Guangzhou Shirui Electronics 2AFG6-RK3399 AndroidModule User Manual

正基 科技股份有限公司

SPECIFICATION

REV ： 1.1

SPEC. NO.

：

DATE

： 04. 26. 2015

PRODUCT NAME

： AP6255

NAME

APPROVED CHECKED PREPARED DCC ISSUE

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

AMPAK

AP6255

WiFi 11ac + Bluetooth 4.1

Module Spec Sheet

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

1

AP6255 Datasheet

Revision History

Date Revision Content

2015/04/09 - Preliminary

2015/04/26 - Add GPIO pin definiion

Revised By Version

Gary 1.0

Gary 1.1

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

2

AP6255 Datasheet

Contents

Contents ................................................................................................................... 3

1.

Introduction ......................................................................................................... 4

2.

Features............................................................................................................... 5

3.

Deliverables ........................................................................................................ 6

3.1 Deliverables .................................................................................................... 6

3.2 Regulatory certifications ................................................................................. 6

4.

General Specification ......................................................................................... 7

4.1 General Specification ...................................................................................... 7

4.2 Voltages .......................................................................................................... 7

4.2.1 Absolute Maximum Ratings .................................................................... 7

4.2.2 Recommended Operating Rating ........................................................... 7

The module requires two power supplies: VBAT and VDDIO. ......................... 7

5.

Wi-Fi RF Specification ........................................................................................ 8

5.1 2.4GHz RF Specification................................................................................. 8

5.1 5GHz RF Specification.................................................................................. 10

6.

Bluetooth Specification .................................................................................... 13

6.1 Bluetooth Specification ................................................................................. 13

7.

Pin Assignments ............................................................................................... 14

7.1 Pin Outline .................................................................................................... 14

7.2 Pin Definition ................................................................................................ 14

8.

Dimensions ....................................................................................................... 16

8.1 Physical Dimensions .................................................................................... 16

8.2 Layout Recommendation .............................................................................. 17

9.

External clock reference .................................................................................. 18

10.1 SDIO Pin Description .................................................................................. 19

10.

Host Interface Timing Diagram ........................................................................ 20

10.1 Power-up Sequence Timing Diagram ......................................................... 20

10.2 SDIO Default Mode Timing Diagram........................................................... 22

10.3 SDIO High Speed Mode Timing Diagram ................................................... 23

10.4 SDIO Bus Timing Specifications in SDR Modes ......................................... 24

10.5 SDIO Bus Timing Specifications in DDR50 Mode ....................................... 26

11.

Recommended Reflow Profile ......................................................................... 28

Solder Paste definition .......................................................................................... 29

12. Package Information ........................................................................................ 30

12.1 Label ........................................................................................................... 30

Label C Inner box label . .................................................................................... 30

Label D Carton box label . ................................................................................. 30

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

3

AP6255 Datasheet

12.2 Dimension ................................................................................................... 31

12.3 MSL Level / Storage Condition ................................................................... 33

1. Introduction

AMPAK Technology would like to announce a low-cost and low-power consumption module which has all of the Wi-Fi, Bluetooth functionalities. The highly integrated module makes the possibilities of web browsing, VoIP, Bluetooth headsets applications. With seamless roaming capabilities and advanced security, also could interact with different vendors’

802.11a/b/g/n/ac Access Points in the wireless LAN.

The wireless module complies with IEEE 802.11 a/b/g/n/ac standard and it can achieve up to a speed of 433.3Mbps with single stream in 802.11ac draft to connect to the wireless LAN.

The integrated module provides SDIO interface for Wi-Fi , UART / PCM interface for

Bluetooth.

This compact module is a total solution for a combination of Wi-Fi + BT technologies. The module is specifically developed for Smart phones and Portable devices.

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

4

AP6255 Datasheet

2. Features

IEEE 802.11a/b/g/n/ac dual-band radio with virtual-simultaneous dual-band operation

Single-stream spatial multiplexing up to 433.3 Mbps data rate.

Supports 20, 40, 80 MHz channels with optional SGI(256 QAM modulation)

Bluetooth V4.0+EDR with integrated Class 1 PA and Low Energy (BLE) support

Concurrent Bluetooth, and WLAN operation

Simultaneous BT/WLAN receive with single antenna

Supports standard SDIO v3.0 and backward compatible with SDIO v2.0 host interfaces.

