Furrion DV1100 Instruction Manual

Fig.1

Fig.2

A

B

Fig.3

+ side up

4

CONTRAST

It is for adjusting the contrast of the video output

HUE

It is for adjusting the hue of the video output.

SATURATION

It is for adjusting the saturation of the video output.

SHARPNESS

It is for adjusting the sharpness of the video output.

5.17.5 SPEAKER SETUP

DOWNMIX

It is for selecting your desired sound effect when there is no center speaker and subwoofer. There are 3 modes: LT/RT, STEREO, VSS.

LT/RT: When playing a disc with PRO LOGIC Dolby stereo effect, choose the

item, so it will output audio signal with vivid theatre effect.

STEREO: If you choose the item, when outputting audio signal with 5.1 channels,

it will output the left and right channels of signal ; when outputting audio signal

with 2 channels, it will output the common 2 channels of stereo signal.

VSS: If you choose the item, when playing a disc recorded with 5.1 channels,

the main channel speakers can output audio signal with VSS effect.

5.l7.6 OUTPUT SETUP

28

DYNAMIC RANGE

After selecting the compression mode of LINE OUT, set the item, so you can adjust the linear compression ratio. If you set it to be FULL, the Peak-to-Peak value of the audio signal is the minimum; if you set it to be OFF, the Peak-to-

Peak value is the maximum.

DUAL MONO

It is for selecting a desired audio output mode for the left and right ways of signal.

It is mainly for Karaoke of Ac3. There are 4 modes in all as follows:

STEREO, MONO L, MONO R, MIX MONO.

27

9

Disc USB Opreation

Insert Disc

Eject CD

With the label facing up,insert a disc into the Disc slot.

The disc will automatically begin playback.

Press

EJECT

toeject the disc

Track Select

Rotate

TRK >>| or TRK|<<

to skip to next or previous track/chapter.

Fast Forward

and Backward

Rotate and hold

TRK >>| or TRK |<<

to fast forwards or

backwards.

Pause

Playback

Press

>||

to temporarily stop the playback.

Press

>||

again to resume playback.

Stop

Playback

Press once to pause the playback,press

>||

to resume;

press twice to stop playback, then press

>||

to start playback

from the beginning of the first chapter/track.

Repeat

Random

Title

Press

RPT

to repeat current playing track/chapter.

Press

RPT

to resume.

Press

RDM

to play each track in random order.

Press

RDM

again to resume.

In DVD/VCD mode,press TITLE to display the title list.

BLUETOOTH OPERATION

Dial or

accept call

Press to accept, dial or redial a call.

Reject or

End call

Press to reject or end a call.

For the DVD System Menu, there are 6 setup pages in all. They display as follows:

5.17.1 SYSTEM SETUP

26

TV TYPE

The setup item is for matching TV screen size.

4:3 PS: Choose the item when connecting a TV set with 4:3 screen. When playing

the pictures with 16:9 size, the left and right parts of the video will be cut out,

and display in full screen.

4:3 LB: Choose the item when connecting a TV set with 4:3 screen. When playing

the pictures with 16:9 size, the top and bottom parts of the TV screen will be

turned into a black square respectively.

16:9: Choose the item when connecting a TV set with 16:9 wide screen.

PASSWORD

This setup item is for locking or unlocking the rating level of the Parental Control.

The defaulted state is locked. The defaulted password is 0000.

You can set a new password that you like: Select the PASSWORD item and then press the > button to enter it, then input the original password 0000, and then press the OK button to unlock it. Press the > button to enter it again, then input a new password that you like and then press the OK button to make it effective.

Before the other persons see the Manual, you should get the password in mind and cut out the part of PASSWORD in the Manual.

RATING

The item is for setting a new rating level of the Parental Control.

1. Select the PASSWORD item and then press the > button to enter it, then input

the password mentioned above, and then press the OK button to unlock the

setting of the rating level of the Parental Control.

2. Select the RATING item and then press the > button to enter it, then use the

direction buttons to select your desired rating level, then press the OK button

to confirm.

3. Select the PASSWORD item again and then press the > button to enter it, then

input the password, and then press the OK button to lock the new setting of

the rating level of the Parental Control.

DEFAULT

This item is for making all setup items change back to original status.

