Model Name
Project code
Description
Version
Issue Date
SN10-12 SIGFOX Module
User Guide and Product Specification
SN10-12
SIGFOX module
1.0
2017/09/12
Approved by
Harrison Chen
Reviewed by
Taka Wei
Issued by
Iestyn Chen
SN10-12
REV 1.0 9/12/2017
Revision History
Revision Released Date Comments/Remark Author
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
2017/03/14
2017/03/17
2017/03/24
2017/03/29
2017/06/05
2017/07/11
2017/08/04
2017/08/08
Initial release Iestyn Chen
Update with RX performance spec. Iestyn Chen
Add module layout guide and appendix section Iestyn Chen
Update RX value, reflow profile, and section 5.3 typo
Iestyn Chen
Update reference circuit Iestyn Chen
Update RCZ4 related information and add module photo
Iestyn Chen
Add standby current information, update block diagram, reference circuit and pin description
Iestyn Chen
Add pin assignment, type approval and packing specification information, update reference circuit and pin name
Iestyn Chen
Update pin type and description Iestyn Chen
Update FCC statement, and ME drawing Iestyn Chen
0.9
1.0
2017/08/18
2017/09/12
® 2017 InnoComm Mobile Technology Corp.
GENERAL NOTICE
THE USE OF THE PRODUCT INCLUDING THE SOFTWARE AND DOCUMENTATION (THE "PRODUCT") IS SUBJECT TO THE
RELEASE NOTE PROVIDED TOGETHER WITH THE PRODUCT. IN ANY EVENT THE PROVISIONS OF THE RELEASE NOTE
SHALL PREVAIL. THIS DOCUMENT CONTAINS INFORMATION ABOUT INNOCOMM PRODUCTS. THE SPECIFICATIONS IN
THIS DOCUMENT ARE SUBJECT TO CHANGE AT INNOCOMM'S DISCRETION. INNOCOMM MOBILE TECHNOLOGY
GRANTS A NON-EXCLUSIVE RIGHT TO USE THE PRODUCT. THE RECIPIENT SHALL NOT TRANSFER, COPY, MODIFY,
TRANSLATE, REVERSE ENGINEER, CREATE DERIVATIVE WORKS; DISASSEMBLE OR DECOMPILE THE PRODUCT OR
OTHERWISE USE THE PRODUCT EXCEPT AS SPECIFICALLY AUTHORIZED. THE RECIPIENT UNDERTAKES FOR AN
UNLIMITED PERIOD OF TIME TO OBSERVE CONFIDENTIALLITY REGARDING ANY INFORMATION AND DATA PROVIDED
TO THEM IN THE CONTEXT OF THE DELIVERY OF THE PRODUCT. THIS GENERAL NOTE
SHALL BE GOVERNED AND CONSTRUED ACCORDING TO TAIWAN LAW.
Copyright
Transmittal, reproduction, dissemination and/or editing of this document as well as utilization of its contents and communication thereof to others without express authorization are prohibited. Offenders will be held liable for payment of damages. All rights created by patent grant or registration of a utility model or design patent are reserved.
Copyright © 2017, InnoComm Mobile Technology Corp.
Trademark Notice
InnoComm® is the trademarks of InnoComm Mobile Technology Corp.
Other trademarks and registered trademarks mentioned herein are the property of their respective owners.
2/14
InnoComm Mobile Technology Confidential
SN10-12
REV 1.0 9/12/2017
TABLE OF CONTENT
1.
INTRODUCTION .......................................................................................................... 4
2. PIN MAP AND SIGNAL DESCRIPTION ......................................................................... 5
3. ELECTRICAL CHARACTERISTICS ............................................................................... 6
4. RF CHARACTERISTICS ................................................................................................. 7
5. SMT SOLDER REFLOW RECOMMENDATION ............................................................. 8
6. SW INFORMATION AND USER GUIDE ......................................................................... 9
7. PACKING SPECIFICATION .......................................................................................... 12
FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT .............. 13
RADIATION EXPOSURE STATEMENT: .......................................................................... 14
3/14
InnoComm Mobile Technology Confidential
SN10-12
REV 1.0 9/12/2017
1.
