The Federal Communication Commission Statement
This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of more of the following measures: -
-
-
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is -
connected.
- Consult the dealer or an experienced Radio/TV technician for help.
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that change or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS:
1
2
This device may not cause harmful interference and
This device must accept any interference received, including interference that may cause undesired operation.
The antenna used for this transmitter must not be collocated or operation in conjunction with any other antenna or transmitter.
Notice : The changes or modifications not expressly approved by the party responsible
for compliance could void the user ’ s authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user ’ s authority to operate the device.
GOLiFE Care Smart Band
Press the Smart Band button to start use.
appuyez sur la touche Band intelligent de commencer à utiliser.
Bande à puce GOLiFE Care 5
Attention when first time use
Please connect the USB cable to charge, and press the Smart Band button to start use.
Attention lors de la première utilisation du temps
S’il vous plaît connecter le câble USB pour recharger, et appuyez sur la touche
Band intelligent de commencer à utiliser.
GOLiFE Care Smart Band
Button
Display screen
GOLiFE Care Smart Band Clasp USB Cord Correctly line up the band with the charger contact,
And close the lid to begin charging.
Charging Method
GOLiFE Care Wearing and charging
How to Wear
7
U-shape display screen facing up
Correctly line up the band with the charger contact,
And close the lid to begin charging.
Upon wearing, check the direction displayed by the band screen, U-shape display screen facing up.
GOLiFE Care Smart Band
Inbox contain: M/L wristband, adjustable detent pin and detent pin.
M adjustable detent pin detent pin
L
Adjust wristband and accordance with the comfortable of wearing to replace the wristband.
Replace the strap
GOLiFE Care Wearing and charging 9
1
2
1
2
When replacing, please pull out the adjustable detent pin. Removing the strap.
3 3
4 4
Placing the other strap to a fixed position.
After inserting the detent pin and complete the replacement.
GOLiFE Care Smart Band
Downloading and installing GOLiFE Fit APP: Download and install the APP using the two methods below
Scan the QR code or search for in or
GOLiFE Fit App Store Google play
Setting up GOLiFE Care smart band
Launch the APP and register a GOLiFE account (account users can log in directly) .
Launch the APP and select “My Device”. Follow the steps as instructed to connect with GOLiFE Care.
Before pairing via Bluetooth, make sure Bluetooth connection on the mobile device is turned on.
(Go to “Settings” → “Bluetooth” → “Open” on the mobile device.)
Install and setup the GOLiFE Fit APP 11
Downloading and installing GOLiFE Fit APP: Download and install the APP using the two methods below Connect to GOLiFE Care
Scan the QR code or search for in or
Launch the APP and register a GOLiFE account (account users can log in directly) .
Launch the APP and select “My Device”. Follow the steps as instructed to connect with GOLiFE Care.
Before pairing via Bluetooth, make sure Bluetooth connection on the mobile device is turned on.
(Go to “Settings” → “Bluetooth” → “Open” on the mobile device.)
Place the band near the mobile device, and select
“Connect to GOLiFE Care” .
Wait for a pairing code to be generated.
Enter the pairing code to the APP to complete the pairing.
GOLiFE Care Smart Band
Activity Mode
Time/Date Number of steps Distance Calories Amount of electricity
Short press to switch to a different data display.
Long press to switch to the “Activity/Sleep” mode.
(To correctly record data, switch to the corresponding mode on the band before sleeping or after waking up)
Use GOLiFE Care 13
Daily Life Sleep Mode
Short press to switch to a different data display.
Long press to switch to the “Activity/Sleep” mode.
(To correctly record data, switch to the corresponding mode on the band before sleeping or after waking up)
Sleep Time/Date Amount of electricity
Set up an alarm and incoming call through the APP.
Launch the APP regularly to sync data to the cellphone.