25

3. During JPEG playback, press one of the >/</^/v buttons to change the angle of

viewing picture that is displaying as follows:

>: 90 deg cw; <: 90deg ccw; ^:UP<-->DOWN; v: LEFT<-->RIGHT

During JPEG playback, press the PROG button to change the mode of refresh picture.

During JPEG playback, press the STOP button to stop playing and return to the root

menu.

* During JPEG playback, the following buttons are not available: SLOW-FWD,

SUBTITLE, TITLE, ANGLE, STEP, AUDIO, RDM and A-B.

* In JPEG mode,the other operations are same as ones in MP3/WMA mode.

5.14 MP4 Operation

1. The root menu is displayed on TV when beginning to switch on DISC mode, then it will

automatically play the first file.

During playback, press the STOP button to stop playing and return to the root menu.

2. When displaying the root menu, press the direction buttons to select your desired

FOLDER or file, then press the OK or PLAY button to open the FOLDER, or play the

selected file.

When displaying the root menu, you can also use the number buttons to select the

serial number of the file and play the file.

* The ANGLE, PROG, RDM, and TITLE/PBC button are not valid.

* The other functions are same as ones in DVD disc; but the RPT function is same as

one in MP3/WMA.

5.15 ESP and ID3 Function

There is ESP function for all formats of discs.

In MP3/WMA mode, during playback, the information of the file name, folder name,

song s title, artist and album will be scrolling on the LCD display. As long as the

current playing MP3 music contains relevant ID3 tag information in version 1.0/2.0

format, the 3 items underlined above will be scrolling on the LCD display; otherwise,

they will not.

5.16 USB Operation

Power on the DVD player, then insert the USB storage, then the monitor will display

the root menu of the USB storage

This device support picture(JPG format),audio(MP3 or WMA format) and Video(MP4 format),

all the operations are same as ones of the corresponding format.

Note:The USB input with charging function ( not all products can be charged from the unit)

1.7 Wiring Diagram

10

The Description of the Wiring Diagram for Socket 1 and Socket 2

WIRING CONNECTIONG SOCKET 1

WIRING HARNESS PLUG 1

WIRING CONNECTIONG SOCKET 2

WIRING HARNESS PLUG 2

5.17 The DVD System Menu Setup Operation

1. Press the SETUP button on the remote controller to access the DVD System Menu on

the monitor.

2. There are 6 setup pages in all for the System Menu. Press the > or < button to select

an desired setup page.

3. Press the ^ or v button to select an setup item in the selected setup page.

4. Press the > button to enter the setup item. Then press the v or ^ button to select a

desired mode of the setup item, finally press the OK button to confirm it.

* Press the < button to return to the upper level.

* Press the SETUP button again or use the direction buttons to highlight the item of the

EXIT SETUP and then press the OK button to exit the System Menu.

11

WIRING CONNECTIONG SOCKET 1 VIEW

PURPLE

PURPLE

ACCESSORY

5.12 Program Playback

It allows you to enter the order in which you want some chapters/tracks in

DVD/VCD/MP3/WMA/CD disc to play.

1 During playback, press the PROG button to enter a program interface as

follows:

for DVD discs for VCD/MP3/WMA/CD discs

24

WIRING CONNECTIONG SOCKET 2 VIEW

2

3

PIN NO

1

2

3

4

COLOR

BLUE

BLUE/BLACK

ORANGE

FUNCTION

RIGHT(C)SPEAKER (+)

RIGHT(C)SPEAKER (-)

LEFT(C)SPEAKER (+)

ORANGE/BLACK LEFT(C)SPEAKER (-)

2 Use the direction buttons to move cursor onto the desired place for inputting

the sequence number.

3 Use the number button to input desired sequence number of title/chapter/

track with desired sequence.

4 Use the direction button to move cursor onto Play item, then press the OK

button to play the programmed titles/chapters/tracks in programmed order;

only pressing the PLAY button also can play the programmed titles/chapters

/tracks in programmed order.

* To exit program playback, firstly press the STOP button, then press the PLAY

button to enter sequence playback; or press the PROG button twice again.

* To remove the all programmed sequence numbers, move the cursor onto

Clear item, then press the OK button.

* To change the programmed sequence, move the cursor onto the item you

want to change, input the desired sequence number.

