TPF
FLUSH DIAPHRAGM PRESSURE TRANSDUCER
Main features
• Ranges: from: 0...10 to 0...1000 bar
(0...150 to 0...15000 psi)
• Accuracy: ±0.2% FSO typical
• Protection rating: IP65/IP67
• Wetted parts: 17-4PH
• Temperature range: -40...+120°C
• Flush fitting stainless steel measuring diaphragm
• Internal calibration signal
TPF Series flush diaphragm pressure transducers are based on bonded strain gauge on stainless steel technology.
Thanks to the strong flush diaphragm made with 17-4 PH stainless steel, TPF is particularly suitable for pressure measurement where the media is with high viscosity (thick fluids, oils, rubber, pulps, chemical products, etc.) and the traditional transducers with internal measuring chamber cannot be used.
The high thickness of the diapragm makes the product very reliable and suitable for heavy industrial application.
Internal state of the art electronics and very high precision mechanical machining make TPF product the ideal solution for above needs, where the non amplified mV/V sensor has to be used.
TECHNICAL DATA
Accuracy ( 1 )
Resolution
Overpressure (without degrading performance) ( 2 )
Pressure containment (Burst test) ( 3 )
Wetted parts
Body materials
Power supply
Common mode voltage
Output impedance
Load impedance
Insulation resistance
Zero offset and span setting
Output voltage (sensitivity)
Calibration signal
Long term stability
Operating temperature range (process) ( 5 )
Compensated temperature range ( 4 )
Storage temperature range
Temperature effects over compensated range (zero-span)
Mounting position effects
Humidity
Weight
Mechanical shock
Vibrations
Ingress protection
H ± 0.2% FSO typical (± 0.3% FSO max) 0-60...0-1000 bar
M ± 0.5% FSO typical (± 0.6% FSO max) 0-10...0-50 bar
Infinite
3 x Full Scale (max 2000 bar)
4 x Full Scale (max 2000 bar)
Fluid compatible with Inox 17-4PH
Inox AISI 304 Stainless Steel and Nylon 66GF35V0
10 (max 15) Vdc/ac RMS
Typical 5V @ 10V supply
350 Ω (±1)
> 1000 K
Ω
> 1000 M
Ω
@ 50Volt
± 0.5% FSO
10...40 bar / 150...500 psi - 1.5 mV/V nominal
50...160 bar / 750...1500 psi - 2 mV/V nominal
200...1000 bar / 3000...15000 psi - 3 mV/V nominal
80% FSO nominal (see connection diagram)
0.2% FSO/Year
-40...+120°C (-40...+248°F)
-20...+85°C (-4...+185°F)
-40...+125°C (-40...+257°F)
± 0.01% FSO/°C typical (± 0.02% FSO/°C max.) > 50 bar (750 psi)
± 0.02% FSO/°C typical (± 0.03% FSO/°C max.)
≤
50 bar (750 psi)
Negligible
Up to 100% HR non condensing
110 gr. nominal
100g/11msec, according to IEC 60068-2-27
20g max @ 10...2000Hz, according to IEC 60068-2-6
IP65/IP66/IP67
FSO = Full Scale Output (output signal at rated pressure)
1 Includes combined effects of Non-Linearity BFSL (Best Fit Straight Line), Hysteresis and Repeatability
2 tested for more than 1000 strokes with single duration < 2msec.
3 tested for more than 100 strokes with single duration < 2msec.
4 temperature outside compensated range may cause zero signal drift
5 ambient and/or electronics part temperature must not exceed 105°C
MECHANICAL DIMENSIONS - Process Connections
Dimensions: mm [inches]
Connection
M18 x 1.5
(code G )
Connection
3/4” - 16 UNF
(code L )
Connection
1/2” G male
(code M )
ATTENTION: for installation use a maximum torque force of 40Nm
Pressure range
PSI BAR
Dimension “A” (mm)
M18x1.5 (G) 3/4” (L) 1/2” (M)
150
250
300
10
16
20
25 13 13 20.5
500
30
35
40
Pressure range
PSI BAR
Dimension “A” (mm)
M18x1.5 (G) 3/4” (L) 1/2” (M)
750
1000
1500
2500
3000
5000
50
60
100
160
200
250
350
400
13.5
13.5
21
Pressure range
PSI BAR
Dimension “A” (mm)
M18x1.5 (G) 3/4” (L) 1/2” (M)
7500 500
600
10000 700
15000 1000
14.1
14.1
21.6
ELECTRICAL CONNECTION
P - 7 pole connector V - 6 pole connector F - 4/6 pole cable
Z - 4 pole connector
M12 x 1
E - 4 pole connector solenoid
M - 4 pole connector microsolenoid
ELECTRICAL CONNECTION - Connectors
P - 7 pole connector V - 6 pole connector
Z - 4 pole male connector M12 x 1
Male connector 09-127-09-07
Protection IP67
Male connector VPT02A10-6PT2
Protection IP66
E - 4 pole solenoid connector
M - 4 pole microsolenoid connector
F - 6 pole cable
Shield
2 1
3 4
Red
Black
White
Green
Blue
Orange
4 pole series 713 male connector
Protection IP67
Solenoid DIN 43650A - ISO4400
Protection IP65
Microsolenoid DIN 43650C - ISO4400
Protection IP65
Shielded cable 6x0.25 - 1m
Protection IP65
ELECTRICAL CONNECTION - connection diagram mV/V output
Code
V
Power supply
Power supply
Signal output
Signal output
Shunt Calibration
+
-
-
+
B
A
C
D
E - F
R-Cal n.c.
Code
P
Code
F
Code
E/M
1
2
4
3
5 - 6
White green
Black or
Yellow
Red
Blue /
Orange or
Violet
3
2
1
Non available
7
Cable shield connected to transducer body
Code
Z
1
2
4
3
Non available
ACCESSORIES ON REQUEST
Connectors
Connection E
3 pole connector + ground DIN43650A ISO4400
Prot. IP65
Connection M
3 pole connector + ground DIN43650C ISO4400
Prot. IP65
Connection Z
4 pole female cable connector M12x1
Prot. IP67
Connection Z
4 pole female cable connector, 90° M12x1
Prot. IP67
CON 006
CON 008
CON 293
CON 050
Connection P
7 pole female cable connector,
Prot. IP67
Connection P
7 pole female cable connector,
Prot. IP40
Connection P
7 pole female cable connector 90°,
Prot. IP40
Connection V
6 pole female cable connector,
Prot. IP66
EXTENSION CABLES
6 pole female connector (CON 300) + 2 m (6.5 ft) of cable (6x0.25)
6 pole female connector (CON 300) + 4 m (13 ft) of cable (6x0.25)
6 pole female connector (CON 300) + 6 m (20 ft) of cable (6x0.25)
6 pole female connector (CON 300) + 8 m (25 ft) of cable (6x0.25)
C02W
C04W
C06W
C08W
6 pole female connector (CON 300) + 10 m (33 ft) of cable (6x0.25) C10W
6 pole female connector (CON 300) + 15 m (50 ft) of cable (6x0.25) C15W
6 pole female connector (CON 300) + 20 m (66 ft) of cable (6x0.25) C20W
6 pole female connector (CON 300) + 25 m (82 ft) of cable (6x0.25) C25W
6 pole female connector (CON 300) + 30 m (100 ft) of cable (6x0.25) C30W
Other lengths on request
Pin
A
B
C
D
E
F
Cable color code
Wire
Red
Black
White
Green
Blue
Orange
CON 321
CON 320
CON 322
CON 300
ORDERING INFORMATION
Pressure Transducer
PROCESS CONNECTION
Standard
M18x1.5
1/2” G male
On request
3/4-16 UNF
G
M
L
TPF
ELECTRICAL CONNECTION
Standard
6 pole connector
7 pole connector
M12x1 connector (*)
6 pole shielded cable (**)
V
P
Z
F
4 pole solenoid connector (*) E
4 pole microsolenoid connector (*)
M
(*) Calibration signal not available
(**) 1mt cable included as standard. Custom lengths available, at extra cost.
Ex.: TPF - G - P - B01D - M - -
Flush fitting pressure transducer, M18x1.5 process connection, 7 pole electrical connector, 0...10 bar measurement range, ±0.5%FSO typical accuracy.
Mechanical and/or electrical characteristics differing from standard may be arranged on request.
H
M
ACCURACY
±0.2%FS typical
0...60 - 0...1000 bar (only)
±0.5%FS typical
0...10 - 0...50 bar ( only)
MEASUREMENT RANGE
B01D
B16U
B02D
B25U
B03D
B35U
Bar
0...10
0...16
0...20
0...25
0...30
0...35
B04D
B05D
0...40
0...50
B06D 0...60
B01C 0...100
B16D 0...160
B02C 0...200
B25D 0...250
B35D 0...350
B04C 0...400
B05C 0...500
B06C 0...600
B07C 0...700
B01M 0...1000
Psi
P15D 0...150
P25D 0...250
P03C 0...300
P05C 0...500
P75D 0...750
P01M 0...1000
P15C 0...1500
P02M 0...2000
P25C 0...2500
P03M 0...3000
P04M 0...4000
P05M 0...5000
P75C 0...7500
P10M 0...10000
P15M 0...15000
CALIBRATION STANDARDS
Instruments manufactured by Gefran are calibrated against precision pressure calibration equipment wich is traceable to
International Standards
GEFRAN spa reserves the right to make any kind of design or functional modification at any moment without prior notice
GEFRAN spa via Sebina, 74
25050 PROVAGLIO D’ISEO (BS) - ITALIA tel. 0309888.1 - fax. 0309839063
Internet: http://www.gefran.com
DTS_TPF_0108_ENG
