Advertisement
Advertisement
Digital DVD Home Theatre
Operator
5
’ manual
DVD HiFi System
QX-3700DV
Operator ’ manual (GB)1~34
Contents
Features ............................................................................................................................ 2
Safety Information .............................................................................................................. 2
Introduction ........................................................................................................................ 4
About DVD................................................................................................................................ 4
About MP3 ................................................................................................................................ 4
About the player........................................................................................................................ 6
Front panel ............................................................................................................................ 6
Rear panel ............................................................................................................................. 6
Remote control....................................................................................................................... 7
Loading and changing the batteries....................................................................................... 7
System connection ............................................................................................................ 8
Connecting to TV set (Video connection) .................................................................................. 8
Connecting to Speakers............................................................................................................ 9
Connecting the Antenna............................................................................................................ 9
Connecting to External Amplifier ............................................................................................... 10
Connecting a Headphone ......................................................................................................... 10
Setting up the player ..........................................................................................................11
Video port setup........................................................................................................................ 11
TV System ................................................................................................................................ 11
Set up the Timer ........................................................................................................................ 12
Getting started ...................................................................................................................13
Selecting a function DVD/TUNER ............................................................................................. 13
Sound Adjustment ..................................................................................................................... 14
DVD Mode ................................................................................................................................ 15
Problem disc messages ............................................................................................................ 15
Tuner Mode ............................................................................................................................... 16
Screen saver ............................................................................................................................ 18
Power management (In DVD mode only) .................................................................................. 18
Function buttons ................................................................................................................ 18
On Screen Display ............................................................................................................. 25
Setup Menu ....................................................................................................................... 28
System...................................................................................................................................... 28
Video ........................................................................................................................................ 28
Audio (digital audio) .................................................................................................................. 28
DVD Setup................................................................................................................................ 29
Troubleshooting ................................................................................................................. 30
Specifications ....................................................................................................................32
- 1 -
Features
DVD, CD, MP3, Picture CD compatible
CD-R, CD-RW capable
TV format:
PAL/NTSC color system
4:3/ 16:9 Screen format select
Video output:
Scart (AV, R-G-B) output
Composite Video output
S-Video output
Audio output:
Down-mix stereo output
Dolby Digital down mixed stereo power output
Dolby Digital digital output
Headphone jack x 1
DVD features:
Multi Subtitle select
Multi Language select
Multi Angle select
Radio Features:
RDS FM/AM digital PLL tuning
40 Radio channels preset memory
Amplifier features:
Speaker outputs 2 x 20W (4 Ohms)
Loudness selection
Treble / Bass/ Balance/ Sound Effect/ Volume
Other features:
On screen control menu
Remote volume
Digital zooming
Slow motion forward
Child lock
Auto screen saver
Sleep function
Manufactured under license from Dolby Laboratories.
Dolby and the doubled-D symbol are trademarks of
Dolby Laboratories,. Confidential Unpublished Works.
1992-1997 Dolby Laboratories. All rights reserved.
Safety Information
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
To reduce the risk of fire and electric shock, do not remove the cover (or back) of the unit. Refer servicing only to qualified service personnel.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the product enclosure constitute a risk of electric shock.
equilateral triangle is intended to alert the user to the presence of important instructions in the literature accompanying the appliance.
4. Water and Moisture-do not use this video product near water for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool and the like.
5. Accessories-Do not place this product on an unstable cart, stand, tripod, bracket, or table, the product may fall, causing serious injury to a child or adult as well as serious damage to the product. Use this product only with a cart, stand tripod, bracket, or table recommended by the manufacturers or sold with the product. Any mounting of the product should follow the manufacturers instructions and use of a mounting accessory recommended by the manufacturer.
A product and cart combination should be moved with care. Quick stops. excessive force, and uneven surfaces may cause the product and car combination to overturn.
1. Read and Follow Instructions - All the safety and operation instructions should be read before the product is operated. Follow all operating instructions.
2. Retain Instructions-The safety and operation instructions should be retained for future reference.
3. Heed Warnings-All warnings on the product and in the operating instructions should be adhered to.
- 2 -
6. Ventilation-Slots and openings in the case are provided for ventilation to ensure reliable operation of the product and to protect it from over heating. These openings must not the blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a book case or rack, unless proper ventilation is provided or the manufacturers instructions have been adhered to.
7. Heat-The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that products heat.
8. Power Sources-This video product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your video dealer or local power company. For video products intended to operate from battery power, or other sources, refer to the operating instructions.
9. Power Cord Protection-Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the video product.
10. Power Lines-An outside antenna system should not be located in the vicinity of overhead power lines, other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching or approaching such power lines or circuits, as contact with them might be fatal. Installing an outdoor antenna can be hazardous and should be left to a professional antenna installer.
11. Cleaning-Unplug this video product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
12 Lightning-For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system.
This will prevent damage to the product due to lightning and power line surges.
13. Object and Liquid Entry- Never push objects of any kind into this product through openings as they may touch dangerous voltage points do short-out parts could result in a fire or electric shock. Never spill liquid of any kind on the product.
14. Servicing-Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
15. Overloading-Do not overload wall outlets or extension cords as this can result in a risk of fire or electric shock.
16. Damage Requiring Service-Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a) When the power-supply cord or plug is damaged.
b) If liquid has been spilled, or objects have fallen into the product.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by operating instructions. Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.
e) If the product has been dropped or cabinet has been damaged.
f. When the product exhibits a distinct change in performance-this indicates a need for service.
17. Replacement Parts-When replacement parts are required, have the service technician verify that the replacements he uses have the same safety characteristics as the original parts. Use of replacements specified by the video product manufacturer can prevent fire, electric shock, or other hazards.
18. Safety Check-Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks recommended by the manufacturer to determine that the video
product is in safe operation condition.
- 3 -
Introduction
About DVD
DVD is a digital video medium under the MPEG II format, featuring a variety of revolutionary entertainment capabilities. The MPEG II video compression technology provides capacity for an excellent picture of minimum 500 lines resolution on screen, up to 8 language sound tracks, up to 9 views from different camera angles and up to 32 language subtitles (provided the DVD disc itself supports these features).
