advertisement
MODEL 3334 POWER MEAT CUTTER
OPERATING AND SERVICE MANUAL
REVISED – SERIAL No. 1,000 ON
SQ. BASE #35323 ON
FLAT TOP #35323 ON
+
IMPORTANT NOTICE
+
This Manual contains important safety instructions which must be strictly followed when using this equipment.
PTCT 3334
100-11-04-28
TABLE OF CONTENTS
Page
NOTICE TO OWNERS AND OPERATORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SAFETY TIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
WARNING LABELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
TO PROCESS PRODUCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 & 7
CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
LUBRICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
WALL CHART (PART No. 671) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
MOTOR ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
SAW GUIDE BAR AND SAW GUARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 & 13
PARTS DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
PARTS DIAGRAMS, SERIES 4003 CARRIAGE & CHANNEL . . . . . . . . . . . . . . . . . . . . . . 21, 22, 23
NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
MOTOR COVER APPLICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
PARTS DIAGRAMS, LOWER REMOVABLE WHEEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
SWITCH ASSEMBLIES AND SERVICE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 & 27
WIRING DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28, 29, 30
PARTS LIST/ORDERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 & 31
PARTS ASSEMBLIES LIST/ORDERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
STAINLESS STEEL HEAD STRUCTURE HISTORY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
WEARABLE SAW PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
WARNING LABEL LOCATIONS ON MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 & 35
NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
OPERATOR’S SIGNATURE PAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
NOTICE TO OWNERS AND OPERATORS
BIRO’s products are designed to process food products safely and efficiently. Unless the operator is properly trained and supervised, however, there is the possibility of a serious injury. It is the responsibility of the owner to assure that this machine is used properly and safely, strictly following the instructions contained in this Manual and any requirements of local law.
No one should use or service this machine without proper training and supervision. All operators should be thoroughly familiar with the procedures contained in this Manual. Even so BIRO cannot anticipate every circumstance or environment in which its products will be used. You, the owner and operator, must remain alert to the hazards posed by the function of this equipment – particularly the SHARP MOVING BAND TYPE SAW BLADE. No one under eighteen (18) years of age should operate this equipment. If you are uncertain about a particular task, ask your supervisor.
This Manual contains a number of safe practices in the SAFETY TIP section. Additional warnings are placed throughout the Manual. Warnings related to your personal safety are indicated by:
OR
Warnings related to possible damage are indicated by:
BIRO also has provided a wall chart to be posted near the equipment. If any warning label, wall chart, or Manual becomes misplaced, damaged, or illegible, please contact your nearest Distributor or BIRO directly for a replacement.
Remember, however, this Manual or the warning labels do not replace the need to be alert and to use your common sense when using this equipment.
This Manual applies to machines with serial number 1,000 and higher.
1
SAFETY TIPS
SHARP MOVING BAND TYPE SAW BLADE
TO AVOID SERIOUS PERSONAL INJURY
NEVER Touch This Machine Without Training and Authorization By Your Supervisor.
ALWAYS Read Operation and Parts Manual BEFORE Operating, Cleaning or Servicing.
ALWAYS Keep Hands Clear of Sharp Band Type Saw Blade and Other Moving Parts.
ONLY Use a Qualified Electrician to Install According to Local Building Codes: Machines MUST
Be Properly Grounded.
ONLY Install on Level, Non-Skid Surface in a Clean, Well-Lighted Area Away From Children and
Visitors.
DO NOT Attempt to Operate This Machine Until it has Been Inspected and Demonstrated by the
Seller – Recognized BIRO Representative.
DO NOT Alter or Modify This Machine in any Way From its Original Form. This Machine in its
Original Form Meets the Intent of O.S.H.A. Applicable Standards.
NEVER Operate with Saw Guard on Saw Guide Bar in the Raised Position or the Saw Guard
Removed from the Saw Guide Bar.
ALWAYS Adjust the Saw Guide Bar with Saw Guard to Within
1
2
" of Product to be Cut.
ALWAYS Use Supplied Safety End Cut Pusher Plate for Smaller Products or The Last Cuts of
Product.
DO NOT Use This Machine for Non-Food Products.
DO NOT Use This Machine to Cut Pigs Feet.
DO NOT Wear Gloves While Operating.
ALWAYS Turn Off, Unplug From Power Source and Perform Lockout/Tagout Procedure to This
Machine BEFORE Removing Shrouds, Removable Guards, Covers, Doors, Fences or Panels for Cleaning, Servicing or Any Other Reason.
NEVER Leave Machine Unattended While Operating.
PROMPTLY REPLACE Any Worn or Illegible Warning Labels.
USE ONLY BIRO Parts and Accessories Properly Installed.
2
INSTALLATION
TO AVOID SERIOUS PERSONAL INJURY
PROPERLY INSTALL EQUIPMENT IN ADEQUATE WORK AREA
ALWAYS Use Qualified Technician and Electrician for Installation.
ALWAYS Install Equipment in Work area with Adequate Light and Space.
ONLY Operate on a Solid, Level, Non-Skid Surface.
NEVER Operate with Saw Guard on Saw Guide Bar in the Raised Position or the Saw Guard
Removed from the Saw Guide Bar.
ALWAYS Adjust Saw Guide Bar with Saw Guard to Within
1
2
" of Product to be Cut.
NEVER Operate Without all Warning Labels Attached and Wall Chart Posted.
1. Read this Manual thoroughly before installation and operation. Do not proceed with installation and operation if you have any questions or do not understand anything in this Manual. Contact your local Distributor, or BIRO first.
2. Install machine on a level, solid, non-skid surface in a well-lighted work area away from children and visitors.
ALWAYS LEVEL MACHINE BEFORE USING
3. After installing machine in operational area, it is imperative that the four adjusting legs be adjusted to level the machine.
4. To assemble meat gauge plate (Part No. AS16275) to the machine; Loosen the lock knob (Part No. 272-7-1) on the right side of meat gauge bracket. Raise the meat gauge gear rack (Part No. S16272) and slip the meat gauge plate over the gear rack. Lower the gear rack back to its original position, tighten lock knob. Keep gear rack well oiled with food grade oil to ensure free movement.
5. The head structure (Part No. 16005) comes detached from the base. Slip the head into the slide gibs (Part No.
260) located on the back of the base structure. Make sure the slide gibs are oiled or greased to ensure free vertical movement of the head structure.
3
6. Place removable finger lift with saw guard assembly (Part No. A211) on the saw guide bar (Part No. 116-22) and fasten in place with finger lift fastener knob (Part No. 211A-291Q).
SHARP SAW BLADE. HANDLE WITH EXTREME CAUTION
7. Placing blade on cutter: Hang upper wheel assembly (Part No. A16003U335-6) on the hinge bracket (Part No.
71-1). lift the nylon filler (Part No. 177). Hang blade on the upper wheel and hold with right hand. With left hand force the back of the blade between the front blade cleaners (Part No. 131), located below the nylon filler. Lower the nylon filler and insert the back of the blade in the upper saw guide (Part No. 602B). The blade has already dropped over the lower wheel. With right hand force the back of the blade between the rear blade cleaners (Part
No. 131). The blade is now ready to be tightened. Press down on the ratchet arm (Part No. 10-1) located at the rear of the base structure. Turn the upper wheel slowly by hand to ensure proper tracking of the saw blade on the wheels. Tighten to proper tension. When the tension gauge (Part No. 16197), located at the bottom rear of the head becomes tight laterally the blade is at proper tension.
8. The side platter bracket (Part No. S12214B) is packed loose in the machine and must be installed on the left side of the base structure with the supplied hardware and checked for proper adjustment. Stationary platter must be flat.
9. The stationary platter (Part No. A16163-1) is placed on top of the base structure and held in place by two push-pull hold down catches (Part No. 16212), located on the base structure.
10. The sliding meat carriage assembly (Part No. A16155) is installed by turning the movable stop assembly (Part No.
A16200) clockwise.
After the carriage assembly is in the channel for operation, turn the movable stop counterclockwise to lock.
11. Post SAFETY TIPS wall chart within easy view of operator. Keep Manual available to operator.
12. Machine MUST be properly grounded. Use qualified electrician to install according to building codes.
WIRING MOTOR
(1) Interchange of current is made in motor outlet box. Leads are properly marked. Changing instructions are on motor plate or motor outlet box.
(2) All cutters are wired 220 volts unless otherwise specified. Be sure motor specifications (voltage, cycle, phase) match power supply line. Be sure line voltage is up to specification.
