Nexxt Xpy 1200, Xpy 1230 Wireless IP camera Quick Installation Guide

NE XAT
SOLUTIONS
NEXXT
S OLUTIONS
1200/ 1230
IP CAMERA
AIWELFI4U 1/AIWPTFI4U2
Nexxt Solutions - Xpy1200/Xpy1230 Wireless IP camera Nexxt Solutions - Xpy1200/Xpy1230 Wireless IP camera
Quick Installation Guide e Quick installation guide
| | nn | e Resource CD-ROM, containing the following:
Thank you for purchasing the High Definition Wireless IP
camera from Nexxt Solutions. This easy to set up indoor - XpyGuard PC client software
camera is a versatile security option for viewing, recording, - XpyGuard mobile app
and archiving footage. This document will guide you through - IP camera search tool
the installation process of the camera, including its hardware - Digital copies of the quick installation guide
and software configuration based on the available - IPCWebComponents web plug-in
operation and viewing platforms. Product overview
Package contents Xpy 1200
Open the box and make sure all items listed below are Front panel Back panel
included: 4
Xpy 1200
e Wireless fixed IP camera
e AC power adaptor
e Network cable
e Mounting hardware
e Self-adhesive rubber pads for desktop mounting
e Quick installation guide
e Resource CD-ROM, containing the following:
- XpyGuard PC client software
- XpyGuard mobile app
- IP camera search tool
- Digital copies of the quick installation guide
(
1. Built-in wireless antenna 9, Reset
- IPCWebComponents web plug-in 2. Built-in microphone 10. WPS button
Xpy 1230 3. Light sensor 11, Power indicator light (green)
4, Night vision LEDs 12. Wireless indicator light (green)
e Wireless pan and tilt IP camera 5. Lens 13. Speaker
e AC power adaptor 6. Network port (RJ45) 14. Mounting base with
e Network cable 7. DC input articulating arm
e Mounting hardware and bracket 8. Heat sink
e Wireless antenna
1 2
Nexxt Solutions - Xpy1200/Xpy1230 Wireless IP camera
Xpy 1230
Front panel
(
\
Back panel
f
Bottom view г
. Light sensor
. Night vision LEDs
Lens
. Built-in microphone
. Speakers
. Heat sink
. DC input
. Network port (RJ45)
ONDUIPRwWMm-
. Wireless indicator light (green)
. Power indicator light (red)
. SD card slot
. Wireless antenna jack
. WPS button
. Audio output
. Audio input
. Threaded mounting socket
. Reset button
Nexxt Solutions - Xpy1200/Xpy1230 Wireless IP camera
Basic setup
Connection of the IP camera to a router
e Begin by attaching the mounting bracket and the antenna
(if applicable) to the device.
e Select the mounting location for the camera, either on a wall,
ceiling, or on a desktop.
e Insert the Ethernet cable to the RJ45 port of the IP camera.
e Connect the other end of the network cable to your Ethernet
switch, hub, router or IP sharing device.
e Plug the camera to a wall outlet using the supplied AC
adaptor to power it on.
4 à
| | |
Internet connection
O “e :
Modem
Computer Cellular PDA
Phone
|
Intranet
|
IP Camera
Warning: Make sure to use the supplied power adapter to
make the connections to the AC mains. The use of a different
adaptor may cause damage to the camera, heat up or catch
fire. Any damage caused to the camera by using the incorrect
power adaptor will void the warranty.
Verify that the mains voltage (110V or 220V) and frequency
(SOHz ог GOHZ) of your location match those specified on
the label.
Nexxt Solutions - Xpy1200/Xpy1230 Wireless IP camera
Software installation
1. First insert the installation CD-ROM disk in your CD drive.
2.Locate the folder IP camera search tool and then look for the
subfolder containing the operating platform of your computer:
For Windows OS or For Mac OS.
À
ARTE
азы
Shortcut icon for Windows OS Shortcut icon for Mac OS
3. Copy and paste the IP camera tool file to your computer,
or simply drag it onto your desktop.
Note:
If your computer does not have a CD drive, you can download
the IP camera tool directly from our website for free.