Disc information
Disc types DVD CD
Recording
Method
Digital/MPEG II Digital
Capacity Single-layer/Single side 650MB = 74min
4.7 GB = 2 hr
Single-layer / Double sides
8.5 GB = 4 hr
Double-layers / Single side
9.4 GB = 4.5 hr
Double-layers / Double sides
17 GB = 8 hr
Disc size 12cm / 8cm 12cm / 8cm
Horizontal 500 lines up -
Resolution
Sub-titles 32 -
Sound tracks 8 1
Symbol
DVD features symbols
Each DVD disc contains various features depending on production of the disc. Below are some of the symbols representing the features:
Regional code / Video output system
Dolby Digital Surround Screen Format
DTS Digital Surround Child Lock
Number of Audio Tracks Angle indicator
Number of Sub-titles
Note:
The player has built in copyright protection technology that prevents copying from a DVD disc to any media.
If a video recorder is connected to the player, the video output image will be distorted during recording.
Some features contained in this DVD player are related to the DVD disc s software.
Some features cannot be performed if the disc does not support the feature, or requires special settings.
Select a DVD disc
DVD discs and DVD players are manufactured under the worldwide agreed DVD Regional Code
System that the player will operate only with corresponding disc of the same Regional Code.
About MP3
MP3 (MPEG 1, Audio Layer 3) is a digital audio format for quick downloading files that sound as good as CDs. MP3 uses entropy encoding to reduce the number of redundant sounds in an audio signal to a minimum. It takes music from a
CD and reduces it by a factor of 12, with no noticeable loss of quality. On a normal CD of 74 minutes you can store over 130 songs.
Disc information
Sampling rate should be 44.1 kHz and bit rate is recommended within the range from 128 Kbps to
256 Kbps, in order to achieve the best performance. In general, higher quality settings result in larger file sizes.
Tips for making a good MP3 CD
* System Requirement (Recommended):
IBM PC or compatible 200 MHz or faster
Windows 95/98/ME/XP/NT/2000 32MB RAM 205 MB free hard disk space (at least 140 MB of this space must reside on the system boot drive)
CD-Recordable or CD-ReWritable driver Windows compatible sound card 16-bit or better (optional).
* Using a good quality CD-RW disc. CD-R Gold Ultima is recommended. Up to 650 MB (74-minute CD) or
700 MB (80-minute CD) of MP3 files can be recorded.
* Select a high quality and stable CD Recorder (Writer).
HP CD-Write+9200 is recommended.
* Select an advanced CD burning software. Easy CD
Creator 4.0 or higher version is recommended.
* MP3 is data and not WAV information as such Mode
1 must be selected when compiling and burning your discs.
* Drag and drop (Direct CD) must not be used to compile the disc. The player will not recognize the format.
* Only single session recordings can be used.
Multi session recordings are not recognized and will not be played
* Select Data CD Project (software user interface), file system should comply with the standard of ISO 9660.
Or select MP3 CD Project for convenience operation
(available in Easy CD Creator 5.0)
* It is advised to finalize the CD after burnt.
Note * Playback of MP3, CD-R and CD-RW may depend on recording conditions.
- 4 -
This player is compatible to the following disc types:
DVD single sided/double sided single layered/double layered
CD-DA
CD-MP3
Kodak Picture CD
CD-R/CD-RW*
Note: Some PC application files on CD-R or
CD-RW can not be accepted by the unit, e.g. CD-ROM under PC Windows, etc.
(CD-R/CD-RW writing format may be different, some discs are not acceptable)
No-play disc
The following discs are not acceptable by the DVD player:
* DVD disc with region code that does not match the player s region code (Check the disc s region code printed on the disc packing.
Region code ALL will be acceptable by all players.)
* Some DVD discs that were purchased outside
the application country.
* PC application on CD-R/CD-RW.
* CD-ROM for PC interface only.
* MP3 CD-R/CD-RW of not proper format.
Care of disc
Video disc contains high-density compressed data that needs proper handling.
* Hold the disc with fingers. Hold the disc outer edge and/or the center spindle hole. Do not touch the disc surface.
* Do not bend or press the disc. Do NOT expose the disc to direct sunlight or heating sources.
* Store discs in cabinet vertically, in dry condition.
Prevent exposure to:
* Direct sunlight
* Heat or exhaust from a heating device.
* Extreme humidity.
* Clean the disc surface with a soft, dry cleaning cloth. Wipe the disc surface gently, radically, from center toward the outer edge.
* Do not apply thinner, alcohol chemical solvent, or sprays when cleaning. Such cleaning fluids will permanently damage the disc surface.
- 5 -
About the player
Front panel
Eject button
DVD mode:
Play/Pause/Step
Tuner mode:
Radio preset program store/APP(Auto
Program Preset)
Display panel Disc Tray DVD mode:
Disc Chapter Skip button
Tuner mode:
Radio preset channels skip
DVD mode:
Stop
Tuner mode:
Radio tuner function
AM/FM select
Power button
Loudness button
Headphone jack
DVD mode:
Disc Search buttons
Tuner mode:
Radio frequency search
Main volume:
Turn to adjust level/
Change selection
Remote sensor
Function button
DVD or AM/FM Tuner/
Treble/Bass/Balance/
Sound Effect/Volume
Rear panel
FM antenna input
System Connection
AM antenna input
Optical Digital Audio
Coaxial Digital Audio
Scart
(V,L,R,R-G-B)
Composite Video
S-Video
Down Mix Audio
Right/Left
Speaker outputs
Front Right/Left
- 6 -
Remote control
Some features of the player can only be performed by the remote control.
Loading and changing the batteries
Remove the cover of the battery compartment on the rear of the remote control. Insert two AAA
(UM-4 or R03) batteries into the compartment, take care to observe the + and - markings indicated inside, then close the cover.
Note * The batteries may last approximately one year depending on how much the remote control is used.
* For the best performance it is recommended batteries be replaced on a yearly basis, or when remote operation becomes erratic.
* Do not mix old and new batteries.
* Do not expose batteries to heat or try to dismantle them.
* Always remove batteries as soon as they become weak.
