LINKSYS Q87-WRT160NL Wireless-NBroadband Router User Manual

USER GUIDE

Wireless-N Broadband Router with Storage Link

Model: WRT160NL

About This Guide

Icon Descriptions

While reading through the User Guide you may see various icons that call attention to specific items. Below is a description of these icons:

NOTE: This check mark indicates that there is a note of interest and is something that you should pay special attention to while using the product.

WARNING: This exclamation point indicates that there is a caution or warning and it is something that could damage your property or product.

WEB: This globe icon indicates a noteworthy website address or e-mail address.

Online Resources

Website addresses in this document are listed without http:// in front of the address because most current web browsers do not require it. If you use an older web browser, you may have to add http:// in front of the web address.

Resource

Linksys

Linksys

International

Glossary

Website www.linksysbycisco.com

www.linksysbycisco.com/international www.linksysbycisco.com/glossary

Network Security www.linksysbycisco.com/security

Copyright and Trademarks

Linksys, Cisco and the Cisco Logo are registered trademarks or trademarks of

Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries.

Copyright © 2009 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders.

Wireless-N Broadband Router with Storage Link

About This Guide i

Table of Contents

Chapter 1: Product Overview 1

Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Bottom Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Chapter 2: Wireless Security Checklist 3

General Network Security Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Additional Security Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Chapter 3: Advanced Configuration 4

Setup > Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Setup > DDNS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Setup > MAC Address Clone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Setup > Advanced Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Wireless > Basic Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Wireless > Wireless Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Wireless > Wireless MAC Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Wireless > Advanced Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Security > Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Security > VPN Passthrough . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Storage > Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Storage > Media Server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Storage > Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Access Restrictions > Internet Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Applications and Gaming > Single Port Forwarding. . . . . . . . . . . . . . . . . . . . . . . .18

Applications and Gaming > Port Range Forwarding . . . . . . . . . . . . . . . . . . . . . . .18

Applications & Gaming > Port Range Triggering . . . . . . . . . . . . . . . . . . . . . . . . . .19

Applications and Gaming > DMZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Applications and Gaming > QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Administration > Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Administration > Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Administration > Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Administration > Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Administration > Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Status > Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Status > Local Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Status > Wireless Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Appendix A: Troubleshooting 27

Wireless-N Broadband Router with Storage Link ii

Table of Contents

Appendix B: How to Install and Access USB Storage 29

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Install the USB Storage Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Access the USB Storage Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Create a Shortcut to a Shared Folder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Advanced Configuration (Advanced Users Only). . . . . . . . . . . . . . . . . . . . . . . . . .32

Appendix C: Specifications 36

Appendix D: Warranty Information 37

Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Appendix E: Regulatory Information 39

FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

FCC Radiation Exposure Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Safety Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Industry Canada Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Avis d’Industrie Canada. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Wireless Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Avis de non-responsabilité concernant les appareils sans fil . . . . . . . . . . . . . . . . . .40

User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste

Electric and Electronic Equipment (WEEE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Appendix F: Software End User License Agreement 45

Cisco Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Software Licenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Wireless-N Broadband Router with Storage Link iii

Chapter 1

Chapter 1:

Product Overview

Thank you for choosing the Linksys Wireless-N Broadband

Router with Storage Link. The Router lets you access the

Internet via a wireless connection or through one of its four switched ports. You can also use the Router to share resources such as computers, printers and files. The

Router’s USB port connects to a USB storage device, so you can access your portable files. (A USB hard drive may require an external power supply.) A variety of security features help to protect your data and your privacy while you are online. Security features include WPA2 security, a Stateful Packet Inspection (SPI) firewall, and

NAT technology. Configuring the Router is easy using the provided browser–based utility.

Front Panel

1, 2, 3, 4 (Blue) These numbered LEDs, corresponding with the numbered ports on the

Router’s back panel, serve two purposes. If the

LED is continuously lit, the Router is successfully connected to a device through that port. A flashing LED indicates network activity over that port.

Wi-Fi Protected Setup Button If you have client devices, such as wireless adapters, that support Wi-Fi Protected Setup, then you can use Wi-Fi Protected Setup to automatically configure wireless security for your wireless network(s).

To use Wi-Fi Protected Setup, run the Setup

Wizard, or refer to Wi-Fi Protected Setup , page

11 .


Wi-Fi Protected Setup LED (Blue/

Amber) The LED lights up blue when wireless security is enabled. It flashes blue for two minutes during Wi-Fi Protected Setup.

The LED lights up amber if there is an error during the Wi-Fi Protected Setup process. Make sure the client device supports Wi-Fi Protected

Setup. Wait until the LED is off, and then try again.

The LED flashes when a Wi-Fi Protected Setup session is active. The Router supports one session at a time. Wait until the LED is solidly lit, or off before starting the next Wi-Fi Protected

Setup session.

Wireless (Blue) The Wireless LED lights up when the wireless feature is enabled. If the LED is flashing, the Router is sending or receiving data over the network.

Internet (Blue) The Internet LED lights up when there is a connection made through the

Internet port. It flashes to indicate network activity over the Internet port.

Power (Blue) The Power LED lights up and will stay on while the Router is powered on. When the Router goes through its self-diagnostic mode during every boot-up, this LED will flash.

When the diagnostic is complete, the LED will be solidly lit.

Back Panel


Antenna Ports The R-SMA antenna ports connect to the SMA connectors of the included antennas.

Internet The Internet port is where you will connect your cable or DSL Internet connection.

4, 3, 2, 1 These Ethernet ports (4, 3, 2, 1) connect the Router to computers on your wired network and other Ethernet network devices.

USB Port The USB port connects to a USB storage device. If the storage device does not fit

(for example, it may block port 1), then use the included USB extension cable.

Power The Power port connects to the included power adapter.

1

Chapter 1

Bottom Panel

Reset The Reset button is located on the right side of the product label. There are two ways to reset the Router’s factory defaults. Either press and hold the Reset button for approximately five seconds, or restore the defaults from the

Administration > Factory Defaults screen of the

Router’s web-based utility.

Horizontal Placement

The Router has four rubber feet on its bottom panel. Place the Router on a level surface near an electrical outlet.


Wall-Mounting Placement

The Router has two wall-mount slots on its bottom panel. The distance between the slots is 152 mm

(6 inches).

Two screws are needed to mount the Router.

Suggested Mounting Hardware

4-5 mm 1-1.5 mm

† Note: Mounting hardware illustrations are not true to scale.

NOTE: Linksys is not responsible for damages incurred by insecure wall-mounting hardware.

Follow these instructions:

1.

2.

3.

4.

5.

Determine where you want to mount the Router. Make sure that the wall you use is smooth, flat, dry, and sturdy. Also make sure the location is within reach of an electrical outlet.

Drill two holes into the wall. Make sure the holes are

152 mm (6 inches) apart.

Insert a screw into each hole and leave 3 mm

(0.12 inches) of its head exposed.

Maneuver the Router so the wall-mount slots line up with the two screws.

Place the wall-mount slots over the screws and slide the Router down until the screws fit snugly into the wall-mount slots.

152 mm

Print this page at 100% size.

Cut along the dotted line, and place on the wall to drill precise spacing.

Wall-Mounting Template

Wireless-N Broadband Router with Storage Link 2

Chapter 2

Chapter 2:

Wireless Security Checklist

Wireless networks are convenient and easy to install, so homes with high-speed Internet access are adopting them at a rapid pace. Because wireless networking operates by sending information over radio waves, it can be more vulnerable to intruders than a traditional wired network.

Like signals from your cellular or cordless phones, signals from your wireless network can also be intercepted. Since you cannot physically prevent someone from connecting to your wireless network, you need to take some additional steps to keep your network secure.

1. Change the default wireless

network name or SSID

Wireless devices have a default wireless network name or Service Set Identifier (SSID) set by the factory. This is the name of your wireless network, and can be up to 32 characters in length. Linksys wireless products use linksys as the default wireless network name. You should change the wireless network name to something unique to distinguish your wireless network from other wireless networks that may exist around you, but do not use personal information (such as your Social Security number) because this information may be available for anyone to see when browsing for wireless networks.

2. Change the default password

For wireless products such as access points and routers, you will be asked for a password when you want to change their settings. These devices have a default password set by the factory. The Linksys default password is admin .