Introduction
The SN10-12 is a SIGFOX verified and FCC, ACMA approved transceiver module which complies with SIGFOX network specifications. It is based on NXP OL2385 chip which is a Sub-GHz wireless
SoC transceiver.
1.1.
Key Features
•
•
•
•
•
•
•
•
•
•
•
High performance low power RISC micro-controller
Memory
•
•
32kB EROM
7kB RAM
Ultra Narrow Band Radio
•
•
Frequency Band
RCZ2: 902.1375-904.6625MHz
RCZ4: 920.1375MHz-922.6625MHz
Output Power
22 dBm
Excellent Receiving Sensitivity: -125dBm @600bps 2GFSK
Excellent Image Rejection: 60 dB
Excellent Blocking Performance: 58 dB
SIGFOX™ certified module
FCC compliant (FCC ID: YAISN10-12T)
ACMA compliant
Brazil Anatel compliant
RoHS compliant
4/14
InnoComm Mobile Technology Confidential
SN10-12
REV 1.0 9/12/2017
2. PIN Map and Signal Description
Pin # Pin Name Type
22
23
24
25
26
27
16
17
18
19
20
21
28
29
30
8
9
10
11
12
13
14
15
4
5
6
7
1
2
3
31
32
Reserved
Reserved
RST_N
Reserved
Reserved
GND
SPI_AK
Reserved
Reserved
Reserved
Reserved
GND
Reserved
Reserved
GND
GND
VDD
GND
GND
GND
GND
GND
GND
SPI_SDI
SPI_CS
GND
GND
SPI_SCLK
SPI_SDO
Reserved
ANT
GND
Description
GND
Power
GND
GND
GND
GND
GND
GND
Digital I
Digital I/O
GND
GND
Digital I/O
Digital O
Digital I/O
Digital I/O
Digital I/O
N.C.
N.C.
Digital I/O RESET, active Low, with internal pull–up
Digital I/O
Digital I/O
GND
N.C.
N.C.
Ground
Digital I/O
Digital I/O
Digital I/O
Digital I/O
Digital I/O
GND
Digital I/O
Digital I/O
GND
RF
GND
SPI_AK
N.C.
N.C.
N.C.
N.C.
Ground
N.C.
N.C.
Ground
RF Antenna Interface
Impedance=50 Ω
Ground
Ground
Power Supply input
Ground
Ground
Ground
Ground
Ground
Ground
SPI_MOSI
SPI_CS
Ground
Ground
SPI_SCLK
SPI_MISO
N.C.
5/14
InnoComm Mobile Technology Confidential
SN10-12
REV 1.0 9/12/2017
3. ELECTRICAL CHARACTERISTICS
3.1 Absolute Maximum Rating
PARAMETER
Storage temperature range
Supply voltage
Maximum RX input level without damage
CONDITIONS
VDD
3.2 Recommended Operating Range
MIN TYP MAX
–55
-0.3
150
3.6
10
PARAMETER
Operating temperature range
CONDITIONS
Operating supply voltage
3.3 Power Consumption
MIN TYP MAX
–40 25 85
3.3 3.6
UNIT
°C
V dBm
UNIT
°C
V
PARAMETER
TX supply current at maximum output power
RX
Standby
CONDITIONS
@22dBm, 3.3V
3.3V
3.4 Characterization information
MIN TYP MAX
260
17.5
4.4
CONDITIONS
UNIT mA mA uA
MIN TYP MAX
-0.3 VDD + 0.3
UNIT
V
PARAMETER
Voltage at I/O pins
6/14
InnoComm Mobile Technology Confidential
SN10-12
REV 1.0 9/12/2017
4. RF Characteristics
PARAMETER
Center Frequency
PARAMETER
Antenna port impedance
Model Frequency Band
SN10-12 RCZ2: 902.1375-904.6625MHz
RCZ4: 920.1375MHz-922.6625MHz
CONDITIONS MIN TYP MAX
50
UNIT Note
MHz RCZ2
RCZ4
UNIT Note
Ω
TX Characteristics
Following characteristics are valid for conditions as follows (unless otherwise specified)
Tamb = -40 °C to 85 °C, VDD = 3.3 V to 3.6 V, TCXO = 27.6 MHz
PARAMETER CONDITIONS MIN TYP MAX UNIT
Co-channel rejection 2GFSK jammer 2 5
Note
Maximum output power, CW mode
RX Characteristics
SN10-12 22 dBm
Following characteristics are valid for conditions as follows (unless otherwise specified)
2GFSK modulation, h = 2.67, BT = 1.0, NRZ, data-rate = 0.6 kChips/s, Channel spacing = 10 kHz,
Channel filter bandwidth = 10 kHz, Frame Error Rate (FER) = 20%, payload length = 228 byte,
TCXO = 27.6 MHz
Tamb = 25 °C, VDD = 3.3 V to 3.6 V, fC = 905 MHz
PARAMETER CONDITIONS MIN TYP MAX UNIT Note