(3) Connect leads to machine in a manner that will be approved by local electrical inspectors.
(4) We recommend no less than No. 12 wire. If the leads are too light, machine may not have sufficient cutting power and/or speed.
(5) The drive belt is packed loose in machine to prevent deformation, and must be installed on pulleys at time of wiring motor.
(6) The BIRO Manufacturing Company is not responsible for permanent wiring, connection or installation.
NOTE TO OWNER AND ELECTRICIAN: IF THIS MACHINE IS NOT CORD
AND PLUG CONNECTED TO THE ELECTRICAL SUPPLY SOURCE, THEN IT
SHOULD BE EQUIPPED WITH, OR CONNECTED TO, A LOCKABLE,
MANUALLY OPERATED DISCONNECT SWITCH (OSHA 1010.147).
KEEP HANDS CLEAR OF SHARP MOVING BAND TYPE SAW BLADE
4
13. Make sure saw guide bar with saw guard is in its lowest position. Close head and base doors.
14. Push start button and check for proper phasing of motor. Blade should be traveling down through saw guide.
15. Watch for proper tracking of blade. Back of blade should be centered in hole in saw guide in stationary bar (Part
No. 119A). Push stop button to stop machine.
16. Check placement of all warning labels, wall chart and Manual. Machine is ready for trained operators to process product.
17. Contact your local Distributor or BIRO directly if you have any questions or problems with the installation or operation of this machine.
WARNING LABELS
FOR BIRO POWER MEAT CUTTERS
SEE PAGE 32 AND 33 FOR LOCATIONS ON MACHINE
5
OPERATION
SHARP MOVING BAND TYPE SAW BLADE
TO AVOID SERIOUS PERSONAL INJURY
ONLY Properly Trained Personnel Should Use This Equipment.
ALWAYS Keep Hands Clear of Band Type Saw Blade and Other Moving Parts.
NEVER Operate with Saw Guard on Saw Guide Bar in the Raised Position or the Saw Guard
Removed from the Saw Guide Bar.
ALWAYS Adjust the Saw Guide Bar with Saw Guard to Within 1
2
" of Product to be Cut.
ALWAYS Use Safety End Cut Pusher Plate for Smaller Products or The Last Cuts of Product.
DO NOT Wear Gloves While Operating.
DO NOT Tamper With, Bypass, Alter, or Modify this Equipment in Any Way From Its Original
Condition.
ALWAYS Turn Off, Unplug from Power Source and Perform Lockout/Tag Out Procedures Before
Cleaning, Servicing or When Not in Use.
NEVER Leave Unattended While Operating.
NEVER Operate Without All Warnings Attached and Wall Chart Posted.
A. TO PROCESS PRODUCT
1. Before starting power cutter, adjust saw guide bar with saw guard down to within ½
² (13 mm) of product to be cut.
6
DO NOT WEAR GLOVES WHILE OPERATING
2. Make sure all doors are closed and locked.
3. Adjust meat gauge plate forward to desired thickness of cut.
4. Push start button and watch blade for proper tracking.
5. Standing in front of the power cutter, place product on the meat carriage. Pay attention to position of your hands. Keep hands clear of moving band type saw blade. Leaning lightly against the scalloped front edge of meat carriage, hold the product firmly in right hand with product face flush against meat gauge plate. Move the meat carriage from right to left at a steady rate until fully past the saw blade. Use left hand to remove and stack cut product, NEVER REACH IN FRONT OF BAND TYPE SAW BLADE. On the return stroke, pull the product toward you, away from saw blade.
NEVER REACH OR GRAB FOR PRODUCT IN FRONT OF
MOVING BAND TYPE SAW BLADE
6. ALWAYS use the Safety End Cut Pusher Plate (Part No. 256P) for smaller products or the last cuts of product.
The pusher plate is supplied as standard on all BIRO power cutters.
7. When finished cutting, push stop button. Perform lockout/tag out procedure.
7
CLEANING
SHARP MOVING BAND TYPE SAW BLADE
TO AVOID SERIOUS PERSONAL INJURY
ALWAYS Turn Off, Unplug From Power Source and Perform Lockout/Tagout Procedure to This
Machine BEFORE Cleaning or Servicing.
ONLY Use Recommended Cleaning Equipment, Materials and Procedures.
NEVER Spray Water or Other Liquid Substances Directly at Motor, Power Switch or any Other
Electrical Components.
ALWAYS Thoroughly Clean Equipment at Least Daily.
CLEANING THE BIRO POWER CUTTER:
Disconnect electrical power to the machine before cleaning. Parts to be removed have been made accessible and can be removed without tools. Notice in the drawing below that all parts are numbered. Each part should be removed for cleaning in the numbered sequence shown. To ensure cleaner cuts, keep the cleaning system in good condition.
Parts on the cleaning system which should be checked weekly, and changed as required are as follows: Wheel
Cleaners (Part No. 179), Saw Cleaners (Part No. 131), Saw Guide in Stationary Bar (Part No. 119A), Upper Saw Guide
(Part No. 602B), Lower Blade Back-Up Guide (Part No. 605) and Nylon Filler (Part No. 177).
8
MAINTENANCE
SHARP MOVING BAND TYPE SAW BLADE
TO AVOID SERIOUS PERSONAL INJURY
ALWAYS Turn Off, Unplug From Power Source and Perform Lockout/Tag Out Procedure to This
Machine BEFORE Cleaning or Servicing.
NEVER Touch This Machine Without Training and Authorization By Your Supervisor.
ALWAYS Keep Hands Clear of Band Type Saw Blade and Other Moving Parts.
NEVER Bypass, Alter, or Modify This Equipment in Any Way From Its Original Condition.
PROMPTLY REPLACE Any Worn or Illegible Warning Labels.
USE ONLY GENUINE BIRO Parts and Accessories Properly Installed.
A. GENERAL
1. Machine should be generally inspected every time it is cleaned (at least daily) to ensure that it is in good condition and has not been damaged or tampered with.
a. SAW WHEELS: Clean outer diameter grooves daily. Check for cracks, gouges or wear on the flange and grooves.
DO NOT IMMERSE UPPER WHEEL
ASSEMBLY IN WATER b. WHEEL CLEANER ASSEMBLIES: Check condition of fiber cleaner, change every four (4) weeks.
c. REMOVABLE FINGER LIFT ASSEMBLY: Check condition of saw guard, make sure mounting bolts are tight and DANGER EXPOSED BLADE decal is attached and legible. Check condition of upper saw guide
(Part No. 602B), replace every six (6) months. Check adjustment of upper saw guide. Should be ” between back of blade and saw guide carbide.
NEVER USE THIS MACHINE WITHOUT PROPERLY INSTALLED
AND FUNCTIONING SAW GUIDE BAR AND SAW GUARD d. SAW GUIDE BAR: Check condition of bar for coating peeling and wear, replace as necessary. Check saw guide bar spring for proper tension. The spring should hold the bar in any desired position in its travel.
Replace saw guide bar spring (Part No. 193) as necessary using instructions on following page.
9
1. Remove the finger lift fastener knob and the fingerlift assembly.
2. Remove the finger lift fastener stud.
3. Push the saw guide bar up and out of the top of the head structure.
4. Remove the saw guide bar spring.
5. Clean and lubricate the babbitt pocket area (the square indented area that seats the saw guide bar spring).
6. Lower the new saw guide bar spring through the top of the babbitt pocket area and guide the spring into position with a standard screwdriver. (NOTE: Drawing)
7. While holding the saw guide bar spring in position, re-enter the saw guide bar from the top compressing the saw guide bar spring slightly until the saw guide bar slides past the spring.
8. Replace the finger lift fastener stud, the fingerlift assembly and the finger lift fastener knob.
9. Test by making several adjustments.
e. STATIONARY BAR ASSEMBLY: Check condition of nylon filler (Part No. 177), change every four (4) weeks.
Check condition of saw guide (Part No. 119A), check tracking of blade through guide, back of blade should be centered in hole, replace every six (6) months. Check condition of lower blade back-up guide (Part No.
