Dual Sided Frame One Utility Pole
Refer to page 4.
FrameOne
™
- Utility Pole
All electrical installations should be done by a qualified person in accordance with codes and regulations applicable at the installation site.
IMPORTANT: Read the entire assembly direction before starting installation.
HEX DRIVE
If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at
888.STEELCASE
(888.783.3522) for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico, and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
© 2010 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
Single Sided Frame One Utility Pole
Refer to page 2.
Page 1 of 11
939502067 Rev D
ATTACHMENT OF UTILITY POLE TO
SINGLE SIDED FRAME ONE BENCH
Refer to page 8 for information on removing ceiling tile.
1.
Install square aluminum block onto utility pole as shown .
2. a) Thread glide into pole base, then b) snap base into bottom of utility pole.
3.
Attach bracket to rail and secure with bolts provided.
3
BLOCK
BRACKET
1
Drive bolts through inside of power pole.
UTILITY
POLE
BASE
2a 2b
Page 2 of 11
939502067 Rev D
4.
Position pole assembly so that block extends into rail extrusion .
5.
Attach pole to bracket with (2) bolts provided.
6.
On the bottom of the pole / leg assembly a) Slide two halves of the support plate together, then b) secure them with (2) screws.
7.
Route power cords as needed, then refer to page 8 for information to install utility pole into a ceiling.
SUPPORT PLATE
6a
4
5
Drive bolts through inside of utility pole.
Drive screws through inside of utility pole.
6b
Bracket only shown for clarity.
Page 3 of 11
939502067 Rev D
ATTACHMENT OF UTILITY POLE TO
DUAL SIDED FRAME ONE BENCH
NOTE: Utility poles can not attach to continuous top benches.
1.
Install square aluminum block onto utility pole as shown .
2. a) Thread glide into pole base, then b) snap base into bottom of pole.
3.
Attach bracket to rail and secure with bolts provided.
3
BLOCK
BRACKET
1
Drive bolts through inside of power pole.
UTILITY
POLE
BASE
2a 2b
Page 4 of 11
939502067 Rev D
4.
Position pole assembly so that block extends into rail extrusion .
5.
Attach pole to bracket with (2) bolts provided.
4 5
Drive bolts through inside of utility pole.
Bracket only shown for clarity.
Page 5 of 11
939502067 Rev D
For Benches with Upper & Lower Trays:
(For benches with Simple Trays, skip to step 8)
6.
Install extension tray to utility pole with (4) screws provided.
7.
Install end cover by placing tabs in openings in channel, then swinging up and snapping cover in place.
END COVER
EXTENSION TRAY 7
Insert tabs in openings, then swing up.
SNAP!
6
Align (4) holes in tabs with holes in pole.
Page 6 of 11
939502067 Rev D
For Benches with Simple Trays:
8.
Install extension tray to utility pole with
(4) screws provided.
9.
Install end caps with screws provided.
Install (3) screws per end cap.
NOTE: End cap flanges fit inside the simple tray but outside the extension tray.
END CAPS
EXTENSION TRAY
8
Align (4) holes in tabs with holes in pole.
9
Page 7 of 11
939502067 Rev D
INSTALL UTILITY POLE INTO A CEILING
1.
Remove the ceiling tile where the pole will be placed and raise the utility “C” channel vertical.
2.
Cut ceiling tile hole.
3.
Assemble ceiling trim plate.
4.
Bend retainers up and insert ceiling trim plate into the ceiling tile cut-out.
3
4
1
2
3-1/4" x 6-1/4"
3-1/8"
1-5/8"
Page 8 of 11
939502067 Rev D
5.
Place ceiling tile with trim plate back in ceiling.
6.
Remove adjacent ceiling tile.
7.
Insert the vertical channel through the ceiling tile hole
NOTE: If the vertical channel extends above the ceiling tile more than 4 inches mark and cut excess material off before securing to the frame or junction bracket.
Deburr exposed edges.
8.
Route any power cords, harness and data cables as needed.
9.
Snap cover into place.
5
7
4" max
6
Page 9 of 11
939502067 Rev D
10.
Attach the ceiling bracket to the top of the vertical channel.
11.
Secure crossbar to the ceiling grid.
12.
Attach slotted adjustment bracket to the cross bar and fully tighten screw.
13.
Attach slotted adjustment bracket to the ceiling bracket. Be sure not to fully tighten the screws.
13
8-18 x 3/8"
8-18 x 1/4"
12
Gold #8-18 x .360"
11
5 of
9
8-18 x 1/4"
10
Page 10 of 11
939502067 Rev D
14.
Secure junction box to ceiling bracket and complete cabling.
MODULAR
8 - 18 x .375
Pan Head
HARDWIRE
15.
Snap the cover in place along the length of the vertical channel.
16.
Tighten screws connecting the slotted adjustment bracket to the ceiling bracket as shown on step 13.
TO BUILDING
TO BEAM
14
8-18 x 1/4" 15
Page 11 of 11
939502067 Rev D