Hackers know these defaults and may try to use them to access your wireless device and change your network settings. To thwart any unauthorized changes, customize the device’s password so it will be hard to guess.

3. Enable MAC address filtering

Linksys routers give you the ability to enable Media Access

Control (MAC) address filtering. The MAC address is a unique series of numbers and letters assigned to every networking device. With MAC address filtering enabled, wireless network access is provided solely for wireless devices with specific MAC addresses. For example, you can specify the MAC address of each computer in your home so that only those computers can access your wireless network.


Wireless Security Checklist

4. Enable encryption

Encryption protects data transmitted over a wireless network. Wi-Fi Protected Access (WPA/WPA2) and Wired

Equivalent Privacy (WEP) offer different levels of security for wireless communication.

A network encrypted with WPA/WPA2 is more secure than a network encrypted with WEP, because WPA/WPA2 uses dynamic key encryption. To protect the information as it passes over the airwaves, you should enable the highest level of encryption supported by your network equipment.

WEP is an older encryption standard and may be the only option available on some older devices that do not support WPA.

General Network Security Guidelines

Wireless network security is useless if the underlying network is not secure.

•

•

•

•

Password protect all computers on the network and individually password protect sensitive files.

Change passwords on a regular basis.

Install anti-virus software and personal firewall software.

Disable file sharing (peer-to-peer). Some applications may open file sharing without your consent and/or knowledge.

Additional Security Tips

•

•

•

Keep wireless routers, access points, or gateways away from exterior walls and windows.

Turn wireless routers, access points, or gateways off when they are not being used (at night, during vacations).

Use strong passphrases that are at least eight characters in length. Combine letters and numbers to avoid using standard words that can be found in the dictionary.

WEB: For more information on wireless security, visit www.linksysbycisco.com/security

3

Chapter 3

Chapter 3:

Advanced Configuration

After setting up the Router with the Setup Wizard (located on the CD-ROM), the Router will be ready for use. However, if you want to change its advanced settings, use the

Router’s web-based utility. This chapter describes each web page of the utility and each page’s key functions. You can access the utility via a web browser on a computer connected to the Router.

The web-based utility has these main tabs: Setup,

Wireless, Security, Access Restrictions, Applications &

Gaming, Administration, and Status. Additional tabs will be available after you click one of the main tabs.

NOTE: When first installing the Router, you should use the Setup Wizard on the Setup

CD-ROM. If you want to configure advanced settings, use this chapter to learn about the web-based utility.

How to Access the Web-Based Utility

To access the web-based utility, launch the web browser on your computer, and enter the Router’s default IP address,

192.168.1.1

, in the Address field. Then press Enter .

A login screen will appear. (Non-Windows XP users will see a similar screen.) Leave the User name field blank.

The first time you open the Web-based utility, use the default password admin . (You can set a new password from the Administration > Management screen.) Click OK to continue.

Login Screen

Setup > Basic Setup

The first screen that appears is the Basic Setup screen. This allows you to change the Router’s general settings.



Setup > Basic Setup

Language

Select your language To use a different language, select one from the drop-down menu. The language of the web-based utility will change five seconds after you select another language.

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

Internet Setup

The Internet Setup section configures the Router to your

Internet connection. Most of this information can be obtained through your Internet Service Provider (ISP).

Internet Connection Type

Select the type of Internet connection your ISP provides from the drop-down menu. These are the available types:

• Automatic Configuration - DHCP

• Static IP

• PPPoE

• PPTP

• L2TP

• Telstra Cable

Automatic Configuration - DHCP

By default, the Router’s Internet Connection Type is set to Automatic Configuration - DHCP , which should be kept only if your ISP supports DHCP or you are connecting

4

Chapter 3 through a dynamic IP address. (This option usually applies to cable connections.)

Internet Connection Type > Automatic Configuration - DHCP

Static IP

If you are required to use a permanent IP address to connect to the Internet, select Static IP .

Advanced Configuration inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. To use this option, select Connect on Demand . In the Max Idle Time field, enter the number of minutes you want to have elapsed before your Internet connection terminates. The default

Max Idle Time is 15 minutes.

Keep Alive: Redial Period If you select this option, the Router will periodically check your Internet connection. If you are disconnected, then the Router will automatically re-establish your connection. To use this option, select Keep Alive . In the Redial Period field, you specify how often you want the Router to check the Internet connection. The default Redial Period is

30 seconds.

PPTP

Point-to-Point Tunneling Protocol (PPTP) is a service that applies to connections in Europe only.

Internet Connection Type > Static IP

Internet IP Address This is the Router’s IP address, when seen from the Internet. Your ISP will provide you with the

IP Address you need to specify here.

Subnet Mask This is the Router’s Subnet Mask, as seen by users on the Internet (including your ISP). Your ISP will provide you with the Subnet Mask.

Default Gateway Your ISP will provide you with the IP address of the ISP server.

DNS 1-3 Your ISP will provide you with at least one DNS

(Domain Name System) server IP address.

PPPoE

Some DSL-based ISPs use PPPoE (Point-to-Point Protocol over Ethernet) to establish Internet connections. If you are connected to the Internet through a DSL line, check with your ISP to see if they use PPPoE. If they do, you will have to enable PPPoE .

Internet Connection Type > PPPoE

Username and Password Enter the Username and

Password provided by your ISP.

Service Name If provided by your ISP, enter the Service

Name.

Connect on Demand: Max Idle Time You can configure the Router to cut the Internet connection after it has been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated due to


Internet Connection Type > PPTP

If your ISP supports DHCP or you are connecting through a dynamic IP address, then select Obtain an IP Address

Automatically . If you are required to use a permanent IP address to connect to the Internet, then select Specify an

IP Address . Then configure the following:

•

Specify an IP Address This is the Router’s IP address, as seen from the Internet. Your ISP will provide you with the IP Address you need to specify here.

•

Subnet Mask This is the Router’s Subnet Mask, as seen by users on the Internet (including your ISP). Your

ISP will provide you with the Subnet Mask.

•

Default Gateway Your ISP will provide you with the

IP address of the ISP server.

•

DNS 1-3 Your ISP will provide you with at least one

DNS (Domain Name System) server IP address.

PPTP Server IP Address Your ISP will provide you with the IP address of the PPTP server.



5

Chapter 3

Connect on Demand: Max Idle Time You can configure the Router to cut the Internet connection after it has been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. To use this option, select Connect on Demand . In the Max Idle Time field, enter the number of minutes you want to have elapsed before your Internet connection terminates. The default


Keep Alive: Redial Period If you select this option, the

Router will periodically check your Internet connection. If you are disconnected, then the Router will automatically re-establish your connection. To use this option, select

Keep Alive . In the Redial Period field, you specify how often you want the Router to check the Internet connection. The default value is 30 seconds.

L2TP

L2TP is a service that applies to connections in Israel only.

Internet Connection Type > L2TP

Server IP Address This is the IP address of the L2TP

Server. Your ISP will provide you with the IP Address you need to specify here.






30 seconds.

Telstra Cable



Telstra Cable is a service that applies to connections in

Australia only.

Internet Connection Type > Telstra Cable

Server IP Address This is the IP address of the Heartbeat

Server. Your ISP will provide you with the IP Address you need to specify here.






30 seconds.

Optional Settings

Some of these settings may be required by your ISP. Verify with your ISP before making any changes.

Optional Settings

Host Name and Domain Name These fields allow you to supply a host and domain name for the Router. Some ISPs, usually cable ISPs, require these names as identification.

You may have to check with your ISP to see if your broadband Internet service has been configured with a host and domain name. In most cases, leaving these fields blank will work.

MTU MTU is the Maximum Transmission Unit. It specifies the largest packet size permitted for Internet transmission.

6

Chapter 3

Select Manual if you want to manually enter the largest packet size that is transmitted. To have the Router select the best MTU for your Internet connection, keep the default, Auto .

Size When Manual is selected in the MTU field, this option is enabled. Leave this value in the 1200 to 1500 range. The default size depends on the Internet Connection Type:

• DHCP, Static IP, or Telstra: 1500

• PPPoE: 1492

• PPTP or L2TP: 1460

Network Setup

The Network Setup section changes the settings on the network connected to the Router’s Ethernet ports. Wireless setup is performed through the Wireless tab.

