Schlage Primus Level 1, Level 1+, Level 2, Level 3, Level 4, Everest Primus Level 7, Level 8, Level 9, Primus XP Level 1, Level 1+, Level 2, Level 3, Level 4, Everest Primus XP Level 7, Level 8, Level 9 Primus Cylinder, Lockout Cylinder Service Manual
Below you will find brief information for Primus Level 1, Primus Level 1+, Primus Level 2, Primus Level 3, Primus Level 4, Everest Primus Level 7, Everest Primus Level 8, Everest Primus Level 9. The Primus cylinder is designed for small to medium size key systems and offers a variety of features to help keep your property safe and secure. The cylinder is available in a variety of levels, each with its own level of key control and exclusivity. Primus Level 1 cylinders are the most basic level and are available to any locksmith. Primus Level 1+ cylinders are only available to dealers who have signed a contract with Schlage and purchased the required minimum dollar amount of inventory. Primus Level 2 cylinders are assigned a time zone exclusive pair of side bittings. Primus Level 3 and 4 cylinders offer the highest level of key control and exclusivity on Classic keyways. Everest Primus Level 7, 8 and 9 cylinders are designed for large key systems and offer the highest level of security.
Advertisement
Advertisement
Table of Contents
Table of Contents
Introduction ������������������������������������������������������������������������������������������3
Key Systems ��������������������������������������������������������������������������������������3
Conversion Cylinders ������������������������������������������������������������������������3
Primus and Primus XP Compatibility �������������������������������������������������4
Everest Primus and Everest Primus XP Compatibility ����������������������4
Serviceability �������������������������������������������������������������������������������������4
Cylinder Differences ��������������������������������������������������������������������������4
Terminology �����������������������������������������������������������������������������������������5
Keyways ��������������������������������������������������������������������������������������������5
Key Control ����������������������������������������������������������������������������������������5
Cylinder Category ������������������������������������������������������������������������������5
Construction and Operating Principles ���������������������������������������������6
Cam and Tailpiece Differences ����������������������������������������������������������7
Full Size Interchangeable Core (FSIC) ����������������������������������������������7
UL437 ������������������������������������������������������������������������������������������������7
Lockout Cylinder ���������������������������������������������������������������������������������8
Pinning Rules ������������������������������������������������������������������������������������8
How it works ��������������������������������������������������������������������������������������8
Key Bitting and Pin Specifications ����������������������������������������������������9
Reading Keys �������������������������������������������������������������������������������������10
Standard Cuts����������������������������������������������������������������������������������10
Side Bit Cuts ������������������������������������������������������������������������������������10
Reading Finger Pins ��������������������������������������������������������������������������11
Overview of Levels ����������������������������������������������������������������������������15
Dealer Controlled Systems ��������������������������������������������������������������15
End User Exclusive Systems �����������������������������������������������������������15
Primus and Primus XP Level 1 ���������������������������������������������������������16
Primus and Primus XP Level 1+ �������������������������������������������������������17
Primus and Primus XP Level 2 ���������������������������������������������������������18
Primus and Primus XP Level 3 and 4 �����������������������������������������������19
Everest Primus and Everest Primus XP Level 7 �����������������������������20
Everest Primus and Everest Primus XP Level 8 �����������������������������21
Everest Primus and Everest Primus XP Level 9 �����������������������������22
Key Control Procedures: Dealer Controlled Systems ��������������������23
Identification Cards ��������������������������������������������������������������������������23
Restricted Key Order Form ��������������������������������������������������������������23
Issuing ID Cards ������������������������������������������������������������������������������23
Key Control Procedures: Dealer Controlled Systems ��������������������24
Managing Lost, Stolen or Invalidated Cards ������������������������������������24
Managing Key Blank Inventory ��������������������������������������������������������24
Key Control Procedures: End User Controlled Systems ���������������25
Signature Verification �����������������������������������������������������������������������25
Primus Signature Card ��������������������������������������������������������������������25
Primus Signature Card ��������������������������������������������������������������������25
Primus and Primus XP Keyways ������������������������������������������������������26
Primus and Primus XP Level 1 and Level 1+ Keyways �������������������26
Primus and Primus XP Level 2, 3 and 4 Keyways ���������������������������26
Everest Primus and Everest Primus XP Keyways ��������������������������26
Key-in-Knob/Key-in-Lever Cylinders �����������������������������������������������27
Schlage Lock Sets ���������������������������������������������������������������������������27
Corbin Russwin Lock Sets ���������������������������������������������������������������28
Sargent Lock Sets ���������������������������������������������������������������������������28
Yale Lock Sets ���������������������������������������������������������������������������������28
Mortise Cylinders ������������������������������������������������������������������������������29
Schlage L-Series (except L9060 outside) ����������������������������������������29
Schlage L9060 Outside and Other Straight Cam Applications ��������29
Adams Rite MS, 4070, 4500 and 4700 Series; Lori 4500 and Corbin
Russwin DL 3000 ����������������������������������������������������������������������������29
Concealed Shell Mortise Cylinders ��������������������������������������������������30
Schlage L-Series (except L9060 outside) ����������������������������������������30
Mortise Full Size Cylinders ���������������������������������������������������������������31
Schlage L-Series (except L9060 outside) ����������������������������������������31
L9060 Outside ���������������������������������������������������������������������������������31
Key-in-Knob/Key-in-Lever Full Size IC ��������������������������������������������31
Schlage L-Series (except L9060 outside) ����������������������������������������31
L9060 Outside ���������������������������������������������������������������������������������31
Deadlock Cylinders ���������������������������������������������������������������������������32
Cylinder Application Table ���������������������������������������������������������������32
Full Size Interchangeable Core �������������������������������������������������������32
Padlock and Cabinet Lock Cylinders �����������������������������������������������33
Rim Cylinders ������������������������������������������������������������������������������������34
Full Size IC Rim Cylinders and Housing ������������������������������������������34
Classic Primus Keys �������������������������������������������������������������������������35
Key Blanks ���������������������������������������������������������������������������������������35
Cut Keys ������������������������������������������������������������������������������������������35
Master Keys �������������������������������������������������������������������������������������35
Everest Primus Keys �������������������������������������������������������������������������36
Key Blanks ���������������������������������������������������������������������������������������36
Cut Keys ������������������������������������������������������������������������������������������36
Master Keys �������������������������������������������������������������������������������������36
Bulk Packs������������������������������������������������������������������������������������������37
Tailpieces �������������������������������������������������������������������������������������������38
Multiple Tailpiece Cylinders (MTC) ��������������������������������������������������38
Tools and Sales Support Items ��������������������������������������������������������39
Interpreting Box Labels ��������������������������������������������������������������������40
Three Parts to Key Control ���������������������������������������������������������������41
1� Key Issue Policies ������������������������������������������������������������������������41
2� Track Issued Keys with SiteMaster 200 ���������������������������������������41
3� Use Patented Keys ����������������������������������������������������������������������41
Ordering Primus ��������������������������������������������������������������������������������42
Cylinders������������������������������������������������������������������������������������������42
Cylinder Bulk Packs �������������������������������������������������������������������������42
Limited Warranty ��������������������������������������������������������������������������������43
Small Format Interchangeable Core (SFIC) Warranty ���������������������43
Additional Terms & Conditions ���������������������������������������������������������43
Forms ���������������������������������������������������������������������������������������������44-47
Primus Service Manual
Primus Service Manual
Introduction
Introduction
Key Systems
Schlage offers two distinct key systems with six different cylinder styles�
Classic is the original Schlage key system including the
Classic, Primus and Primus XP cylinder styles and offers two levels of key duplication restrictions�
Everest is the newer security key system including
Everest, Everest Restricted, Everest Primus and Everest
Primus XP cylinder styles and offers 3 levels of key duplication restrictions�
The newest key system is the “XP” family� These cylinders have a #7 side pin added to provide more combinating options as well as added security�
Conversion Cylinders
Primus cylinders are available to retrofit most popular commercial locks by Corbin Russwin, Sargent and Yale making it more simple to convert to a Primus key system�
•
• •
• • •
• • •
B)
•
(C)
• • •
• • •
•
•
•
• • •
•
•
• •
• •
• • • •
• •
•
•
•
3
Primus Service Manual
Introduction
Primus and Primus XP Compatibility
Primus and Primus XP cylinders can be incorporated into any system using classic keyways including master keyed systems with no adverse effects on the system’s expansion�
Everest Primus and Everest Primus XP
Compatibility
Everest Primus and Everest Primus XP cylinders can be incorporated into any system using the Everest keyway including master keyed systems with no adverse effects on the system’s expansion� This would include use with
Everest Open cylinders and Everest Restricted cylinders�
Serviceability
It is unnecessary to invest in any additional servicing equipment for pinning than what is needed to service conventional cylinders� The side bitting is cut into the key blanks at the factory and the keys are able to be combinated using standard key cutting equipment
Everest Compatibility
PR
IMUS
Everest Primus
Cylinder
Shallow cut to lift check pin
Will operate both cylinders
Lip to lift check pin
Conventional
Everest Cylinder
Lip removed to prevent Primus operation
Operates only coventional Everest Cylinder
Cylinder Differences
Keys and Key Bows
• The word “Primus” is stamped on the back of the key bow�
• Standard key is embossed on both sides�
Available embossed on only one side�
• Same shape as Classic
Keys with limited stamping space�
