Date:
Model Number:
Classé Audio Inc.
Subject:
August 22, 2007
CAP-80 / CAP-101
Service manual
Classé Audio, Inc. 5070 François Cusson Lachine, Québec Canada H8T1B3, www.classeaudio.com
PRO-SVR_LEGACY Page 1 of 14
Table of Contents
Introduction 3
Important Notes on Servicing 3
Ordering Replacement Parts 3
Block Diagrams 4
Start up Procedure 5
Protection Modes and Indicators 6
Troubleshooting Guide 7
Output Transistors Testing and Replacement 8
Calibrations and Adjustments 9
Parts List 10
Updates 11
Fuses 12
Voltage Change 13
IR Interface Information 14
Schematics 15
PRO-SVR_LEGACY Page 2 of 14
Introduction
Please read this manual carefully before commencing servicing!
Only qualified and authorized personnel should attempt to service this product.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions.
Classé has a global product support network. For product assistance or to order replacement parts please contact your nearest service center always quoting the unit serial number.
North America
Phone: (978) 664-2870 E-mail: [email protected]
Europe
Phone: 44 (0) 1903 221 700 E-mail: [email protected]
Asia
Phone: (852) 2790 8903 E-mail: [email protected]
Rest of the World
Phone: (514) 636-6384 E-mail: [email protected]
Important Notes on Servicing
1.
ALWAYS observe ESD precautions when handling electronic modules or PCBAs.
2.
NEVER exchange boards with a different revision number, unless authorized by Classé.
3.
ALWAYS use Classé original replacement parts. The use of generic parts may void the warranty of the unit.
Ordering Replacement Parts
There may be a delay in processing incomplete requests. Please be sure to include all required information.
Remember to quote the serial number of the unit on all replacement part orders and the Classé order number when returning defective parts for credit.
PRO-SVR_LEGACY Page 3 of 14
Block diagrams
PRO-SVR_LEGACY Page 4 of 14
Start Up Procedure
When receiving a unit, an assiduous visual inspection must be performed. Do not connect the unit without analysing the symptoms reported by the customer and the results of the inspection.
Using the troubleshooting guide, find the problem and proceed to the repair. Once this step is done, follow these steps, known as the start-up procedure, to ensure that everything in the unit is in working condition.
1. Proceed with a post repair visual inspection. Take the time to check if every wire is reconnected properly, every screw is bolted on, no soldering and/or metal residues lying in the unit, every fuse has been replaced, etc.
2. Turn the bias trimpots, counter clockwise until a click is heard.
3. Since there is no soft-start sequence of the CAP-80 / CAP-101, it is impossible to use a bypass to perform a slow start up.
4. Connect Main supply, and turn on the unit.
5. If one or more supply are not within specifications, return to the troubleshooting guide.
6. If every supply is within specifications, report to calibration and adjusments to adjust bias and DC offset. Note that bias can be adjusted to 14mV, and the following tests can be performed before the unit is send to the burn-in bench for a 24 hours warm-up.
7. Connect the unit to a load, and to a source using single ended inputs.
8. Perform a test with a 200Hz, a 2kHz and a 20kHz tone, both sinus wave and square wave. Check the output with a oscilloscope, on 4 ohms and 8 ohms loads. Take special cares about oscillation and phase correlation between channels.
9. Connect the unit to a small speaker, and short the input. Check for any noise.
10. Put the unit on a burn-in bench, and let it sit for 24 hours, then readjust bias. Let the unit on the burnin bench for another 72 hours.
11. Redo steps 7 to 11 before shipping to the customer.
PRO-SVR_LEGACY Page 5 of 14
Protection Modes and Indicators
The front LED display shows the status of the amplifier. When starting up normally, the CAP80 / CAP101 will show a countdown from 20 to 0. However, there is no protection on the CAP80 / CAP101. The CAP80 /
CAP101 is equipped with four rail protection fuses. In the event that one or more of these fuses would blow, the technician will first need to identify and cure the cause of failure (please report to troubleshooting guide).
When the cause has been identified, disconnect the unit from the system including the AC power. Remove the top cover and look for damaged or burned components. If no other components than the fuses appear to be damaged, the technician can then replace the broken fuses with the same value and rating (please report to fuses section). The rail fuses are located on the main board. When replacing fuses, please make sure that the fuse holder are holding the fuses very tightly. A loose fuse holder can translate into distortion on top of the signal.
