Chungear Industrial TR171A Ceiling Fan Remote Operation and Installation Instructions

Below you will find brief information for Ceiling Fan Remote TR171A. The Ceiling Fan Remote TR171A is a wireless remote control unit designed to control ceiling fans and lights. It features multiple speed settings for the fan, allowing you to adjust air circulation to your preference. The remote control unit is easy to install and comes with instructions for proper wiring and setup.

PDF

Document

CEILING FAN REMOTE CONTROLLER

OPERATION AND INSTALLATION INSTRUCTIONS

(Please keep this instruction pamphlet.)

IMPORTANT

YOU MUST SET CEILING FAN MANUAL SWITCH TO HIGH SPEED AND LIGHT KIT

(IF ANY) TO ON POSITION BEFORE OPERATING REMOTE CONTROL.

IMPORTANT POINTS TO REMEMBER:

1.Read and save these instructions.

2.Please note that all fixed wiring appliances should be installed by a qualified electrician.

3.The supply to the remote control receiver should be connected through a mains switch, i.e. existing wall switch.

4.Disconnect from power supply at wall switch before working on remote control receiver or ceiling fan.

5.Install receiver into the ceiling fan canopy of the fan to ensure proper protection.

6.This unit is to be used for the control of ceiling fan and in a AC110/120V 60Hz power supply only.

7.Do not install in damp locations or immerse in water. (For indoor use only.)

8.Do not pull on or cut leads shorter.

9.Do not drop or bump the unit.

10.

PLEASE NOTE: The battery will weaken with age and should be replaced before leaking takes place as this will damage the transmitter. Dispose of used battery properly, keep the battery out of reach of children.

11.

CAUTION: To reduce the risk of fire or injury, do not use this product in conjunction with any variable

(rheostat) wall control.

INSTALLATION INSTRUCTIONS

CAUTION: INCORRECT WIRE CONNECTION WOULD DAMAGE THIS RECEIVER.

1.Ceiling fan must be set at HIGH speed and light kit (If any) at ON position by pressing the “Light Switch” after installation.

2.Once the connection has been made, the receiver inserts into the drop rod hanging bracket. The canopy comes up to cover the receiver and bracket.

CODE SWITCH

1.CODE SWITCH: Codes are set by pushing dip switches up or down. It is imperative that the code used for both transmitter and receiver is exactly the same, otherwise remote controller will not work. Please note the code switch will enable you to operate a second remote controller independently. For example, if you have two ceiling fans with 2 remote control units, set 2 different codes for each set of transmitter/receivers. This means you can operate each ceiling fan independently.

2.Your remote control is ready for use after battery installation.

TRANSMITTER

FUNCTIONS OF TRANSMITTER

OFF: Turn off the fan.

（

POWER

）

M odel ： TR171A

HI : Turn on the fan at high speed. （ 4 ）

MED:Turn on the fan at medium speed （ 3 ）

LOW: Turn on the fan at low speed （ 2 ） L.LOW:Turn on the fan at lowest speed （ 1 ）

LIGHT: Press and release immediately to turn on or off the light.

Press and hold to dim or brighten lights to the desired level and release. (Only for the tungsten bulb.).

Ceiling Fan Remote

Control

Wiring Connection

Installation of Transmitter

Wall Mount Holder with two screws.

CAUTION:

To assure continued FCC compliance:

Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment.

FCC ID

： KUJCE10202

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Hello! I am an AI chatbot specifically trained to assist you with the Chungear Industrial TR171A Ceiling Fan Remote Operation and Installation Instructions. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant is out of keyboard. Please, try again later.

Key features

Remote control of ceiling fan
Multiple speed settings
Light control (if equipped)
Easy installation
Compatible with 110/120V 60Hz power supply

Frequently asked questions

First, ensure the ceiling fan is set to high speed and the light kit is on. Then install the receiver in the fan canopy and pair it with the transmitter by setting the code switch. Finally, install the transmitter and insert the battery.

Yes, by setting different codes for each set of transmitter/receiver you can operate multiple fans independently.

This unit is specifically designed for use with ceiling fans in a 110/120V 60Hz power supply. However, always check the compatibility of the remote with your fan’s specifications.