605). Check adjustment of back-up guide, should have
1
32
² gap between back of blade and saw guide carbide. Replace every six (6) months.
f. SAW CLEANERS: Check condition of blade cleaners, replace every four (4) weeks.
g. RATCHET ASSEMBLY: Check for smooth operation through full range of travel. Check condition of trigger spring, replace as necessary.
h. SLIDE GIBS: Check that head structure moves freely up and down. Check for side to side and front to rear tolerance, adjust as required. Grease every four (4) weeks.
i. MEAT GAUGE ASSEMBLY: Check free movement of meat gauge plate on gear rack. Gear rack to be kept lubricated at all times with light food grade oil. Check operation of release handle. Check that worm gear engages properly with gear rack. Check tension of release handle spring, replace as necessary.
j. MEAT CARRIAGE ASSEMBLY: Check for free movement through full range of travel. Check for side to side tolerance, adjust as necessary. Check condition and grease bearings, replace as necessary. Check condition of thumb guard, replace as necessary.
k. SAFETY ITEMS: Safety end cut pusher plate is with machine and accessible. All warning labels are present, properly affixed and legible. Model and Serial Number plate properly affixed and legible. Wall poster within operators view from machine. Manual accessible to operator.
B. LUBRICATION
1. UPPER WHEEL BEARINGS: Grease every four (4) months.
Change grease every twelve (12) months.
2. LOWER
BEARING HOUSING:
Grease every four (4) months.
Change grease every twelve (12) months.
3. SLIDE GIBS: Grease every four (4) weeks.
4. MEAT CARRIAGE BEARINGS: Grease every four (4) weeks.
5. SAW GUIDE BAR: Oil daily with food machine oil.
6. MEAT GAUGE GEAR RACK: Oil daily with food machine oil.
When lubricating the upper wheel bearing it is important that the three hex head screws securing the upper wheel hub cap be loosened slightly before attempting to pump grease into the grease fitting. Loosening the screws allows for an escape of old broken down grease and air from the bearing cavity. Failure to loosen the screws before greasing the upper bearings can cause the upper shaft seal to be dislodged from the upper wheel allowing grease to escape and moisture to get into the cavity.
When finished greasing the bearings, retighten the three screws. Take care to also clean off any grease that was forced out of the cavity during greasing.
10
ITEM NUMBER 671
WALL CHART “BAND SAW SAFETY GUIDELINES”
ATTACH TO WALL IN VICINITY OF MACHINE IN EASY VIEW OF OPERATOR
WARNING
ONLY PROPERLY TRAINED PERSONNEL
SHOULD USE THIS EQUIPMENT
This Saw Contains A Sharp Blade.
To Reduce Risk of Injury:
1. Before Using, Make Sure:
. Gauge Plate
Are Secure.
!
And Other Components
. All Warning Labels And Guards Are In Place.
. The Guide Bar
"
Is Adjusted To ½ Inch
Above The Product To Be Cut
2. While Cutting:
. Keep Hands and Fingers Away From Blade.
. Keep Product Securely Against Gauge Plate.
. Use End Cut Pusher
#
When Making
Final Cuts. Item No. 256P.
3. Before Cleaning:
. Turn Off Power and Unplug.
. Remove Saw Blade.
. Use Extra Care When Handling The Saw Blade.
USE YOUR
MEAT SAW SAFELY!
SEE PARTS AND SERVICE MANUAL SUPPLIED WITH MACHINE FOR ADDITIONAL SAFETY INFORMATION.
11
C. MOTOR ADJUSTMENT
Starting with Serial Number 27958 three (3) phase Model 3334’s will no longer be equipped with an adjustable motor base plate, Part No. 16015-10 and 16015-11. The motor will be bolted to the bottom of the base structure and
V-belt tension adjusted utilizing shims.
This change has evolved as a result of the market demand for higher blade speeds. The revised mounting procedure will insure a more rigid motor installation creating positive belt alignment and minimizing machine vibration.
The base bottom has been redesigned to accept the frame sizes of the current 3 phase motors. Units prior to Serial Number 27958 can be retrofitted by ordering Part No. 16015-12 motor base plate and template (flat), and 36 pieces Part No. 324A motor shims.
ADJUSTMENTS
1. For tightening motor V-belt on rigid base plate, remove appropriate quantity of shims (Part No. 324A) under the motor until the desired total flex of the V-belt is approximately ½”.
1. For tightening motor V-belt on old style floating adjustable motor mounting plates (Part No. 16015-10 and 16015-11), loosen the upper wing nuts (Part No. 16015-3).
Then loosen the bottom wing nuts (Part No. 16015-3) which are located under the mounting plate. This enables the motor mounting plate to drop to the desired belt tension.
Re-tighten the upper wing nuts evenly so that the motor stays horizontal. Do not tighten belt to extremes. This will cause undue pressure on and premature failure of the motor bearings.
D. SAW GUIDE BAR AND SAW GUARD
The factory recommends that when service is performed on any BIRO SAW the servicing agency be sure that the
BIRO SAW is equipped with the most current safety features available.
In September 1969 production of the Model 3334 began and is current. The Model 3334 was first equipped with
19” saw guide bar until March 1973 when the length was extended to 23”. In June 1977, the bar was shortened to
22” and is used in current production.
The same saw guard (Part No. 255) on saw guide bar used on the Models 33 and 34 was carried over to the Model
3334 and used in production until June 1975.
Part No. 663 Saw Guard on saw guide bar replaced Part No. 255 in June 1976 starting with Serial No. 12242. At the same time, the Part No. 661 Guard on head Door introduced in 1974 was replaced by Part No. 661-1 Guard on
Head Door. Both Part No. 663 and 661-1 are current production today.
The factory recommends that all Model 3334’s prior to Serial No. 12242 be updated by installing the current SAW
GUIDE BAR ASSEMBLY (Part No. A116-22) and SAW GUARD ON HEAD DOOR (Part No. 661-1).
12
13
14
15
Item No.
A16005
A16006
A16014L
16014L-1
A16014U
A16112
A661-1
A71-1
HHS025S
HHS035S
HHS050S
HHS060S
HN15S
LW10S
LW15S
Description
Head & door assembly
Head door assembly
Head door hinge assembly, lower
Head door hinge – short pin
Head door hinge assembly, upper
Head door latch assembly
Saw guard on head door assembly
Upper wheel hinge bracket assembly
Hex head screw,
1
4
-20
´
1
2
SS
Hex head screw,
Hex head screw,
Hex head screw,
1
5
5
4
-20
´
5
16
16
-18
´
5
8
8
SS
SS
-18
´ 1 SS
Hex nut, 1
4
-20 SS
Lock washer,
Lock washer,
1
4
5
16
SS
SS
Item No.
SSS15
112-212
116KS
14GP
14GP-1
16005
16006
16014L
16014U
16112
193
194
661-1
71-1
Description
Set screw 5
16
-18
´
5
Waved washer
16 cup point
Saw guide bar lock knob – aluminum head
Head door hinge pin, 1 1
2
"
Head door hinge pin, 1
Head, aluminum
Head door, aluminum
1
4
"
Head door hinge, lower half *NSS
Head door hinge, upper half *NSS
Head door latch
Guide bar spring
Locking knob pad
Saw guard to head door
Upper wheel hinge bracket
Item No.
A16112
AS16005
AS16006
A71-1
HHS050S
HHS060S
LW15S
SSS15
S16005C
S16006
14R
14TP
14TP-1
112-212
16112
193
194
194KS-1
71-1
Description
Head door latch assembly
Head & door assembly SS
Head door assembly SS
Upper wheel hinge bracket assembly
Hex head screw,
5
16
-18
´
5
8
SS
Hex head screw,
5
16
-18
´ 1 SS
Lock washer,
Set screw cup point
5
16
5
16
SS
-18
´
5
16
Head SS
Head door SS
Head door hinge, welded
Head door hinge pin, 1
1
Head door hinge pin, 1
Waved washer
1
2
"
4
"
Head door latch
Guide bar spring
Locking knob pad
Saw guide bar lock knob – stainless head
Upper wheel hinge bracket
16
Item No.
Description
A16003U-6
Upper wheel assembly without hinge plate
A16003U335-6
Upper wheel assembly with hinge plate
A16003UDF-6
Upper double flange wheel assembly without hinge plate
A16003UDF335-6 Upper double flange wheel assembly with hinge plate
A247-1
AS16335X
A227
A295
Upper shaft bearing assembly
Upper wheel hinge plate assembly
Bearing cup/cone assembly
Wheel cleaner assembly
Item No.
HHS005S
HHS010S
HN05S
HN35S
S16335X
S229
S244
S253
S295
S325
16003U-6
179
230DL
234
237
238
247
248
252X
513
530
Description
Hex head screw, 8-32
´
1
2
Hex head screw, 10-32
´
3
Hex nut 8-32 SS
SS
8
SS
Hex nut 3
8
-16 SS
Upper wheel hinge plate, SS
Wheel cleaner arm torsion spring, SS
Wheel cleaner arm stud, SS
Upper wheel aligning screw, SS
Wheel cleaner arm, SS
Wheel cleaner washer, SS
Upper wheel, 16", 6 spoke
Wheel cleaner
Upper shaft seal, double lip
Grease fitting, upper wheel
Upper shaft castellated lock nut
Upper shaft castellated lock nut washer
Upper shaft
Upper wheel hub cap
Shaft lock nut
Upper wheel hub gasket
Retaining ring (2 req.)
