Cisco Nexus 1000V Switch for Microsoft Hyper-V Installation Guide
Below you will find brief information for Nexus 1000V for Microsoft Hyper-V. The Cisco Nexus 1000V is a virtual networking solution designed for Microsoft Hyper-V virtualization platforms. It extends Cisco networking features and policies to the virtualized environment, providing consistent network management, security, and monitoring across both physical and virtual infrastructures.
Advertisement
Advertisement
Cisco Nexus 1000V for Microsoft Hyper-V
Installation Guide
Release 5.2(1)SM1(5.1)
May 30, 2013
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA http://www.cisco.com
800 553-NETS (6387)
Text Part Number: OL-28335-01
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL
STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT
SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE
OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH
ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT
LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF
DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,
WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO
OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this
URL: www.cisco.com/go/trademarks . Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
© 2013 Cisco Systems, Inc. All rights reserved.
OL-28335-01
C O N T E N T S
Preface
v
v
v
vi
vi
vii
Obtaining Documentation and Submitting a Service Request
viii
Installing the Cisco Nexus 1000V for Microsoft Hyper-V
1-1
1-2
1-2
1-2
1-2
1-3
1-4
1-5
1-6
Downloading Cisco Nexus 1000V Package
1-6
1-6
Installing the Software using Installer App
1-6
Installing Cisco Nexus 1000V for Microsoft Hyper-V Manually
1-11
Preparing Microsoft Hyper-V Hosts
1-19
MTU configuration with Cisco Nexus 1000V:
1-19
VMQ Processor Configuration with Cisco Nexus 1000V
1-19
1-20
Adding Hosts to Logical Switch
1-20
Connecting VMs to Logical Switch
1-21
Connecting VM Network Adapter to Logical Switch
1-21
Installing a VSM on Cisco Cloud Services Platform
2-23
Installing VSM on Cisco Cloud Services Platform
2-23
2-23
2-23
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide, Release 5.2(1)SM1(5.1) iii
Contents iv
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide, Release 5.2(1)SM1(5.1)
OL-28335-01
Preface
This preface describes the audience, organization, and conventions of the Cisco Nexus 1000V for
Microsoft Hyper-V Installation Guide, Release 5.2(1)SM1(5.1). It also provides information on how to obtain related documentation.
This preface includes the following sections:
•
•
•
•
•
•
Related Documentation, page vi
Documentation Feedback, page vii
Obtaining Documentation and Submitting a Service Request, page viii
Audience
This guide is for network administrators and server administrators with the following experience and knowledge:
•
•
•
An understanding of virtualization
Ability to set up and configure Microsoft Windows Virtual Machine Manager
Using Microsoft Windows Virtual Machine Manager (SCVMM) software to create a virtual machine and configure a virtual switch
Document Conventions
Command descriptions use these conventions: boldface font italic font
{ }
[ ]
Commands and keywords are in boldface.
Arguments for which you supply values are in italics.
Elements in braces are required choices.
Elements in square brackets are optional.
OL-28335-01
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide, Release 5.2(1)SM1(5.1) v
Chapter
S e n d d o c u m e n t c o m m e n t s t o n e x u s 1 k - d o c f e e d b a c k @ c i s c o . c o m .
x | y | z string
Alternative, mutually exclusive elements are separated by vertical bars.
A nonquoted set of characters. Do not use quotation marks around the string or the string will include the quotation marks.
Screen examples use these conventions: screen font boldface screen font
Terminal sessions and information the device displays are in screen font.
Information you must enter is in boldface screen font.
italic screen font
< >
[ ]
!, #
Arguments for which you supply values are in italic screen font.
Nonprinting characters, such as passwords, are in angle brackets.
Default responses to system prompts are in square brackets.
An exclamation point (!) or a pound sign (#) at the beginning of a line of code indicates a comment line.
This document uses the following conventions for notes and cautions:
Note Means reader take note . Notes contain helpful suggestions or references to material not covered in the manual.
Caution Means reader be careful . In this situation, you might do something that could result in equipment damage or loss of data.
Available Documents
You can view and download documentation for the current version of Cisco Nexus 1000V for Microsoft
Hyper-V at the location: http://www.cisco.com/en/US/products/ps13056/tsd_products_support_series_home.html
Related Documentation
This section lists the documents used with the Cisco Nexus 1000V for Microsoft Hyper-V.
General Information
Cisco Nexus 1000V for Microsoft Hyper-V Release Notes
Install and Upgrade
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
Configuration Guides
Cisco Nexus 1000V for Microsoft Hyper-V High Availability and Redundancy Configuration Guide
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide, Release 5.2(1)SM1(5.1) vi OL-28335-01
Chapter
Cisco Nexus 1000V for Microsoft Hyper-V Interface Configuration Guide
Cisco Nexus 1000V for Microsoft Hyper-V Layer 2 Switching Configuration Guide
Cisco Nexus 1000V for Microsoft Hyper-V License Configuration Guide
Cisco Nexus 1000V for Microsoft Hyper-V Network Segmentation Manager Configuration Guide
Cisco Nexus 1000V for Microsoft Hyper-V Port Profile Configuration Guide
Cisco Nexus 1000V for Microsoft Hyper-V Quality of Service Configuration Guide
Cisco Nexus 1000V for Microsoft Hyper-V Security Configuration Guide
Cisco Nexus 1000V for Microsoft Hyper-V System Management Configuration Guide
Programming Guide
Cisco Nexus 1000V for Microsoft Hyper-V REST API Guide
Reference and Troubleshooting Guides
Cisco Nexus 1000V for Microsoft Hyper-V Command Reference
Cisco Nexus 1000V for Microsoft Hyper-V Troubleshooting Guide
Virtual Services Appliance Documentation
The Cisco Nexus Virtual Services Appliance (VSA) documentation is available at http://www.cisco.com/en/US/products/ps9902/tsd_products_support_series_home.html
Virtual Security Gateway Documentation
The Cisco Virtual Security Gateway documentation is available at http://www.cisco.com/en/US/products/ps11208/tsd_products_support_model_home.html
Virtual Network Management Center
The Cisco Virtual Network Management Center documentation is available at http://www.cisco.com/en/US/products/ps11213/tsd_products_support_series_home.html
Virtual Wide Area Application Services (vWAAS)
The Virtual Wide Area Application Services documentation is available at http://www.cisco.com/en/US/products/ps6870/tsd_products_support_series_home.html
ASA 1000V Cloud Firewall
The ASA 1000V Cloud Firewall documentation is available at http://www.cisco.com/en/US/products/ps12233/tsd_products_support_series_home.html
Documentation Feedback
To provide technical feedback on this document, or to report an error or omission, please send your comments to [email protected]. We appreciate your feedback.
OL-28335-01
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide, Release 5.2(1)SM1(5.1) vii
Chapter
S e n d d o c u m e n t c o m m e n t s t o n e x u s 1 k - d o c f e e d b a c k @ c i s c o . c o m .