None
• The word “Primus” is stamped on the back of the key bow�
• Standard key is embossed on both sides�
Available embossed on only one side�
• Same shape as Classic
Keys with limited stamping space�
U�S� 7,159,424
• The word “Primus” is stamped on the front of the key bow�
• Standard key is embossed on one sides�
Plain bow available�
• 20% larger than Classic
Primus keys with a larger stamping area on key bow�
• The word “Primus” is stamped on the front of the key bow�
• Standard key is embossed on one sides�
Plain bow available�
• 20% larger than Classic
Primus keys with a larger stamping area on key bow�
U�S� Patents
ID Numbers
Key Sections
Stamping
Locksmith ID stamped on
Level 1+ Keys�
Optional
Locksmith ID stamped on
Level 1+ keys�
Optional
US 5,715,717, 5,809,816
ID numbers stamped on every key�
Standard� Key sections stamped on all keys and plugs�
Available for all sections and all levels�
US 5,715,717, 5,809,816,
7,159,424
ID numbers stamped on every key�
Standard� Key sections stamped on all keys and plugs
Available for all sections and all levels�
Master Keying*
Available for Level 2, 3, and 4 keying systems�
Available for Level 1+, 2, 3, and 4 keying systems�
(Nominal) Key
Thickness
�092” �092” �106” �106”
#7 Finger Pin
Available
No Yes No Yes
*Ordering Primus master keyed products is similar to ordering any other Schlage master keyed products with the one addition of the necessary Primus forms (Face sheet and signature form as needed)�
Primus Service Manual
4
Terminology
Terminology
Keyways
Classic
Schlage pin tumbler keyways which existed before
Everest keyways� Obverse is the name of the open family of keyways (C, E, etc�) and there are three other families of restricted keyways: Reverse, Numbered, and Quad�
Primus Cylinders
Schlage’s high security sidebar cylinder mechanism� Key control, geographical exclusivity, and pick resistance are standard� UL437 drill resistance is optional� Primus keys operate conventional cylinders�
Classic
Classic
Everest
Cylinders and keys which incorporate all new keyways with the patented undercut groove on the right side of the key section� C Family is the name of the open family of keyways� B Family (for SFIC) and D Family keyways are restricted�
Everest
Undercut Groove
Everest
Cylinder Mechanisms
Conventional Cylinders
Standard cylinders� Cylinders which incorporate a series of locking top pins�
Conventional
Classic Everest
Primus
Classic Primus and
Everest Primus
Key Control
Restricted Keyways
Special non-stock keyways set aside for limited use and a higher degree of key control�
A letter of authorization from the end user is required to process orders for these keys, blanks, and cylinders�
Open Keyways
Standard keyways available without any ordering formalities� C Family (Everest) and Obverse (Classic) keyways are open�
Cylinder Category
Full Size
Pertaining to cylinders (including interchangeable cores), keys, and keyways based on the industry standard plug diameter of about 1/2”� All Schlage cylinders except
SFIC are full size�
Small Format Interchangeable Core (SFIC)
A core completely interchangeable with Best and its other clones� No Primus version exists�
Pins, springs, keys and keyways are based on a plug diameter smaller than the standard 1/2”�
Full Size Examples SFIC Example
Full Size IC Key-in-Knob/Lever
5
Primus Service Manual
Construction and Operating Principles
Cam
Cam Screw
Springs
Top Pins
Master Pins (as needed)
Bottom Pins
Shell
Sidebar Springs
Sidebar
Key
Finger Pin Springs
Finger Pins
Construction and Operating Principles
The Primus/Primus XP cylinder is a conventional
Schlage cylinder with a few modifications� A sidebar and finger pins are added to the conventional cylinder to provide additional security�
When the key is inserted, each of the side bit cuts lifts the finger pin and rotates it so that the notches in the side bar align with the notches in the back of the finger pins�
The Primus/Primus XP key has a secondary bitting on the side of the blade to accommodate the finger pins�
When all notches on the side bar and back of the finger pins are aligned and the regular pins are aligned at the shear line the plug is free to rotate�
Locked Unlocked
Primus Service Manual
6
Cam and Tailpiece Differences
Construction and Operating Principles
The cams and tailpieces used in the Primus/ PrimusXP cylinders are different than conventional cams and tailpieces because of the location of the sidebar and finger pins�
UL437
Each Schlage cylinder is available in a standard configuration as well as with a UL437 option� The catalog numbers associated with a standard cylinder are
20-7XX while the catalog numbers associated with the
UL437 cylinder are 20-5XX�
The illustrations below are rear views of the mortise cylinder as well as the key-in-knob/key-in-lever cylinders showing the differences in screw and cap pin locations�
All Everest keyway cylinders use the Primus/ PrimusXP screw and cap pin location�
The UL437 Primus/ PrimusXP cylinders incorporate drill resistant components for additional security�
Conventional Classic Primus & Everest
Full Size Interchangeable Core (FSIC)
Schlage introduced its Full Size Interchangeable
Core (FSIC) in 1984� Like the key-in-knob/key-inlever cylinders, the core uses a cap pin and spring mechanism, but the cap pin also serves to drive the cam or tailpiece�
Housings and tailpieces manufactured before the
Primus core was introduced only had clearance for the conventional cap pin� Now, all FSIC housings and tailpieces are made to accommodate both cap pin locations�
Current Design Pre-1992
7
Primus Service Manual
Lockout Cylinder
Lockout Cylinder
The Primus/Primus XP lockout cylinder is for use in applications in which it is necessary to temporarily disable the cylinder� It is essentially a very basic access control device�
The lockout cylinder utilized a standard 6-pin chamber row as well as a 4-pin chamber row with a special key�
NORMAL ROW
OF 6 CHAMBERS
How it works
Operating key turned to the Lockout Position
LOCKOUT ROW
ONLY HAS
FRONT 4 CHAMBERS
When the plug is in its standard operating position all keys will operate the lock� To temporarily disable to regular operating keys, the plug can be turned with the special key to align the bottom pins with the lockout row of pins�
The operating key cannot be removed in the lockout position because the back two pins are unable to disengage from the key
Lockout Key Turned to the Lockout Position
NORMAL
OPERATION
LOCKOUT
MODE
Pinning Rules
1� The fifth cut must be at least a #3 depth and the sixth cut must be equal to or deeper than the fifth cut�
2� Lockout cylinders must NOT be master keyed� When keys are inserted quickly, master pins may remain in the shell� This could cause a lockout, trap an operating key, or just prevent further operation of the cylinder�
The last two notches in the key are removed allowing the key to exit the cylinder�
Operating Key Entering in Lockout Position
The operating key cannot enter the cylinder because the back two pins are not able to settle into their bitting spaces on the key�
Primus Service Manual
8
Key Bitting and Pin Specifications
Key Bitting and Pin Specifications
These specs are the same for all
Schlage Classic, Primus ® , Primus ®
XP, Everest ® and Everest full size keyways.
® XP
1.012"
.8558"
.6996"
.5434"
.3872"
.231"
100°
MACS = 7
Increment:
Progression:
Blade Width:
Depth Tolerance:
Spacing Tolerance:
.015”
Two Step
.343”
+.002”-0”
±.001”
Root Depths
1 2 3 4 5 6
.031"
0 .335”
1 .320”
2 .305”
3 .290”
4 .275”
5 .260”
6 .245”
7 .230”
8 .215”
9 .200”
Cuts are read and written bow to tip.
The Primus side bitting is a patented process done at the Schlage factory.
Key blanks come with the side bitting already milled.
Size
6
7
4
5
8
9
2
3
0
1
Bottom Pins
Length
.165”
.180”
.195”
.210”
.225”
.240”
.255”
.270”
.285”
.300”
Part No.
34-300
34-301
34-302
34-303
34-304
34-305
34-306
34-307
34-308
34-309
Pins, Springs, etc.
Size
2
7
8
9
5
6
3
4
Master Pins
Length
.030”
.045”
.060”
.075”
.090”
.105”
.120”
.135”
Part No.
34-202
34-203
34-204
34-205
34-206
34-207
34-208
34-209
Size
1
2
3
Length
.235”
.200”
.165”
Finger Pins
Size
5
6
7
3
4
1
2
Part No.
34-001
34-002
34-003
34-004
34-005
34-006
34-058
Top Pins
Part No. Application
34-101
34-102
34-103
Plug total = 0, 1, 2, 3
Plug total = 4, 5, 6
Plug total = 7, 8, 9
Other Pins and Springs
Description
Tumbler spring
Finger pin spring
Cap pin
Cap pin spring
Sidebar
Sidebar spring
Part No.
C503-113
C603-951
C503-116
C503-115
C603-950
C603-952
9
Primus Service Manual
Reading Keys
Reading Keys
All keys will have exactly six Standard cuts and five Side
Bit cuts, which should be read from the bow of the key to the tip�
2 3 6 2 5
L C R L R
2 3 6 2 5
Standard Key Cuts
Side Bit Cuts
Standard Cuts
Standard key cuts should be read using the Schlage Key
Gage (40-104)� Insert key into widest end and slide until key stops� The nearest number is the key cut depth�
L C R L R
Notches Aligned
Each of the side cuts raise and swivel the finger pin in order to align the notch in the pin to the notch in the side bar�
If a side cut is misread, the pin will misalign with the side bar by being too high, too low or rotated in the wrong direction�
2 3 6 1 2
L C R L R
2 3 6 1
2
L C R L R
Cut is too low Rotated incorrectly and
Cut is too high
Side Bit Cuts
There are six side bit cut possibilities for Primus and
Everest Primus and seven side bit cut possibilities for
Primus XP and Everest Primus XP�
1
2
3
4
5
6
Primus ® and Everest ® Primus ®
1
2
3
4
7
5
6
Primus ® XP and Everest ® Primus ® XP
Primus Service Manual
10
Reading Finger Pins
Reading Finger Pins
Learning to read finger pins is useful because pins can get spilled or mixed in with other size finger pins�
In 1998 the bottom of the finger pin was redesigned�
This does not affect the functionality of the pins or the technique used for reading the pins�
Step 1: Determine the Angle
Left Center Right
Step 3: Convert Angle and Depth to Numbers
Deep
Shallow
Extra Shallow
Left
2
1
Right
6
5
7
Center
4
3
Tweezers
Step 2: Determine the Depth
Left and Right
Shallow Deep
(ref�)
Shallow
Center
Deep
(ref�)
Extra Shallow
Right
(ref�)
XP Products Only
11
Primus Service Manual
Keying Instructions
High Security Cylinders
Tools for Rekeying K
J
1
A
E
End Cap Removal Tool
Plug Follower
B
D
C
Pinning Knife
Loading Rod
N
P
M
180˚
F
L
Keying Instructions
3
G
H
A. Key
B. Plug
C. Bottom Pins
D. Top Pins
E. Top Pin Springs
F. Shell
G. Cap Pin Spring
H. Cap Pin
J. Tail Piece
K. End Cap
L. Side Bar
M. Side Bar Springs
N. Finger Pin Springs
P. Finger Pins
2 Plug Holder
Maintain Pressure on side bar
Primus Service Manual
12
4
Determine Bottom Pinning
8
180˚
If plug doesn't rotate, change one or more finger pins
9
5
Determine Finger Pin Bitting
Centers of Conventional Cuts
1
2
3
4
7
5
6
1
2
3
4
7
5
6
1
2
3
4
7
5
6
1
2
3
4
7
5
6
1
2
3
4
7
5
6
1
2
3
4
7
5
6
Centers of Finger Pin Chambers
6
Operating Key
Use in Master Keying
Key cut to all #9 depths
Setup Key
Place a small amount of fine grain graphite into pin chambers after inserting pins.
10
Determine Top Pinning
Total Bottom Pins and Master Pins Top Pin Length
0, 1, 2, 3 1 .235
4, 5, 6
4, 5, 6
2
3
.200
.165
11
7 b
12 a
13
Primus Service Manual
13
Pinning Knife a b
14 b a
15
16
17
18
Maintain pressure on side bar
19 a
Maintain pressure on side bar
45˚ b
Maintain pressure on plug face while removing key
20
45˚
Primus Service Manual
14
Overview of Levels
Overview of Levels
Below is a chart that provides an overview and comparison of the different Key Control levels� In-depth information is covered in the pages following�
Dealer Controlled Systems
Dealer controlled systems are sold and serviced by the locksmith or dealer who sold the system� End users must order keys and request servicing through the original dealer�
End User Exclusive Systems
End User Exclusive Systems are sold directly to and controlled by the end user� The systems are generally sold to larger businesses or those that need a very high level of security� Side bit milling is exclusive to the end user based on either random assignment, the first
2 digits of the zip code, time zone or on a nationwide basis�
LEVEL 2
LEVEL 3
LEVEL 4
LEVEL 1
LEVEL 1
+
National Non-Exclusive
Stocked by distributors and resold to end users via commercial locksmiths;
All Level 1 Locksmiths have the same side bittings.
