HON HAI Precision Ind. MCLJ27H003 WirelessModule User Manual

BCM94318SDIO driver install on Windows XP

How to Install BCM94318 SDIO Driver with Arasan Adapter Card on Windows

XP

Revision 1.0

Date: December 9, 2005

Page 1

Broadcom Confidential and Proprietary

BCM94318SDIO driver install on Windows XP

Copyright © 2005 Broadcom Corporation

All Rights Reserved

No part of this document may be reproduced, in any form or by any means, without permission in writing from Broadcom Corporation.

Broadcom Corporation reserves the right to make changes to the products or information contained in this document without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such products or information.

Epigram, InsideLine, and iLine10 are trademarks of Broadcom Corporation.

Broadcom Corporation

190 Mathilda Place

Sunnyvale CA 94086 www.broadcom.com

Page 2

Broadcom Confidential and Proprietary

BCM94318SDIO driver install on Windows XP

Contents

1.

INSTALL ARASAN STARDARD SD HOST PCI BOARD ...........................................................4

2.

INSTALL WIRELESS DEVICE DRIVER ........................................................................................5

Page 3

Broadcom Confidential and Proprietary

BCM94318SDIO driver install on Windows XP

1. Install Arasan Standard SD Host PCI Board

1.1 Shutdown the computer and plug in the Arasan Standard SD Host PCI card on PCI slot and reboot the PC.

1.2 Uninstall Microsoft SDIO drivers. We will be using our own instead of Microsoft’s o

Device Manager -> Find entry for Secure Digital IO Bus (or winPCI)-

>Right click-> Uninstall

1.3 Uninstall BRCM wl driver. Get rid of any previous BRCM wireless driver. o

Device manager - >Networks -> Broadcom driver->Right click/uninstall

1.4 Edit c:\windows\inf\sdbus.inf: o

Search for the section '[Generic]'. Comment out these lines by inserting a semicolon ';' in the first column, like so:

[Generic]

;PCI\CC_080500.DeviceDesc%=SDHost,PCI\CC_080500

;PCI\CC_080501.DeviceDesc%=SDHost,PCI\CC_080501

Also comment out these lines:

;PCI\CC_080500.DeviceDesc="SDA Standard Compliant SD Host

Controller"

;PCI\CC_080501.DeviceDesc="SDA Standard Compliant SD Host

Controller"

1.5

Rename sdbus.PNF to sdbus_old.PNF

1.6

Edit c:\windows\inf\usb.inf. o

Search for any line containing '1095' (which is the Arasan/CMD Vendor

ID). Comment out these lines by inserting a ';' in the first column.

1.7

Rename usb.PNF to usb_old.PNF

1.8

Reboot the PC

1.9

Note: The system must have a Windows XP and SP2 pre-installed.

Page 4

Broadcom Confidential and Proprietary

BCM94318SDIO driver install on Windows XP

2.

Install Wireless Device Driver

2.1 Finding new wireless device. Do not use Windows update for searching software.

2.2 Install from a list of locations.

Page 5

Broadcom Confidential and Proprietary

BCM94318SDIO driver install on Windows XP

2.3 Choose the driver to install

2.4 Select Hardware Type as Network Device and clink on Next

Page 6

Broadcom Confidential and Proprietary

BCM94318SDIO driver install on Windows XP

2.5 Click on “Have Disk”

2.6

Browse to the driver directory

Page 7

Broadcom Confidential and Proprietary

BCM94318SDIO driver install on Windows XP

2.7

Select “Broadcom 802.11g Network Adapter Card”

2.8

Waiting while install software

2.9

Click on “finish” to complete installation

Page 8

Broadcom Confidential and Proprietary

BCM94318SDIO driver install on Windows XP

低功率電波幅性電機管理辦法

第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功

率或變更原設計之特性及功能。

第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並

改善至無干擾時方得繼續使用。

前項合法通信，指依電信規定作業之無線電信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性

電機設備之干擾。

“Operation is subject to the following two conditions:(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.” This Class B digital apparatus complies with Canada RSS-210. Cet appareil numerique de la classe B est conforme a la norme CNR -210 du Canada The abbreviation,

IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.(DoC) The term “IC:” before the certification/registration number only signifies that the Industry Canada technical specifications

were met.

Page 9

Broadcom Confidential and Proprietary

BCM94318SDIO driver install on Windows XP

This device is intended only for OEM integrators under the following conditions:

The antenna must be installed such that 20 cm is maintained between the antenna and users. As long as conditions above is met, further transmitter test will not be required.

However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).

This device is intended only form OEM integrators under the following conditions:

1) The antenna must be installed such that 20cm is maintained between the antenna and users, and

2) The transmitter module may not be co-located with any other transmitter or antenna.

IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.

End Product Labeling

This transmitter module is authorized only for use in devices where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in visible area with the following: "Contains TX FCC ID: MCLJ27H003 manual information that Must be include."

Page 10

Broadcom Confidential and Proprietary

BCM94318SDIO driver install on Windows XP

End Product Manual Information

The user manual for end users must include the following information in a prominent location " IMPORTANT NOTE" :

To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

　

如使用本模組之平台,無法在外部看見審驗合格標籤時，

應再該平台的外部明顯處標示內含射頻模組 CCXXxxYYyyyZzW

Page 10

Broadcom Confidential and Proprietary