- 7 -
1. Disc Eject
2. Angle select (disc feature)
3. Numeric entry
4. Goto time search
5. Cursor (Up/Down/Left/Right)
6. PAL/NTSC/AUTO switch
7. Setup menu
8. Stop: Press once-Stop
(may resume with Play button)
Press twice-Stop
9. Volume adjust (Control level adjust)
10. Control mode select
11. Audio Equalizer
12. Clock function setup
13. Repeat playback
14. Power standby On/Off
15. Function select (DVD/Tuner)
16. DVD Subtitle select (disc feature)
17. DVD Audio Track (disc feature)
18. Clear the last entry
19. Return to the upper menu
20. DVD mode: Program Setting
Tuner mode: Radio preset channel memory store/
Auto program preset
21. Enter
22. Return to DVD disc Menu
23. Return to DVD disc Title
24. Play
25. Pause/Step: Press once to Pause
Press again to play frame by frame
26. Disc skip forward (Radio channel+)
27. Disc skip backward (Radio channel-)
28. DVD mode: Disc search forward
Tuner mode: Press: tune frequency up
Press and hold: auto search next channel up
29. DVD mode: Disc search backward
Tuner mode: Press: tune frequency down
Press and hold: auto search next channel down
30. Zoom [Radio Band FM/AM select]
31. Slow forward (Radio Mono/Stereo select]
32. Screen Chart Display selection
33. Mute (Speaker)
34. Set the clock selection
35. Confirm clock input
36. On Screen Display On/Off
37. Repeat section A to B
System connection
Connecting to TV set (Video connection)
Connecting to the
TV set Scart
FM - AM +
Antenna
Digital audio
Bitstream/LPCM
Coaxial
Optical
R-G-B/Video/Down mix audio
Composite
Video
Down mix
Video S-Video
Serial number MADE IN CHINA
Connecting to the
TV set Composite video (V)
Video (Composite)
Audio (Down mix stereo)
Yellow
Inptut 1 Inptut 2 Outptut
Video Video Video
White
Red L L L
Audio
R
Input
Audio
R
Input
Audio
R
Output
TV Back panel
S-Video
Connecting to the TV set S-Video
Scart
Video/Down mix Audio/RGB TV Atenna
Scart (AV, R-G-B)
1. For a TV with scart jack, connect the player s
scart jack to the TV s scart jack. The scart
jack contains R-G-B video output, composite
video output and down mix stereo left and
Right audio output.
2. For a TV without scart jack, connect the player s down mix audio left (L) and right (R)
output to the TV s audio left and right input.
Connect either one of the players video output
(Video or S-video) to the TV s corresponding
video input.
Note * The player is equipped with Scart
(AV, R-G-B), S-Video and Composite Video output port select. Enter the SETUP menu to select the suitable video port.
* If the TV set has more than one composite input, you may choose either one to connect.
Make sure you have properly connected the video and audio ports, and switch the TV channel to the corresponding input (e.g. AV1,
AV2,..etc.)
Default setting: Video and Scart (AV, R-G-B)
If the TV set is equipped with scart (R-G-B), connecting this signal will provide the best picture quality.
- 8 -
Connecting to Speakers
L
R
+ -
Connect the two speakers to the player s speaker connection outputs:Front R.(Right) and Front L.(Left)
Connecting the Antenna
FM - AM +
Connecting the AM antenna to the player s AM antenna input.
Note * EXtend the FM antenna as long as you can, so as to maximize the receiving power.
* Turn the antenna to different directions in order to reach the best receiving position.
- 9 -
Connecting to External Amplifier
Stereo amplifier
Digital decording amplifier
The player provide audio outputs for external stereo amplifier, or external digital amplifier (with Dolby
Digital decoding).
To connect a stereo amplifier, connecting the player s audio out L (left) and R (right) to the stereo amplifiers audio input left and right, select the corresponding mode of the amplifier.
To connect a digital amplifier, connecting the player s digital audio Coaxial output or Optical output to the digital amplifiers digital input with a coaxial cable or optical cable (These cables are not included), select the corresponding mode of the amplifier.
Note * The player is equipped with DOLBY
DIGITAL digital output, and DOLBY
DIGITAL down mixed stereo power output.
* When digital output is in use, enter the
SETUP menu to set the digital output to
RAW or PCM.
Connecting a Headphone
Insert the headphone to the PHONE input jack.
When a headphone has been connected, the player will detect automatically, the speakers output will be cut and the phone level can be adjusted.
Push the FUNCTION button to select the mode.
(TREBLE/BASS/BALANCE/SOUND EFFECT/VOLUME)
Turn the knob clockwise to increase the level or change selection.
Turn the knob anti-clockwise to decrease the level or change selection.
- 10 -
Setting up the player
Video port setup
The DVD player is equipped with the following video ports:
Composite Video(V) (Always active)
Scart(AV, R-G-B) (Default option)
S-Video
The DVD player has been preset at the factory to Composite Video(V) and Scart(AV,R-G-B) outputs, as default settings.
If any other video port has been connected and an incorrect pictured appears on screen, set the desired video port step by step, as follows:
For S-Video or RGB output selection,
the following set up is required:
After system connection is completed, setup as following steps:
1
Press SETUP button, SYSTEM menu appears.
2
Highlight VIDEO OUTPUT selection, press cursor LEFT/RIGHT button to change setting.
RGB (Scart output) S-VIDEO
3
Press SETUP button to quit.
IMPORTANT NOTE:
Either ONE of RGB or S-Video output can be selected as the optional video output.
TV System
For TV System setting
TV System menu is to set up the output TV system to PAL or NTSC (Default setting is PAL):
AUTO: Auto switch to PAL or NTSC system according to the disc.
NTSC: NTSC TV system
PAL : PAL TV system
1
Press SETUP button, SYSTEM menu appears.
2
Highlight TV OUTPUT selection, press cursor LEFT/RIGHT button to change setting.
PAL AUTO NTSC
3
Press SETUP button to quit.
Note: * When a DVD disc of NOT correct format (region code) is loaded, the player will not accept the disc and message REGION! will be displayed on screen.
* When a DVD disc of NOT correct TV system is loaded or the TV set of NOT correct
TV system with the player, a distorted video signal may come out on the screen.
- 11 -
Set up the Timer
1
Set up the Clock
In STANDBY mode, Press CL. ENTER button, to start setup.
2
Press SET button, to switch between AM and PM.
Press CL.ENTER button to confirm and jump to next setting.
3
Press SET button, to increase the time for 1 hour each.
The range of time is 1 to 12 hours.
Press CL.ENTER button, to confirm and jump to next setting.
4
Press SET button, to increase the time for 1 minute each.
The range of time is 0 to 59 minutes.
Press CL.ENTER button to confirm and return normal mode.