Primus XP Dealer
Wholesaler/ Exclusive
Locksmith
Exclusive
Locksmiths resell wholesaaler’s side bitting to end users; keys bear locksmith ID number.
Owned and stocked by dealers then resold to end users. Keys bear unique ID based upon first three digits zip-code exclusivity of side bitting.
Dealer Exclusive
Owned and stocked by dealers then resold to end users. Keys bear a unique
ID based upon time-zone exclusivity of side-bitting.
End User Exclusive
Exclusivity is based on either random assignment or on the first 2 digits of the
zip code, depending on end user commitment.
End User Exclusive
Exclusivity is based on either a time
zone or nationwide basis, depending on end user commitment.
Typical Applications
• Strip Mall Shops
• Small Businesses
• Upscale Homes
• Small Businesses
• Restaurants
• Doctor's Offices
• Office Buildings
• Banks
• Private Schools
• Healthcare Residences
Consider Everest Open for
Commercial Exclusivity
Primus
Wholesaler/
Locksmith
Exclusive
Locksmiths resell wholesaaler’s side bitting to end users; keys bear locksmith ID number.
XP Dealer
Exclusive
Owned and stocked by dealers then resold to end users. Keys bear unique ID based upon first three digits zip-code exclusivity of side bitting.
Dealer Exclusive
Owned and stocked by dealers then resold to end users. Keys bear a unique
ID based upon time-zone exclusivity of side-bitting.
End User Exclusive
•
•
Educational Facilities
Healthcare Facilities
•
•
Large Office Complexes
Government Buildings
• Detention Centers
• Franchises
Exclusivity is based on either random assignment, on the first 2 digits of the zip code, on time zone, or on a nationwide basis, depending on end user commitment.
LEVEL
7
LEVEL 8
LEVEL
9
15
Primus Service Manual
Primus and Primus XP Level 1
Primus and Primus XP Level 1
•
•
•
•
Overview for End User
•
•
Level 1 is designed for small to medium size businesses�
Keys cannot be duplicated at hardware stores or mall key stands�
ID cards are issued from originating locksmith�
Keys available from any Level 1 dealer in the country by presenting the proper identification and the key to be duplicated�
All keys must be cut by a security dealer�
End user does not have access to key blanks�
Keyways and Keying Options
Level 1 is primarily for upgrading users of C or E keyway
•
• conventional cylinders, so CP and EP are the principle keyways at this level� However, the other five keyways are available through some distributors�
• Level 1 is not appropriate for large key systems�
• The side bittings chosen for Level 1 keys limit master key systems to one keyway�
• Multi-section key blanks cannot be made because of the incompatible side bittings of the lower level keys�
Level 1 cylinders are shipped 0-bitted�
All keying is done in the field�
•
•
•
Overview for Locksmith or Security Dealer
• Easy introduction to Primus and Primus XP sales�
•
Same side bitting nationwide�
No minimum order required�
No sole source relationship with your distributor or customers�
Level 1 contract required with each distributor used to purchase products�
Sequence Numbers
The sequence number is a 4-digit code which identifies the combination of side bitting + keyway� Since the side bittings of Level 1 are shared by all dealers nationwide, there is only one sequence number per keyway� The sequence number can be used to distinguish inventory for dealers and distributors who stock more than one level of Primus�
•
•
•
•
•
As covered in the contract, it is important for a Level 1 dealer: to safeguard Primus and Primus XP key blanks not to give, sell or lend key blanks to anyone under
• any circumstances to sell directly to end users only to issue a Level 1 ID card to each end user to require ID card and signatures before duplicating any Level 1 keys to maintain accurate records of all keys�
Side Bitting 62266
Sequence # Section
1001 CP
1002
1003
EFP
FGP
Side Bitting 62766
Sequence # Section
1001 CP
1002
1003
EFP
FGP
Primus Number
(First six digits) identifies the distributor who sold this side bitting to the locksmith.
Sequence Number
Last four digits identify the keyway and side bitting.
red stripe
1234561001 1
000001
1
Color Stripe
Level One ID cards have a red stripe which matches the stripe on the
Level One cylinder box.
Embossed Level Number
Card Serial Number
Allows the locksmith to maintain records on valid and invalid cards.
Side Bitting 62422
Sequence # Section
1004 CEP
1005 FP
Side Bitting 62422
Sequence # Section
1006 EP
Side Bitting 22473
Sequence # Section
1004 CEP
1005
1006
FP
EP
Color Stripe
Level One ID cards have a red stripe which matches the stripe on the
Level One cylinder box.
Primus Number
(First six digits) identifies the distributor who sold this side bitting to the locksmith.
123456
ABC LOCKSMITH CO.
123456 000001
Locksmith ID Number
Six digits assigned to each Level One Plus locksmith by Schlage.
This number is stamped on all One Plus key blanks at the factory.
Locksmiths are only permitted to make keys corresponding to cards with their own ID number.
Dealer Name
Card Serial Number
Allows the locksmith to maintain records on valid and invalid cards.
000001
Primus Service Manual
16
Primus and Primus XP Level 1+
Primus and Primus XP Level 1+
•
•
•
Overview for End User
•
•
•
•
•
Designed for small to medium size key systems�
Limits availability of keys to one specific locksmith company�
Only the company that maintains the key records and key issue authorizations for the end user’s system can cut the keys�
End user receives an ID card from the originating locksmith�
End user presents ID card to the locksmith together with signature card to obtain additional keys�
All keys bear the locksmith’s 6-digit ID number�
No other locksmiths are permitted to cut keys�
End user does not have access to key blanks�
•
•
Primus Level 1+ wholesalers stock 0-bitted cylinders with their side combination� Primus XP Level 1+ wholesalers can stock subassembled bulk, KA, KD�
Key blanks are shipped from Schlage and invoiced through the wholesaler�
Becoming a Level 1+ Dealer
To become a Level 1+ dealer, sign the appropriate contract with your wholesaler and purchase the prevailing minimum dollar amount of inventory� Dealer’s ability to sell high security products and provide end user service must be reviewed and approved by a Schlage
SSC sales manager�
•
•
•
•
Overview for Locksmith or Security Dealer
• Ties end users to dealer for their Primus and Primus
•
XP systems�
Primus Level 1+ Locksmith tied to wholesaler for key blanks� Primus XP Level 1+ Locksmith can purchase key blanks from any wholesaler and will be given side bitting exclusivity based on the first 3 digits of locksmith’s zip code�
Key blanks stamped with dealer ID number�
Classic Wholesaler has its own side bitting and selects which of its dealers will handle the product�
Keys bear a unique ID based upon side-bitting�
Other locksmiths in the area may have the same side bitting, but are not authorized to cut keys with other dealer’s ID number�
Primus Number
(First six digits) identifies the distributor who sold this side bitting to the locksmith.
Sequence Number
(Only appears on cards manufactured before 12/96.)
Last four digits identify the keyway and side bitting.
orange stripe
1234561100 1 1 PLUS
ABC LOCKSMITH CO.
123456 000001
Locksmith ID Number
Six digits assigned to each Level One Plus locksmith by Schlage.
This number is stamped on all One Plus key blanks at the factory.
Locksmiths are only permitted to make keys corresponding to cards with their own ID number.
Color Stripe
Level One Plus ID cards have an orange stripe which matches the stripe on the One Plus cylinder box.
Level Number
Dealer Name
Card Serial Number
Allows the locksmith to maintain records on valid and invalid cards.
Color Stripe
Level One Plus ID cards have an orange stripe which matches the stripe on the One Plus cylinder box.
Primus Number
(First six digits) identifies the distributor who sold this side bitting to the locksmith.
123456
ABC LOCKSMITH CO.
123456 000001
Locksmith ID Number
Six digits assigned to each Level One Plus locksmith by Schlage.
This number is stamped on all One Plus key blanks at the factory.
Locksmiths are only permitted to make keys corresponding to cards with their own ID number.
Dealer Name
Card Serial Number
Allows the locksmith to maintain records on valid and invalid cards.
As covered in the contract, it is important for a Level 1+ dealer:
• not to cut keys for any other Primus and Primus XP
Level 1+ systems as identified by the ID number on
•
• each key� to safeguard Primus and Primus XP Level 1+ key blanks and ID cards not to give, sell or lend key blanks to anyone under
•
• any circumstances� to require and validate a signature before duplicating any Level 1+ keys to maintain accurate records of all keys cut�
Keyways and Keying Options
•
•
•
•
•
Level 1+ is not appropriate for large key systems�
Key blanks are not available to institutional locksmiths
Side bittings for Level 1+ limit systems to one keyway�
Multi-section key blanks cannot be made because of the incompatible side bittings of the lower level keys�
Primus Level 1+ cylinders are shipped 0-bitted�
Primus XP Level 1+ can be shipped 0-bitted, KA,
KD, MK and bulk packed�
Sequence Numbers
The sequence number is a 4-digit code which identifies the combination of side bitting + keyway� Since virtually every Schlage wholesaler and Locksmith carrying
Primus XP Level 1+ product has a different side bitting and some carry more than one, the sequence number can be useful to separate inventory on the shelf when that inventory had the same keyway buy different side bittings� At Level 1+, each sequence number is assigned to one specific wholesaler�
17
Primus Service Manual
Primus and Primus XP Level 2
Primus and Primus XP Level 2
•
•
Overview for End User
•
•
•
•
•
•
Designed for medium to large size key systems�
Availability of keys is limited to one specific hardware dealer�
End user enters into a sole source relationship with the dealer
The original dealer is the only one that can supply keys�
End user receives and ID card from the original dealer�
End user presents ID card together with signature to obtain additional keys�
End user does not have access to key blanks�
No other hardware dealers or locksmiths in the area have access to blanks with the dealer’s side bitting�
Overview for Locksmith or Security Dealer
• Requires a substantial inventory buy-in�
•
•
•
•
Ties all end users to dealer for Primus and Primus
XP Level 2 keys�
Dealer must provide key duplication and cylinder service because end user cannot go elsewhere for keys�
Each dealer is assigned a time zone exclusive pair of side bittings�
No two dealers in the same time zone will have the same side bittings�
Level 2S
This side bitting is assigned to the dealer for KA and KD stock, and key systems the dealer generates in the field�
Dealer must maintain all records for these systems�
Becoming a Level 2 Dealer
To become a Level 2 dealer, simply sign the appropriate contract with Schlage and purchase the prevailing minimum dollar amount of inventory� Dealer’s ability to sell high security products and provide end user service must be reviewed and approved by a Schlage SSC sales manager�
•
•
As covered in the contract, it is important for a Level 2 dealer:
• to safeguard Primus and Primus XP Level 2 key blanks and ID cards
•
• not to give, sell or lend key blanks to anyone under any circumstances� to require and validate a signature before duplicating any Level 2 keys to maintain accurate records of all keys cut� to not make any Level 2 keys for systems generated by dealers in other time zones who may have the same side bitting�
Keyways and Keying Options
The geographical exclusivity of Level 2 makes it
•
• impractical to illustrate or list all the side bittings� New ones are being issued every day around the country�
• The dealer is responsible for all key bittings and key control measures�
Multi-section keys are available for this level�
The LP blank is made of stainless steel and cannot be cut on most key machines in the field� Therefore, most customers should order cut keys rather than blanks�
Primus Number
(First six digits) identifies the dealer.
