PNI PMR R11V User Manual

Statie radio UHF portabila

PNI PMR R11V

MANUAL DE UTILIZARE

Cuprins:

Ÿ Introducere ... 1

Ÿ

Ÿ

Ÿ

Ÿ

Ÿ

Caracteristici principale ... 1

Distanta de lucru ... 1

Atentionari speciale ... 2

Descriere dispozitiv ... 2

Incarcarea acumulatorului ... 2

Ÿ

Ÿ

Ÿ

Ÿ

Instalarea accesoriilor ... 3

Descriere comenzi si functii ... 5

Programare functii taste ... 6

Specificatii tehnice ... 7

1. INTRODUCERE:

PNI PMR R11V este o statie radio portabila care se poate folosi gratuit in majoritatea tarilor din Europa.

PNI PMR R11V este solutia ideala pentru profesionistii care vor sa fie in contact cu colegii (constructii, cladiri, hoteluri, show-uri televizate) sau cu cei apropiati (prietenii si familia) in timpul liber.

Cu ajutorul software-ului de programare dedicat, PNI PMR R11V ofera posibilitatea adaptarii performantei statiei radio la nevoile fiecarui utilizator, prin activarea / dezactivarea unor functii (SCAN, TOT, BCL etc.). Pentru informatii suplimentare, va rugam sa consultati manualul de programare.

2. CARACTERISTICI PRINCIPALE:

- Frecventa 446.00625 – 446.09375 MHz

- Putere 500 mW

- Functii principale: Scanare, Squelch, Monitorizare, Roger beep, VOX

- Economizor automat de energie

3. DISTANTA DE LUCRU:

Distanta maxima de acoperire depinde de obstacole si este obtinuta atunci cand statia este folosita in camp deschis. Distanta maxima este limitata de factori cum ar fi copaci sau cladiri. In interiorul unei masini sau a unei constructii metalice, distanta este redusa simtitor.

Distanta de acoperire pentru statia PNI PMR R11V este pana la 7 km.

1

4. ATENTIONARI SPECIALE:

- Pentru a nu deteriora statia radio, nu folositi statia fara o antena corespunzatoare

- Pentru reparatii, adresati-va doar unui service specializat

- Inchideti statia daca va aflati intr-o benzinarie

- Nu expuneti statia la soare si nu o lasati in apropierea corpurilor de incalzire

- Daca observati ca din statie iese fum sau miros, inchideti imediat statia radio si duceti-o la un centru service sau la distribuitor

- Pentru a nu deteriora statia, nu emiteti timp prea indelungat

- Inchideti statia daca va aflati intr-un mediu cu substante inflamabile sau explozive

5. DESCRIERE DISPOZITIV:

Accesorii:

ANTENA ACUMULATOR INCARCATOR CLEMA CUREA SNUR

6. INCARCAREA ACUMULATORULUI:

Inainte de prima utilizare, incarcati acumulatorul. Incarcati si descarcati acumulatorul de

2-3 ori pentru a obtine capacitatea maxima a acestuia.

Atentionari:

- Folositi doar acumulatorul original

- Nu scurtcircuitati terminalele acumulatorului

- Nu incercati sa deschideti carcasa acumulatorului

- In timp ce incarcati acumulatorul, temperatura ambientala trebuie sa fie intre 0 si 40°C

- Inchideti statia radio in timp ce incarcati acumulatorul

- Nu intrerupeti alimentarea in timpul incarcarii acumulatorului

- Inlocuiti acumulatorul daca observati ca i-a scazut considerabil durata de functionare

- Incarcati acumulatorul doar cand acesta este complet descarcat

Operatiuni de incarcare:

NOTE: Daca acumulatorul este descarcat, va rugam sa-l incarcati.

Urmariti indicatorul LED de pe incarcator pentru a afla nivelul de incarcare al bateriei:

- LED rosu - acumulatorul se incarca

- LED verde - acumulatorul este complet incarcat

1. Alimentati incarcatorul la o sursa de curent cu ajutorul adaptorului inclus

2. Introduceti acumulatorul sau direct statia radio cu acumulatorul instalat in incarcator

3. LED-ul incarcatorului se aprinde

4. Daca acumulatorul s-a incarcat complet, LED-ul de pe incarcator va deveni verde.

Durata de incarcare completa a acumulatorului este de aproximativ 3 ore. Dupa incarcare, scoateti acumulatorul sau statia radio cu acumulator din incarcator.