Alarm clock
Incoming call
Connect/
Disconnect the device
Bande à puce GOLiFE Care
Les boutons
L’écran
Bande à puce GOLiFE Care Le fermoir Le câble USB
Le procédé de charge
Le port et la charge GOLiFE Care 15
Comment porter la bande
L’écran en forme de
U face dessus
Aligner correctement la bande avec l’endroit où le chargeur pourra la détecter et fermer le couvercle pour commencer la charge
Lors de la mise en place, vérifier la direction affichée à l’écran de la bande
La forme en U devrait pointer vers le haut
Bande à puce GOLiFE Care
Contenu de la boîte : bracelet M/L, goupille d’arrêt ajustable et goupille d’arrêt.
M goupille d’arrêt ajustable goupille d’arrêt
L
Ajuster le bracelet de façon à ce que son port soit confortable pour remplacer la sangle.
Remplacer la sangle
Le port et la charge GOLiFE Care 17
1
2
1
2
3 3
4 4
Lors du remplacement, extraire la goupille d’arrêt ajustable. Remplacer la sangle.
Positionner l’autre sangle à une position fixe.
Après avoir réinséré la goupille d’arrêt, le remplacement est complété.
Bande à puce GOLiFE Care
Téléchargement et installation de l’application GOLiFE Fit:
Télécharger et installer l’application en utilisant l’une des deux méthodes ci-dessous
Scanner le code QR ou rechercher dans l’ ou
GOLiFE Fit App Store Google play
Installer et configurer l’application GOLiFE Fit
Lancer l’application et créer un compte GOLiFE
(les utilisateurs de comptes peuvent se connecter directement) .
Lancer l’application et choisir « My Device ». Suivre les étapes tel qu’indiqué pour se connecter avec
GOLiFE Care.
Avant le pairage via Bluetooth, s’assurer que la connexion Bluetooth de l’appareil portatif est activée.
(Appuyer sur « Settings » → « Bluetooth » → « Open » via l’appareil portatif.)
Téléchargement et installation de l’application GOLiFE Fit:
Télécharger et installer l’application en utilisant l’une des deux méthodes ci-dessous
Scanner le code QR ou rechercher dans l’ ou
Lancer l’application et créer un compte GOLiFE
(les utilisateurs de comptes peuvent se connecter directement) .
Lancer l’application et choisir « My Device ». Suivre les étapes tel qu’indiqué pour se connecter avec
GOLiFE Care.
Avant le pairage via Bluetooth, s’assurer que la connexion Bluetooth de l’appareil portatif est activée.
(Appuyer sur « Settings » → « Bluetooth » → « Open » via l’appareil portatif.)
Configuration de la bande à puce GOLiFE Care 19
Se connecter à GOLiFE Care
Placer la bande près de l’appareil portatif et choisir « Connect to GOLiFE Care »
Attendre qu’un code de pairage soit généré
Entrer le code de pairage à l’application pour compléter le pairage
Bande à puce GOLiFE Care
Mode Activité
Heure/Date Nombre de pas Distance Calories Quantité d’électricité
Appuyer brièvement pour afficher un autre type de données.
Appuyer longuement pour basculer entre les modes « Activité/Sommeil » .
(Pour que les données s’enregistrent correctement, passer au mode correspondant sur la bande avant de dormir ou après s’être réveillé)
Utiliser GOLiFE Care 21
Vie quotidienne Mode Sommeil
Appuyer brièvement pour afficher un autre type de données.
Appuyer longuement pour basculer entre les modes « Activité/Sommeil » .
(Pour que les données s’enregistrent correctement, passer au mode correspondant sur la bande avant de dormir ou après s’être réveillé)
Sommeil Heure/Date Quantité d’électricité Réveillematin
Appel entrant
Connecter/
Déconnecter l’appareil
Configurer le réveille-matin et les appels entrants via l’application.
Lancer régulièrement l’application pour synchroniser les données avec le téléphone cellulaire.
FCC Notices
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Change or modification not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
us.papagoinc.com