Auto On Setting
Press CLOCK button, the VFD display will show the word
(ALA SET).
1
Press CL.ENTER button, to confirm and start to set.
2
Press SET button, to switch between AM and PM.
Press CL.ENTER button to confirm and jump to next setting.
3
Press SET button, to increase the time for 1 hour each.
The range of time is 1 to 12 hours.
Press CL.ENTER button to confirm and jump to next setting.
4
Press SET button, to increase the time for 1 minute each.
The range of time is 0 to 59 minutes.
Press CL.ENTER button to confirm and jump to next setting.
5
Press SET button, to set Auto On function active or disable.
Press CL.ENTER button to confirm and return normal mode.
1
SLEEP
Press CLOCK button repeatedly, until the VFD display show the word (SLE SET), press CL.ENTER button to confirm and start to set.
2
Press SET button, to increase the time for 15 minutes each.
The range of time is 0 to 120 minutes.
Press CL.ENTER button to confirm and jump to next setting.
Using the SLEEP to set the sleeping time, the sleep function will apply once only.
HOURS
CLOCK
MINUTES
MINUTES
TO SLEEP
- 12 -
Getting started
* Unpack the unit.
* Read through this manual before installation and use.
* Load batteries into the remote control unit.
* Connect the system, make sure the connections are secured.
* Connect the power plug to the AC power outlet.
Remark
Some feature contained in this DVD player are related to the DVD disc s software.
Some features cannot be performed if the disc does not support the feature, or requires special settings.
Check the features printed on the disc s packing or follow the instructions of the Discs on screen menu.
Selecting a function DVD/TUNER
Switch on the player
Press the main power button to turn on the DVD unit. Power on the TV set and the amplifier if connected.
Set up the system
Select the corresponding setting of the TV set ( AV1, AV2, S-Video etc.) and the amplifier, until the
DVD power on screen appears.
The function mode will be memorized by the player when power off.
1
2
Choose the mode
Press FUNCTION button on the front panel
Turn the volume knob on the front panel or
Press DVD/TUNER button on the remote to start selection.
* DVD mode
* FM Band mode
* AM Band mode
DVD/TUNER
BUTTON
VOLUME
KNOB
FUNCTION
BUTTON
- 13 -
Sound Adjustment
Adjust the audio quality
Press FUNCTION button on the front panel repeatedly until the VFD display show the word (TREB 00) or press MODE button on the remote.
Repeat pressing FUNCTION button on the front panel or
Repeat pressing the MODE button on the remote to select different audio adjustment mode.
TREBLE BASS BALANCE
To increase the level:
Turn the volume knob clockwise or
Press the upper edge of the remote VOLUME button.
To decrease the level:
Turn the volume knob anti-clockwise or
Press the lower edge of the remote VOLUME button.
Adjust the output volume
Press FUNCTION button on the front panel repeatedly or
Press MODE button on the remote repeatedly until the VFD display show the word (VOL 00).
To adjust the output volume up:
Turn the volume knob on the front panel clockwise or
Press the upper edge of the remote VOLUME button
To adjust the output volume down:
Turn the volume knob on the front panel anti-clockwise or
Press the lower edge of the remote VOLUME button.
VOLUME
MODE
Select the sound effect
Press FUNCTION button on the front panel repeatedly until the VFD display show the word of sound effect.
To select the next sound effect:
Turn the volume knob clockwise.
To select the previous sound effect:
Turn the volume knob anti-clockwise
Or press EQ button on the remote to select the sound effect in sequence.
DIRECT JAZZ DISCO HALL
Loudness function
When loudness function is active, it adds compensation to bass sounds that are hard to hear at low volume.
Press LOUD ON/OFF button on the front panel to activate loudness function, the VFD display shows the word LOUD ON and then LOUD indicator will appear on the VFD display.
Press LOUD ON/OFF button on the front panel again to disable loudness function, the VFD display shows the word LOUD OF and then LOUD indicator will disappear from the VFD display.
The adjusted level will be memorized by the player.
- 14 -
DVD Mode
Switch on the player
Press FUNCTION button on the front panel
Turn the volume knob on the front panel or
Press DVD/TUNER button on the remote until the
VFD display shows the word (DVD).
OPEN
Load a disc
Press OPEN button on the remote control (or front panel) to open the disc tray. Load a disc and press
OPEN to close the disc tray.
Automatic Play
The unit will take a few seconds to download the disc initial data, display the disc type logo at the right upper corner of the TV screen, and then start playing automatically.
CURSOR
If a DVD disc menu appears on screen
Press CURSOR buttons to select the desired feature in the menu.
And then press the ENTER button to confirm a selection.
ENTER
For more DVD features, see in the chapter
FUNCTION BUTTONS.
NOTE: * Normally, when a MP3 disc is loaded, the unit will take longer time to download the initial data.
* Returning to the disc main menu, press MENU button on the remote.
Problem disc messages
Incorrect disc format
When a DVD disc of incorrect format (region code) is loaded. The player will not accept the disc and the message (REGION!) will be displayed on screen.
Production qualities of DVD discs vary, some discs might deviate from the industrial standard. Some incorrectly formatted discs may playback on the player. However, the playback and operational quality of those discs may be substandard.
- 15 -
Tuner Mode
Switch on the player, make sure the antenna has been properly connected.
Select a radio band FM or AM
Press FUNCTION button on the front panel
Turn the volume knob on the front panel or
Press BAND button on the remote to switch between FM and AM receiving.
Tune a channel
The player equipped with a built-in digital PLL tunning system, with automatic search function.
FREQUENCY
CHANNEL
To auto search the next higher frequency channel:
Press and hold the upper FREQUENCY button on the front control until the VFD display shows the word AUTO or press and hold the SEARCH button on the remote control until the VFD display shows the word AUTO.
To auto search the next lower frequency channel:
Press and hold the lower FREQUENCY button on the front control until the VFD display shows the word
AUTO or press and hold the SEARCH button on the remote control until the VFD display shows the word AUTO.
Press the FREQUENCY / panel slightly, or press the SEARCH / frequency up or down.
button on the front
button on the remote control slightly to fine tune the
To store a preset program
The player provide 20 preset program memory for each radio bands.
To store a preset program, tune a channel:
Press FUNCTION button on the front panel,
Turn the volume knob on the front panel.
or
Press BAND button on the remote to switch between
FM and AM receiving.
