES

WEIGHT:

98.46 KG

DEBURR AND BREAK

SHARP EDGES

-

JAMES P

MODEL EDITED BY:

NEALHARVEY

DRAWN BY:

JAMES P

8/09/2015

25/11/2019

DRAWING EDITED BY:

NEALHARVEY

DRAWING CHECKED BY:

-

GA4914025

F

T

H

T

- P

- F

R 1/2 PRESSURE 1200

PR 3/4 PRESSURE 900

DRAIN HOSE 3/4 PRESSURE 520

TITLE:

F

T

H


REV

SHEET 5 OF 6

8/09/2015

MODEL EDITED BY:

NEALHARVEY

25/11/2019

DRAWING EDITED BY:

NEALHARVEY

25/11/2019

DRAWING CHECKED BY:

-

5

6

5

TITLE:

- F

R

1 1/4 SUCT 1150

1 1/4 SUCT 450

30M HOSE REEL

DRAWING NUMBER:


06

SHEET

A3



PH: 03 5342 6399

GA4914025

SHEET 5 OF 6

6

6

REV

06

SHEET

A3


30M HOSE REEL

DRAWING NUMBER:




PH: 03 5342 6399

GA4914025

REV

06

SHEET 5 OF 6

SHEET

A3

E

F

D

E

F

Traymount 600L

C

D

1

F

E

D

C

NOTE: Dimensions are approximate only. They may be subject to change without notice.

5

5

13

4

F

E

D

C

Model Net Weight

GA4914015 - 200L - kg

GA4914020 - 300L - kg

GA4914025 - 400L 124 kg

GA4914030 - 600L 157 kg

B

B

4




0. ± 1 ANGULAR ± 0.50°

0.0 ± 0.5

0.00 ± 0.25

0.0 ± 0.5

3

MATERIAL

:

SURFACE FINISH:

WEIGHT:

KG


SHARP EDGES




DRAWN BY:

JACK W

MATERIAL

:

10/11/2016

MODEL EDITED BY:

NEALHARVEY

DEBURR AND BREAK

KG

DRAWING EDITED BY:

NEALHARVEY

DEBURR AND BREAK

SHARP EDGES

10/11/2016

MODEL EDITED BY:

25/11/2019

DRAWING CHECKED BY:

2

TRAYMOUNT, 600L, DELTA 40 , GX200, 30M

25/11/2019



25/11/2019

DRAWING NUMBER:

TITLE:



PH: 03 5342 6399

GA4914030

DRAWING NUMBER:


1



REV

04

GA4914030

A3

A

REV

04

SHEET 5 OF 5

SHEET

A3

3 2 1

A

Key Features

5

4

3

2

7

6

Number Description

1 Main Tank

2

3

4

5

Pressure control unit

Bypass unloader lever

Main Tank Lid

30m Hose Reel

8


6 Main Tank Drain

7

8

9

Suction Filter

Pump & Motor

Wet Sight Tube

1

9

14

Sprayer Transport

Make sure the vehicle has sufficient lifting and braking capacity to carry the sprayer.

All relevant transport regulations must be adhered to when transporting the sprayer i.e. speed regulations, oversize signs, flashing light, etc. It is the operator’s responsibility to know the relevant regulations. Make sure the sprayer is securely attached to the vehicle as shown below.

CAUTION: Take care when reversing the vehicle with the sprayer attached. If driver visibility is restricted use another adult, with a clear view to the rear of the sprayer, to give reversing directions.

CAUTION: It is the operator’s responsibility to know the tare weight and gross weight of the sprayer.

Contact Goldacres dealer to ascertain a more precise tare weight for your sprayer if unsure.

If any alterations are made to the sprayer, it is the operator’s responsibility to know the tare weight and the gross weight of the modified sprayer at all times.

Vehicle Mounting

The Traymount sprayers have been designed for carrying by a suitably rated vehicle.

WARNING: Read and understand the vehicle mounting safety section at the beginning of this manual.

1. Remove from pallet (if attached) and position on a solid, flat surface.

2. Use a forklift, or other suitably rated lifting device, to lift the sprayer to a height suitable for the vehicle. Use support legs to fix the unit at this height.

3. Mount the Tray Mount to your vehicle.

Use the reverse of the procedure above to remove the Tray Mount from the vehicle.

First Time Start Up

CAUTION: Before using this equipment with a chemical mix, read and understand, the instructions on the chemical label. A first time start up procedure should be carried out as a water test only without any chemical present in the tank.

1. Inspect the sprayer to ensure there is no damage or wear which could lead to injury, further damage or reduce its performance.

2. Check all bolts and nuts to make sure they are tight and secure.

3. Carry out scheduled lubrication.

4. Make sure the sprayer is securely attached to the vehicle

6. Ensure all filters and nozzles are clean.

7. Fill main tank with approximately 10% of total tank volume of fresh water.

8. Move the bypass unloader lever on the pressure control unit outwards to allow the engine to start with no load.

9. Start the engine at the lowest revs possible and then gradually increase revs until the pump reaches your desired operating speed.

IMPORTANT: The reduction gearbox operates at 6:1 ratio from engine to pump. The spray pump speed should not exceed 540 RPM.

Engine speed should not exceed 3250 RPM.

10. Move the bypass unloader lever inwards to allow spray pressure to reach the gunjet.

Ensure that the spray gun outlet valve on the pressure control unit is open.

11. Check spray gun operation. If there are irregularities, clean the nozzle or tighten fittings as necessary.

12. Check all other components are operating correctly and make any adjustments as necessary.

NOTE : For optimal sprayer set-up, the operator needs to be aware of the correct nozzle and correct speed at which to travel when spraying. For this information, refer to the TeeJet catalogue and your chemical manufacturer’s information for determining appropriate spray rates or consult an agronomist for further help.

15

Honda GX200 & Delta 40 Pump

12

13

16

14

15

10

9

8

7

6

5

1

3

4

2

11

• 6.5 HP Honda GX200 Engine

• 6:1 Reduction Gearbox

• 2 Diaphragms

• 40 L/min @ 540 RPM

• 560 PSI / 39 Bar

Key Features


1 Relief valve adjuster

2 Bypass unloader lever

6

7

8

3

4

5

Bypass outlet back to spray tank

Inlet from spray tank

Spray pressure gauge

Spray pressure outlet 1

Spray pressure outlet 2

Spray pump air damper

16


9 Spray pump diaphragm housing

10 Reduction gearbox

14

15

16

11

12

13

Spray pump oil drain plug

On / Off switch

Fuel tank

Air cleaner

Exhaust muffler

Engine oil cap / Dipstick

37Z4V6100.fm 3 ページ２０１８年１０月４日　木曜日　午後１時５４分

Engine

The Traymount sprayers are fitted with a

Honda GX200 motor as standard. It may be optioned with an electric starter. This section provides a basic overview of motor features and operation only. For detailed safety, operating and maintenance instructions specific to this motor consult the Honda owner's manual supplied or find a copy online.

Engine Safety

• Understand the of all controls and learn how to stop the engine quickly in case of emergency.

• Do not allow children to operate the engine.

Keep children and pets away from the area of operation.

• Your engine's exhaust emits poisonous carbon monoxide. Do not run the engine without adequate ventilation, and never run the engine indoors.

• The engine and exhaust become very hot during operation. Keep engine away from flammable materials and do not place anything on engine while it is running.

Preoperational Safety Check

1. Look around the underside of the engine for signs of any oil or fuel leaks.

2. Remove any excessive dirt or debris, especially around the muffler and recoil starter.

3. Look for signs of damage.

4. Check that all shields are in place, and that all nuts, bolts and screws are tightened.

Preoperational Maintenance Check

1. Check engine oil level. Running with low oil can cause damage.

Where fitted, the oil alert system will automatically stop the engine before the oil level becomes critically low.

2. Check reduction gearbox oil level.

Sufficient oil level is essential to maximise gearbox life.

3. Check air filter element and clean or replace as necessary to allow clear airflow to the carburetor.

COMPONENT & CONTROL LOCATIONS

FUEL FILLER CAP

FUEL TANK

OIL DRAIN PLUG

MUFFLER

SPARK PLUG

FEATURES

OIL ALERT

®

SYSTEM (applicable types)

‘‘Oil Alert is a registered trademark in the United States’’

The Oil Alert system is designed to prevent engine damage caused by an insufficient amount of oil in the crankcase. Before the oil level in the crankcase can fall below a safe limit, the Oil Alert system will automatically stop the engine (the engine switch will remain in the ON position).

If the engine stops and will not restart, check the engine oil level

(see page 8) before troubleshooting in other areas.

ELECTRIC STARTER

(applicable type)

OIL FILLER CAP/DIPSTICK

AIR CLEANER

CIRCUIT PROTECTOR (applicable types)

The circuit protector protects the battery charging circuit. A short circuit, or a battery connected with reverse polarity, will trip the circuit protector.

RECOIL STARTER

The green indicator inside the circuit protector will pop out to show that the circuit protector has switched off. If this occurs, determine the cause of the problem, and correct it before resetting the circuit protector.

CIRCUIT

PROTECTOR

Push the circuit protector button to reset.

STARTER GRIP

FUEL VALVE LEVER

ENGINE CONTROL TYPES

EXCEPT ELECTRIC STARTER

TYPES

CHOKE LEVER

THROTTLE LEVER

ENGINE

SWITCH

ENGINE SWITCH

ELECTRIC STARTER TYPES

CHOKE LEVER

(air cleaner low profile type)

CIRCUIT

PROTECTOR

ENGLISH

ON

OFF

3

17



OPERATION

IS YOUR ENGINE READY TO GO?