Item No.
A16360
A16361
A363
HN25S
LW25S
SSS20
S360CB-1
12251AL
16003-6
16003DF-6
Description
Lower bearing housing assembly without wheel
Lower shaft bearing assembly
Bearing cup/cone assembly
Hex nut, 3
8
-16 SS
Lock washer,
Set screw, 3
8
3
8
SS
-16
´
3
8 cup point
Carriage bolt, 3
8
-16 1 1
4
SS
Upper V-belt pulley 9
´ 1 AL
Lower wheel 16", 6 spoke
Lower double flange wheel 16
², 6-spoke
17
16251AL
16303
16360
16361
231DL
277
300
360A1
360B-1
362
Upper v-belt pulley, 11.4
´ 1 AL
Lower shaft nut
Lower bearing housing
Lower shaft
Lower shaft seal, double lip
Lower shaft key
Lower shaft Woodruff key
Grease fitting
Set screw,
1
2
-13
´
1
2 flat point
Lower bearing housing adj. cap
Item No.
A19-1
FW07S
HHS040S
HN15S
HN35S
LW10S
S11
S189
S19
10-1
19CB
S240
Description
Ratchet assembly
Flat washer, 3
8
SS
1
Hex head screw,
4
-20
´ ¾ SS
Hex nut, 1
4
-20 SS
Hex nut, 3
8
-16 SS
Lock washer, SS
Ratchet trigger SS
Ratchet arm stud SS
Ratchet base SS
Ratchet arm
Carriage bolt 1
4
-20
´
3
Ratchet trigger spring
4
SS
Item No.
Description
A16278
Meat gauge plate assembly less release
A262
assembly
Meat gauge release assembly
AS16273-S275
Meat gauge assembly
AS16275
FW10S
HHS035S
HHS049NL
HHS060S
HN20S
LW10S
LW15S
S16272
S16273
Meat gauge plate assembly with release assembly
Flat washer,
5
16
, SS
Hex head screw ¼-20
Hex head screw, 5
´
5
16
-18
´
1
8
2
, nylon
Hex head screw,
Hex nut,
5
16
-18
´ 1, SS
5
16
-18, SS
Lock washer,
1
4
, SS
Lock washer, 5
16
, SS
Meat gauge gear rack, stainless
Meat gauge bracket, SS
S16275
Meat gauge plate, SS
Item No.
S235
S262
16278
264G
264-1
264-1S
S265
267
270
271AL
272-7-1
272-8
272-9
272-12
272-13
272-14
18
Description
Taper pin, 4
´
3
4
, SS
Meat gauge release handle, SS
Meat gauge arm
Meat gauge hand wheel groove pin
Meat gauge hand wheel
Hand wheel shim
Meat gauge release spring
Meat gauge release cotter key
Meat gauge release pin
Meat gauge worm gear, aluminum
Lock knob, 5
16
-18, 3 point
Cap nut,
5
16
Hex bolt, 5
16
-18 SS
-18
´ 2 SS
Brass ball
Hex head screw,
Castellated nut, 5
5
16
16
-18
´ 1
1
-18, SS
4
, SS
Item No.
A116-22AL
A116-22SS
A116-22-COS
A211-AL
A211-SS
A211-COS
A602
FW05S
HHS015S
HHS020S
HHS083S
HN10S
LH663
LW05S
LW10S
RHS10S
RHS30S
S200B1
116KS
116-22
116-22-COS
16662
17211-22
17211-35
193
194
194KS-1
211
211A-291Q
601
602B
602AFSC
663
708
Description
Saw guide bar assembly 22" – aluminum
Saw guide bar assembly 22" – stainless
Saw guide bar assembly – 22" SS special
Finger lift assembly, removable – aluminum
Finger lift assembly, removable – stainless
Finger lift assembly – removable SS special
Saw guide assembly, upper
Flat washer, 1
4
SS
Hex head screw, 10-32
´
7
Hex head screw, 1
8
SS
Hex head screw
3
8
Hex nut, 10-32 SS
4
-20
´
3
8
SS
-16
´ 1¾ SS
Saw guard for true left head
Lock washer, #10 SS
Lock washer, 1
4
SS
Round head screw, 10-32
´
3
Round head screw, 1
4
-20
´
7
Stop stud on guide bar
8
4
SS
SS
Saw guide bar lock knob – aluminum head
Saw guide bar, 22"
Saw guide bar – 22" special
Saw guard for SS head
Finger lift, shim, .022
Finger lift, shim .035
Saw guide bar spring
Locking Knob pad
Saw guide bar lock knob – stainless head
Finger lift bracket
Fastener knob, 4 point
Upper saw guide bracket
Upper saw guide with carbide
Upper saw guide, narrow, fish
Saw guard for aluminum head
Decal “DANGER EXPOSED BLADE”
19
Item No.
A16Z
A295
AS16290
FW05S
HHS003S
HHS005S
HHS035S
HHS040S
HHS070S
HN05S
HN10S
LW10S
LW25S
RHS20S
S16290
S229
S235
S244
S295
S325
131
16Z
179
211A-291Q
228-2
605
Description
Guide bracket saw cleaner assembly
Wheel cleaner assembly
Cleaning unit total assembly
Flat washer, 1
4
SS
Trimmed hex head screw 8-32
´
1
Hex head screw, 8-32
´
1
Hex head screw,
Hex head screw,
Hex head screw,
1
1
3
4
-20
´
5
4
-20
´
3
2
8
SS
8
4
SS
-16
´ 1 SS
Hex nut, 8-32 SS
SS
4
, SS
Hex nut, 10-32 SS
Lock washer, 1
4
SS
Lock washer,
3
8
SS
Round head screw, 10-32
´ 1
1
Cleaning unit stamping, SS
8
SS
Wheel cleaner arm torsion spring SS
Taper pin 4
´
3
4
, SS
Wheel cleaner arm stud SS
Wheel cleaner arm SS
Wheel cleaner washer SS
Saw cleaner SS
Lower guide bracket saw cleaner holder
Wheel cleaner
Fastener knob, 4 point
Lower guide washer
Saw guide lower blade back-up
Item No.
A415D
HN15S
LW10S
S268
119A
177
415D
Description
Stationary bar assembly
Hex nut 1
4
-20 SS
Lock washer,
1
4
SS
Stationary bar headless screw
Saw guide in stationary bar
Nylon filler
Stationary bar
Item No.
A130
A16132
HHS003S
HHS025S
LW10S
130
131
16132
175-2-S
16133
Description
Saw cleaner assembly
Steel cleaner assembly, rear
Trimmed hex head screw 8-32
´
1
Hex head screw,
Lock washer, 1
4
1
4
SS
-20
´
1
2
SS
Saw cleaner bracket rear
Saw cleaner SS
Saw cleaner bracket holder, rear
Thumb screw, 1
4
-20
´
1
2
Fastener knob – 4 point
4
, SS
Item No.
AS415D
HHS025S
LW10S
S268
S415D
119A
177
Description
Stationary bar assembly SS
Hex head screw 1
4
-20
´ ½ SS
Lock washer,
1
4
SS
Stationary bar headless screw
Stationary bar SS
Saw guide in stationary bar
Nylon filler
20
Item No.
A16196
HHS040S
LW10S
111AL
118
16197
196
198
Description
Tension spring assembly
Hex head screw, 1
4
-20
´
3
Lock washer, 1
4
SS
4
Tension spring pin, ALI
Tension spring plate
Tension spring gauge
Saw tension spring
Cap, for tension pin
SS
Item No.
A16155
A175S
FW05S
AN15S
AN20S
HN30S
LW20S
S155
S155-R
S155-11
Description
Meat carriage assembly complete
Thumb guard assembly
Flat washer,
Acorn nut,
Acorn nut,
1
3
1
4
-20 SS
8
4
SS
-16 SS
Hex nut, 3
8
-16 light jam SS
Lock washer 3
8 regular SS
Meat carriage top only (NSS)
Raw meat carriage top only (DNS)
Meat carriage stop thumb screw
Item No.