Press FREQUENCY button on the front panel or press SEARCH button on the remote to tune the desired frequency.
Press PROG/MEMORY button to store.
Press CHANNEL button on the front panel or press
SKIP button on the remote to select the desired preset channel.
- 16 -
PROG/MEMORY
SKIP/CHANNEL
SEARCH/
FREQUENCY
BAND
CHANNEL
FREQUENCY
VOLUME
KNOB
FUNCTION
Search a preset program
Press the CHANNEL button on the front panel or press the SKIP button or the Numeric keys on the remote.
Weak FM signal
When the stereo FM receiving signal is weak, some noise may come up. In this case,
Press ST/MONO button, switching the tuner to mono mode in order to reduce the noise.
(Press ST/MONO button again, switching back to stereo mode)
RDS reception
RDS stands for Radio Data System and is a signal that transmits data with FM broadcasts. When an
RDS broadcast is received, the station name appears on the main unit displaying for about 3 seconds and the RDS indicator lights up.
Switching the display
Each time you press the RDS button on the remote, the display will switch as below:
Programme Service name mode mode
Frequency
Setting in Station name mode and Frequency mode will change the broadcast source but this is cancelled when the unit is turned off.
PTY (Program Type) list (for reference)
1. NEWS (News) 15. OTHER M
(Other music)
2. AFFAIRS (Current affairs) 16. WEATHER (Weather)
3. INFO (Information) 17. FINANCE (Finance)
4. SPORT (Sport) 18. CHILDREN
5. EDUCATE (Education)
6. DRAMA (Drama)
7. CULTURE (Culture)
8. SCIENCE (Science)
9. VARIED (Varied)
10. POP M (Pop music)
11. ROCK M (Rock music)
(Children programs)
19. SOCIAL (Social affairs)
20. RELIGION (Religion)
21. PHONE IN (Phone in)
22. TRAVEL (Travel)
23. LEISURE (Leisure)
24. JAZZ (Jazz music)
25. COUNTRY
(Country music)
12. EASY M
(Easy listening music)
26. NATION M
(National music)
13. LIGHT M (Light classical) 27. OLDIES (Oldies music)
14. CLASSICS
(Serious classical)
28. FOLK M (Folk music)
29.DOCUMENT
(Documentary)
- 17 -
PRESET
CHANNEL
Screen saver
The player is equipped with an automatic screen saver, for the purpose of protecting the TV screen.
The TV screen will be black and a screen saver will appear on screen if:
* No disc is loaded for 15 seconds
* In STOP mode and no button has been pressed for 15 seconds. (except in the player or disc menu)
When any button is pressed, the player will resume to normal active mode.
Power management (In DVD mode only)
The player is equipped with an energy saving power management.
In STOP mode and no button has been pressed for 5 minutes, the player will switch off to standby mode automatically.
Function buttons
Power ON/OFF
To switch the player on or standby off:
Press STANDBY button on the remote or POWER button on front panel.
(Always switch off the player to standby mode after use)
Eject disc
To eject the disc: (In DVD mode only)
Press EJECT button on the remote or EJECT button on the front panel.
EJECT
1
Play/Pause/Step/Stop
Press PLAY button to play the disc.
2
Press PAUSE button to pause.
Repeat pressing the button to step forward the still picture frame by frame.
Press PLAY button to resume normal playback.
3
Press STOP button to stop in two modes: a) Press Once: STOP memorizes the interrupt
position.
(May res ume with play button) b) Press Twice: To stop completely.
(Will NOT resume with play button)
- 18 -
STANDBY
Skip Forward/Backward
Press SKIP button to skip forward (chapters)
(Search the next preset channel in tuner mode)
Press SKIP button to skip backward (chapters)
(Search the previous preset channel in tuner mode)
ENTER
1
Search Forward/ Backward
Press SEARCH button to search forward.
(Search the next higher frequency channel)
Repeat pressing the button to change search speed.
2 4 8 16 32
PAUSE
STOP
2
Press SEARCH button to search backward.
(Search the next lower frequency channel)
Repeat pressing the button to change search speed.
2 4 8 16 32
3
Press PLAY button to resume normal playback
Player will not advance or reverse during
WARNING section of any disc.
1
Slow Forward
Press SLOW button to play slow forward.
Repeat pressing the button to change slow forward speed
1/2 1/4 1/8 1/16 1/32
CLEAR
RETURN
PLAY
SKIP
SEARCH
SLOW
OSD
The unit muted in SERCH and
SLOW mode.
2
Press PLAY button to resume normal playback.
Select an item in menu
In the disc menu or setup menu
1
Press CURSOR button to move between function items.
2
Press ENTER button to confirm a selection.
3
4
Following function does not apply to some DVD disc:
Press RETURN button to return to the previous menu.
Press CLEAR button to cancel an entry.
On Screen Display Menu
Press OSD button to switch the OSD indicator on or off.
- 19 -
Disc Title/Menu
Press MENU button return to the DVD disc Menu.
Press TITLE button return to the DVD disc Title.
Disc MENU: Disc menu is a DVD disc feature, allowing users to select functions on screen.
Disc TITLE: Disc title is the beginning track of a DVD disc. Some DVD discs refuse the TITLE function.
GOTO a desired section
Press the GOTO button to play at a desired Title,
Chapter or Time.
This function does NOT apply to MP3 & Picture CD.
DVD disc
Press the GOTO button to Time search mode.
Press the GOTO button again to Title and Chapter mode.
Press LEFT/RIGHT button highlight the desired item.
GOTO
TITLE
MENU
--:--:-Input time hh:mm:ss
T --
C --
(Hour:Minute:Second)
Input title number
Input chapter number
Press ENTER button.
Time search mode Title, chapter search mode
CD disc
Press the GOTO button to Time search mode.
Press the GOTO button again to Track search mode.
--:--:-- Input time hh:mm:ss
(Hour:Minute:Second)
T - Input track number XXX
(Track Number)
Press ENTER button.
Track search mode
Note * GOTO functionality depends on different DVD discs format. Some DVD discs do not allow GOTO function.
* GOTO will cancel program playback.
Repeat
Press REPEAT button repeatedly to select the desired repeat mode.