Router IP

This presents both the Router’s IP Address and Subnet

Mask as seen by your network.

Router IP

DHCP Server Setting

The settings allow you to configure the Router’s Dynamic

Host Configuration Protocol (DHCP) server function. The

Router can be used as a DHCP server for your network. A

DHCP server automatically assigns an IP address to each computer on your network. If you choose to enable the

Router’s DHCP server option, make sure there is no other

DHCP server on your network.

DHCP Server Setting

DHCP Server DHCP is enabled by factory default. If you already have a DHCP server on your network, or you do not want a DHCP server, then select Disabled (no other

DHCP features will be available).

DHCP Reservation Click this button if you want to assign a fixed local IP address to a MAC address.

DHCP Reservation



You will see a list of DHCP clients with the following information: Client Name, Interface, IP Address, and

MAC Address.

DHCP Reservation

• Select Clients from DHCP Table Click the Select check box to reserve a client’s IP address. Then click

Add Clients .

•

Manually Adding Client To manually assign an IP address, enter the client’s name in the Enter Client

Name field. Enter the IP address you want it to have in the Assign IP Address field. Enter its MAC address in the

To This MAC Address field. Then click Add .

Clients Already Reserved

A list of DHCP clients and their fixed local IP addresses will be displayed at the bottom of the screen. If you want to remove a client from this list, click Remove .

Click Save Settings to apply your changes, or click

Cancel Changes to cancel your changes. To view the most up-to-date information, click Refresh . To exit this screen, click Close .

Start IP Address Enter a value for the DHCP server to start with when issuing IP addresses. Because the Router’s default IP address is 192.168.1.1, the Start IP Address must be 192.168.1.2 or greater, but smaller than 192.168.1.253.

The default Starting IP Address is 192.168.1.100

.

Maximum Number of Users Enter the maximum number of PCs that you want the DHCP server to assign

IP addresses to. This number cannot be greater than 253.

The default is 50 .

IP Address Range Displayed here is the range of available

IP addresses.

Client Lease Time The Client Lease Time is the amount of time a network user will be allowed connection to the

Router with their current dynamic IP address. Enter the amount of time, in minutes, that the user will be “leased” this dynamic IP address. After the time is up, the user will be automatically assigned a new dynamic IP address. The default is 0 minutes, which means one day.

7

Chapter 3

Static DNS 1-3 The Domain Name System (DNS) is how the Internet translates domain or website names into

Internet addresses or URLs. Your ISP will provide you with at least one DNS Server IP Address. If you wish to use another, enter that IP Address in one of these fields. You can enter up to three DNS Server IP Addresses here. The Router will use these for quicker access to functioning DNS servers.

WINS The Windows Internet Naming Service (WINS) manages each PC’s interaction with the Internet. If you use a WINS server, enter that server’s IP Address here.

Otherwise, leave this blank.

Time Settings

Time Zone Select the time zone in which your network functions from this drop-down menu. (You can even automatically adjust for daylight saving time.)

Time Settings



Setup > DDNS

The Router offers a Dynamic Domain Name System (DDNS) feature. DDNS lets you assign a fixed host and domain name to a dynamic Internet IP address. It is useful when you are hosting your own website, FTP server, or other server behind the Router.

Before you can use this feature, you need to sign up for DDNS service with a DDNS service provider, www.dyndns.org

or www.TZO.com

. If you do not want to use this feature, keep the default, Disabled .

DDNS

DDNS Service

If your DDNS service is provided by DynDNS.org, then select DynDNS.org

from the drop-down menu. If your

DDNS service is provided by TZO, then select TZO.com

.

The features available on the DDNS screen will vary, depending on which DDNS service provider you use.

DynDNS.org


Setup > DDNS > DynDNS

Username Enter the Username for your DDNS account.

Password Enter the Password for your DDNS account.

Host Name The is the DDNS URL assigned by the DDNS service.

System Select the DynDNS service you use: Dynamic ,

Static , or Custom . The default selection is Dynamic .

Mail Exchange (Optional) Enter the address of your mail exchange server, so e-mails to your DynDNS address go to your mail server.

Backup MX This feature allows the mail exchange server to be a backup. To disable this feature, keep the default,

Disabled . To enable the feature, select Enabled . If you are not sure which setting to select, keep the default,

Disabled .

Wildcard This setting enables or disables wildcards for your host. For example, if your DDNS address is myplace.dyndns.org

and you enable wildcards, then x.myplace.dyndns.org

will work as well (x is the wildcard).

To disable wildcards, keep the default, Disabled . To enable wildcards, select Enabled . If you are not sure which setting to select, keep the default, Disabled .

Internet IP Address The Router’s Internet IP address is displayed here. Because it is dynamic, it will change.

Status The status of the DDNS service connection is displayed here.

Update To manually trigger an update, click this button.




Chapter 3

TZO.com


Clone My PC’s MAC Click this button to clone the MAC address of the computer you are using.



Setup > Advanced Routing

This screen is used to set up the Router’s advanced functions. Operating Mode allows you to select the type(s) of advanced functions you use. Dynamic Routing automatically adjusts how packets travel on your network.

Static Routing sets up a fixed route to another network destination.

Setup > DDNS > TZO

E-mail Address, TZO Key, and Domain Name Enter the settings of the account you set up with TZO.

Internet IP Address The Router’s Internet IP address is displayed here. Because it is dynamic, it will change.

Status The status of the DDNS service connection is displayed here.

Update To manually trigger an update, click this button.



Setup > MAC Address Clone

A MAC address is a 12-digit code assigned to a unique piece of hardware for identification. Some ISPs will require you to register a MAC address in order to access the

Internet. If you do not wish to re-register the MAC address with your ISP, you may assign the MAC address you have currently registered with your ISP to the Router with the

MAC Address Clone feature.

Setup > MAC Address Clone

MAC Address Clone

Enabled/Disabled To have the MAC Address cloned, select Enabled .

MAC Address Enter the MAC Address registered with your ISP here.


Setup > Advanced Routing

Advanced Routing

NAT

Enabled/Disabled If this Router is hosting your network’s connection to the Internet, keep the default, Enabled . If another router exists on your network, select Disabled .

When the NAT setting is disabled, dynamic routing will be enabled.

Dynamic Routing (RIP)

Enabled/Disabled This feature enables the Router to automatically adjust to physical changes in the network’s layout and exchange routing tables with the other router(s).

The Router determines the network packets’ route based on the fewest number of hops between the source and the destination. When the NAT setting is enabled, the

Dynamic Routing feature is automatically disabled. When the NAT setting is disabled, this feature is available. Select

Enabled to use the Dynamic Routing feature.

Static Routing

A static route is a pre-determined pathway that network information must travel to reach a specific host or network.

Enter the information described below to set up a new static route.

9

Chapter 3

Route Entries To set up a static route between the Router and another network, select a number from the dropdown list. Click Delete This Entry to delete a static route.

Enter Route Name Enter a name for the Route here, using a maximum of 25 alphanumeric characters.

Destination LAN IP The Destination LAN IP is the address of the remote network or host to which you want to assign a static route.

Subnet Mask The Subnet Mask determines which portion of a Destination LAN IP address is the network portion, and which portion is the host portion.

Gateway This is the IP address of the gateway device that allows for contact between the Router and the remote network or host.

Interface This interface tells you whether the Destination

IP Address is on the LAN & Wireless (Ethernet and wireless networks) or the Internet (WAN) .

Click Show Routing Table to view the static routes you have already set up.

Advanced Routing > Routing Table

Routing Table

For each route, the Destination LAN IP address, Subnet

Mask, Gateway, and Interface are displayed. Click

Refresh to update the information. Click Close to exit this screen.



Wireless > Basic Wireless Settings

The basic settings for wireless networking are set on this screen.

There are two ways to configure the Router’s wireless network(s), manual and Wi-Fi Protected Setup.

Wi-Fi Protected Setup is a feature that makes it easy to set up your wireless network. If you have client devices, such as wireless adapters, that support Wi-Fi Protected Setup, then you can use Wi-Fi Protected Setup.