Sequence Number
(Only appears on cards manufactured before 12/96.)
Last four digits identify the keyway and side bitting.
yellow stripe
1234562001 2
THE SAMPLE BUILDERS CO.
2
0 0 0 0 0 1
Color Stripe
Level Two ID cards have a yellow stripe which matches the stripe on the Level Two cylinder box.
Embossed Level Number
Dealer Name
Card Serial Number
Allows the dealer to maintain records on valid and invalid cards.
Primus Number
(First six digits) identifies the dealer.
Primus Service Manual
18
Color Stripe
Level Two ID cards have a yellow stripe which matches the stripe on the Level Two cylinder box.
123456
THE SAMPLE BUILDERS CO.
0 0 0 0 0 1
Dealer Name
Card Serial Number
Allows the dealer to maintain records on valid and invalid cards.
Primus and Primus XP Level 3 and 4
Primus and Primus XP Level 3 and 4
•
•
Overview for End User
•
•
•
•
•
•
Schlage’s highest level of key control and exclusivity on Classic keyways�
Levels 3 and 4 use the same authorization procedures�
Levels 3 and 4 differ only by the amount of geographical exclusivity purchased�
End user has access to key blanks and cuts keys�
End user generates and maintains their own key system�
A signed original Primus Face Sheet and signature card are required initially to set up End User Level systems�
Every subsequent order must include a signed original Face Sheet which is closely checked for an authorized signature� No faxes or photocopies are acceptable because of the ease of forgery�
End user can get competitive bids and order End
User Level material from any one of a large number of authorized dealers nationwide�
The degree of geographical exclusivity of end user side bitting is determined with the initial order as listed below�
Level 3U
Fewer than 60 Cylinders
Schlage randomly assigns a side bitting from a small pool of combinations which may be repeated locally�
There are no guarantees of geographical exclusivity�
Overview for Locksmith or Security Dealer
• These levels are for end users who want to cut their
•
•
• own keys and/or generate their own key system�
Dealers already selling Level 2 or 8 are authorized to sell Level 3 and 4 products
Level 1+ and 7 dealers must sign an additional key control contract, but there is no buy-in required�
Degree of geographical exclusivity is determined by the end user’s commitment to cylinder volume and separate exclusivity purchases�
Keyways and Keying Options
The geographical exclusivity of these levels makes it
•
• impractical to illustrate or list all the side bittings� New ones are being issued every day�
Dealers cannot stock this level
All cylinders, keys and blanks are shipped to the end
•
• user’s designated location�
Multi-section keys are available for this level, so it will accommodate larger systems�
In the Obverse keyway family, the end user can use up to six keyways� Larger systems must either be broken up or furnished in Quad restricted keyways� (Restricted means that Schlage requires a letter of authorization from the end user even for conventional keys and blanks on these key sections�)
Level 3G (Geographical)
More than 60 cylinders
Schlage assigns an exclusive side bitting based on the first two digits of the end user’s zip code�
Level 4Z (Time Zone)
Minimum of 2000 cylinders over two years or pay a fee�
End user buys exclusivity of one side bitting within his time zone and country�
Level 4N (Nationwide)
Minimum of 4000 cylinders over two years or pay a fee�
End user buys nationwide exclusivity of one side bitting�
19
Primus Service Manual
Everest Primus and Everest Primus XP Level 7
Everest Primus and Everest Primus XP Level 7
•
•
•
Overview for End User
•
•
•
•
•
•
Designed for small to medium sized key systems�
Availability of keys is limited to one specific locksmith company�
End user enters into a sole source relationship with a commercial locksmith company�
The original supplier is the only company that can supply additional keys�
End user receives an ID card for the originating locksmith�
Present ID card and signature to obtain additional keys�
All keys bear the locksmith’s six-digit ID number�
End user does not have access to key blanks�
No other locksmiths are permitted to cut keys�
Becoming a Level 7 Dealer
To become a Level 7 dealer, sign the appropriate contract with the wholesaler and purchase the prevailing minimum dollar amount of inventory� Dealer’s ability to sell high security products and provide end user service must be reviewed and approved by a Schlage SSC sales manager�
As covered in the contract, it is important for a Level 2 dealer:
• not to cut keys for any other Everest Primus and
Everest Primus XP Level 7 systems as identified by
• the ID number on each key� to safeguard Everest Primus and Everest Primus XP
•
•
•
Level 7 key blanks and ID cards not to give, sell or lend key blanks to anyone under any circumstances� to require and validate a signature before duplicating any Level 7 keys to maintain accurate records of all keys cut�
Overview for Locksmith or Security Dealer
• Everest Primus Level 7 Locksmith tied to wholesaler
•
•
• for key blanks� Everest Primus XP Level 7 Locksmith can purchase key blanks from any wholesaler and will be given side bitting exclusivity based on the first
3 digits of locksmith’s zip code�
Other locksmiths in the area may have the same side bitting�
Everest Primus Level 7 wholesalers stock 0-bitted cylinders with their side combination� Everest Primus
XP Level 7 can be ordered KA, KD and MK�
Key blanks are shipped to dealer from Schlage and invoiced through the wholesaler�
Keyways and Keying Options
Everest Open C family keyways are now Schlage’s default keyways for new commercial key systems as well as for more commercial stock product� At Level
7, all Everest C family keyways are available, allowing integration into any existing system using these new
Schlage keyways, as well as the ability to begin new C family key systems�
Primus Number
Six digits identifies the distributor who sold this side bitting to the locksmith.
Locksmith ID Number
Six digits assigned to each Level 7 locksmith by Schlage.
This number is stamped on all Level 7 key blanks at the factory.
Locksmiths are only permitted to make keys corresponding to cards with their own ID number.
Dealer Name
Card Serial Number
Allows the locksmith to maintain records on valid and invalid cards.
The last cut of the side bittings at this level is always shallow (1, 3 or 5) to raise the check pin of conventional
Everest cylinders�
• Level 7 is not appropriate for key systems where the
•
• end user needs to cut keys on site�
Key blanks are not available to institutional locksmiths�
Level 7 cylinders are shipped 0-bitted, KA, KD, MK or bulk packed�
Primus Number
Six digits identifies the distributor who sold this side bitting to the locksmith.
123456
THE SAMPLE LOCKSMITH CO.
654321 000001
Locksmith ID Number
Six digits assigned to each Level 7 locksmith by Schlage.
This number is stamped on all Level 7 key blanks at the factory.
Locksmiths are only permitted to make keys corresponding to cards with their own ID number.
Dealer Name
Card Serial Number
Allows the locksmith to maintain records on valid and invalid cards.
Primus Service Manual
20
Everest Primus and Everest Primus XP Level 8
Everest Primus and Everest Primus XP Level 8
•
•
Overview for End User
•
•
•
•
•
•
Designed for small to large size key systems�
Availability of keys is limited to one specific hardware dealer�
End user enters into a sole source relationship with the dealer
The original dealer is the only one that can supply keys�
End user receives and ID card from the original dealer�
End user presents ID card together with signature to obtain additional keys�
End user does not have access to key blanks�
No other hardware dealers or locksmiths in the area have access to blanks with the dealer’s side bitting�
Overview for Locksmith or Security Dealer
• Requires a substantial inventory buy-in�
•
•
•
•
Ties all end users to dealer for Everest Primus and
Everest Primus XP Level 8 keys�
Dealer must provide key duplication and cylinder service because end user cannot go elsewhere for keys�
Each dealer is assigned one time zone exclusive side bitting�
No two dealers in the same time zone will have the same side bittings�
Becoming a Level 8 Dealer
To become a Level 8 dealer, simply sign the appropriate contract with Schlage and purchase the prevailing minimum dollar amount of inventory� Dealer’s ability to sell high security products and provide end user service must be reviewed and approved by a Schlage SSC sales manager�
•
•
•
•
As covered in the contract, it is important for a Level 8 dealer:
• to safeguard Everest Primus and Everest Primus XP
•
Level 8 key blanks and ID cards not to give, sell or lend key blanks to anyone under any circumstances� to sell directly to end users only to require and validate a signature before duplicating any Level 2 keys to maintain accurate records of all keys cut� to not make any Level 2 keys for systems generated by dealers in other time zones who may have the same side bitting�
Keyways and Keying Options
The geographical exclusivity of Level 8 makes it impractical to illustrate or list all the side bittings� New ones are being issued every day around the country�
• The last cut of side bittings at this level is always shallow (1, 3 or 5) to raise the check pin of
•
• conventional Everest cylinders�
With the ten Everest C family keyways available, large key systems are possible�
Unlike Level 2, each Level 8 dealer is assigned
• one side bitting and the corresponding sequence numbers�
There is no differentiation between factory and fieldoriginated systems�
LEVEL
8
Primus Number
Six digits identifies the dealer.
123456
THE SAMPLE HARDWARE CO.
000001
Dealer Name
Card Serial Number
Allows the dealer to maintain records on valid and invalid cards.
Primus Number
Six digits identifies the dealer.
123456
THE SAMPLE LOCKSMITH CO.
000001
Dealer Name
Card Serial Number
Allows the dealer to maintain records on valid and invalid cards.