- SDIO v3.0(4-bit) — up to 208 MHz clock rate in SDR104 mode

BT host digital interface:

- UART (up to 4 Mbps)

IEEE Co-existence technologies are integrated die solution

ECI — enhanced coexistence support, ability to coordinate BT SCO transmissions around WLAN receives

A simplified block diagram of the module is depicted in the figure below.

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

5

AP6255 Datasheet

3. Deliverables

3.1 Deliverables

The following products and software will be part of the product.

Module with packaging

Evaluation Kits

Software utility for integration, performance test.

Product Datasheet.

Agency certified pre-tested report with the adapter board.

3.2 Regulatory certifications

The product delivery is a pre-tested module, without the module level certification. For module approval, the platform’s antennas are required for the certification.

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

6

AP6255 Datasheet

4. General Specification

4.1 General Specification

Model Name AP6255

Product Description Support Wi-Fi/Bluetooth functionalities

Dimension

WiFi Interface

BT Interface

L x W x H: 12 x 12 x 1.5 (typical) mm

SDIO v2.0/v3.0

UART / PCM

Operating temperature -30°C to 85°C

Storage temperature -40°C to 85°C

Humidity Operating Humidity 10% to 95% Non-Condensing

Storage Humidity 5% to 95% Non-Condensing

4.2 Voltages

4.2.1 Absolute Maximum Ratings

Symbol Description

VBAT

VDDIO

Input supply Voltage

Digital/Bluetooth/SDIO/ I/O Voltage

4.2.2 Recommended Operating Rating

The module requires two power supplies: VBAT and VDDIO.

Operating Temperature

VBAT

VDDIO

Min.

-30

3.13

1.71

Typ.

25

3.6

1.8

Min.

Max.

Unit

-0.5

6 V

-0.5

3.9 V

Max. Unit

85 deg.C

4.8 V

3.63 V

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

7

5. Wi-Fi RF Specification

AP6255 Datasheet

5.1 2.4GHz RF Specification

Conditions : VBAT=3.6V ; VDDIO=3.3V ; Temp:25°C

Feature

WLAN Standard

Description

IEEE 802.11b/g/n/ac, WiFi compliant

Frequency Range 2.400 GHz ~ 2.497 GHz (2.4 GHz ISM Band)

Number of Channels 2.4GHz

： Ch1 ~ Ch14

Modulation

802.11b : DQPSK, DBPSK, CCK

802.11g/n : 64-QAM,16-QAM, QPSK, BPSK

802.11ac : 256-QAM, 64-QAM,16-QAM, QPSK, BPSK

Output Power

Receive Sensitivity

(11b) @8% PER

802.11b /CCK : 16 dBm ± 1.5 dB @ EVM ≤ -9dB

802.11g /64-QAM(R=3/4) : 15 dBm ± 1.5 dB @ EVM ≤ -25dB

802.11n /64-QAM(R=5/6) : 14 dBm ± 1.5 dB @ EVM ≤ -28dB

- 1Mbps PER @ -96 dBm, typical

- 2Mbps PER @ -90 dBm, typical

- 5.5Mbps PER @ -88 dBm, typical

- 11Mbps PER @ -87 dBm, typical

- 6Mbps PER @ -90 dBm, typical

- 9Mbps PER @ -88 dBm, typical

- 12Mbps PER @ -87 dBm, typical

Receive Sensitivity

(11g) @10% PER

Receive Sensitivity

(11n,20MHz)

@10% PER

Receive Sensitivity

(11n,40MHz)

- 18Mbps PER @ -85 dBm, typical

- 24Mbps PER @ -83 dBm, typical

- 36Mbps PER @ -80 dBm, typical

- 48Mbps PER @ -76 dBm, typical

- 54Mbps PER @ -74 dBm, typical

- MCS=0 PER @ -89 dBm, typical

- MCS=1 PER @ -85 dBm, typical

- MCS=2 PER @ -84 dBm, typical

- MCS=3 PER @ -80 dBm, typical

- MCS=4 PER @ -77 dBm, typical

- MCS=5 PER @ -75 dBm, typical

- MCS=6 PER @ -72 dBm, typical

- MCS=7 PER @ -71 dBm, typical

- MCS=0 PER @ -89 dBm, typical

- MCS=1 PER @ -85 dBm, typical

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

8

AP6255 Datasheet

@10% PER

Receive Sensitivity

(11ac,20MHz)