Sensitivity -40 °C to 85 °C -125 dBm PER at
10% on
1000 frames sent. dB
Adjacent channel rejection
Channel filter
BW = 10 kHz,
Channel: 10 kHz, 20 kHz,
150 kHz
50 55
55 60
60 65 dB dB dB
7/14
InnoComm Mobile Technology Confidential
SN10-12
REV 1.0 9/12/2017
5. SMT Solder Reflow Recommendation
Note: Allowable reflow soldering times: 2 times base on recommended reflow profile.
8/14
InnoComm Mobile Technology Confidential
SN10-12
REV 1.0 9/12/2017
6. SW information and User Guide
SW information
The SIGFOX software driver supports MCUs. These MCUs are a subset of the MCUs supported by the Kinetis Software Development Kit (KSDK) layer.
This SW driver is built on the Analog Middleware Layer (AML), which creates an
API abstraction layer for the desired Software Development Kit (SDK).
The current implementation includes abstractions for KSDK 2.0 and S32 SDK. This allows support to be added for additional layers, such as the KSDK, without having to change the SIGFOX Software Driver itself.
The detail Commend and SPI please read the web link as below.
SigFox Software driver user guide http://cache.nxp.com/assets/documents/data/en/userguides/OL2385SWUG.pdf?fsrch=1&sr=9&pageNum=1 :
Hardware Setting
1) SN10-1x EVB
2) FRDM_KL25Z host board
3) Sigfox Network Emulator Kit (SNEK)
4) USB cable
9/14
InnoComm Mobile Technology Confidential
SN10-12
REV 1.0 9/12/2017
Setting up the command line interface
Figure 1
1) Stack the SN10-1x EVB on top of the KL25Z host boards to connect the SPI interface,
2) Connect the host board Open SDA to the PC with an USB cable,
3) KL25Z will pop up as a mass storage device. Open the folder and copy spi_sigfox_demo.srec to the folder. (ask innocomm for spi_sigfox_demo.srec),
4) Start a terminal emulator (e.g. tera term) from the PC,
5) Configure the terminal settings to 115200 baud, 8 data bit, 1 stop bit, no parity and no flow control,
6) Press the reset button on the host board. The host board will show the list of SIGFOX commands on the terminal emulator,
7) Enter the command code and follow the prompt to send the SIGFOX commands.
Description of the command codes, the data frames and the ACK frames, and the SPI protocol are available SigFox Software driver user guide , http://cache.nxp.com/assets/documents/data/en/userguides/OL2385SWUG.pdf?fsrch=1&sr=9&pageNum=1
.
10/14
InnoComm Mobile Technology Confidential
SN10-12
REV 1.0 9/12/2017
The command list screen shot
Send payload screen shot
11/14
InnoComm Mobile Technology Confidential
SN10-12
REV 1.0 9/12/2017
7. Packing Specification
12/14
InnoComm Mobile Technology Confidential
SN10-12
REV 1.0 9/12/2017
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
-
-
- Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. -
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
13/14
InnoComm Mobile Technology Confidential
SN10-12
REV 1.0 9/12/2017
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or antenna.
3) Module approval valid only when the module is installed in the tested host or compatible series of host which have similar RF exposure characteristic with equal or larger antenna separation distance.
As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following:
“Contains FCC ID:YAISN10-12T”. The grantee's FCC ID can be used only when all FCC compliance requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
14/14
InnoComm Mobile Technology Confidential