SAFE OPERATING PRECAUTIONS

BEFORE OPERATION CHECKS

FEATURES regulations, and to maximize the service life of your equipment, it is very important to take a few moments before you operate the

OPERATION

SAFE OPERATING PRECAUTIONS

BEFORE engine to check its condition. Be sure to take care of any problem regulations, and to maximize the service life of your equipment, it is very important to take a few moments before you operate the engine to check its condition. Be sure to take care of any problem you find, or have your servicing dealer correct it, before you operate the engine.

correct a problem before operation, could result in a significant malfunction.

Failure to properly maintain this engine, or failing to

Circuit Protector

battery charging circuit. A short

If the motor has been optioned with electric start, then it will also have a circuit protector fitted which protects the battery charging circuit. A short circuit, or a battery connected with reverse polarity, will trip the circuit protector.

Carbon Monoxide Hazards by an insufficient amount of oil in the crankcase. Before the oil level in the crankcase can fall below a safe limit, the Oil Alert system will automatically stop the engine (the engine switch will cause illness or death.

BEFORE

OPERATION CHECKS on page 4.

monoxide gas that can collect rapidly in an enclosed area and

For your safety, do not operate the engine in an enclosed area such as a garage. Your engine’s exhaust contains poisonous carbon monoxide gas that can collect rapidly in an enclosed area and

Exhaust contains poisonous carbon monoxide gas that can build up to dangerous levels in closed areas.

Exhaust contains poisonous carbon monoxide gas that can build up to dangerous levels in closed areas.

MUFFLER

RECOIL STARTER level and the engine switch is in the OFF position.

protector will pop out to show that the circuit protector has switched off. If

Always check the following items before you start the engine:

Breathing carbon monoxide can cause unconsciousness or death.

Never run the engine in a closed, or even partly closed this engine for any safety precautions that should be observed with

The green indicator inside the circuit protector will pop out to show that the circuit protector has switched off. If this occurs, determine the

2. Remove any excessive dirt or debris, especially around the resetting the circuit protector.

3. Look for signs of damage.

Push the circuit protector button to reset.

1. Move the fuel valve lever to the ON position.

STARTING THE ENGINE

OFF FUEL VALVE LEVER


Starting Engine


1. Check the fuel level (see page 8). Starting with a full tank will

FUEL VALVE LEVER

ON

OFF

ON

2. Check the engine oil level (see page 8). Running the engine with a low oil level can cause engine damage.

37Z4V6100.fm ページ２０１８年１０月４日　木曜日　午後１時５４分

OFF

ON position.

2. If the engine is cold, move the choke lever to the CLOSED position.

The Oil Alert system (applicable types) will automatically stop the engine before the oil level falls below safe limits. However,

2. To start a cold engine, move the choke lever to the CLOSED position.

to avoid the inconvenience of an unexpected shutdown, always

If restarting a warm engine, leave the choke lever in the OPEN position.

9). Oil is essential to reduction case operation and long life.

performance.

CLOSED

3. Move the throttle lever away from the MIN. position, about 1/3 of the way toward the MAX. position.

3. Move the throttle lever approximately 1/3 of the way from the MIN. position.

THROTTLE LEVER position.

MIN.

MAX.

MIN.

5. Operate the starter.

RECOIL STARTER:

Pull the starter grip lightly until you feel resistance, then pull briskly in the direction of the arrow as shown below. Return the starter grip gently.


STARTER GRIP

RECOIL STARTER:


Review the instructions provided with the equipment powered by this engine for any precautions and procedures that should be followed before engine startup.

4. Turn the engine switch to the ON

4 position.

Some engine applications use a remote-mounted choke control rather than the engine-mounted choke lever shown here. Refer

3

MAX.

4. Turn the engine switch to the ON position.

to the instructions provided by the equipment manufacturer.

EXCEPT ELECTRIC

STARTER TYPES


Some engine applications use a remote-mounted throttle control rather than the engine-mounted throttle lever shown here. Refer

Direction to pull

STARTER GRIP

Do not allow the starter grip to snap back against the engine.

Return it gently to prevent damage to the starter.

4

18

EXCEPT ELECTRIC

STARTER TYPES

ON

ENGINE SWITCH

ON


ON

ON

ON

ON

ON

ENGINE SWITCH

ENGINE SWITCH

Turn the key to the START position, and hold it there until the engine


If the engine fails to start within 5

ELECTRIC STARTER (applicable types): least 10 seconds before operating the and hold it there until the engine starts.

Using the electric starter for more than 5 seconds at a time will overheat

START

START

START least 10 seconds before operating the starter again.

When the engine starts, release the key, allowing it to return to the ON position.

ENGINE SWITCH

(applicable types) the starter motor and can damage it.

6. If the choke lever was moved to the CLOSED position to start the engine, gradually move it to the OPEN position as the engine warms up.


ENGINE SWITCH

(applicable types)

CHOKE LEVER


CLOSED

CHOKE LEVER

OPEN

OPEN

CLOSED

OPEN

ENGLISH

5

ENGLISH

5






THROTTLE LEVER


RECOIL STARTER: briskly in the direction of the arrow as shown below. Return the starter grip gently.



Pull the starter grip lightly until you feel resistance, then pull

THROTTLE LEVER

1. Operate the starter:

RECOIL STARTER

MIN.

MIN.


MAX.

RECOIL STARTER:


1/3 POSITION


STARTER GRIP

• Pull the starter grip lightly until you feel resistance, then pull briskly in the direction of the arrow as shown below. Return the starter grip gently.

1/3 POSITION


NOTE:

EXCEPT ELECTRIC



Do not allow the starter grip to snap prevent damage to the starter.



4. Turn the engine switch to the ON position.

ON

EXCEPT ELECTRIC

ELECTRIC STARTER

• ON

ENGINE SWITCH

ON


Turn the key to the START position, and hold it there until the engine starts.

and hold it there until the engine starts.

ON


Turn the key to the START position, and hold it there until the engine starts.

If the engine fails to start within 5 seconds, release the key, and wait at least 10 seconds before operating the

ON and hold it there until the engine seconds, release the key, and wait at

START

START

• When it starts, release the key, allowing it to return to the ON position.

NOTE: Using the starter for longer than 5 seconds at a time will overheat the motor and start within 5 seconds, release the key, and wait at least 10 seconds before trying the starter again.

ENGINE SWITCH

2. If the choke lever was moved to the

CLOSED position to start the engine, gradually move it to the OPEN position as the engine warms up.



START least 10 seconds before operating the starter again.

Using the electric starter for more than 5 seconds at a time will overheat seconds, release the key, and wait at can damage it. This type of overheating is not covered under warranty. If the engine fails to the starter motor and can damage it.

This type of overheating is not covered under warranty.

the starter motor and can damage it.

This type of overheating is not key, allowing it to return to the ON position.

ENGINE SWITCH

(applicable types) the starter motor and can damage it.



ENGINE SWITCH

When the engine starts, release the key, allowing it to return to the ON the engine, gradually move it to the OPEN position as the

ENGINE SWITCH

(applicable types)

CHOKE LEVER engine warms up.

OPEN

CHOKE LEVER

STOPPING THE ENGINE

CLOSED

OPEN

To stop the engine in an emergency, simply turn the engine switch to the OFF position. Under normal conditions, use the following procedure. Refer to the instructions provided by the equipment manufacturer.

Position the throttle lever for the desired engine speed.

CLOSED

OPEN

Some engine applications use a remote-mounted throttle control rather than the engine-mounted throttle lever shown here. Refer to

Setting Engine Speed

OPEN

1. Move the throttle lever to the MIN. position.

Some engine applications use a remote-mounted throttle control

Move the throttle lever to somewhere between the MAX. and MIN. position to set desired engine speed.

For engine speed recommendations, refer to the instructions provided with the equipment powered by this engine.

ENGLISH

THROTTLE LEVER

IMPORTANT: The reduction gearbox operates at a 6:1 ratio from the engine to the pump.

The spray pump speed should not exceed

MIN.

ENGLISH

540 RPM. Therefore the engine should not be allowed to run over 3250 RPM.

MIN.

MAX.

MIN.

5

MAX.

MIN.

MAX. 3250 RPM

5

5

2. Turn the engine switch to the OFF position.

EXCEPT ELECTRIC

STARTER TYPES


OFF

ENGINE SWITCH

19

OFF

OFF

OFF

ENGINE

SWITCH

3. Move the fuel valve lever to the OFF position.

FUEL VALVE

LEVER

OFF

OFF

ON

6

ENGLISH

Stopping Engine




STOPPING THE ENGINE SETTING ENGINE SPEED

To stop the engine in an emergency, simply turn the engine switch

To stop the engine in an emergency, simply turn the engine switch to the OFF position. Under normal conditions, use the following manufacturer.

manufacturer.



Some engine applications use a remote-mounted throttle control rather than the engine-mounted throttle lever shown here.

Position the throttle lever for the desired engine speed.


Some engine applications use a remote-mounted throttle control the instructions provided by the equipment manufacturer.

the instructions provided by the equipment manufacturer.

For engine speed recommendations, refer to the instructions

For engine speed recommendations, refer to the instructions provided with the equipment powered by this engine.

MAX.

MIN.

MIN.

MAX.

MIN.


EXCEPT ELECTRIC

STARTER TYPES

STARTER TYPES


OFF

ENGINE SWITCH

OFF

OFF

MIN.

OFF


ENGINE

SWITCH

SWITCH


FUEL VALVE

LEVER

LEVER

OFF

EMERGENCY SHUTDOWN: Turn the engine switch to the OFF position.

The full shutdown procedure should be followed during normal operation.

6

OFF

ON

ENGLISH

20

Pump

Diaphragm pumps are a positive displacement pump that utilise a number of rubber diaphragms and non-return check valves to pump (displace) the fluid. Diaphragm pumps are very well suited to chemical spraying applications. To ensure that you get the most from your pump, follow the information here to use it correctly. Proper operation and periodic maintenance are essential in obtaining the best possible performance from your sprayer over time.