DVD disc
REPEAT CHAPTER
REPEAT TITLE
REPEAT OFF
CD disc
REPEAT TRACK
REPEAT DISC
REPEAT OFF
Repeat the chapter
Repeat the Title
Repeat function off
Repeat the existing track
Repeat all tracks
Repeat function off
Note * Repeat functionality depends on different disc s production format, some DVD discs do not allow repeat function.
* Repeat function does not function during
Program playback and Repeat A-B playback
- 20 -
Repeat the section A-B
To repeat playback of a desired section:
1) Press the A-B button, at the beginning of the desired section, A
2) Press the A-B button again, at the end of the desired section, B
The player will repeat playing back the section from A to B.
Press the A-B button again to cancel the function and return to normal play.
Note * A-B repeat depend on different disc s production format, some DVD discs do not allow repeat function.
* A-B function does not apply to MP3 disc
* The period between A and B should be at least 3seconds.
* A-B does not function during Program playback and Repeat function playback.
Zoom
In DVD mode
Press the ZOOM button (For DVD and Picture CD playback only) to enlarge viewable picture.
Press the button repeatedly to change the zoom scale:
X2 X4 NoZoom
Press the CURSOR buttons to adjust the zooming position.
NOTE * The picture quality is degraded as the picture is increased.
* The function is applicable to DVD and picture CD playback only.
Random Program access
Input the desired Chapter or Track number using the numeric key. Press ENTER button to confirm your direct access Chapter or key selection.
* Chapter-when playing a DVD disc, or
* Track-when playing a CD, MP3 disc
* Channel-when switching to tuner
Numeric input-Function/Menu
Press the numeric key to input data for disc or setup menu.
Note * Program functionality depends on different
DVD disc s format, some DVD discs do not allow direct access function.
- 21 -
Multi-Subtitle
If a DVD disc contains the Multi-Subtitle feature, subtitle may be selected:
While in playback, repeat pressing SUBTITLE button to select the desired subtitle.
Status will be displayed on screen.
Total subtitle
Current subtitle
Note * A DVD disc may contain up to 32 subtitle selections.
Multi-Audio Sound track
If a DVD disc contains Multi-Audio Sound track feature,
Voice Language can be selected.
While in playback, repeat pressing AUDIO button to select the desired audio language. Status will be displayed on screen.
Total language
Current language
A CD disc contains two channels stereo sound tracks,
Left and Right. The function can change to Left and Right channel mono output in DOWN MIX audio mode.
NOTE * A DVD disc may contain up to 8 audio language selections.
* In most cases, an Audio Sound track selection will be displayed on a DVD disc start up menu, press cursor button to select and ENTER button to confirm.
Multi-Angle
If a DVD disc contains Multi-Angle feature, viewing angles may be selected:
While in playback, repeat pressing ANGLE button to select the desired viewing angle. Status will be displayed on screen.
Note * A DVD disc may contain up to 9 selectable viewing angles.
Total angles
Current angle
- 22 -
ST/MONO
When the stereo FM receiving signal is weak, some noise may come up. In this case,
Press ST/MONO button (In Tuner mode only) switching the tuner to mono mode in order to reduce the noise.
(Press ST/MONO button again, switching back to stereo mode)
Radio Band
Press BAND button repeatedly, switch the tuner between FM and AM mode. (In Tuner mode only)
On the panel, repeat pressing the BAND button, switch the tuner between FM and AM mode.
Mute
Press MUTE button on the remote to mute (turn off) the audio output (speakers).
Press the button again to resume normal audio output
(speakers).
Volume/Mode
Adjust the audio quality
Press MODE button on the remote
Repeat pressing the MODE button on the remote to select different audio adjustment mode.
TREBLE BASS BALANCE
To increase the level:
Press the upper edge of the remote VOLUME + button.
To decrease the level:
Press the lower edge of the remote VOLUME - button.
Adjust the output volume
Press MODE button on the remote repeatedly until the VFD display show the word (VOL 00).
To adjust the output volume up:
Press the upper edge of the remote VOLUME + button.
To adjust the output volume down:
Press the lower edge of the remote VOLUME - button.
EQ
Press EQ button on the remote to select the sound effect in sequence
Below is the sequence of available sound effect:
DIRECT JAZZ DISCO HALL
- 23 -
Display
Press DISPLAY button on the remote to select the screen chart display on the VFD.
DVD/TUNER
Press DVD/TUNER button to switch between DVD, Tuner function mode.
Repeat pressing the button to select the mode
DVD Radio Tuner
PAL/NTSC switch
Press PAL/NTSC button to switch the player between PAL, NTSC and Auto system
Clock
Press CLOCK button on the remote to set the time of Auto
ON and Sleep function.
CL.ENTER
Press CL.ENTER button on the remote to confirm Clock function selection.
Set
Press SET button on the remote to set Clock desired selection.
Memory
To store a preset program
The player provide 20 preset program memory for each radio bands.
To store a preset program, tune a channel:
Press BAND button on remote to switch between FM and AM receiving.
Press SEARCH button on the remote to tune the desired frequency.
Press PROG/MEMORY button to store.
Press SKIP button on the remote to select the desired preset channel.
Search a preset program
Press the SKIP button or the Numeric keys on the remote.
- 24 -
Program setting
Program to play a DVD, CD disc in a desired sequence automatically.
This function does NOT apply to MP3 &
Picture CD
DVD program menu
Load a DVD disc.
1
Press the PROG button, the DVD program menu will appear.
2
Use numeric key to input the Title number and the Chapter number, press ENTER button to confirm.
Repeat step 2 until programming is completed.
3
To quit the programming, press PROG button to exit the program menu.
4
Press PLAY button to rum Program Play.
5
Press STOP button to cancel the program.
Input Title and Chapter
Range of selection
CD program menu
Load a CD disc.
1
Press the PROG button, the CD program menu will appear.
2
Use numeric key to input the Track number, press
ENTER button to confirm.
Repeat step 2 until programming is completed.
Input Track
Range of selection
3
To quit the programming, press PROG button to exit the program menu.
4
Press PLAY button to rum Program Play.
5
Press STOP button to cancel the program.
Note * Some DVD discs do not allow programming.
* Program playback does not function during Repeat function and Repeat A-B playback.
On Screen Display
Press OSD button, an On Screen Display (OSD) indicator will be displayed at the upper part of the
TV screen in displaying the disc information and operation status.
The OSD indicator will remain on screen until pressing the OSD button to turn it off.