NOTA: Asigurati-va ca acumulatorul face contact cu incarcatorul. Daca LED-ul clipeste, inseamna ca acumulatorul este deteriorat sau ca temperatura ambientala este in afara intervalului recomandat.

2

7. INSTALAREA ACCESORIILOR:

Instalarea acumulatorului

Pozitionati acumulatorul pe statie ca in imaginea de mai jos. Apasati usor in jos, pana cand auziti un click. (Imaginea 1)

Pentru a scoate acumulatorul, apasati pe butonul de siguranta al acestuia, in timp ce trageti in sus. (Imaginea 2)

Imaginea 1 Imaginea 2

Instalarea antenei:

Pentru a monta antena, pozitionati-o in mod corect pe statia radio si rotiti in sensul acelor de ceasornic. (Imaginea 3)

Pentru a scoate antena, rotiti-o in sens invers acelor de ceasonic. (Imaginea 4)

Imaginea 3

3

Imaginea 4

Instalarea clemei pentru curea si conectarea castilor:

Fixati clema pentru curea folosind suruburile din pachet. (Imaginea 5)

Pentru a conecta o pereche de casti, indepartati protectia de cauciuc si conectati mufa castilor. (Imaginea 6)

Imaginea 5 Imaginea 6

Instalarea snurului pentru incheietura:

Fixati snurul pentru incheietura mainii ca in imaginea de mai jos. (Imaginea 7)

Imaginea 7

4

8. DESCRIERE COMENZI SI FUNCTII:

Antena

LED indicator:

LED Rosu - emisie

LED verde - receptie

Difuzor

R11V

Selector canale:

Rotiti pentru a schimba canalele (1 - 16)

Buton inchis/deschis

Volum:

Rotiti in sensul acelor de ceasornic pentru a deschide statia

Microfon

Buton PTT:

Apasati pentru a emite

Tasta 1

Tasta 2

Mufa microfon/ difuzor extern

NOTE:

Tastele 1 si 2 sunt programabile de pe calculator.

Apasati simultan tastele 1 si 2 pentru a activa functia apel de urgenta.

5

9. PROGRAMARE FUNCTII TASTE:

Tastele 1 si 2 pot fi programate cu ajutorul software-ului dedicat cu urmatoarele functii:

- MONITOR

- SCAN ON / OFF

- SCAN TEMPORARY DELETE

-

TALK AROUND

- REVERSE FREQUENCY

- VOX ON / OFF

M

ONITOR

:

Functia Monitor permite dezactivarea temporara a squelch-ului pentru a receptiona eventuale semnale extrem de slabe. Apasati scurt tasta 1 pentru a activa functia Monitor.

S

CAN

:

Tineti apasat tasta 2 pentru aproximativ 4 secunde, pentru a putea activa functia de scanare. Statia va scana toate canalele pornind de la canalul in uz. Ori de cate ori este detectat un semnal, statia va opri scanarea. Pentru a relua scanarea apasati butonul

PTT.

V OX :

Functia VOX permite conversatia de tip hands-free (fara maini). Trebuie doar sa vorbiti in directia microfonului si comunicarea va fi in mod automat activata.

Sensibilitatea VOX poate fi setata pe 10 nivele (0 - 9) prin software-ul de programare.

Nivelul 0 arata ca functia VOX este oprita, 1 reprezinta cel mai mic nivel de sensibilitate

VOX iar 9 cel mai inalt nivel.

S QUELCH :

Functia Squelch suprima zgomotele de fundal de pe canalale radio, permitand receptionarea semnalelor slabe.

R11V are 10 nivele diferite de squelch care pot fi setate prin software-ul de programare.

Nivelul 0 arata ca functia squelch este oprita. De la nivelul 1 pana la nivelul 9 veti avea diferite nivele de reducere al zgomotului.

Asigurati-va ca nu setati un nivel excesiv de ridicat al Squelch-ului pentru ca altfel nu veti mai putea primi semnalele slabe.

R OGER B EEP

Atunci cand butonul PTT este eliberat, statia va emite un beep pentru a confirma altor utilizatori ca ati incheiat transmisia si ca pot incepe sa vorbeasca.