PRESSURE RELIEF VALVE

The pressure relief valve provides relief when the pressure exceeds a pre-determined value and is part of the pressure control unit.

Turning the adjuster clockwise will increase the pressure relief setting and vice versa. The pressure gauge gives indication of the delivery pressure to the spray gun.

BYPASS VALVE

The bypass valve enables all pump delivery to bypass back to the tank. The bypass valve is part of pressure control unit. It should be opened when starting the pump with an engine so that the engine does not start under load. The bypass valve should also be engaged to agitate the tank mixture when not spraying. To engage the bypass valve, pull the valve lever out. This will cause all pump delivery to be bypassed back to the tank. To disengage the bypass valve, push the valve lever in, so that the pump delivery is directed out to the spray lines.

IMPORTANT: Never overfill pump with oil as damage to seals & oil bowl may result. Do not operate diaphragm pumps above 540 RPM.

IMPORTANT: The pump will perform optimally close to, but not over 540 RPM. At speeds much below 540 RPM, excessive pulsation will occur. Speeds above 540 RPM are likely to result in pump and diaphragm damage.

IMPORTANT: Do not leave water in pump if sprayer is to be left in a cold environment.

Frozen water inside the pump can cause the housing to crack. Always allow any frozen water inside the pump to thaw before attempting to operate the pump.

PREOPERATIONAL PROCEDURE

1. If sprayer is in a cold environment, make sure that any frozen water present in the pump is thawed before attempting operation to avoid serious damage.

Ensure that the pump can be turned over by hand before starting.

2. Inspect all hoses to make sure they are the correct size, fitted securely and that there is no restriction or leaking.

3. Make sure that the pump PTO shaft cover is fitted correctly to prevent accidental injury.

4. Make sure the strainer in the suction filter is clean and correctly installed.

5. Lubricate the PTO shaft according to manufacturer recommendations to prevent the shaft from binding.

6. Change the pump oil after the first 50 hours of operation and then after every

300-350 hours. Use only SAE 30W40 motor oil and do not overfill. Rotate pump manually (by hand) to remove air locks when filling with oil.

WHEN THE PUMP IS OPERATING

• The oil should be visible in the bowl.

• Frequently check the oil level and colour.

IMPORTANT: A change in either colour or level indicates probable damage to diaphragm or valves. Stop the pump immediately.

POST OPERATIONAL PROCEDURE

1. Always flush pump with clean water at the end of each spraying day. Prolonged chemical contact can severely damage seals and diaphragms.

2. Do not leave water in pump if sprayer is to be left in a cold environment. Frozen water inside the pump can cause the housing to crack. Empty pump of all water and run it dry for 15-20 seconds

Then cover pump with a bag or similar to keep it protected. If this has not been done and there is a possibility there may be frozen water in the pump and/or in the lines, wait until any ice has completely thawed before using pump again.

21

Pump Maintenance

The pump diaphragms are wearing components that need to be replaced during the life of the pump. Life expectancy depends upon pump operation and maintenance and task suitability.

MAINTENANCE GUIDELINES

• Pump diaphragms should be replaced prior to diaphragm failure.

• Where the sprayer is used extensively, the pump should be reconditioned once a season, including replacing diaphragms, seals and valve springs.

• It is recommended to keep a spare pump repair kit (including diaphragms, seals, valve o-rings and springs) on hand in case of a breakdown.

• A change of oil colour indicates a pump problem. The oil should be regularly monitored when spraying so that any problem is detected as soon as possible.

If the oil goes milky in colour, it is likely the diaphragm has split and the spray mixture has come into contact with the oil. If the oil goes black (or dark grey), it is likely the pump has overheated.

MAIN CAUSES OF PREMATURE

DIAPHRAGM FAILURE

• Blocked or incorrectly fitted suction filter restricting flow to the pump.

• Incorrect air damper chamber pressure.

• Running pump at speeds greater than 540

RPM.

• Exceeding the 560 PSI pressure limit of the pump.

• Failure to wash chemicals from pump after use.

• Incompatibility of the diaphragm material and the chemicals used.

DIAPHRAGM REPLACEMENT

When diaphragms require replacement it is normal practice to replace the air damper diaphragm at the same time.

1. Flush pump with clean water to remove chemical residue, then flush with appropriate decontaminating agent (refer to chemical label for decontamination instructions).

2. Run pump dry for 15-20 seconds to remove water.

3. Remove all air from air damper chamber by pushing in air valve.

4. Remove pump from sprayer.

5. Remove pump manifolds and pump heads.

IMPORTANT: Carefully note the position and orientation of all heads, manifolds and valves when disassembling pump. Failure to reassemble correctly will result in severe pump damage.

6. Drain oil from pump.

7. Remove diaphragms.

8. Remove cylinder sleeves.

9. Flush inside of pump with diesel.

10. Visually inspect inner workings of pump.

11. Reassemble with correct new diaphragms only once satisfied with condition of pump.

12. Refill with oil (SAE 30W40). Rotate pump by hand to remove air locks. Do not overfill.

22

Pump Troubleshooting

The troubleshooting information is provided as a reference when your sprayer is not functioning correctly.

Problem Common Causes

To ensure that you receive the best possible service, it is recommended that you exhaust all applicable troubleshooting solutions shown prior to calling your dealer, or Goldacres, for service advice.

Common Solution

Excessive bypass on regulator Check regulator setting on pump.

Pressure and flow rate are too low

Pressure and flow rate are too high

Bypass from regulator is restricted or blocked

Suction filter may be blocked

Check tank sump and suction line blockages

Check suction line for air leaks

Check pump speed

Check oil for colour change. If the oil appears milky, a diaphragm will be damaged and needs to be replaced.

Check valves in pump.

Check for restriction in bypass

Adjust pump speed, close to, but no higher than 540 rpm (3250 rpm engine).

The pressure on my gauge is higher than the nozzle flow indicates

The flow rate is correct but my pressure is too low or high.

Blocked filter or nozzle

Flow loss due to resistance in lines, fittings and/or nozzle.

Spray gun nozzle

Pressure fluctuation

Pump pressure pulsating

Check and clean pressure line, fittings and nozzle

Check nozzle on spray gun for type and fitment

Air leak on suction side of pump Check suction pump for air leaks

Incorrect pump speed

Adjust pump speed, close to, but no

Faulty pump valves

Air accumulator pressure is incorrect

Air accumulator diaphragm has a leak higher than 540 rpm (3250 rpm engine).

Replace pump valves

Add or remove air in accumulator as necessary

Replace air accumulator diaphragm

Pump speed too low

Adjust pump speed, close to, but no higher than 540 rpm (3250 rpm engine).

Air leak on suction side of pump Check pump suction for air leaks

Pump oil becoming black or dark grey

Supply to pump is restricted

Pump is overheating Check pump speed and oil level

Pump is noisy

Pump housing or mountings cracked

Low oil level

Air accumulator pressure set incorrectly

Insufficient lubrication

Damaged pump valves

Pump suction line has air leak or is restricted

Extremely cold weather can cause liquid in the pump to freeze and expand

Refill or replace oil

Recharge air accumulator to specified pressure

Replace all bearings

Replace pump valves

Clean suction filter and check for leaks in suction lines

Water should be removed from the pump when storing in very cold environments

23

Suction Filter

It is essential to maintain all filters, and filter screens, in good condition. Filter screens that are not regularly cleaned can severely impede the flow and thus affect delivery pressure.

If the screen is in any way damaged, it can allow foreign material into the pumping system which can result in damage to the pump, lines, valves and nozzle tips. If the screen is not properly fitted, it can allow air into the pumping lines which will reduce the performance of the pump. The filter screen should be cleaned after every spraying operation. The best way to clean the filter screen is with a soft brush or compressed air after washing the entire chemical residue from the pump.

SAFETY SHUT-OFF VALVE

The safety shut off valve enables the filter bowl to be removed while automatically shutting off the supply line to the filter. As the filter bowl is removed together with the bowl cap, the valve plunger seats so as to seal off the filter from the supply line. Replacing the filter bowl unseats the valve plunger and thus opens the supply line to the filter.

SUCTION FILTER CLEANING

WARNING: Appropriate PPE must be worn when cleaning filters.

1. Ensure the pump is turned off.

2. Carefully unscrew filter nut and remove bowl and avoid contact with residual chemical.

3. Remove screen and clean (with a soft brush or compressed air).

4. Check for damage to screen, bowl,body and O-ring.

5. Place screen back in position.

6. Make sure O-ring is in position for proper seal.

7. Replace bowl and screw nut on. Do not over-tighten nut.

Filling

When filling the sprayer it is necessary to use an external water source.

WARNING : Operators must wear the appropriate PPE.

The following steps should be followed when filling the tank:

1. With sprayer mounted on the vehicle, park on level ground.

2. The pump should be turned off.

3. Remove the tank lid.

4. Add 20% of the tanks volume of clean water, or more, if the chemical is in a denser form e.g. powder.

5. Add chemical as required. Some agitation will take place as the rest of the water is added.

6. Use external water source to fill main tank

(Do not exceed the tank capacity).

7. Replace the tank lid and ensure that it is secure prior to switching on pump. You are now ready to use the sprayer.

WARNING : When filling tank with water, 1 litre of water will add 1 kg of weight. Some chemicals have a higher density than water and will weigh more per litre. Therefore, it is the operators responsibility to ensure the loaded weight of the sprayer does not exceed the towing and / or carrying capacity of the vehicle.

24

Spray Application

It is the responsibility of the operator to ensure that the chemical mix is sufficiently agitated and that the conditions are right to start spraying.