When a different disc is loaded (DVD, CD), the OSD indicator bar will be different.
- 25 -
OSD-DVD mode
Audio Sound track
Disc playback time Disc Title Chapter Disc remain time Audio format
Selected language
Chapter playback time/
Chapter remain time
Disc Subtitle
Multi-angle
OSD-CD mode
Disc remain time
Disc Track
Track playback time
MP3 and Kodak Picture CD mode
Upper folder
Current folder
Disc playback time
Selected file highlight
* After you have selected a file, press PLAYbutton to play this file.
* When the file is playing, press
STOP button to return selection.
Playback time /Total time
Browse display mode
Playback mode
Select the browse and playback mode
In STOP mode, press cursor LEFT/RIGHT button to switch between file browse and selection box.
Press cursor UP/DOWN button to highlight the desired item.
Press ENTER button to change selection:
DISPLAY
* MP3 ONLY (Display all MP3 files only)
* JPEG ONLY (Display all JPEG files only)
* MP3 AND JPG (Display all MP3 and JPEG files together)
- 26 -
Select a file
In STOP mode, press CURSOR button to highlight the desired track, move to previous and next page.
Press ENTER button to play the selected track.
PLAY MODE (MP3 playback)
* NORMAL (Play till last track once in same folder)
* REPEAT DIR (Repeat play all in same folder)
* REPEAT ONE (Repeat play the same track)
* SHUFFLE (Repeat random play all in same folder)
Playback your MP3 CD
Press PAUSE button to pause.
Press STOP button to stop.
Press SEARCH button to search forward/backward.
(For MP3 PLAYBACK ONLY)
Press SKIP button to skip forward/backward (track).
Press PLAY button to resume play.
MP3 file format (limitations)
Sampling rate should be 44.1kHz and bit rate is recommended within the range from 128 Kbps to
256 Kbps, in order to achieve the best performance.
Playing back your Kodak Picture CD
The new feature enables the decoding of JPEG files from a Kodak Picture CD disk.
When a Kodak Picture CD has been loaded in the player, an automatic slide show will be launched.
Each picture in the Kodak Picture CD will be displayed consecutively in a slide-show fashion and will be scaled to fit in the whole TV screen.
Press PAUSE button to display an image indefinitely.
Press SKIP button to view the next or previous picture.
Press PLAY button to resume the slide show.
There are four modes to rotate a picture.
These operations are allowed only when a picture is being displayed normally and will be cancelled automatically when a new picture is displayed.
Press ARROW button to select the different rotation modes:
Press cursor RIGHT button to rotate 270 degree.
Press cursor LEFT button to rotate 90 degree.
Press cursor UP button to rotate 0 degree.
Press cursor DOWN button to rotate 180 degree.
About Kodak Picture CD
A Kodak Picture CD has the size and shape of a regular CD. You can order a KODAK Picture CD simply by checking the box on the photo finishing envelope when you drop off a roll of film (35mm or
Advanced Photo System (APS) color print film) at the time of processing in Kodak Express store displaying (Kodak Picture CD) sign. When your order is returned, you receive your prints, negatives, and your full roll of pictures safely stored on you KODAK Picture CD. Each KODAK Picture CD brings you the tools to enhance, share and manage your pictures on your computer.
Zoom
Both Zoom in and Zoom pan function for the pictures are provided.
Press ZOOM button to execute zoom function and select the zoom enlarging scale.
In zoom mode, Press ARROW button to adjust the zooming position, thus the position of the partial picture to be displayed. With zoom mode off, the next picture will be scaled to normal fitting to the whole TV screen.
Press ZOOM button to cancel the zoom and resuming to the slide show.
Note: During zoom function, slide show transition and image rotation are disabled.
Now, you can playback Kodak Picture CDs on our
DVD players and view your pictures on your TV in the comfort of your living room.
PLAY MODE (Picture CD playback)
* NORMAL (Disable playing slide show)
* REPEAT DIR (Repeat play slide show of the folder)
* REPEAT ONE (Repeat play the same file)
* SHUFFLE (Repeat play slide show randomly of the folder)
JPEG file format (limitations)
* JPEG file of CMYK color mode is not supported.
* The range of pixels should be not exceeding
3840 pixels x 3840 pixels, in order to achieve
the bes t performance.
Setup Menu
Various features of the player can be adjusted in the SETUP menu. Press SETUP button, SETUP menu appears.
Press cursor RIGHT button to switch to the desired setting menu.
Video
The player has a built in video equalizer, enter this menu to setup the video equalizer.
Press SETUP button, SETUP menu appears,
Highlight the video menu icon.
System
Enter this menu to setup the OSD language, screen saver ON/OFF, reset to default setting, TV output system and video output ports.
Press SETUP button, SETUP menu appears, Highlight the system menu icon.
Highlight the desired item and press cursor LEFT/
RIGHT button to change the setting.
Press SETUP button to save the setting and quit.
Highlight the desired item and, press cursor LEFT/
RIGHT button to change the setting.
Press SETUP button to save the setting and quit.
Default setting
Brightness
Contrast
Saturation
: Normal
: Normal
: Normal
Default setting
OSD language : English
Screen saver : On
TV output : PAL
Video ouput : RGB
Audio (digital audio)
Enter this menu to setup the digital audio output format between Bitstream, LPCM and Off.
Press SETUP button, SETUP menu appears,
Highlight audio menu icon.
TV output (system)
TV output menu is to set up the broadcast system:
AUTO/NTSC/PAL.
Video output (port)
Video output includes:
1) Composite video (V)
2) S-Video
3) RGB in Scart (Default)
Only one of the S-Video or RGB can be set to active, but not both.
Depends on your actual system connection, activate the correspondent video output.
- 28 -
Highlight the desired item and press cursor LEFT/
RIGHT button to change the setting.
Press SETUP button to save the setting and quit.
Default setting
Digital output : Bitstream
DVD Setup
The DVD SETUP menu is to setup the DVD features.
Press SETUP button, SETUP menu appears, Highlight DVD setup menu icon.
16:9 Wide Scr
When you connect to a wide screen TV, this setting will allow the original aspect ratio will be display full screen.
Note * Depending on the DVD disc format, e.g.
2.35:1, the wide screen setting may still having black margins above and below the picture.
Angle mark
Show or hide the display of ANGLE MARK when playing a DVD disc with multi-angle.
