Motorola MC13192SARD Sensor Applications Reference Design User's Guide
Below you will find brief information for Sensor Applications Reference Design MC13192SARD. The MC13192 Sensor Applications Reference Design (SARD) introduces users to the MC13192 2.4 GHz wireless data transceiver. It includes an RS232 port, background debug module for in-circuit hardware debug, switches, LEDs, and a host MCU and allows the user flexibility in establishing wireless data networks.
Advertisement
Advertisement
Sensor Applications Reference
Design (SARD)
User’s Guide
MC13192SARDUG/D
Rev. 1.1, 08/2004
HOW TO REACH US:
USA/EUROPE/LOCATIONS NOT LISTED:
Motorola Literature Distribution;
P.O. Box 5405, Denver, Colorado 80217
1-303-675-2140 or 1-800-441-2447
JAPAN:
Motorola Japan Ltd.; SPS, Technical Information Center,
3-20-1, Minami-Azabu Minato-ku, Tokyo 106-8573 Japan
81-3-3440-3569
ASIA/PACIFIC:
Motorola Semiconductors H.K. Ltd.; Silicon Harbour
Centre, 2 Dai King Street, Tai Po Industrial Estate,
Tai Po, N.T., Hong Kong
852-26668334
TECHNICAL INFORMATION CENTER:
1-800-521-6274
HOME PAGE: http://www.motorola.com/semiconductors
Information in this document is provided solely to enable system and software implementers to use Motorola products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document.
Motorola reserves the right to make changes without further notice to any products herein.
Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in
Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola and the Stylized M Logo are registered in the U.S. Patent and Trademark Office. All other product or service names are the property of their respective owners. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
© Motorola, Inc. 2004
Contents
Chapter 1
Introduction and Configuration
MC13192 Sensor Applications Reference Design (SARD) Components . . . . . . . . . . . 1-2
Programming the SARD (User Defined Software) . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Appendix A
SARD Board Layout and Bill of Materials
MOTOROLA Contents iii
iv Sensor Applications Reference Design (SARD) User’s Guide MOTOROLA
List of Figures
Point to Point MC13192 SARD Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . 1-3
MC13192 SARD Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
DCE-DB9 Female Connector (Looking into the SARD Connector) . . . . . . . . . 1-5
SARD Component Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
MOTOROLA List of Figures v
vi Sensor Applications Reference Design (SARD) User’s Guide MOTOROLA
List of Tables
LED and Switch Port Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
MOTOROLA List of Tables vii
viii Sensor Applications Reference Design (SARD) User’s Guide MOTOROLA
About This Book
This guide provides detailed information about the MC13192 Sensor Applications Reference Design
(SARD). The SARD provides all the components to evaluate and use an MC13192. It is intended to allow a system engineer or software developer to gain an understanding of the MC13192 and its protocol.
Audience
The guide is intended for software and system engineers who are developing their products or software applications making use of the MC13192 to achieve wireless connectivity capability.
It is assumed that the reader has a good working knowledge of general-purpose microcontrollers (MCU).
Organization
The book is divided into 1 chapter and 1 appendix.
Chapter 1 introduces the MC13192 Sensor Applications Reference Design (SARD) functionality and
features.
Appendix A provides figures of the SARD printed circuit board.
Conventions
This section names, describes, and defines the conventions used in the book. This document uses the following conventions:
• OVERBAR is used to indicate a signal that is active when pulled low: for example, RESET.
• Logic level one is a voltage that corresponds to Boolean true (1) state.
• Logic level zero is a voltage that corresponds to Boolean false (0) state.
• To set a bit or bits means to establish logic level one.
• To clear a bit or bits means to establish logic level zero.
• A signal is an electronic construct whose state conveys or changes in state convey information.
• A pin is an external physical connection. The same pin can be used to connect a number of signals.
• Asserted means that a discrete signal is in active logic state.
— Active low signals change from logic level one to logic level zero.
— Active high signals change from logic level zero to logic level one.
• Negated means that an asserted discrete signal changes logic state.
— Active low signals change from logic level zero to logic level one.