Accessing the camera
1.Enable the DHCP feature of your router (which is normally
set to this protocol by default).
Proceed to open the IP Camera tool, which is designed to
find the camera's IP address automatically in your LAN
(Local Area Network).
2. Double click the IP address of the camera from the list.
This will cause your default browser to open the camera's
login page.
3.When logging in for the first time, you will need to download
and install the IPC WebComponenrts. We will use Internet
Explorer in this example. However, for browsers like Google
Chrome, MAC OS, Safari or Mozilla Firefox, please refer to
the user manual.
5
Nexxt Solutions - Xpy1200/Xpy1230 Wireless IP camera
Note:
The 64-bit browser is not supported.
Axt
©_ 2 zz = A-G | LS IPCam Client ad
El View Favori р
МЕХХТ HDIP.Camera
Internet Explorer - Security Wannin x]
The publisher could not be verified. Are you sure you want to install this
software?
Name: IPCWebComponents.exe
Publisher: Unknown Publisher
| Install | | Dontinstall |
| 4 This file does not have a valid digital signature that verifies its publisher, You
should only install software from publishers: you trust. How can I deade what
software to install?
4, After installing the IPC VWebComponents, refresh the browser.
The login window will come up on the screen. The user will
be then prompted to input the camera credentials. Type
admin for the user name and leave the password field blank.
Click Login to continue.
Note: Should the installation of the plug-in fail, you may
install it directly from the CD or download it from our Nexxt
solutions’ website.
Nexxt Solutions - Xpy1200/Xpy1230 Wireless IP camera Nexxt Solutions - Xpy1200/Xpy1230 Wireless IP camera
Note:
Username admin | If you forget your username or password, you can press and
hold the reset button of the camera using a pin for five
seconds. This resets the device to its factory default values.
Password |
Stream [Main stream
6. After concluding the initial login phase into the camera,
the system will direct you automatically to the Setup Wizard
interface. This is designed to assist you in configuring the
basic parameters of the camera, such as name, time, IP
address, and wireless settings.
Language |English
Note: Camera web interface
The camera supports two stream modes: Main stream is the Once the camera configuration has been successfully
option offering the best quality video. Sub-stream video is lower completed, the main monitoring page will be displayed after
in terms of quality, but image streaming Is delivered at a logging in, as shown below.
faster rate. Main surveillance window
о. When setting up your camera for the first time, it will 4 à
request that you modify the default username and/or
password if both are still set to default. Enter the new
username, new password and confirm the password.
Click on Modify to save the changes. The new username
and password will be the credentials that you will need to
enter when logging in to the camera in the future.
Co) (DG En © EI (4) GD)
—
(e)
Username (admin
New username |
\
New password | |
1.Top menu bar: Located on the upper edge of the screen,
it contains the main navigational tabs that give access to
Confirm the password | | the following functions of the device:
Password Security Level
Opens the main monitoring window and displays
footage captured by the camera in real time.
7 8
Nexxt Solutions - Xpy1200/Xpy1230 Wireless IP camera Nexxt Solutions - Xpy1200/Xpy1230 Wireless IP camera
O a Opens the Administrator control panel, for access
to all the parameters, menus and advanced
settings avallable in the device.
Wireless connection
lf the user wants to access the camera using a wireless
connection or the Internet, the Wireless and Remote Access
configuration must be completed. To do so, follow the steps
e 4 Opens the playback panel to reproduce recorded
Auch y described in this section of the user guide.
video files stored directly in the SD card. (Available
in the Xpy1230 only).
2. Display control panel: the firmware supports the selection
of single view, and also the split view in four and nine
frames, so as to monitor multiple channels at the same
WPS (Wi-Fi Protected Setup)
Note: the WPS function is recommended to perform the
wireless connection setup.
time 1.Press and hold the WPS button on the camera for two
3. Operating mode: selectable video format of 50Hz, 60Hz seconds.
or outdoor. Е >
4. Stream type: selectable resolution settings based on the
connection type, avallable bandwidth and the video format cil
used. a WPS button |
5. Mirror/Flip: generates a mirror image or changes the [ wes button | LEE
frame orientation vertically or horizontally
6. Directional buttons: use these buttons to move the \ }
camera up, down, left and right. The center button will
cause the camera to move back to its center position.