PRO-SVR_LEGACY Page 6 of 14
Troubleshooting Guide
Unit won’t turn on
Smoked and/or burned components
Blown fuses
No output
Unit turn into protection
Excessive buzz and/or hum
Intermittent signal
Check connections;
Check fuses;
Check soft-start circuit;
Check relays;
Check power supply circuits (positive rail, negative rail, Mosfet supply).
Check for short between components and ground;
Check output transistors;
Check output relays;
Check power supply circuits (positive rail, negative rail, Mosfet supply).
Check for short between fuse and ground;
Check power supply circuits (positive rail, negative rail, Mosfet supply).
Check connexions;
Check output relays;
Check power supply circuits (positive rail, negative rail, Mosfet supply);
Check output transistors.
Check for smoked and/or burned components;
Check power supply circuits (positive rail, negative rail, Mosfet supply);
Check source and load;
Check protection circuit;
Check sensor wires between sensor PCB and control PCB;
Check outputs transistors and Mosfet drivers.
Check electrical lines;
Check for a ground loop in the system.
Check capacitors on main board;
Check 4.7
ƻ resistor.
Check connections;
Replace shield wires.
PRO-SVR_LEGACY Page 7 of 14
Output Transistors Testing and Replacement
PLEASE NOTE THAT THESE TESTS ARE ONLY EFFECTIVE ON BIPOLAR TRANSISTORS.
DO NOT PERFORM THESE TESTS ON MOSFET DEVICES, AS THEY ARE LIKELY TO
BECOME SHORT DURING THE TEST.
You should check all pin combinaisons, as there is a chance that only one side of the transistor is short. When replacing outputs transistors, the technician should first disconnect both outputs and main board to check if the blown outputs were caused by a faulty component on the amplifier’s base. Blown output transistors should be replaced by kits, not individually. These kits contains matched transistors for both rails of one channel.
When replacing blown output transistors, you must also replace positive and negative Mosfet drivers and bias transistor. Carefully inspect 4.7
ƻ resistor and 10 ƻ soft start resistor, and replace if necessary. Replace any burnt component or board.
Pins : 1 Base
You should have these results, if the transistor is good.
2SC3263 (NPN)
Positive lead Negative lead Result
C B Infinite
C E Infinite
E B Infinite
E C Infinite
2SA1294 (PNP)
Positive lead Negative lead Result
B C Infinite
B E Infinite
C E Infinite
E C Infinite
PRO-SVR_LEGACY Page 8 of 14
Calibrations and Adjustments
Bias adjustment:
Note: Bias adjustment should be made without any load connected to the amplifier’s output, and no signal connected to the amplifier’s input.
1. Since it is impossible to connect a multimeter to both emitter’s resistors in order to measure and adjust bias without disassembling the heatsink from the chassis, we provided a test point to ease the bias procedure. It is located near the bias trimpot.
2. Connect the positive probe of a millivoltmeter to the test point and the negative probe to the positive speaker post of the channel to be adjusted.
3. Turn trimpots counterclockwise until it reaches 0 ƻ . A click should be heard.
4. Turn on amplifier, and let it warm up for 15 minutes on idle.
5. Adjust trimpot to get a 14mV reading.
6. Let the amplifier warm up for a 24 hours period with signal and load.
7. Remove signal and load, and reconnect the multimeter.
8. Readjust to 20mV.
DC offset:
Note: DC offset adjustment should be made without any load connected to the amplifier’s output, and no signal connected to the amplifier’s input.
On these units, DC offset can’t be adjusted. Measure DC offset using a voltmeter connected to the output posts, scale setted to mV. DC offset should be less than 10mV.
PRO-SVR_LEGACY Page 9 of 14
Parts List
This is not a detailed part list. It is a list of major chassis parts and PCBs. If you need to order a specific part, please contact Classe Audio with the part location, PCB number, and model and serial number of the unit.
If you need a complete PCB, please replace the (x) in the Classe part number with the revision number printed on the board.