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation , which also lists all new and revised Cisco technical documentation: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What’s New in Cisco Product Documentation as an RSS feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service. Cisco currently supports RSS Version 2.0.
viii
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide, Release 5.2(1)SM1(5.1)
OL-28335-01
C H A P T E R
1
Installing the Cisco Nexus 1000V for Microsoft
Hyper-V
This chapter includes the following sections:
•
•
•
•
•
•
Installation Workflow, page 1-5
OL-28335-01
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
1-1
Chapter 1 Installing the Cisco Nexus 1000V for Microsoft Hyper-V
Prerequisites
Prerequisites
Make sure that you have the following components installed and configured on the target setup:
• Windows Active Directory service
•
•
Microsoft System Center Virtual Machine Manager (SCVMM) 2012 SP1 UR2 build version
3.1.6020.0
Windows Server 2012 Hosts
System Requirements
This section describes the hardware and software requirements.
Hardware Requirements
The hardware must meet the requirements set by Microsoft to run the Hyper-V role. Cisco Nexus 1000V for Microsoft Hyper-V Virtual Supervisor Module (VSM) requires VMs with the following configuration:
• 4 GB minimum of hard disk space
•
•
4 GB minimum of RAM
Four network adapters (network interface cards—NICs) on the host where Microsoft Hyper-V is installed. You can have various combinations depending on the hardware you have. For example, you can have one NIC with four ports or four NICs with one port each.
Software Requirements
To install and bring up a Cisco Nexus 1000V for Microsoft Hyper-V, you need the following server setup:
• Microsoft System Center Virtual Machine Manager (SCVMM) 2012 SP1 UR2 build version
3.1.6020.0
•
•
•
Windows 2012 hosts
Active Directory server
To configure the VSM, you need the following information:
• VSM IP address
• VSM domain ID (1-1023)—This is used for High Availability (HA)
Layer 3 connectivity between a VSM and the hosts running a VEM is required.
•
– L2 control is not supported.
TCP Port 80 open on the network for communication from System Center Virtual Machine Manager to VSM
1-2
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
OL-28335-01
Chapter 1 Installing the Cisco Nexus 1000V for Microsoft Hyper-V
VSM NIC Ordering
VSM NIC Ordering
The VSM creates interfaces in an ascending MAC order of the virtual NIC offered by Microsoft Hyper-V.
Currently, Microsoft Hyper V provides no guarantees that this order is the same as displayed at the VSM
VM Settings panel, but this is usually the case. VSM always uses its first interface as control0 and its second interface as mgmt0. The network profiles for these two interfaces may need to use different
VLAN. Therefore, the users should verify that the interfaces are selected by the VSM in the same order as displayed in the Settings panel, to select profiles appropriately.
If the order is not the same, the users can use the following commands to specify their preferred MAC to control0 / mgmt0 interface mappings:
• system internal control-mac XXXX.XXXX.XXXX
• system internal mgmt-mac XXXX.XXXX.XXXX
These commands require copy running-config startup-config command to be run afterwards to make the change persistent and effective after the next VSM reload.
# show system internal interface mac-address
Sample output:
Interface Preferred MAC
--------- -------------mgmt0 cccc.bbbb.aaaa
control0 aaaa.bbbb.cccc
Note Actual MAC values for currently selected control0/mgmt0 interfaces can be displayed with existing command “show interface mac-address”. After a VSM reload, both mappings should be the same, unless the system malfunctions.
If any of the preferred MAC for control0/mgmt0 selected by users is not available at VSM boot up, the driver ignores it and it picks another interface instead (following MAC ascending order). In that case, the system logs an error with a syslog as follows:
%KERN-3-SYSTEM_MSG: Preferred MAC (aaaa.bbbb.cccc) for control0 not found – kernel
OL-28335-01
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
1-3
Chapter 1 Installing the Cisco Nexus 1000V for Microsoft Hyper-V
Basic Topology
Basic Topology
displays the basic Hyper-V topology on a Cisco Nexus 1000V for Microsoft Hyper-V VEM.
Figure 1-1 Basic Topology for the Cisco Nexus 1000V for Microsoft Hyper-V
Management VM Cluster
AD
Server
Infra VM Host
SQL
VM
SCVMM
VM
Secondary VSM Host
Primary VSM Host
Nexus 1000V VSM
NIC NIC NIC
HYPER-V
Native Switch
NIC NIC NIC NIC
HYPER-V
Native Switch
NIC
Data VM Cluster
VM1 ...
VMN
... Host 64
Host 1
NIC NIC NIC
Nexus 1000V Switch
Team
NIC NIC
...
NIC
Note: The Management NIC is actually on the Microsoft Switch.
Management VM cluster for Infra VMs
Data VM Cluster for Workload VMs
Minimum topology 3 servers with 4 NICs each.
Installer APP is recommended for this topology.
displays the Cisco Nexus 1000V for Microsoft Hyper-V deployment on two servers with the following network configuration:
•
•
Management NIC–This network adapter is connected to an external network for the host OS connectivity.
Microsoft Virtual Switch–The Microsoft virtual switch with one physical network adapter for the
VSM connectivity.
• Two Physical Network adapters–These adapters are connected to the Cisco Nexus 1000V Logical
Switch instance of the Hyper-V host.
1-4
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
OL-28335-01
Chapter 1 Installing the Cisco Nexus 1000V for Microsoft Hyper-V
Installation Workflow
Installation Workflow
Figure 1-2 displays the Cisco Nexus 1000V for Microsoft Hyper-V installation process on Microsoft
System Center Virtual Machine Manager (SCVMM) 2012 SP1 UR2 build version 3.1.6020.0.
Figure 1-2
1. Download Cisco
Nexus 1000V Package
2. Install SCVMM Components
Cisco Nexus 1000V for Microsoft Hyper-V Installation Workflow
2.1 Install Cisco Provider MSI
2.2 Install Cisco Template Files
2.3 Copy VEM to SCVMM Repository
2.4 Copy VSM ISO to SCVMM Library
3. Install and Configure VSM
4. Configure SCVMM Fabric and
VM Network
5. Prepare Hyper-V Hosts
6. Create Nexus 1000V
Logical Switch Instance on hosts
7. Connect VMs to
Cisco Nexus 1000V
3.1 Create Mocrosoft Switch for
VSM Connectivity
3.2 Install VSM VM using VM Template
3.3 Configure VSM
4.1 Add Switch Extension Manager
(Connect to VSM)
4.2 Create Logical Switch
4.3 Create VM Networks
5.1 Configure PNIC MTU Settings
5.1 Configure VMQ RSS Settings
Management PNIC Workflow
6.1.1 Select Host
6.1.2 Select the MGMT PNIC
6.1.3 Create MGMT Host Virtual
Network Adapter
6.1.4 Deploy Logical Switch
6.1.5 Add Remaining PNICs to
Logical Switch
7.1 Select VM Network Adapter
7.2 Connect VM Network Adapter to Logical Switch
7.3 Select VM Network and Port
Classification for the Network Adapter
Non-MGMT PNIC Workflow
6.2.1 Select Host
6.2.2 Select the PNICs except MGMT PNIC
6.2.3 Deploy Logical Switch
6.2.4 Add any Remaining PNICs to Logical Switch
OL-28335-01
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
1-5
Chapter 1 Installing the Cisco Nexus 1000V for Microsoft Hyper-V
Installation Steps
Note Steps 2 to 4 in the installation workflow are performed by Installer App that is described in the earlier chapter. Steps 5 to 7 are common to Installer App and Manual installation methods.