* During VCD playback, if it is in PBC ON mode, at the same time of entering

the state of program playback, it turns off PBC mode.

5.13 Playback the Picture CD in JPEG Format

1. The root menu is displayed on the monitor when beginning to switch on DISC

mode. At the time, it plays MP3/WMA file.(the TITLE or MENU button is not

available).

In the root menu, the left file sort icon is for MP3/WMA file; the middle file sort

icon is for JPEG file; the right file sort icon is for VIDEO file. If one of these 3

file sort does not exist, you can not move cursor onto the file sort icon.

2. When displaying the root menu, press the direction buttons to select your

desired FOLDER, file or file sort icon, then press the OK or PLAY button to

open the FOLDER, or play the selected file, or play only this sort of file.

When displaying the root menu, you can also use the number buttons to

select the serial number of the file and play the file.

When you select a JPEG file sort icon, press the ^ or > button to select the

first JPEG file, then press the v button to select the desired JPEG file, finally

press the OK or PLAY/PAUSE button to display the JPEG picture in full screen

from the selected JPEG picture.

23

ZOOMx2,ZOOMx3,ZOOMx4,ZOOMx1/2,ZOOMx1/3,ZOOMx1/4,ZOOM OFF.

Press one of the ^/v/>/< buttons to select the area you want to enlarge.

5.9 Change the Caption Language

When playing DVD discs, press the SUBTITLE button repeatedly to select

the language of the caption or turn off the caption.(depend on the disc used.)

When playing VCD/MP3/WMA/CD discs, the button is not available.

5.10 Change the Audio Language

1. When playing DVD discs, press the AUDIO button repeatedly on the IR

remote control to select the desired language type(depend on the disc used)

2. When playing VCD discs, press the AUDIO button repeatedly to select the

sound mode of the MONO L, MONO R, and Stereo, no language function.

3. When playing CD/WMA/MP3 discs, the AUDIO button is invalid.

5.11 Look over the Playback Status

1. When playing DVD discs, press the OSD button repeatedly on the remote

control to turn on/off the playback status. When it is on, it will display the

information such as: the serial number of the playing title, the serial number

of the playing chapter, the elapsed time of the playing chapter, the remaining

time of the playing chapter, the elapsed time of the playing title, the remaining

time of the playing title, etc.

2. When playing VCD/CD discs, press the OSD button repeatedly on the remote

control to turn on/off the playback status. When it is on, it will display the

information such as: the serial number of the playing track, the elapsed time

of the playing track, the remaining time of the playing track, the elapsted time

of the disc, the remaining time of the disc.

WIRES FROM RV,BOAT OR TRUCK

12

R IO CT NE ON EO C ER TR OM S S FR RE R WIN KE EA D SP R AN WE PO

13

1.8 Mounting Installation

Location

* Choose a mounting location away from humid areas, water sources, appliances or any equipment that can radiate heat.

* Select an area on a wall or cabinet which is free from cable, fuel or brake lines and ensure

the area behind the wall mount stereo has a vent hole or if it is an enclosed box and has

adequate room around the rear of the unit for cooling.

* Ensure when the stereo is mounted in the cut out that the wires at the rear of the unit are not

pressed against the heat sink

Mounting Opening

* Refer to following mounting hole diagram,measure and cut a mounting area.

+

5.94 0.005

MOUNTING SCREWS

M3 22

1.32 0.02

-

* Where possible leave around 1 to 2 inches of space inside the cabinet around the sides and

rear of the stereo housing to help with airflow and ventilation.

Installing the unit.

* Before finally installing the unit, connect the wiring temporarily and make sure

the unit and the system work properly.

*Fix the unit with screw according to following diagram.

PLASTIC FRAME

5.5 Playback from a specified chapter/track or a specified time

1. When playing DVD discs, press the SEARCH button to display a interface

and highlight the title item, then use the number buttons to input the serial

number of the title; use the direction buttons to highlight the chapter item,

then use the number buttons to input the serial number of the chapter; finally

press the OK or PLAY button to play the selected chapter.

2. When playing VCD/MP3/WMA/CD discs, press the SEARCH button to display

a interface and highlight the track item, then use the number buttons to input

the serial number of the track; finally press the OK or PLAY button to play the

selected track .