— Active high signals change from logic level one to logic level zero.
• LSB means least significant bit or bits, and MSB means most significant bit or bits. References to low and high bytes or words are spelled out.
MOTOROLA About This Book ix
Definitions, Acronyms, and Abbreviations
The following list defines the acronyms and abbreviations used in this document. As this template develops, this list will be generated from the document. As we develop more group resources, these acronyms will be easily defined from a common acronym dictionary. Please note that while the acronyms are in solid caps, terms in the definition should be initial capped ONLY IF they are trademarked names or proper nouns.
ISM
PER
RF
Rx
SPI
Tx
Industrial Scientific Medical packet error rate radio frequency receive serial peripheral interface transmit
References
The following sources were referenced to produce this book:
[1] ESD Style Guide.
[2] IEEE Guide to Software Requirements Specifications, July1984
Document Change History
Release
0.1
0.2
0.3
0.4
0.5
Date
May 21, 2004
May 24, 2004
May 27, 2004
June 18, 2004
June 21, 2004
Change Summary
Initial document creation.
Multiple edits, new lo resolution board picture, new BOM.
Multiple edits.
Updated BOM, PCB layouts, and text edits throughout.
Removed 191 references, changed to UG x Sensor Applications Reference Design (SARD) User’s Guide MOTOROLA
Chapter 1
Introduction and Configuration
This section introduces the MC13192 Sensor Applications Reference Design (SARD) basic components, features, hardware configuration, and applications and programming options.
1.1 Safety Information
Any modifications to this product may violate the rules of the Federal Communications
Commission and make operation of the product unlawful.
47 C.F.R. Sec. 15.21
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
47 C.F.R. Sec.15.105(b)
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The antenna(s) used for this equipment must be installed to provide a separation distance of at least 8 inches (20cm) from all persons.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
MOTOROLA Introduction and Configuration 1-1
Introduction and Configuration
1.2 MC13192 Sensor Applications Reference Design (SARD)
Components
The MC13192 Sensor Applications Reference Design (SARD) introduces users to the MC13192 2.4 GHz wireless data transceiver. It includes an RS232 port, background debug module for in-circuit hardware debug, switches, LEDs, and a host MCU and allows the user flexibility in establishing wireless data networks.
Features of the MC13192 SARD include:
• Provides all hardware required for a complete 2.4 GHz wireless node using IEEE 802.15.4 packet structure.
• One MC13192 2.4 GHz transceiver RF reference design with printed circuit antenna.
• One MC9S08GT60 low-power, low-voltage MCU with 60KB of on-chip Flash.
• Background Debug Module (BDM) programming port for support of Metrowerks CodeWarrior™
Development Studio.
• Provides IEEE 802.15.4 modem.
• Two Accelerometers: MMA6261Q (X and Y axis), MMA1260D (Z axis)
• RS-232 port for interface with a personal computer.
• Four switches and LEDs for control and monitoring.
• Reset switch for program reset.
• Scalable software support:
— Proprietary point-to-point or star networking using Freescale’s Simple Medium Access Control
(SMAC) software
— IEEE 802.15.4 Standard compliant networking using Freescale’s MAC/PHY
— ZigBee™ networking using Freescale’s Z-stack software
1-2 Sensor Applications Reference Design (SARD) User’s Guide MOTOROLA
Hardware Description
1.3 Hardware Description
As previously stated, the MC13192 Sensor Applications Reference Design (SARD) provides the hardware
diagram of two SARDs connected in a simple point-to-point network. Optional personal computers are shown for control and monitoring.
The SARD is a 2 inch x 3 inch module that comprises a complete network node containing the MC13192, crystal, printed circuit antenna and MCU. Also included are jumper-selectable X-Y and Z Axis
Accelerometers, four switches, and four LEDs for monitoring purposes. The SARD derives its power from a 9V battery or a 2.1 mm power connector which allows a supply of 5.5 to 9V.
