NE }tx 1
·
S O L U T I O N S
Introduction
Thank you for purchasing the new Kronos300
Universal range extender from Nexxt Solutions™.
If any of the follow i ng items are m i smatched, m i ss i ng or damaged, please contact the merchant from whom you purchased the unit for i mmediate replacement.
• Universal range extender
• Network cable
• Quick i nstallation guide
Product layout
1 --o
.
N£ Ja!"
l-- - 4
Component
1
Range extender
button (WPS)
Description
Enables the un i ve:rsal repeater mode on the device
2
LAN port
3
RESET button
4
Wall plug
Fo r con n ection to a computer, router or switch in your network.
Press this button for over 7 seconds t.o r estore the dev i ce to its f ac t ory default sett i ngs .
Conveniently designed to be plugged into any standard electr i cal outlet
LED indicators description
The LED indicators prov i de information about network activ i ty, the connection and link status in real time.
They also facilitate activity monitoring and troubleshooting the performance of the device.
LED Status Description
Power
Range
extender
(RE)
.
~r~
(Signal
Strength)
LAN
So l id
So l id
~
Blinkinn
Off
The device i s properly connected to the power supp l y
Bridged successfully
-
Nenotiatinn ke\I
Not bridged
So l id
Off
Strong signal
Solid orange Weak s i gna l
Not bridged
So l id
Proper c onnection is est.abl
i s h ed o n the LAN port
Blinking Data is being transm i tted through the LAN port
Preliminary steps
Before you begin, follow the recommendations listed below:
•Verify that your Ethernet network i s set up .
•Verify that your Internet connect i on is working
•Avoid connecting other devices into the same wall outlet as the repeater.
•Avoid using a power strip or a surge protector, s i nce i t may adversely affect the performance of this product.
Hardware installation
1. Plug the extender into an electr i c outlet that is close to the wireless router or access po i nt whose signal you intend to boost .
Note: Proximity to the main wireless router/access point is only requ i red during the initial setup process.
2. You have the choice of connecting wireless l y or you may connect your PC to the sing l e LAN port of the extender us i ng the supp l ied Ethernet cable.
3. Both setup methods are described below.
Configuration methods
There are two configuration methods supported by t h e repeater : The first method is the i nstant configuration through the extender button. The second one is the web based configuration method which is accomplished using your internet browser .
(<·
¢' ·
0
(re
D rr, D
Instant push-button setup
Note:
As the latest WPS 2.0 specification only supports
WPA2 protocol, first you must make sure that the wire l ess router or access point you are using has this feature available and enabled.
One of the functions of the extender is to act as a br i dge between a Wi-Fi router and a wireless device outside the router's range, by incorporating i t to a wire l ess network that is up and running.
This is a very convenient and user-friend l y procedure that we strongly recommend. To do this, simply follow the few easy steps described below. Device configuration with wired and wireless clients
1. Press the range extender's button on the front of the device for about 1 to 3 seconds.
2. The RE LED blinks while the extender attempts to add a wireless client (a computer or other device) to its wireless network.
(<·
0
3. Within two minutes , press the WPS or QSS button on your router, or follow the WPS instructions that came with your wire l ess device.
4. When the RE LED g l ows solid green, it means that the wireless range extender has connected to the desired router or access po i nt successful l y.
·>) (<·
0
5. You can also login to the web management interface to check bridge status.
Web-user interface
This w i red setup requires the execution of the web-based configuration procedure. as described be l ow:
1. First, connect your computer to the extender with the supplied Ethernet cable.
2. Plug the extender into an electrical outlet.
IMPORTANT: Do not use the Ethernet cable to connect the extender to a router. If you do so , the extender will not work, since it is designed to only allow a wireless connection to the router.
3. On your computer, launch the web browser.
On the address bar, type our site address re.nexxtsolutions.com, followed by enter .
4 . In this stage, the wireless repeater web interface will come up . The system will prompt you to enter the defau l t password : admin . Then, click Ok to continue.
-=-
~-
5.
The Range extender setup window will be displayed.
C l ick on Open scan to detect the w i re l ess device broadcasting the s i gnal you want to extend.
6.
Locate and select the desired remote router or access point from the list .
..
-
~· -,
.
.
..
.
-·
.
~ .
.
--· • M •
~ ~ · · -
• · -
::. :: u •••· "
~ :::: : . :
~ ~~ ~
•
.
-~
~ -
·-
U> ~
~
-
··
0
.
· ~ -
·· ·
•
-
M
7.
When the following window appears, click OK to confirm the selected device on the previous step.
T h e p a g e a t 1 92 .
1 6 3 .
0 .
2 54 s a ys:
P l e as e d ic k O K t o c o n fi rm 1 0 c o n n e ct ~ o ~ e l e c t e d A P I
O K 1 1 c ~ n ce l x
8. Enter the remote device's password in the Security
Key field . Verify that the channel, security mode and algorithm match the device's settngs. C l ick Save
when done.
-· ~ · -
·
-
· ~
-
·
-
·--
-
~
-
·-~
·«· •-·
9 . The extender will automatically reboot to enable the new configuration to take effect in the system.
1 D. Once it finishes rebooting , you can enjoy instant internet access with the new extender using a wireless or wired connection
Position your range extender
After the initia l setup process has been completed, you may re l ocate the extender in a spot that allows optimum wireless coverage and performance to be achieved.
•The ideal locat i on is to place the extender half-way between your wireless router and your Wi-Fi enabled devices, as illustrated below.
>)
(c·
((c D
Smartphone
Tabl e t
• Bear in mind that the best connection is established when there is a c l ear line of sight between the extender and the wireless router. and between the extender and the active c l ients on the network.
•Try to posit i on the extender away from electrical devices that are potential sources of interference , such as ceiling fans, home security systems, microwaves, computers, refrigerators, or cordless phones.
•The extender signal strength LED can help you determine at what point the best performance is being achieved.
•Even though the usual connection to the extender is wireless, you can use its LAN port to connect a wired device, such as an Ethernet enab l ed gaming console, pr i nter or PC.
FCC statement
This device compl i es with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2] this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the l i mits for a Class B d i gital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection aga i nst harmful interfer ence in a residential installation. This equipment generates, uses and can radiate rad i o frequency energy and, if not installed and used in accordance w i th the instructions, may cause harmful interference to radio commun i cations. However, there is no guarantee that interference will not occur in a particular instal l at i on . If th i s equipment does cause harmful interference to radio or television reception, which can be determ i ned by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures :
•Reor i ent or relocate the receiving antenna.
•Increase the separation between the equipment and rece i ver.
•Connect the equipment into an outlet on a c i rcuit different from that to wh i ch the receiver i s connected.
•Consult the dealer or an experienced radio/TV technician for help.
FCCID: X4YKRNS3V2
FCC caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co~ocated or operating in conjunct i on with any other antenna or transmitter.
The manufacturer is not responsible for any radio or
TV interference caused by unauthorized modifications to this equipment .
Radiation Exposure Statement
This equipment complies w i th FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