16155
16155-2A
16155-2B
16155-2C
16155-13
16155AEZ-1
16159
175S
175-1-S
175-2-S
Description
Meat carriage top & angle only
Meat carriage guide
Meat carriage guide spacer,
1
64
TK
Meat carriage guide spacer, 1
32
Carriage stop angle SS, welded
TK
Meat carriage angle plate only (DNS)
Meat carriage bearing SS
Thumb guard,nylon
Thumb guard nut SS
Thumb screw 1
4
-20
´
1
2
Item No.
A16200
A16220-1
AS16120
FW08S
FW15S
HHS075S
HN25S
LW15S
LW25S
Description
Carriage stop assembly, movable
Carriage stop assembly, fixed
Channel assembly, 37"
Flat washer, 3
8
SS
Flat washer, 1
2
SS
Hex head screw, 3
8
-16
´ 1
1
Hex nut, 3
8
-16 SS
Lock washer,
5
16
Lock washer, 3
8
SS
SS
4
SS
21
Item No.
S16120
S200B1
S360CB-1
16200
16220-1
310
311
311-1
376
Description
Channel, 37" SS
Carriage stop stud SS
Carriage bolt,
3
8
-16
´ 1
1
Carriage stop, movable
Carriage stop, fixed
4
SS
Waved washer
Rubber bumper, fixed stop
Rubber bumper, movable stop
Drive screw 10
´
1
2
SS
OPTIONAL 3334 EZ FLOW MEAT CARRIAGE & CHANNEL
Item No.
A16155EZ
A175S
FW05S
AN15S
HN30S
LW20S
S155-11
S155-R
S155EZ
Description
Meat carriage assembly complete – EZ Flow
Thumb guard assembly
Flat washer,
Acorn nut, 1
1
4
SS
4
-20 SS
Hex nut, 3
8
-16 light jam SS
Lock washer 3
8 regular SS
Meat carriage stop thumb screw
Raw meat carriage top only (DNS)
Meat carriage top only (NSS)
Item No.
S155EZ-3
16155EZ
16155EZ-1
16155-13
16155AEZ-1
16159
175S
175-1-S
175-2-S
Description
Hex stand-off, EZ Flow carriage
Meat carriage top & angle only
Meat carriage top only w/weld studs (DNS)
Carriage stop angle SS
Meat carriage angle plate
Meat carriage bearing SS
Thumb guard,nylon
Thumb guard nut SS
Thumb screw 1
4
-20
´
1
2
, SS
Item No.
A16200
A16220-1
AS16120EZ
FW08S
FW15S
HHS055S
HHS075S
HN25S
LW15S
LW25S
S16120
S200B1
S360CB-1
16200
16220-1
18120EZ-B3
310
311
311-1
376
Description
Carriage stop assembly, movable
Carriage stop assembly, fixed
Channel assembly, 37" – EZ Flow
Flat washer, 3
8
SS
Flat washer,
1
2
SS
Hex head screw,
Hex head screw,
5
3
16
-18
´ ¾ SS
4
SS
Hex nut,
3
8
-16 SS
8
-16
´ 1
1
Lock washer,
Lock washer,
5
16
3
8
SS
SS
Channel, 37" SS
Stop stud SS, guide bar & carriage stop
Carriage bolt, 3
8
-16
´ 1
1
Carriage stop, movable
Carriage stop, fixed
4
SS
Guide bar – EZ Flow
Waved washer
Rubber bumper, fixed stop
Rubber bumper, movable stop
Drive screw 10
´
1
2
SS
22
MODEL 3334, SERIES 4003
EZ FLOW CARRIAGE & CHANNEL
Item No.
A175S
A181155EZ
AN15S
FW05S
HN30S
LW20S
S155-11
S155EZ-1
S155EZ-2
Description
Thumb guard assembly
Meat carriage assembly, EZ Flow
Acorn nut,
1
4
-20
Flat washer,
Hex nut, 3
8
1
4
-16 light jam
Lock washer, light
Carriage stop thumb screw
Weld stud – NSS
Weld stud – NSS
Item No.
S181155AEZ
S18155EZ-1
S18155EZ
S18155EZ-R
S155EZ-3
16155-13
16159
175S
175-1-S
175-2-S
Description
Carriage bearing angle plate
Carriage top w/weld studs
Carriage top without weld studs
Raw meat carriage top only (DNS)
Hex stand-off
Carriage top angle SS
Carriage bearing
Thumb guard
Thumb guard nut
Thumb screw 1
4
-20
´
1
2
Item No.
A16200
A16220-1
AS1120EZ
FW08S
FW15S
HHS055S
HHS075S
HN25S
LW15S
LW25S
S1120EZ
16200
16220-1
18120EZ-B3
310
311
311-1
376
S200B1
S360CB-1
NOT SHOWN
S1007
Description
Carriage stop assembly, movable
Carriage stop assembly, fixed
Channel assembly, EZ Flow
Flat washer, 3
8
Flat washer, 1
2
Hex head screw, 5
Hex head screw,
3
16
-18
´
3
8
-16
´ 1
1
4
4
Hex nut, 3
8
-16
Lock washer,
Lock washer,
5
16
3
8
Channel, EZ Flow
Carriage stop, movable
Carriage stop, fixed
Carriage guide bar, EZ Flow
Waved washer
Rubber bumper, fixed stop
Rubber bumper, movable stop
Drive screw 10
´ ½ SS
Stop stud, SS
Carriage bolt, 3
8
-16
´ 1
1
4
Channel bracket, SS
23
— NOTES —
24
Motor
Mfg.
Doerr
Doerr
U.S. Motor
Doerr
U.S. Motor
Model
No.
XR72927
R72929
G54313
73020
G57016
USE WITH
Specifications
1 1
2
HP, 220/440-50/60-3 open
2HP, 220/440-50/60-3 open
2HP, 220/440-50/60-3 open
2HP, 550-60-3 open
2HP, 550-60-3 open
Motor
Mfg.
Doerr
U.S. Motor
Doerr
Baldor
Baldor
Baldor
Doerr
Baldor
Baldor
Baldor
Doerr
Doerr
U.S. Motor
Baldor
Baldor
Baldor
Doerr
Doerr
USE WITH
Model
No.
73032
G57347
72933
L3605
L3605-50
L1322T
67385
M3558T-5
M3558T-50
M3558T-8
72540
75425
G57011
M3611
M3611T-50
M3611T-8
73031
A907
Specifications
1
1
2
HP, 115/230-50-1 open
1
1
2
HP, 115/230-50-1 open
1
1
2
HP, 115/230-60-1 open
2HP, 115/230-60-1 TE
2HP, 115/230-50-1 TE
2HP, 115/230-60-1 open
2HP, 208/220/440-50/60-3 TE
2HP, 550-60-3 TE
2HP, 220/380/415-50-3 TE
2HP, 200-60-3 TE
3HP, 220/440-50/60-3 TE
3HP, 220/440-50/60-3 TE
3HP, 220/440-50/60-3 TE
3HP, 220/440-50/60-3 TE
3HP, 220/380/440-50-3 TE
3HP, 200-60-3 TE
5HP, 220/440-50/60-3 TE
5HP, 220/440-50/60-3 TE
Item No.
Description
A16547
Lower bearing housing assembly without wheel
A363
HN25
LW25S
S360CB-1
SSS05S
12251AL-
7
8
14544
14545
Lower bearing cup/cone assembly
Hex nut 3
8
-16, carbon-plated
Lock washer,
3
8
Carriage bolt,
8
3
8 heavy
-16
´ 1
1
Set screw, 10-24
´
3
DBL
Pulley, 9
´
7
Grease seal
8 double V
Retaining ring, internal
4
14548
14549
Grease seal
Bearing adj. cap
Item No.
Description
14740
Retaining ring – external
14746
T-handle lock, removable lower wheel
16251-11
´ 78AL Pulley, 11.4 ´
7
8
AL
16251-90X78AL Pulley, 9
´
7
8
16517
, al.
Inner race spacer
16543
16547
16560
Lower shaft, remov. wheel
Lower bearing housing
Lower wheel, 16", 6 spoke removable
16560DF
280
360A1
360B-1
Lower wheel, 16", 6 spoke removable – double flange
Lower shaft motor key
Grease fitting – angled
Set screw, ½-13 SS
25
A609AAW-16
SWITCH ASSEMBLY
Item No.