NOTE : For optimal sprayer set-up, the operator needs to be aware of the correct nozzle and correct speed at which to travel when spraying. For this information, refer to the TeeJet catalogue and your chemical manufacturer’s information for determining appropriate spray rates or consult an agronomist for further help.


1. Follow the safety checks and maintenance checks for both the engine and pump.

2. Follow the filling procedure to fill the tank.

3. Move the bypass unloader lever outwards to allow the engine to start with no load.

4. Follow the starting procedure to start engine.

5. Allow pump to build pressure. While the bypass to tank is open, the tank contents will be agitated.

6. Once agitation is complete and you are ready to commence spraying, close the tank bypass by moving the lever on the pressure regulator inwards.

7. It is recommended to set the regulator to maximum pressure of 45 PSI when using the spray gun. Adjust the regulator if necessary.

8. Ensure that the gun jet outlet valve on the pump is open and engage the trigger on the spray gun to commence spot spraying.

9. Adjust the pressure regulator to raise or lower the spray rate to suit application. This will ensure even and consistent coverage of the target.

Flushing

The following information is provided as a general guide for flushing your sprayer after a spray application

For more specific information regarding flushing, and decontamination, specific to the products that you are applying, it is recommended that you consult the chemical label or your chemical supplier.


1. Turn pump off.

2. Drain main tank by opening drain valve.

3. Add a quantity of fresh water to main tank and allow to exit through drain.

4. Close drain valve and add a quantity of fresh water along with decontaminating agents if required to main tank.

5. Turn on pump, and spray fresh water through the spray gun. This will ensure that fresh water has circulated through the pump and gun.

6. Drain remaining contents of fresh water.

and then re-close drain valve. The sprayer is now ready for storage.

Storage

If the sprayer is to be stored for a long period of time without use, there are several tasks that need to be performed.

1. Clean the sprayer thoroughly as described under “flushing”.

2. Store the sprayer out of direct sunlight and where it will not be affected by frosts.

3. Ensure that the main tank is empty.

4. Protect hoses and electrical connections.

25

C

B

A

D

F

E

6 5

12

13

14

15

10

11

8

9

16

1

18

19

ITEM NO. PART NUMBER

1

4

5

2

3

6

GA850000

GA4600305

GA50 1

GA5000999

GA500 231

GA50 08 H

H

, E

GA501122

GA50005 5

GA50005

GA50 30

GA5002 83

GA50 13

GA50 132

GA50122 3

GA5001 41

GA5018309

GA50 0

GA50 6882

GA50 6 13

H

F

, E

, 30 H

, 90

, 90

T

DESCRIPTION

, 200L, F B

R , T , 200-300-400L

H

3/4 SS

, 3/4

, 1/2

, C , 1/2

1/2

B M12 20 GR8.8 P

3/4

, B

C

V

, E

W

W

, 90

H C

P , C

, 3/4

R

12

12

S SS

F SS HD

, 1 1/4 1 1/4

, 1 1/4, SS 30-45/13W

, B

, B

, B , 12

H

F

L , T

N

W

, 1/2

, B

20

, 1/2

, 255

, 3/4

3/4

, D

1/2 3/4

F SS HD

, L

3/4 , B

, W

203 120

, B

, B

4

, HB050-90

, B

T

-

-

-

-

1

1

-

-

1

1

4

4

2

4

2

2

1

2

/ TY. D / TY.

1 -

1

-

-

-

-

-

-

-

1

1

-

2

1

1

1

1

-

1

3

04

03

02

REV.

E

U

P

,

2

BOM S A211

GX200

DESCRIPTION

REVISIONS

Traymount 200L - Tank & Frame

1

9/05/2018 J R

1

20/0 /201

9/12/2016

DATE - INITIAL

J.W

J.W

ECN N°

F

10 11

E

6

12

13

14

15

5

D

2

4

1

16

15

USE LOCTITE 55 PIPE

SEALING CORD ON ALL

PLASTIC FITTINGS

4

C

3

4

9

8

B

4

6

3 5

Pos. Part No.

-

1

0.0 ± 0.5

0.00 ± 0.25

MATERIAL

:

-

GA5076882

2 GA4600305

WEIGHT:

98.29 KG

3

4

GA5077717

GA5000999

5 GA5007231

6 GA5077708

7 GA5011227

8 GA5000575

9 GA5000577

11

GA2000209

GA8500007

10 GA5077730

GA5002783

Description

Hose, Clear, 12mm, Sight tube

SURFACE FINISH:

DEBURR AND BREAK

SHARP EDGES

MODEL EDITED BY:

Lid, Tank, 255 mm diameter, With breather

Frame, 30m Hose Reel, Traymount, 200-300-400L

DRAWING CHECKED BY:

-

Hose clamp, Cobra type, 1/2"


Hose barb, Elbow, 90 degree, 1/2" male thread x 1/2" hose

Bolt M12 x 20 GR8.8 ZP

Washer 12mm Spring SS

Washer 12mm Flat SS HD

Hose barb, Elbow, 90 degree, 1-1/4" male thread x 1-1/4" hose

Hose Clamp, 1-1/4", SS (30-45/13W)

Qty.

-

1

-

1

SHEET 2 OF 5

1

4

4

4

2

2

2

2

1

1

REV SHEET

A3

A

26

1 2 3 4

REV.

06

5

DESCRIPTION

REVISIONS

DATE

29/03/2019

6

ECN N°

1084 A A

B

D

E

F

C

Traymount 300-400L - Tank & Frame

NOTE: 400L TANK SHOWN

14

13

C

1

4 3 9 5 12

7

6

10

11 8 15 8

Pos. Part No.

GA2000209

GA8500008

1 GA8500009

GA5076880

2 GA4600305

3 GA5076259

4 GA5076604

PLASTIC FITTINGS

7 GA5000577

8

9

GA5000999

GA5002873

10 GA5011227

11 GA5077709

12 GA5078409

13 GA5077708

14 GA5007231

15 GA5077719

Description


Tank, 300L, Flat Base - Includes lid

Tank, 400L, Flat Base - Includes lid

Lid, Black, Without breather, Medium, Diameter 355 mm

Frame, 30m Hose Reel, Traymount, 200-400L

USE LOCTITE 55 PIPE

SEALING CORD ON ALL



Hose Clamp, 3/4", SS (16-27/12W)

Hose Clamp, 1 1/2", SS (32-50/12W)

3


Hose barb, Straight, 3/4" male thread x 3/4" hose

Plumbing fitting, Nipple, 1 1/2", Arag, 2502060



Hose barb, Elbow, 90 degree, 1" male thread x 3/4" hose

27

2

Qty.

1

2

4

1

2

1

2

1

4

4

1

1

1

1

1

-

-

1

ITEM NO.

1

2

3

6

7

8

9

4

5

10

11

12

13

14

15

PART NUMBER

GA8500009

GA4600305

GA5076259

GA5076604

GA5077679

GA5000575

GA5000577

GA5000999

GA5002873

GA5011227

GA5077709

GA5078409

GA5077708

GA5007231

GA5077719

DESCRIPTION

Tank, 400L, Flat Base

Frame, 30m Hose Reel, Traymount, 200-300-400L

Hose barb, Elbow, 90 degree, 1 1/2 fly nut end x 32 mm hose, Arag

Fly nut, 1 1/2, Arag

O ring, 30 x 3, G10061



3/4" SS hose clamp

1.5" SS hose clamp


Hose barb, Straight, 3/4 male thread x 3/4 hose, Banjo

Plumbing fitting, Nipple, 1 1/2", Arag, 2502060

Hose barb, Elbow, 90 degree, 1/2 male thread x 1/2 hose, Banjo, HB050-90

Hose clamp, Cobra type, 1/2

Hose barb, Elbow, 90 degree, 1 male thread x 3/4 hose, Banjo

QTY.

1

1

1

4

4

2

1

1

1

4

1

1

2

2

1

D

E



MATERIAL

:

MATERIAL <NOT

SPECIFIED>

SURFACE FINISH:


0. ± 1 ANGULAR ± 0.50°

0.0 ± 0.5

0.00 ± 0.25

-

WEIGHT:

98.27 KG




4

DEBURR AND BREAK

SHARP EDGES

-

DRAWN BY:

JAMES P

8/09/2015

MODEL EDITED BY:

NEALHARVEY

27/11/2019

DRAWING EDITED BY:

NEALHARVEY

27/11/2019

DRAWING CHECKED BY:

-

TITLE:

5



PH: 03 5342 6399


30M HOSE REEL

DRAWING NUMBER:

GA4914025

REV

06

SHEET

A3


6

F

B

1 2

A

Traymount 200-400L - Hose Reel

1 3 4 5 6 8 9 2

B

3

C

10

11

D

15

16

13

12 13 14

Pos. Part No.

1

2

3

4

5

6

7

8

9

GA5066080

GA4532190

GA5065455

GA5000117

GA5000141

GA5000335

GA5002911

F

GA5012461

10 GA5004727

11 GA5013003

12 GA4534635

13 GA5003651

14 GA5004917

15* GA4900546

16 GA5000469

Description

GA5065455

GA500011

GA5000141

GA5000335

GA5002911

GA50005

GA5012461

GA5004 2

GA5013003

GA4534635

1

R A P 5

B M10 30 GR8.8 P

W

W

DESCRIPTION

, 30 3/8 ,

Hose Reel Adaptor Plate (5mm FMS)

B M12 60 GR8.8 P

Nut M12 Nyloc ZP

W 8

N M8 N

H

35 35

End cap, Plastic, Black, Insert, RHS. 35 x 35, 1.0 - 3.0mm wall

GA4900546

GA5000469

H



Nut M10 Nyloc ZP

P

,

12

N M12 N


F SS HD

P

F SS HD

P

B M8 50 GR8.8 P

, 8 OD 60

G

F SS

P

,

, 1/2 , SS

Pipe linch pin, 8 OD x 60 mm long 2

Bracket, Gun jet, Holder support

Washer 8mm Flat SS

FMS

1/2

2

1

8

4

1

4

TY.