21
Primus Service Manual
Everest Primus and Everest Primus XP Level 9
Everest Primus and Everest Primus XP Level 9
•
•
Overview for End User
•
•
•
•
•
•
Schlage’s highest level of key control and exclusivity on Everest keyways�
Level 9 is subdivided to be flexible for the amount of geographical exclusivity purchased��
Side bit milling is assigned to the end user based on the exclusivity purchased� See level and commitments listed below�
End user has access to key blanks and cuts keys�
End user generates and maintains their own key system�
A signed original Primus Face Sheet and signature card are required initially to set up End User Level systems�
Every subsequent order must include a signed original Face Sheet which is closely checked for an authorized signature� No faxes or photocopies are acceptable because of the ease of forgery�
End user can get competitive bids and order End
User Level material from any one of a large number of authorized dealers nationwide�
•
•
Overview for Locksmith or Security Dealer
• These levels are for end users who want to cut their
•
•
•
•
• own keys and/or generate their own key system�
Dealers already selling Level 2 or 8 are authorized to sell Level 9 products
Level 1+ and 7 dealers must sign an additional key control contract, but there is no buy-in required�
Degree of geographical exclusivity is determined by the end user’s commitment to cylinder volume and separate exclusivity purchases�
No ID cards are issued at this level�
All authorization is done with the Primus Face Sheet and Signature Card�
Schlage requires an original signature on a Primus
Face Sheet to process each order�
Unless Level 9 side bitting is bought outright,
Schlage reviews cylinder volume annually and, if the contractual commitment is not met, has the option to lower the project to Level 9U and place the side bitting into the Level 9U pool for other end users
The degree of geographical exclusivity of end user side bitting is determined with the initial order as listed below�
Level 9U (Universal)
Fewer than 60 Cylinders
Schlage randomly assigns a side bitting from a small pool of combinations which may be repeated locally�
There are no guarantees of geographical exclusivity�
Level 9G (Geographical)
More than 60 cylinders
Schlage assigns an exclusive side bitting based on the first two digits of the end user’s zip code�
Keyways and Keying Options
The geographical exclusivity of these levels makes it impractical to illustrate or list all the side bittings� New ones are being issued every day�
• Dealers can stock bulk-pack sub-assembled cylinders�
•
•
All cylinders, key and blanks are shipped to the end user’s designated location�
Multi-section keys are available for this level, so it will accommodate larger systems�
• The last cut of the side bittings at this level is normally shallow (1, 3 or 5) to raise the check pin of conventional Everest cylinders� However, side bittings with a deep last cut are also available at
Level 9, provided that the key system will never incorporate conventional cylinders�
Level 9Z (Time Zone)
Minimum of 2000 cylinders over two years or pay a fee�
End user buys exclusivity of one side bitting within his time zone and country�
Level 9N (Nationwide)
Minimum of 4000 cylinders over two years or pay a fee�
End user buys nationwide exclusivity of one side bitting�
Keyways and Keying Options
Everest D family restricted keyways are also available at
Level 9� Use these keyways when patented key control is also required for the conventional (non-Primus) keys on the job�
Schlage does not publish full details on the Everest D family restricted keyways for security reasons� However, the keyway structure is the same as that of the C family keyways�
The Everest D family key section can be cut on Schlage
Everest D key punch (40-099) or rotary key cutting machine�
Primus Service Manual
22
Key Control Procedures: Dealer Controlled Systems
Key Control Procedures: Dealer Controlled Systems
Identification Cards
The dealer is responsible for stocking ID cards for levels
1, 1+, 2, 7 and *8 and verifying all authorized signatures to issue new keys as key blanks are not permitted to be sold to end users�
The card for each level bears a unique colored stripe, varying forms of dealer information and a signature panel on the back� When receiving an order for new keys, it is the responsibility of the dealer to verify the signature on the back of the card�
Restricted Key Order Form
The Restricted Key Order Form is available for no charge and makes the process of tracking keys very easy� If used with a manual credit card machine, the form is able to be imprinted with the numbers embossed on the card and provides space to complete the number of keys requested as well as the key symbol or bitting� The end user receives one copy for his records and the dealer retains a copy in his records�
ID Cards
(Order in multiples of 50)
40-061 Level 1
Level 1+
Level 2
Everest Primus
*Specify level 7 or 8
40-065
40-062
40-060*
123456
000001
ID Cards
(Order in multiples of 50)
40-061-XP Level 1
Level 1+
Level 2
Everest Primus
*Specify level 7 or 8
40-065-XP
40-062-XP
40-060-XP
Issuing ID Cards
It is recommended that the dealer consistently uses one of the following procedures for issuing ID cards to their end user customers�
1� Issue a card to each end user or authorized signatory� The end user must keep the card and present it each time a key is requested� Verify the signature with the back of the card and verify the validity of the card in the log book�
2� Issue a card to each end user or authorized signatory� Keep all signed cards in a secure location with the key records� Verify the signature with the back of the card and validity of the card in the log book each time a key is requested�
3� When multiple signatures are required, use the
Primus Signature Card� This can be used in addition to or instead of ID cards for the Dealer Levels�
However, this method should not be used with Level
1 as the end user may request keys from any Level
1 dealer�
23
Primus Service Manual
Key Control Procedures: Dealer Controlled Systems
Key Control Procedures: Dealer Controlled Systems
Managing Lost, Stolen or Invalidated Cards
Each ID card has a unique serial number in the lower right corner� If a card is reported lost or stolen or a business changes authorized personnel and a previously authorized card holder refuses to surrender his card, the dealer must make a notation in his log that the card is no longer valid to obtain keys�
Checking the card serial number in the log book and verifying signatures should be part of every key authorization�
Managing Key Blank Inventory
It is important to keep an accurate record of key blank inventory as well as a detailed log of keys issued to customers in case a question arises from an end user or law enforcement agency�
Each incoming order of Primus blanks should be logged with a transaction on a Restricted Key Order Form, signed and dated by the employee who received and counted the blanks�
All miscuts should also be documented on one of the these forms, signed and dated by the employee who handled the transaction and logged into the main book�
The total number of key blanks received, minus miscuts and keys issued, should always equal the number still on hand� The dealer should reconcile the log periodically and also log and discrepancies at that time�
Discrepancies may indicate a breach in security or simply a careless employee�
Primus Control Register
MS-E160
While this form is not required, dealers should use this form or originate their own forms to track key issues, miscuts, key blank shipments received and track discrepancies�
Primus Service Manual
24
Key Control Procedures: End User Controlled Systems
Key Control Procedures: End User Controlled Systems
Signature Verification
The authorization for the end user levels is performed at the Schlage Key Control Center� The dealer is responsible for submitting the end user’s signed forms to
Schlage with each order�
Primus Signature Card
The Primus Face Sheet form is located in the back of this manual and is required for every Primus or Primus
XP factory order�
Primus Signature Card
The Primus Signature Card is found at the back of this manual and should be used to register each project and its authorized signatories with the factory�
Faxes and Photocopies
Levels 3, 4 and 9 are the highest levels of key control�
For this reason, no faxed or photocopied signatures will be accepted by the Primus Key Control Center�
The dealer should complete the form with the end user
(job) name, street address and zip code� The zip code is used for maintaining the varying degrees of geographical exclusivity offered at the end user levels and should be accurately translated�
It is permissible to fax or photocopy the blank forms in order to speed up the authorization process when the end user has no blank forms� However, once the page is signed it becomes an original and cannot be faxed or photocopied, then submitted for an order�
It is also possible to order a supply of blank forms at no charge using the following form numbers:
There is space for up to five authorized signatures on the signature card� All signatures will have equal authority to order locks, keys, key blanks and cylinders unless otherwise noted� The signature at the top of the list has authority to add and delete signatures from the card, so it is important that the appropriate person is the top signer�
Signature Card
Face Sheet
MS-E130
MS-E120
25
Primus Service Manual
Primus and Primus XP Keyways
Primus and Primus XP Keyways
Primus and Primus XP Level 1 and Level 1+ Keyways
P
R I MUS
P
R I MUS
P
R I MUS
P
R I MUS
P
R I MUS
P
R I MUS
Keyway CP CEP EP EFP FP FGP
Primus and Primus XP Level 2, 3 and 4 Keyways
Stainless Steel
All-Section Key
LP
HP
Multi-Section Keys
JP
PR
IMUS
PR
IMUS
PR
IMUS
PR
IMUS
PR
IMUS
PR
IMUS
CP CEP EP EFP FP
Everest Primus and Everest Primus XP Keyways
FGP
All-Section Key
C000
C100
Multi-Section Keys
C200
C150
Multi-Section Keys
C120
Multi-Section Keys
C230
C134 C145 C135
New master key systems begin here and expand to the right�
C125 C124 C123
Stock keyway for commercial sales�
C234 C235 C245 C345
Primus Service Manual
26
Key-in-Knob/Key-in-Lever Cylinders
Key-in-Knob/Key-in-Lever Cylinders
The part numbers for assembled Classic Primus and Everest Primus cylinders are the same� Adding the keyway suffix to the part number determines which cylinder will be shipped� To order any of the XP products, simply add the suffix “-XP” to the end of the complete cylinder number� For example, “20-793-XP C123” is the proper way to order and Everest Primus XP cylinder with a C123 keyway�
ND AL
D A
A
ORB
Levers
Everest
& Primus
Classic
Vertical
Knobs
Horizontal
Everest
& Primus
Classic
S-Series
Everest
& Primus
Classic
Schlage Lock Sets
Series Design
A, H Except Orbit
A, H
AL
D Knobs
D Knobs
ND Levers
S, S200
Orbit
All
All
Standard Door
Thickness
All
Thick Door
2”-2Z\x”
All
All
Cylinder
Mechanism
Classic Primus
Classic Primus UL
Everest Primus
Everest Primus UL
Classic Primus
Classic Primus UL
Everest Primus
Everest Primus UL
Classic Primus
Classic Primus UL
Everest Primus
Everest Primus UL
Classic Primus
Classic Primus UL
Everest Primus
Everest Primus UL
Classic Primus
Classic Primus UL
Everest Primus
Everest Primus UL
Classic Primus
Classic Primus UL
Everest Primus
Everest Primus UL
Classic Primus
Classic Primus UL
Everest Primus
Everest Primus UL
Complete
Cylinder
20-724
20-524
20-724
20-524
20-724-122
20-524-122
20-724-122
20-524-122
20-728
20-528
20-728
20-528
20-748
20-548
20-748
20-548
20-724
20-524
20-724
20-524
20-765
20-565
20-765
20-565
20-752
20-552
20-752
20-552
Tailpiece
A301-337
A301-337
A301-337
A301-337
N523-022
N523-022
N523-022
N523-022
S605-231
S605-231
S605-231
S605-231
A301-337
A301-337
A301-337
A301-337
A301-338
A301-338
A301-338
A301-338
A700-031
A700-031
A700-031
A700-031
C603-524
C603-524
C603-524
C603-524
Plug
33-158
33-154
33-135
33-221
33-158
33-154
33-135
33-221
33-158
33-154
33-135
33-221
33-158
33-154
33-135
33-221
33-158
33-154
33-135
33-221
33-158
33-154
33-135
33-221
33-158
33-154
33-135
33-221
Shell
A201-683
A201-683
A201-683
A201-683
A201-683
A201-683
A201-683
A201-683
A201-683
A201-683
A201-683
A201-683
A201-683
A201-683
A201-683
A201-683
A201-683
A201-683
A201-683
A201-683
A201-683
A201-683
A201-683
A201-683
A201-683
A201-683
A201-683
A201-683
NOTE: To order any of the XP products, simply add the suffix “-XP” to the end of the complete cylinder number�
27
Primus Service Manual
Key-in-Knob/Key-in-Lever Cylinders
Key-in-Knob/Key-in-Lever Cylinders
Corbin Russwin Lock Sets
Side View Description
CL3300
CL3400
CL3600
CK4200
UT5200
(since 1963)
Cylinder
Mechanism
Classic Primus
Classic Primus UL
Everest Primus
Everest Primus UL
Classic Primus
Classic Primus UL
Everest Primus
Everest Primus UL
Classic Primus
Classic Primus UL
Everest Primus
Everest Primus UL
Sargent Lock Sets
B520-407
Washer
7l, 8l, 10
Line Levers
7, 8, 9
Line
Knobs
6 Line
Except
B Knob
Classic Primus
Classic Primus UL
Everest Primus
Everest Primus UL
Classic Primus
Classic Primus UL
Everest Primus
Everest Primus UL
Classic Primus
Classic Primus UL
Everest Primus
Everest Primus UL
Yale Lock Sets
A501-783
Blocking Disc
5300LN
5400LN
Levers
5300
5400
6200
Knobs
Classic Primus
Classic Primus UL
Everest Primus
Everest Primus UL
Classic Primus
Classic Primus UL
Everest Primus
Everest Primus UL
20-719
20-519
20-719
20-519
20-720
20-520
20-720
20-520
20-726
20-526
20-726
20-526
20-747
20-547
20-747
20-547
20-723
20-523
20-723
20-523
Complete
Cylinder
20-762
20-562
20-762
20-562
20-739
20-539
20-739
20-539
20-727
20-527
20-727
20-527
Tailpiece Plug
N523-022
33-158
33-154
33-135
33-221
A301-338
—
33-158
33-154
33-135
33-221
33-158
33-154
33-135
33-221
Shell
A201-683
A201-683
A201-690
C604-243
C303-437
Assembly with cap
C604-243
33-163
33-162
33-224
33-225
33-163
33-162
33-224
33-225
33-163
33-162
33-224
33-225
A201-683
A508-637
A508-638
A301-043
B520-409
33-163
33-162
33-224
33-225
33-163
33-162
33-224
33-225
A201-683
A201-683
NOTE: To order any of the XP products, simply add the suffix “-XP” to the end of the complete cylinder number�
Primus Service Manual
28
Mortise Cylinders
Mortise Cylinders
Schlage L-Series (except L9060 outside)
L583-254
Classic
Cam
Cylinder Only
Description
L583-153
Everest & Primus
Cylinder Only:
L & N
Escutcheons
Cylinder With Compression
Ring & Spring:
Rose Trim
Cylinder with Compression Ring & Spring
Cylinder
Mechanism
Classic Primus / Everest Primus
Classic Primus / Everest Primus UL
Classic Primus / Everest Primus
Classic Primus / Everest Primus UL
Lockout Controlled Access
Lockout Controlled Access UL
Schlage L9060 Outside and Other Straight Cam Applications
B502-191
Classic
B502-498
Everest & Primus
Cylinder Only:
L & N
Escutcheons
Classic Primus / Everest Primus
Classic Primus / Everest Primus UL
Cylinder With Compression
Ring & Spring:
Rose Trim
Classic Primus / Everest Primus
Classic Primus / Everest Primus UL
Lockout Controlled Access
Lockout Controlled Access UL
Adams Rite MS, 4070, 4500 and 4700 Series; Lori 4500 and Corbin Russwin DL 3000
B502-292
Classic
B502-944
Everest & Primus
Cylinder With Compression
Ring & Spring:
Lockout Controlled Access
Lockout Controlled Access UL
20-718
20-518
B502-380
Classic
B502-945
Everest & Primus
Cylinder with
C|, ” Blocking Ring
Classic Primus / Everest Primus
Classic Primus / Everest Primus UL
Classic Primus / Everest Primus
Classic Primus / Everest Primus UL
20-706
20-506
20-708
20-508
Cylinder Only
20-701
20-501
20-700
20-500
20-715
20-515
Complete
Cylinder
20-793
20-593
20-787
20-500
20-715
20-517
NOTE: To order any of the XP products, simply add the suffix “-XP” to the end of the complete cylinder number�
29
Primus Service Manual
Concealed Shell Mortise Cylinders
Cams for Schlage Primus Mortise Cylinders to Operate Other Manufacturers’ Locks
Cam Description
B520-366 Corbin Russwin © DL4000 Series (Old Corbin 420 and Russwin 1503)
Previously known as XB11-656
B520-309 Corbin Russwin © ML2200 Series (Old Corbin 7000-9000 and Russwin 4000-5000)
All functions except ML2255 and ML2242 inside
Previously known as XB11-629
B520-367 Corbin Russwin © residential Locks
A65 ML2200 master ring deadbolt functions manufactured before 6/10/93 and old Russwin cast iron
Previously known as XB11-887
B520-329 Yale © 2160, Arrow © #004, Sargent © 13-0660 (All functions except 16 inside and 50 outside)
Previously known as XB11-631
Concealed Shell Mortise Cylinders
Schlage L-Series (except L9060 outside)
Cam Description
L583-254
Classic
L583-153
Everest & Primus
Cylinder Only:
L & N
Escutcheons
Cylinder
Mechanism
Classic Primus / Everest Primus
Classic Primus / Everest Primus UL
NOTE: To order any of the XP products, simply add the suffix “-XP” to the end of the complete cylinder number�
Primus Service Manual
30
Complete
Cylinder
20-799
20-599
Mortise Full Size Cylinders
Mortise Full Size Cylinders
Cylinder Only Cylinder with
Compression
Ring & Spring
Cylinder with
Blocking Ring
Schlage L-Series (except L9060 outside)
Cam Description
Complete
Cylinder
20-798
L583-255
Cylinder with
Compression Ring
& Spring:
L & N Escutcheons
Cylinder
Mechanism
Classic Primus/
Everest Primus
Cylinder with
Compression Ring,
Spring and C\,”
Blocking Ring:
Rose Trim
Classic Primus/
Everest Primus
20-776
Schlage L-Series (except L9060 outside)
Cam Description
Complete
Cylinder
20-798
L583-255
Cylinder with
Compression Ring
& Spring:
L & N Escutcheons
Cylinder
Mechanism
Classic Primus/
Everest Primus
Cylinder with
Compression Ring,
Spring and C\,”
Blocking Ring:
Rose Trim
Classic Primus/
Everest Primus
20-776
L9060 Outside L9060 Outside
Cam Description
Cylinder
Mechanism
Classic Primus/
Everest Primus
Complete
Cylinder
20-782
Cam Description
K510-680
Cylinder with
Compression Ring
& Spring:
L & N Escutcheons
Cylinder with
Compression Ring,
Spring and Z\x”
Blocking Ring:
Rose Trim
Classic Primus/
Everest Primus
20-783
L583-255 Cylinder with
Compression Ring,
C\zn ” & C\,”
Blocking Rings
NOTE: To order any of the XP products, simply add the suffix “-XP” to the end of the complete cylinder number�
Key-in-Knob/Key-in-Lever Full Size IC
L583-255 Cylinder with
Compression Ring,
C\zn ” & C\,”
Blocking Rings
Description
Classic Primus / Everest Primus Core
Classic Primus / Everest Primus Core less logo
Classic Primus Plug
Everest Primus Plug
Retainer Cap
Cap Pin
Cap Pin Spring
Actuating Ring
Actuating Pin
Control Pin
Cylinder
Mechanism
Classic Primus/
Everest Primus
Classic Primus/
Everest Primus
Complete
Cylinder
20-766
20-722
Part Number
20-740
20-741
33-160
33-139
C503-118
C603-827
C503-115
C603-956
C603-964
C603-967
31
Primus Service Manual
Deadlock Cylinders
Deadlock Cylinders
Single Cylinder Double Cylinder
Cylinder Application Table
Function
B761, B764
B861, B864
B761, B764
B861, B864
B760, B763
B860, B863
B762
B862
B762
B862
Door
Thickness
1C\,” – 2”
Over 2”– 2Z\x”
1 C\,” – 2Z\x”
1C\,” – 2”
Over 2”– 2Z\x”
Cylinder
Mechanism
Classic Primus
Everest Primus
Classic Primus UL
Everest Primus UL
Classic Primus
Everest Primus
Classic Primus UL
Everest Primus UL
Classic Primus
Everest Primus
Classic Primus UL
Everest Primus UL
Classic Primus
Everest Primus
Classic Primus UL
Everest Primus UL
Classic Primus
Everest Primus
Classic Primus UL
Everest Primus UL
Full Size Interchangeable Core
B250, H and S200-Series
Complete
Cylinder
20-742
Tailpiece and
Retainer Pack
B610-082
20-542
20-745
20-545
20-746
20-546
20-743
20-543
20-744
20-544
B610-083
B610-084
B610-085
B610-086
Description
Classic Primus Everest Primus
Outside
20-784
Plug
33-158
33-135
33-154
33-221
33-158
33-135
33-154
33-221
33-158
33-135
33-154
33-221
33-158
33-135
33-154
33-221
33-158
33-135
33-154
33-221
Shell
A201-683
A201-683
A201-683
A201-683
A201-683
Inside
20-785
NOTE: To order any of the XP products, simply add the suffix “-XP” to the end of the complete cylinder number�
Primus Service Manual
32
Padlock and Cabinet Lock Cylinders
Padlock and Cabinet Lock Cylinders
Series
CL
KS/KC
Variation
Door
Drawer
Key in Knob/
Key in Lever
FSIC
Cylinder
Mechanism
Classic Primus
Everest Primus
Classic Primus UL
Everest Primus UL
Classic Primus
Everest Primus
Classic Primus UL
Everest Primus UL
Classic Primus
Everest Primus
Classic Primus UL
Everest Primus UL
Classic Primus
Everest Primus
Door Drawer Padlock
Complete
Cylinder
20-772
Actuator or
Driver
20-572
20-774
20-574
20-744
20-574
20-740
CL10-360
KZ32DA0
Plug
33-158
33-135
33-154
33-221
33-158
33-135
33-154
33-221
33-158
33-135
33-154
33-221
33-160
33-139
Shell
A201-683
NOTE: To order any of the XP products, simply add the suffix “-XP” to the end of the complete cylinder number�
33
Primus Service Manual
Rim Cylinders
Rim Cylinders
Vertical Tailpiece (No� 1 bar) Horizontal Tailpiece (No� 2 bar)
Description
Rim cylinder, vertical tailpiece
Rim cylinder, horizontal tailpiece
Rim cylinder lockout
Cylinder Mechanism
Classic Primus / Everest Primus
Classic Primus / Everest Primus UL
Classic Primus / Everest Primus
Classic Primus / Everest Primus UL
Classic Primus / Everest Primus
Classic Primus / Everest Primus UL
Full Size IC Rim Cylinders and Housing
Description Part Number
Cylinder with Classic Primus / Everest Primus Core
Housing less core
20-757
20-079
Complete Cylinders
20-709
20-509
20-710
20-510
20-716
20-516
20-057
NOTE: To order any of the XP products, simply add the suffix “-XP” to the end of the complete cylinder number�
Primus Service Manual
34
Classic Primus Keys
35-157
Standard Front
Operating Keys Control Keys
Back of Both
PRIMUS
DO NOT DUPLICATE
PAT� NO� 7,159,424
35-158
Standard Front
CONTROL
Back of Both
PRIMUS
DO NOT DUPLICATE
PAT� NO� 7,159,424
Classic Primus Keys
Access Bows
Access Bow
35-114
Back
PRIMUS
35-052
Plain Front
CONTROL 35-053
Plain Front
Key Blanks
Part Number
35-157
35-053
35-171
35-158
35-052
35-172
35-159
Cut Keys
Part Number
48-157
48-053
48-171
48-158
48-052
48-152
48-159
Master Keys
Part Number
49-157
49-053
49-171
49-158
49-052
49-152
Description
Standard bow, embossed both sides
Standard bow, unembossed one side, “PRIMUS” logo on one side
Standard bow, stainless steel LP section key
Control key, standard bow, embossed both sides
Control key, standard bow, unembossed one side, “PRIMUS” logo on one side
Control key, stainless steel LP section key
Lockout key, standard bow, embossed both sides
Description
Standard bow, embossed both sides
Standard bow, unembossed one side, “PRIMUS” logo on one side
Standard bow, stainless steel LP section key
Control key, standard bow, embossed both sides
Control key, standard bow, unembossed one side, “PRIMUS” logo on one side
Control key, stainless steel LP section key
Lockout key, standard bow, embossed both sides
Description
Standard bow, embossed both sides
Standard bow, unembossed one side, “PRIMUS” logo on one side
Standard bow, stainless steel LP section key
Control key, standard bow, embossed both sides
Control key, standard bow, unembossed one side, “PRIMUS” logo on one side
Control key, stainless steel LP section key
NOTE: To order any of the XP products, simply add the suffix “-XP” to the end of the complete cylinder number�
35
Primus Service Manual
Everest Primus Keys
Everest Primus Keys
Operating Keys Control Keys
35-004
Standard Front
PRIMUS
DO NOT DUPLICATE
Pat� 5,809,816
Standard
Back
35-005
Standard Front
PRIMUS
DO NOT DUPLICATE
Pat� 5,809,816
Standard
Back
CONTROL
35-012
Plain
Both Sides
DO NOT DUPLICATE
Pat� 5,809,816
Key Blanks
Part Number
35-004
35-005
35-006
35-012
35-013
35-019
Cut Keys
Part Number
48-004
48-005
48-006
48-012
48-020
48-019
Master Keys
Part Number
49-004
49-005
49-012
49-020
35-013
Plain
Both Sides
DO NOT DUPLICATE
Pat� 5,809,816
6-Pin
Control
Lockout
6-Pin
Control
Lockout
6-Pin
Control
Lockout
6-Pin
Control
Lockout
6-Pin
Control
6-Pin
Control
Description
Standard bow, embossed one side
Control key, standard bow, embossed one side
Lockout key, standard bow, embossed one side
Standard bow, unembossed
Control key, standard bow, unembossed
Lockout key, standard bow, unembossed
Description
Standard bow, embossed one side
Control key, standard bow, embossed one side
Lockout key, standard bow, embossed one side
Standard bow, unembossed
Control key, standard bow, unembossed
Lockout key, standard bow, unembossed
Description
Standard bow, embossed one side
Control key, standard bow, embossed one side
Standard bow, unembossed
Control key, standard bow, unembossed
Back of Keys
(except unembossed)
Facility or
Dealer ID Number
001426
Section
NOTE: To order any of the XP products, simply add the suffix “-XP” to the end of the complete cylinder number�
Primus Service Manual
36
Bulk Packs
Bulk Packs
10-Piece Bulk Pack Key-in-Knob/Key-in-Lever Cylinders
Contents (10 each)
Cylinder
Mechanism
Loaded Shells
Plugs
Caps
Cap Pins
Cap Pin
Springs
Check Pins (Everest Conventional Only)
Check Pin Springs (Everest Conventional Only)
Primus/Primus XP
Primus/Primus XP
NOTES: 1�
2�
3�
Specify keyway and finish: 606 or 626�
Multiple tailpiece cylinders are not available for hotel function locks�
Primus key blanks must be ordered separately�
10-Piece Bulk Pack Mortise Cylinders
Loaded Shells
Plugs
Cam Screws
NOTES: 1�
2�
3�
Contents (10 each)
Cylinder
Mechanism
Primus/Primus XP Check pins (Everest Conventional Only)
Check Pin Springs (Everest Conventional Only)
Primus/Primus XP
Specify keyway and finish: 606 or 626�
Multiple tailpiece cylinders are not available for hotel function locks�
Primus key blanks must be ordered separately�
Keyway Type
Classic
Everest
Keyway Type
Classic
Everest
Bulk Pack
Number
09-833
09-764
Bulk Pack
Number
09-835
09-767
Bulk Pack Mortise Cylinder Cam and Collars
Keyway Type Descriptions
Classic Primus and Everest
Primus
Straight Cam
L-Series Cam
Adams Rite Kit
Compression rings and springs
*Specify finish: 605, 606, 612, 625, 626
Contents (10 each)
B502-948
L583-153
B502-944 cams, 36-079-037 blocking rings, B220-050 set screw packs
36-083
10-Piece Bulk Pack Rim Cylinders
Contents (10 each)
Loaded Shells
Plugs
Caps
Cap Pins
Collars
Tailpieces
Drivers
Cap Pin Springs
Screws & Back Plate Packs
Check pins (Everest Conventional Only)
Check Pin Springs (Everest Conventional
Only)
10-Piece Bulk Pack Interchangeable Cores
Contents (10 each)
Loaded Shells
Plugs
Caps
Cap Pins
Collars
Tailpieces
Drivers
Cap Pin Springs
Screws & Back Plate Packs
Check pins (Everest Conventional Only)
Check Pin Springs (Everest Conventional
Only)
Cylinder
Mechanism
Primus/Primus XP
Primus/Primus XP
Keyway Type
Classic
Everest
Cylinder
Mechanism
Primus/Primus XP
Primus/Primus XP
Keyway Type
Classic
Everest
Bulk Pack
Number
09-761
09-762
09-763*
09-419
Bulk Pack
Number
09-834
09-765
Bulk Pack
Number
09-836
09-766
37
Primus Service Manual
Tailpieces
Tailpieces
Cap Pin Location
Everest
& Primus
Classic
Conventional
Levers
D
Tailpiece Orientation
AL D A
A
ORB
A73
ORB
Knobs
Vertical
Horizontal
A201-934
A73 ORB Knob
A301-337 for A, H
A301-338
A, H
ORB Knobs
A700-031
A, AL, H
D (for 2"-2¹⁄₂" doors)
C604-243
D Levers
C603-524
D Knobs
Use with this driver
B502-310
For both knob and lever applications
Multiple Tailpiece Cylinders (MTC)
Keyways
Primus ALL Keyways
(Classic and Everest)
Contents
(1) Pre-assembled cylinder 0-bitted, less tailpiece and keys
(1) A301-337 tailpiece, A and H-Series (except Orbit)
(1) A301-338 tailpiece, A and H-Series Orbit
(1) A700-031 tailpiece, AL-Series
(1) C603-524 tailpiece, D-Series Knobs
(1) N523-022 tailpiece, ND-Series Levers (black)
(2) C503-115 cap pin springs
(2) C503-116 cap pins
Primus Service Manual
38
Part Number
40-700
Controlled Access
40-500
UL437 Listed
Tools and Sales Support Items
Finger Pin Kit
40-070
Pin Kit
40-119
Tools and Sales Support Items
Plug Holder
40-066
Contains finger pins, springs and 40-066 plug holder�
Key Gage
40-104
4 0 - 1 0 4 K E Y G A G E
Contains all conventional pins and springs, follower, tweezers and M540-056 cylinder cap removal tool�
Key Machine
40-075
Has grooves for Primus sidebar� Included in
40-070 finger pin kit�
Upgrade Kit
40-074
®
9 8 7 6 5 4 3 2 1 0
¨
PR
O
-LO
K
9
8
7
6
5
4
3
2
1
0
9
8
7
6
5
4
3
2
1
0
PR
O
-LO
O
RA
K T
NG
O
O
E,
LS
&
92
A
86
CC
LIT
Y
ES
RIE
TOOLS
BLUE
PUNCH
# B P201
Blue punch for cutting Obverse and Everest
Open C family keys�
Replaces jaw on Blue punch key machines manufactured before 7/99 to add Everest
C family capability to Obverse family key machines�
Classic Primus XP Demo Kit Everest Primus XP Demo Kit Cutaway Cylinder
40-146-XP 40-077-XP 40-072-XP
40-073-XP
1
SCHLAGE
PRIMUS
PRIMU
S
Contains an interchangeable core cylinder, and sample conventional and Primus cylinders� A finger pin and sidebar are encased in lucite on a key chain� A cutaway
Primus cylinder is also included�
ID cards
Level 1 ID Card
Level 1+ ID Card
Level 2 ID Card
Everest Primus ID
Level 1 XP ID Card
Level 1+ XP ID Card
Level 2 XP ID Card
Everest XP Primus ID
*Specify Level 7 or 8
40-061
40-065
40-062
40-070*
40-061-XP
40-065-XP
40-062-XP
40-070-XP*
Contains the sales tools to sell Everest and
Everest Primus� Cylinder formats include: key-in-knob/key-in-lever, full-size IC, SFIC and mortise� Includes Everest Open and Everest
Primus cutaway cylinders and an Everest
Primus ID card and key chain�
Forms
Key Order Form
Primus Control Register
Signature Card
Face Sheet
MS-E110
MS-E160
MS-E130
MS-E120
40-072 Classic Primus
Included in 40-146 demo kit�
40-073 Everest Conventional
Included in 40-077 demo kit�
Other Cylinder tools
Cap Removal Tool
Shell Loading Tool
M540-056
40-116
39
Primus Service Manual
Interpreting Box Labels
Interpreting Box Labels
Cylinder Length (Mortise ONLY) 1/8" shown
Cylinder Part Number Keyway
Key Part Number
Keying Details
Schlage Use Only
Accessories
(e�g� special cams)
Product: 20-700 118 C123
Keytype: 48-004 Qty: 2
Keyset: AA1 Door: 123
Set: AA
Sequence: 2
Primus Seq: 1234
Acc. XB11-946
Level: 9Z
Order: 888888-001
Keyway
Door Number
Primus Sequence
(Unique for each set of keyways and side bitting)
Level Number
Schlage Order Number
Primus Service Manual
40
Three Parts to Key Control
Three Parts to Key Control
How do you account for the keys you have issued? How do you know for sure who has keys to various areas of your building or campus? Facilities who have proper key control procedures in place know the answers these questions�
To help guide Facilities Directors, Security Directors, etc� in knowing who has access to the mechanical locks in their facility, Schlage offers a three-part solution�
1� Key Issue Policies
Without a sensible key control policy backed by top management, security can deteriorate quickly� The policy should define what level of authority is required to authorize keys to be cut�
Issuing master and grand master keys must be done based solely on actual need, not desire or ego� After all, it does little good to prevent keys from being duplicated externally if you issue many “legitimate” copies of the top master key which can get lost or stolen�
•
•
Here are some ideas which you may modify and adopt if they seem appropriate for your particular facility:
• Establish a suitable management level (department head, shop foreman, etc�) to authorize keys to be cut or issued to employees� This should be a sliding scale requiring higher level approval for master and grand master keys�
Collect a deposit for all keys issued�
Require the employee to sign a receipt stating that his/her final pay check will be withheld until all keys are returned� This requires coordination with the
Human Resources or Accounting Department�
•
•
•
Have the key holder or the department sign a receipt making them responsible for the cost of rekeying any areas operated by the lost or stolen key�
Serial number all keys to differentiate and track multiple copies of the same key issued to different persons� This allows your key control center to trace any key to the rightful key holder�
Include language on a key receipt that forbids
•
•
•
• lending of keys to other employees�
Dedicate resources for periodic spot checks to make sure employees’ have their issued keys�
Do not store quantities of unused master keys�
Destroy them or provide secure storage if necessary�
Trades, contractors, and maintenance personnel should turn in their rings of master keys at the end of their shifts and pick them up again the next day�
Implement true enforcement with consequences or policies will soon be ignored�
2� Track Issued Keys with SiteMaster 200
Implementing a system to track each and every key issued is critical� This allows immediate answers to the questions of who has access to any given area at any given time� Schlage SiteMaster 200 software is great for this�
SiteMaster 200 has fields for key holder name, key symbol (code), serial number of key, door name, number, etc� Once the data has been entered you can sort it in a variety of ways to produce reports or simply look up an individual person, key, door, etc�
To be effective, one primary person should be designated responsible for maintaining this database, with backup personnel designated as necessary� Too many people with access to the database can lead to a breakdown in the integrity of the information�
3� Use Patented Keys
Be sure Parts 1 and 2 are in place�
Install Primus or Everest Primus patented keyways�
You can now be reasonably sure that your keys won’t be copied� It would be difficult, time consuming, and a violation of federal patent law to make an unauthorized copy of a Primus or Everest Primus key� A person who makes an unauthorized Primus or Everest Primus key could be subjected to legal action from Schlage�
41
Primus Service Manual
Ordering Primus
Ordering Primus
Cylinders
Everest Primus/Everest Primus XP and Classic Primus/
Primus XP complete cylinders have the same pricing and part numbers� As with Classic Primus Levels 3 and
4, face sheets are required for Level 9 orders�
To order:
1� Select the Primus cylinder from the cylinder Price
2�
Book pages�
If a specific keyway is desired, specify the Classic or
3�
Everest keyway�
Specify keying, finish, cylinder length, or any other fields as necessary�
Example:
How to order a zero-bitted Everest Primus XP non-
UL cylinder with a 626 finish and C123 keyway for a
D-Series Lever lock:
Step 1: The Primus cylinder part number is 20-750-XP
Step 2: The keyway desired is C123
Step 3: The keying is zero bitted (000000) and the finish desired is 626�
Order: 20-750 626-XP C123-000000
Cylinder Bulk Packs
All Primus and Primus XP products are available in a
Bulk Pack� No signatures or authorizations are required when ordering Bulk Pack Cylinders�
To Order:
1� Choose your Bulk Pack from the Price Book pages based on the cylinder format, finish, and keyway�
Check the Express Stock listing for faster delivery�
2� For key-in-knob/lever or mortise cylinders, choose the required tailpieces or cams and collars from the existing Everest Bulk Pack tailpiece, cam and collar offering (Everest, Classic Primus, and Everest
3�
4�
Primus all use the same tailpieces)�
If needed, order a 40-070 Primus pin kit or Primus components�
Order keys as needed� For fastest delivery, order keys separately and write “QuicKey” on your order�
NOTE: Orders for Level 9 keys must be accompanied by a face sheet�
Primus Service Manual
42
Limited Warranty
Limited Warranty
PATENT NOTICE
Schlage® products and those of its subsidiary companies and licensees may be covered by both issued and pending U�S� and foreign patents, copyrights and trademarks� Manufactured items are covered by one or more of the following patents:
4884835
5070715
5152558
5308131
5533368
5566996
5604970
5628216
5657653
5683127
5697653
5715717
5718468
5722276
5769472
5782118
5809816
5881590
5947537
6038896
6042417
6131966
6189351
6516644
6553800
6568725
6612141
6615629
6619705
6869116
6905773
6988751
7036856
7051562
7063363
7248836
D372417
D372854
D397993
D400348
D411732
D426452
D428324
D493089
LIMITED WARRANTY: COMMERCIAL APPLICATIONS
3-Year Limited Warranty
Schlage Lock Company (the “Company”) extends a three-year limited warranty from the original date of purchase to the Original User of the products manufactured by the Company (the “Product”) against defects in material and workmanship� Certain Products contain restrictions to this limited warranty, additional warranties or different warranty periods� Please see below for specific Product warranty information�
The provisions of this warranty do not apply to Products: (i) used for purposes for which they are not designed or intended; (ii) which have been subjected to alteration, abuse, misuse, negligence or accident; (iii) which have been improperly stored, installed, maintained or operated; (iv) which have been used in violation of written instructions provided by Schlage; (v) which have been subjected to improper temperature, humidity or other environmentalconditions (i�e�, corrosion); or (vi) which, based on Schlage’s examination, do not disclose to Schlage’s satisfaction non-conformance to the warranty� Additionally, Schlage will not warrant ANSI A156�2
Grade 2 lever Product installed in educational facilities and student housing�
SPECIFIC PRODUCT WARRANTY RESTRICTIONS / ADDITIONAL WARRANTIES
Portable Security Products Warranty: A limited lifetime warranty is provided to the Original User, subject to the restrictions of this limited warranty, except that the
Company’s sole obligation under this warranty is to replace the Product�
ND-Series Levers 7-Year Mechanical Warranty: A limited warranty is provided to the Original User for seven (7) years from original date of purchase, subject to the restrictions of this limited warranty�
Small Format Interchangeable Core (SFIC) Warranty: This limited warranty also applies to Schlage locks and housings when used with another manufacturer’s cores, or to Schlage cores (i�e� SFIC) when used in another manufacturer’s locks and housings� The use of unauthorized cylinder cams or other components with the Products shall void this warranty�
Everest® Primus® Limited Lifetime Key Breakage Warranty: A limited lifetime warranty is provided to the Original User against key breakage, subject to the restrictions of this limited warranty�
Cobra, CM and PRO-Series 1-Year Electronic Lock Warranty: A limited warranty is provided to the Original User for one (1) year from original date of purchase, subject to the restrictions of this limited warranty�
Limited Lifetime Mechanical and Finish Warranty
Subject to the terms and conditions of this warranty, the Company extends a limited lifetime mechanical and finish warranty to the Original User of the Product against defects in material and workmanship as long as the Original User occupies the residential premises upon which the Product was originally installed�
The provisions of this warranty do not apply to Products: (i) used in commercial applications; (ii) used in common area applications; (iii) used for purposes for which they are not designed or intended; (iv) which have been subjected to alteration, abuse, misuse, negligence or accident; (v) which have been improperly stored, installed, maintained or operated; (vi) which have been used in violation of written instructions provided by Schlage; (vii) which have been subjected to improper temperature, humidity or other environmental conditions; or (viii) which, based on Schlage’s examination, do not disclose to Schlage’s satisfaction non-conformance to the warranty�
Additionally, this warranty DOES NOT COVER scratches, abrasions, or deterioration due to the use of paints, solvents or other chemicals� Exclusions: Oil Rubbed
Bronze finish (613) is designed to improve over time and change in appearance, creating a living finish through daily use and thus, finish discoloration is not applicable to the above warranty�
ADDITIONAL TERMS & CONDITIONS APPLYING TO BOTH COMMERCIAL & RESIDENTIAL APPLICATIONS OF COMMERCIAL PRODUCTS
What the Company Will Do: Upon return of the defective Product to the Company, the Company’s sole obligation, at its option, is to either repair or replace the Product, or refund the original purchase price in exchange for the Product�
Original User: This warranty only applies to the Original User of Products� This warranty is not transferable�
What is Not Covered: The following costs, expenses and damages are not covered by the provisions of this limited warranty: (i) labor costs including, but not limited to, such costs as the removal and reinstallation of Products; (ii) shipping and freight expenses required to return Products to Schlage; and (iii) any other incidental, consequential, indirect, special and/or punitive damages, whether based on contract, warranty, tort (including, but not limited to, strict liability or negligence), patent infringement, or otherwise, even if advised of the possibility of such damages� Some local laws do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to you�
How Local Law Applies: This warranty gives you specific legal rights, and you may also have other rights as otherwise permitted by law� If this Product is considered a consumer product, please be advised that some local laws do not allow limitations on incidental or consequential damages or how long an implied warranty lasts, so that the above limitations may not fully apply� Refer to your local laws for your specific rights under this warranty�
Warranty Claims: If you have a claim under this warranty, please contact Schlage Customer Service (800-847-1864) for repair, replacement or refund of the original purchase price in exchange for the return of the Product to Schlage�
Miscellaneous: The Company does not authorize any person to create for it any obligation or liability in connection with the Product� The Company’s maximum liability hereunder is limited to the original purchase price of the Product� No action arising out of any claimed breach of this warranty by the Company may be brought by the
Original User more than one (1) year after the cause of action has arisen�
43
Primus Service Manual
Download
Advertisement
Key features
High Security
Different Key Control Levels
Geographical Exclusivity
UL437 Drill Resistance
Key Duplication Restrictions
Master Keying Options
Limited Key Duplication
Time Zone Exclusivity
Nationwide Exclusivity
Lockout Function
Frequently asked questions
The Primus key system has different Key Control levels that offer varying levels of key duplication restrictions and geographical exclusivity. These levels are designed to meet the specific security needs of different businesses and organizations. Level 1 is the most basic level and is available to any locksmith. Level 1+ is only available to dealers who have signed a contract with Schlage and purchased the required minimum dollar amount of inventory. Level 2 cylinders are assigned a time zone exclusive pair of side bittings. Level 3 and 4 cylinders offer the highest level of key control and exclusivity on Classic keyways. Everest Primus Level 7, 8 and 9 cylinders are designed for large key systems and offer the highest level of security.
Primus XP cylinders have a #7 side pin added to provide more combinating options as well as added security.
The Primus/Primus XP lockout cylinder is for use in applications in which it is necessary to temporarily disable the cylinder. It is essentially a very basic access control device. It utilizes a standard 6-pin chamber row as well as a 4-pin chamber row with a special key. The operating key cannot be removed in the lockout position because the back two pins are unable to disengage from the key. When the plug is in its standard operating position all keys will operate the lock. To temporarily disable to regular operating keys, the plug can be turned with the special key to align the bottom pins with the lockout row of pins.
The appropriate level of key control depends on the specific security needs of your business or organization. If you require a high level of security and exclusivity, you should consider using a higher level of key control, such as Level 3 or 4. If you need a more basic level of security, Level 1 or 1+ may be sufficient.