Wireless Configuration To manually configure your wireless network, select Manual . Proceed to the “Basic

Wireless Settings” section. To use Wi-Fi Protected Setup,


Advanced Configuration select Wi-Fi Protected Setup . Proceed to the “Wi-Fi

Protected Setup” section.

Basic Wireless Settings

Wireless > Basic Wireless Settings (Manual Setup)

Network Mode From this drop-down menu, you can select the wireless standards running on your network. If you have Wireless-N, Wireless-G, and Wireless-B devices in your network, keep the default, Mixed . If you have only

Wireless-G and Wireless-B devices in your network, select

BG-Mixed . If you have only Wireless-N devices, select

Wireless-N Only . If you have only Wireless-G devices, select Wireless-G Only . If you have only Wireless-B devices, select Wireless-B Only . If you do not have any wireless devices in your network, select Disabled .

Network Name (SSID) The SSID is the network name shared among all points in a wireless network. The

SSID must be identical for all devices in the wireless network. It is case-sensitive and must not exceed

32 characters (use any of the characters on the keyboard).

Make sure this setting is the same for all points in your wireless network. For added security, you should change the default SSID ( linksys ) to a unique name.

Channel Width For best performance in a network using

Wireless-N, Wireless-G and Wireless-B devices, select

Wide - 40MHz Channel . For Wireless-G and Wireless-B networking only, keep the default, Standard - 20MHz

Channel . If you are not sure which option to select, select

Auto .

NOTE: If you select Wide - 40MHz Channel for the Channel Width setting, then Wireless-N can use two channels: a primary one (Wide Channel) and a secondary one (Standard Channel). This will enhance Wireless-N performance.

Wide Channel If Wide - 40MHz Channel is the Channel

Width setting, then this setting will be available for your primary Wireless-N channel. Select any channel from the drop-down menu. If you are not sure which channel to select, keep the default, Auto .

10

Chapter 3

Standard Channel If Standard - 20 MHz Channel is the

Channel Width setting, then this setting will be available.

Select the appropriate channel for your wireless network.

If you are not sure which channel to select, then keep the default, Auto .

If Wide - 40MHz Channel is the Channel Width setting, then the Standard Channel will be a secondary channel for Wireless-N (2.4 GHz).

If you selected a specific channel for the Wide Channel setting, then the Standard Channel options will vary.

Select the appropriate channel for your wireless network.

SSID Broadcast When wireless clients survey the local area for wireless networks to associate with, they will detect the SSID broadcast by the Router. To broadcast the

Router’s SSID, keep the default, Enabled . If you do not want to broadcast the Router’s SSID, then select Disabled .



Wi-Fi Protected Setup

There are three methods available. Use the method that applies to the client device you are configuring.


Wi-Fi Protected Setup Configured

NOTE: Wi-Fi Protected Setup configures one client device at a time. Repeat the instructions for each client device that supports Wi-Fi

Protected Setup.

Method #1

Use this method if your client device has a Wi-Fi Protected

Setup button.

1.

2.

3.

Click or press the the client device.

Wi-Fi Protected Setup button on

Click the screen.

Wi-Fi Protected Setup button on this

After the client device has been configured, click

OK . Then refer back to your client device or its documentation for further instructions.

Wireless > Basic Wireless Settings (Wi-Fi Protected Setup)


Wi-Fi Protected Setup > Congratulations

Method #2

Use this method if your client device has a Wi-Fi Protected

Setup PIN number.

1.

2.

Enter the PIN number in the field on this screen.

Click Register .

11

Chapter 3

3. After the client device has been configured, click


Method #3

Use this method if your client device asks for the Router’s

PIN number.

1.

2.

Enter the PIN number listed on this screen. (It is also listed on the label on the bottom of the Router.)

After the client device has been configured, click


The Wi-Fi Protected Setup Status, Network Name (SSID),

Security, Encryption, and Passphrase are displayed at the bottom of the screen.

NOTE: If you have client devices that do not support Wi-Fi Protected Setup, note the wireless settings, and then manually configure those client devices.

Wireless > Wireless Security

The Wireless Security screen configures the security of your wireless network. There are six wireless security mode options supported by the Router: WPA Personal,

WPA Enterprise, WPA2 Personal, WPA2 Enterprise, RADIUS, and WEP. (WPA stands for Wi-Fi Protected Access, which is a security standard stronger than WEP encryption. WEP stands for Wired Equivalent Privacy, while RADIUS stands for Remote Authentication Dial-In User Service.) These six are briefly discussed here. For detailed instructions on configuring wireless security for the Router, refer to

“Chapter 2: Wireless Security.”

Wireless Security

Security Mode

Select the security method for your wireless network. If you do not want to use wireless security, keep the default,

Disabled .

WPA Personal

NOTE: If you are using WPA, always remember that each device in your wireless network MUST use the same WPA method and shared key, or else the network will not function properly.


Security Mode > WPA Personal

Encryption WPA supports two encryption methods, TKIP and AES, with dynamic encryption keys. Select the type of algorithm, TKIP or AES . The default is TKIP .

Passphrase Enter a Passphrase of 8-63 characters.

Key Renewal Enter a Key Renewal period, which instructs the Router how often it should change the encryption keys.

The default Group Key Renewal period is 3600 seconds.

WPA2 Personal

Security Mode > WPA2 Personal

Encryption WPA2 supports two encryption methods,

TKIP and AES, with dynamic encryption keys. Select the type of algorithm, AES or TKIP or AES . The default is TKIP or AES .

Passphrase Enter a Passphrase of 8-63 characters.

Key Renewal Enter a Key Renewal period, which instructs the Router how often it should change the encryption keys.

The default Group Key Renewal period is 3600 seconds.

WPA Enterprise

This option features WPA used in coordination with a

RADIUS server. (This should only be used when a RADIUS server is connected to the Router.)


Chapter 3


Shared Secret Enter the key shared between the Router and the server.

Key Renewal Enter a Key Renewal period, which instructs the Router how often it should change the encryption keys. The default Key Renewal period is 3600 seconds.

RADIUS

This option features WEP used in coordination with a


Security Mode > WPA Enterprise

Encryption WPA supports two encryption methods, TKIP and AES, with dynamic encryption keys. Select the type of algorithm, TKIP or AES . The default is TKIP .

RADIUS Server Enter the IP Address of the RADIUS server.

RADIUS Port Enter the port number of the RADIUS server. The default value is 1812 .


Key Renewal Enter a Key Renewal period, which instructs the Router how often it should change the encryption keys. The default Key Renewal period is 3600 seconds.

WPA2 Enterprise

This option features WPA2 used in coordination with a


Security Mode > WPA2 Enterprise

Encryption WPA2 supports two encryption methods,

TKIP and AES, with dynamic encryption keys. Select the type of algorithm, AES or TKIP or AES . The default is TKIP or AES .




Security Mode > RADIUS

IMPORTANT: If you are using WEP encryption, always remember that each device in your wireless network MUST use the same WEP encryption method and encryption key, or else your wireless network will not function properly.




Encryption Select a level of WEP encryption,

40/64 bits (10 hex digits) or 104/128 bits (26 hex digits) .

The default is 40/64 bits (10 hex digits) .

Passphrase Enter a Passphrase to automatically generate

WEP keys. Then click Generate .

Key 1-4 If you did not enter a Passphrase, enter the WEP key(s) manually.

TX Key Select which TX (Transmit) Key to use. The default is 1 .

WEP

WEP is a basic encryption method, which is not as secure as WPA.

13

Chapter 3


Wireless MAC Filter

Enabled/Disabled To filter wireless users by MAC Address, either permitting or blocking access, select Enabled . If you do not wish to filter users by MAC Address, keep the default,

Disabled .

Access Restriction

Prevent Select this to block wireless access by MAC

Address. This button is selected by default.

Permit Select this to allow wireless access by MAC

Address. This button is not selected by default.

MAC Address Filter List

Wireless Client List Click this to open the Wireless Client

List screen.

Security Mode > WEP

Encryption Select a level of WEP encryption,

40/64 bits (10 hex digits) or 104/128 bits (26 hex digits) .

The default is 40/64 bits (10 hex digits) .

Passphrase Enter a Passphrase to automatically generate

WEP keys. Then click Generate .

Key 1-4 If you did not enter a Passphrase, enter the WEP key(s) manually.

TX Key Select which TX (Transmit) Key to use. The default is 1 .



