Quantum Rehab Network Adapter Dynamic DX Basic Operation Instructions

PDF

Document

All manuals and user guides at all-guides.com

Dynamic DX

Scanner Control

TM all-guides.com

Basic Operation Instructions

All manuals and user guides at all-guides.com

Basic Operation Instructions

IMPORTANT NOTICE

DX Scanner

This manual describes basic operation for the Dynamic DX Scanner Control only and must be read in conjunction with the owners manual supplied with your power chair. Please read both manuals in their entirety before operating the Dynamic DX Scanner Control or your power chair.

This manual is intended as a supplement to the in-service training provided by your authorized provider. If you have any questions or problems regarding the Dynamic DX Scanner Control, please contact your authorized provider.

Pride Mobility Products Corporation

DX Scanner

All manuals and user guides at all-guides.com

Basic Operation Instructions

INTRODUCTION ................................................................................ 4

Dynamic DX Scanner Control ................................................................... 4

SELECT MODE ................................................................................... 6

DRIVE MODE ....................................................................................... 6

SEAT MODE ......................................................................................... 7

ENVIRONMENTAL MODE .............................................................. 8

SCANNING SPEED ADJUSTMENT ........................................... 8

All manuals and user guides at all-guides.com

Basic Operation Instructions DX Scanner

INTRODUCTION

Welcome to Quantum Rehab, a division of Pride Mobility Products

Corporation (Pride). Quantum Rehab is dedicated to the customization of power chairs for users with advanced rehabilitation and mobility issues.

Quantum Rehab also expands possibilities for enhanced healthcare attendant control over power chair functions to provide a secondary level of support for our customers where necessary.

Dynamic DX Scanner Control

The Dynamic DX Scanner Control allows the power chair user to control drive modes, actuators, and secondary remote controls.

This manual is designed to explain basic operation of the following functions available with the Scanner:

1. Select Mode

- Allows the user to choose one of three different modesDrive, Seat, or

Environmental.

2. Drive Mode

- Allows the user to control the speed and direction of the power chair.

3. Seat Mode

- Allows the user to select and adjust one of four seat actuators.

4. Environmental Mode

- Allows the user to select and control the attached environmental control or communication device.

5. Scanning Speed Adjustment

- The user can adjust the speed with which the Scanner cycles through the available options.

Figure 1 provides information on the Scanner Control components and connections. Use this diagram to familiarize yourself with the function and location of each component before using the Dynamic DX Scanner Control.

DX Scanner

Module Status LED

Indicates the status of the

Scanner; flashes when there is a fault within the Scanner

(not the power chair).

All manuals and user guides at all-guides.com

Basic Operation Instructions

Drive Mode LED

Indicates if the Drive

Mode is powered on or off.

Seating Status LED

Indicates if actuator control is powered on or off.

Seating Mode LED

Indicates if Seating Mode is powered on or off.

Environmental Mode LED

Indicates if Environmental Mode is powered on or off.

Direction LEDs

A set of 8 LEDs which indicate drive direction or function.

BACK OF MODULE

Select Switch Socket

Used to connect a switch that can control all functions of the Scanner.

DXBUS Socket

Used as an interface to connect the DX Scanner to other DX compatible controls.

Environmental Socket

Used to connect an environmental control or communication device to the Scanner.

Figure 1. Scanner Control Components and Connections

All manuals and user guides at all-guides.com

Basic Operation Instructions DX Scanner

SELECT MODE

1. Press the On/Off Button on the DX compatible Master Remote used on your power chair. The Module Status LED on the Scanner will light up, indicating that it is in Standby Mode and ready for use.

2. Press the Select Switch once to activate the Scanner. All three Mode

LEDs will light up.

3. After power up, the Scanner will begin running through the three modes

Drive, Seat, and Environmental. Each Mode LED will light up in sequence. To choose a mode, you must wait for its LED to light up, then press the Select Switch.

NOTE: The Scanner will run through each Mode LED five (5) times before returning to Standby Mode.

DRIVE MODE

1. Press the Select Switch when the Drive Mode LED is lit. Once selected, the Scanner will cycle through the available drive directions.

2. To move in any direction, wait until the desired Directional LED is lit, then press and hold down the Select Switch to move your power chair in that direction. The

Scanner will automatically return to the Forward Direction LED after any power chair movement.

See figure 2.

all-guides.com

Figure 2. Directional LEDs

NOTE: If the Select Switch is not pressed within three scanning cycles of the Drive Mode, the Scanner will exit that mode.

DX Scanner

All manuals and user guides at all-guides.com

Basic Operation Instructions 7

SEAT MODE

1. Press the Select Switch when the Seat Mode LED is lit. Once selected, the Scanner will cycle clockwise around the seating commands (Directional

LEDs).

2. There are four Seat Positioning

Actuators represented by two each of the Directional LEDs.

For example, Actuator 1 is represented by the Forward and the Forward Right Directional

LEDs. See figure 3. To extend

Actuator 1, wait until the

Forward LED is lit, then press

Figure 3. Actuator Selections and hold down the Select Switch. To retract Actuator 1, wait until the

Forward Right LED is lit, then press and hold down the Select Switch.

3. To operate a fifth actuator (if available), use the Environmental Mode

LED (see figure 1). Wait until the Environmental Mode LED is lit, then press and hold down the Select Switch to extend the actuator. To retract the actuator, press and hold down the Select Switch again. If you have any questions regarding the use of the fifth actuator, please contact your authorized provider.

NOTE: If the Select Switch is not pressed within three scanning cycles of the Seat Mode, the Scanner will exit that mode.

All manuals and user guides at all-guides.com

Basic Operation Instructions DX Scanner

ENVIRONMENTAL MODE

1. Press the Select Switch when the Environmental Mode LED is lit. Once selected, the Scanner will cycle clockwise from the top (forward) LED.

See figure 2.

2. The first four LEDs are momentary selections, and the last four LEDs are latching selections. Momentary selections will allow the Scanner to continue its cycle immediately after the switch is released. Latching selections will not allow the Scanner to continue its cycle until the Select

Switch has been pressed for a period of five seconds. The Scanner will remain in the selected mode until the Select Switch is pressed for a period of five seconds.

NOTE: If the Select Switch is not pressed within three scanning cycles of the Environmental Mode, the Scanner will exit that mode.

SCANNING SPEED ADJUSTMENT

The Scanning Speed is indicated by the amount of time any one LED is lit before the Scanner moves on to the next LED.

1. Press the Select Switch to power on the Scanner. Wait for the Mode

LEDs to light up.

2. When all three LEDs are lit, press the Select Switch and hold it down.

The Scanning Speed will reset itself to the amount of time you hold down the Select Switch.

NOTE: The Scanning Speed will need to be adjusted every time the

Scanner is turned on. It cannot be permanently set.

DX Scanner

All manuals and user guides at all-guides.com

Basic Operation Instructions

NOTES

All manuals and user guides at all-guides.com

Basic Operation Instructions

NOTES

DX Scanner

All manuals and user guides at all-guides.com

Basic Operation Instructions

NOTES

11 all-guides.com

All manuals and user guides at all-guides.com

Basic Operation Instructions DX Scanner

Exeter, PA

Quantum Hotline: 1-866-800-2002

Visit the Rehab Zone at: www.quantumrehab.com

INFMANU1747/A/JULY 2001

Hello! I am an AI chatbot specifically trained to assist you with the Quantum Rehab Network Adapter Dynamic DX Operating instructions. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!