RS232
PC HCS08
MCU
X-Y Axis Accelerometer
Z Axis Accelerometer
BDM Interface
(Programming
Only)
SPI
MC13192
Node One
RF
Node Two MC13192
SPI
BDM Interface
(Programming
Only)
X-Y Axis Accelerometer
HCS08
MCU
Z Axis Accelerometer
RS232
Figure 1-1. Point to Point MC13192 SARD Block Diagram
PC
1.3.1 MC13192 SARD Circuit Description
Figure 1-2 shows the MC13192 SARD schematic. Appendix A includes board layout, including the
printed dipole receive and transmit antennas, and Bill of Material information. All circuitry required for a
2.4 GHz wireless node is provided. The heart of the design is the MC13192 2.4 GHz transceiver and the
MC9S08GT60 microcontroller. All connections for control of the transceiver by the MCU are provided.
Peripherally, four LEDs and switches interfacing with the MCU are provided for control and demonstration purposes.
Three accelerometers are provided. An MMA6261Q (X and Y axis) and an MMA1260D (Z axis) for demonstration purposes. A Background Debug Module (BDM) port is provided for programming using the CodeWarrior™ Development Studio to develop and in-circuit debug code and program the MCU. An
RS-232 interface is provided to allow monitoring or programming.
MOTOROLA Introduction and Configuration 1-3
Introduction and Configuration
2
2
GND
2,4
GND
2,4 m2 m1
1-4
Figure 1-2. MC13192 SARD Schematic
Sensor Applications Reference Design (SARD) User’s Guide MOTOROLA
Hardware Description
1.3.2 RS232 Connector J102
The RS232 port is J102, a DB9 connector. A standard straight-through DB9 serial cable can be used with a
PC. The port follows the standard RS232 DCE DB9 convention as shown in Figure 1-3. The RS232 is
normally used to connect the SARD to a PC. With an installed bootloader program such as the Sensor
Applications Reference Design (SARD) Embedded Bootloader program, described in document number
MC13192FLUG/D, it can also be used to program the MCU.
Receive Line Signal Detect
Transmitted Data
Received Data
DTE Ready
Signal Ground
1
2
3
4
5
8
9
6
7
DCE Ready
Clear to Send
Request to Send
Ring Indicator
Shield
Figure 1-3. DCE-DB9 Female Connector (Looking into the SARD Connector)
MOTOROLA
Figure 1-4. SARD Component Layout
Introduction and Configuration 1-5
Introduction and Configuration
1.3.3 Power Capability
The SARD can be powered from a 5.5 to 9 V supply connected to J106 or a 9 V battery connected to the
board-mounted battery terminals. See Figure 1-4 for J106 and battery terminal placement. If the
accelerometers are not used, 2.0-3.4V can be supplied on J103. In this configuration, the accelerometer outputs are indeterminate.
1.3.4 LEDs and Switches
D101 through D104 and Switches S101 through S104 are connected to I/O as shown on the SARD
MCU ports are listed in Table 1-1. The on-off switch, S105 is labeled on the board.
Table 1-1. LED and Switch Port Connection
LED/Switch MCU Port I/O
LED 1, D101
LED 2, D102
LED 3, D103
LED 4, D104
RESET, S106
S101
S102
S103
S104
PTD0
PTD1
PTD3
PTD4
RESET
PTA2
PTA3
PTA4
PTA5
Output
Output
Output
Output
-----
Input
Input
Input
Input
1.3.5 Board Reset Function
A hardware reset can be performed on the SARD in two ways:
• The Reset push button.
• The MCU resets the SARD as part of its startup sequence when power is applied and the On/Off switch is turned on.
In both cases, the reset sequence resets the MCU which, in turn, resets the MC13192.
1.3.6 MCU General Purpose Input/Output (GPIO)
Figure 1-4 shows the MCU GPIO that can be interfaced with external hardware such as sensors. When
using the on-board accelerometers, shunts must be installed at PTB0, PTB1, and PTB7, which corresponds to pins 1 and 2, 3 and 4, 11 and 12, of J105, to connect the accelerometer ICs to the MCU. For user defined applications, these shunts can be removed and other hardware attached to the GPIO pins.