Highlight the desired item and press cursor LEFT/
RIGHT button to change the setting.
Press SETUP button to save the setting and quit.
Parental control
To setup the rating level of the player.
The player will require a password to play any disc with rating level higher than the setting.
Default setting
Menu
Audio
Subtitle
: English
: English
: Off
TV screen
Angle mark
: 4:3 LB
: ON
Parental control : 8
Password : 7890
Eject any disc, highlight (Password), input the 4 digits password, press ENTER button to confirm.
Default setting
Parental control : 8
Password : 7890
Menu/Audio/Subtitle
To setup the default language selection of a DVD disc, when a DVD disc has been loaded.
TV screen
The aspect ratio of the picture provided by the
DVD player can be varied in line with the features available on the TV in use.
Highlight (Parental control) selection, repeatedly pressing ENTER button to change the setting:
1. Kid Safe
2. G
3. PG
4. PG_13
5. PG_R
6. R
7. NC_17
8. Parental Con
Press SETUP button to save the setting and quit.
4:3 Letter Box
Allow you to see movies in their original aspect ratio.
Entire frame of the movie will be display on screen, but it will occupy a smaller portion of the screen.
Change Password
Highlight (Password) selection.
Input the 4 digits old password or default password.
Input the 4 digits new password.
Input the 4 digits new password again to confirm.
4:3 Pan Scan
Then signal will fill the screen with the centre of the picture. The left and right edge of picture may be cut outside range of the screen.
When new password accepted, (CHANGE OK) will be displayed.
- 29 -
Troubleshooting
Should your DVD player develop a problem, please check below before requesting service:
Symptom Check and Action
No Power
* Check if the power cord has been properly connected to the power outlet.
* Check if the main power has been switched on.
Does not play
No Picture
Picture noise/ distorted
* No disc, load disc.
* Disc has been loaded upside down. Place the disc with the label side up.
* The region code of disc does not match to the player.
* Disc is not correct type for the player.
* Disc is damaged or dirty, clean the disc or try another disc.
* Moisture may be condensed inside the player, Remove the disc and leave the unit power on for one or two hours.
* Check if the TV set has power on, use TV remote to select A/V signal for DVD rather than broadcast.
* Check if the system connection is proper and secure.
* Check if the connection cables are damaged.
* Clean the disc.
* The disc is dirty or damaged. Clean the disc or try another disc.
* Reset the color system of the player or the TV set.
* Try to direct the player to the TV set instead of via other components, such as a VCR.
Picture not full screen
Malfunction
* Select the screen format from the player s SETUP MENU, see (SETUP
MENU) of this manual.
* Select the screen format from DVD disc menu.
* Press and hold the power button on the front panel until the player power off. Or switch the main power switch on the rear panel off.
Power on again, the player will be reset.
* Should the player still develop a malfunction, unplug the player for 30 minutes. After 30 minutes, power on the player and the restore function should reset the player.
Cannot SKIP or
SEARCH
* Some discs are programmed that do not allow users to SKIP or
SEARCH at some sections, especially at the beginning WARNING section.
* Single Chapter disc cannot apply SKIP function.
- 30 -
Symptom Check and Action
No sound or sound output not complete
No surround sound
MP3 disc no sound or noisy
Picture CD disc can not play or distort
Remote control does not function
* Check if the TV, Amplifier and Extra active sub-woofer have been switched on, and correctly set.
* Check if the TV, Amplifier, Speaker system connection is secured.
* Press AUDIO button to select other audio tracks output of disc.
* Check if the MUTE function of the AV Receiver or TV or Amplifier has been activated.
* There will be no sound output during PLAY/PAUSE/STEP/SLOW and SEARCH.
* If digital output has been applied:
* Press SETUP button
* Highlight (Audio)
* Highlight the desired items
* Select BITSTREAM or LPCM
* Press SETUP button
* Power on the amplifier or active type loudspeakers.
* When PC program files or other data files are mixed with MP3 files in the same disc, the player may play the non-MP3 files with noise or no sound.
* Check the disc, if all the files on disc are MP3 files, skip the file, try other files.
* Check if the sampling rate of the file is 44.1 kHz and the bit rate is within the range from 128 Kbps to 256 Kbps.
* Check if the JPEG file is not CMYK format and the image size within 3840 pixels x 3840 pixels.
* Remove the obstacles between the remote control and the player.
* Point the remote control towards the remote sensor on the player.
* Check if the batteries of the remote control have been loaded with correct polarities.
* Replace the batteries of the remote control.
PROTECT displayed on LCD
Radio receiving weak
* Check if the audio noise output level from the disc or Tuner is too high.
* Check if the speaker cable is shorted or used the unmatched cable.
* Check the antenna connection.
* Extend the antenna as long as you can, so as to maximize the receiving power.
* Position the antenna to different directions in order to reach the best receiving position.
- 31 -
Specifications
Type of Disc
Video Format
Audio Format
Signal Output
Audio Power Output
Radio Frequency
S/N ratio
THD
Output Terminals
Input Jacks
Power input
Dimension
DVD
CD-DA
CD-MP3
CD-R/CD-RW
Kodak Picture CD
MPEG 2
MPEG 1, LAYER 1, LAYER 2, LAYER 3
Color System: PAL/NTSC
Audio System: DOLBY DIGITAL down mix stereo
DOLBY DIGITAL digital output
Audio DAC 24bit/96KHz
Video Output: 1 Vpp (at 75 ohm)
Audio Output (Stereo): 2 Vrms
RMS 13W X 2(4 ohm),at 10% THD
FM: 87.5MHz to 108MHz
AM: 531kHz to 1620 kHz
> 90 dB (LINE)
< 0.05% (LINE)
Scart output(AV,R-G-B) X 1
Video(composite) output X 1
S-Video output X 1
Down Mix Stereo output(Left and Right) X 1
2 channels power output X 1
Headphone jack X 1
Digital audio coaxial output X 1
Digital audio optical output X 1
FM antenna X 1
AM antenna X 1
220-240V AC ~50Hz
Body size : W160 x D250 x H70 mm (DVD player)
W160 x D270 x H140 (Amplifier)
Packing size : W625 x D330 x H350 mm
Net weight : 12.8Kg
- 32 -
AKAI ELECTRIC CO., LTD. JAPAN www.akai.com
Advertisement