Parts
B151X
B152X
B153X
B154X
Complete PCB, input
Description
Complete PCB, supply
Complete PCB, display
Complete PCB, main
Classe part number
B151XR(x)
B152XR(x)
B153XR(x)
B154XR(x)
PRO-SVR_LEGACY Page 10 of 14
Updates
1. On board B154X, replace R122, R126, R222 and R226 with Classe part number RN55D7680.
2. On board B154X, replace RV101 and RV201 with Classe part number 3299W-1-202.
3. On board B154X, replace R134 and R234 with Classe part number A211-1004.
4. On board B154X, replace R128, R129, R228 and R229 with Classe part number A211-1001.
5. Replace shield wires with newer type.
PRO-SVR_LEGACY Page 11 of 14
Fuses
EXTRA PRECAUTIONS SHOULD BE TAKEN WHEN REPAIRING, MODIFYING, OR
TROUBLESHOOTING IN THE POWER SUPPLY AREA. UNIT MUST BE DISCONNECT
FROM MAIN SOURCE AND CAPACITORS MUST BE DISCHARGED USING A 100W
INCANDESCENT BULB.
WHEN REPLACING FUSES, PLEASE MAKE SURE THAT THE FUSE HOLDERS ARE
HOLDING THE FUSES VERY TIGHTLY. A LOOSE FUSE HOLDER CAN TRANSLATE INTO
DISTORTION ON TOP OF THE SIGNAL.
Main fuses:
For 100 – 120v units: 4A slo-blo, Classe part number GDC-4A
For 220 – 240v units: 3.15A slo-blo, Classe part number GDC-3.15A
The main fuse is located at the back of the unit, on the rear panel.
Rail fuses: 4A, Classe part number GDB-4A
The rail fuses are located on the main board (B154X).
Control board fuse: 0.75A, Classe part number 225.750
The control board fuse is located on top of the supply board (B152X)
Mosfet fuses: 0.50A, Classe part number 225.500
The Mosfet fuses are centered on the main board (B154X)
PRO-SVR_LEGACY Page 12 of 14
Voltage Change
EXTRA PRECAUTIONS SHOULD BE TAKEN WHEN REPAIRING, MODIFYING, OR
TROUBLESHOOTING IN THE POWER SUPPLY AREA. UNIT MUST BE DISCONNECT
FROM MAIN SOURCE AND CAPACITORS MUST BE DISCHARGED USING A 100W
INCANDESCENT BULB.
1. Set the primary wires of the main transformer as described below.
2. Replace the varistor, according to new line voltage, following Classe’s recommendations. If varistor is not available, remove old varistor and leave it empty.
3. Set the jumpers accordingly on the auxiliary transformer located at the back of the unit on the top main board on the left-hand side of the auxiliary transformer (see tables below)
Primary wires, main transformer
Mains 1 2 3 4 5 6 7 8
100VAC White Orange
Gray Yellow Blue Blue
Black
Blue
140
120VAC White Orange
220VAC White -
240VAC White -
Blue
Black
Blue Gray Yellow Blue
-
Yellow Blue Blue
Black
Blue
-
Yellow Blue Gray
Black
Blue
140
250
250
Mains
Connector positions
1 2 3 4
5 6 7 8
Position 1
Jumpers, auxiliary transformer
Position 2 Position 3 Position 4 Position 5
PRO-SVR_LEGACY Page 13 of 14
IR Interface Information
Press and hold: AMP +
AMP +
AMP +
AMP +
AMP +
AMP +
LINE 1 =
LINE 2 =
LINE 3 =
BAL 1 =
BAL 2 =
BAL 3 =
Turns on Amplifier # 1
Turns on Amplifier # 2
Turns on Amplifier # 3
Turns on Amplifier # 4
Turns on Amplifier # 5
Turns on Amplifier # 6
J3 J2 J1 J0 ADDRESS
X X X X 0
X X X Out 1
X X Out X 2
X X Out 3
X Out X X 4
X Out X Out 5
X Out Out X 0
X Out Ot Out
Out X X X
0
0
Out X X Out 1
Out X Out X 2
Out X Out Out 3
Out Out X X 4
Out Out X Out
Out Out Out X
Out Out Out Out
5
0
0
RC Button Auto ON Note
Amp1 No QC
Amp2 No
Amp3 No
Amp4 No
Amp5 No
Amp6
Amp1
Amp1
DC
DC
DC
DC
DC
DC
DC
DC
No
No
Yes
No
No
No
No
No
No
No
Yes
On with AC
On with AC
PRO-SVR_LEGACY Page 14 of 14
B154XR08.sch-1 - Mon Aug 20 08:51:40 2007
