LAYON International Electronic & Telecom TNBBS036R BluetoothStereo Headset User Manual

FCC Caution: Any changes ог modifications not expressly approved by
the party responsible for compliance could void the user's authority
to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
15.21 Information to user.
The users manual or instruction manual for an intentional or
unintentional radiator shall caution the user that changes or
modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the
equipment.
HOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in
a particular installation.
fthis equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/ TY technician for help.
For portable devices
FCC RF Radiation Exposure Statement:
4. This Transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
2. This equipment complies with FCC RF radiation
exposure limits set forth for an
uncontrolled environment. This device was tested for
bypical hand held operations with the device contacted
directly to the human body to the sides of the device.
To maintain compliance with FCC RF exposure
compliance requirements, avoid direct contact to the
transmitting antenna during transmitting.
BSO36RD
Bluetooth Stereo Headset
User Manual
Bluetooth headset should be used with the
compatible devices which support bluetooth
wireless technology. This allows you the
freedom to make any calls and enjoy the
music streaming at any time.
Please read this user manual carefully before
using the headset, and also read your device’s
user manual regarding the bluetooth function,
and pay attention to those important safety and
maintenance information.
Please keep the headset away from children.
Specifications
Bluetooth Specification V3.0
Bluetooth Profiles Supported Headset, Handsfree , A2DP, AVRCP
Transmission Power Class 2
Operation Range Up to 10 Meters
Frequency Range 2.402~2.480GHz
Battery Built-in Rechargeable
3.7V /70mAH Li-polymer Battery
Charging Voltage 064. 75-5. 25V
Charging Time About 2 hours
Music Playing Time* Up to 3.5hours
Talk Time* Up to 4 hours
Standby Time* Up to 100 hours
Dimensions(mm) L36 x W14.5 x H6
Weight About 14 9
*The time mentioned as above may vary due to user's operation
mode and device settings.
Structure Sketch
1-Volume Key+(V+)
2-Speaker
3-Volume Key-(V-)
4-Multifunction Button(MFB)
5-Charging Socket
6-Microphone
7-Earpiece
Basic Operations
Charging Your Headset
e Prior to using the headset for the first time,
please fully charge the battery.
e Approximately 2 hours are required to fully
charge the headset.
e The indicator light turns red while being
charged, and will turn to blue automatically
after being fully charged.
e When the headset is running out of battery,
the indicator light will flash red(the headset
will switch off automatically when the battery
is drained). Please charge the headset as
above steps in time to prolong the battery's
using life(Charging indication will be delayed
for a few minutes if the headset has not been
used for a long time or the battery is drained).
Note:
e Use only the supplied charger to charge the headset, or
could be dangerous and obey the validation for this product
or the maintenance article.
e Do not attempt to force open the built-in battery as this
could damage the headset.
e If left unused, a fully charged headset will loose its power
automatically. It is recommended to charge the headset
each three months.
e Do not leave the headset in a too hot or too cold condition
(best between 15°C and 25°C ) which may affect the
headset's operations although it is fully charged.
* Do not dispose of the headset into a fire or water.
Turning on the Headset
In OFF MODE, press and hold MFB for 2
seconds until you hear a short beep and the
indicator light flashes blue for 3 times, then the
headset will enter into STANDBY MODE.
Turning off the Headset
In ON MODE, press and hold MFB for 5 seconds
until you hear a short beep and the indicator
light flashes red for 3 times, then the headset
will enter into OFF MODE.
Pairing Your Headset with a
Bluetooth Mobile Phone
1.Ensure the headset is off, and the distance
between your headset and phone is within 1
meter.
2.Press and hold MFB until you hear a beep and
the indicator light flashes red and blue
alternately as PAIRING MODE.
3.Activate the bluetooth function on the phone,
and search bluetooth devices (See the user
guide of your phone for instructions).
4 Select headset “ BS036RD ” from the found
devices list of the phone.
5.Enter the passkey “0000”, confirm to pair the
headset with your phone and headset will
enter into connecting mode. (If the pairing
cannot be completed within 5 minutes after
the PAIRING MODE has been activated, the
headset will enter into the STANDBY MODE.
Repeat above steps to do the pairing again).
6.Ensure the distance between your headset
and phone is within 10 meters, and without
any obstacles, you can use the headset
freely.
7.If the headset has paired with your phone but
disconnected, it will connect the paired phone
automatically when you turn on the headset
again within operation range.
Answering a Call
Press MFB once.
Ending a Call
Press MFB once.
Rejecting a Call
Press and hold MFB for 2 seconds.
Voice Dialing
In STANDBY MODE, press MFB for about 2
seconds and say the voice tag as soon as you
hear the short beep(ensure your phone
supports voice dialing function, and you have
recorded the voice tag into your phone. See the
user guide of your phone for instructions)
Last Number Redialing
Press MFB twice.
Adjusting Volume
Press V+ or V- shortly to adjust the volume
Power Saving
The headset will turn off automatically if it can
not be paired or connected with any devices
within 20 minutes.
Audio Remote-control Function
Play/Pause
Press MFB once for music playing, and press
again to pause.
Forward
Press and hold V- button to forward to the
nextsong
Backward
Press and hold V+ button to backward to the
last song.
Note: Ensure your paired devices support AVRCP Bluetooth
Profile to realize remote-control use.
Disconnecting
To disconnect the paired headset from your
phone,please turn off the headset or
disconnect the headset from the Bluetooth
menu of your phone.
Care and Maintenance
eDo not use abrasive cleaning solvents to
clean the headset.
e Do not allow the headset to touch with any
sharp objects since this will cause
scratching and damage.
e Be sure to store the headset in a dry place,
free from extreme high temperatures,
humidity and dust.