Mobile Communications S4RBRM22050 ConsumerWideband Bi-Directional Booster User Manual

User Manual & Instructions

Series: BRM22050

For use with:

2G, 3G & 4G Cellular Devices

The BRM220-50 Dual Band RX/TX 800/1900Mhz

Signal Booster with Smoothtalker proprietary

" Stealthtech Signal Technology "

Increases your Cellular and PCS Band Signals, expands your service coverage area, enhances voice call quality and significantly increases

Data speeds

The Intelligent CPU monitors the environment in which the amplifier is operating and continuously adjusts itself to prevent Oscillation and also automatically prevents any RX/TX overload to both the Cell Phone and Cellular Tower while giving you maximum signal improvement. It is easy and simple to install and you can be up and running in minutes

This is a CONSUMER device

BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider's consent.

Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider.

You MUST operate this device with approved antennas and cables as specified by the manufacturer.

Antennas MUST be installed at least 20 cm (8 inches) from any person.

You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider.

WARNING. E911 locator information may not be provided or may be inaccurate for calls served by using this device.

Initial Setup Assembly & Installation

1-First make sure that no power is connected to the booster. Connect the inside antenna, the outside antenna and power supply to the booster. Please make sure to connect each item in to the correct ports as indicated on the booster.

2-Place the antenna on the outside of the vehicle or building and keep it separated as far as possible from the inside antenna or cell phone holder.

3-Turn the power switch to ON position and the single Green LED on the side of the unit will become Green, constant ON, to indicate that power is reaching the booster and that it is turned on.

Operation: PLEASE NOTE: It is normal for the booster to be quite warm during cell phone "in use" state.

LED Light Indicators on

Panel Label:

Orange LED Lights (RX):

There two orange LED lights, one for the 800MHz cellular band and one for the 1900MHz PCS band. LED

ON state indicates that the RX (Receive Signal) function of the band is functioning normally.

LED Off state indicates that the band is shut down.

Green LED Lights (TX):

There two Green LED lights, one for the 800MHz cellular band and one for the 1900MHz PCS band.

Solid ON state indicates that the TX (Transmit Signal) function of the indicated band is on and is at maximum gain.

Flashing Green LED in either 800MHz or 1900MHz indicates gain reduction in that band

Each flash equals 3db reduction in gain. One flash represents a 3dB reduction, two flashes represents a

6dB reduction etc. until the total gain of the booster has been suppressed.

Causes of Flashing Green LED Lights:

1-If the outside antenna is located too close to the inside antenna or phone holder the booster will reduce gain in order to suppress any oscillation (feedback loop) and the Green LED will flash. To achieve higher gain or max gain further separation of the inside and outside antennas is required.

2-If the booster is close to a cellular tower (Strong cell tower signal ) it will automatically reduce its gain to protect the network. This condition will change as the booster approaches or leaves a cellular tower. This is normal and cannot be defeated or altered by the user.

All parts shown may or may not be included depending on the

Smothtalker Booster Kit part number configuration

Signal Booster

InsideAntenna

Outside Antenna

DCH6i: DC 6V Power

Supply; Install type

DCH6HV: AC/DC Wall

6V Power supply

DCH6Csw: DC 6V Power Cigar

Socket type Adapter

Pg. 2

Pg. 3

To comply with FCC rules, this booster must only be operated with cables, antennas and coupling devices that have been approved for use with this equipment

For specifications of any of the Smoothalker FCC approved part numbers listed below visit smoothtalker.com

Authorized Magnetic base Antennas

SEM244MMF

SEM2MX, SEM2MF

SEM11MX, SEM11MF

SEM15MX, SEM15MF

SEM2MaX, SEM2MaF

SEM11MaX, SEM11MaF

SEM15MaX, SEM15MaF

SEM2MaXL, SEM2MaFL

SEM11MaXL, SEM11MaFL

SEM15MaXL, SEM15MaFL

SEM2LGMX, SEM2LGMF

SEM11LGMX, SEM11LGMF

SEM15LGMX, SEM15LGMF

SEM26LGMX, SEM26LGMF

SEM2LGMXL, SEM2LGMFL

SEM11LGMXL, SEM11LGMFL

SEM15LGMXL, SEM15LGMFL

SEM26LGMXL, SEM26LGMFL

Authorized thru-hole Antennas

SEM2THX, SEM2THF

SEM11THX, SEM11THF

SEM15THX, SEM15THF

SEM26THX, SEM26THF

SEM2THXL, SEM2THFL

SEM11THXL, SEM11THFL

SEM15THXL, SEM15THFL

SEM26THXL, SEM26THFL

Authorized Inside antennas

SEMR P1X

SEMR P1XL

SEMR1

Authorized Co-ax Cables

ACX100 extension cable

ACX900 extension cable

AC series antenna connection

Authorized directional Antennas

SEMD1XL, SEMD1FL

SEMDA2XL, SEMDA2FL

Important:

1-Use only the power supply included with the booster. Connecting any other power supply at any time will result in damage to the booster and will void the warranty.

2-Do not turn on the power switch until ALL cables have been screwed or plugged into the booster or you can cause damage to the booster.

3-It is the user's/operator's responsibility to maintain a minimum distance of 8 inches separation from the antennas to any person.

Notes:

1-This booster is not user configurable. User changes are a violation under FCC rules and will void the user's authority to operate the equipment.

2-User changes changes or modifications will void warranty.

Warranty: 2 Year on manufacturing defects.

Does not include misuse or customer damage.

Original Bill of Sale is required for all Warranty Claims

Contact us at: smoothtalker.com

Pg. 4