1

1

1

4

2

1

1

1

2

1

Nut M8 Nyloc ZP

Gunjet, AA30, 5500-X18 adjustable nozzle, 1/2" Hose Barb

Hose clamp, 1/2", SS

28

14

Qty.

1

1

2

1

1

1

2

1

3

1

4

4

2

4

8

1

1

10

11

12

4

REV.

06

5

DESCRIPTION

PSR 2 24 - BOM U

REVISIONS

DATE

29/03/2019

6

ECN N°

1084 A

USE LOCTITE 55 PIPE

SEALING CORD ON ALL

PLASTIC FITTINGS

B

1

2

3

3

4

5

C

4

2

6

5

8

9

8

9

10

11

12

13

14

15

3

4

5

6

ITEM PART NUMBER

1 GA2000106

2 GA50 6 9

GA50 603

GA50 6604

GA50028 3

S

H

GA50 6259 H

GA5000999

GA50 0 H

V

GA5018309

GA5001 41

GA50122 3

GA50 132

C

GA50 13

GA5003643

GA5004085

F

DESCRIPTION

, 1-1/2 50 M

O

T

, 1-1/2 BSP M

, G

, 30 3, G10061

, E

, S

32

, 90

, 1 1/2

, A

F

1.5 SS

, 1 1/2, A

, A

, 1 1/2

32

3/4 SS

, 1/2 3/4 , B

, B , 12

N

W

, 3/4

R

, 1/2

B

20

, B

, L

F SS HD

1/2 3/4

3/4

P , C , 3/4 , B

W 8 F SS HD

B M8 20 GR8.8 P

,



MATERIAL

:

MATERIAL NOT

SPECIFIED

SURFACE FINISH:


0. ± 1 ANGULAR ± 0.50°

0.0 ± 0.5

0.00 ± 0.25

-

WEIGHT:

98.46 KG




4

DEBURR AND BREAK

SHARP EDGES

-

DRAWN BY:

JAMES P

8/09/2015

MODEL EDITED BY:

NEALHARVEY

28/11/2019

DRAWING EDITED BY:

NEALHARVEY

28/11/2019

-

DRAWING CHECKED BY:

TITLE:

5



PH: 03 5342 6399


30M HOSE REEL

DRAWING NUMBER:

GA4914025

REV

06

SHEET

A3


6

F

1

2

2

1

TY

2

1

2

1

1

1

3

3

1

1

1

D

E

A

1 2 3 4

REV.

06

5

DESCRIPTION

PSR 2 24 - BOM U

REVISIONS

DATE

29/03/2019

6

ECN N°

1084 A

B

C

D

15

16

1 3 4 5 6

10

11

12 13 14

E

F

12

13

14

15

16

8

9

10

11


1

4

5

2

3

6

GA5066080

GA4532190

GA5065455

GA500011

GA5000141

GA5000335

GA5002911

GA50005

GA5012461

GA5004 2

GA5013003

GA4534635

GA5003651

GA500491

GA4900546 G

GA5000469

1

H

B

H

DESCRIPTION

, 30 3/8 ,

R A P 5

B M10 30 GR8.8 P

W

B M12 60 GR8.8 P

W

10

N M10 N

35 35

F SS HD

P

12

N M12 N

F SS HD

P

B M8 50 GR8.8 P

P

,

, AA30,

W 8

N M8 N

H

, 8 OD 60

G

F SS

P

,

, 1/2 , SS

2

FMS

1/2

8 9 2

USE LOCTITE 55 PIPE

SEALING CORD ON ALL

PLASTIC FITTINGS

Traymount 200-400L - Suction Filter

5

4

3

3

2

C

1

4

1

1

1

2

1

1

1

4

2

2

1

8

4

1

4

TY.

1

10

11

12

13

14

15

2

6

5

8

9

12

13

14

15

ITEM PART NUMBER

1 GA2000106

2 GA50 6 9

3 GA50 603

4

5

6

8

9

10

11

GA50 6604

GA50028 3

GA50 6259 H

GA5000999

GA50 0

GA5018309

GA5001 41

GA50122 3

GA50 132

GA50 13

GA5003643

GA5004085

S

H

H

V

C

F , 1-1/2 50 M

T

DESCRIPTION

, 1-1/2 BSP M

, G

O , 30 3, G10061

32 , S , 1 1/2

, A

F , 1 1/2, A

1.5 SS

, E

32

3/4 SS

, 1/2

, 90

, A

, 1 1/2

3/4

, L

, B

, B , 12

N

W

, 3/4

, 1/2

B

R

20

P , C

F SS HD

1/2 3/4

, B

, 3/4

3/4

, B

W 8 F SS HD

B M8 20 GR8.8 P

,

1

1

3

3

1

2

1

1

1

2

2

1

Pos. Part No.

1 GA2000106

2 GA5077679

3 GA5076037

4 GA5076604

5 GA5002873

6 GA5076259

7 GA5000999

8 GA5077707

9 GA5018309

10 GA5001741

11 GA5012273

12 GA5077132

13 GA5077137

14 GA5003643

15 GA5004085

Description


* Sub-assembly shown on following pages.

MATERIAL

:

MATERIAL NOT

SPECIFIED

WEIGHT:

DRAWN BY:

Suction Filter, 1-1/2” 50 Mesh, 1-1/2” BSP Male Threads

O ring, 30 x 3 mm SURFACE FINISH:

Hose barb, Straight, 1-1/2" fly nut end x 32mm hose

Fly nut, 1-1/2", Arag

Hose Clamp, 1 1/2", SS (32-50/12W)

Hose Clamp, 3/4", SS (16-27/12W)

Plug, Cam lever, 3/4" male



-

98.46 KG

DEBURR AND BREAK

Hose barb, Elbow, 90 degree, 1 1/2" fly nut end x 32 mm hose

Hose barb, 1/2" male thread x 3/4" hose

Valve, Ball, 12mm, 1/2” female, Lever handle, Brass


Nipple Reducing 1/2" x 3/4"

Cam lever, 3/4" female coupling x 3/4" female thread

Qty.

8/09/2015

MODEL EDITED BY:

NEALHARVEY

2

28/11/2019

DRAWING EDITED BY:

NEALHARVEY

28/11/2019

DRAWING CHECKED BY:

-

1

3

1

1

3

1

2

1

1

2

1

1

2

5

TITLE:



PH: 03 5342 6399


30M HOSE REEL

DRAWING NUMBER:

GA4914025

REV

06

SHEET

A3


6

1

TY

2

1

D

E

F

29

B

A

1 2 3 4

REV.

06

5

REVISIONS

DESCRIPTION

PSR 2 24 - BOM U

6

DATE ECN N°

A

29/03/2019 1084

B

C

E

F

D

Traymount 200-400L - Pump

1

16 1 19 18

4

15 14

C

13

12

11

10

PLACE GA50 2400 - RUBBER INSERTION

PLATE TO ACT AS VIBRATION DAMPER

9 9 8

2

3

1

Pos. Part No.

GA2000209

1 GA5023085

2 GA5072295*

3 GA5072285*

4 GA5077650*

5 GA5004917

ENGINE OIL: 10W30 - 450

GEAR OIL: 80W90 - 600

9 GA5000117

10 GA5000141

11 GA4400415

12 GA5004097

13 GA5004437

14 GA5075657

15 GA5000469

16 GA5000999

17 GA5075745

18 GA5076067

19 GA5075791

Description


Engine, GX200, 3/4” shaft, Honda

Reduction Gearbox, Ratio 6:1, S160-3/4 GR, Suit Delta 40 GR

Pump, Delta 40 GR

Pressure control unit, valve, DS3, 3 section, 30 Bar, Udor

Nut M8 Nyloc ZP





Nut M10 Nyloc ZP

Plate, Delta 40 Pump Mount


3

Washer 6mm Flat SS

Hose barb, Elbow, 90 degree, 13mm hose, including 1/2" fly nut and seal, Brass


3/4" SS hose clamp

Hose barb, Elbow, 90 degree, Fly nut end x 20mm hose

O ring, 17.13 x 2.62 mm

Fly nut, M30


6

6

5

Qty.

1

1

-

1

1

4

1

2

2

4

4

8

4


4


1

4

5

2

3

6

8

9

10

11

12

13

14

GA5023085

GA50 2295 R

GA50 2285

GA50 650

GA500491

GA5003643

GA5048655

GA5006161

GA500011

GA5000141

GA4400415

GA500409

GA500443

GA50 565

H

15

16

1

18

19

-

MATERIAL

:

MATERIAL NOT

SPECIFIED

SURFACE FINISH:

WEIGHT:

98.2 KG

GA5000469

GA5000999

GA50 5 45

GA50 606

GA50 5 91

DEBURR AND BREAK

SHARP EDGES

-

P

H

P

G

, E

DRAWN BY:

JAMES P

8/09/2015

MODEL EDITED BY:

NEALHARVEY

2 /11/2019

DRAWING EDITED BY:

NEALHARVEY

2 /11/2019

DRAWING CHECKED BY:

-

, D

, E

5

TITLE:

1

1

1

1

1

1

H

O

, R

H

3/4 SS

, 90

P

,

DESCRIPTION

6:1, S160-3/4 GR, S D

, D

3/4

40-50 GR 1

1

, 20 B , U

TY.