Wireless > Wireless MAC Filter

Wireless access can be filtered by using the MAC addresses of the wireless devices transmitting within your network’s radius.

Wireless Client List

Wireless Client List

This screen shows computers and other devices on the wireless network. The list can be sorted by Client

Name, Interface, IP Address, MAC Address, and Status.

Select Save to MAC Address Filter List for any device you want to add to the MAC Address Filter List. Then click Add .

To view the most up-to-date information, click Refresh .

To exit this screen and return to the Wireless MAC Filter screen, click Close .

MAC 01-50 Enter the MAC addresses of the devices whose wireless access you want to block or allow.



Wireless > Advanced Wireless Settings

This Advanced Wireless Settings screen is used to set up the Router’s advanced wireless functions. These settings should only be adjusted by an expert administrator as incorrect settings can reduce wireless performance.

Wireless > Wireless MAC Filter


Chapter 3

Wireless > Advanced Wireless Settings

Advanced Wireless

AP Isolation This isolates all wireless clients and wireless devices on your network from each other. Wireless devices will be able to communicate with the Router but not with each other. To use this function, select Enabled . AP

Isolation is disabled by default.

Authentication Type The Authentication Type setting is available if the Security Mode is RADIUS or WEP. The default is set to Auto , which allows either Open System or Shared Key authentication to be used. With Open

System authentication, the sender and the recipient do

NOT use a WEP key for authentication. With Shared Key authentication, the sender and recipient use a WEP key for authentication. Select Shared Key to only use Shared Key authentication.

Basic Rate The Basic Rate setting is not actually one rate of transmission but a series of rates at which the Router can transmit. (The Basic Rate is not the actual rate of data transmission. If you want to specify the Router’s rate of data transmission, configure the Transmission Rate setting.) The Router will advertise its Basic Rate to the other wireless devices in your network, so they know which rates will be used. The Router will also advertise that it will automatically select the best rate for transmission. The default setting is Default , when the Router can transmit at all standard wireless rates (1-2 Mbps, 5.5 Mbps, 11 Mbps,

18 Mbps, and 24Mbps). Select 1-2Mbps for use with older wireless technology. Select All , when the Router can transmit at all wireless rates.

Transmission Rate The Transmission setting is available if the Network Mode is BG-Mixed, Wireless-G Only, or

Wireless-B Only. The rate of data transmission should be set depending on the speed of your wireless network. Select from a range of transmission speeds, or keep the default,

Auto , to have the Router automatically use the fastest possible data rate and enable the Auto-Fallback feature.

Auto-Fallback will negotiate the best possible connection speed between the Router and a wireless client.



N Transmission Rate The N Transmission setting is available if the Network Mode is Mixed or Wireless-N Only.

The rate of data transmission should be set depending on the speed of your Wireless-N networking. Select from a range of transmission speeds, or keep the default,

Auto , to have the Router automatically use the fastest possible data rate and enable the Auto-Fallback feature.

Auto-Fallback will negotiate the best possible connection speed between the Router and a wireless client.

CTS Protection Mode The Router automatically uses CTS

(Clear-To-Send) Protection Mode when your Wireless-N and

Wireless-G devices are experiencing severe problems and are not able to transmit to the Router in an environment with heavy 802.11b traffic. This option boosts the Router’s ability to catch all Wireless-N and Wireless-G transmissions but severely decreases performance. To use this option, keep the default, Auto . To disable this option, select

Disabled .

Beacon Interval Enter a value between 1 and 65,535 milliseconds. The Beacon Interval value indicates the frequency interval of the beacon. A beacon is a packet broadcast by the Router to synchronize the wireless network. The default is 100 milliseconds.

DTIM Interval This value, between 1 and 255, indicates the interval of the Delivery Traffic Indication Message

(DTIM). A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages. When the Router has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. Its clients hear the beacons and awaken to receive the broadcast and multicast messages. The default value is 1 .

Fragmentation Threshold This value specifies the maximum size for a packet before data is fragmented into multiple packets. If you experience a high packet error rate, you may slightly increase the Fragmentation

Threshold. Setting the Fragmentation Threshold too low may result in poor network performance. Only minor reduction of the default value is recommended. In most cases, it should remain at its default value of 2346 .

RTS Threshold Should you encounter inconsistent data flow, only minor reduction of the default value, 2347 , is recommended. If a network packet is smaller than the preset RTS threshold size, the RTS/CTS mechanism will not be enabled. The Router sends Request to Send (RTS) frames to a particular receiving station and negotiates the sending of a data frame. After receiving an RTS, the wireless station responds with a Clear to Send (CTS) frame to acknowledge the right to begin transmission. The RTS

Threshold value should remain at its default value of

2347 .



15

Chapter 3

Security > Firewall

The Firewall screen is used to configure a firewall that can filter out various types of unwanted traffic on the Router’s local network.

Advanced Configuration sites created using this programming language. Select this feature to enable Java filtering. Deselect the feature to allow Java usage.

ActiveX ActiveX is a programming language for websites.

If you deny ActiveX, you run the risk of not having access to

Internet sites created using this programming language.

Select this feature to enable ActiveX filtering. Deselect the feature to allow ActiveX usage.

Cookies A cookie is data stored on your computer and used by Internet sites when you interact with them. Select this feature to filter cookies. Deselect the feature to allow cookie usage.



Security > VPN Passthrough

The VPN Passthrough screen allows you to enable VPN tunnels using IPSec, PPTP, or L2TP protocols to pass through the Router’s firewall.

Security > Firewall

Firewall

SPI Firewall Protection To use firewall protection, keep the default selection, Enabled . To turn off firewall protection, select Disabled .

Internet Filter

Filter Anonymous Internet Requests This feature makes it more difficult for outside users to work their way into your network. This feature is selected by default.

Deselect the feature to allow anonymous Internet requests.

Filter Multicast Multicasting allows for multiple transmissions to specific recipients at the same time. If multicasting is permitted, then the Router will allow IP multicast packets to be forwarded to the appropriate computers. Select this feature to filter multicasting. This feature is not selected by default.

Filter Internet NAT Redirection This feature uses port forwarding to block access to local servers from local networked computers. Select this feature to filter Internet

NAT redirection. It is not selected by default.

Filter IDENT (Port 113) This feature keeps port 113 from being scanned by devices outside of your local network.

This feature is selected by default. Deselect this feature to disable it.

Web Filter

Proxy Use of WAN proxy servers may compromise the

Gateway’s security. Denying Proxy will disable access to any WAN proxy servers. Select this feature to enable proxy filtering. Deselect the feature to allow proxy access.

Java Java is a programming language for websites. If you deny Java, you run the risk of not having access to Internet


Security > VPN Passthrough

VPN Passthrough

IPSec Passthrough Internet Protocol Security (IPSec) is a suite of protocols used to implement secure exchange of packets at the IP layer. To allow IPSec tunnels to pass through the Router, keep the default, Enabled .

PPTP Passthrough Point-to-Point Tunneling Protocol

(PPTP) allows the Point-to-Point Protocol (PPP) to be tunneled through an IP network. To allow PPTP tunnels to pass through the Router, keep the default, Enabled .

L2TP Passthrough Layer 2 Tunneling Protocol is the method used to enable Point-to-Point sessions via the

Internet on the Layer 2 level. To allow L2TP tunnels to pass through the Router, keep the default, Enabled .



Storage > Disk

Storage > Media Server

16

Chapter 3


Storage > Administration

Access Restrictions > Internet Access

The Internet Access screen allows you to block or allow specific kinds of Internet usage and traffic, such as Internet access, designated services, and websites during specific days and times.

Summary

Status Policies are disabled by default. To enable a policy, select the policy number from the drop-down menu, and select Enabled .

To create a policy, follow steps 1-11. Repeat these steps to create additional policies, one at a time.

1.

2.

3.

4.

Select a number from the menu.

Access Policy drop-down

Enter a Policy Name in the field provided.

To enable this policy, select Enabled .

Click Edit List to select which PCs will be affected by the policy. The List of PCs screen appears. You can select a PC by MAC address or IP address. You can also enter a range of IP addresses if you want this policy to affect a group of PCs. After making your changes, click

Save Settings to apply your changes, or click Cancel

Changes to cancel your changes. Then click Close .