A16226A
A609AAW-16
H462
H462A
H462-1
HHS010S
HHS070S
HN10S
HN20S
LW15S
LW25S
16296-2
150
224
226-28
241BL
241WH
259
340
609AAW
Description
Green/red switch button assembly w/springs
Switch assembly, 1 & 3 ph less heater coils
Guard for switch toggle
Guard assembly for switch toggle
Trim ferrule, SS
Hex head screw, 10-32
´
3
Hex head screw, 3
Hex nut, 10-32 SS
8
8
SS
-16
´ 1 SS
Hex nut
5
16
-18 SS heavy
Lock washer
Lock washer,
5
16
3
8
SS regular
SS
Switch bracket SS
Conduit, 1
2
"
Conduit connector, 180°
Washer SS, 1 1
2
´
27
32
Wire, black, 12GA., CSA & UL
Wire, white, 12GA., CSA & UL
Anti-short busing ½"
Star lock washer
Manual switch, size 0, 1 & 3 ph
26
WATERTIGHT MAGNETIC SWITCH ASSEMBLIES
(AEG)
INCLUDES MOUNTING BRACKET AND WIRES
Item No.
Description
A22616AE-506
BAEG/PC-PB/C6, 1
1
2
HP,
208/220/230-50/60-3
A22616AE-514
BAEG/PC-PB/C8, 2HP,
208/220/230-50/60-3
A22616AE-516
BAEG/PC-PB/E4, 1 1
A22616AE-518
BAEG/PC-PB/D6, 1 1
2
HP, 440/460-3
2
HP, 380/415-50-3;
2HP, 380/415-50-3
A22616AE-520
BAEG/PC-PB/A23, 1 1
A22616AE-522
BAEG/PC-PB/C12, 1
1
2
HP, 104/115-50/60-1
2
HP & 3HP,
208/220/230-50/60-1
A22616AE-524
BAEG/PC-PB/A32, 2HP, 115-60-1
Item No.
Description
A22616AE-526
BAEG/PC-PB/C17, 2HP, 230-60-1
A22616AE-530
BAEG/PC-PB/F2.8, 2HP, 550-60-3
A22616AE-534
BAEG/PC-PB/E6, 3HP, 440/460-60-3
A22616AE-536
BAEG/PC-PB/D8, 3HP, 380/415-50-3
A22616AE-538
BAEG/PC-PB/F4, 3HP, 550-60-3
A22616AE-540
BAEG/PC-PB/C23, 5HP,
208/220/230-50/60-3
A22616AE-543
BAEG/PC-PB/E8, 5HP, 440-60-3
A22616AE-546
BAEG/PC-PB/D12, 5HP, 380/415-50-3
A22616AE-548
BAEG/PC-PB/F8, 5HP, 550-60-3
Item No.
Description
A16226A-SG
H462
H462A
H462-1
HHS070S
HN05S
HN20S
LW03S
LW15S
LW25S
RHS075S
16296-2
151
224-1
224-1F
224-1N
Green/red switch button assembly
Guard for switch toggle
Guard assembly for switch toggle
Trim ferrule S.S.
Hex head screw,
3
8
-16
´ 1 SS
Hex nut, 8-32 SS
Hex nut 5
16
-18 S.S.
Lock washer, #8 SS
Lock washer
Lock washer,
5
16
3
8
S.S.
heavy SS
Round head screw, 8-32
´
3
Switch bracket SS
Watertight conduit
Conduit connector, WT, 180°
SS
Conduit ferrule for watertight connector
Conduit nut for watertight connector
226AE-ENCL-PB Enclosure with button holes
226AE-0L02H
Overload, B17S-H (1.8-2.8)
4
226AE-0L04I
226AE-0L06K
226AE-0L08L
226AE-0L12M
226AE-0L17N
226AE-0L23O
226AE-0L32P
226AE-A0
226AE-C0
Overload, B17S-I (2.8-4)
Overload, B17S-K (4.6)
Overload, B17S-L (5.6-8)
Overload, B17S-M (8-12)
Overload, B17S-N (11-17)
Overload, B17S-O (15-23)
Overload, B17S-P (22-32)
Contactor, SP17.10-A0, 110V
Contactor, SP17.10-C0, 208/220/230V
27
Item No.
226AE-D0
226AE-E0
226AE-F0
226AE-506
226AE-514
226AE-516
226AE-518
226AE-520
226AE-522
226AE-524
226AE-526
226AE-530
226AE-534
226AE-536
226AE-538
226AE-540
226AE-543
226AE-546
226AE-548
226-28
241BL
241GR
241RD
241WH
297-1
42MC-Y73
42MC-Y74
Description
Contactor, SP17.10-D0, 380/415V
Contactor, SP17.10-E0, 440V
Contactor, SP17.10-F0, 550V
BAEG/PC-PB/C6
BAEG/PC-PB/C8
BAEG/PC-PB/E4
BAEG/PC-PB/D6
BAEG/PC-PB/A23
BAEG/PC-PB/C12
BAEG/PC-PB/A32
BAEG/PC-PB/C17
BAEG/PC-PB/F.28
BAEG/PC-PB/E6
BAEG/PC-PB/D8
BAEG/PC-PB/F4
BAEG/PC-PB/C23
BAEG/PC-PB/E8
BAEG/PC-PB/D12
BAEG/PC-PB/F8
Washer, 1 1
2
´
27
32
SS
Wire, black, 12 GA., CSA & UL
Wire, green, 12 GA ., CSA & UL
Wire, red, 12 GA., CSA & UL
Wire, white, 12 GA., CSA & UL
Wire terminal eyelet for 12 Ga. wire
Green start push button assembly
Red stop push button assembly
– 115 Volt with 7 Motor Leads –
Model 3334 Schematic Using 3-Pole Stromberg or AEG W.T. Switch for 115 Volts, Single Phase, 60 Cycle Baldor Motor with 7 Motor Leads
TO ELIMINATE BREAKING EFFECT OF MOTOR AFTER STOP IS ENGAGED
*To Reverse Rotation
Interchange Leads 5 & 8
– 115 Volt with 6 Motor Leads –
Model 3334 Schematic Using 3-Pole Stromberg or AEG W.T. Switch for 115 Volts, Single Phase, 60 Cycle Baldor Motor with 6 Motor Leads
TO ELIMINATE BREAKING EFFECT OF MOTOR AFTER STOP IS ENGAGED
*To Reverse Rotation
Interchange Leads 5 & 8
28
– 230 Volt with 7 Motor Leads –
Model 3334 Schematic Using 3-Pole Stromberg or AEG W.T. Switch for 230 Volts, Single Phase, 60 Cycle Baldor Motor with 7 Motor Leads
TO ELIMINATE BREAKING EFFECT OF MOTOR AFTER STOP IS ENGAGED
*To Reverse Rotation
Interchange Leads 5 & 8
– 230 Volt with 6 Motor Leads –
Model 3334 Schematic Using 3-Pole Stromberg or AEG W.T. Switch for 230 Volts, Single Phase, 60 Cycle Baldor Motor with 6 Motor Leads
TO ELIMINATE BREAKING EFFECT OF MOTOR AFTER STOP IS ENGAGED
*To Reverse Rotation
Interchange Leads 5 & 8
29
– 208/220/440 WITH 3 PHASE MOTOR –
Model 3334 Schematic Using 3-Pole Stromberg or AEG W.T. Switch for 208-220/440 Volts, Three Phase, 60 Cycle US or Baldor Motor
Item No.
Description
AN15S
FW05S
FW07S
FW08S
FW10S
FW15S
HHS003S
HHS005S
HHS010S
HHS015S
HHS020S
HHS025S
HHS035S
HHS040S
HHS049NL
HHS050S
HHS055S
HHS060S
HHS070S
HHS075S
Acorn nut, 1
Flat washer,
4
-20, SS
1
4
, SS
Flat washer,
Falt washer, 3
Flat washer,
3
8
8
, SS
ID
´ 1OD, SS
5
16
, SS
Flat washer, 1
2
, SS
Trimmed hex head screw,
8
32
Hex head screw, 10-32
´
3
8
8
´
1
, SS
Hex head screw,
32
´
1
2
, SS
Hex head screw, 10-32
´
7
Hex head screw, 1
8
8
, SS
, SS
Hex head screw,
Hex head screw,
Hex head screw,
1
1
1
4
4
-20
´
3
4
-20
´
1
4
-20
´
5
4
-20
´
3
16
-18
´
1
2
8
, SS
, SS
4
, SS
2
, nylon
8
, SS
, SS
Hex head screw,
5
Hex head screw,
Hex head screw,
Hex head screw,
Hex head screw,
Hex head screw,
5
5
5
3
3
16
-18
´
5
16
16
-18
´ 1, SS
8
-18
´
3
4
, SS
-16
´ 1, SS
8
-16
´ 1
1
4
, SS
Hex nut, 8-32, SS
HN05S
HN10S
HN15S
HN20S
HN25
HN25S
HN30S
HN35S
LH663
LW05S
LW10S
LW15S
LW20S
Hex nut, 10-32, SS
Hex nut,
1
4
-20, SS
Hex nut,
Hex nut,
Hex nut,
Hex nut,
Hex nut,
5
3
3
16
-18, SS
8
8
´ 16
-16, SS
3
8
-16, light jam, SS
3
8
-16, SS
Left hand saw guard
Lock washer, #10, SS
Lock washer,
Lock washer,
Lock washer,
1
5
4
, SS
16
, SS
3
8
, regular, SS
LW25S
Lock washer, 3
8
, SS
M55-G54313-U
Motor, 2HP 208/220/440-50/60-3, open
M68-67385-D
Motor, 2HP, 208/220/440-50/60-3, TE
M701-G57011-U Motor, 3HP, 208/220/230/440-50/60-3, TE
RHS20S
RHS10S
Round head screw, 10-32
´ 1
1
Round head screw, 10-32
´
3
4
8
, SS
, SS
Item No.