1

N M8 N

40 GR

, DS2, 2

W 8

P

F SS HD

B M8 40 GR8.8 P

W

B M10 25 GR8.8 P

40 P M , 200-400L

B M6 60 GR8.8 P

, 90

W

10

N M10 N

F SS HD

P

6

, 13

F SS

, B , A

, 1/2 , SS

, F

,

20

025404

, 1 .13 2.62, 110112

F , M30, U , 060426

RTV

1/2

, U ,

4

1

4

8

2

2

8

4

1

4

1

1

1

1

1

1

D

E



PH: 03 5342 6399


30M HOSE REEL

DRAWING NUMBER:

GA4914025

REV

06

SHEET

A3


6

F

30

B

6 5

F

Traymount 600L - Tank & Frame

2 3

E

4 3

REV.

02

03

04

C

2

REVISIONS

DESCRIPTION

M

M

B

BOM

1

DATE

3/08/201

8/0 /2019 JM

25/11/2019

ECN N°

J.W

1114

NH

F

E

D

C

B

19

1

Pos. Part No.

A

GA2000209

1 GA4600905

2 GA5023135

3 GA5078498

4 GA5077710

5 GA5007231

6 GA5078022

7 GA5077730

8 GA5002783

9 GA5077704

10 GA5077719

11 GA5000999

12 GA5001009

13 GA5000895

14 GA5001029

15 GA4404755

16 GA5000577

17 GA5012461

18 GA5000311

19 GA5003783

14

12

12

13

4

D

5

15

1

16

16

18

11

9

6

8

10

ITEM NO.

1

2

3

10

11

12

13

14

8

9

4

5

6

15

16

1

18 GA5000311

Description


Frame, 600L, Traymount, Pro Reel

600L Cartage Spray tank with sump and lid

Lid, Hinged, Black plastic, 355mm


0. ± 1 ANGULAR ± 0.50°

0.0 ± 0.5

0.00 ± 0.25



4

-


Bush, Reducing, Poly, 2” Male Thread x 1 1/4" Female Thread

Hose barb, Elbow, 90 degree, 1 1/4" male thread x 1 1/4" hose

Hose Clamp, 1 1/4", SS


Hose barb, Elbow, 90 degree, 1" male thread x 3/4" hose

Hose Clamp, 3/4", SS

Washer 16mm Flat ZP HD


Nut M16 Nyloc ZP

Plate, Tank Adjuster, Compact


Nut M12 Nyloc ZP

Set Screw M12 x 35 GR 8.8 ZP


Qty.

1

1

1

2

2

1

1

4

8

8

4

1

2

1

1

16

8

8

4

3

19

MATERIAL :

WEIGHT:

KG

GA5003 83

SURFACE FINISH:

DEBURR AND BREAK

SHARP EDGES

PART NUMBER

GA4600905

GA5023135

GA50 8336

GA50

GA500 231

GA50 8022

GA50

GA50

GA50

GA50005

10

30

GA5002 83

04

19

GA5000999

GA5001009

GA5000895

GA5001029

GA4404 55

GA5012461

H

H

R

H

H

F

L , H

600 C

, B

E

, E

, E

, E

DRAWN BY:

JACK W

10/11/2016

MODEL EDITED BY:

NEALHARVEY

25/11/2019

DRAWING EDITED BY:

NEALHARVEY

25/11/2019

DRAWING CHECKED BY:

, E

, P

H

TITLE:

, 90

H

, 2

, 90

S

DESCRIPTION

, 600L, T

,

C

, 90

, 90

3/4 SS

, 1/2

, 1

, P R

, 355

3/4

, 356040

, 3/4

, C

1 1/4

, 1/2

1/2 , B

B

, 1 1/4

, 1 1/4, SS 30-45/13W

, B

1 1/4

3/4 , B

, B

,

P

W 16 F P HD

B M16 220 GR8.8 P

N M16 N P

W

, T A , C

12

N M12 N

F SS HD

P

S S

, B , I

M12 35 GR 8.8 P

, RHS. 50 50, 0.8 - 2.5

8

16

8

8

4



PH: 03 5342 6399

1

1

TY.

1

2

2

1

1

1

2

8

4

4

1

1



DRAWING NUMBER:

GA4914030

REV

04

SHEET

A3

2


1

C

B

A

31

B

D

F

E

15

16

17

11

12

13

14

8

9

10

6

7

4

5

1

2

3

6


GA5023085

GA5072295

GA5072285

GA5077650

GA5048655

GA5003643

GA5004917

GA5006161

GA5000117

GA5000141

5 4

DESCRIPTION

Honda engine 3/4" shaft

Reduction Gearbox, Ratio 6:1, S160-3/4 GR, Suit Delta 40-50 GR

Pump, Delta 40 GR




Nut M8 Nyloc ZP



Nut M10 Nyloc ZP

GA4400415

GA5004097

Plate, Delta 40 Pump Mount, 200-400L kubota RTV


GA5004437 Washer 6mm Flat SS

GA5075657 Hose barb, Elbow, 90 degree, 13mm hose, including 1/2 fly nut and seal, Brass, Arag

GA5075745

GA5000999

GA5077707

Hose barb, Elbow, 90 degree, Fly nut end x 20mm hose, Udor, 025404

3/4" SS hose clamp

Hose barb, 1/2 male thread x 3/4 hose, Banjo

18

19

20

GA5018309

GA5001741

GA5012273

Valve, Ball, 12mm, 1/2" female, Lever handle, Brass



Traymount 600L - Pump & Drain

-

-

-

-

-

1

-

-

2

1

1

2

Pump/QTY. Drain/QTY.

1

1

1

-

-

-

4

8

4

8

4

1

4

-

-

-

-

-

-

-

1

1

1

2

1

-

1

1

-

-

-

-

F

E

16

17

18

19

20

21

22

6

7

4

5

1

2

3

12

13

14

15

8

9

10

11

6


GA5023085

GA5072295

GA5072285

GA5077650

GA5048655

GA5003643

GA5004917

GA5006161

GA5000117

GA5000141

GA4400415

5 4

DESCRIPTION

Honda engine 3/4" shaft

Reduction Gearbox, Ratio 6:1, S160-3/4 GR, Suit Delta 40-50 GR

Pump, Delta 40 GR




Nut M8 Nyloc ZP



Nut M10 Nyloc ZP

Plate, Delta 40 Pump Mount, 200-400L kubota RTV

GA5004097

GA5004437


Washer 6mm Flat SS

GA5075657 Hose barb, Elbow, 90 degree, 13mm hose, including 1/2 fly nut and seal, Brass, Arag

GA5075745 Hose barb, Elbow, 90 degree, Fly nut end x 20mm hose, Udor, 025404

GA5000999

GA5077707

GA5018309

GA5001741

GA5012273

GA5077132

GA5077137

3/4" SS hose clamp

Hose barb, 1/2 male thread x 3/4 hose, Banjo

Valve, Ball, 12mm, 1/2" female, Lever handle, Brass



Cam lever, 3/4 female coupling x 3/4 female thread, Banjo

Plug, Cam lever, 3/4 male, Banjo

-

-

1

1

2

2

-

-

-

-

-

Pump/QTY. Drain/QTY.

1

1

1

-

-

-

4

1

4

8

8

4

1

4

C

-

-

-

-

-

-

-

-

B

1

1

-

-

-

-

1

2

1

1

1

12

D

3

13

4

14

15

11

REV.

02

03

04

10 9

2

REVISIONS

DESCRIPTION

Changed to suit picklist

Model & Bom updated

Model & BOM update

1

DATE

3/08/2017

8/07/2019 JM

25/11/2019

ECN N°

J.W

1114

F

9 8 3 2

7

6

6

5

E

C

14

15

1

A

6

19

5

18

17

16 4

3

REV.

02

03

04

19

18

17

16

22

21

20

19

2

REVISIONS

DESCRIPTION


Model & Bom updated

Model & BOM update

1

DATE

3/08/2017

8/07/2019 JM

25/11/2019

ECN N°

J.W

1114

NH

F

E

D

C

B

D



MATERIAL

:

SURFACE FINISH:


0. ± 1 ANGULAR ± 0.50°

0.0 ± 0.5

0.00 ± 0.25

WEIGHT:

KG




3

DEBURR AND BREAK

SHARP EDGES

DRAWN BY:

JACK W

10/11/2016

MODEL EDITED BY:

NEALHARVEY

25/11/2019

DRAWING EDITED BY:

NEALHARVEY

25/11/2019

DRAWING CHECKED BY:

TITLE:

2



PH: 03 5342 6399



DRAWING NUMBER:

GA4914030

REV

04

SHEET

A3


1

A

C

12

13

4

11

10 9 9 8 3 2

7

6

6

5

22

21

20

19

B

A

6 5 4



MATERIAL

:


SURFACE FINISH:

0. ± 1 ANGULAR ± 0.50°

0.0 ± 0.5

0.00 ± 0.25

WEIGHT:

KG




3

DEBURR AND BREAK

SHARP EDGES

DRAWN BY:

JACK W

10/11/2016

MODEL EDITED BY:

NEALHARVEY

25/11/2019

DRAWING EDITED BY:

32

NEALHARVEY

25/11/2019

DRAWING CHECKED BY:

TITLE:

2


PH: 03 5342 6399



DRAWING NUMBER:

GA4914030

REV

04

SHEET

A3


1

A

Traymount 600L - Pump & Drain

Pos. Part No.