@10% PER

Receive Sensitivity

(11ac,40MHz)

@10% PER

- MCS=2 PER @ -84 dBm, typical

- MCS=3 PER @ -80 dBm, typical

- MCS=4 PER @ -76 dBm, typical

- MCS=5 PER @ -72 dBm, typical

- MCS=6 PER @ -70 dBm, typical

- MCS=7 PER @ -69 dBm, typical

- MCS=0 PER @ -90 dBm, typical

- MCS=1 PER @ -87 dBm, typical

- MCS=2 PER @ -86 dBm, typical

- MCS=3 PER @ -82 dBm, typical

- MCS=4 PER @ -79 dBm, typical

- MCS=5 PER @ -75 dBm, typical

- MCS=6 PER @ -73 dBm, typical

- MCS=7 PER @ -72 dBm, typical

- MCS=8 PER @ -67 dBm, typical

- MCS=0 PER @ -88 dBm, typical

- MCS=1 PER @ -85 dBm, typical

- MCS=2 PER @ -83 dBm, typical

- MCS=3 PER @ -80 dBm, typical

- MCS=4 PER @ -77 dBm, typical

- MCS=5 PER @ -72 dBm, typical

- MCS=6 PER @ -71 dBm, typical

- MCS=7 PER @ -69 dBm, typical

- MCS=8 PER @ -65 dBm, typical

- MCS=9 PER @ -64 dBm, typical

Maximum Input Level

802.11b : -10dBm

802.11g/n : -20dBm

802.11ac : -30dBm

Antenna Reference Small antennas with 0~2 dBi peak gain

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

9

AP6255 Datasheet

5.1 5GHz RF Specification

Conditions : VBAT=3.6V ; VDDIO=3.3V ; Temp:25°C

Feature

WLAN Standard

Output Power

Description

IEEE 802.11a/b/g/n/ac, Wi-Fi compliant

Frequency Range 4.900 GHz ~ 5.845 GHz (5.0 GHz ISM Band)

Number of Channels 5.0GHz

： Please see the table

1

Modulation

802.11a/n : 64-QAM,16-QAM, QPSK, BPSK

802.11ac : 256-QAM, 64-QAM,16-QAM, QPSK, BPSK

802.11a /64-QAM(R=3/4) : 14 dBm ± 1.5 dB @ EVM ≤ -25dB

802.11n /64-QAM(R=5/6) : 13 dBm ± 1.5 dB @ EVM ≤ -28dB

802.11ac/256-QAM(R=3/4) : 12 dBm ± 1.5 dB @ EVM ≤ -30dB

802.11ac/256-QAM(R=5/6) : 10 dBm ± 1.5 dB @ EVM ≤ -32dB

- 6Mbps PER @ -91 dBm, typical

- 9Mbps PER @ -89 dBm, typical

Receive Sensitivity

(11a, 20MHz) @10%

PER

- 12Mbps PER @ -88 dBm, typical

- 18Mbps PER @ -86 dBm, typical

- 24Mbps PER @ -82 dBm, typical

- 36Mbps PER @ -79 dBm, typical

- 48Mbps PER @ -74 dBm, typical

- 54Mbps PER @ -73 dBm, typical

- MCS=0 PER @ -90 dBm, typical

- MCS=1 PER @ -88 dBm, typical

Receive Sensitivity

(11n,20MHz)

@10% PER

Receive Sensitivity

(11n,40MHz)

@10% PER

- MCS=2 PER @ -85 dBm, typical

- MCS=3 PER @ -82 dBm, typical

- MCS=4 PER @ -78 dBm, typical

- MCS=5 PER @ -74 dBm, typical

- MCS=6 PER @ -72 dBm, typical

- MCS=7 PER @ -71 dBm, typical

- MCS=0 PER @ -88 dBm, typical

- MCS=1 PER @ -85 dBm, typical

- MCS=2 PER @ -83 dBm, typical

- MCS=3 PER @ -79 dBm, typical

- MCS=4 PER @ -76 dBm, typical

- MCS=5 PER @ -71 dBm, typical

- MCS=6 PER @ -70 dBm, typical

- MCS=7 PER @ -68 dBm, typical

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

10

AP6255 Datasheet

Receive Sensitivity

(11ac,20MHz)