RHS25S
RHS30S
S1007
S11
S1120EZ
S12214
S155-11
S155B
S155EZ-3
S16005C
S16006
S16007
S16015-1
S16120
S16217L
S16217LTP
S16217R
S16239-5
S16273
S16275
S16290
S16296-8
S16335X
S181155AEZ
S18155EZ-1
S189
S19
S200B1
S217C
S217E
S229
S235
S239-B30
S239-B40
S239-B41
S240
S244
S253
S262
30
Description
Round head screw,
Round head screw,
1
1
4
-20
´
3
4
-20
´
7
4
8
, SS
, SS
Channel bracket, SS (3334-4003 only)
Ratchet trigger
Channel, SS (3334-4003 only)
Platter bracket starting with S/N 24464*
Meat carr stop thumb screw
Meat carriage stop welded
Hex standoff, EZ flow carriage
Head, SS
Head door, SS
Channel bracket SS
Motor baseplate adjusting stud, SS
Channel stainless steel
Base door left panel SS, see page 23
Base door left tapered panel, SS, see page 23
Base door right hinged SS
Base, stainless steel
Meat gauge bracket SS
Meat gauge plate, SS
Cleaning unit stamping SS
Switch brkt Kroger 800S2SA4
Upper wheel hinge plate, SS
Meat carriage angle, EZ flow (3334-4003 only)
Carriage top w/weld studs (3334-4003 only)
Ratchet arm stud, stainless
Ratchet base, stainless
Stopstud gde bar & crg stp SS
Base door hinge pin long SS
Base door hinge pin short SS
Wheel cleaner arm torsion spring, SS
Taper pin, stainless, 4
´
3
4
Base foot welded, SS
Base leg, welded
Hex leg, adjustable
Ratchet trigger spring
Wheel cleaner arm stud SS
Upper wheel aligning screw, SS
Meat gauge release handle
Item No.
Description
S268
S295
S325
S360CB-1
S415D
S416
SSS05S
SSS15
SSS20
10-1
111AL
112-212
116-22
118
119A
119AFSC
130
131
14362
14544
14545
14548
14746
14GP
14GP-1
14TH
16275
16278
16296-2
16301
16302
16303
16313-100
16360
16361
16501
16502
16503
16508
16517
16543
16547
16560
16700
17-3
Stationary bar hdless screw, SS
Wheel cleaner arm, stainless
Wheel cleaner washer, SS
Carriage bit 3
8
-16
´ 1
1
4
Stainless stationary bar
SS
Platter locator weld pin, SS
Set screw, 10-24
´
3
Set screw, cup point, 5
Set screw, cup point,
Ratchet arm
8
, cup point, SS
3
16
-18
´
5
8
-16
´
3
8
16
Tension spring pin, ALI.
Waved washer, 21
64
ID, 5
8
Saw guide bar 22 inch
Tension spring plate
Saw guide stationary bar
OD
Saw guide stationary bar fish
Saw cleaner bracket, rear
Saw cleaner SS
Bearing adj. cap
Grease seal
Ret. ring, internal
Grease seal
T-handle lock, removable lower wheel
Head door hinge pin long 1
1
Head door hinge pin short 1 1
Head door hinge
2
4
16Z
16001
16003-6
16003U-6
16005
16005-1
16006
16015-10
16015-11
16015-12
16015-2
Lower gde brkt saw clnr holder
Upper main bearing spacer
Lower saw wheel 16 inch, 6 spoke
Upper saw wheel 16 inch, 6 spoke
Head, aluminum
Ratchet shield on head
Head door (use A16006)
Motor base plate, 1 ph
Mtr bseplt, spec. TE FRM145T, SS
Motor base plate, spec. Norway
Motor base plate stud nut
16015-3
16015-4
16112
16132
16154
16155
16155-13
16155-2A
16155-2B
16155-2C
Motor base plate wing nut
Motor base plate lock washer
Head door latch
Saw cleaner brkt holder rear
Table extension, SS
Meat carriage top & angle
Carriage stop angle SS
Meat carriage guide
Meat carriage guide spacer
Meat carriage guide spacer
Meat carriage bearing
Platter hold down clip
Platter neck guard, SS
Platter neck guard, England
Tension spring gauge
Carriage stop movable
1
64
1
32
16159
16163A
16163B
16163B-1
16197
16200
16212
16220-1
16226A-5
Platter latch
Carriage stop fixed
Switch button plate rivet
16226A-6
16226A-8
Switch button speed nut
Switch buttonhole filler plate
16232
Scrap bucket
16239-16
16251AL
16272
Base interlock plte, SS, England
Upper v-belt pulley 11.4
16251-90X78AL Upper pulley 9
´
7
8
Meat gauge gear rack
´ 1, aluminum
Replaced by A16278
Meat gauge arm
Switch bracket, SS
Name & model plate (Ser. No. required)
Saw blade 124 inch
Lower shaft nut
Operating manual
Lower bearing housing
Lower shaft
Motor mount, rubber, 1 ph
Motor mount washer, 1 ph
Motor mount bolt 3 inch, 1 ph
Motor mount star washer 1 ph
Inner race spacer
Lower shaft, removable wheel
Lower brg. hsg. removable wheel
Lower wheel, 16", 6 spoke, removable
Parts repair kit
Fngrlift wshr, 9
16
´ .276 ´ .104, use FW05S
MODEL 3334 PARTS NUMBERS AND DESCRIPTIONS (Cont.)
Item No.
272-14
277
280
296
296-3
300
310
311
311-1
324
324A
340
360A1
360B
362
374
259
260
264-1
264G
265
267
270
271AL
272-6-S
272-7
272-8
272-9
272-13
375
376
4-30AL
415D
416
513
530
601
602B
602AFSC
605
609AAW
653PC-E
653PC-SP
661-1
663
17211-22
17211-35
175-1-S
175-2-S
175S
18120EZ-B3
211D
221-(size)
226-28
228-2
230DL
231DL
234
237
238
239-B31-2
239-B32-AR
239-B34
S240
242R
247
248
249
252X
256P
256PM
6808-G
71-1
708
710
7810-G
*NOTE
Description
Finger lift shim .022
Finger lift shim .035
Thumb guard nut, SS
Thumb screw 1
4
-20
´
1
Thumb guard, nylon
2
Guide bar, EZ flow
Finger lift fastener bolt 3
8
-16
´ 1
3
V-belt
Cndt conctrwshr 1 1
Lwr sawguide wshr,
2
1
´
27
4
32
SS
´
7
8
´
Upper shaft seal, double lip
1
16
4
Lower shaft seal, double lip
Grease fitting upper wheel
Up shaft castellated lock nut
Up shaft castld lock nut washr
Pipe leg, aluminum, 6"
Pipe leg cap
Replaced by AS239-B30-B*
Ratchet trigger spring
Base door lock, right
Upper shaft
Upper wheel hub cap
Base door handle
Shaft lock nut
Safety pusher plate, compostn
Safety pusher plate, aluminum
Anti-short bushing,
Aluminum slide gib
1
2
Meat gauge hand wheel
Meat gauge hand whl groove pin
Meat gauge release spring
Meat gauge release cotter key
Meat gauge release pin
Meat gauge worm gear
Meat gauge bracket wing nut
Knob, 4-point, 5
16
-18
Cap nut,
5
16
Hex bolt, 5
16
-18, SS
-18
´ 2, SS
Hex bolt, meat gauge bracket
Castle nut, 5
16
-18, SS
Lower shaft key
Motor shaft key
Toggle switch bracket, 1 1
2
HP mtr
Sw brkt ACW, BCW, AAA1, TAA1, 2HP mtr & up
Lower shaft woodruff key
Washr move carr stp headdr lck
Rubber bumper
Rubber bumper
Motor shim 1
16
" thick
Motor shim 1
8
" thick
Star lock washer
Lower brg hsng angl grease fitting
Lower brg hsng tilt set screw
Lower bearing housing cap
Shell Cassida grease EPS-2
Drive screw, name & model plate
Drive screw #10
´
1
Motor pulley 5
Stationary bar
´
3
4
2
, SS
, aluminum
Platter locator weld pins (use S416)
Upper wheel hub gasket
Retaining ring (replaces 16001) 22164 on
Upper saw guide bracket
Saw guide, upper
Saw guide upper bracket, fish
Saw guide, lower blade back-up
General purpose switch, 1 & 3 ph
Warning label, English
Warning label, Spanish
Saw guard to head door
Saw guard on saw guide bar (if before S/N 12242, also supply #116-22 & #661-1)
Toggle switch, 1 ph
Upper wheel hinge bracket SS
Saw guard safety decal
Decal, “Blade Tension”
Toggle switch, 3 ph
Stainless steel (S12214) side platter kits available before Ser. No. 24464 — check with Biro Service
Dept.
