INMUSIC BRANDS Y4O-TS112W Speaker User Manual

ALTO
PROFESSIONAL
TSilew
TRUESONIC
QUICKSTART GUIDE
ENGLISH
ALTO
BOX CONTENTS
e Truesonic Wireless speaker
. Power cable
. Quickstart Guide
e safety Instructions & Warranty Information Booklet
INSTALLATION
Example:
This speaker should be installed on a stand on the
floor, according to its maximum weight, or Suspended
from its suspension points (M10 x 1.5PH, 30mm
length) (see example image). We do NOT recommend
Suspending multiple speakers in a vertical array.
___ Eyebolt
Dust cover
Suspension
point
CONNECTION DIAGRAM
Microphones”
PROFESSIONAL FROFESSIONAL
E KA) ©
Speaker ОГО FOTO Speaker“
É
06066 of
hr à
COCO OF
This diagram 15 a suggestion for setting up the speaker with audio connections. To pair
the speaker with a Bluetooth'" device, see the BLUETOOTH PAIRING & LINKING
section below.
“Note: Microphones, mixer, and cables are not included. Second Truesonic Wireless
speaker sold separately.
BLUETOOTH PAIRING & LINKING
IMPORTANT:
e These steps are for wireless audio streaming only.
e When pairing or linking, do only one process at a time. Starting one process before the other is finished
will cance! the first.
e [he tone sequences for pairing and linking are different, so you can easily distinguish between the two.
ABOUT RANGE
Truesonic wireless loudspeakers use an advanced, extended-range Bluetooth antenna design, allowing for
ranges far greater than traditional Bluetooth devices. The typical range Is 60-80 feet (18-24 meters) with a
clear line of sight. However, the range may vary depending on your source device and the environment.
To maximize the range:
e Set your source device on a flat surface and make sure there are no obstacles between the
loudspeaker and your device (e.g., walls, furniture, etc.).
e [Turn off your source device s WI-FI.
e Turn off any unneeded 2.4 GHz devices In the nearby vicinity (e.g., other Bluetooth devices, baby
monitors, Wi-Fi access points, microwave ovens, etc.).
e Try using a different Bluetooth source device. Bluetooth signal strength varies between different
devices.
PAIRING
To pair the speaker to your Bluetooth device:
1. With the loudspeaker powered on, press and release its BLUETOOTH PAIRING BUTTON. Its LED will
flash, and you will hear a tone sequence from the loudspeaker.
2. From your Bluetooth device s settings page, enable
Bluetooth and select ALTO PRO WIRELESS Note: If your device prompts you to enter
15112W as the device. When paired successfully, a PIN code to pair it to the speaker, enter
you will hear a final “confirmation tone” from the 0000 (four zeros).
loudspeaker and the BLUETOOTH PAIRING
BUTTON LED will light continuously. (This process
may take up to 60 seconds. )
Note: If your device prompts you to select the connection type, select “stereo speakers,” “advanced
audio, or a similar option.
3. Turn the loudspeakers BLUETOOTH VOLUME knob to Its lowest setting.
4. On your Bluetooth device, play music. We recommend setting the playback volume at Its maximum
setting. Then, adjust the loudpeakers BLUETOOTH VOLUME knob to the desired level.
5. Once your device is paired to the speaker, the speaker will remember the device even after power-
cycling It. To reconnect, go to your devices settings page and select “Connect to re-establish the
connection.
LINKING
If you are using two Truesonic wireless speakers:
1. Press and release the LINK BUTTON on both || Note: The loudspeaker that is connected
speakers. to your source device is the “master; the
2. Вой loudspeakers’ LEDs will flash while linked loudspeaker is the “slave.” Ihe
searching for each other, and you will hear a tone source device sends its signal to the
sequence from both loudspeakers. (This process master, and the master relays the signal to
may take up to 60 seconds. However, the very first the slave.
time you link the loudspeakers, the process may
take up to 3 minutes.)
3. When they are successfully linked, you will hear a final “confirmation tone” from both loudspeakers and
the LINK BUTTON LEDs on both loudspeakers will light continuously.
Note: The stereo signal will be split between the two loudspeakers: the master loudspeaker will play the left
channel; the slave loudspeaker will play the right channel.
Tip: When using two loudspeakers, we recommend labeling the master loudspeaker so you can aistinguish
between the two in future setups.
Bluetooth is a registered trademark of Bluetooth SIG.
—— о
ADDITIONAL INFORMATION
Truesonic wireless loudspeakers will remember their pairing | И
and linking settings even after they are powered off. When Tip: Once your device Is paired fo the speaker,
you turn the loudspeakers back on, they will automatically the speaker will remember ihe device even after
reconnect to each other. When the connections are re- power-cycling i. Го reconnect, go fo aed
established between the loudspeakers, the LEDs next to the device $ settings page and select "Connect to
LINK BUTTONS will light continuously. re-establish the connection.
lf the connection 1$ lost between the loudspeakers, or between the loudspeaker and the source device, or if they do
not reconnect automatically, then power-cycle both loudspeakers and go to your device s settings page and select
"Connect to re-establish the connection.
When the two loudspeakers are linked, you can only palr your source device to the master loudspeaker. The slave
loudspeakers BLUETOOTH PAIRING BUTTON will be disabled; If you press it, you will hear 3 rapid “beeps” to
indicate that the button Is “locked out.”
To erase all previous pairing and linking settings, press and hold either the BLUETOOTH PAIRING BUTTON or
the LINK BUTTON for 3 seconds. You will hear a long tone to confirm its pairing and linking settings have been
erased. The LEDs will also turn off. Do this on both the master and the slave loudspeakers. Now, you can pair to a
new source device or link the loudspeakers again.