1.3.7 BDM Port
Header J101 is a BDM port for use with a P&E BDM-Multilink cable which is available from Metrowerks.
The BDM cable is used with CodeWarrior™ Development Studio for the HCS08 to program the MCU
lead of the BDM cable must align to pin 1 of J101.
1-6 Sensor Applications Reference Design (SARD) User’s Guide MOTOROLA
Applications and Programming Information
When using the parallel port version of the BDM cable, the BDM pod should be powered with a 2 - 5 V negative center contact power supply or the SARD should be powered by a power supply through J106. A
9 V battery is not capable of sourcing the current required by the parallel BDM pod during programming and debug.
1.4 Applications and Programming Information
1.4.1 Accelerometer Application Demo
The SARD comes pre-programmed with the accelerometer demo software. Consult the “Accelerometer
Demonstration Quick Start Guide”, document number AN2762/D for installation and startup instructions.
The receiver is connected to a PC COM port via an RS232 cable. The 9 V battery needs to be installed on the battery terminals or a power supply must be connected to J106 and the on/off switch turned on. Start the accelerometer GUI software, available from our website, and choose the COM port you are using in the dialog box. Install the 9 V battery on the transmitter and turn it on. On the PC screen you can select various ways to display the accelerometer data. One popular way is the cursor mode where you can watch the cursor position move as the transmitter is moved.
1.4.2 Programming the SARD (User Defined Software)
A BDM programmer is used to load the MCU flash memory. Alternatively, the Embedded Bootloader software, described in the, Embedded Bootloader User’s Guide, document number MC13192FLUG/D, can be installed and the SARD can be programmed through the RS-232 port.
MOTOROLA Introduction and Configuration 1-7
Introduction and Configuration
1-8 Sensor Applications Reference Design (SARD) User’s Guide MOTOROLA
Appendix A
SARD Board Layout and Bill of Materials
Figure A-1 shows the SARD printed circuit board layout.
MOTOROLA
Figure A-1. PCB Layout (Top View)
SARD Board Layout and Bill of Materials A-1
SARD Board Layout and Bill of Materials
Figure A-2. PCB Layout (Bottom View)
PTB0
PTB1
PTB2
PTB3
PTB6
PTB7
PTA6
PTA7
PTC0
PTC1
PTC5
PTC6
PTG1
A-2 Sensor Applications Reference Design (SARD) User’s Guide MOTOROLA
PLOVPP
´PP
´PP
´PP
Figure A-3. Printed Circuit Board Antenna Dimensions
PLOVPP
MOTOROLA SARD Board Layout and Bill of Materials A-3
SARD Board Layout and Bill of Materials
Item Qty Part Number
1
2
Table A-1. Bill of Materials (BOM)
Value
1 96000310104 (Label)
26x13 mm
Test
Bar Code
11 50620710001 100 nf
Rating Tolerance
-
Mfg.
Mfg.
Part Number
Reference
ID
Digianswer 96000310100 BarCode1
01
16V 10% X7R Murata
3
4
5
6
7
8
9
10
11
12
13
14
3
2
2
0
3
2
1
4
1
1
1
1
50610422001 220 pf
50210310000 10 pf
50630810001 1.0 µf
50630810001 1.0 µf
50630847001 4.7 µf
50210318000 18 pf
50210215000 1.5 pf
41100017001 Green LED
50V
50V
10V
10V
6.3V
50V
50V
10% X7R
5% NPO
± 10%
X7R
± 10%
X7R
± 10%
X5R
± 5% NPO
± 0.25pf
NPO
ROHM
Murata
Murata
Murata
Murata
Philips
Murata
Citizen
35501319200 MC13192 Motorola
33100000801 MC9SO8GT
60
Motorola
31100331800 MAX3318E MAXIM
35300626000 MMA6261Q
-40 to
+85 °C
-20 to
+85 °C
Motorola
GRM188R71
C104KA01D
MCH155C221
KK
GRP1555C1H
100JD01E
GRM21BR71
A105KA01L
GRM21BR71
A105KA01L
GRM21BR60
J475KA11K
2222 869
15189
GRP1555C1H
1R5CZ01E
CL 170G CD
T
C104,
C107,
C108
C105,
C106
C113,
C117
C123 (not mounted)
C114,
C115,
C116
C101,
C102,
C103,
C109,
C110,
C111,
C112,
C119,
C120,
C124,
C129
C126,
C127
C128
D101,
D102,
D103,
D104
IC101
IC102
MC13192
MC9S08GT60
CFB
MAX3318EE
UP
MMA6261QR
2
IC103
IC104
A-4 Sensor Applications Reference Design (SARD) User’s Guide MOTOROLA
Item Qty Part Number
15
16
17
18
19
20
21
22
23
Table A-1. Bill of Materials (BOM)
Value Rating Tolerance Mfg.
Motorola
Mfg.
Part Number
Reference
ID
MMA1260D IC106 1 35300126000 MMA1260D -40 to
+105
°C
1
1
1
1
1
1
34000295000 LP2950CDT
-3.0
34000295001 LP2950CDT
-5.0
20030400600 2x3 pin
20010500905 9 pin female angle
20030400600 2 pin
20030402600 2x13 pin
National
National
AMP
AMP
LP2950CDT
3.0
LP2950CDT
5.0
826632-3
747844-5
AMP
Samtec
Digi-Key
Keystone
0-826629-2
MTSW-113-0
7-G-D-240
CP-102A-ND
Cat. No. 593
IC108
IC109
J101
J102
J103
J105
J106
J107
24
25
1
1
1
1
20110500204 DC
20110500100 9V Holder and Connector -
Male
20110500101 9V Holder and Connector -
Female
71000536020 DIG536-2
Keystone Cat. No. 594 J108
26
27
28
29
30
31
4 61100422000 220 R
0 61100422000 220 R
1 62100747000 479 K
1 61100310000 10 R
3 61100510000 1.0 K
0 61100510000 1.0 K
62.5m
W/25V
62.5m
W/25V
62.5m
W/25V
62.5m
W/25V
62.5m
W/25V
62.5m
W/25V
5%
5%
1%
5%
5%
5%
Digianswer
YAGEO
DIG536-2
FR4 0.76 mm
RCO2221JR
PCB101
R101,
R102,
R103,
R104
R106 YAGEO
ROHM
YAGEO
RCO2221JR
(not mounted)
MCR01MZSF
4703
RC02100JR
R105
R107
YAGEO RC02102JR
YAGEO RC02102JR
(Not mounted)
R108,
R109,
R112
R114,
R116
MOTOROLA SARD Board Layout and Bill of Materials A-5
SARD Board Layout and Bill of Materials
Table A-1. Bill of Materials (BOM)
Item
32
33
Qty
1
Part Number
61100510000
Value
1.5 K
5 24000600100 Switch
SPST SMD
Rating Tolerance
62.5m
W/25V
5%
Mfg.
YAGEO
ALPS
Mfg.
Part Number
Reference
ID
RC02152JR R113
SKHUAD
34
35
1
1
23010400102
58130916004
Switch
16.000 MHz 20 ppm
20 ppm
ALPS
KDS
SSSS210800
DSX321G
S101,
S102,
S103,
S104,
S106
S105 x101
A-6 Sensor Applications Reference Design (SARD) User’s Guide MOTOROLA
Download
Advertisement
Key features
Evaluates and utilizes the MC13192 wireless connectivity device
Provides insights into the MC13192's functionalities and protocols
Supports software and system engineers in product and application development
Offers a comprehensive platform for exploration and implementation
Frequently asked questions
Software and system engineers developing products or applications using the MC13192 for wireless connectivity.
Provides a comprehensive platform for evaluating and utilizing the MC13192, supports the development of products and applications, and offers a better understanding of the MC13192's capabilities.
Evaluates and utilizes the MC13192, provides insights into its functionalities and protocols, supports software and system engineers, and offers a comprehensive platform for exploration and implementation.