advertisement
TS9356 PKT 120/170
Surface Applied Closer
Pocket door track mount in 120°/170° pocket
(Closer on wall)
Installation instructions
08279971 – 08-2019
|
EN
|
dormakaba TS9356 PKT 120/170 (Closer on door)
Installation Instructions
Table of contents
Table of Contents
1 Technical specifications
1.1 Overview
1.2 Size selection chart
1.3 Tools recommended
1.4 Surface closer system
1.5 Handing the door
2 Installation instructions
2.1 Installing the back plate
2.2 Installing the surface closer
2.3 Installing track assembly
2.4 Installing main arm
2.5 Secure main arm
3 Adjustments 7
3.1 Adjust closing speeds: sweep, latch, backcheck, delayed action
3.2 Adjust spring force
7
8
4 Install covers 8
5
5
5
5
6
6
3
3
3
3
4
4
2 TS93 Surface Applied Closers 08279971 08-2019
dormakaba TS9356 PKT 120/170 (Closer on door)
Installation Instructions
1 Technical specifications
1.1 Overview
Caution: sex nuts are required for attachment of components to unreinforced doors and to wood or plastic faced composite type fire doors, unless an alternative method is identified in the individual door manufacturer’s listings.
Maximum degree of opening is 170°.
Minimum door width is 32”.
Adjust closer spring tension for proper closing and latching of door.
Adequate reinforcement by others required to install track in pocket.
Pocket depth is measured from the pull side face of the door at maximum opening.
Technical specifications
Requires DORMA EM504 electromagnetic door holder
Use closer body style “B” for this installation.
Arrows on closer mounting plate point upward.
Follow included template to properly prepare door and frame for all accessories of the closer installation.
Know the swing of the door which is being installed prior to installation.
Make sure door efficiently operates prior to installing closer.
Verify closer spring size prior to installation.
1.2 Size selection chart
Table 1
Closer
TS9356 PKT 120/170
Door width range Maximum weight
2’-8” to 4’” 150lbs
1.3 Tools recommended
Table 2
Drill bits:
Metal: No. 21 & 10-32 tap
Wood: 1/8”
#2 Phillips screwdriver
M2.5 hex key
M5 hex key
TS93 Surface Applied Closers 08279971 08-2019 3
dormakaba TS9356 PKT 120/170 (Closer on door)
Installation Instructions
1.4 Surface closer system
Fig.1
1 2
3
10 8 4 7 6 9
5
5
5
The surface closer is comprised of the following components.
1. Closer body
2. Main arm
3. Track assembly
4. Pinion
5. Cover and end caps
6. Closing/sweep speed adjustment
7. Latch speed adjustment
8. Backcheck adjustment
9. Delayed action adjustment
10. Backplate
Surface closer system
Handing the door
4
1.5 Handing the door
Fig.2
Left hand door (LH)
Hinge
Left hand reverse door (LHR)
TS93 Surface Applied Closers
Interior side of door
Right hand door (RH)
Hinge
Right hand reverse door (RHR)
Exterior side of door
08279971 08-2019
dormakaba TS9356 PKT 120/170 (Closer on door)
Installation Instructions
2 Installation instructions
2.1 Installing the back plate
Fig.3
Installing back plate
Installing surface closer
Installing track assembly
NOTE: Make sure arrows on plate point upward.
2.2 Installing the surface closer
Fig.4
Reference template 08279972
2.1.1 Attach the back plate to the installing surface using the four screws [10-32 machine screws or
#10 wood screws] provided with the surface closer.
3
2
1
Toward the hinge
NOTE: Orient pinion (1) closest to hinge.
2.3 Installing track assembly
Fig.5
A B
2
2.2.1 Secure the closer body (2) to the plate using the four M5x47mm flathead Phillips screws (3) provided with the plate itself.
1
C A
2.3.1 Position the components inside the track channel (1).
2.3.2 Attach the track channel to the wall through the end blocks with two flat head Phillips screws (2).
TS93 Surface Applied Closers 08279971
Right hand door
A. End block
B. Track channel
C. Slide shoe
08-2019 5
dormakaba TS9356 PKT 120/170 (Closer on door)
Installation Instructions
2.4 Installing main arm
Fig.6
Right hand door
Main arm
2
1
2.4.1 Align the arm (1) with the slide shoe of the track channel.
2.4.2 Secure with one M8x15mm shoulder bolt (2) using an M5 hex key.
2.5 Secure main arm
Fig.7
2 1
Right hand door
2.5.1 With the door closed and using an adjustable wrench (looking up at the bottom of the closer):
• Left hand door - turn the bottom pinion clockwise approximately 5°.
• Right hand door - turn the bottom pinion counter-clockwise approximately 5°.
2.5.2 Attach the main arm (1) to the top pinion with an M6x20 socket head cap screw (2) using an M5 hex key.
Be sure that the door is fully closed during
application.
6 TS93 Surface Applied Closers 08279971 08-2019
dormakaba TS9356 PKT 120/170 (Closer on door)
Installation Instructions
3 Adjustments
Set closer spring size prior to making any closing speed adjustments.
Do not back valves out beyond closer casting.
Adjust closing speeds
Maximum opening angle is 170º.
Door should close in 3 to 6 seconds from 90º.
Do not close valves completely.
3.1 Adjust closing speeds: sweep, latch, backcheck, delayed action
Fig.8
1 [Sweep] 2 [Latch]
3 [Backcheck]
170°
Sweep
Latch
7° 4 [Delayed action]
Backcheck
Delayed action
70°
65°
3.1.1 Adjust the closing sweep speed (1) for the area from 70° - 0°
• Increase sweep speed: Turn valve counterclockwise
• Decrease sweep speed: Turn valve clockwise.
3.1.2 Adjust the closing latch speed (2) for the area
• from 7° - 0°.
Increase latch speed: Turn valve counter-
• clockwise
Decrease latch speed: Turn valve clockwise.
Decrease
Increase
Sweep &
Latch
Increase Backcheck &
Decrease
Delayed actions
3.1.3 Adjust the opening backcheck (3).
• Increase resistance: Turn valve clockwise
• Decrease resistance: Turn valve counterclockwise.
•
•
3.1.4 Adjust the closing delayed action (4) for the area from 170° - 70°.
Increase delayed action: Turn valve clockwise
Decrease delayed action: Turn valve counterclockwise
TS93 Surface Applied Closers 08279971 08-2019 7
dormakaba TS9356 PKT 120/170 (Closer on door)
Installation Instructions
3.2 Adjust spring force
Fig.9
Increase
Decrease
Adjust spring force
Secure covers
TS9356
Door width
4’
4’-6”
Full turns of spring adjust
0
+5
Closer size
5
6
TS9356
NOTE: Supplied with a size 6 spring setting.
Increase force: turn clockwise 6 times (max)
4 Install covers
Fig.10
2
4
3
3
1
1
4.1.1 Snap both end covers (1) into place.
4.1.2 Remove the un-needed tab (2), and snap the closer body cover (3) into place.
4.1.3 Secure with a 4-40 Phillips pan head screw (4) .
8 TS93 Surface Applied Closers 08279971 08-2019
www.dormakaba.com
dormakaba
DORMA USA, Inc.
1 Dorma Drive, Drawer AC
Reamstown, PA 17567
USA
T: 717-336-3881
F: 717-336-2106
advertisement
Related manuals
advertisement