Installation Steps
Refer to the installation workflow for step-by-step installation instructions.
1.
Downloading Cisco Nexus 1000V Package, page 1-6
2.
3.
4.
SCVMM and VSM Configuration, page 1-6
Preparing Microsoft Hyper-V Hosts, page 1-19
Adding Hosts to Logical Switch, page 1-20
5.
Connecting VMs to Logical Switch, page 1-21
Downloading Cisco Nexus 1000V Package
The Cisco Nexus 1000V for Microsoft Hyper-V package (a zip file) is available at the download URL location provided with the software. Complete the following steps to download the Cisco Nexus 1000V for Microsoft Hyper-V package.
1.
Download the Cisco Nexus 1000V for Microsoft Hyper-V package for Microsoft System Center
Virtual Machine Manager (SCVMM) 2012 SP1. The package contains the following files: a.
Virtual Supervisor Module (VSM) ISO (n1000vh-dk9.5.2.1.SM1.5.1.iso) b.
Virtual Ethernet Module (VEM) MSI package (Nexus1000V-VEM-5.2.1.SM1.5.1.msi) c.
Cisco VSEM Provider MSI package (Nexus1000V-VSEMProvider-5.2.1.SM1.5.1.msi) d.
Cisco SCVMM VM Template (Cisco Nexus1000V VSM Template) e.
Cisco Installer App (Cisco.Nexus1000VInstaller.UI.exe)
SCVMM and VSM Configuration
This section describes the procedure for installing the Cisco Nexus 1000V for Microsoft Hyper-V VSM software using the Installer App or using the manual installation. The recommended method of software installation is using the Installer App.
You can install the Cisco Nexus 1000V for Microsoft Hyper-V VSM software using the Installer App or using the manual installation procedure as described in the following sections:
•
Installing the Software using Installer App, page 1-6
•
OR
Installing Cisco Nexus 1000V for Microsoft Hyper-V Manually, page 1-11
Installing the Software using Installer App
Using the Installer App is the recommended method of software installation. Refer to the following sections for more information:
1-6
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
OL-28335-01
Chapter 1 Installing the Cisco Nexus 1000V for Microsoft Hyper-V
Installation Steps
•
•
Prerequisites for Using Installer App, page 1-7
Configuring SCVMM and VSM using Installer App, page 1-8
Prerequisites for Using Installer App
The Cisco Nexus 1000V Installer App is the graphical user interface (GUI) for installing the VSMs in high availability (HA) mode on Hyper-V hosts. Complete the pre-requisites listed in this section to install the Cisco Nexus 1000V for Microsoft Hyper-V VSM software using the Installer App.
The VSM is deployed with the following credentials:
•
• username: admin password: admin
Note Make sure that you have .NET 4.0 or later installed on the host.
Note Make sure that you have updated to SCVMM UR2 via Windows update. After upgrading, the new version number for SCVMM should be SCVMM UR2 build version 3.1.6020.0.
Note Make sure that the Management Physical Adapter for your Hyper-V host is free. The Installer App expects that the Management Physical Adapter used in the Host OS connectivity should not be associated with any virtual Switch and it should not be a member of a NIC TEAMING.
The machine where the installer is running should meet the following requirements:
•
•
It should be on the same domain as the SCVMM server.
It should have Microsoft SCVMM Console installed (check C:/Program Files/Microsoft/System
Center/Virtual Machine Manager to see if it is installed).
•
•
The currently logged in user should have the administrative privileges on the SCVMM server and the Library server.
The currently logged in user should be able to run PowerShell cmdlets.
Make sure you have the following information:
• SCVMM IP Address/ Host name and Port number
•
•
•
•
•
•
•
•
•
SCVMM Username and Password
ISO image location for VSM
MSI file location for VEM and MSI file for Cisco Provider DLL
VSM Management IP Address
Subnet Mask
Gateway
Domain ID
Management VLAN ID of the VSM
Management VLAN ID of the Hyper-V Hosts
OL-28335-01
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
1-7
Chapter 1 Installing the Cisco Nexus 1000V for Microsoft Hyper-V
Installation Steps
Note If you are using the SCVMM credentials that do not have the administrative rights on the SCVMM server machine, make sure that the UAC (User Account Control) on the SCVMM machine is turned off.
Complete the following procedure to install the Cisco Nexus 1000V for Microsoft Hyper-V:
1.
2.
3.
Download the Cisco Nexus 1000V package for Windows Server 2012 zip file from Cisco.com.
Unzip and launch the Cisco Nexus 1000V Installer application file.
The Cisco Nexus 1000V Installer for Microsoft Hyper-V window displays. The Cisco Nexus
1000V Installer App for Microsoft System Center 2012 with Hyper-V is available in the Install
Cisco Nexus 1000V Logical Switch (VSM Installation):
Refer to
Configuring SCVMM and VSM using Installer App, page 1-8
for installing Cisco
Nexus 1000V Logical Switch (VSM Installation).
Configuring SCVMM and VSM using Installer App
Complete the following steps to install the software to configure SCVMM and VSM using the Cisco
Nexus 1000V Logical Switch (VSM Installation) in the Installer App:
1.
Click Cisco Nexus 1000V Logical Switch (VSM Installation) and click Next .
The following prerequisites for the installation are displayed on the Prerequisites window:
–
–
Hyper-V hosts should be added to SCVMM.
Hyper-V hosts should be part of Active Directory.
– The machine where the installer is running should meet the following requirements:
• It should be on the same domain as the SCVMM server.
•
•
It should have SCVMM Console installed (Check C:/Program Files/Microsoft/System
Center/Virtual Machine Manager to see if it is installed.)
The currently logged in user should have administrative privileges on the SCVMM server and Library server.
• The currently logged in user should be able to run PowerShell cmdlets.
Once these prerequisites have been fulfilled, click Next . The Login to SCVMM window is displayed.
2.
3.
4.
In the Login to SCVMM window, enter the following SCVMM server credentials:
– Host Name or IP Address
–
–
Port (https only). The field is pre-populated with default value 8100, which can be modified if required.
User Name
– Password.
Click Next .
The Enter VSM Details window displays.
Click Import Configuration to import a saved configuration.
If you are deploying an additional VSM, the Deploy in HA mode option is provided. Check the
Deploy in HA mode option to deploy the VSM in HA mode.
1-8
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
OL-28335-01
Chapter 1 Installing the Cisco Nexus 1000V for Microsoft Hyper-V
Installation Steps
OL-28335-01
Note When the Deploy in HA mode option is selected, the Host 2 fields become active. When deploying in HA mode, both hosts should have the same configuration.
7.
8.
9.
5.
6.
For Host 1, select a host from the drop-down menu in the IP Address/Name field. If a host or a network adapter that you want to connect to is not available, see the tooltip on the Installer App window. The installer creates a Hyper-V extensible switch on the host and deploys the VSM to this switch. The selected adapter is used as an uplink for the newly created Microsoft virtual switch.
If you are deploying the VSM in HA mode, choose a host and a network adapter for the second VSM in the IP Address/Name field and in the Network Adapter field respectively. You can select the same server as Host 1 and Host 2 or select a different server for both the hosts. You can also deploy the two VSMs on the same server. In this example, a stand-alone VSM is configured.
Enter a name for the VSM in the VSM Name field.
In the ISO Image Location field, browse to the location of the VSM setup ISO file and click Open .
Browse the location of VEM MSI file and click Open .
Note Make sure that the correct MSI file with the name
Nexus1000V-VSEMProvider-5.2.1.SM1.5.1.0.msi
is selected.
10.
Enter the configuration data in the following fields:
–
–
VSM IP Address in the VSM IP Address field.
Subnet Mask VSM in the Subnet Mask field.
–
–
Gateway IP Address in the Gateway IP Address field.
Domain ID in the Domain ID field. (Make sure that this number is unique and has not been used before in the VLAN.)
11.
– VSM Management VLAN in the VSM Management VLAN field. It is the VLAN that the VSM
VM is a part of.
The following question is displayed: Is the Management VLAN of the host(s) the same as the
VSM VLAN?
The options are Yes , No .
The option that is most commonly used is Yes . If you select the option Yes , the field The management VLAN of the host(s) is : field is disabled. If you select the option No , the field The management VLAN of the host(s) is : is enabled. Enter the Management VLAN of the host.
Note If you do not know the management VLAN of the host, contact your network administrator.
12.
Once these fields are populated, the Save Configuration option becomes active.
Note The save configuration option allows you to create an XML configuration file for a later use. You can import and pre-populate the common values in the template for a later use.
13.
14.
Click Next .
Optional Step: Click Save Selection to save the entries. Click Import Selection to import the saved data on your system.
15.
Click Next .
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
1-9
Chapter 1 Installing the Cisco Nexus 1000V for Microsoft Hyper-V
Installation Steps
16.
In the Review Inputs window, each entry is validated and if there is an issue with any of the entries, you receive a Validation Error message. The error message describes the details of the error. Click
Next.
Note If a pop-up message is displayed that the Cisco Provider DLL is not installed on the SCVMM server, click Yes and browse to the location of the Cisco Provider Installation file (named
Nexus1000V-VSEMProvider-5.2.1.SM1.5.1.0.msi) in the installation package. Wait for a while before the Provider is installed and the review window is displayed.
17.
The installation begins and the Track Progress window displays each step of the installation process in real time. The green dot next to the step indicates the completion of that particular step.
A typical installation of the VSM takes about 6-8 minutes in standalone mode. If you are deploying the VSM in HA mode, installation takes about 10-15 minutes.
18.
19.
When the installation process completes, the Confirmation window is displayed.
Click Next .
The View Installation Summary window provides a brief summary along with a confirmation of the successful installation.
Warning Do not click Next until all the steps are completed. If you click Next, installation is half-complete.
20.
21.
Click Finish .
To change the password on the VSM and on the SCVMM, complete the following steps.
Enter the following command to change the password on the VSM: switch(config)# username admin password Sfish@123 switch(config)# copy r s
[########################################] 100%
Copy complete, now saving to disk (please wait)...
Modify the password on the SCVMM as follows:
Click Settings --> Security --> Run As Accounts --> Select and open the properties of the VSM
Run as Account and modify the password and Refresh the Cisco Nexus 1000V Extension Manager.
Sample Configuration
Installer App creates the following Logical Switches on the SCVMM:
1.
2.
MSFT Logical Switch for VSM Connectivity, for example, Microsoft_Switch_HPV-357
Nexus 1000V Logical Switch, for example, n1kv_HPV-357 where HPV-357 appended is the VSM name provided by the user during the installation.
Installer App creates a sample configuration for the network uplink as follows: switch# sh nsm network uplink uplink network: n1kv_uplink_network_1993_HPV-357
Publish-name: n1kv_uplink_network_1993_HPV-357
import port-profile: n1kv_uplink_network_policy_HPV-357
network segment pool:
n1kv_network_segment_pool_HPV-357
System Uplink-Network: TRUE
Switchport mode override: auto
Native network segment: n1kv_vmaccess_1993_HPV-357
port-profile config:
1-10
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
OL-28335-01
Chapter 1 Installing the Cisco Nexus 1000V for Microsoft Hyper-V
Installation Steps
switchport mode trunk
switchport trunk allowed vlan 415,1993
switchport trunk native vlan 1993
In this example, the HPV-357 appended is the VSM name provided by the user during the installation.
Refer to Cisco Nexus 1000V for Microsoft Hyper-V Network Segmentation Manager Guide for more configuration options.
Installing Cisco Nexus 1000V for Microsoft Hyper-V Manually
•
•
•
Refer to the following sections for installing Cisco Nexus 1000V for Microsoft Hyper-V:
Installing SCVMM Components, page 1-11
Installing and Configuring VSM Workflow, page 1-12
Configuring SCVMM Fabric Workflow, page 1-16
Installing SCVMM Components
Install the SCVMM components as described in the following steps:
1.
Install Cisco Provider MSI.
a.
Install the Nexus1000V-VSEMProvider-5.2.1.SM1.5.1.0.msi
from the Cisco Nexus1000V zip location on SCVMM Server in order to establish communication between SCVMM and Cisco
Nexus1000V VSM.
Note It restarts the SCVMM service.
2.
3.
b.
Verify that the Cisco Provider is installed properly by completing the following steps:
•
•
•
Open SCVMM console.
Navigate to Settings Pane.
Click on Configuration Providers.
c.
Verify the Cisco Systems Nexus 1000V extension is displayed.
Install Cisco VSM template files.
After downloading the Cisco Nexus 1000V for Microsoft Hyper-V package, complete the following steps to install the VSM template:
•
•
On SCVMM server, open the PowerShell console from the SCVMM console.
Run the script Register-Nexus1000VVSMTemplate.ps1 from the installation package.
• This script imports the Cisco VSM Template in SCVMM Library.
Copy VEM to SCVMM repository.
The VEM is an MSI file that needs to be placed in the following location on SCVMM server:
ALLUSERSPROFILE%\Switch Extension Drivers , for example, C:\ProgramData\Switch Extension
Drivers.
SCVMM uses the MSI file during Add host operation.
Warning Do not install the VEM on the SCVMM server. Only copy the file to the location specified.
OL-28335-01
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
1-11
Chapter 1 Installing the Cisco Nexus 1000V for Microsoft Hyper-V
Installation Steps
4.
Copy VSM ISO file, for example, N1000vh-dk9.5.2.1.SM1.5.0.339 to SCVMM library in the following location on SCVMM server: \\VMName\MSSCVMMLibrary . After copying the ISO file, make sure to refresh the SCVMM library so that SCVMM detects the copied ISO.
Installing and Configuring VSM Workflow
Complete the following steps to install and configure VSM workflow:
1.
2.
Create Microsoft switch for VSM connectivity.
Install VSM VM using VM Template. Refer to
Installing VSM using VM Template, page 1-12 for
more information.
3.
Configure VSM. Refer to
for more information.
Installing VSM using VM Template
Once Microsoft switch is created, install VSM VM using a VM template after completing the following steps:
1.
2.
From the left navigation pane in the SCVMM user interface, click VMs and Services icon and choose Create Virtual Machine from the top menu bar. The Create Virtual Machine Wizard window opens up.
In the Select Source panel, choose Use an existing virtual machine, VM template, or virtual hard disk option and click Browse . Choose the Nexus1000V_VSM_Template file listed under the
Type: VM Template header. Click OK and click Next .
3.
4.
In the Specify Virtual Machine Identity panel, enter the name of the virtual machine and click
Next .
In the Configure Hardware panel, configure the hardware settings for the virtual machine. If you are using a template, most of the settings have already been configured (For example, the hard drive is set to 4 GB and there are 3 network adapters). The only item that you have to manually configure is the ISO image. Click Virtual DVD drive below the Bus Configuration header in the center pane.
Click Existing ISO image file and click Browse . Choose the ISO image from SCVMM library, click
OK , and click Next .
5.
6.
7.
8.
In the Select Destination panel, keep the default settings of Place the virtual machine on a host;
Destination: All Hosts . Click Next .
Once the host is displayed in the Select Host panel, select it and click Next .
In the Configure Settings panel, review the settings and click Next .
In the Select Networks panel, specify the virtual switches that are used for the virtual machine. For each network adapter, select the type of the virtual switch, for example, Standard Switch or Logical
Switch . Click Next .
9.
10.
In the Add Properties panel, keep the default settings of the Automatic Actions . Click Next .
In the Confirm the Settings panel in the final Summary window, review and confirm the settings.
Click Create to begin the virtual machine creation. A progress bar is displayed in the Job Status column in the VM window.
11.
Once the virtual machine creation is complete, right-click the Name of the virtual machine in the
SCVMM user interface and choose Power On . Right-click the Name of the virtual machine again, click Connect or View , and choose Connect via Console .
Refer to the following table for more information on the Cisco Nexus 1000V ISO boot options.
1-12
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
OL-28335-01
Chapter 1 Installing the Cisco Nexus 1000V for Microsoft Hyper-V
Installation Steps
OL-28335-01
Table 1-1 Cisco Nexus 1000V ISO Boot Options
No. Boot Option
1 Install Cisco Nexus
1000V and bring up the new image
2
3
If the disk is unformatted
• Boot the kickstart image from
ISO
•
•
Format the disk and copy the images from ISO to bootflash:
Load the system image
Install Cisco Nexus
1000V and go to VSH shell
•
•
Boot the kickstart image from
ISO
Install Cisco Nexus
1000V only if the disk is unformatted, and bring up the new image
Format the disk and copy the images from ISO to bootflash:
• Start VSH shell
Same as option #1
4 Install Cisco Nexus
1000V only if the disk is unformatted and go to VSH shell
Same as option #1
If disk is formatted
• Boot the kickstart image from
ISO
•
•
•
Copy the images from ISO to bootflash:
Load the system image
Boot the kickstart image from
ISO
•
•
•
•
•
•
•
Copy the images from ISO to bootflash:
Start VSH shell
Boot the kickstart image from
ISO
Try to load the system image from the disk with the same name as that in ISO
If the image is not found, start
VSH shell
Boot the kickstart image from
ISO
Start VSH shell
Configuring VSM
After installing VSM using a VM template, connect to a VM console and configure the VSM. We recommend that the VSM should be deployed using the template provided by Cisco. Once the deployment is complete, power on the VSM. The following basic inputs are required for the VSM configuration:
1.
4.
5.
2.
3.
Switch Name
Domain ID
Management Address
Subnet Mask
Gateway Address
Note Make sure to eject the virtual ISO image from the CDROM.
Deploying VSM
Deploy the VSM as outlined in the following steps:
1.
The Virtual Machine Viewer window opens up. While it processes, it stops at the command prompt with the following message: Do you want to format it?
(y/n) . Enter Y for yes at the prompt.
2.
At the next command prompt, the following message is displayed: Perform r/w tests (takes very long time) on target disks? (y/n) . Enter Y for yes at the prompt.
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
1-13
Chapter 1 Installing the Cisco Nexus 1000V for Microsoft Hyper-V
Installation Steps
3.
4.
After the software is copied and the CD-ROM drive is mounted, you are prompted to enter the
System Administrator Account Setup.
At the Enter the password for “admin”: prompt, enter the password. At the Confirm the password for “admin”: prompt, re-enter the password.
Enter the high availability (HA) role at the next prompt Enter HA role
[standalone/primary/secondary] , for example, primary.
Note We recommend that you create a VSM high availability pair. Configure the first VM as the primary VSM and install the second VM as the secondary VSM.
5.
6.
7.
8.
If you set the HA role as secondary, the following question is displayed at the prompt: Setting HA role to secondary will cause a system reboot. Are you sure (yes/no)?: Enter Yes if you want to set the HA role to Secondary .
Enter the domain ID at the prompt: Enter the domain ID[1-1023] , for example, 199. A domain ID is required for the VSMs to communicate with each other.
After step 5 for secondary VSM, the message is displayed: saving boot configuration and the system reloads.
At the next prompt, the Basic System Configuration Dialog is displayed. Enter Yes at the prompt.
At the next command prompt, the following message is displayed: Create another login account?
[yes/no] (n) . Select No to skip creating another login account.
Note The defaults are used if you do not change the values.
9.
10.
11.
Enter the switch name, for example, Nexus1000V-Eng .
Press Y for yes when prompted to continue with the out-of-band management configuration.
Enter the Mgmt0 IPv4 address for the VSM, for example, 10.10.10.4. You can enter any IP address.
12.
13.
14.
15.
Enter the Mgmt0 IPv4 netmask, for example, 255.255.255.0.
At the next command prompt, the following message is displayed: Configure the default gateway?
Enter Y for yes.
Enter the IPv4 address of the default gateway, for example, 10.10.10.5.
At the next command prompt, the following message is displayed: Vem feature level will be set to
5.2(1)SM1(5.1). Do you want to reconfigure? (yes/no) [n]: Press Enter at the prompt to enter the default value.
16.
17.
The following message is displayed: Would you like to edit the configuration? (yes/no) [n]: Press
Enter at the prompt to enter the default value.
Complete steps 1 to 5 to configure the secondary VSM with an HA role.
18.
Verify the HA role using the command show system redundancy status on primary and secondary
VSMs.
Logging into VSM
After completing these steps, you are prompted to log into the VSM. Access the VSM via SSH using the
IP address configured in the VSM installation section. The following minimal objects need to created on the VSM:
1.
2.
Logical Network
Network Segment Pool
1-14
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
OL-28335-01
Chapter 1 Installing the Cisco Nexus 1000V for Microsoft Hyper-V
Installation Steps
3.
4.
IP Pool Template
Network Segment
Virtual Ethernet Port Profile 5.
6.
7.
2.
Ethernet Port Profile
Network Uplink
Complete the following steps to configure the VSM:
1.
Enter the configuration mode using the command config t .
1.
Create a Logical Network using the command nsm logical network <name> at the prompt to configure the SCVMM networking fabric, for example, nsm logical network Intranet . Type exit .
You can enter any name for the Logical Network.
Create a Network Segment Pool using the command nsm network segment pool <name> , for example, nsm network segment pool IntranetSJ .
3.
4.
5.
6.
Associate the Network Segment Pool to the Logical Network using the command: member-of logical-network <name> , for example, member-of logical-network Intranet . Type exit .
Create an IP pool template using the command nsm ip pool template <name> , for example, nsm ip pool template pool10 .
Configure the IP address range and network IP address range using the commands, for example, ip address < 30.0.0.2> <30.0.0.100> and network < 30.0.0.2> <255.255.255.0>.
Create a Network Segment using the command using the command, nsm network segment
<name>, for example, nsm network segment VMNetworkA .
7.
8.
9.
10.
Enter the command switchport access vlan 100 .
Associate the Network Segment Pool to the Network Segment using the command member-of network segment pool <name> , for example, member-of network segment pool IntranetSJ .
Import the IP pool template to the Network Segment using the command ip pool import template
<name> , for example, ip pool import template pool10 .
Create a VLAN inside the Network Segment using the command switchport access vlan
<number> , for example, switchport access vlan 100 .
11.
12.
Publish the Network Segment using the command publish network segment <name> , for example, publish network segment VMNetworkA . Type exit .
Create a virtual Ethernet port profile using the command port-profile type vethernet <name> , for example, port-profile type vethernet UplinkNoPortChannel .
13.
14.
Enter the no shutdown command to keep the system in a power-on state. Enter state enabled at the prompt.
Publish the port profile using the command publish port-profile and type exit . The port profile is imported for publishing the Network uplink.
15.
Create a type Ethernet policy before the creation of Network Uplink: switch(config)# port port-channel port-group-monitor port-monitor port-profile switch(config)# port-profile type ethernet eth-pp-policy switch(config-port-prof)# no shutdown switch(config-port-prof)# state enabled switch(config-port-prof)# exit
16.
Create a Network Uplink using the command nsm network uplink NexusUplink .
OL-28335-01
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
1-15
Chapter 1 Installing the Cisco Nexus 1000V for Microsoft Hyper-V
Installation Steps
17.
Associate the Network Segment Pool using the command allow network segment pool IntranetSJ , for example, allow network segment pool IntranetSJ .
18.
19.
Import the port profile that was created earlier using the command import port-profile < name >, for example, import port-profile eth-pp-policy .
Publish the Network Uplink using the command publish network uplink <name> , for example, publish network uplink NexusUplink .
20.
21.
Copy the running configuration to the start-up configuration using the copy running-config startup-config command. The following message is displayed in the window: Copy complete, now saving to disk (please wait)
Enter the show running-config command to verify the configuration.
Note The setup script configures the VSM to function in L3 control mode. L2 control mode is not supported with Cisco Nexus 1000V for Microsoft Hyper-V. When configuring L3 control with Microsoft Hyper-V, you do not need to create a port profile with capability L3control. The VSM communicates with the
Microsoft Server 2012 management interface directly. There is no need to create a special vEthernet port profile to be assigned to the Windows 2012 host.
Configuring SCVMM Fabric Workflow
Complete the following steps to configure SCVMM fabric workflow:
1.
2.
Add Switch Extension Manager (Connect SCVMM to VSM). Refer to
for more information.
Create Logical Switch. Refer to
Creating Logical Switch in SCVMM, page 1-17
for more information.
3.
Create VM Networks. Refer to
Configuring VM Network, page 1-18 for more information.
Connecting SCVMM to VSM
Once the VSM is up, configure the SCVMM networking fabric for the Nexus 1000V.
Note Check and turn off the proxy server settings for your LAN in the Internet Options settings window of
Internet Explorer before proceeding to the next steps.
Complete the following instructions to retrieve the objects from the VSM to SCVMM.
1.
When the VSM is up, log in to the VSM using SSH and the IP address configured in the previous section.
2.
3.
From the SCVMM administrator console, navigate to the Fabric pane.
On Fabric Pane under Networking , select Switch Extension Manager .
4.
5.
Right click to add a New Extension Manager . The Add Virtual Switch Extension Manager
Wizard window is displayed.
In the General panel of the Add Virtual Switch Extension Manager Wizard window, enter the connection settings for the extension manager as outlined in the following steps: a.
Select a manufacturer, for example, Cisco Systems . b.
Select the model type, for example, Nexus 1000V .
1-16
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
OL-28335-01
Chapter 1 Installing the Cisco Nexus 1000V for Microsoft Hyper-V
OL-28335-01
Installation Steps c.
Select the configuration provider for the extension manager, for example, Cisco Systems Nexus
1000V . d.
Enter the IP address of the VSM in the connection string, for example, http://10.10.10.4
.
e.
Create a run as account for the VSM. In the Run As account field, click Browse..
. The Select a Run As Account window opens up. f.
In the Select a Run As Account window, select an account from the available options or click
Create Run As account tab to create an account for the VSM. A Create Run As account window opens up. g.
In the Create Run As account window, enter the following VSM credentials:
–
–
Enter the name of the account in the Name field as VSM_admin .
Enter the description of the account in the Description field.
–
–
Enter the user name in the User Name field and the password in the Password field.
Confirm the password in the Confirm password field.
–
–
Uncheck the Validate Domain Credentials box as the Active Directory cannot be validated with the credentials.
Click OK .
– The new account, for example, VSM_admin is displayed in the Select a Run As Account window. This is a one-time procedure for the VSM. h.
Select the new account and click OK in the Select a Run As Account window.
6.
7.
Click Next .
In the Host Groups panel, select a few or all the host groups that can use the virtual switch extension manager and click Next .
8.
In the Summary panel, confirm the settings and click Finish .
Once the Virtual Switch Extension Manager has been successfully added, it is listed in the main window in the SCVMM user interface at the path: Fabric -> Switch Extension Managers .
Creating Logical Switch in SCVMM
Once the Virtual Switch Extension Manager has been added, create a logical switch on VMM. Define the extensions and port profiles for the logical switch, create classifications that contain the native port profile and a port profile for each extension as outlined in the following steps.
Complete the following steps to create the logical switch:
1.
In the SCVMM user interface, click Logical Switches under Networking in the left navigation panel. The Create Logical Switch Wizard window is displayed.
4.
5.
2.
3.
The Getting Started panel opens up. Review the instructions and click Next .
In the General panel, add a name for the logical switch in the Name field, for example,
N1000V_Test .
Click Next .
In the Extensions panel, the virtual switch extensions are listed. Choose the extensions that you want to use with the logical switch. The following extensions are displayed in the Virtual switch extensions panel:
–
–
Microsoft NDIS Capture, Extension type: Monitoring
Microsoft Windows Filter, Extension type: Filter
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
1-17
Chapter 1 Installing the Cisco Nexus 1000V for Microsoft Hyper-V
Installation Steps
6.
7.
– Configured VSM, Extension type: Forwarding
Select the Cisco extension. Only one forwarding extension can be selected.
Click OK and click Next .
In the Uplink panel, specify the uplink port profiles that are part of this logical switch. The uplink port profiles are available for use on the hosts where an instance of the logical switch is created.
– Choose Team in the Uplink mode field to select multiple uplinks.
Note Even if you use a single uplink or multiple uplinks, the mode should always be Team .
8.
–
–
In the Uplink port profiles field, click Add..
The Add Uplink Port Profile window opens up.
Select a port profile that is available for use by the host physical adapter that connects to this logical switch.
Click Next .
In the Virtual Port panel, click Add.. The Add Virtual Port window opens up.
–
–
Choose the VSM by checking the Nexus 1000v-Test check box.
Select the port profile from the drop-down menu. Select a port profile classification for the port profile, for example, AllAccess1 .
– Click Browse.. in the Port Classification field. Assign the selected port profile to a port classification in the Select a Port Profile Classification window.
– Click Create Port Classification..
. The Create Port Classification Wizard window opens up. Enter the name for the port profile classification in the Name field, for example,
AllAccess1 . Enter the description for the port profile classification in the Description field.
– Click OK . Now the selected port classification is displayed in the Select a Port Profile
Classification window.
9.
10.
– Choose the Port Profile Classification you just created and click OK .
Click OK to finish adding the Virtual Port.
Click OK and click Next to close the Create Logical Switch Wizard window.
11.
In the Summary panel, confirm the settings and click Finish . Now the logical switch is created.
The defined configuration is available on every host that uses the logical switch and the hosts, virtual switches, and virtual machines remain in compliance with their associated logical switch
Note If you want to add more port profiles to the VSM, you have configure the properties again. All the hosts should be configured for multiple uplinks. To update the properties and add more uplink port profiles, right-click the logical switch in the SCVMM user interface and click Properties .
Configuring VM Network
Once the logical switch and the hosts are configured, complete the following steps to configure the VMs and associate the network segments to the VMs.
1.
2.
Click VMs and Services in the left navigation panel of the SCVMM user interface.
Click VM Networks . Right-click and select the Create VM Network option. The Create VM
Network Wizard window opens up.
1-18
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
OL-28335-01
Chapter 1 Installing the Cisco Nexus 1000V for Microsoft Hyper-V
Installation Steps
3.
4.
In the Name panel, specify the name for the VM network in the Name field. Enter the description for the VM network in the Description field. For example, add a name for the VM network as
VM_network. If the name is same as the network-segment name, it is easy for the customers to do the mapping.
Select the logical network for the VM network in the Logical Network field.
Click Next .
5.
6.
In the Isolation panel, select Automatic to configure the isolation for the VM network automatically or select Specify an externally supplied VM network to configure the isolation externally.
Confirm the External VM Network that was previously created, for example, VM_Network.
Click Next .
7.
8.
In the Summary panel, confirm the settings and click Finish .
The new VM network is displayed in the VM Networks and IP Pools panel in the SCVMM user interface.
Preparing Microsoft Hyper-V Hosts
Prepare Microsoft Hyper-V hosts before adding hosts to the logical switch. This is an optional step.
Refer to the following sections for MTU configuration and change the RSS registry.
MTU configuration with Cisco Nexus 1000V:
In Microsoft Hyper-V, the VSM does not manage the MTU setting of VM NIC or physical adapters. All physical adapters added to the Cisco Nexus 1000V switch should have the same MTU configured and the PNIC MTU should not be changed after it is added to the switch.
Complete the following steps to configure MTU:
1.
Open View Network Connections.
2.
3.
4.
5.
Right click on the adapter and select properties.
Click Configure under the adapter properties window.
Click Advanced tab.
Click on Jumbo Packet under Property.
6.
Set the desired value of Jumbo Packet property.
Repeat these steps for all the adapters that are added to Cisco Nexus 1000V logical switch.
Certain adapters allow the MTU change only via their own adapter manager. For example, Cisco VIC cards MTU can be changed via UCSM or ILO.
VMQ Processor Configuration with Cisco Nexus 1000V
VMQ allows the network traffic received on an adapter to be spread over multiple CPU cores thereby providing better performance. For VMQ to operate correctly with Cisco Nexus 1000V, two factors are significant:
• RSS base CPU number [determines the lowest CPU core that can be used by RSS]
• Maximum number of RSS CPU [determines how many CPU cores can be used by RSS]
The above two factors should be set in such a way that same CPU core is not used by multiple NICs.
OL-28335-01
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
1-19
Chapter 1 Installing the Cisco Nexus 1000V for Microsoft Hyper-V
Installation Steps
Note Changing RSS registry is a disruptive operation and causes Ethernet Adapter to flap.
Cisco Nexus 1000V supports the following port-channel operational modes, LACP and vPC.
LACP utilizes same Subgroup id for all members of the port-channel. Therefore, Rss Base CPU and
MaxRss Processors should be set with same value for all member ports.
MAC pinning / Manual pinning port-channel use multiple subgroup id within the members of the port-channel. Therefore, Rss Base CPU and Max Rss Processors should be set in such a way that same
CPU core is not used by multiple NIC.
Steps to change RSS registry:
Complete the following steps to change RSS registry:
1.
4.
5.
2.
3.
6.
Open View Network Connections.
Right click on adapter and select properties.
Click Configure under adapter properties window.
Click Advanced tab.
Click on Maximum Number of RSS Processor under Property and Set the value.
Click on Starting RSS CPU under Property and set the value.
Repeat the steps for all the adapters that you want VMQ to be enabled.
Rss setting cannot be modified via Network connections for certain adapters. For those adapters, user needs to set the registry keys directly using the registry editor. Check Microsoft documentation for changing the registry.
Adding Hosts to Logical Switch
Once the logical switch is created, you can update the properties of the logical switch after completing the following steps.
1.
In the left navigation pane, select the server, for example, Hyper-V server under Fabric > Servers
> All Hosts , right-click, and choose Properties . The Properties window opens up.
2.
3.
Click Virtual Switches in the left navigation pane of the Properties window.
In the Virtual Switches panel, click in the New Virtual Switches field from the top menu bar and select New Logical Switch . Select the correct Logical Switch and physical adapters to assign to the
Logical Switch. The module is added to Cisco Nexus1000V VSM in a short while.
Note MGMT PNIC can be added to Logical Switch only during Switch creation time. Adding it later results in a loss of host connectivity.
4.
5.
The Nexus1000V_Test Logical Switch is displayed in this example. Under the Physical Adapter header, choose a network adapter from the drop-down list in the Adapter field. Confirm the uplink port profile for the adapter in the Uplink Port Profile field.
Click Add to add a second network adapter. Choose a different network adapter, confirm the uplink port profile and click OK .
1-20
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
OL-28335-01
Chapter 1 Installing the Cisco Nexus 1000V for Microsoft Hyper-V
Installation Steps
Note Do not use the same port profile for both adapters. If you have configured the port channels, then you can use the same port-profile on both the adapters. Refer the NSM Configuration Guide for more details.
Now, the Cisco Nexus 1000V package that was copied on the SCVMM is installed on the host.
Note We recommend that one logical switch is created per one VSM.
Connecting VMs to Logical Switch
Complete the following steps to connect VMs to the Cisco Nexus 1000VLogical Switch:
1.
Select VM network adapter.
2.
Connect the VM network adapter to Logical Switch. Refer to Connecting VM Network Adapter to
Logical Switch, page 1-21 for more information.
Connecting VM Network Adapter to Logical Switch
Once the new VM network is configured, you can deploy a VM to a VM Network as follows:
1.
Select the server on which the VM is installed in the SCVMM user interface. In the left navigation pane under VMs and Services > All Hosts , click the Hyper-V server . In the main window, right-click the virtual machine that you have created, for example, server2012_TestVM , and choose
Properties .
2.
3.
In the properties file, click Hardware Configuration in the left navigation pane.
In the Hardware Configuration panel, select NetWork Adapter . In the Network Adapter 1 panel on the right, choose Connected to a VM Network .
4.
5.
6.
7.
Select browse to find the VM network created in earlier section.
Click OK .
Connect the adapter to a combination of VM Network and Port Classification. In the Hardware
Configuration panel, under Virtual Switch, select the logical switch in the Logical Switch field, for example, Nexus1K_LS . For the classification, choose the previously created port profile in the
Classification field, for example, VethPP.
Click OK .
The Cisco Nexus 1000V for Microsoft Hyper-V installation is now complete.
OL-28335-01
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
1-21
Installation Steps
Chapter 1 Installing the Cisco Nexus 1000V for Microsoft Hyper-V
1-22
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
OL-28335-01
C H A P T E R
2
Installing a VSM on
Cisco
Cloud Services
Platform
This document includes the following sections:
•
Installing VSM on Cisco Cloud Services Platform, page 2-23
Installing VSM on Cisco Cloud Services Platform
You can install the Cisco Nexus 1000V VSM on the Cloud Services Platform.
Note Layer 3 mode is supported for Cisco Nexus 1000V for Hyper-V.
Before You Begin
Copy the ISO file to the bootflash:repository/ of the virtual service blade as displayed in the following example.
switch(config)# dir bootflash:repository
16384 Feb 21 11:31:10 2013 lost+found/
169932800 May 08 20:20:09 2013 n1000vh-dk9.5.2.1.SM1.5.0.345.iso
653 May 08 20:28:24 2013 vmpresults.txt
Usage for bootflash://sup-local
326832128 bytes used
3664547840 bytes free
3991379968 bytes total switch(config)#
Procedure
Complete the following steps to install the VSM on the Cloud Services Platform:
Step 1 Create a virtual service blade by entering the following commands. switch(config)# show virtual-service-blade summary
---------------------------------------------------------------------------------
Name HA-Role HA-Status Status Location
OL-28335-01
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
2-23
Chapter 2 Installing a VSM on Cisco Cloud Services Platform
Installing VSM on Cisco Cloud Services Platform
Step 2
Step 3
Step 4
Step 5
--------------------------------------------------------------------------------switch(config)# virtual-service-blade vsm-1 switch(config-vsb-config)# virtual-service-blade-type new n1000vh-dk9.5.2.1.SM1.5.0.345.iso
switch(config-vsb-config)# show virtual-service-blade summary
--------------------------------------------------------------------------------------
Name HA-Role HA-Status Status Location
-------------------------------------------------------------------------------------vsm-1 PRIMARY NONE VSB NOT PRESENT PRIMARY vsm-1 SECONDARY NONE VSB NOT PRESENT SECONDARY switch(config-vsb-config)#
Configure the control and packet VLANs for static and flexible topologies. Note that no provisioning is allowed for Management VLAN as the Management class interface uses the Management VLAN of the
Cloud Services Platform (CSP).
switch(config-vsb-config)# interface control vlan 391 switch(config-vsb-config)# interface packet vlan 392
Configure the Cisco Nexus 1000V on the Cisco Cloud Services Platform. switch(config-vsb-config)# enable
Enter vsb image: [n1000vh-dk9.5.2.1.SM1.5.0.345.iso]
Enter domain id[1-1023]: 391
Management IP version [V4/V6]: [V4]
Enter Management IP address: 172.16.5.5
Enter Management subnet mask: 255.255.255.0
IPv4 address of the default gateway: 172.16.5.1
Enter HostName: vsm-1
Enter the password for ‘admin’: ********
Note: VSB installation is in progress, please use show virtual-service-blade commands to check the installation status.
switch(config-vsb-config)#
Display the primary and secondary VSM status. switch(config-vsb-config)# show virtual-service-blade summary
-------------------------------------------------------------------------------
Name HA-Role HA-Status Status Location
-------------------------------------------------------------------------------
VSM-1 PRIMARY NONE VSB DEPLOY IN PROGRESS PRIMARY
VSM-1 SECONDARY NONE VSB NOT PRESENT SECONDARY switch(config-vsb-config)#
Log in to the VSM. switch(config)# virtual-service-blade vsm-1 switch(config-vsb-config)# login virtual-service-blade vsm-1
Telnet escape character is ‘^\’.
Trying 172.1.0.18...
Connected to 172.1.0.18.
Escape character is ‘^\’.
Nexus 1000v Switch vsm-1 login: admin
Password:
Cisco Nexus operating System (NX-OS) Software
TAC support: http://www/cisco.com/tac
Copyright (c) 2002-2013, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained in this software are owned by other third parties and used and distributed under license. Certain components of this software are licensed under the GNU General Public License (GPL) version 2.0 or the GNU
Lesser General Public License (LGPL) Version 2.1. A copy of each such license is available at
2-24
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
OL-28335-01
Chapter 2 Installing a VSM on Cisco Cloud Services Platform
Installing VSM on Cisco Cloud Services Platform http://www.opensource.org/licenses/gpl-2.0.php and http://www.opensource.org/licenses/lgpl-2.1.php switch# show system redundancy status
Redundancy role
---------------
administrative: primary
operational: primary
Redundancy mode
---------------
administrative: HA
operational: HA
This supervisor (sup-1)
-----------------------
Redundancy state: Active
Supervisor state: Active
Internal state: Active with HA standby
Other supervisor (sup-2)
------------------------
Redundancy state: Standby
Supervisor state: HA standby
Internal state: HA standby switch#
For more information, refer to the Logging into VSM section in the guide.
OL-28335-01
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
2-25
Installing VSM on Cisco Cloud Services Platform
Chapter 2 Installing a VSM on Cisco Cloud Services Platform
2-26
Cisco Nexus 1000V for Microsoft Hyper-V Installation Guide
OL-28335-01
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement
Key features
Seamless integration with Microsoft Hyper-V.
Advanced network management capabilities.
Enhanced security features for virtual environments.
Consistent policy enforcement.
Centralized management of virtual and physical infrastructure.
Frequently asked questions
It extends Cisco networking features to the virtualized environment.
Windows Active Directory service, SCVMM 2012 SP1 UR2, and Windows Server 2012 Hosts
TCP Port 80 needs to be open for System Center Virtual Machine Manager to VSM communication.