1 GA5023085

2 GA5072295*

3 GA5072285*

4 GA5077650*

5 GA5048655

6 GA5003643

7 GA5004917

8 GA5006161

9 GA5000117

10 GA5000141

11 GA4400415

12 GA5004097

13 GA5004437

14 GA5075657

15 GA5075745

16 GA5000999

17 GA5077707

18 GA5018309

19 GA5001741

20 GA5012273

21 GA5077132

22 GA5077137

Description

Engine, GX200, 3/4” shaft, Honda

Reduction Gearbox, Ratio 6:1, S160-3/4 GR - Suit GX200

Pump, Delta 40 GR




Nut M8 Nyloc ZP



Nut M10 Nyloc ZP

Plate, Delta 40 Pump Mount, 200-400L Kubota RTV


Washer 6mm Flat SS

Hose barb, Elbow, 90 degree, 13mm hose, including 1/2" fly nut and seal, Brass

Hose barb, Elbow, 90 degree, Fly nut end x 20mm hose

Hose Clamp, 3/4", SS

Hose barb, 1/2" male thread x 3/4" hose

Valve, Ball, 12mm, 1/2” female, Lever handle, Brass



Cam lever, 3/4" female coupling x 3/4" female thread

Plug, Cam lever, 3/4" male


1

1

1

2

1

1

1

1

1

Qty.

4

4

4

8

1

1

1

1

1

2

8

4

2

33

F

E

D

C

6


1

2

3

GA4900546

GA5066080

GA4532190

15

16

17

18

11

12

13

14

8

9

10

6

7

4

5

23

24

25

19

20

21

22

5

DESCRIPTION

Gunjet, AA30, adjustable nozzle, with 1/2" fittings

Hose reel, 30m 3/8" hose, manual rewind


GA5006161

GA5000117

GA5000141

GA5000351

GA5000577

GA5012461

GA4600935

GA5006073

GA4534635

GA5013003

GA5004085

GA5004919

GA5003643

GA5002783

GA5004917

GA2000106

GA5077679

GA5076037

GA5076604



Nut M10 Nyloc ZP



Nut M12 Nyloc ZP

Hose Reel Adaptor, Suits Pro Reel, Traymount


Bracket, hand Gun jet holder support

Pipe linch pin, 8 OD x 60 long




Hose Clamp, 1 1/4, SS (30-45/13W)

Nut M8 Nyloc ZP

Suction Filter, 1-1/2" 50 Mesh, 1-1/2" BSP Male Threads, Geoline

O ring, 30 x 3, G10061

Hose barb, Straight, 1 1/2 fly nut end x 32mm hose, Arag

Fly nut, 1 1/2, Arag

GA5076259 Hose barb, Elbow, 90 degree, 1 1/2 fly nut end x 32 mm hose, Arag

GA5000469

GA5003783



4 filter/QTY. Hose Reel/QTY.

-

-

1

1

1

2

-

3

3

-

3

-

-

-

-

-

-

-

-

-

1

-

-

1

2

1

2

-

2

1

5

1

3

1

1

4

2

1

4

10

5

2

-

1

4

-

-

-

F

19

20 21 17 22

3

REV.

02

03

2

7

REVISIONS

DESCRIPTION


Model & Bom updated

8 8 9

1

8/07/2019 JM

4

DATE

3/08/2017

5 5 6

ECN N°

J.W

1114

NH

F

E

D

11

12

13

7

8

9

10

4

5

2

3

6

14

15

20

21

22

23

16

17

18

19

24

25

6


1 GA4900546

GA5066080

GA4532190

GA5006161

GA5000117

GA5000141

3

5

DESCRIPTION

Gunjet, AA30, adjustable nozzle, with 1/2" fittings

Hose reel, 30m 3/8" hose, manual rewind



12

Nut M10 Nyloc ZP

GA5000351

GA5000577

GA5012461

GA4600935

GA5006073

GA4534635

GA5013003



Nut M12 Nyloc ZP




Pipe linch pin, 8 OD x 60 long

13


GA5004085

1

GA5003643

24

GA2000106

GA5077679

GA5076037

25

O ring, 30 x 3, G10061

16

11 5

Hose barb, Straight, 1 1/2 fly nut end x 32mm hose, Arag

GA5076604 Fly nut, 1 1/2, Arag

GA5076259 Hose barb, Elbow, 90 degree, 1 1/2 fly nut end x 32 mm hose, Arag

GA5000469

GA5003783

14

15

16


Hose Clamp, 1 1/4, SS (30-45/13W)

Nut M8 Nyloc ZP

14

16

10

2

4 filter/QTY. Hose Reel/QTY.

1

5

-

-

-

-

-

-

-

3

3

-

-

-

-

-

2

1

2

1

-

-

-

1

3

2

6

1

1

1

2

1

2

4

1

1

4

10

5

3

1

-

-

-

-

1

4

2

-

5

-

E

D

C

B

18

B

A

6

16

15

14

5

20 23 22 17

4

20 21 17 22

C



MATERIAL

:

SURFACE FINISH:


0. ± 1 ANGULAR ± 0.50°

0.0 ± 0.5

0.00 ± 0.25

WEIGHT:

KG




3

DEBURR AND BREAK

SHARP EDGES

DRAWN BY:

JACK W

10/11/2016

19

25/11/2019

DRAWING EDITED BY:

NEALHARVEY

25/11/2019

DRAWING CHECKED BY:

TITLE:

2



PH: 03 5342 6399



DRAWING NUMBER:

GA4914030

REV

04

SHEET

A3


1

A

B

16

15

14

A

6 5

34

20 23 22

1

24

3

REV.

02

03

04

3

12

13

14

15

16

25

14

16

16

18

2

REVISIONS

DESCRIPTION


Model & Bom updated

Model & BOM update

7 8 8 9

10

1

DATE

3/08/2017

8/07/2019 JM

25/11/2019

ECN N°

J.W

1114

NH

F

4 5 5 6

2

11 5 5 6

E

D

C

B



MATERIAL

:

17 UNLESS OTHERWISE SPECIFIED

0. ± 1 ANGULAR ± 0.50°


SURFACE FINISH:

WEIGHT:

KG

4




3

DEBURR AND BREAK

SHARP EDGES

DRAWN BY:

JACK W

10/11/2016

MODEL EDITED BY:

NEALHARVEY

25/11/2019

DRAWING EDITED BY:

NEALHARVEY

25/11/2019

DRAWING CHECKED BY:

TITLE:

2



PH: 03 5342 6399



DRAWING NUMBER:

GA4914030

REV

04

SHEET

A3


1

A

Traymount 600L - Hose Reel & Suction Filter

Pos. Part No.

1 GA4900546*

2 GA5066080

3 GA4532190

4 GA5006161

5 GA5000117

6 GA5000141

7 GA5000351

8 GA5000577

9 GA5012461

10 GA4600935

11 GA5006073

12 GA4534635

13 GA5013003

14 GA5004085

15 GA5004919

16 GA5003643

17 GA5002783

18 GA5004917

19 GA2000106*

20 GA5077679

21 GA5076037

22 GA5076604

23 GA5076259

24 GA5000469

25 GA5003783


Description

Gunjet, AA30, 5500-X18 adjustable nozzle, 1/2" Hose Barb

Hose reel, 30m 3/8” hose, manual rewind




Nut M10 Nyloc ZP



Nut M12 Nyloc ZP




Pipe linch pin, 8 OD x 60 mm long




Hose Clamp, 1 1/4", SS

Nut M8 Nyloc ZP

Suction Filter, 1-1/2” 50 Mesh, 1-1/2” BSP Male Threads

O ring, 30 x 3 mm

Hose barb, Straight, 1 1/2" fly nut end x 32mm hose

Fly nut, 1 1/2"

Hose barb, Elbow, 90 degree, 1 1/2 fly nut end x 32 mm hose



Qty.

4

8

1

6

1

1

2

1

10

5

2

4

1

4

1

1

1

1

1

2

4

1

2

2

2

35

Spray Gun - GunJet AA30L

The gunjet trigger needs to be locked via the trigger lock when not in use to prevent the gunjet from spraying inadvertently.

No. AAB30L-¼, GunJet Spray Gun (BSPT

Threads)

AB30L-Kit - Spare Parts Kit (Includes all items marked with * and item 7)

Pos.

11

12

13

14

7A

8*

9

10

5

5A

6*

7

3

4*

1

2

19

20

21

22

23

15

16

17

18*

Part No.

CP17103-11/16-302SS

GA5077414

GA5077610

GA5077590

GA5077441

CPB22136

GA5077442

GA5077376

GA5077377

GA5077421

GA5077420

GA5077588

GA5077589

CP7622-302SS

GA5077407

GA5077427

CP17703-NY

GA5077419

GA5077423

GA5077443

GA5077424

GA5077426

GA5077425

GA5077417

GA5077416

Description

Screw, Type 302 Stainless Steel (7 Req’d)

Right and Left hand Housing Set, Nylon (Black)

Cap, Steel, Nickel Plated

Valve Seat, Brass and Teflon

Inlet Body, Brass (For Model 30L-¼)

Inlet Body, Brass (For Model B30L-¼)

Stem Sub-Assembly, Brass and Type 302 SS

Cup Packing, Buna-N

Cup Packing, Viton

Gasket, Brass

Packing Screw, Brass

Stem Nut, SS

Trigger Stop Spring, Type 302 SS

#6 Burr, Type 302 SS

Roll Pin, Type 420 SS

Roll Pin, Type 420 SS

Trigger, Nylon (Yellow)

Trigger Guide, Brass

Spring Guide, Brass

Spring, Type 302 SS

Spring Retainer, Brass

Washer, Type 18-8 SS

Screw, Type 18-8 SS

Trigger Lock, Nylon (Yellow)

Lock Spring Ring, Celcon

36

Spray Gun - Nozzle

The adjustable brass ConeJet nozzle rotates through a half turn to provide spray selection from wide angle, finely atomized cone spray to a straight stream spray.

NOTE : Tip settings “A” and “B” represent two extreme points of rotation in tip adjustment.

Adjustable

ConeJet Tip

No.