31
COMPLETE ASSEMBLIES FOR MODEL 3334
Item No.
Description
AS1120EZ
Channel assembly w/center guide
(3334-4003 only)
AS16005
Head & door assembly
AS16006
AS16120
Head door assembly, SS
Channel assembly, SS
AS16273-275 Meat gauge assembly
AS16275
Meat gauge plate with release assembly
AS16290
Cleaning unit stamping assembly, SS
AS239-B30-B Bolt-on base foot & leg assembly w/fasteners
AS415D
Stationary bar assembly SS
A116-22AL
Saw guide bar assembly 22
² – aluminum
A116-22SS
Saw guide bar assembly 22
² – stainless
A130
Steel cleaner assembly
A16Z
Guide brkt saw cleaner assem
A16003U-6
Up wheel assem without hinge plate
A16003U335-6
Up wheel assem with hinge plate
A16005
A16006
A16014L
A16014U
A16112
Head & door assembly
Head door with hinge assem
Head door hnge assem, lwr, shrtpn
Head door hnge assem, upr, lngpn
Head door latch assembly
A16132
A16155
A16163-1
A16163-E
A16163-M
A16196
Steel cleaner assembly, rear
Meat carriage assembly
Stationary platter assembly
Stationary platter assembly, England
Platter assembly, Govt., Size 2
Tension spring assembly
Item No.
Description
A227
A249R
A260
A262
A295
A363
A415D
A602
A661-1
A71-1
A16200
A16220-1
Channel stop assem movable
Channel stop assembly fixed
Up shaft brg assem without wheel
A247-1
A16278
A16335X
A16360
A16361
A16547
Meat gauge plate assembly less release assembly
Hinge plate assembly
Lower bearing housing assembly
Lower shaft bearing assembly
Lower bearing housing assembly, removable wheel
A181155EZ
Meat carriage assembly w/center guide
A19-1
A175S
A211-AL
(3334-4003 only)
Ratchet assembly
Thumb guard assembly
A211-SS
Finger lift assembly, removable – aluminum
Finger lift assembly, removable – stainless
Up bearing cup/cone assembly
Base door handle assem, right
Aluminum slide gib assembly
Meat gauge release assembly
Wheel cleaner assembly
Lower bearing cup/cone assem
Stationary bar assembly
Saw guide assembly, upper
Saw guard on head door assembly
Upper wheel hinge bracket assembly
MODELS EQUIPPED WITH STAINLESS STEEL FABRICATED HEADS
Stainless steel heads became available (as optional equipment) starting with Ser. #23265. From Ser. #23265 to
Ser. #25059 and starting again with Ser. #36272, these stainless steel heads were mated to the base structure in the same fashion as the aluminum head using the Item #260 slide gib. From Ser. #25060 to Ser. #36251 the machined blocks were eliminated and the slide gibs redesigned to a dovetail configuration to secure the head.
(The Factory Does Not Recommend Field Conversions)
PARTS EXCLUSIVE TO 3334SS WITH OPTIONAL STAINLESS STEEL HEAD STRUCTURE
Item No.
S16005
S16005B
S16005C
Description
Head, SS, 1st design, ser. #23265 to Ser. #25059, replaced by
S16005C
Head, SS, 2nd design, Ser.
#25060 to Ser. #36251, (uses dovetail slide gibs) replaced by 1 ea. #S16005C and 2 ea. #260
Head, SS, current design, Ser.
#36272 to present, (uses #260 slide gibs)
Item No.
S16006
16260ZA
16662
Description
Head door, SS, all SS heads
Slide gib, dove tail type, Serial
#25060 to Ser. #36251, no longer available
Saw guard on saw guide bar, SS all SS heads
32
33
WARNING LABEL LOCATIONS
ON MACHINE
34
WARNING LABEL LOCATIONS
ON MACHINE
35
— NOTES —
36
OPERATOR’S SIGNATURE PAGE
MY SIGNATURE ATTESTS THAT I HAVE COMPLETELY READ AND UNDERSTAND THIS
MANUAL.
I REALIZE THAT THIS MACHINE, IF OPERATED CARELESSLY, CAN CAUSE
SERIOUS INJURY TO MYSELF AND OTHERS.
NAME (PRINT) SIGNATURE
SUPERVISOR’S
INITIALS
DATE
37
LIMITED WARRANTY:
WARRANTY: The BIRO Manufacturing Company warrants that Model 3334 Power Cutter will be free from defects in material and workmanship under normal use and with recommended service.
BIRO will replace defective parts, which are covered by this limited warranty, provided that the defective parts are authorized for return, shipping charges prepaid, to a designated factory for inspection and/or testing.
DURATION OF WARRANTY: The warranty period for all parts covered by this limited warranty is one (1) year from inspection/demonstration advised on the returned Warranty Registration card, or eighteen (18) months from original factory ship date, whichever occurs first, except as noted below.
PARTS NOT COVERED BY WARRANTY: The following are not covered by this limited warranty: steel saw cleaners, item number 131; wheel cleaners, item number 179; steel guide, item number
119A; upper saw guide, item number 602B; lower back guide, item number 605; nylon filler, item number 177. This limited warranty does not apply to machines sold as used, rebuilt, modified,or altered from the original construction in which the machine was shipped from the factory. (Water contaminated electrical systems are not covered under this limited warranty.) BIRO is not responsible for electrical connection of equipment, adjustments to switch components or any other electrical requirements, which must be performed only by a certified electrician.
BIRO is not responsible for service charges or labor required to replace any part covered by this limited warranty or for any damages resulting from misuse, abuse, lack of proper or recommended service.
EXCLUSION OF WARRANTIES AND LIMITATION OF REMEDIES: BIRO gives no warranties other than those expressly stated in this limited warranty. THE IMPLIED WARRANTY OF MER-
CHANTABILITY, THE IMPLIED WARRANTY OF FITNESS FOR PROCESSING FOOD PROD-
UCTS, AND ALL OTHER IMPLIED WARRANTIES ARE SPECIFICALLY EXCLUDED. BIRO IS NOT
LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, EXPENSES, OR LOSSES. THE
REMEDIES PROVIDED IN THIS BIRO LIMITED WARRANTY ARE PURCHASER’S SOLE AND EX-
CLUSIVE REMEDIES AGAINST BIRO.
REGISTRATION CARDS: You must sign, date and complete the warranty registration card supplied with each machine. The warranty card must be returned to The Biro Manufacturing Company for proper registration. If no warranty card is returned to BIRO, the warranty period will begin from the date the machine was originally shipped from the factory.
HOW TO GET SERVICE:
1. Contact the agency from whom you purchased the machine; or
2. Consult the yellow pages of the phone directory for the nearest authorized dealer; or
3. Contact BIRO Mfg. Company for the nearest authorized service entity (250 plus worldwide) in your area.
THE BIRO MANUFACTURING COMPANY
1114 Main Street
Marblehead, Ohio 43440-2099
Ph. 419-798-4451
Fax 419-798-9106
E-mail: [email protected]
Web: http://www.birosaw.com
ITEM No.: 16313-100
PTCT: Md 3334-100-11-04-28
38
advertisement