@10% PER

Receive Sensitivity

(11ac,40MHz)

@10% PER

- MCS=0 PER @ -89 dBm, typical

- MCS=1 PER @ -87 dBm, typical

- MCS=2 PER @ -84 dBm, typical

- MCS=3 PER @ -81 dBm, typical

- MCS=4 PER @ -77 dBm, typical

- MCS=5 PER @ -73 dBm, typical

- MCS=6 PER @ -71 dBm, typical

- MCS=7 PER @ -70 dBm, typical

- MCS=8 PER @ -66 dBm, typical

- MCS=0 PER @ -87 dBm, typical

- MCS=1 PER @ -83 dBm, typical

- MCS=2 PER @ -81 dBm, typical

- MCS=3 PER @ -78 dBm, typical

- MCS=4 PER @ -75 dBm, typical

- MCS=5 PER @ -70 dBm, typical

- MCS=6 PER @ -68 dBm, typical

- MCS=7 PER @ -66 dBm, typical

- MCS=8 PER @ -64 dBm, typical

- MCS=9 PER @ -63 dBm, typical

- MCS=0 PER @ -83 dBm, typical

- MCS=1 PER @ -80 dBm, typical

- MCS=2 PER @ -78 dBm, typical

Receive Sensitivity

(11ac,80MHz)

@10% PER

- MCS=3 PER @ -74 dBm, typical

- MCS=4 PER @ -71 dBm, typical

- MCS=5 PER @ -69 dBm, typical

- MCS=6 PER @ -65 dBm, typical

- MCS=7 PER @ -63 dBm, typical

- MCS=8 PER @ -60 dBm, typical

Maximum Input Level

- MCS=9 PER @ -59 dBm, typical

802.11a/n : -20dBm

802.11ac : -30dBm

Antenna Reference Small antennas with 0~2 dBi peak gain

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

11

AP6255 Datasheet

1

5GHz Channel table

Band (GHz)

5.15GHz~5.25GHz

5.25GHz~5.35GHz

5.5GHz~5.7GHz

5.725GHz~5.825GHz

Operating Channel

Numbers

36

40

44

48

52

56

60

64

100

104

108

112

116

120

124

128

132

136

140

149

153

157

161

165

Channel center frequencies(MHz)

5520

5540

5560

5580

5600

5620

5640

5660

5680

5700

5745

5765

5785

5805

5825

5180

5200

5220

5240

5260

5280

5300

5320

5500

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

12

AP6255 Datasheet

6. Bluetooth Specification

6.1 Bluetooth Specification

Conditions : VBAT=3.6V ; VDDIO=3.3V ; Temp:25°C

Feature Description

General Specification

Bluetooth Standard

Host Interface

Antenna Reference

Frequency Band

Number of Channels

Modulation

RF Specification

Output Power (Class 1.5)

Output Power (Class 2)

Sensitivity @ BER=0.1% for GFSK (1Mbps)

Sensitivity @ BER=0.01% for π /4-DQPSK (2Mbps)

Sensitivity @ BER=0.01% for 8DPSK (3Mbps)

Bluetooth V4.0 of 1, 2 and 3 Mbps.

UART

Small antennas with 0~2 dBi peak gain

2402 MHz ~ 2480 MHz

79 channels

FHSS, GFSK, DPSK, DQPSK

Min. Typical.

9 dBm

2 dBm

-86 dBm

-86 dBm

-80 dBm

Max.

Maximum Input Level

GFSK (1Mbps) :-20dBm

π /4-DQPSK (2Mbps) :-20dBm

8DPSK (3Mbps) :-20dBm

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

13

7. Pin Assignments

7.1 Pin Outline

< TOP VIEW >

AP6255 Datasheet

7.2 Pin Definition

NO

1

2

3

4

Name

GND

WL_BT_ANT

GND

5

6

NC

NC

BT_WAKE

7 BT_HOST_WAKE

8 NC

9

10

11

12

VBAT

XTAL_IN

XTAL_OUT

WL_REG_ON

13 WL_HOST_WAKE

Type

－

I/O

－

－

－

Description

Ground connections

RF I/O port

Ground connections

Floating (Don’t connected to ground)

Floating (Don’t connected to ground)