GA8100370

Standard

GA8100377

GA8100371

Performance

Capacity—l/min

Spray angle º

Max throw m

Capacity—l/min

Spray angle º

Max throw m

Capacity—l/min

Spray angle º

Max throw m

1.5

Liquid Pressure (bar)

2 3 4

A B A B A B A B

0.79

2.61

0.98 3.18 1.14 3.67 1.40 4.54

71 75 77 78 -

1.2

11.6

1.2

12.8

1.2

13.3

1.2

13.0

0.98

3.14

1.21 3.79 1.40 4.54 1.70 5.30

71 75 78 79 -

1.2

11.7

1.40 13.0

1.5

13.6

1.5

13.2

1.17

3.71

1.40 4.54 1.63 5.30 2.01 6.43

72 76 78 79 -

1.4

11.6

1.5

13.1

1.5

13.7

1.7

13.3

37

Pump - Delta 40

GA5076553

GA2000097

GA5076507

GA5076068

GA5076511

GA5075660

GA5075757

GA5075993

GA5072285 Pump, Delta 40 GR

GA5076068

GA5075802

GA5078313

GA5076361

GA5076441

GA5075602

GA5075755

GA5075624

GA5075789

GA5075684

GA5076074

GA5078307

GA5075730

GA5076517

GA5076065

GA5076361

GA5078317

GA5075761

GA5076553

GA5076450

GA5076456

GA5076386

GA5076561

GA5076441

GA5075993

GA2000097

GA5075660

GA5075757

Part No.

Description

GA5072285 Pump, Delta 40 GR

GA5023870-SK Diaphragm kit

GA5077781 Pump Repair kit, Delta 40, includes diaphragms seals & valves

GA2000097 Diaphragm, Desmopan


38

Pump - Delta 40

Part No.

Description

GA5075602 Retainer ring

GA5075624 Bushing D25X32X20

GA5075660 Bolt, Suit pump diaphragm

GA5075684 Hose barb, Elbow, 90 degree, Fly nut end x 32mm hose

GA5075730 Ball bearing D35X72X17

GA5075755 Bearing disc

GA5075757 Diaphragm disc

GA5075761 Rod spacer

GA5075789 Plastic nut M42X2

GA5075802 Air valve assembly

GA5075993 Diaphragm, Pump accumulator

GA5076065 O-ring D23,52X1,78

GA5076068 O ring, 6.00 x 3 mm

GA5076074 O ring, 28.00 x 3.00 mm

GA5076361 Base plate

GA5076386 Aluminium plunger

GA5076441 Washer D10,5X18X2

GA5076450 Pin D15X48

GA5076456 Snap ring

GA5076507 Oil plug

GA5076511 Plug G3/8+Gasket

GA5076517 Plug G1/2

GA5076553 Hex screw M8X35 UNI5737

GA5076561 Bolt, M10 x 70

GA5078307 Snap ring

GA5078313 Oil plug, 3/8", Brass

GA5078317 Hex screw M10X25 UNI5739

39

Gearbox

GA5075785

GA5076564

GA5076557

GA5075741

GA5076097

GA5076572

GA5075799

GA5078313

GA5075621

Part No.

Description

GA5072295 Reduction Gearbox, Ratio 6:1, S160-3/4 GR - Suit GX200

GA5076453 Gear body

GA5075786 Gasket, Coupler

GA5075626 Bushing

GA5076516 Oil plug + Gasket

GA5076571 Hex screw, Coupler

GA5075621 Gear shaft, motor to gear box, 3/4"

GA5075799 Gasket, Oil plug

GA5078313 Oil plug, 3/8”, Brass

GA5075785 Gasket, Pump side

GA5076564 Allen screw, M10 x 25

GA5076557 Bolt, M8 x 50

GA5075741 Coupler

GA5076097 O ring, 42.52 x 2.62 mm

GA5076572 Hex screw, Gear shaft

40

GA5076453

GA5075786

GA5075626

GA5076516

GA5076571

A

3 4

REV

5

REVISIONS

DESCRIPTION

6

DATE / INITIAL ECN

A

B

1

2

B

C

D

3

4

5

ITEM NO.

1

PART NUMBER

C00002018

2

3

4

GA50242 5

GA5024285

GA5024295

B

O-

, S

DESCRIPTION

, 1 1/2 , G , C00002018

, 5.34 94.62

GA2000106, G

, S , 1 1/2 ,

, G00001062

N , S , 1 1/2 , G , G00101002

G

F S

F

, 50 M

GA2000106, O-

. G

, D 9 16

GA5024290

, C00100012

, S

5 C00201009 B , S , 1 1/2 , G , C00201009

6 K00100001 D , S , 1 1/2 , G , K00100001

1

1

1

1

1

1

TY.

C

D

E E

F

Pos. Part No.

GA2000106

1 C00002018

2 GA5024275

3 GA5024285

4

GA5024295

GA5024290

5 C00201009

6 K00100001

6



MATERIAL

:


0. ± 1 ANGULAR ± 0.50°

0.0 ± 0.5

0.00 ± 0.25

SURFACE FINISH:

Description



Suction Filter, 1 1/2” 50 Mesh, 1 1/2” BSP Male Threads,

Geoline

2 3

Body, Suction filter, 1 1/2", Geoline, C00002018

O-ring, 5.34 x 94.62 mm, Suction filter, 1 1/2”, suits

GA2000106

Nut, Suction filter, 1 1/2”, Geoline

Filter Screen, 50 Mesh, Dia 79 x 167 mm length, Suit Geoline

Filter GA2000106, O-rings GA5024290 are not included.

O-ring, Suit filter mesh

Bowl, Suction filter, 1 1/2”, Geoline, C00201009

Drain plug, Suction filter, 1 1/2”, Geoline, K00100001

Qty.

-

1

1

1

1

2

1

1

4

DEBURR AND BREAK

SHARP EDGES

DRAWN BY:

NAME

MODEL EDITED BY:

NEALHARVEY

1/08/2016

/10/2019

DRAWING EDITED BY:

NEALHARVEY

/10/2019

DRAWING CHECKED BY:

TITLE:

5



PH: 03 5342 6399

TITLE

DRAWING NUMBER:

GA2000106


REV

SHEET 1 OF 1

6

SHEET

A3

F

41

GA5077088

Pressure Control Unit

GA5076067

GA5075791

GA5075681

GA5075804

GA5076440

GA5076558

GA5075803

GA5078264

GA5075999

GA5075787

GA5076060

GA5076513

GA5076382

GA5076573

GA5076558

GA5076440

GA5075697

GA5077105

GA5075695

GA5075995

GA5076546

GA5076439

GA5075983

GA5075978

GA5077105

GA5075986

GA5076074

GA5075696

GA5076067

GA5076506

GA5075792

GA5077184

GA5076377

GA5076446

GA5077779

GA5075995

GA5076060

GA5076067

GA5076074

GA5076382

GA5076446

GA5076573

GA5010731

GA5075995

GA5076060

GA5076067

GA5076074

GA5076446

GA5077184

Part No.

Description

GA5077650 Pressure control unit, valve, DS3, 3 section, 30 Bar, Udor

GA5077088 Pressure control valve, DS3/20

GA5077779 Repair kit, DS2 DS3 controller, KIT552

GA5077780 Repair kit, DS2 DS3 controller, KIT554


42

Pressure Control Unit

Part No.

Description

GA5075681 Hose Barb D20

GA5075695 Regulator Valve Body

GA5075696 Control Body

GA5075697 Cylinder

GA5075787 Nut, 1/2”, Brass with tabs

GA5075791 Fly nut, M30

GA5075792 Nut, Plastic, 3/4"

GA5075803 Hose Barb D10+Gasket

GA5075804 Ball Valve Right

GA5075978 Press. Spring

GA5075983 Spring, Compression

GA5075986 Regulator Handle

GA5075995 Diaphragm, Diameter 36 mm, Control unit flow control

GA5075999 Pressure Gauge, 20 Bar

GA5076060 O ring, 20.63 x 2.62 mm

GA5076067 O ring, 17.13 x 2.62 mm

GA5076377 Elbow

GA5076382 Poppet

GA5076439 Washer, 8.5 ID x 24 OD x 2 mm

GA5076440 Washer D6,4X12X1,6

GA5076446 Valve seat

GA5076506 Plug

GA5076513 Plug G3/8

GA5076546 Adjuster knob, Green

GA5076558 Hex Screw M6X60 UNI5737

GA5076573 Allen Screw M6X30 UNI5931

GA5077105 Regulator Cylinder Kit

GA5077184 Regulator Valve Repair Kit

GA5078264 Hose Barb D13+Gasket

43

1-3 Morang Crescent, Mitchell Park Vic 3355

P: 03 5342 6399 F: 03 5342 6308 [email protected]

goldacres.com.au

44

Goldacres Traymount 400L Operator's & Parts Manual

1

Contents

2

Introduction

3

Safety

General

The Operator

Safety Precautions

WARNINGS

CAUTIONS

4

NOTES

Safe Chemical Use

Personal Protective Equipment (PPE)

Airborne particles

Fluids under pressure

5

Cuts, Stabs & Punctures

Mount Vehicle Safety

6

Safety Decals

Traymount 200 Decal Kit

Traymount 300 Decal Kit

7

Traymount 400 Decal Kit

Traymount 600 Decal Kit

GA8700438 600L Traymount Pro-Reel site tube

8

Warranty

How to make a warranty claim

Warranty Duration

Warranty Inclusions

Warranty Exclusions

9

Conditions of Warranty Coverage

Goldacres Warranty Statement

Goldacres warranty cover excludes:

10

General Information &

Specifications

Know Your Sprayer

Chassis

Tank

Filtration

Pump

Machine limitations

Paint Colours

Identification

11

Dimensions

12

13

Model Net Weight

Key Features

Number Description

Number Description

14

Sprayer Transport

Vehicle Mounting

First Time Start Up

15

Honda GX200 & Delta 40 Pump

12

13

16

14

15

10

9

6

5

3

4

2

Key Features

Number Description

16

Number Description