Access Restrictions > Internet Access

Internet Access Policy

Access Policy Access can be managed by a policy. Use the settings on this screen to establish an access policy (after

Save Settings is clicked). Selecting a policy from the dropdown menu will display that policy’s settings. To delete a policy, select that policy’s number and click Delete This

Policy . To view all the policies, click Summary .

Summary

The policies are listed with the following information: No.,

Policy Name, Access, Days, Time, and status (Enabled). To enable a policy, select Enabled . To delete a policy, click

Delete . Click Save Settings to save your changes, or click

Cancel Changes to cancel your changes. To return to the

Internet Access Policy screen, click Close .


List of PCs

5.

6.

Select the appropriate option, Deny or Allow , depending on whether you want to block or allow

Internet access for the PCs you listed on the List of PCs screen.

Decide which days and what times you want this policy to be enforced. Select the individual days during which the policy will be in effect, or select Everyday . Then

17

Chapter 3

7. enter a range of hours and minutes during which the policy will be in effect, or select 24 Hours .

You can block websites with specific URL addresses.

Enter each URL in a separate Website Blocking by URL

Address field.

8.

9.

You can also block websites using specific keywords.

Enter each keyword in a separate Website Blocking by

Keyword field.

You can filter access to various services accessed over the Internet, such as FTP or telnet. (You can block up to three applications per policy.)

From the Applications list, select the application you want to block. Then click the >> button to move it to the Blocked List. To remove an application from the

Blocked List, select it and click the << button.

10. If the application you want to block is not listed or you want to edit a service’s settings, enter the application’s name in the Application Name field. Enter its range in the Port Range fields. Select its protocol from the Protocol drop-down menu. Then click Add .

To modify a service, select it from the

Application list. Change its name, port range, and/or protocol setting. Then click Modify .

To delete a service, select it from the Application list.

Then click Delete .

11. Click Save Settings to save the policy’s settings. To cancel the policy’s settings, click Cancel Changes .

Applications and Gaming > Single Port

Forwarding

The Single Port Forwarding screen allows you to customize port services for common applications on this screen.

When users send these types of requests to your network via the Internet, the Router will forward those requests to the appropriate servers (computers). Before using forwarding, you should assign static IP addresses to the designated servers (use the DHCP Reservation feature on the Basic Setup screen).



Applications and Gaming > Single Port Forwarding

Single Port Forwarding

Common applications are available for the first five entries. Select the appropriate application. Then enter the

IP address of the server that should receive these requests.

Select Enabled to activate this entry.

For additional applications, complete the following fields:

Application Name Enter the name you wish to give the application. Each name can be up to 12 characters.

External Port Enter the external port number used by the server or Internet application. Check with the Internet application documentation for more information.

Internal Port Enter the internal port number used by the server or Internet application. Check with the Internet application documentation for more information.

Protocol Select the protocol(s) used for this application,

TCP , UDP , or Both .

To IP Address For each application, enter the IP address of the PC that should receive the requests. If you assigned a static IP address to the PC, then you can click DHCP

Reservation on the Basic Setup screen to look up its static

IP address.

Enabled For each application, select Enabled to enable port forwarding.



Applications and Gaming > Port Range

Forwarding

The Port Range Forwarding screen allows you to set up public services on your network, such as web servers, ftp servers, e-mail servers, or other specialized Internet applications. (Specialized Internet applications are any applications that use Internet access to perform functions

18

Chapter 3 such as videoconferencing or online gaming. Some Internet applications may not require any forwarding.)

When users send these types of requests to your network via the Internet, the Router will forward those requests to the appropriate servers (computers). Before using forwarding, you should assign static IP addresses to the designated servers (use the DHCP Reservation feature on the Basic Setup screen).

If you need to forward all ports to one computer, click the

DMZ tab.


The Port Range Triggering screen allows the Router to watch outgoing data for specific port numbers. The IP address of the computer that sends the matching data is remembered by the Router, so that when the requested data returns through the Router, the data is pulled back to the proper computer by way of IP address and port mapping rules.

Applications and Gaming > Port Range Forwarding

Port Range Forwarding

To forward a port, enter the information on each line for the criteria required.

Application Name In this field, enter the name you wish to give the application. Each name can be up to 12 characters.

Start~End Port Enter the number or range of port(s) used by the server or Internet applications. Check with the Internet application documentation for more information.

Protocol Select the protocol(s) used for this application,

TCP , UDP , or Both .

To IP Address For each application, enter the IP address of the PC running the specific application. If you assigned a static IP address to the PC, then you can click DHCP

Reservation on the Basic Setup screen to look up its static

IP address.

Enabled Select Enabled to enable port forwarding for the applications you have defined.



Applications & Gaming > Port Range

Triggering


Applications and Gaming > Port Range Triggering

Port Range Triggering

Application Name Enter the application name of the trigger.

Triggered Range For each application, enter the starting and ending port numbers of the triggered port number range. Check with the Internet application documentation for the port number(s) needed.

Forwarded Range For each application, enter the starting and ending port numbers of the forwarded port number range. Check with the Internet application documentation for the port number(s) needed.

Enabled Select Enabled to enable port triggering for the applications you have defined.



Applications and Gaming > DMZ

The DMZ feature allows one network computer to be exposed to the Internet for use of a special-purpose service such as Internet gaming or videoconferencing.

DMZ hosting forwards all the ports at the same time to one PC. The Port Range Forwarding feature is more secure because it only opens the ports you want to have opened, while DMZ hosting opens all the ports of one computer, exposing the computer to the Internet.

19

Chapter 3




Applications and Gaming > QoS

Quality of Service (QoS) ensures better service to high-priority types of network traffic, which may involve demanding, real-time applications, such as videoconferencing.

Applications and Gaming > DMZ

DMZ

Any PC whose port is being forwarded must have its DHCP client function disabled and should have a new static IP address assigned to it because its IP address may change when using the DHCP function.

Enabled/Disabled To disable DMZ hosting, select

Disabled . To expose one PC, select Enabled . Then configure the following settings:

Source IP Address If you want any IP address to be the source, select Any IP Address . If you want to specify an IP address or range of IP addresses as the designated source, select and complete the IP address range fields.

Destination If you want to specify the DMZ host by IP address, select IP Address and enter the IP address in the field provided. If you want to specify the DMZ host by MAC address, select MAC Address and enter the MAC address in the field provided. To retrieve this information, click DHCP Client Table .

DMZ > DHCP Client Table

DHCP Client Table

The DHCP Client Table lists computers and other devices that have been assigned IP addresses by the Router. The list can be sorted by Client Name,

Interface, IP Address, MAC Address, and Expired Time

(how much time is left for the current IP address). To select a DHCP client, click Select . To view the most upto-date information, click Refresh . To exit this screen and return to the DMZ screen, click Close .


Applications and Gaming > QoS

QoS (Quality of Service)

Wireless

You can configure the support and No Acknowledgement settings in this section.

WMM Support If you have other devices that support

Wi-Fi Multimedia (WMM) on your network, keep the default, Enabled . Otherwise, select Disabled .

No Acknowledgement If you want to disable the Router’s

Acknowledgement feature, so the Router will not re-send data if an error occurs, then select Enabled . Otherwise, keep the default, Disabled .

Internet Access Priority

In this section, you can set the bandwidth priority for a variety of applications and devices. There are four levels priority: High, Medium, Normal, or Low. When you set priority, do not set all applications to High, because this will defeat the purpose of allocating the available bandwidth.

If you want to select below normal bandwidth, select Low.

Depending on the application, a few attempts may be needed to set the appropriate bandwidth priority.

Enabled/Disabled To use the QoS policies you have set, keep the default, Enabled . Otherwise, select Disabled .

Category

There are four categories available. Select one of the following: Applications , Online Games , MAC Address ,

20

Chapter 3

Ethernet Port , or Voice Device . Proceed to the instructions for your selection.

Applications

Applications Select the appropriate application. If you select Add a New Application, follow the Add a New

Application instructions.

Priority Select the appropriate priority: High , Medium ,

Normal , or Low .

Click Add to save your changes. Your new entry will appear in the Summary list.

Add a New Application

Add a New Game


QoS > Add a New Game

Enter a Name Enter any name to indicate the name of the entry.