B EEP TONE :

Aceasta functie permite producerea unui beep de fiecare data cand apasati un buton.

6

10. SPECIFICATII TEHNICE:

Functii:

- Monitor

- Scan

- Scan temporary delete

- Talk Around

- Frecventa inversata

- Vox

- BCL (Busy Channel Lockout - Blocare canal ocupat)

- Codare DTMF ANI

- Squelch programabil (9 nivele)

- TOT (Time Out Timer) 0 - 270 secunde

- Economisire baterie

- Roger Beep

- Taste programabile

- Apel de urgenta

Generale:

Ÿ

Ÿ

Gama de frecventa 446.00625 – 446.09375 MHz

16 canale

Ÿ

Ÿ

Ÿ

Ÿ

Ÿ

Ÿ

Alimentare 7.4V DC

50 coduri CTCSS / 105 coduri DCS

Impedanta antena 50 Ohmi

Temperatura de operare -20 ~ +50°C

Dimensiuni 114 x 59 x 34 mm (fara antena)

Greutate 190 g (baterie inclusa)

Emisie:

Ÿ Stabilitate frecventa ±2.5PPM

Ÿ

Ÿ

Ÿ

Ÿ

Putere de emisie 500mW

Deviatie maxima frecventa ≤5KHz / 2.5KHz

Distorsiune audio ≤3%

Modulatie +3dB ~ -3dB

Ÿ

Ÿ

Putere canal adiacent ≥65dB

Latime de banda ≤16KHz

Receptie:

Ÿ Sensibilitate RF <0.2µV

Ÿ

Ÿ

Ÿ

Distorsiune audio ≤3%

Raspuns audio +2dB ~ -10dB

Selectivitate canal adiacent ≥60dB

Accesorii:

Ÿ

Ÿ

Antena

Acumulator 1600mAh Li-Ion

Ÿ

Ÿ

Ÿ

Incarcator + adaptor

Snur pentru incheietura mainii

Clema pentru curea

7

Portable UHF transceiver

PNI PMR R11V

USER MANUAL

Index:

Ÿ Introduction ... 1

Ÿ

Ÿ

Ÿ

Ÿ

Ÿ

Main features ... 1

Working coverage ... 1

Cautions ... 2

Device description ... 2

Charging the battery ... 2

Ÿ

Ÿ

Ÿ

Ÿ

Installing the accesories ... 3

Operations and functions ... 5

Key programming ... 6

Technical specifications ... 7

1. INTRODUCTION

PNI PMR R11V is a portable transceiver that is free use in almost all European countries.

PNI PMR R11V is the ideal and effective solution for the professionals who need to stay in touch with the working team (in construction sites, buildings, shows, trade fairs or hotels) or for leisure users that just want to keep up with friends and family.

Thanks to the programming software specifically made, it is possible to increase the performance of your radio or to reduce its functionality by disabling some of the default features (SCAN, TOT, BCL etc.).For further information, please consult the

Programming software manual.

2. MAIN FEATURES:

- Frequency 446.00625 – 446.09375 MHz

- Power 500 mW

- Main functions: Scan, Squelch, Monitor, Roger beep, VOX, Energy saving

3. COVERAGE:

The maximum coverage

The maximum coverage distance depends on obstacles and is obtained when the radio is used in the open field. The maximum distance is limited by factors such as trees or buildings. Inside a car or a metallic constructions, the distance is reduced significantly.

The coverage distance for PNI PMR R11V is up to 7 km.

4. CAUTIONS:

- Do not operate this radio without a proper antenna attached

- Refer service to qualified technicians only

- Turn the radio off while parked in a gasoline service station

- lf it appears that the radio diffuses peculiar smell or smoke, please shut off its power immediately, then contact with the nearest dealer.

- Don't keep the radio transmitting too long .lt may be too hot to hurt body or damage the radio itself.

- Please tum off the radio before entering the inflammable and explosive environment

5. DESCRIERE DISPOZITIV:

Accesorii:

ANTENNA BATTERY CHARGER BELT CLIP WRIST STRAP

6. CHARGING THE BATTERY:

The battery pack is not charged at the factory; charge it before use. After repeating the charge/discharge cycle two or three times, the capacity will increase to best status. You should charge or change the battery pack if the battery's power is weak.

Caution

- Use the original battery pack only

- Don't short-circuit the terminals or put it in fire.

- Don't attempt to open the unit.

- The ambient temperature should be between O"C to 40°C while charging is in progress

- Always switch OFF the transceiver equipped with a battery pack before charging

- Don't cut off the power or take off the battery during the charging process

- The battery pack life is over when its operating time decreases even though it is fully and correctly charged. Replace the battery pack.

- Don't recharge the battery pack if it is already fully charged or it will short the life of the battery.

Charging operations:

NOTE: lf the battery pack is out of power, please charge it.

The charger's indicator shows the charging status below:

- LED red- charging

- LED green- completed

1. Put the DC plug of the transformer into the DC socket of the charger unit.

2. Connected the supplied transformer to the AC jack

3. Slide the battery or the transceiver with a battery pack into the charger.

4. Make sure the battery pack contacts are in contact with the charging terminals, and the charger LED is on, it begins to charge.

5. The charger light tums to green automatically after charging is completed. After charging the supplied battery pack for 3 hours, remove it or the transceiver equipped with it from the charger.

7. INSTALLING ACCESORIES:

Installing the battery

Match the two grooves of the battery pack with the corresponding guides on the back of the transceiver then slide it. After that press the upper of the battery pack until a clicik sounds. (Img 1)

To remove the battery pack, turn off power and puii back on the release latch and slide the pack away from the transceiver. (Img 2)

Img 1 Img 2

Installing the antenna:

Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and tuming it clockwise until secure. (Img 3)

Tuming or spiraling the antenna counterclockwise to ramove the antenna. (Img 4)

Img 3

Img 4

Installing the belt clip and the speaker/microphone:

Attach the belt clip using the two supplied screws. You can unscrew it to remove the belt clip. (Img 5)

Open the cover of the speaker/microphone jack and insert the speaker/microphone plugs into the jacks castilor.(Img 6)

Img 5 Img 6

IInstalling the wrist strap:

You can install a wrist strap to the back of the transceiver. (Img 7)

Img 7

8. OPERATIONS AND FUNCTIONS:

Antenna

LED indicator: red-transmiting green- receiving

Speaker

R11V

Channel selector:

Rotate to change the channel

(1 - 16)

On/Off

Volume:

Turn clockwise to switch ON the transceiver. To switch OFF the transceiver, turn counterclockwise until a click sounds. Rotate to adjust the volume leveli.

Microphone

PTT button:

Push to talk

1 key

2 key

Speaker/microphone plug

NOTE:

Key 1 and 2 can be programmable.

ln case of emergency, you can hold on SIDE KEY 2 and SIDE KEY 3 to open the function of emergency call.

9. PROGRAMMABLE KEY FUNCTIONS:

Distributor can program the SIDE KEY 2 and SIDE KEY 3 with the functions as follow

(long press/short press):

- MONITOR

- SCAN ON / OFF

-

SCAN TEMPORARY DELETE

- TALK AROUND

- REVERSE FREQUENCY

- VOX ON / OFF

M ONITOR :

Monitor function allows to temporarily disable the squelch for receiving the very weak signals possible. Briefly press the 1 key to activate the Monitor

S CAN :

Hold down the button 2 for about 4 seconds to activate the scan function. The radio will scan all channels from the channel in use. Whenever a signal is detected, the radio will stop scanning. To resume scanning press the PTT button.

V OX :

VOX function allows hands free conversation. You just speak in the direction of the microphone and the communication will be automatically activated.

VOX sensitivity levels can be set to 10 (0-9) by software programming. Level 0 indicates that the VOX function is switched off, 1 represents the lowest level of VOX sensitivity and

9 the highest level.

S QUELCH :

Functia Squelch suprima zgomotele de fundal de pe canalale radio, permitand receptionarea semnalelor slabe.

R11V are 10 nivele diferite de squelch care pot fi setate prin software-ul de programare.

Nivelul 0 arata ca functia squelch este oprita. De la nivelul 1 pana la nivelul 9 veti avea diferite nivele de reducere al zgomotului.

Asigurati-va ca nu setati un nivel excesiv de ridicat al Squelch-ului pentru ca altfel nu veti mai putea primi semnalele slabe.

R OGER B EEP

When the PTT button is released, the radio will beep to confirm to other users that you have ended the transmission and that can begin to speak.

B EEP TONE :

This function allows producing a beep every time you press a button.

10. TECHNICAL SPECIFICATIONS:

Functions:

- Monitor

- Scan

- Scan temporary delete

- Talk Around

- Reverse frequency

- Vox

- BCL (Busy Channel Lockout)

- DTMF ANI

- Squelch programabil (9 nivele)

- TOT (Time Out Timer) 0 - 270 secunde

- Energy saving function

- Roger Beep

- Programmable keys

- Emergency call

General:

Ÿ

Ÿ

Frequency range 446.00625 – 446.09375 MHz

16 channels

Ÿ

Ÿ

Ÿ

Ÿ

Ÿ

Ÿ

Power supply 7.4V DC

50 CTCSS codes / 105 DCS codes

Impedance 50 Ohmi

Operating temperature -20 ~ +50°C

Dimensions 114 x 59 x 34 mm (without the antenna)

Weight 190 g (including the battery)

Transmitter:

Ÿ Frequency stability ±2.5PPM

Ÿ

Ÿ

Ÿ

Ÿ

Output power 500mW

Max frequency deviation ≤5KHz / 2.5KHz

Audio distorsion ≤3%

Modulation +3dB ~ -3dB

Ÿ

Ÿ

Adjacent channel power ≥65dB

Bandwidth ≤16KHz

Receiver:

Ÿ Sensitivity RF <0.2µV

Ÿ

Ÿ

Ÿ

Audio distorsiono ≤3%

Audio response +2dB ~ -10dB

Adjacent channel selectivity ≥60dB

Accesories:

Ÿ

Ÿ

Antenna

Rechargeable Li-Ion battery 1600mAh

Ÿ

Ÿ

Ÿ

Charger + adapter

Wrist strap

Belt clip

CODURI CTCSS SI DCS DISPONIBILE LA PROGRAMAREA DE PE CALCULATOR

CTCSS AND DCS CODES AVAILABLE BY PC PROGRAMMING

16

RX frequency

446.00625

446.01875

446.03125

446.04375

446.05625

446.06875

446.08125

446.09375

446.00625

446.01875

446.03125

446.04375

446.05625

446.06875

446.08125

446.09375

CH

12

13

14

15

16

8

9

10

11

6

7

4

5

1

2

3

TABELUL FRECVENTELOR

INSTALLED FREQUENCIES CHART

TX frequency

446.00625

446.01875

446.03125

446.04375

446.05625

446.06875

446.08125

446.09375

446.00625

446.01875

446.03125

446.04375

446.05625

446.06875

446.08125

446.09375

QT/DQT Dec

OFF

114.8

114.8

114.8

114.8

114.8

114.8

114.8

114.8

OFF

OFF

OFF

OFF

OFF

OFF

OFF

QT/DQT Enc

OFF

114.8

114.8

114.8

114.8

114.8

114.8

114.8

114.8

OFF

OFF

OFF

OFF

OFF

OFF

OFF

17

RESTRICTII DE UTILIZARE CONFORM DIRECTIVEI 99/05/CE

INFO ON USE RESTRICTIONS ACCORDING TO THE 99/05/CE DIRECTIVE

Country PMR446 Use restrictions and other comments

Denmark

Estonia

Finland

France

Germany

Greece

Hungary

Ireland

Austria

Belgium

Bulgaria

Croatia

Cyprus

Czech Republic

Italy and RSM

Latvia

Luthuania

Luxemburg

Malta

Netherlands

Norway

Poland

Portugal (Madeira and Azore)

Romania

Slovakia

Slovenia

Spain

Sweden

Switzerland and Lichtenstein

Turkey

United Kingdom

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Free use

Free use

Free use

Free use

Free use

Free use

Free use

Free use

Free use

Free use

Free use

Free use

Free use

CTCSS or DCS Tone Control mandatory!

Free use

Declaration of possesion, as declared in the note 101C of PNF and in dl 259 of

01/08/03

Free use

Free use

Free use

Free use

Free use

Free use

Free use

Free use

Free use

Free use

Free use

Free use

Free use

Free use

Individual license required (but license exemption is being considered) test

Reports recognised

Free use

18

19