102.50 mm
410.00 mm
Hardware Install
Select a proper installation method according to what type of WAN medium your ISP is delivering:
Quick Install Guide
A.Telephone line or FTTH
(fiber to the home)
Cable Modem or ONT
Telephone line or Fiber Ethernet Cable or
B. Ethernet cable
Ethernet Cable
3. Connect the router
to power supply
Ethernet Cable
1. Connect the Ethernet cable to
the WAN port on the router .
2. Connect one of the ports （ 1/2/3/4 ）
on the router to your PC.
Package Contents
Wireless Router
Power Adapter
Quick Install Guide
Warranty
If any of the above items is incorrect, missing, or damaged, please contact your
Tenda reseller for immediate replacement.
Configure Router
Launch any browser, say, IE and a screen as seen in the screenshot below will appear; if not, type
192.168.0.1 in the address bar and press Enter. If the screen still does not appear, follow instructions on
Ap pendix 3 to configure your PC.
File(F) (Edit)E View(V) Add to Favorites(A)
Login
1.Enter the login password.
Default:admin
Password:
OK Cancel
2.Click
OK
Appendix 1: Join a Wireless Network
Windows 7
Click Start -> Control Panel -> Network and
Sharing Center -> Change Adapter
Settings ->right click Wireless Network
Connection ->select Connect/Disconnect .
Wireless Network Connection
Not Connected
Disable
Connect / Disconnect
Status
Diagnose
Bridge Connections
Create Shortcut
Delete
Rename
Properties
Currently connected to:
Network 4
Internet access
Wireless Network Connection
Buffalo-G-XXXX
Connect automatically
Connect
1.Find the wireless network you wish to connect.
2.Click Connect .
Open Network and Sharing Center
Please follow instructions on the right table.
Please select a proper Internet connection type. Contact ISP for assistance if you don't know what type of Internet connection to select.
Internet Connection Type Features Instructions
PPPoE
DHCP
Select PPPoE (Point to Point Protocol over
Ethernet) if you used to connect to the Internet using a broadband connection that requires a username and a password.
Select DHCP (Dynamic IP) if you can access
Internet as soon as your computer directly connects to an Internet-enabled ADSL/Cable modem.
Select
Select
PPPoE
DHCP
, enter the PPPoE username and PPPoE password provided by your ISP, customi ze a security key to secure your wireless network and then click wireless network and then click OK .
OK
, customize a security key to secure your
*For configurations of other Internet connection types, go to our website: www.tendacn.com and download the latest user guide from Support->
Downloads.
.
Note:
1.The default SSID (wireless network name) is Tenda_xxxxxx, where xxxxxx is the last 6 characters in the device's MAC address.
2.By default, for first-time wireless connection to the device, there is no preset security key; however, once you connect to it wirelessly and configure
Internet connection yet make no change in the security key field, 12345678 will be automatically set as the security key by default.
3. To configure the router wirelessly, follow instructions on sections: 1. Hardware Install -> Appendix 1 or Appendix 2 -> 2. Configure Router .
MAC OS
Connect to a Network
Security key:
2.Click OK .
Hide characters
OK Cancel
When you see Connected displayed next to the wireless network you selected, you have connected to the wireless network successfully.
Currently connected to:
Network 4
Internet access
Buffalo-G-XXXX
Internet access
Buffalo-G-XXXX Connected
Click -> System Preferences .
Finder File Edit View
About This Mac
Software Update...
Mac OS X Software...
System Preferences...
Dock
Location
Recent Items
Force Quit Finder
Sleep
Restart...
Shut Down...
Log Out helpdesk...
Personal
Show All
Appearance Desktop &
Screen Saver
Dock
Hardware
Select Network from
Internet & Network .
Saver
Internet & Network
Expose &
Spaces
MobileMe
System
Network Quick Time Sharing
Accounts Date & Time Parental
Controls
Software
Update
Show All
Network
2.Click here to Turn Wi-Fi On
Location: Automatic
Ethernet
1.Click Wi-Fi
FireWire
Not Connected
Wi-Fi
On
Status: On Turn Wi-Fi Off
Wi-Fi is turned on but is not connected to a network.
Network Name No network selected
Buffalo
Buffalo -
G
G
-
-
XXXX
XXXX
3.Click No network selected
4.Select the wireless
network name of your router
Show Wi-Fi status in menu bar
Click the lock to prevent further changes.
Assist me...
Advanced...
Revert Apply
LED Description
Solid: Indicates a proper connection to the power supply
Blinking: System is functioning properly
Off: WPS is disabled
Blinking: Negotiating key
Solid: WPS is enabled
Solid: Wireless is enabled
Blinking: Transferring data
Solid: Indicates proper connection
Blinking: Transmitting data
Button Description
When the router power on, if press this button shortly(Less than 10 seconds),
WPS will be enabled, if press it more than 10 seconds till the SYS light stop blinking, the router will restore to Factor
Default Setting.
Images herein are for references only.
1. You can access Internet via a wired connection to the device when Connection
Status displays Connected .
2. To access Internet via a wireless connection to the device, see Appendix 1
(for Windows 7/MAC OS) or Appendix 2 (for iPhone/iPad/Windows XP).
For a desktop, you will need an external wireless adapter.
The network “catherine” requires a WPA
1.Enter the wireless password.
Password:
Show password
2.Click on Join .
Cancel Join
Quick Install Guide
Appendix 2 : Join a Wireless Network (iPhone/Windows XP) iPhone/iPad
1.Scroll screen to find the
Settings icon.
2.Click the icon.
Settings
1.Click Wi-Fi .
Settings
Airplane Mode OFF
Wi-Fi ON
Wi-Fi Disconnected
Choose a Network…
Bluetooth Off
Buffalo-G-XXXX
Do Not Disturb OFF
Buffalo-G-XXXX
Notifications
Buffalo-G-XXXX
General
Sounds
Picture Frame
Privacy
JOSHUA
3.Find the name of the
wireless network you wish
to connect
4.Click on it.
iCloud
Mail, Contacts, Calendars
Notes
Reminders
Other…
Ask to Join Networks
Known networks will be joined automatically. If no known networks are available, you will be asked before joining a new network.
2.Click here to join the wireless network.
Cancel
Enter the password for “dianshang”
Enter Password Join
Password
1.Enter a security key.
Settings
Airplane Mode
Wi-Fi
OFF
Tenda_xxxxxx
Bluetooth Off
Do Not Disturb
Notifications
OFF
General
Sounds
Brightness & Wallpaper
Picture Frame
Privacy
Wi-Fi
Wi-Fi
Choose a Network…
ChinaNet-YJ3M
Buffalo-G-XXXX
ON dianshang
JOSHUA
Connected successfully iCloud
Mail, Contacts, Calendars
Notes
Reminders
Other…
Ask to Join Networks
Known networks will be joined automatically. If no known networks are available, you will be asked before joining a new network.
Windows XP
Click Start -> Control Panel ->Double click
Network Connections ->right click
Wireless Network Connection ->select
View Available Wireless Networks .
Disable
View Available Wireless Networks
Status
Repair
Bridge Connections
Create Shortcut
Delete
Rename
Properties
Double click the wireless network you wish
Choose a wireless network
Refresh network list
Buffalo-G-XXXX
Set up a wireless network for a home or small office
Security-enabled wireless network(WPA)
To connect to this network,click Connect,You might need to enter additional information
Wireless Network Connection
The network “Tenda_home” requires a network key(also called a WEP key or WPA key),A
1.Enter a security key.
Type the key,and then click Connect
Network Key:
Confirm network key:
2.Click Connect .
Connect Cancel
Local Area Connection 2
Network Tasks
Refresh network list
Set up a wireless network for a home or small office
Choose a wireless network
Connected Successfully.
Click an item in the list below to connect to a wireless network in range or to get more information
Buffalo-G-XXXX Connected
Securit-enabled wireless network(WPA)
Buffalo-G-XXXX
Unsecured wireless network
Related Tasks
Learn about wireless networking
Change the order of preferred networks
Change advanced settings
Appendix 3: Configure PC
Windows 7
Click Start -> Control Panel
-> Network and Sharing
Center -> Change Adapter
Setting ->right click Local
Area Connection
->select Properties.
Local Area Connection
Network 2
Disable
Status
Diagnose
Bridge Connections
Create Shortcut
Delete
Rename
Properties
Local Area Connection Properties
Networking Authentication Sharing
Connect uaing:
Reatek RTL8102E/RTL8103E Family PCI-E Fast Etheme
This connection uses the following tems:
Contigure...
Double click Internet Protocol
Version 4(TCP/IPv4) .
QoS Pocket Scheduler
File and Printer Sharing for Microsoft Networks
Internet Protocol Version 6(TCP/IPv6)
Internet Protocol Version 4(TCP/IPv4)
Link-Layer Topology Discovery Mapper I/0 Driver
Link-Layer Topology Discovery Responder
Inatall...
Uninatall Properties
Description
Transmission Control Protocol/Internet Protocol. The default wide area network protocol that provides communication across diverse interconnected networks.
Internet Protocol Version 4 (TCP/IPv4)Properties
General
Alternate Configuration
1.Select
Obtain an IP address
this capability. Otherwise,you need to ask your network administrator
automatically
Obtain an IP address automatically
Use the following IP address:
IP address:
2.Select Obtain DNS server
Obtain DNS server address automatically
Use the following DNS server addresses:
Preferred DNS server:
Alternate DNS server :
3.Click OK ok
Advanced...
Cancel
FAQs
1. Where should I place the wireless device for optimum performance?
1. Place it in the center to extend wireless coverage as far as possible.
2. Never place the device near to metal objects or in direct sunshine.
3. Keep it far away from devices that use the 2.4 GHz radio wave frequency to transmit and receive data, such as 802.11g/n wireless network devices, electronic devices such as cell phones, radio transmitters, blue tooth, cordless phones, fax machine, refrigerator and microwaves to avoid electronic interference.
2. I cannot access the device's management interface. What should I do?
1. Verif y the physical connection (namely, the Ethernet cable) between your PC and the device. For details, see 1.
Hardware Install hereof.
2. Double check the TCP/IP settings on your PC. For details, see Appendix 3 .
Configure PC hereof.
3. Press the Rese t button for over 10 seconds on the device and then re-access the management interface.
4. Change the Ethernet cable that connects your PC and the device.
5. Try accessing device management interface from other PCs, smart phones or iPads.
6. Connect your PC alone to one of the LAN ports on the device.
3. I forget the wireless security key. What should I do? How do I configure or change the security key?
1. Try the default security key: 12345678.
2. Access the device management interface and reconfigure a security key. For details, see 1. Hardware
Install and 2. Configure Router .
3. Press the Reset button for over 10 seconds on the device to restore factory default settings.
4. My notebook is unable to search wireless networks, what should I do?
1. Verify that wireless is enabled on your notebook by checking the wireless hardware or software button on your notebook. The hardware button is usually located on the side of your notebook. Note that
Local Area Connection Properties
Networking
Sharing
Connect uaing:
Reatek PCle GBE Family Controler
Contigure...
This connection uses the following tems:
Clent for Microaoft Networks
QoS Pocket Scheduler
File and Printer Sharing for Microsoft Networks
Internet Protocol Version 6(TCP/IPv6)
Internet Protocol Version 4(TCP/IPv4)
Link-Layer Topology Discovery Mapper I/0 Driver
Link-Layer Topology Discovery Responder
Inatall...
Uninatall Properties
Description
Allows your computer to access resources on a Mcrosoft network.
Click OK ok Cancel
MAC OS
Click on the Apple icon from the top-left corner and select System Preferences .
Finder File Edit View
About This Mac
Software Update...
Mac OS X Software...
System Preferences...
Dock
Location
Recent Items
Force Quit Finder some notebooks may not have such hardware button. Software button can be implemented by pressing Fn+ . Fn is situated on the bottom left corner of your keyboard. may be any key between F1-F12 depending on what type of keyboard you are using.
2. Log in to the device, select Advanced -> Wire less and change the wireless network name (SSID).
Then search again.
3. Follow below steps to verify that wireless service is enabled on your notebook (for Windows XP OS only).
From the desktop, right-click on the My Computer icon and select Manage. Select Services and
Applications, double click Services and view the status of Wireless Zero Configuration. If Status dose not display Started, right click the Wireless Zero Configuration and select Start; if Startup Type displays Disabled, right click the Wireless Zero Configuration, select Properties; from the Startup Type drop-down list box, select Automatic and then click Start in Service Status.
5. Why cannot I join the searched wireless network?
1. Verify that you entered a correct security key. If not, see question 3.
2. Log in to the device, select Advanced -> Wireless and change the wireless network name ( SSID).
Then connect again.
3. Log in to the device, select Advanced -> Wireless -> Wireless Security and change the security settings. Then connect again.
6. Wireless connection shows "Con nected" but I cannot access Internet. What should I do?
1. Verify that you are connecting to a right SSID (wireless network).
2. Follow instructions on this Quick Install Guide to reconfigure all settings.
Personal
Show All
Appearance Desktop &
Screen Saver
Hardware
Dock Expose &
Spaces
Bluetooth
Click Network
Displays Energy
Saver
MobileMe
System
Network Quick Time Sharing
Accounts Date & Time Parental
Controls
Software
Update
Network
Show All
Location: Automatic
1.Click on Ethernet
Ethernet
Connected
Bluetooth
Not Connected
Status: Connected
Ethernet is currently active and has the IP address 142.104.57.27.
FireWire
Not Connected
Wi-Fi
Off
Configure: Using DHCP
IP Address: 0.0.0.0
2.Choose Using DHCP
Router: 142.104.57.62
DNS Server: 142.104.6.1,142.104.80.2
Search Domains: uvic.ca
802.1X: WPA:UVicDef...
Connect
Click the lock to prevent further changes.
Assist me...
3.Click Apply
Revert Apply
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment genera tes, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separat ion between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The manufacturer is not responsible for any radio or TV interference caused by una uthorized modifications to this equipment.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
NOTE:(1)The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.(2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable
410*287mm
，风琴四折页，折后尺寸
102.5*143
.
5mm