HOST wake-up Bluetooth device I

O

－

P

I

O

Bluetooth device to wake-up HOST

Floating (Don’t connected to ground)

Main power voltage source input

Crystal input

Crystal output

I Power up/down internal regulators used by WiFi section

O WLAN to wake-up HOST

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

14

AP6255 Datasheet

41

42

43

44

37

38

39

40

29

30

31

32

33

34

35

36

21

22

23

24

25

26

27

28

14 SDIO_DATA_2 I/O

15 SDIO_DATA_3 I/O

16 SDIO_DATA_CMD I/O

17 SDIO_DATA_CLK I/O

18 SDIO_DATA_0 I/O

19

20

SDIO_DATA_1

GND

I/O

－

45

46

47

VIN_LDO_OUT

VDDIO

VIN_LDO

LPO

PCM_OUT

PCM_CLK

PCM_IN

PCM_SYNC

SDIO_VSEL

NC

GND

NC

GND

BT_REG_ON

NC

GND

GPIO_6

GPIO_3

GPIO_5

GPIO_2

UART_RTS_N

UART_TXD

UART_RXD

UART_CTS_N

TP1(NC)

TP2(NC)

TP3(NC)

SDIO data line 2

SDIO data line 3

SDIO command line

SDIO clock line

P

P

P

I

O

I/O

SDIO data line 0

SDIO data line 1

Ground connections

Internal Buck voltage generation pin

I/O Voltage supply input

Internal Buck voltage generation pin

External Low Power Clock input (32.768KHz)

PCM Data output

PCM clock

I

I/O

I/O

－

－

PCM data input

PCM sync signal

SDIO mode selection pin

Floating (Don’t connected to ground)

Ground connections

－

－

－

I/O

Floating (Don’t connected to ground)

Ground connections

I Power up/down internal regulators used by BT section

－ Floating (Don’t connected to ground)

Ground connections

GPIO configuration pin

I/O

I/O

I/O

O

O

I

I

－

－

－

GPIO configuration pin

GPIO configuration pin

GPIO configuration pin

Bluetooth UART interface

Bluetooth UART interface

Bluetooth UART interface

Bluetooth UART interface

Floating (Don’t connected to ground)

Floating (Don’t connected to ground)

Floating (Don’t connected to ground)

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

15

AP6255 Datasheet

8. Dimensions

8.1 Physical Dimensions

(Unit: mm)

< TOP VIEW > < Side View >

< TOP VIEW >

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

16

8.2 Layout Recommendation

(Unit: mm)

< TOP VIEW >

AP6255 Datasheet

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

17

AP6255 Datasheet

9. External clock reference

External LPO signal characteristics

Parameter

Nominal input frequency

Frequency accuracy

Duty cycle

Input signal amplitude

Signal type

Input impedance

Specification

32.768

± 30

30 - 70

400 to 1800

Square-wave

>100k

<5

<1

0.7Vio - Vio

Clock jitter (integrated over 300Hz – 15KHz)

Output high voltage

Units kHz ppm

% mV, p-p

-

Ω pF

Hz

V

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

18

AP6255 Datasheet

10.1 SDIO Pin Description

All three package options of the WLAN section provide support for SDIO version 3.0 including the new UHS-I modes:

DS: Default speed up to 25MHz (3.3V signaling).

HS: High speed up to 50MH (3.3V signaling).

SDR12: SDR up to 25MHz (1.8V signaling).

SDR25: SDR up to 50MHz (1.8V signaling).

SDR50: SDR up to 100MHz (1.8V signaling).

SDR104: SDR up to 208MHz (1.8V signaling).

DDR50: DDR up to 50MHz (1.8V signaling).

The SDIO interface also has the ability to map the interrupt signal on to a GPIO pin for applications requiring an interrupt different from the one provided by SDIO interface. The ability to force control of gated clocks from within the device is also provided.

The following three functions are supported:

Function 0 Standard SDIO function (Max BlockSize / ByteCount = 32B)

Function 1 Backplane Function to access the internal System On Chip (SOC) address space (Max BlockSize / ByteCount = 64B)

Function 2 WLAN Function for efficient WLAN packet transfer through DMA (Max

BlockSize/ByteCount=512B)

SDIO Pin Description

SD 4-Bit Mode

DATA0 Data Line 0

DATA1 Data Line 1 or Interrupt

DATA2 Data Line 2 or Read Wait

DATA3 Data Line 3

CLK Clock

CMD Command Line

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

19

AP6255 Datasheet

10. Host Interface Timing Diagram

10.1 Power-up Sequence Timing Diagram

The module has signals that allow the host to control power consumption by enabling or disabling the Bluetooth, WLAN and internal regulator blocks. These signals are described below.