Port Range Enter the port range that the game will be using. You can have up to three ranges to define for this bandwidth allocation. Port numbers can range from 1 to 65535. Check your application’s documentation for details on the service ports used.

Select the protocol TCP or UDP , or select Both .

Priority Select the appropriate priority: High , Medium

(Recommend) , Normal , or Low .


MAC Address

QoS > Add a New Application

Enter a Name Enter any name to indicate the name of the entry.

Port Range Enter the port range that the application will be using. For example, if you want to allocate bandwidth for FTP, you can enter 21-21. If you need services for an application that uses from 1000 to 1250, you enter 1000-

1250 as your settings. You can have up to three ranges to define for this bandwidth allocation. Port numbers can range from 1 to 65535. Check your application’s documentation for details on the service ports used.

Select the protocol TCP or UDP , or select Both .




Online Games

QoS > MAC Address

Enter a Name Enter a name for your device.

MAC Address Enter the MAC address of your device.




Ethernet Port

QoS > Online Games

Games Select the appropriate game. If you select Add a

New Game, follow the Add a New Game instructions.





QoS > Ethernet Port

Ethernet Select the appropriate Ethernet port.




21

Chapter 3

Voice Device


QoS > Voice Device

Enter a Name Enter a name for your voice device.

MAC Address Enter the MAC address of your voice device.

Priority Select the appropriate priority: High

(Recommend) , Medium , Normal , or Low .


Summary

This lists the QoS entries you have created for your applications and devices.

Priority This column displays the bandwidth priority of

High, Medium, Normal, or Low.

Name This column displays the application, device, or port name.

Information This column displays the port range or

MAC address entered for your entry. If a pre-configured application or game was selected, there will be no valid entry shown in this section.

Remove Click this button to remove an entry.

Edit Click this button to make changes.



Administration > Management

The Administration > Management screen allows the network’s administrator to manage specific Router functions for access and security.


Administration > Management

Management

Router Access

To ensure the Router’s security, you will be asked for your password when you access the Router’s web-based utility.

The default is admin .

Router Password Enter a new password for the Router.

Re-enter to confirm Enter the password again to confirm.

Local Management Access

Access via HTTP (HyperText Transport Protocol) is the communications protocol used to connect to servers on the World Wide Web. HTTPS uses SSL (Secured Socket

Layer) to encrypt data transmitted for higher security.

Select HTTP or HTTPS . HTTP is the default.

Access via Wireless If you are using the Router in a public domain where you are giving wireless access to your guests, you can disable wireless access to the Router’s web-based utility. You will only be able to access the utility via a wired connection if you disable the setting. Keep the default, Enabled , to allow wireless access to the utility, or select Disabled to block wireless access to the utility.

Remote Access

Remote Management To permit remote access of the

Router, from outside the local network, select Enabled .

Otherwise, keep the default, Disabled .

Access via HTTP (HyperText Transport Protocol) is the communications protocol used to connect to servers on the World Wide Web. HTTPS uses SSL (Secured Socket

Layer) to encrypt data transmitted for higher security.

Select HTTP or HTTPS . HTTP is the default.

22

Chapter 3

Remote Upgrade If you want to be able to upgrade the

Router remotely, from outside the local network, select

Enabled . (You must have the Remote Management feature enabled as well.) Otherwise, keep the default,

Disabled .

Allowed Remote IP Address If you want to be able to access the Router from any external IP address, select Any

IP Address . If you want to specify an external IP address or range of IP addresses, then select the second option and complete the fields provided.

Remote Management Port Enter the port number that will be open to outside access.

NOTE: When you are in a remote location and wish to manage the Router, enter http://<Internet_IP_address>:port or https://<Internet_IP_address>:por t , depending on whether you use HTTP or HTTPS.

Enter the Router’s specific Internet IP address in place of <Internet_IP_address>, and enter the

Remote Management Port number in place of the word port.

UPnP

Universal Plug and Play (UPnP) allows the appropriate

Windows operating system to automatically configure the

Router for various Internet applications, such as gaming and videoconferencing.

UPnP If you want to use UPnP, keep the default, Enabled .

Otherwise, select Disabled .

Allow Users to Configure Keep the default, Enabled , if you want to be able to make manual changes to the

Router while using the UPnP feature. Otherwise, select

Disabled .

Allow Users to Disable Internet Access Select Enabled , if you want to be able to prohibit any and all Internet connections. Otherwise, keep the default, Disabled .

Backup and Restore

Backup Configurations To back up the Router’s configuration settings, click this button and follow the on-screen instructions.

Restore Configurations To restore the Router’s configuration settings, click this button and follow the onscreen instructions. (You must have previously backed up the Router’s configuration settings.)



Administration > Log



The Router can keep logs of all traffic for your Internet connection.

Administration > Log

Log

Log To disable the Log function, select Disabled . To monitor traffic between the network and the Internet, keep the default, Enabled . With logging enabled, you can choose to view temporary logs.

View Log To view the logs, click View Log .

Log > View Log

Log

• Type Select Incoming Log , Outgoing Log , Security

Log , or DHCP Client Log .

• <Type> Log The Incoming Log displays a temporary log of the source IP addresses and destination port numbers for the incoming Internet traffic. The

Outgoing Log displays a temporary log of the local IP addresses, destination URLs/IP addresses, and service/ port numbers for the outgoing Internet traffic. The

Security log displays the login information for the web-based utility. The DHCP Client Log displays the

LAN DHCP server status information.

Click Save the Log to save this information to a file on your PC’s hard drive. Click Refresh to update the log. Click Clear to clear all the information that is displayed.

23

Chapter 3



Administration > Diagnostics

The diagnostic tests (Ping and Traceroute) allow you to check the connections of your network devices, including connection to the Internet.

Advanced Configuration return to the Diagnostics screen. Click Stop to stop the test.

Diagnostics > Traceroute

Administration > Factory Defaults

The Administration > Factory Defaults screen allows you to restore the Router’s configuration to its factory default settings.

Administration > Diagnostics

Diagnostics

Ping Test

The Ping test checks the status of a connection.

IP or URL Address Enter the address of the PC whose connection you wish to test.

Packet Size Enter the packet size you want to use. The default is 32 bytes.

Times to Ping Enter many times you wish to test it.

Start Test To run the test, click this button. The Ping Test screen shows if the test is successful. Click Close to return to the Diagnostics screen. Click Stop to stop the test.

Diagnostics > Ping

Traceroute Test

The Traceroute test tests the performance of a connection.

IP or URL Address Enter the address of the PC whose connection you wish to test.

Start Test To run the test, click this button. The Traceroute

Test screen shows if the test is successful. Click Close to


Administration > Factory Defaults

NOTE: Do not restore the factory defaults unless you are having difficulties with the Router and have exhausted all other troubleshooting measures. Once the Router is reset, you will have to re-enter all of your configuration settings.

Factory Defaults

Restore All Settings To reset the Router’s settings to the default values, click this button and then follow the on-screen instructions. Any settings you have saved will be lost when the default settings are restored.

Administration > Firmware Upgrade

The Firmware Upgrade screen allows you to upgrade the

Router’s firmware. Do not upgrade the firmware unless you are experiencing problems with the Router or the new firmware has a feature you want to use.

24

Chapter 3

Administration > Firmware Upgrade

NOTE: The Router may lose the settings you have customized. Before you upgrade its firmware, write down all of your custom settings.

After you upgrade its firmware, you will have to re-enter all of your configuration settings.

Firmware Upgrade

Before upgrading the firmware, download the Router’s firmware upgrade file from the Linksys website, www.linksysbycisco.com

. Then extract the file.

Please select a file to upgrade the firmware Click

Browse and select the extracted firmware upgrade file.

Start to Upgrade After you have selected the appropriate file, click this button, and follow the on-screen instructions.

Status > Router

The Router screen displays information about the Router and its current settings.


Router Information

Firmware Version The version number of the Router’s current firmware is displayed.

Firmware Verification The unique identifier that verifies that you have valid firmware is displayed.

Current Time The time set on the Router is displayed.

Internet MAC Address The Router’s MAC Address, as seen by your ISP, is displayed.

Host Name The Host Name of the Router is displayed (if it was entered on the Setup > Basic Setup screen).

Domain Name The Domain Name of the Router is displayed (if it was entered on the Setup > Basic Setup screen).

Internet Connection

This section shows the current network information stored in the Router. The information varies depending on the Internet connection type selected on the Setup > Basic

Setup screen.

Select Release IP Address or Renew IP Address as appropriate to release or renew a DHCP lease.

Click Refresh to update the on-screen information.

Status > Local Network

The Local Network screen displays information about the local, wired network.

Status > Router


Status > Local Network

Local Network

Local MAC Address The MAC address of the Router’s local, wired interface is displayed.

Router IP Address The Router’s IP address, as it appears on your local network, is displayed.

Subnet Mask The Subnet Mask of the Router is displayed.

DHCP Server

25

Chapter 3

DHCP Server The status of the Router’s DHCP server function is displayed.

Start IP Address For the range of IP addresses used by devices on your local network, the starting IP address is displayed.

End IP Address For the range of IP addresses used by devices on your local network, the ending IP address is displayed.

DHCP Clients Table Click this button to view a list of computers or other devices that are using the Router as a DHCP server.


Mode The wireless mode used by the network is displayed.

Network Name (SSID) The name of the wireless network, which is also called the SSID, is displayed.

Channel Width The Channel Width setting (selected on the Wireless > Basic Wireless Settings screen) is displayed.

Wide Channel The Wide Channel setting (selected on the Wireless > Basic Wireless Settings screen) is displayed.

Standard Channel The Standard Channel setting

(selected on the Wireless > Basic Wireless Settings screen) is displayed.

Security The wireless security method used by the Router is displayed.

SSID Broadcast The status of the SSID Broadcast feature is displayed.

DHCP Clients Table

DHCP Client Table

The DHCP Client Table lists computers and other devices that have been assigned IP addresses by the Router.

The list can be sorted by IP Address, MAC Address,

Interface, and Client Name. To remove a DHCP client, click Delete . To view the most up-to-date information, click Refresh . To exit this screen and return to the Local

Network screen, click Close .

Status > Wireless Network

The Wireless Network screen displays information about your wireless network.

Status > Wireless

Wireless Network

MAC Address The MAC address of the Router’s local, wireless interface is displayed.


Appendix A

Appendix A:

Troubleshooting

Your computer cannot connect to the Internet.

Follow these instructions until your computer can connect to the Internet:

•

•

•

Make sure that the Router is powered on. The Power

LED should be green and not flashing.

If the Power LED is flashing, then power off all of your network devices, including the modem, Router, and computers. Then power on each device in the following order:

1. Cable or DSL modem

2. Router

3. Computer

Check the cable connections. The computer should be connected to one of the ports numbered 1-4 on the Router, and the modem must be connected to the

Internet port on the Router.

The modem does not have an Ethernet port.

The modem is a dial-up modem for traditional dial-up service. To use the Router, you need a cable/DSL modem and high-speed Internet connection.

You cannot use the DSL service to connect manually to the Internet.

After you have installed the Router, it will automatically connect to your Internet Service Provider (ISP), so you no longer need to connect manually.

The DSL telephone line does not fit into the Router’s

Internet port.

The Router does not replace your modem. You still need your DSL modem in order to use the Router. Connect the telephone line to the DSL modem, and then insert the setup CD into your computer. Click Setup and follow the on-screen instructions.

When you double-click the web browser, you are prompted for a username and password. If you want to get rid of the prompt, follow these instructions.

1.

2.

3.

Launch the web browser and perform the following steps

(these steps are specific to Internet Explorer but are similar for other browsers):

Select Tools > Internet Options .

Click the Connections tab.

Select Never dial a connection .


Troubleshooting

4. Click OK .

The Router does not have a coaxial port for the cable connection.

The Router does not replace your modem. You still need your cable modem in order to use the Router. Connect your cable connection to the cable modem, and then insert the setup CD into your computer. Click Setup and follow the on-screen instructions.

The computer cannot connect wirelessly to the network.

Make sure the wireless network name or SSID is the same on both the computer and the Router. If you have enabled wireless security, then make sure the same security method and key are used by both the computer and the

Router.

You need to modify the settings on the Router.

Open the web browser (for example, Internet Explorer or

Firefox), and enter the Router’s IP address in the address field (the default IP address is 192.168.1.1

). When prompted, enter the password to the Router (the default is admin ). Click the appropriate tab to change the settings.

In Windows XP, you do not see the Router on the My

Network Places screen.

In the Network Tasks section, click Show icons for networked UPnP devices . If the Router does not appear, follow these instructions:

1.

2.

3.

4.

Go to Start > Control Panel > Firewall .

Click the Exceptions tab.

Select UPnP Framework .

Click OK .

In Windows XP, you do not see your USB storage device on the View workgroup computers screen.

Make sure the Router and your computer use the same workgroup name. (The default workgroup name of the

Router is linksys . In Windows XP, go to Start > Control

Panel > System . Click the Computer Name tab. The workgroup name is displayed.) If they differ, then change the workgroup name of the Router. Follow these instructions:

2.

3.

4.

1.

5.

Access the web-based utility of the Router. (Refer to

Chapter 3: Advanced Configuration , page 4

.)

Click the Storage tab.

Click the Administration tab.

In the Workgroup field, enter the workgroup name of your computer.

Click Save Settings .

27

Appendix A

WEB: If your questions are not addressed here, refer to the Linksys website, www.linksysbycisco.com

Troubleshooting


Appendix B

Appendix B: How to Install and Access USB Storage

Overview

This appendix explains how to connect, access, and map a shortcut to an external USB storage device.

Install the USB Storage Device

1.

2.

Make sure your computer has a wired or wireless connection to the Router.

Connect an external USB hard disk drive or USB flash disk to the USB port of the Router.

Access the USB Storage Device

Follow the instructions for your Windows operating system, Vista or XP.

Windows Vista

1. On your desktop, double-click the Computer icon.

Computer Icon

2. In the

Router:

Address field, enter the server name of the

\\<server_name_of_Router>

Enter Server Name of Router

The default server name of the Router is WRT160NL . You can change this name on the Storage > Administration

screen; refer to Storage > Administration , page 17

.

NOTE: Another option is to use the IP address of the Router. In the Address field, enter the local

IP address of the Router:

\\<local_IP_address_of_Router>

The default is 192.168.1.1

. You can change this

IP address on the Setup > Basic Setup screen;

refer to Setup > Basic Setup , page 4

.

How to Install and Access USB Storage

3. On the login screen, enter your account user name and password. (For the admin acccount, admin is both the default user name and password.)

Enter Account User Name and Password

User accounts are set up on the Storage > Administration screen; refer to

Storage > Administration , page 17

.

Windows XP

1. On your desktop, double-click the icon.

My Computer

My Computer Icon

2. In the

Router:




The default server name of the Router is WRT160NL . You can change this name on the Storage > Administration screen; refer to

Storage > Administration , page 17

.



\\<local_IP_address_of_Router> (The default is 192.168.1.1

. You can change this IP address on the Setup > Basic Setup

screen; refer to Setup

> Basic Setup , page 4

.)


Appendix B

3. Enter your account user name and password. (For the admin acccount, admin is both the default user name and password.)

How to Install and Access USB Storage

3. Right-click the folder you want to share, and click Map

Network Drive . (The default shared folder is named

Public .)

Enter Account User Name and Password

User accounts are set up on the Storage > Administration


.

Create a Shortcut to a Shared Folder

You can map any folder of the USB storage device as a separate drive. Follow the instructions for your Windows operating system, Vista or XP.

Windows Vista

Map a Drive

1. On your desktop, double-click the Network icon.

Map Network Drive

4. From the Drive drop-down menu, select an available drive letter.

Network Icon

2. In the

Router:




The default server name of the Router is WRT160NL . You can change this name on the Storage > Administration


.



\\<local_IP_address_of_Router>

The default is 192.168.1.1

. You can change this

IP address on the Setup > Basic Setup screen;

refer to Setup > Basic Setup , page 4

.


Select Drive Letter

5. Click Finish .

Access Mapped Drive

1.

2.

On your desktop, double-click the Computer icon.

Double-click the mapped drive to access it.

Double-Click Mapped Drive

30

No results