Note: The volume of the pairing and linking tones are pre-set to an optimal level. To adjust their volume, see the
REAR PANEL OVERVIEW section for information.
REAR PANEL OVERVIEW
1. POWER INPUT - Connect the included power cable to this / A
input and connect the other end of the cable to a power |
source. Make sure the loudspeakers POWER SWITCH Is
E Bluetooth
i
\
Step I: Prosa button to pair your Blostooth an
devices, Select ALTO P ar WIRELESS in L
your devios 4,
set to "off" when plugging and unplugging the cable. ree coma, "ut
2. | POWER SWITCH - Turns the loudspeaker on/off. Make Ne) nan pat Re
sure the VOLUME knob 1$ set to “zero” before turning It on. | E ti ur Ne ida ra Let dirai
3. POWER LED - Шитпае$ when the loudspeaker Is on. / oN
4. BLUETOOTH PAIRING BUTTON - Press and release this : > >
Ш or
zu СЧ
button to pair the loudspeaker to your Bluetooth device.
see the BLUETOOTH PAIRING & LINKING section for
pairing instructions.
5: BLUETOOTH VOLUME — Тит this Knob to adjust the
input volume of your paired Bluetooth device.
6. LINK BUTTON - When using a pair of Truesonic Wireless
loudspeakers, press and release this button on each
speaker to “link” them wirelessly. See the BLUETOOTH
PAIRING & LINKING section for more information.
7. INPUT — Use a standard 1/4” TRS or XLR cable (not
included) to connect your sound source to this input. AC INPUT
8. INPUT VOLUME — Turn this Knob to adjust the input / | \\
volume for each INPUT. (1)
9. SIGNAL LIMIT LED — llluminates RED when the internal \
protection circuit Is activated by a high signal level. The
protection circult dynamically reduces the signal level to
avoid audible distortion and to protect the woofer and high-
frequency driver from over excursion or mechanical 4 y
damage. lí the LED is lit constantly, or the sound is distorted, reduce the signal level of your sound source, or
lower the volume control on the rear panel.
10. MIX OUT - Use a standard XLR cable (not included) to connect this jack to the Input of another loudspeaker.
11. MIX OUT SELECTOR - When disengaged (PRE VOL), the MIX OUT level will be unaffected by the INPUT
VOLUME controls. When engaged (POST VOL), the MIX OUT level can be adjusted by the INPUT VOLUME
controls.
Note: The BLUETOOTH VOLUME control always affects the MIX OUT.
12. CONTOUR - Engage (depress) this switch to equalize the mix for optimal music playback. Disengage (raise)
the switch during live performance for a flatter response.
13. GROUND SWITCH - Press this switch to reduce hum or noise.
14. PAIRING/LINKING TONE VOLUME - Below and to the left of the LINK BUTTON, there Is a small opening that
exposes a recessed level control. This potentiometer controls the volume of the palring/linking tones. This 1$
pre-set to an optimal volume by default, but you may use a small, flathead jeweler's screwdriver to adjust It
from -= dB to +10 dB. (Turning it clockwise increases the volume; counter-clockwise decreases It.) To return It
to the factory setting, turn it until It you feel the center detent at the 12 o clock position.
Г ВОНА
8, LIMIT
Pa €) POWER
Ml PRE VOL
ame POST WOOL
GROUND
# | i
SPECIFICATIONS
Output Power:
Crossover:
Max SPL O im:
Frequency Response:
Frequency Range:
Low Frequency:
High Frequency:
Horn Coverage:
Input Control:
External Control:
Connectors:
Wireless connectivity:
Wireless range:
Protection features:
Power supply:
Cabinet:
Mounting information:
Dimensions (H x W x D):
Weight (speaker only):
800 W Peak (670 W LF + 130 W HF)
400 W Continuous RMS (335 W LF + 65 W HF)
2.5 kHz
125 dB Peak, 122 dB Continuous
65 Hz — 19 kHz (+3 dB)
54 Hz - 20 kHz (O -10 dB)
12° (305 mm) woofer, 2° (51 mm) voice coll
Neodymium compression driver, 1° (25 mm) exit, 1° (25 mm) voice coll
80/100° H x 60° V, nominal (@ -6 dB)
Line/Mic —x to +50 dB
Max input level: +23 dBu
Impedance: 15 КО
Volume, power on/off with LED, clip limiter with LED, ground lift
Input: Two 1/4" TRS or XLR
Link: One XLR
Bluetooth (A2DP)
60-80 feet (18-24 meters), typical
Over-excursion, thermal, driver
100 VAC, 110-120 VAC, or 220-240 VAC; 50/60 Hz
Trapezoidal with floor monitor capability. Injection-molded polypropylene
with perforated steel grille
Integrated pole socket (36 mm diameter): 2 handles; 5 M10 threaded
sockets (2 top, 2 bottom, 1 pullback)
25.5 x 15.1 x 14.4° (648 mm x 384 mm x 365 mm)
36.2 Ibs. (16.4 kg)
SPECIFICATIONS
FCC ID: Y40-TS112W
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT
ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
SHIELDED CABLES MUST BE USED WITH THIS UNIT TO ENSURE COMPLIANCE WITH THE CLASS B FCC LIMITS.
Inrush current at initial switch-on: 4.76 A
Inrush current after power supply interruption: 4.64 A
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, If not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
o Reorient or relocate the receiving antenna.
o Increase the separation between the equipment and receiver.
o Connect the equipment into an outlet on a circuit different from that to which the receiver is
needed.
o Consult the dealer or an experienced radio/TV technician for help.
Bluetooth PIN +: 0000
www.altoprofessional.com
MANUAL VERSION 1.2B