Additionally, diagrams are provided to indicate proper sequencing of the signals for carious operating states. The timing value indicated are minimum required values: longer delays are also acceptable.

※ WL_REG_ON: Used by the PMU to power up or power down the internal regulators used by the WLAN section. When this pin is high, the regulators are enabled and the WLAN section is out of reset. When this pin is low the WLAN section is in reset.

※ BT_REG_ON: Used by the PMU to power up or power down the internal regulators used by the BT section. Low asserting reset for Bluetooth. This pin has no effect on

WLAN and does not control any PMU functions. This pin must be driven high or low

(not left floating).

WLAN=ON, Bluetooth=ON

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

20

AP6255 Datasheet

WLAN=OFF, Bluetooth=OFF

WLAN=ON, Bluetooth=OFF

WLAN=OFF, Bluetooth=ON

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

21

10.2 SDIO Default Mode Timing Diagram

AP6255 Datasheet

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

22

AP6255 Datasheet

10.3 SDIO High Speed Mode Timing Diagram

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

23

AP6255 Datasheet

10.4 SDIO Bus Timing Specifications in SDR Modes

Clock timing (SDR Modes)

Card Input timing (SDR Modes)

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

24

Card output timing (SDR Modes up to 100MHz)

AP6255 Datasheet

Card output timing (SDR Modes 100MHz to 208MHz)

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

25

AP6255 Datasheet

∆ t

OP Consideration for Variable Data Window (SDR 104 Mode)

10.5 SDIO Bus Timing Specifications in DDR50 Mode

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

26

Data Timing

AP6255 Datasheet

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

27

AP6255 Datasheet

11. Recommended Reflow Profile

Referred to IPC/JEDEC standard.

Peak Temperature : <250°C

Number of Times : ≤ 2 times

2.5

℃ /sec

250 ℃

40~70 sec

2.5

°

C/sec

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

28

AP6255 Datasheet

Solder Paste definition

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

29

12. Package Information

12.1 Label

Label A Anti-static and humidity notice

AP6255 Datasheet

Label B MSL caution / Storage Condition

Label C Inner box label .

Label D Carton box label .

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

30

AP6255 Datasheet

12.2 Dimension

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

31

B

AP6255 Datasheet

Humidity indicator

Desiccant

A

C

C

D

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

32

12.3 MSL Level / Storage Condition

AP6255 Datasheet

※

NOTE : Accumulated baking time should not exceed 96hrs

AMPAK Technology Inc. www.ampak.com.tw

Proprietary & Confidential Information

Doc. NO:

33

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter.

This End equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

IMPORTANT NOTE:

In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.

End Product Labeling

The final end product must be labeled in a visible area with the following:

“Contains FCC ID: 2AFG6-RK3399”.

Manual Information to the End User

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module.

Canada Statement

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :

(1) l’appareil ne doit pas produire de brouillage;

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

Caution Exposure:

This device meets the exemption from the routine evaluation limits in section 2.5 of RSS102 and users can obtain Canadian information on RF exposure and compliance.

Le dispositif répond à l'exemption des limites d'évaluation de routine dans la section 2.5 de RSS102 et les utilisateurs peuvent obtenir des renseignements canadiens sur l'exposition aux RF et le respect. the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;

Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) des bandes de 5 250 à 5 350 MHz et de 5

650 à 5 850 MHz et, d’autre part, que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs de RL-EL. for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate.

le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point, selon le cas.

The final end product must be labelled in a visible area with the following:

The Industry Canada certification label of a module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labelled to display the Industry Canada certification number of the module, preceded by the words “Contains transmitter module”, or the word

“Contains”, or similar wording expressing the same meaning, as follows:

Contains transmitter module IC: 22166-RK3399

The module must be installed in

Android Module

This End equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

Cet équipement devrait être installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps.

The end user manual shall include all required regulatory information/warning as show in this manual.

This radio transmitter (RK3399) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Le présent émetteur radio (RK3399) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.

2.4G:

5G: