B. Braun Infusomat P Infusion Pump Service-Manual

Description of the voltage signals

pg. 5 - 1)

Only use original spare parts from the manufacturer. Do not tamper with assembly groups which can only be exchanged completely. The spare parts required are listed in the repair instructions.

The inspection personnel is responsible for the calibration of the test equipment. Original test equipment can be calibrated at the works of B. Braun. Further information is available upon request.

Additional notes and warnings are set off as follows:

Note

Gives additional or special notes on information and working steps.

CAUTION

Is used for working steps which may result in damage to the unit, system or to a connected device.

WARNING

IS USED FOR WORKING STEPS WHICH MAY RESULT IN PERSONAL

INJURY.

Infusomat P 2.0gb

0 - 8

Technical Training

Entry for the Product Training

Ordering of Spare Parts and Test Equipment

Return of Spare Parts

Service Hotline

Safety Officer

Translation

0 -

General Information

B. Braun Melsungen AG

Stadtwald Haus 6

D-34 212 Melsungen

Germany

Responsibility

Dieter Gundlach Tel.:

Fax:

Only via the responsible representative

+49 5661 71 - 37 74

+49 5661 71 - 28 81

B. Braun Melsungen AG

P.O. Box 11 20

D-34209 Melsungen

Germany

Hospitals and Suppliers of Hospitals

Tel.:

Fax:

+49 800 2 27 28 24

+49 5661 71 37 98

Dealer and

Medical Houses

B. Braun Melsungen AG

Schwarzenberger Weg 73-79

Wareneingang Werk C

D-34 212 Melsungen

Germany

Tel.:

Fax:

Mr. Tippel, Mr. Clobes

Tel.: +49 56 61 71 - 35 25

Fax: +49 56 61 71 - 35 26

E-Mail: [email protected]

+49 5661 71 36 28/29

+49 5661 71 35 50

Dr. Wilhelm Wucherpfennig

Fax: +49 56 61 71 - 46 36

E-Mail: [email protected]

Brückner GmbH, Germany

Infusomat P 2.0gb 0 - 7

General Information

For your notes:

0 - 8 Infusomat P 2.0gb

1 - 10

Design

Handle

Door Lock

1 -

System Overview

Guide for Short Pole Clamp

The Infusomat P is a compact volumetric peristaltic infusion pump.

Standard delivery rate range 0.1 to 999.9 ml/h

The unit is operated via a membrane keypad. It is equipped with an LCD (liquid crystal display) for the display of the delivery rate and the operating support of the user. Two control LEDs display alarms, and the running of the infusion pump.

Drop Sensor

Flow Inhibitor

MFC-Socket

Peristaltic Pump

LCD Display

Softkeys

Keypad

Barcode Label

Control LEDs

Fig.: 1 - 1 Unit Design Infusomat P

Optical

Interface fm Recessed Plug

Potential Equalization

Bolt

Drop Sensor Socket

Mains Connection

Air Sensor

IP 003

A barcode label is attached to the left front side of new Infusomat

P unit versions which can be retrofitted on previous devices. This barcode label is used to read the serial and DIANET type number via a scanner when the Infusomat P is operated in an fm-system.

Infusomat P 2.0gb 1 - 1

System Overview

Operation Flow Chart

Switch On

Tube Selection

Set Delivery Rate

Start Infusion

Standard Operation

Preselected Volume

Stop Infusion

Recall Info

Call up Bolus

KOR Mode

Service Plug,

Inserted ...

Preselected Time

Rate Calculation

Special Functions ...

Dose Calculation

Bolus Function

Standby Function

Drug Change

CC Mode

Occlusion Pressure

Drop Control

Piggyback

Battery Capacity

Data Lock

Alarm Tone

Contrast Setting

Clock

Change Delivery Rate

See service program diagram

Only when preselected time or preselected volume has expired

Please pay attention to the activation in service program

Only available with IFPC

From software IFPe, IFPE

From software IFPE

Fig.: 1 - 2

1 - 2

See Instructions for Use for detailed information.

Infusomat P 2.0gb

Function

System Overview

Two independent software-controlled microprocessor systems control and monitor the hardware. On the basis of their functions, they are defined respectively as a control and a function processor. Both systems work with independent clock frequencies and have access to different program and data memories. All safetyrelevant functions are handled by both processors and the results are counter checked (CF- and FC-latch).

The input via the keypad is fed to both processors. Additionally the acknowledgement signal of the ON/OFF key is fed to the mains power supply logic (voltage E/A-TAS). The function processor has also access to this logic via E/A-INT.

(see „Signal Table“

pg. 1 - 5)

Fig.: 1 - 3

Infusomat P 2.0gb 1 - 3

1 - 4

System Overview

Voltage Supply

The voltage supply is generated either directly from mains, via the

FM plug (14 V connection to the fluid manager system), or via the

MFC connector (11 to 16 V) and as an internal supply via the internal 7.2 V NiCD battery. The mains module is available in three versions: 230 V, 220 / 230 / 240 V and 100 / 110 / 120 V. The rated voltage has a tolerance of + 10% to – 15 %.

A voltage of 11 V to 18 V is available after transformation and rectification. This voltage is fed to the battery charge circuit and the unit supply. This is also valid for an external 12 V supply from the

MFC or FM plug. The FET V10 switches between the external and the internal voltage supply. The transistor V10b works as an ON/

OFF switch for the operating voltages UBS, UMOT and +5V. The

+5V supplies the complete electronics including the double channel microprocessor system. A window comparator constantly monitors the +5V for undervoltage or overvoltage. The function is checked during switch-on. The operating voltage UBS supplies the stepper motor and the UMOT, the stepper motor drive.

The transistor V47 switches the operating voltage UMOT. In case of an alarm the motor is switched off by V47. Additionally the switching function of the transistor is checked during the switchon test.

The circuit has two separate assembly groups with separate supply voltages UBA and UBB. The ON/OFF circuit has a retriggerable delay switch-off. A follow-up charging circuit drives the transistor V10b.

The alarm logic (operating voltage UBB) is an RS latch. This is set when the unit is running and activates the alarm circuit. The alarm buzzer and drive are also driven by UBB. The ON/OFF circuit is activated and the voltage supply is switched on by pressing the

ON/OFF key. The alarm latch is reset simultaneously. A function test of the voltage monitoring, motor circuit and alarm activation is performed. The voltage supply is maintained by cyclic self-holding pulses fed to the logic. The alarm latch is also activated.

Infusomat P 2.0gb

System Overview

Fig.: 1 - 4

Signal Table

Signal

+5V

5V-HT

5V-LT

AK-I

AK-LAD

AK-Test

ALA-UB

E/A-INT

E/A-ST

Meaning

Voltage Supply Electronic

Overvoltage Test

Undervoltage Test

Battery Charge and Discharge Current

Battery Capacity ON/OFF

Battery Test

Operating Voltage Alarm

Chip Select

Data Input

Data Output

ON/OFF by Microprocessor

ON/OFF Status

Table 1 - 1 Signal Table (Part 1 of 2)

Infusomat P 2.0gb

RDE

RES

RES-F

RES-K

RTS

Signal

PKS2

PKSS

PRS

PRS-F

PKSS

PRS.RUF

Meaning

Pump Head Sensor 2

Pump Head Sensor Control

Staff Call Relay Control

Staff Call Relay Function Channel

Pump Head Sensor Control

Staff Call Relay Control

Rate Display Enable

Power on Reset

Reset Function Channel

Reset Control Channel

Return to Send (DIANET)

Receive Data

1 - 5

1 - 6

System Overview

Signal

E/A-TAS

EDB

FMC-F

FMC-K

UEXT-N

UEXT-P

UFM-P

LFCL

LFDA

LFS

LFSEL

LFT

MISO

PH0

PH1

PH2

PH3

MOSI

MOTEIN

P-ENA

PKS

PKS1

Table 1 - 1 Signal Table (Part 2 of 2)

Meaning

ON/OFF Key

Electronic Occlusion Pressure

FM Connection Function Channel

FM Connection Control Channel

External 12V Supply (-)

External 12V Supply (+)

External 12V Supply (FM)

Air Sensor Clock

Air Sensor Data

Air Sensor Signal

Air Sensor Selection

Air Sensor Reset

Serial Data Output Interface

Serial Data Input Interface

Motor ON

Motor Control

Port Enable

Phase 0

Phase 1

Phase 2

Phase 3

Pump Cover Sensor

Pump Head Sensor 1

Mains Operation

Signal

SCK

TD-A0

TD-A1

TD-A2

TD-A3

TD6

TD7

TSA

TSCL

TD-E

TD-R/W

TD4

TD5

TSE

TSR

TSS

UBA, UBB

UBS

UBS-M

UMOT

UMOT-M

URTC

Meaning

Serial Data Lock

Text Display Address 0

Text Display Address 1

Text Display Address 2

Text Display Address 3

Text Display Enable

Text Display Read/Write

Text Display Data 4

Text Display Data 5

Text Display Data 6

Text Display Data 7

Drop Sensor Output

Drop Sensor Clock

Drop Sensor Receiver

Drop Sensor Regulation

Drop Sensor Control

Transmit Data

Supply Voltage for Alarm, On/Off Logic, RTC

Switched Operating Voltage UB

UBS Measurement Line

Supply Voltage of Motor Drive

UMOT Measurement Line

Supply Voltage Clock Module

When the unit is connected to mains the unit supply voltage is switched on for the duration of the switch-off delay time. If the microprocessor recognizes a sufficient mains voltage for the charging, the voltage supply is maintained. In this case only a battery balance is carried out, because a key was not pressed. The actual battery capacity and the battery operting hours are displayed in the LCD. The unit is switched off when the ON/OFF key is pressed for at least 2 seconds. Thereby the self-holding is triggered and the alarm latch is reset with a delay. After another 20 seconds the unit is switched off, because the pulses are missing.

If the Infusomat P is switched off in mains operation with the ON/

OFF key, the internal mains voltage is still present.

In mains operation the battery function is checked during the switch-on test. Therefor the charge and discharge current is

Infusomat P 2.0gb

Battery Operation

Alarm Circuit

Pump Unit

System Overview

1 measured and the charging of the battery is interrupted for the duration of the measurement.

The battery function is monitored by the following data: charge current, discharge current and time, and self-discharge time. In battery operation the battery function is checked during the switch-on test. The theoretical load condition is read from the clock module of the battery. Then the battery is connected to UBS and the voltage is measured. If the minimum requirements are not reached a battery alarm is activated.

The alarm generation consists of:

Standstill of pump due to switch-off of MS (motor circuit) and UMOT (motor operating voltage)

Audible alarm due to the drive of the buzzer or the loudspeaker via ALA-AK (control channel) or via ALA-UB

Optical alarm. Is displayed in the LCD and a separate LED display. Additionally the set rate flashes with AAA.A.

Staff call via the MFC staff call cable.

The user must check the optical and audible alarm during the switch-on test. An alarm must be activated to test the staff call alarm of the Infusomat P, e.g. open pump cover during operation.

The pump head is driven by a stepper motor. Each full step of the motor is realized by 5 microsteps. The motor is driven by an FET output stage. The function processor controls the motor with the

MS signal. A slot disc which is mounted on the pump head axle is scanned by two light barriers (PKS1 and PKS2 signal). Thereby the control microprocessor monitors the direction of rotation and speed of the pump head.

The pump head position is also determined with the PKS2 signal.

The motor can therefore be accelerated during the withdrawal phase. Thus a nearly pluse-free flow is realized in the lower delivery range (<100 ml/h). The total pump head cycles and running time are available in the service program under history data.

Infusomat P 2.0gb 1 - 7

Computer Interface

1 - 8

System Overview

Mechanical Occlusion Pressure:

The Infusomat P has a linear peristaltic pump. This pump has 12 slides which are driven by a camshaft.

When the pump cover is closed, the pump tube is squeezed (occlusion) by at least one of the slides, independent of the pump head position. The complete pump unit is mounted behind the front panel in the cabinet frame. The hinges and the locking bow for the pump cover are led through the front panel. The pump cover is automatically closed when the operating unit door is closed.

The slides are pressed against the pump cover by a spring system in the pump unit. Thereby a delivery pressure is realized and mechanically limited by the springs.

If the pressure limit is exceeded there is no volume delivery. The drop sensor activates an alarm. If one of the springs fails, the spring system will ensure that an unsafe condition cannot occur

(free flow). The two remaining springs ensure an appropriately high occlusion pressure.

Electronic Occlusion Pressure:

The electronic occlusion sensor is mounted on the output side of the pump. A spring pressure loaded slide is seated on the infusion line. An increase of pressure in the infusion line leads to a deflection of the coil core via the pressure slide. The depth of immersion is measured inductively. When a preset pressure threshold is reached the pump drive is switched off, and an alarm is activated.

The electronic occlusion pressure is a single channel circuit. In case of a failure, the mechanically limited maximum pressure can be reached.

Motor Switch-Off by Both Processors:

Function processor: MS signal to switch-off the motor drive. -

Control processor: MOTEIN signal to switch-off the drive of the motor operating voltage.

The Infusomat P is equipped with a computer interface. It can be connected to the optical interface or via the MFC service plug. To activate the computer operation please ask for a detailed description from B. Braun.

Until software version IFPC: DIANET

From software version IFPe, IFPE Dianet

Star

Infusomat P 2.0gb

Braun fluid manager system (fm system)

System Overview

The Infusomat P can be operated as a stand-alone unit or integrated in an intensive care unit, e.g. the B. Braun fluid manager system (fm system). It is integrated by simply snapping the unit into the system.

Mains supply and data communication are automatically connected. Thereby data acquisition and transmission to higher computer system levels are possible.

Internal Assignment

Fig.: 1 - 5

Infusomat P 2.0gb 1 - 9

1 - 10

System Overview

Accessories General

Designation Ord. No.

Mounting clip for drop chamber ”TK 2000” . . . . . . . . 3477 3223

Mounting clip for drop chamber ”Intrafix P” . . . . . . . 3477 3215

Universal adapter for drop sensor . . . . . . . . . . . . . . . . 0871 1747

Drop sensor, complete . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 578A

Short infusion pole. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0870 1644

Drop chamber holder . . . . . . . . . . . . . . . . . . . . . . . . . . . 3477 3088

Mains lead (200-240V~) . . . . . . . . . . . . . . . . . . . . . . . . 3450 2718

Mains lead (100-120V~) . . . . . . . . . . . . . . . . . . . . . . . . 3450 5423

Mains lead USA / CAN . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 5393

Universal Clamp

Universal clamp, complete. . . . . . . . . . . . . . . . . . . . . . . 3450 5857

Pole Clamp (rotating) . . . . . . . . . . . . . . . . . . . . . . . . . . 0871 8482

Infusomat P 2.0gb

2 - 6

2 -

Software

Software Update

Position

Digit

1 2 3 4 5 6 7 8 9

I F P E 1 3 0 0 3

Revision Level

Hardware Identification

Software Group

Infusomat P

Fig.: 2 - 1 Coding

Designation Ord. No.

Update-Kit IFPC02002 . . . . . . . . . . . . . . . . . . . . . . . . . 3450 6462

Update-Kit IFPe02003 . . . . . . . . . . . . . . . . . . . . . . . . . . On request

Update-Kit IFPE13003 . . . . . . . . . . . . . . . . . . . . . . . . . On request

(only units with controller board with loudspeaker)

MFC interface line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0871 1661

The higher digit always replaces the lower digit for the revision level, e.g. IFPE13003 replaces IFPE13002.

When the software group changes (IFPE13002) the unit functions are changed, too. Therefore unit users must be informed (e.g. instruct the user and exchange the instructions for use – software coding, e.g. IFPE is on the cover page of the instructions for use.)

Note

Mark the unit after having updated the software! The new software version must be clearly recognizable.

Only update from old to new software versions, never in reverse order (e.g. never update from IFPC02002 to IFPC02001!).

All units used in one ward should have the same software status and basic setup to avoid operator mistakes.

Note

Software updates must be reported to B. Braun for registration.

Observe the notes of the update program and the supplements!

Infusomat P 2.0gb 2 - 1

2 - 2

Software

Approved Software Versions IFPC02001

Basic software

(Must not be used any more. Please contact the Technical

Service of B. Braun).

IFPC02002

No optical staff call after power up (fluid manager system)

Optimized air sensor evaluation

Manual bolus volume limited to 99.9 ml

Optimized special bolus function

IFPe02003

Preselected volume and time counted down to 0

Long-time compensation of delivery rate

Interface changed to DIANET

Star

(not compatible with Dianet)

New special function Piggyback

New special function clock

Storage of alarms in case of malfunctions, which can be recalled in the service program menu 230

Tube selection menu

Calibration occlusion sensor

Tube update

IFPE13002

Only controller board with loudspeaker

(see „Controller Board“

See TSI-List for permissible check values

Alarm volume can be set

History function

IFPE13003

Optimized dose calculation

Infusomat P 2.0gb

Software

Error Messages and Alarms

7 Segment Display

Alarms of the function processor 80c535 are displayed in the text field of the LCD. Alarms of the control processor 68HC11 are displayed in the 7 segment display. The alarms help to troubleshoot unit malfunctions. As not all malfunctions can be considered, unit malfunctions with different messages, which are not listed, can be displayed, or there may be no message.

Detected unit alarms are displayed in the text field as ”Unit

Alarms” in the selected language. Additionally the error number is displayed in the text field.

Fig.: 2 - 2

110

111

112

113

106

107

108

109

116

117

118

119

120

Text Field

100

101

102

103

104

105

Table 2 - 1

Text Field

Description

defective RAM memory

UMOT cannot be switched on

UMOT still switched on despite overvoltage

UMOT still switched on despite MOTEIN=0

UMOT still switched on despite undervoltage

ON/OFF key pressed longer than 14 sec defective air sensor (calibration value?) defective program memory defective program flow different number of pump head cycles different keypad gaps between 80c838 and 68hc11 different program versions between 80c535 and 68hc11 defective program flow testbit!=0 out of switch-on test defective program memory - text defective program memory - text does not match with program reset during active operation defective program memory transit time ROM-test defective program memory tube parameters

Infusomat P 2.0gb 2 - 3

2 - 4

Software

FF07

FF08

FF09

FF10

FF12

FF14

FF16

FF17

7 Segment Display Description

FF01

FF02 dummy for test battery not present / missing battery current

FF03

FF04

FF05

FF06 defective RAM memory defective program memory - ROM test error 1 defective program memory - ROM test error 2 calibration data error from EEPROM pump head cycle not plausible failure / inaccuracy of system clock failure 100msec system clock reset during active operation no dynamic pressure sensor signal (EDB) defective temperature sensor defective membrane keypad (from IFPe02003) defective program memory tube parameters

Table 2 - 2

Control Microprocessor 68hc11

FFxx is displayed in the 7 segment display with flashing dots. FFxx is the error code.

Infusomat P 2.0gb

Software

Software Default Values Unit No.: _______________________

Standard Function

Special Functions

SM Menu

User Data

Menu Point

User Language

Alarm Type

Staff Call

Ward Identification

Drug 1 ... 9

Operating Alarms

Minimum Delivery Rate

Maximum Delivery Rate

Maximum Air Rate

Maximum Air Bubble

Dose Calculation

Default

Depending on Art. No.

Customer Setting

_______________________

Single stage _______________________

Static without OFF Alarm, without switch-on pulse

_______________________

”Ward Identification”

Drug 1 ... 9

0.1 ml/h

999.9 ml/h

1.5 ml/h

0.30 ml

Deactivated

Bolus

Standby

Deactivated

Activated

Drug Selection Deactivated

CC Mode

Deactivated

Occlusion Pressure Activated

Drop Control Deactivated

Piggyback

Deactivated

_______________________

_______________________ Battery Capacity Deactivated

Data Lock Deactivated

Alarm Tone

1) 3)

Deactivated

Contrast Deactivated

Clock

Activated

Interval Bolus Dose

Online Rate Setting

Off

Double Rate Entry

Tube Selection

Occlusion Pressure

Off

High

Contrast Optimum contrast

CC Address

Drug

Data Lock

Standby Time

Blank

Off

24h 00min

_______________________

From software IFPE

No longer available in software IFPe, IFPE

Not software IFPe

Infusomat P 2.0gb 2 - 5

Software

Calibration Data

Unit Specific Data

Menu Point

Drop Control

Alarm Tone

1) 3)

Dianet Mode Display

Bolus Key

Bolus Rate

Air Sensor Calibration Value

Tube group I

(dependent on tube)

Air Sensor Calibration Value

Intrafix Air P

(dependent on tube)

Scale Factor

(dependent on tube)

Occlusion Level, Low

Occlusion Level, High

History Function

DIANET Type No.

Unit No.

Operating Hours

Battery Hours

Number of Pump Head Cycles

60sec

999.9 ml/h

130 mV

Default

130 mV

50 (Intrafix Air)

Activated

Depending on unit

Customer Setting

_______________________

Must not be changed

_______________________

2 - 6

From software IFPE

No longer available in software IFPe, IFPE

Not software IFPe

Infusomat P 2.0gb

3 - 12

3 -

Service Program

Structure of the Service Program

Service Plug,

Inserted

Switch On

Standard Operation

(see operating flow diagram)

Short Display: software version, user language

Tube Type Selection

Special Functions

(see operating

flow diagram)

Group:

Unit Data

Software Version

100.0

Drug

110.0

Ward Identification

120.0

Tube Type

130.0

Serial Number

140.0

DIANET Type No.

150.0

Group:

History Data

Operating Hours

200.0

Battery Op. Hours

210.0

Pump Head

Cycles

220.0

Alarms

230.0

Service Program

Activated

Group:

Test

Air Sensor

300.0

Occlusion Sensor

310.0

Temperature Sensor

320.0

Group:

Unit Modification

Service Language

400.0

User Language

410.0

Alarm Tone

420.0

Staff Call

430.0

Special Function

440.0

450.0

Delivery Rate

460.0

Air Alarm

470.0

Dianet Mode

Display

480

Group:

Calibration

Occlusion Sensor

500.0

Scale Factor

510.0

Air Sensor

520.0

Comp. Head Volume

530.0

Occlusion Level

540.0

Pump Data

550.0

History

560.0

Only software IFPC

From software IFPe / IFPE

From software IFPE

Fig.: 3 - 1

Infusomat P 2.0gb 3 - 1

3 - 2

Service Program

Additional Functions with

Inserted Service Plug

Software Version and User Languages

Insert service plug into the MFC socket at the rear of the unit.

Switch on unit and keep the ON/OFF button pressed

(for max. 15 s).

The software version and user languages are displayed in the

LCD.

The unit is switched on when the ON/OFF button is released.

** appears in the LCD if the service plug is inserted.

Two LEDs are integrated in the service plug:

green = Power supply active

red = Alarm

The following conditions are active:

The operating alarms are muted.

All special functions are accessible (including the disabled).

The special functions are slightly modified. (Example: SM battery capacity has key for 0 min/32 min presetting).

The battery capacity display switches between the nominal and the actual capacity. If the maximum battery capacity is not reached ”?” will be displayed before the new nominal capacity.

The tube type will be displayed in the tube selection menu.

Disabling the Occlusion Sensor

The electronic pressure monitoring can be deactivated to check the mechanical occlusion pressure.

Select ”Occlusion Pressure” with the SM key.

Then select ”mechanical”.

Return to the main menu with END.

A too low pump speed is indicated in the display by ”Pressure

Alarm” with underlined stars.

The display "Pressure Alarm" with underlined questions marks indicates that no tube has been inserted.

1) From software IFPe / IFPE

Infusomat P 2.0gb

Start / Quit the Service Program

Fig.: 3 - 2

Fig.: 3 - 3

Unit Data

Infusomat P 2.0gb

Service Program

Activate the Service Program

Insert service plug into the MFC socket at the rear of the unit.

- ** appears in the display.

Select ”Service Program” with the SM key. When the service program is activated the red alarm LED flashes. The LED displays the code number of the selected group and function.

FUNCTION

END

GR+

FU+

Jumps to the initial function

Selects group

Selects function in the activated group

Activates the selected function or if necessary skips to the sub-functions with NEXT

Quit the Service Program

Press END in the main menu. - A data storage query is activated: ”Save Changes? Yes / No”.

Y / N terminates the service program.

Press END to jump to the last function.

Switch off the Infusomat P and remove service plug.

Note

Disconnect the Infusomat P from mains for at least 30 seconds after termination of the service program (memory is deleted). Then the unit can be switched on again.

Software Version

Select sub-functions with NEXT.

Function 100.0

The current software version is displayed in the LCD:

- User program version with date

- Language with text version. Further languages with (+).

- Service program version

- Service language with text version

- Tube type version

Return to the initial function with END.

3 - 3

Fig.: 3 - 4

3 - 4

Service Program

Drug Name Function 110.0

Memory for maximum 9 drugs and 20 characters per name.

Display the stored drug names with the NEXT key.

Delete displayed entry with CLR.

Press YES to modify a drug name:

Move cursor to character with NEXT.

Select new character from line 3 with << or >>.

Repeat the procedure for each character.

Return to the initial function with END.

Ward Identification Function 120.0

Enter and display of a ward specific unit identification. Permanent display if the unit is connected to mains and switched off.

Delete displayed entry with CLR. Press YES to enter modifications:

Move cursor to character with NEXT.

Select new character from line 3 with << or >>.

Repeat the procedure for each character.

Return to the initial function with END.

Tube Type

Function 130.0

There is only one tube type implemented in version IFPC02002.

This function is for future extensions.

Serial Number Function 140.0

The displayed serial number must correspond with the number on the unit type plate, as this number is used in the interface mode.

YES activates the entry mode. Enter via the numeric keypad.

YES stores the changed or new number.

Return to the initial function with END.

DIANET Type Number Function 150.0

The displayed serial number must correspond with the number on the unit type plate, as this number is used in the interface mode.

YES activates the entry mode. Enter via the numeric keypad.

YES stores the changed or new number.

Return to the initial function with END.

Only software IFPC

Infusomat P 2.0gb

Service Program

History Data

Bit

Code

15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

1 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0

Example for Alarm ”Pump Cover Open”

Battery empty (battery alarm)

Pump cover open

Drop alarm

Air alarm

Operating Hour Counter

OK activates the display.

Return to the initial function with END.

Battery Operating Hours

OK activates the display.

Return to the initial function with END.

Function 200.0

Function 210.0

Pump Head Cycles Function 220.0

Display of the pump head cycles (delivered volume).

OK activates the display.

Return to the initial function with END.

Operating Alarms Function 230.0

The last 20 operating alarms can be recalled.

They are displayed as 16 bit binary codes and each bit position can be set from 0 to 1.

OK activates the alarm display.

Display operating alarms -01 to -20 with the (+) and (-) key.

Delete the operating alarms with CLR.

Return to the initial function with END.

In addition the last unit alarm (GA) will be displayed from software version IFPe, IFPE.

8 to 14

Fig.: 3 - 5

Expired standby time

Interface alarm

KOR end alarm free

Operating alarm

Infusomat P 2.0gb 3 - 5

3 - 6

Test

Service Program

Air Sensor Function 300.0

After exchange check the function of the air sensor.

(see „Technical Safety

Inspection TSI“

(see „Test Equipment and Special Tools“

Press OK. The received signal amplitude is displayed as a measurement value.

(The test value with NEXT is not important).

Insert an infusion line filled with air and check the maximum permissible air value.

Insert an infusion line filled with fluid and check the minimum permissible water value.

Return to the initial function with END.

Pressure Sensor Function 310.0

Test Equipment

2.2 mm template

must be mechanically aligned

pg. 9 - 1)

Push in the bottom slide of the finger pump.

Press OK twice.

Open unit door.

Note the measurement value (actual value).

Insert the 2.2 mm template and close the unit door.

The new measurement value will be displayed. It must be 15 to 25 digits higher than the first value.

Return to the initial function with END.

If the 15 to 25 digits are not reached, the pressure sensor unit

(see „Occlusion Sensor“

Special functions to be selected, see

Temperature Sensor Function 320.0

Display of the measured temperature of both processors. Deviations are possible, the display is only for internal use.

OK activates the display.

Return to the initial function with END.

Infusomat P 2.0gb

Unit Modifications

Service Program

Service Language

English or German can be selected.

OK activates the function.

Select language with NEXT.

Acknowledge with YES.

Return to the initial function with END.

Function 400.0

User Language Function 410.0

Four user languages per language group are available (depending on software).

OK activates the function.

Select language with NEXT.

The language no. and text version are displayed.

Acknowledge with YES.

Return to the initial function with END.

Alarm Tone

Different alarm modes can be selected:

Single stage

Function 420.0

A ”10 minutes off alarm” can be selected.

In this mode the audible alarm is activated with a delay of 10 minutes.

The activation of the 10 minutes off alarm is only permissible, if:

the staff call is connected and

the Infusomat P has an attention label (label drawing no.

M007100000F04).

OK activates the function.

Select alarm tone with NEXT.

Acknowledge with YES.

Return to the initial function with END.

Infusomat P 2.0gb 3 - 7

3 - 8

Service Program

Fig.: 3 - 6

Staff Call Function 430.0

Select first, whether the switch-on pulse shall be activated (YES/

NO). The switch-on pulse is used to test the staff call line. Different staff call modes can be selected with the NEXT key:

Dynamic with OFF Alarm

Dynamic without OFF Alarm

Static without OFF Alarm

For further details see staff call line in the instructions for use.

An additional switch-on pulse (YES/NO) can be activated for each mode to test the staff call unit.

OK activates the function.

Select staff call type with NEXT.

Acknowledge with YES.

Return to the initial function with END.

Special Functions Function 440.0

Special functions can be activated in the service program, which are then available on the user interface. Deactivated special functions will not be displayed. The SM softkey will not be displayed in standard operation, if all special functions are deactivated. -

Fig.: 1 - 1

OK activates the function.

Select special functions with NEXT.

Activate / deactivate the respective function with YES/NO.

Return to the main menu with END.

Infusomat P 2.0gb

Service Program

Menu Function 450.0

The availability of menus on the user interface can be set.

Double rate entry

Online rate entry

Interval bolus

Tube selection

OK activates the function.

Activate / deactivate the decimal function with NEXT.

Acknowledge with YES.

Return to the main menu with END.

Delivery Rate Function 460.0

The maximum and minimum delivery rates can be set. Range of adjustment of the delivery rate: 0.1 to 999.9 ml/h

OK activates the function.

Select the min./max. delivery rate with NEXT.

Acknowledge with YES.

Enter value with a numeric key.

Acknowledge with OK.

Return to the initial function with END.

Air Alarm Function 470.0

The air sensor sensitivity of the air rate alarm in ml/h (total air alarm) and of the maximum air bubble in ml (single bubble) can be adjusted.

Setting range air rate: 0.5 to 3.5 ml/h

Setting range air bubble: 0.01 to 0.3 ml/h

OK activates the function.

Select air rate (ml/h) or air bubble (ml) with NEXT.

Acknowledge with YES.

Enter value with a numeric key.

Acknowledge with OK.

Return to the initial function with END.

3 - 9

Calibration

3 - 10

Service Program

Dianet Mode Display Function 480.0

When operated with DianetStar the respective DianetStar-mode

(CA, CC, CD) with address 01, e.g. mode CA and address 01 is displayed by: “###CA01###”.

The duration of the display after the last data transmission can be set between 0 and 255 seconds.

All safety-relevant parameters are set by the manufacturer. If these parameters are changed, a new calibration must be performed with calibrated test equipment.

Occlusion Sensor Function 500.0 *

Measurement and setting of the zero value of the occlusion sensor, Ord. No.: 3450 7353.

Press the OK key twice.

Press the Align key.

Open the unit door and remove tube.

Check the occlusion sensor for cleanliness and function

(briefly operate the sensor and check whether the displayed measurement value changes).

Wait until the displayed measurement value does not change any more (+/- one digit). The measurement value must be between 150 and 220 digits.

Acknowledge the measurement value with YES.

Return to the initial function with END.

It is not allowed to enter the zero point value via the keypad.

Occlusion Sensor Function 500.0 **

Measurement and setting of the zero value "3" of the occlusion sensor, Ord. No.: 3452 0589. Calibration

(see „Occlusion Sensor“

Pay attention to the indications in

Press the OK key twice.

Press the Align key.

Open the unit door and remove tube.

Check the occlusion sensor for cleanliness and function

(briefly operate the sensor and check whether the displayed measurement value changes).

Table 4 - 1 „Compatibility List“

* Until software IFPC

** From software IFPe / IFPE

Infusomat P 2.0gb

Service Program

Wait until the displayed measurement value does not change any more (+/- one digit). The measurement value must be between 250 and 400 digits.

Acknowledge the entry with YES.

Return to the initial function with END.

It is not allowed to enter the zero point value via the keypad.

Scale Factor Function 510.0

The scale factor can be set in the limits between 40 and 99 digits for each tube type. Every digit step is equivalent to a 0.5 % modification of the delivery rate. An increase of the scale factor reduces the pump speed, and a decrease increases the pump speed.

Press the OK key twice to activate the function.

Select the tube type with the NEXT key.

"Yes" activates the function for the selected tube type.

The value can be changed with the entry keypad.

Acknowledge the entry with OK.

Return to the initial function with END.

Quit the service program and save changes with YES.

Switch on unit and check the delivery rate

(see „Delivery Accuracy“

Alignment or check of the air sensor value (alarm threshold)

pg. 8 - 4)

If necessary repeat the delivery rate measurement.

Air Sensor Function 520.0

(see

„Air Sensor“

pg. 4 - 18)

Note

The value is dependent on the tube type.

Press OK twice and then YES to activate the function.

Press OK again to activate the air sensor value.

The value can be changed with the entry keypad.

Acknowledge the entry with YES.

AIR SENSOR IS SET acknowledges the entry.

Return to the initial function with END.

Quit the service program and save changes with YES.

Compensation Head Volume Function 530.0 *

Only for test purposes at the manufacturers. The compensation of the head volume must always be activated.

3 - 11

3 - 12

Service Program

Occlusion Level Function 540.0

Setting of the occlusion threshold values for the occlusion levels

"low" and "high".

Press the OK key twice to activate the function.

Select the occlusion level with NEXT.

YES activates the entry mode.

Enter the pressure value via the numeric keys (pay attention to the displayed limit values!).

Press the YES key to take over the settings.

Return to the initial function with END.

Pump Data Function 550.0

Note

Compatibility between controller board and pump must be checked before acknowledging. Only press YES if pump corresponds to controller board.

History Function 560.0 *

The history function can be activated or deactivated.

Press the OK key twice to activate the function.

Select the history function with NEXT.

ON activates the function. The history protocol memory is initialized (the actual software version and the serial number are registered).

Press the OFF key to deactivate the function. The history protocol memory is deleted.

Return to the initial function with END.

* Only software IFPC

* From software IFPE

Infusomat P 2.0gb

4 - 20

4.1 Mains Fuses

4.2 Battery

Fig.: 4 - 1

Infusomat P 2.0gb

4 -

Unit Elements

M4x8

Designation Ord. No.

Fuse T 0.16 A for 200 / 230 / 240 V

(10 pcs.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3477 2847

Fuse T 0.315 A for 100 / 110 / 120 V

(10 pcs.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3477 0534

Fuse holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 0979

Note

Only use recommended fuses.

Exchange

Press the expansion clamps at the fuse holder on the recessed mains plug with a screw driver in direction of the arrows and pull out fuse holder.

Replace blown fuse and press in fuse holder. Only use recommended fuses.

Check

Safety check, functional check.

Designation Ord. No.

Battery incl. connector 1.2 AH / 7.2 V and holder. . . . 3450 2556

Exchange

Switch off unit and disconnect from mains.

Loosen screw, open the cover of the battery compartment and remove battery.

Pull off the battery connector.

Assembly is done in reverse order.

After having exchanged the battery the Infusomat P must be connected to mains, before switching on the unit. Thereby the charge and discharge currents are aligned.

Charge battery (16 h).

Note

Defective batteries must be orderly disposed of, e.g. send back to

B. Braun

(see „Return of Spare Parts“

pg. 0 - 7)

Check

Perform switch-on test in battery operation and check the battery running time, if necessary.

4 - 1

4 - 2

Unit Elements

4.3 Door Lock

S M 3x6

Designation Ord. No.

Door lock complete with push button . . . . . . . . . . . . . 3450 5601

Spring holder for door lock . . . . . . . . . . . . . . . . . . . . . . 3450 5440

Mounting for door lock . . . . . . . . . . . . . . . . . . . . . . . . . 3477 2790

Exchange

Open door and unlatch the spring holder.

Remove coutersunk screw and press out the mounting by pressing the holder for the door lock.

Remove door lock in an upward direction and exchange.

Assembly is done in reverse order.

Check

Pump unit check (only mechanical occlusion pressure).

Fig.: 4 - 2

Spring Holder

IP 013

Infusomat P 2.0gb

Unit Elements

4.4 Pump Cover

Hinge Pin for

Pump Cover

Fig.: 4 - 3

Pump Cover

Hinge Pin for

Pump Cover Lever

Torsion Spring

IP 014

Designation Ord. No.

Pump cover with lock . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 1916

Blind plug 7.1 mm (10 pcs.) . . . . . . . . . . . . . . . . . . . . . 3477 3207

Torsion spring in lever/pump cover (5 pcs.) . . . . . . . . 3477 3363

Torsion spring for pump cover (5 pcs.) . . . . . . . . . . . . 3477 3355

Lever (pump cover). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3477 4092

Hinge pin for pump cover . . . . . . . . . . . . . . . . . . . . . . . 3477 3967

Hinge pin for pump cover lever. . . . . . . . . . . . . . . . . . . 3450 5725

Exchange

Tools: Pin punch 1.8 mm, pin punch 6 mm, 2.2 mm template

Open door and remove hinge pin with pin punch (1.8 mm) from below. Do not lose the torsion spring.

Disassemble pump cover.

Insert the torsion spring in new pump cover. Insert the hinge pin from the top with a pin punch (6 mm).

Check the occlusion sensor with 2.2 mm template in the service program, and align, if necessary.

Check

Safety check, pump unit check.

Infusomat P 2.0gb 4 - 3

4 - 4

Unit Elements

4.5 Pump Housing Designation Ord. No.

Pump housing, (cpl.). . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3390

Exchange

Remove 4 tamper-proof caps by piercing a screwdriver through the caps.

Loosen the screws.

Remove the pump housing.

Note

Do not use the pump housing again, but replace it by a new one.

Fig.: 4 - 4

Pump Housing

Tamper-Proof Caps

IP 038

Infusomat P 2.0gb

4.6 Housing and Handle

PT5.0x16

Unit Elements

O-Ring

Designation Ord. No.

Housing Labelling

German . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 1851

French . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 1851

Dutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 1851

Italian. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 1851

English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3382

Spanish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3382

Danish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3404

Norwegian . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3404

Swedish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3404

Finnish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3404

Portuguese. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3382

Czech . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3358

Polish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3358

Turkish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3382

Foot stand complete with rubber feet . . . . . . . . . . . . . 3450 5415

Rubber feet (20 pcs.) . . . . . . . . . . . . . . . . . . . . . . . . . . . 3477 3096

Unit handle with O-rings and PT screws . . . . . . . . . . . 3450 3450

Exchange

Remove battery

the occlusion sensor (3451 0589) has also to be installed

Loosen 4 screws from the foot stands and remove foot stands.

Remove the safety seal from the rear panel, break tamperproof cap and remove screw.

Slidly widen the sides at the bottom of the housing and pull off to the top.

Lay the unit on the front side and assemble in reverse order.

Safety seal the rear panel screw after functional check.

Check

Safety check.

4 x M4x8

Fig.: 4 - 5

Infusomat P 2.0gb 4 - 5

Unit Elements

4.7 Controller Board

Cable Output Motor

Air Sensor Connector

Flex Cable LCD Module

Motor Connector

Occlusion Sensor

Connector

Rear Panel

Connector

Designation Ord. No.

Distance sleeve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3366

Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3447

Loudspeaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 8848

Controller board with buzzer, raw material No. 3810 7660, software IFPC, can be updated to IFPe, if desired.

**Language Group* New Part Exchange**

Ord. No.:3450 2041 Ord. No.:3488 0895

Ord. No.:3450 2050 Ord. No.:3488 0909

Ord. No.:3450 2068 Ord. No.:3488 0917

Ord. No.:3450 2076 Ord. No.:3488 0925

Ord. No.:3450 2084 Ord. No.:3488 0933

Fig.: 4 - 6

Reed Sensor

Connector

Battery Connector

Loudspeaker / Buzzer

Press snap-in pin together

Controller board with loudspeaker, volume control and history function, raw material no. 3810 8003, software IFPE:

**Language Group* New Part Exchange**

Ord. No.:3450 8767 Ord. No.:3488 0941

Ord. No.:3450 8775 Ord. No.:3488 0950

Ord. No.:3450 8783 Ord. No.:3488 0968

Ord. No.:3450 8791 Ord. No.:3488 0976

Ord. No.:3450 8805 Ord. No.:3488 0984

CAUTION

The controller boards (raw material no. 3810 7660 and 3810 8003) are not compatible.

Controller Board

Raw Material No.

3810 7660

3810 7660, with update

3810 8003

Table 4 - 1 Compatibility List

IFPC

IFPe

IFPE

Software Buzzer

Buzzer

Loudspeaker

Occlusion Sensor

Order No.

3450 7353

Calibration Device Finger Pump, cpl.

Order No.

3450 1746

3452 0589

3452 0589 yes yes

3452 0597

* Language Group:

A German, French, Dutch, Italian

B English, Dutch, Spanish, English

C Danish, Norwegian, Swedish, Finnish

D Spanish, Portuguese, English, Turkish

E Czech, Polish, Hunguarian, English

4 - 6 Infusomat P 2.0gb

Infusomat P 2.0gb

Unit Elements

If the controller board (raw material no. 3810 7660) is to be replaced by the new controller board (raw material no. 3810 8003)

(see

„Occlusion Sensor“

. An exchange in reverse order is not permitted.

Exchange

Remove battery

Press snap-in pin together at the distance sleeves and remove the board carefully.

Pull off connector (see figure).

Exchange the board or buzzer.

Assembly is done in reverse order. Be careful with the optical components. Insert the board into the lower guide parallel to the base plate. (Otherwise problems with the optical interface can occur.)

Note

If ”Calibration Defective” is displayed after having exchanged the controller board, check that the correct board (risk of mix-up) was assembled.

Check

Safety check, functional check.

4 - 7

Fig.: 4 - 8

4 - 8

Unit Elements

4.8 Rear Panel Designation Ord. No.

Rear panel with screws (M3) and seal . . . . . . . . . . . . . 3450 1860

Cover for optical interface. . . . . . . . . . . . . . . . . . . . . . . 3477 3164

Strip seal for rear panel . . . . . . . . . . . . . . . . . . . . . . . . . 3477 3142

MFC connector board . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3374

Potential equalization bolt . . . . . . . . . . . . . . . . . . . . . . 3477 0550 fm recessed plug (3 pin) . . . . . . . . . . . . . . . . . . . . . . . . 3477 3177

Screw 30x8 for fm recessed plug (20 pcs.). . . . . . . . . . 3477 3185

U Washer 3.2 (20 pcs.) . . . . . . . . . . . . . . . . . . . . . . . . . . 3477 3193

Mains module 200/230/240 V . . . . . . . . . . . . . . . . . . . . 3450 1886

Mains module 100/110/120 V . . . . . . . . . . . . . . . . . . . . 3450 1894

Mains module 230 V . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 190A

Drop sensor socket incl. cable and plug . . . . . . . . . . . . 3450 1878

Fig.: 4 - 7

No.

Signal Name

Pin 1 Uext-

Function

Input of external supply voltage, connection of shield

Pin 2 not assigned

Pin 3 GND

Pin 4 Staff call

Pin 5 Ub

Pin 6 MFC-KAD

Pin 7 Emergency Off

Pin 8 MFC-FAD

Pin 9 Tx

Pin 10 STB

Reference level 0V

Output open collector or standard

74HC level each with 220

Ω-series resistance

Output supply voltage

Analogue input K

Input interface

Analogue input F

Transmit line interface

Output with 470

Ω-series resistance, activation of MFC circuit

Table 4 - 2 MFC Pin Assignment

Infusomat P 2.0gb

Rear Panel

Unit Elements

No.

Pin 11 Rx

Signal Name

Pin 12 Uext+

Function

Receive line interface

Input of external supply voltage

Table 4 - 2 MFC Pin Assignment

Exchange Rear Panel

Remove battery

Pull off the rear panel connectors and loosen both screws on the unit bottom.

Fig.: 4 - 9

M4x8

Infusomat P 2.0gb 4 - 9

Unit Elements

M18

Exchange MFC Connector Board

Tools: Special socket spanner M18

Remove nuts at the fm recessed plug (red/blue).

Pull off the connector to the mains power supply and drop

sensor, see

Fig.: 4 - 7

Loosen the MFC socket with special socket spanner M18.

Assembly is done in reverse order.

Fig.: 4 - 10

Cable, Red Cable, Blue

PT 3x8

2x M4 each

Fig.: 4 - 11

2x M6

4 - 10

Exchange fm Recessed Plug

Loosen screws and nuts.

Note

The new recessed plug must be slightly moveable after assembly.

Exchange Potential Equalization Bolt

Remove nuts with ring spanner.

Exchange the bolt.

Infusomat P 2.0gb

Unit Elements

4.9

Power Supply Unit

Fig.: 4 - 12

3 X Torx M3x10

Front Panel

Fig.: 4 - 13

Infusomat P 2.0gb

Tamper-Proof Cap

Exchange Mains Module

Tools: Screw driver Torx T10

Loosen 3 screws and remove the power supply unit.

Note

The voltage selection for switchable power supplies is at the fuse element.

Exchange Drop Sensor Socket

Loosen nut and exchange the drop sensor socket.

Safety lock with Sicomet 50.

Make ground connection.

Check

Safety check, functional check.

Snap-In Pin

(Rear Side)

Reed Sensor

(Rear Side)

Snap-In Pin

(Rear Side)

IP 023

Designation Ord. No.

Front panel without clamp lever and torsion spring . . 3450 2092

Circular seal 45 mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3477 3126

Tamper-proof caps 10 mm (50 pcs.) . . . . . . . . . . . . . . 3477 3134

Cover Ø 6.4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3412

Clamp lever with torsion spring and pin 4x20 . . . . . . 3450 3420

Torsion spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3439

Reed sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 1754

Exchange

Tools: Pin punch

Remove battery

Disassemble pump cover

(see „Pump Cover“

pg. 4 - 3)

Disassemble pump housing

(see „Pump Housing“

Press reed sensor out of the holder on the rear side, see

pg. 4 - 4)

Remove countersunk screws by piercing a screwdriver through the caps to loosen the countersunk screws.

Fig.:

4 - 14

Press both snap-in pins inwards (rear side top and bottom).

Then remove the front panel to the front.

Exchange the flow inhibitor, i.e. pull straight pin with M3 screw. Prior to assembly slightly grease the plastic surfaces with Molikote Platislip PG 602 grease.

4 - 11

Unit Elements

Insert circular seal. Assembly is done in reverse order. Snapin pins manually. Insert reed sensor and seat the cables firmly with cable ties.

Note

Always use a new pump housing.

Check

Safety check, pump unit check.

4 - 12 Infusomat P 2.0gb

Unit Elements

4.10 Pump Unit

Motor

Snap-In Pin

M3x6

Pump Unit

Reed Sensor

Fig.: 4 - 14

Infusomat P 2.0gb

Cable Tie

Designation Ord. No.

Note

When replacing the finger pump adhere to

Table 4 - 1 „Compatibility List“

Finger pump (without motor) including pump, . . . . . 3450 1746 pump cover, seal membrane and occlusion sensor

board, software IFPC

(installed up to unit serial no. 5505)

Finger pump (without motor) including pump, . . . . . 3452 0481 pump cover, seal membrane and occlusion sensor

board, software IFPe, IFPE

(installed from unit serial no. 5506)

Finger pump (without motor and board) . . . . . . . . . . 3452 0597 incl. pump, pump cover, and seal membrane

Motor with pinion for finger pump . . . . . . . . . . . . . . . 3450 1924

Exchange

Remove battery

Disassemble front panel

(see „Front Panel“

pg. 4 - 11)

Loosen motor screws, pull off the motor connector and remove motor from pump unit.

Note

Do not loosen the assembly screw on the lower occlusion sensor board! Otherwise the pump has to be calibrated with the 2.2 mm template.

Pull off the connector from the controller board.

Press down snap-in pins (from the inside) and tilt the pump forward and unhinge.

Assembly is done in reverse order.

CAUTION

Due to the improved occlusion sensor the finger pump to be installed is dependent on the controller board and the software.

Note

Be sure that the cable of the reed sensor and air sensor do not hinder the function of the occlusion sensor and the monitoring of the motor speed (slot disc).

4 - 13

4 - 14

Unit Elements

The complete pump unit (pump without motor, pump cover, membrane, boards) was calibrated by B.Braun. After a complete exchange the unit data and user data must be entered in the service program again as the data memory is on the pump board:

Enter unit and user data in the EEPROM.

Serial number according to the type plate

DIANET type number according to the type plate

If necessary enter:

Drug name

Ward identification

Alarm tone

Delivery rate min./max.

Air alarm: air bubbles in ml and air rate in ml/h respectively

User language

Special functions (ON/OFF)

Staff call type

Note

If data is not entered, ”Calibration Defective” may be displayed after the unit is switched on again.

After ending the service program save the data.

The counters for operating hours, battery operation and pump head cycles are reset to zero when the pump unit is exchanged. If

”Calibration Defective” is displayed, select the service program and quit with ”Save? Yes”.

Check

Safety check, pump unit check.

Infusomat P 2.0gb

Unit Elements

4.11 Occlusion Sensor

Light Barrier

Board

Screw (1)

Test Equipment Ord. No.

Template 2.2 mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0770 5034

Calibration device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0770 501A

Designation Ord. No.

Note

When replacing the occlusion sensor pay attention to

Table 4 - 1

„Compatibility List“

„Pressure Sensor Function 310.0“

Occlusion sensor (cpl.) . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 7353

Software IFPC

(installed up to unit serial no. 5505)

Occlusion sensor (cpl.) . . . . . . . . . . . . . . . . . . . . . . . . . . 3452 0589

Software IFPe, IFPE

(installed from unit serial no. 5506)

(only delivered when a pressure calibration device is available)

Exchange

CAUTION

The occlusion sensor unit is mechanically very sensitive. It must not be dismounted, which means that the occlusion sensor board and the spring element must not be detached from the occlusion sensor support (plastic part). Make sure that the movement of the coil core inside the coil is not hindered.

Plain

Washer

Serrated Lock Washer

Screw (2)

Fig.: 4 - 15

Occlusion Sensor Board

Do not loosen screw!

Occlusion Sensor cpl.

The occlusion sensor consists of the light barrier board with EEP-

ROM and the occlusion sensor board with holder. Coil core and bending element are screwed on this holder. Both boards are connected via a flat cable.

Dismount the rear panel

(see „Rear Panel“

pg. 4 - 8)

pg. 4 - 13)

Pull off the connecting cable to the microprocessor board.

Loosen and remove screw (1) of the light barrier board.

Loosen screw (2) of the occlusion sensor and remove it together with plain washer and serrated lock washer. Then remove the occlusion sensor with occlusion sensor board and light barrier board.

Mount new occlusion sensor.

CAUTION

The occlusion sensor to be installed is dependent on the controller board and the software.

Infusomat P 2.0gb 4 - 15

4 - 16

Unit Elements

Note

Make sure that the occlusion sensor slide can smootly run in the guides and that the coil core can move inside the coil.

Calibrate occlusion sensor: a) Call the pressure display in the service program

(see

(see „Occlusion Sensor Function 500.0 *“

pg. 3 - 6)

b) Loosen hexagon socket screw (M 3x6) on the occlusion sensor unit (with a 2.5 mm Allen key).

c) Push the occlusion sensor unit with board slightly forward or backward.

d) Tighten the Allen screw.

e) The new measurement value will be displayed (repeat if necessary until the value is increased by 15 to 25 digits).

f) After calibration return to the initial function with END.

- Select SAVE NO. (Do not operate the YES key.) g) Switch off the unit.

Assembly is done in reverse order.

After a complete exchange the unit data and user data must be entered in the service program again as the data memory is on the lightbarrier board.

Enter unit and user data in the EEPROM.

Serial number according to the type plate

DIANET type number according to the type plate

If necessary enter:

Drug name

Ward identification

Alarm tone

Delivery rate min./max.

Air alarm: air bubbles in ml and air rate in ml/h respectively

User language

Special functions (ON/OFF)

Staff call type

Note

If data is not entered, ”Calibration Defective” may be displayed after the unit is switched on again.

Calibrate occlusion sensor, Ord. No. 3450 7353:

Call function 500 in the service program

pg. 3 - 10)

Infusomat P 2.0gb

Unit Elements

10. Calibrate occlusion sensor, Ord. No. 3452 0589:

Note

To calibrate the occlusion sensor, Ord. No. 3452 0589 calibration weights are required. An alignment with infusion lines is not permitted.

a) Clean the pump front side.

b) Place the Infusomat P without mains lead and drop sensor and the service plug inserted horizontally (front facing upwards) in the cellular packing of the calibration device.

(see „Pressure

Sensor Function 310.0“

m) Call function 500 in the service program

pg. 3 - 6)

d) Activate the calibration function with "Align".

e) Select calibration value low "1" by pressing ">>".

f) Open the pump cover.

g) Fasten the holders for the calibration weights under the pump cover and let snap in at the locking bow.

h) Position weight 1 (100 g) for calibration value low "1"

(1.04 N) carefully on the occlusion sensor. The weight must be placed without any friction in the holder.

i) Acknowledge calibration value low "1" with ">>" and set calibration value high "2" with weight 3 (166g).

j) Acknowledge calibration value high "2" by pressing ">>" and remove weight.

k) Acknowledge calibration value "3" "Zero point" with

"Yes".

l) Remove the holder.

Note

If the calibration values are known the values can also be entered manually.

(see „Occlusion

Sensor Function 500.0 **“

Occlusion Pressure (Occlusion Sensor)“

pg. 3 - 10)

n) Open the data entry window with "yes".

o) Select Calibration value low "1" and Calibration value high "2" by pressing “<<" and “>>". Enter the calibration values via the keypad and acknowledge with ”yes”.

p) Quit function in the service program and save data.

q) Register the changed pressure values in the unit book.

4 - 17

4 - 18

Unit Elements

4.12 Air Sensor

Fig.: 4 - 16

Air Sensor r) Check the electronic occlusion pressure

(see „Electronic

12. Check the electronic occlusion pressure

pg. 8 - 3)

11. Quit function in the service program and save data.

(see „Electronic Occlusion Pressure (Occlusion Sensor)“

pg. 8 - 3)

Check

Safety check, functional check.

Designation Ord. No.

Air sensor incl. connector . . . . . . . . . . . . . . . . . . . . . . . 3450 193A

Exchange

Remove battery

Dismount housing

Dismount controller board

(see „Controller Board“

Disassemble front panel

(see „Front Panel“

pg. 4 - 11)

Press the complete sensor from behind and out of the frame.

Insert new sensor and seat the cables firmly with cable ties.

Note

Be sure that the cables of the reed sensor and air sensor do not hinder the function of the occlusion sensor and the monitoring of the motor speed (slot disc).

Check

After exchange of the air sensor:

Check the air value, please refer to the TSI-list

Check the water value; please refer to the TSI-list

Check the calibration value (alarm threshold) and adjust if necessary; refer to the TSI-list

Safety check, functional check.

Infusomat P 2.0gb

Unit Elements

4.13 Operating Unit

Support Plate

Zero Force Insertion Connector

Flex Cable, Preformed

LCD Module

Designation Ord. No.

Membrane keypad with support plate and seal . . . . . 3450 1800

LCD module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 1819

Flex cable, preformed . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 8830

Frame incl. pressure spring and magnet . . . . . . . . . . . 3450 1835

Flexible cable 42 mm (5 pcs.) . . . . . . . . . . . . . . . . . . . . 3477 3347

Hinge unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 5571

Hinge pin (3 mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 5580

Magnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 5849

Exchange

Tools: Screw driver Torx T6

Remove battery

Disassemble the door lock.

Loosen countersunk screw and bridge.

Remove tamper-proof caps (6 pieces) on the door frame by piercing a screwdriver through the caps to loosen the countersunk screws.

Unlatch the zero force insertion connector and loosen the flex cable.

Fig.: 4 - 17

Frame Operating Unit

Fig.: 4 - 18

Hinge Pin

6 x PT2.5x14

Note

The position of the flex cable must not be changed, i.e. the preformed section must be in the hinge area (pivot). Mark the cable, if necessary.

Disassemble either LCD module or support plate with membrane keypad or door hinge pins respectively and exchange the door frame.

Assembly is done in reverse order. Pay attention to the correct direction of the door hinge pin during assembly.

Note

Do not kink either of the flex cables. Push the contacts to the stop of the zero force insertion connector and lock in same position.

Check

Electrical safety, functional check, pump unit check.

Infusomat P 2.0gb 4 - 19

4 - 20

Unit Elements

4.14 Barcode Label Designation Ord. No.

Barcode label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 9070

(see „Order Form“

(see „Procedural Instructions for Inspection“

pg. A - 2)

Exchange

Remove old barcode label, if existing.

Clean the adhesion surface with an alcoholic cleaning agent and let dry.

Loosen barcode label from the base material and stick it on.

Note

Destroy the type plate delivered.

Check

Check that serial number and pump symbol in the plain text field of the barcode label correspond with the type plate on the pump of the Infusomat P.

Barcode Label

Fig.: 4 - 19

4.15 Frame with Seal Designation Ord. No.

Frame with seal plate . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 1770

Exchange

Disassemble all parts as described before and exchange the frame with seal plate.

Check

Electrical safety, functional check, pump unit check.

Infusomat P 2.0gb

5 - 2

5 -

Checks after Repair

Depending on the work carried out, perform the relevant check blocks (1., 2., 3 and / or 4.).

1. Visual Inspection

❒ OK after visual inspection

2. Safety Inspection

As per IEC/EN

60 601-1

❒ Mains voltage ____ V AC

❒ Protective conductor resistance incl. mains cable < 0.2

Ω ____

❒ Insulation resistance

Switch on Unit:

❒ Self-test

❒ Control lamps

Compare with Display:

❒ Set delivery rate

>> 2 M

Ω ____

❒ Earth leakage current

3. Functional Inspection

Battery Test:

4. Pump Unit Inspection

Room Temperature 20-28° C

Electronic Occlusion Pressure:

❒ Check alarm with switchoff pressure low / high

❒ Zero value setting

Service program function

500.0

mains

❒ Switch on in battery mode and check self-test

Mechanical Occlusion Pressure

Air Sensor:

❒ 0.4 ml air bubbles alarm

❒ Air value

❒ Water value

❒ Calibration value (alarm threshold), adjust if necessary

Values see TSI

❒ Flow inhibitor

Pressure check

≥ 0.8bar no free flow

❒ Delivery accuracy

Drop Sensor:

❒ Simulate occlusion alarm

(alarm with closed roller clamp)

❒ Simulate free flow (alarm)

❒ Staff call

❒ Alarm suppression

Observe the procedure information

pg. 8 - 1)

Infusomat P 2.0gb 5 - 1

Checks after Repair

For your notes:

5 - 2 Infusomat P 2.0gb

6 - 2

6 -

Maintenance

It is recommended every 2 years. In addition to the technical safety inspection, perform the following inspection points:

Check the rubber feet and if necessary exchange.

Check easy running of the pump cover, lock mechanism and door.

Check easy running of the flow inhibitor, clean and if necessary exchange pressure springs.

Check seal membrane and if necessary exchange.

Check the drop sensor optic and spring mechanics and clean, if necessary.

Open unit. Internal visual inspection. Clean the seal surfaces and if necessary exchange seal strip.

Check mechanical occlusion pressure and if necessary calibrate.

Check electronic occlusion pressure and if necessary calibrate

(see „Occlusion Sensor“

9. Assemble and seal unit ready for operation.

Infusomat P 2.0gb 6 - 1

Maintenance

For your notes:

6 - 2 Infusomat P 2.0gb

7 - 2

7 -

Technical Safety Inspection TSI

Index c

(Kopiervorlage - Gerätedokumentation beifügen)

Checklist for Technical Safety Inspection – Every 24 Months

Unit: Infusomat P

Manufacturer: B. Braun Melsungen AG

Observe the service manual and the instructions for use. All measured values are to be documented.

Accessories used should be included in testing. Make exclusive use of calibrated measuring instruments.

Article No.

Unit No.

Year of Procurement

User

1. Visual Inspection 2. Safety Inspection 4. Functional Inspection

❒ Cleanliness, completeness, damage

❒ Pump sealing diaphragm

❒ Softkeys, rubber feet

❒ Control unit, lock mechanism, pump cover

❒ Flow inhibitor

❒ Mains cable and mains plug as per IEC/EN60601-1

❒ Check mains voltage ____ V AC

❒ Protective conductor resistance

Switch on Unit:

❒ Self-test

❒ All symbols in LCD

❒ Control lamps incl. mains Compare with Display: cable < 0.2

❒ Set delivery rate

❒ Insulation resistance ❒ Set volume

>> 2 M

❒ Set time

❒ Earth leakage current ❒ Press every key once connector

❒ MFC connector incl. MFC cable

❒ Drop sensor line and plug connector

❒ Check voltage values

100/110/120 V = T 0.315 A

200/230/240 V = T 0.16 A

3. Accessories Used

❒ MFC staff call lead

❒ _______________________

❒ Switch mains/battery/mains

❒ Switch on in battery mode and check self-test

Air Sensor:

(Check with Intrafix Air P Ord.

No. 0406 2957, in temperature range 20°C...25°C)

❒ 0.4 ml air bubbles alarm

❒ Air value max. 65mV

❒ Water value min. 455mV

❒ Alarm threshold = 130 mV check and if necessary enter

Drop Sensor:

❒ Simulate occlusion alarm with closed roller clamp

❒ Simulate free flow (alarm)

Electronic Occlusion Pressure:

❒ Check alarm with switchoff pressure low and high

Mechanical Occlusion Pressure:

❒ max. 2.9 bar

❒ > 1.8 bar

____ bar

❒ Staff call

❒ Pump cover alarm

❒ Alarm suppression

❒ Flow inhibitor

pressure check up to 0.8bar no free flow

❒ Check delivery accuracy according to service manual

CAUTION: Charge battery!

Inspection performed by: Applied infusion line

Type: ___________________ Manufacturer: ___________________

Test Result: Defects found which could endanger patients, users or third parties:

Yes No

Measures to be taken: Repair

___________________

Unit handed over to/on:

Special Features / Documentation: Date / Signature:

Next deadline:

M664 00 00 92 F04 C 38912201

Infusomat P 2.0gb 7 - 1

Technical Safety Inspection TSI

For your notes:

7 - 2 Infusomat P 2.0gb

8 - 6

8 -

Procedural Instructions for Inspection

1. Visual Inspection

2. Electrical Safety Inspection as per IEC/EN60 601-1

Operating unit, lock mechanism, pump cover, seal membrane, flow inhibitor. Door lock: easy opening and closing, correct top and bottom locking.

Pump cover must automatically open when the unit door is opened.

Protective Conductor Resistance

Protective conductor resistance < 0.2

Ω. incl. mains lead.

Measurement points:

Potential equalization bolt

Bolt for door lock

Unit housing: a) If the unit is not sealed countersunk screw at the rear of the unit.

b) If the unit is sealed, remove lacquer from one of the holes in the foot stands.

Note

Do not use the foot stand assembly screws as alternative measurement points.

Document the largest value.

Insulation Resistance

Insulation resistance >> 2 M

Ω

Measurement with 500 V between shorted mains connectors and potential equalization bolt.

Earth Leakage Current

Earth leakage current

≤ 30 µA incl. mains cable.

Measurement under standard conditions at the protective conductor of the mains cable. Two measurements (one with changed poles).

Document the largest value.

Infusomat P 2.0gb 8 - 1

8 - 2

Procedural Instructions for Inspection

3. Functional Inspection

Fig.: 8 - 1

Switch-on Test

Switch-on test keypad and display: check correct procedure.

Alarm tone, display: rate 000.0, VOL, TIME etc., display of all pixel, contrast, display light, alarm and operating LED.

Battery Test

Switch mains/battery/mains: Interrupt mains supply twice in intervals of 1 second. Pay attention to the switch-over in the display. The unit must not switch to malfunction.

Note

Running time minimum 30 minutes after charging of 16 hours.

Air Sensor

Set rate to 400 ml/h.

Then inject 0.4 ml air bubble (inject piece). An alarm must be activated.

Drop Sensor

Set rate to 400 ml/h.

Simulate occlusion: Clamp infusion line in front of the pump to prevent any drops. Alarm in less than 5 sec.

Simulate free flow: Press the bottom part of the drop chamber together, to generate a jet. Immediate alarm.

Staff Call

Connect MFC test plug

Generate an alarm (e.g. open pump cover during operation), red LED is on in the test plug

If ”dynamic” is set, 1 sec.

If ”static” is set, until the alarm is acknowledged

Alarm Suppression

Press the alarm key. The current alarm is suppressed for 2 minutes.

Infusomat P 2.0gb

4. Pump Unit Inspection

Fig.: 8 - 2

Infusomat P 2.0gb

Procedural Instructions for Inspection

General

Room temperature 20 - 28° C

Use infusion line Intrafix AIR P (PVC) only once.

Connect manometer to the outlet side of the pump and position the manometer approx. to medium height of the Infusomat P.

Vent manometer (filled with water)

φ100 mm or 160 mm.

Measurement range: 4 bar

The results differ according to different measurement procedures.

With electronic measurement devices the values may be approx.

0.1 bar higher than indicated.

Electronic Occlusion Pressure (Occlusion Sensor)

Switch off drop control.

Set 600 ml/h and deliver in an open system for one minute.

Close the system and build-up pressure against a manometer with

100 ml/h.

Occlusion sensor threshold low. . . . . . . . . . . . . 400 to 1000 mbar

Occlusion sensor threshold high . . . . . . . . . . . 1000 to 1600 mbar

Note

The pressure threshold can be changed in the service program (not recommended).

Default setting:

- low pressure: 0.6 bar

- high pressure: 1.2 bar

Tolerance range:

- set value: ± 0.3 bar.

Mechanical Occlusion Pressure

Set occlusion sensor threshold to mechanical (test plug).

Switch off drop control.

Build up pressure with 600 ml/h. Then measurement with 100 ml/h.

Read 90 seconds after start of delivery:

Measurement upper pressure value

Measurement lower pressure value

Measured values

Table 4 - 1 „Compatibility List“

After the measurement inspection the mechanical setting must be switched off! The electronic occlusion pressure is not automatically activated again when the service plug has been disconnected.

8 - 3

8 - 4

Procedural Instructions for Inspection

Mechanical Pressure Setting

Check pump pressure. If the deviation is max. ± 0.3 bar from set range, the pump can be calibrated.

Perform pressure measurement. Calibrate the pressure range at the set screw with an Allen key 2.5 mm. to the upper pressure value of 2.4 bar.

After the measurement inspection the mechanical setting must be switched off! The electronic occlusion pressure is not automatically activated again when the service plug has been disconnected.

Flow Inhibitor

Switch to stop at high pressures. Then open unit door. The pressure must stay above 0.8 bar.

Delivery Accuracy

Temperature 22° C

Rate > 1 ml/h

Typically ± 5% at a measurement of more than 8 hours.

Infusomat P 2.0gb

80 ± 0.4 ml

Fig.: 8 - 3

Procedural Instructions for Inspection

Reference Height

80 ± 2 cm

Determination of Delivery Rate

Alternative procedure (12 minutes short measurement)

Temperature 20 - 28° C

Measurement Equipment:

500 ml glass bottle, vented

Intrafix AIR P (PVC), drop chamber filled 2/3

Graduated cylinder 25 ml, accuracy ± 0.4 ml

Infusion solution NaCl or distilled water .

Procedure:

Use a new infusion line for every measurement.

Check the system for narrow sections or kinks.

Delivery rate 125 ml/h.

The system run-in time is 1 - 2 minutes, but not longer than

2 minutes.

Insert the outlet cannula in the graduated cylinder.

Measurement rate: 125 ml

Measured volume: 25 ml

Simultaneously start stop watch and Infusomat P.

Stop when the 25 ml mark is reached and read time.

As shown in the graph the delivery behaviour slightly changes over the infusion time. Consequently the tolerances must be in the upper range when the delivery accuracy (± 5% over 8 hours) is checked with a short measurement over 12 minutes.

Expected rate deviation due to the short time method:

Software IFPC:+4.5% tolerance range -0.5% bis +9.5% of the set rate.

Software IFPe / IFPE:+2.5% tolerance range -2.5% bis +7.5% of the set rate.

Fig.: 8 - 4 Graph

Infusomat P 2.0gb 8 - 5

8 - 6

Procedural Instructions for Inspection

Measurement Time

11 min

12 min

11 min

10 min

45.9 sec

39.0 sec

32.3 sec

25.7 sec

19.7 sec

12.9 sec

6.7 sec

0.6 sec

37.9 sec

30.0 sec

22.3 sec

14.7 sec

7.3 sec

0.0 sec

52.9 sec

54.5 sec

48.5 sec

42.9 sec

26,1

+10

+11

+12

+15

-2

-1

-5

-4

-3

Deviation

%

135,00

136,25

137,50

138,75

140,00

143,75

125,00

126,25

127,50

128,25

130,00

131,25

132,50

133,75

118,75

Rate ml/h

120,00

121,25

122,50

123,75

Table 8 - 1 Measurement Examples

The inspection and calibration - if required - must be performed with the infusion line Intrafix AIR P (PVC)!

Alternative Measurement Procedure

Inspection of the delivery rate with a weight measurement. Avoid errors due to evaporation!

Measurement Equipment:

Scales

Accuracy 0.1 g . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 min

Delivery Rate Determination:

Set the delivery rate to 125 ml/h.

The run-in time is 1 - 2 minutes.

Insert the outlet cannula in container and simultaneously start stop watch and Infusomat P.

After the time has expired stop Infusomat P and stop watch.

Immediately determine the delivery rate.

Infusomat P 2.0gb

9 - 2

9 -

Test Equipment and Special Tools

Test Equipment and Special Tools For Repair / for Technical Safety Inspection (TSI)

Order No.

Test equipment case Infusomat fm (complete) . . . . . 0770 1527 with:

Template 4 mm (for adjustment after exchange of the pump cover) (for Infusomat fmS) . . . . . . . 0770 1489

Pin punch 1.8 mm x 160 mm (for hinge pin/ disassembly of the pump cover) . . . . . . . . . . . . . . 0770 1446

Pin punch 6 mm x 125 mm (for hinge pin/ assembly of the pump cover). . . . . . . . . . . . . . . . . 0770 1454

Flat tool 100 x 20 mm (for assembly/ disassembly of the tube adapter of the Infusomat fmS) . . . . . . . . . . . . . . . . . . . . . . 0770 1462

Special socket spanner M18 (for disassembly of the recessed plug). . . . . . . . . . . . . . . . . . . . . . . . . . 0770 1497

Manometer 0 - 4 bar . . . . . . . . . . . . . . . . . . . . . . . 0770 1357

Service plug (red) . . . . . . . . . . . . . . . . . . . . . . . . . . . 0770 0709

MFC service plug. . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 1215

OIL test infusion line (for Infusomat fmS) . . . . . . 0770 1500

Template 2.2 mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0770 5034

Calibration device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0770 501A

Screw driver Torx T6

Screw driver Torx T10

Infusomat P 2.0gb 9 - 1

Test Equipment and Special Tools

For your notes:

9 - 2 Infusomat P 2.0gb

10 - 4

10 -

Spare Parts List

Unit Elements

Designation

Mains Fuses

Fuse T 0.16 A for 200 / 230 / 240 V

(10 pcs.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3477 2847

Fuse T 0.315 A for 100 / 110 / 120 V

(10 pcs.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3477 0534

Fuse holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 0979

Pump Cover

Pump cover with lock . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 1916

Blind plug 7.1 mm (10 pcs.) . . . . . . . . . . . . . . . . . . . . . .3477 3207

Torsion spring in lever/pump cover (5 pcs.) . . . . . . . . 3477 3363

Torsion spring for pump cover (5 pcs.) . . . . . . . . . . . . 3477 3355

Lever (pump cover) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3477 4092

Hinge pin for pump cover . . . . . . . . . . . . . . . . . . . . . . . 3477 3967

Hinge pin for pump cover lever . . . . . . . . . . . . . . . . . . 3450 5725

Pump Housing

Ord. No.

Pump housing, (cpl.) . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3390

Designation Ord. No.

Finnish. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3404

Portuguese. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3382

Czech . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3358

Polish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3358

Turkish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3382

Foot stand complete with rubber feet . . . . . . . . . . . . . 3450 5415

Rubber feet (20 pcs.) . . . . . . . . . . . . . . . . . . . . . . . . . . . 3477 3096

Unit handle with O-rings and PT screws . . . . . . . . . . . 3450 3450

Battery

Battery incl. connector plug

1.2 Ah / 7.2 V and holder . . . . . . . . . . . . . . . . . . . . 3450 2556

Door Lock

Door lock complete with push button . . . . . . . . . . . . . .3450 5601

Spring holder for door lock . . . . . . . . . . . . . . . . . . . . . . 3450 5440

Mounting for door lock . . . . . . . . . . . . . . . . . . . . . . . . . 3477 2790

Controller Board

Distance sleeve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3366

Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3447

Loudspeaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 8848

Rear Panel

Rear panel with screws (M3) and seal . . . . . . . . . . . . . 3450 1860

Cover for optical interface . . . . . . . . . . . . . . . . . . . . . . 3477 3164

Strip seal for rear panel . . . . . . . . . . . . . . . . . . . . . . . . . 3477 3142

MFC connector board . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3374

Potential equalization bolt . . . . . . . . . . . . . . . . . . . . . . 3477 0550 fm recessed plug (3 pin) . . . . . . . . . . . . . . . . . . . . . . . . 3477 3177

Screw 30x8 for fm recessed plug (20 pcs.) . . . . . . . . . 3477 3185

U Washer 3.2 (20 pcs.). . . . . . . . . . . . . . . . . . . . . . . . . . 3477 3193

Mains module 200/230/240 V. . . . . . . . . . . . . . . . . . . . 3450 1886

Mains module 100/110/120 V . . . . . . . . . . . . . . . . . . . . 3450 1894

Mains module 230 V . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 190A

Drop sensor socket incl. cable and plug . . . . . . . . . . . . 3450 1878

Housing

Housing Labelling

German . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 1851

French . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 1851

Dutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 1851

Italian . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 1851

English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3382

Spanish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3382

Danish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3404

Norwegian. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3404

Swedish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3404

Front Panel

Front panel without clamp lever and torsion spring . . 3450 2092

Circular seal 571 mm / 45 mm . . . . . . . . . . . . . . . . . . . 3477 3126

Tamper-proof caps 10 mm (50 pcs.) . . . . . . . . . . . . . . 3477 3134

Pump housing, cpl. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3390

Cover Ø 6.4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3412

Clamp lever with torsion spring and pin 4x20 . . . . . . 3450 3420

Torsion spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 3439

Reed sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 1754

Infusomat P 2.0gb 10 - 1

10 - 2

Spare Parts List

Designation Ord. No.

Pump Unit

Note

When replacing the finger pump adhere to

Finger pump (without motor) including pump, . . . . . 3450 1746 pump cover, seal membrane and occlusion sensor

board, software IFPC

(installed up to unit serial no. 5505)

Finger pump (without motor) including pump, . . . . . 3452 0481 pump cover, seal membrane and occlusion sensor

board, software IFPe, IFPE

(installed from unit serial no. 5506)

Finger pump (without motor and board) . . . . . . . . . . 3452 0597 incl. pump, pump cover, and seal membrane

Motor with pinion for finger pump . . . . . . . . . . . . . . . 3450 1924

Operating Unit

Membrane keypad with support plate and seal. . . . . . 3450 1800

LCD module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 1819

Flex cable, preformed . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 8830

Frame incl. pressure spring and magnet . . . . . . . . . . . 3450 1835

Flexible cable 42 mm (5 pcs.) . . . . . . . . . . . . . . . . . . . . 3477 3347

Hinge unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 5571

Hinge pin (3 mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 5580

Magnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 5849

Barcode Label

Barcode label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 9070

(see „Order Form“