5.6 Playback in Random

When playing DVD/VCD(PBC OFF)/MP3/WMA/CD discs, press the RDM

button to switch between RANDOM (ON)/RANDOM OFF. When in RANDOM

(ON) mode, it will play in random.

22

5.7 Playback in Different Angle

1. When playing VCD/MP3/WMA/CD discs, the ANGLE button on the IR remote

control is not available.

2. When playing DVD discs, press the ANGLE button repeatedly on the IR

remote control to view in different angle.(This function is only for the DVD

discs with ANGLE function)

5.8 Playback in Zoom Mode

In DVD/VCD mode, during playback, press the ZOOM button continuously

to enlarge a certain area of the images on the screen with these multiples:

21

During slow forward, press the PLAY button to resume normal playback.

The function is only for video.

5.3. Playback with still frame

If the unit is currently running DVD.VCD disc,press the STEP button consecutively

to display the still frame forward with step by step.

Press the PLAY button to resume normal playback.

5.4 Playback Repeatedly

5.4.1 ONE/ALL Repeat

1. In the mode of DVD disc playback:

Press the RPT button to select REP CHAPTER, REP TITLE, REP ALL

or REP OFF.

2. In the mode of VCD(PBC OFF)/CD disc playback:

press the RPT button to select REP ONE, REP ALL or OFF.

When it is in the state of PBC ON, during VCD disc playing, the RPT

button are not available.

3. In the mode of MP3/WMA disc playback:

Press the RPT button to select REP ONE, REP DIR, REP ALL or OFF.

5.4.2 A-B Repeat

Press the A-B button if you want to repeat a specific segment on a disc

that you define:

1. Press the A-B button at a point (A) where you want it to be the start point

of the repeat segment. Press the A-B button again at a point (B) where you

want it to be the terminal point of the repeat segment. Then it will play the

segment repeatedly.

2. To cancel the A-B repeat mode and resume normal playback, press the A-B

button for the third time.

Note:

During VCD/MP3/WMA/CD playback, points A and B must be within the

same track.

During DVD playback, points A and B can be selected from different chapters.

14

2. Common Operation

1.Turning On and Off the unit

By pressing the power button will turn on or enter standby mode

Sleep Tight function

By holding the power button for 5 seconds while the unit is in standby mode will enable

Sleep Tight mode, this is were all illumination on the front panel will turn off on the unit.

2.Selecting a Source:

DVD / USB - once a DVD or USB is inserted into the unit, the unit will automatically switch

to display this source menu. Press this function button to select DVD if a disk is already

installed and the unit is playing from another source.

AM/FM - by pressing this button will scroll through the FM1, FM2, FM3, AM1, AM2.

To switch this units AM/FM reciever between USA and Europe frequencies press and hold

the AM/FM button for 10 seconds until the region is displayed on the screen.

AUX -this button allows you to scroll through the AUX inputs fitted to the strereo

AUX input - connection on the rear of the unit, (normally used to connect TV sound input)

AV IN - connection on front of unit to connect a external audio source

BLUETOOTH / DIMMER - by pressing this button will enable bluetooth connection, if the

button is held in for over 2 seconds it will then dim the face illumination by 1 of the 3 stages

each time pressed.

3.Volume Adjust

Rotate the volume knob clockwise to increase volume, rotate anticlockwise to reduce volume.

4. Mute

Press MUTE button to mute what ever source is playing and display mute on the screen.

Press the mute button again to release unit from mute.

5.

Clock and Alarm Set

1)

To display the clock on the LCD display, press Clock botton on the remote control

2) To Adjust or set the clock, press and hold the Clock Set button on the front of the

unit or hold the Clock button on the remote control until the clock set feature is

displayed on the LCD display of the stereo then use the volume knob on the unit

or + and - buttons on the remote control to adjust the time, push in the volume knob

on the stereo or press the SEL button on the remote control to change from setting

hours to minutes. Once time is set the stereo will automatically set after a few second

of not pressing any functions.

3) To set the Alarm Clock the Stereo must be in AM/FM mode when the Alarm Set

buttois held in. The alarm clock is set in the same way as above for the clock set.

Once the alarm clock is set, you will see the ALARM light illuminated under the LCD

display.

Press the alarm on /off button to turn on or cancel the alarm setting.

15

6. To select a preset EQ mode

Press the EQ button to select the preset music equalizer curves: MOVIE,

MUSIC, CLASSIC, CONCERT .The sound effect will be changed.

7. To turn on/off LOUD mode

Press and hold LOUD button on the front panel to turn on/off LOUD

mode.

8.To adjust the sound equalizer curves

To adjust the sound equalizer curves, briefly and repeatedly press the SEL

button to select the sound equalizer curves of VOL, BAS(without preset EQ),

TRE (without preset EQ), BAL, FAD,BEEP(ON/OFF), then rotate the VOL knob

on the front panel or press the + or - button to adjust level.

9.To preset the unit to sleep mode

Press the SLEEP SET button to select the time you want to make the unit go

sleep mode in. There are four modes for select.

00: The sleep mode off

15: The NDICATOR light SLEEP will be lighted, The unit will go to sleep mode

in 15 minutes

30: The INDICATOR light SLEEP will be lighted, The unit will go to sleep mode

in 30 minutes

60: The INDICATOR light SLEEP will be lighted, The unit will go to sleep mode

in 60 minutes

NOTE: Only the ALARM ON mode is selected, the above preset function

can effect.

10.To preset the unit from sleep mode to turning on

Press and hold the SLEEP SET to pop up the preset clock interface. adjust the

time you want the unit to turn on in.

NOTE: Only the ALARM ON mode is selected, the above preset function

can effect.

11.ALARM ON OFF BUTTON

Press the ALARM ON OFF BUTTON to select the ALARM ON or ALARM OFF

mode.

ALARM ON: The INDICATOR light ALARM will be on.

ALARM OFF:The INDICATOR light ALARM will be off.

12.ZONE A/B/C BUTTON

Pressing zone A, B or C buttons will turn on or off the audio source in each of

the different areas which your speakers are connected. A blue indication light

with A, B and C is displayed under the LCD display and when lit is to indicate

when sound is being fed to the Zone.

13.Press the button or TITLE button up to the previous menu.

14.To reset the unit

when the display is incorrect, or the function buttons are not effective or

sound is distorted, then use a sharp point to press the RESET button, that

will make the unit be reset to factory default and re-instate the correct functions .

20

In VCD mode

1. When starting to turn on the PBC function, it will play from the beginning of

the disc till it display the PBC menu on TV screen if the disc include the PBC

menu.

2. Press the number buttons to select your desired track to play.

In MP3/WMA mode

1. The root menu is displayed on the monitor screen all the time(and the TITLE

or MENU button is not available).

2. Press the direction buttons to select your desired FOLDER, then press the

OK or PLAY button to open the FOLDER, and then press the direction buttons

to select your desired file, finally press the OK button to play the selected file.

In CD mode, the TITLE, PBC, MENU buttons are disabled.

4.7 Terminate the Playback

1. Press the EJECT button to eject disc.

2. Press and hold the POWER button on the front panel or briefly press the

POWER button on the remote controller to turn off the DVD player.

5 . Advanced Disc, USB Operation

5.1 Playback with Speed

During normal playback, Rotate the TUN/TRK to the right or left limit position

stopping for about 1 second or press and hold the >>|/|<< button on the remote

controller continuously to fast forwards or backwards at the following

speeds: x2, x4, x8,x16, x20, normal.

During speed playback, press the PLAY button to resume normal playback.

5.2 Playback with Slow Speed

During playback , press the SLOW_FWD button to execute the Slow

Forward function.

With each consecutive pressing of the SLOW_FWD button, the playback

speed decreases. The speed levels in Slow Forward as follows:

x1/2,,x1/3,x1/4,x1/5,x1/6,1/7,normal.

19

4.2 Pause Playback

When playing DVD/VCD/CD/MP4/MP3/WMA discs, press the PAUSE/PLAY

button on the front panel or remote control to pause the playback, press the

PAUSE/PLAY button again to resume normal playback.

4.3 Stop Playback

When playing DVD/VCD/MP3/WMA/CD discs, press the STOP button once to

pause the playback, then press the PLAY button to resume the normal playback;

press the STOP button twice to stop the playback, then press the PLAY button

to start playback from the beginning of the first chapter/track.

4.4 Select Chapter/Track with the TUN/TRK KNOB or the >>| / |<< Button

Rotate the TUN/TRK KNOB on the front panel or the >>| / |<< button on the

remote control during playback to select the next or last chapter/track to

playback.

Note: Rotate the TUN/TRK KNOB or press the >>|/|<< button multiple times to

advance multiple chapters/tracks forward or backward.

4.5 Select Chapter/Track with the Number Buttons

When playing DVD/VCD(PBC OFF)/MP3/WMA/CD discs, press one of the

1~9 and the 0/TA number buttons to directly select and play the 1st to 10th track /

chapter (the 0/TA button is used as the 10 button).

If you want to play the track/chapter with serial number bigger than 10,

use the 10+, 1~9 and 0/TA button. For example 1, to play the 13th track/

chapter, firstly press the 10+ button once, then press the 3 button. For

example 2, to play the 34th track/chapter, firstly press the 10+ button for 3

times, then press the 4 button.(the 0/TA button is used as the 0 button)

Note: pressing and holding the +10 or -10 buttons will allow you to play the next

10 or last 10 chapter/track(only for MP3/WMA).

4.6 Select Chapter/Track with the Root/PBC Menu (If the disc includes the

root/PBC menu)

When playing DVD discs:

1. Press the TITLE button on the remote control to display the title list.

2. Press the direction buttons to select your desired title, and then press the OK

or PLAY button to open the root menu of the selected title.

3. Press the direction buttons to select your desired chapter, finally press the

OK or PLAY button to play the selected chapter.

During playback, pressing the TITLE button on front panel or long pressing the

TITLE button on the remote can directly displaythe root menu of the title that is

playing.

16

3. Radio Operation

1. FREQUENCY SELECT

In RADIO mode. Press and hold the AM/FM button to select your desired frequency EUROPE,

USA1 or USA2.

2. AM/FM BUTTON

In RADIO mode, press the AM/FM button to select your desired radio band of FM1, FM2, FM3,

AM1, AM2 , and the selected band will be displayed on the small monitor of the front panel.

3. TUNE/SEEK UP/DOWN

In RADIO mode:

1) Rotate the TUN/TRK KNOB to the right or left limit position stopping for about 1 second or Press

and hold the >>|/ |<< button on the remote control to automatically search up/down for a available

station from the current frequency.

2) Rotate the TUN/TRK KNOB or the press the >>| / |<< button on the remote control

to manually search up or down with step by step for your desired station from the current

frequency.

4. AS/PS BUTTON

In RADIO mode:

1) When pressing and holding the AS/PS button on the front panel or APS button on the remote

control, the radio searches from the lowest frequency and checks the signal strength level until 1

cycle search is finished. And then the 6 strongest stations are preset to the corresponding preset

number memory bank. The AS operation is implemented in each bank of the selected band.

When the AS operation is finished, it will resume broadcasting

on the M1.(It can store 3x6 stations for FM and 2x6 stations for AM in all)

2) When briefly pressing the AS/PS button on the front panel or APS button on the remote control,

the radio searches for each preset station from the M1. When the field strength level is more than

the threshold level of the stop level, the radio holds at that preset number for a few seconds with

releasing mute, and then searches again. After finishing a circle of searching, it will stop

searching on the M1.

NOTE: In FM band, FM1,FM2,FM3 is checked one at a time.

In AM band, AM1, AM2 is checked one at a time.

5. PRESET STATION [ 1-6 ] BUTTONS

In RADIO mode:

1) To memorize the current frequency on the current band, press and hold any one of the six preset

buttons (1-6) .

2) To recall the preset memory on the current band, press one of the preset buttons [1-6] .

6. STEREO/MONO BUTTON

Press the ST button to select the STEREO or MONO sound mode for

FM band.

7. LOC BUTTON

1) In RADIO mode, when the signal of the distance radio station are very weak and the receiving

effect is bad during tuning, check whether there is the word LOC on LCD. If there is the word

LOC on LCD, press this button to turn off the LOC function, then tune again for the distance

radio station;

2) In RADIO mode, when the signals from the local radio stations are too strong, this could lead

to interference. press this button to turn on the LOC function, and the LOC icon will be lit up on

the LCD. Re-tune for the local station required.

17

8. PTY (PROGRAM TYPE) BUTTON

Long press the SEL button on the front panel or press the PTY button on remote

shortly to select one of the following mode.

