System Requirements

System Requirements

• A computer with an available 32-bit PCI bus master slot operating at 33MHz

• Windows ® 2000, 2003, 2008, XP, Vista ® , 7, Linux 2.4.x and above, or Mac OS 10.2.x and above

• 150MHz processor and at least 32MB of RAM

• 32MB free hard drive space

• CD-ROM Drive

Package Contents

• D-Link DGE-530T Ethernet Desktop Adapter

• Manual and Software on CD

• Standard and Low Profile Brackets

• Quick Install Guide

If any of the above items are missing, please contact your reseller.

D-Link DGE-530T Quick Install Guide 2

System Requirements

Package Contents

Installation

Installation

Note: Install the drivers before installing the adapter into your computer.

Turn on your computer and Insert the D-Link DGE-530T Driver CD in the CD-ROM drive. The step-by-step instructions that follow are shown in Windows ® XP. The steps and screens are similar for the other Windows operating systems.

If the CD Autorun function does not automatically start on your computer, go to Start > Run . In the run command box type

“ D:\DGE530T.exe

” (where D: represents the drive letter of your

CD-ROM drive).

Drivers for non-Windows operating systems are located on the

D-Link CD.

When the autorun screen appears, click Install Drivers (this will launch the Network Utility program and install the drivers) . An

Installation Wizard will guide you through the process, no matter which operating you are running. Your DGE-530T will be installed successfully in just a few moments, allowing you to enjoy the many advantages of joining an Ethernet LAN.

If any of the above items are missing, please contact your reseller.

2 3 D-Link DGE-530T Quick Install Guide

Installation

Once the installation is complete, click OK to finish.

Shut down your computer. Go to Start > Shut Down > select Shut

Down and click OK .

Once your computer is turned off, remove the power cable from the computer. Open the case and insert the D-Link adapter into an available PCI slot.

Note: Write down the serial number and hardware revision (e.g. B1) before installing the adapter. If you contact technical support, you will need this information.

Replace the case, plug in the power cable, and power on your computer.

D-Link DGE-530T Quick Install Guide 4

Installation

Once you boot your computer, Windows ® will automatically install the drivers.

Windows XP users: You will receive a bubble stating that Windows found the DGE-530T adapter.

Windows ® 7/Vista ® users: You will receive a bubble stating Windows has finished installing the DGE-530T adapter.

4 5 D-Link DGE-530T Quick Install Guide

Verify Installation

Verify Installation

To verify that the drivers are installed, you may view Device Manager.

To view the device manager, please follow the steps below:

Step 1:

Windows ® 2000: Click on Start > Settings > Control Panel

Windows XP: Click on Start > Control Panel

Windows ® 7/Vista ® : Click on Start > Control Panel

Step 2:

Windows ® 2000/XP: Click on the System icon. Click the Hardware tab and then click Device Manager.

Windows Vista ® : Click on the System and Maintenance icon and then click on Device Manager.

Windows 7 ® : Click on the System and Security icon and then click on Device Manager under System.

Step 3:

Scroll down and click the plus (+) sign next to Network Adapters. The

D-Link DGE-530T Gigabit Ethernet Adapter (rev.B) will be listed.

Configure your Adapter

D-Link DGE-530T Quick Install Guide 6

Configure your Adapter

Configure your Adapter

After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server

(i.e router) automatically. To verify your IP address, please see the following steps below.

Windows ® 2000/2003/XP: Click on Start > Run . In the run box type cmd and click OK .

Windows ® 7/Vista ® : Click on Start > All Programs > Accessories

> Command Prompt .

At the prompt, type ipconfig and press Enter .

This will display the IP address, subnet mask, and the default gateway of your adapter.

6

If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your router. Some firewall software programs may block a DHCP request on newly installed adapters.

7 D-Link DGE-530T Quick Install Guide

Configure your Adapter

If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below.

Step 1:

Windows ® 2000: Click on Start > Settings > Control Panel >

Network Connections

Windows ® XP: Click on Start > Control Panel > Network

Connections

Windows Vista ® : Click on Start > Control Panel > Network and

Internet > Network and Sharing Center > Manage network connections

Windows ® 7: Click on Start > Control Panel > Network and Internet

> Network and Sharing Center > Change Adapter Settings

Step 2:

Right-click on the Local Area Connection, which represents your

D-Link network adapter, and select Properties .

Step 3:

Highlight Internet Protocol (TCP/IP) and click Properties .

Step 4:

Click Use the following IP address and enter an IP address that is on the same subnet as your network or the LAN IP address on your router.

Example: If the router’s LAN IP address is 192.168.0.1, make your

IP address 192.168.0.X where X is a number between 2 and 99.

Make sure that the number you choose is not in use on the network.

Set Default Gateway the same as the LAN IP address of your router

(192.168.0.1).

D-Link DGE-530T Quick Install Guide 8

Configure your Adapter

Set Primary DNS the same as the LAN IP address of your router

(192.168.0.1). The Secondary DNS is not needed or you may enter a DNS server from your ISP.

8

Step 5:

Click OK twice to save your settings.

9 D-Link DGE-530T Quick Install Guide

Notes

Notes

D-Link DGE-530T Quick Install Guide 10

Notes

Notes

10 11 D-Link DGE-530T Quick Install Guide

Technical Support

D-Link’s website contains the latest user documentation and software updates for D-Link products.

U.S. and Canadian customers can contact D-Link Technical Support through our website or by phone.

United States

Telephone

(877) 453-5465

World Wide Web http://support.dlink.com

Canada

Telephone

(800) 361-5265

World Wide Web http://support.dlink.ca

Version 2.6

March 12, 2010

6DGE530TQB04G

Copyright ©2009-2010 D-Link Corporation/D-Link Systems, Inc. All rights reserved. D-Link and the D-Link logo are registered trademarks of D-Link Corporation or its subsidiaries in the United States and other countries. Other trademarks are the property of their respective owners.

D-Link DGE-530T Quick Install Guide 12