When PTY group is on, press the VOL+ or VOL- button on the remote

controller or rotate the VOL knob on the front panel to select one of PTY

programs: <-->NEWS<-->AFFAIRS<-->INFO<-->SPORT<-->EDUCATE

<-->DRAMA<-->CULTURE <-->SCIENCE<--> VARIED<-->WEATHER<-->

FINANCE<-->CHILDREN<-->SOCIAL<-->RELIGION<-->PHONE IN<-->

TRAVEL<-->LEISURE<-->DOCUMENT< -->PTY NONE<-->POP M< -->

ROCK M<-->EASY M<-->LIGHT M<--> CLASSICS<-->OTHER M<-->

JAZZ<-->COUNTRY<-->NATION M<-->OLDIES<-->FOLK M<-->

When PTY group is on, pressing the 6 number buttons also can select one of

PTY programs as above.

After selecting one of the PTY programs, it will display SEEK PTY and

automatically search for the station of the PTY program. If the station of

the PTY program does not exist, it will display PTY NONE and then return

back to the normal station.

Note: Press and hold the SPEAKER SELECTION BUTTON B on the front panel for

5 seconds can turn on/off RDS mode.

9. AF [ALTERNATIVE FREQUENCIES] BUTTON

Long press the SEL button on the front panel or press the AF button on the

remot control briefly, the AF switchingmode is selected and the state of the AF

switching mode is displayed by AF segment.

Segment off: AF switching mode off.

Segment on: AF switching mode on, and has RDS information.

Segment flashing: AF switching mode on, but RDS information is not received yet.

When the AF switching mode is selected, the radio checks the signal strength

of the AF all the time. The interval of checking time of each AFs depends on

the signal strength of the current station, from a few minute for the strong

station to a few seconds for the weak station. Every time that a new AF is

stronger than the current station, it switches over to that frequency for very

short time, and the NEW FREQUENCY is displayed for 1-2 second. Because

the mute time of the AF switching or the checking time is very short, it is

almost inaudible in case of normal program. (When AF flash on LCD, it will

search for the stronger RDS station. If AF and TP flash on LCD, it can only

search for the traffic announcement station).

In FM mode, when AF is on, SEEK, (SCAN), AUTO-MEMORY function can

only receive and save the RDS program.

10. TA [TRAFFIC ANNOUNCEMENT] BUTTON

Long press SEL button on the front panel then rotate it or press the TA button

on remote shortly to turn on TA search mode.

When traffic announcement is transmitted:

1).If the unit is in Disc Play mode, it will switch to radio mode temporarily.

2).Temporarily switch over to an EON linked station when EON detects a

traffic announcement on that other program, and TA, TP will be displayed

on LCD

* TA interruption function:

The current traffic announcement is cancelled by pressing TA button shortly.

* When TA is on, SEEK, (SCAN), AUTO MEMORY function can be received

or saved only when traffic program identification code has been received.

18

4 Basic Disc, USB Operation

4.1 Begin playback

1. Press the POWER button briefly to turn on the DVD player.

After turning on the DVD player, please turn on the monitor, and ensure that

the video output of the monitor is the video input from the DVD player

connected with the monitor.

? Common Question

Q: There is not anything is displayed on TV screen when the DVD player is

turned on. How to solve the problem?

A: Ensure that the TV was set to right video input(not TV channel); for

example, if you make VIDEO1 INPUT of TV and DVD player connected

with each other, then you need set TV to VIDEO1.

2 . Insert a disc into the DISC SLOT(Label surface up).

! NOTE

1. For some discs that are seriously scratched or poor manufacturing or

recording quality, it may not play.

2. If the player can not read disc under normal condition, please try to

eject and reload the disc again.

3. Remark:

1) In addition to normal CD and DVD, this unit supports to play CD-R,

CD-R/W, DVD-R and DVD-R/W as well; however, depending on the

conditions of the recording equipment, recording program or the disc

itself, some CD-R, CD-R/W, DVD-R or DVD-R/W may not play.

2) When dealing with CD-R, CD-R/W, DVD-R or DVD-R/W recording,

too high recording speed may result in poor signal quality and therefore,

it is recommendable to select as lower as possible recording speed.