(Available in the Xpy1230 only).
7/.Cruise control: selects the vertical or horizontal trajectory
2, Within 60 seconds, press the WPS button on your router.
This is usually found on the back or on the side of the router.
Some devices may even require to log in to their web interfa-
of the camera (Available in the Xpy1230 only).
8.Preset positions: use this feature to define different
scanning patterns for the camera. A maximum of 16
preset positions can be stored. (Available in the Xpy1 230
only).
9.1А LED lights: it provides the manual, automatic or
scheduled activation of the LED lights.
10. Color adjustment: this menu provides image setting
parameters, such as hue, brightness, saturation and
sharpness.
11.Bottom menu bar: it contains the shortcut icons for Play,
Stop, Talk, Audio, Snapshot, Record and Full screen.
9
ce, and click on an on-screen button to activate the WPS
feature. If you are not sure where the WPS button is located
on your router, please refer to the manufacturer's manual
for details.
‚ The camera will automatically create a secure wireless
connection to your router in about 60 seconds. If a network
cable has been previously connected, make sure to remove
it now,
10
Nexxt Solutions - Xpy1200/Xpy1230 Wireless IP camera
Note
Set the security mode of your router to
WPA-PSK/WPAe2-PSK. Otherwise, the WPS settings may
fail to take effect.
. № your wireless router does not support the WPS function,
open the Settings tab on the top of the camera main
page, then go to the Network - Wireless settings section
on the left side of the screen. Click Scan to continue.
AL Setup Wizard ) N
Wireless Settings
Status
Basic Setlings
Wireless Network List Scan Ban [|]
SSID{Network Name) Encryption Quality Encryption [None w|
ACT50_2.4GHz WPA2
il
= и О PRA ANOTA!
Nexxt_Solaris300 WPAZ
Nevoct_Window WPA
yellow WPA?
Blue WPA
y
‚Select the SSID (name of your router) from the list, and
the corresponding network identifier and encryption will be
automatically filled on the right side of the page. All you
need to do is to enter the password assigned to your
wireless network.
Wireless Settings à
G= Save) E Refresh) \
Wireless Network List Scan | = BEE ZIEH
SSID(Network Name) Encryption | Quality | aan QU Y]
== am Te Password [escsssose
ACTSO 246H | | РА | = | The maximum password length is 63,
E : г те wall a including numbers, letters and symbols ~! @
Nexxt_Solaris300 A2 DE de
Nexxt_Window WPA u
yellow WPA2 A
` Blue WPA2 Lo ED
11
Nexxt Solutions - Xpy1200/Xpy1230 Wireless IP camera
6. Click the Save button and disconnect the network cable.
Keep the camera powered on until it is displayed on the IP
Camera tool. If the camera does not show up on the screen,
unplug the power cable from the camera and then plug it
back in again. The connection to the wireless network should
happen automatically.
Remote access
If you want to access your camera via a web browser outside
of your network, please configure the following parameters
as indicated below.
1.Ореп the Settings tab on the top of the camera main page,
then go to the Network - IP configuration section on the left
side of the screen. Once there, uncheck the Obtain IP DHCP
option. Ensure that the Secondary DNS Server is set to
8.8.8.8.
( à
Setup Wizard à Е
= = ) IP Configuration
Basic Settings E save ) (Со Refresh) |
Obtain IP From DHCP]
IP Address 192.168.1.100 |
en 2892992590 | IP Address: Set this in the same
Gateway 192.168.1.1 subnet as your computer, or keep
Primary DNS Server 211162781 | it as default.
Secondary DNS Sere 211.162783 | 2Ubnet Mask: Keep it as default.
Gateway and DNS Server: Set it to
the IP address of your router.
N „ D
2, Enable UPnP and DDNS on the camera's Network settings
page. We recommend selecting the factory's default DDNS.
( Siatu N
IL BasiSettings
UPnP
ES Rs)
[= Dis
| Enable UPNP | | Yes} [=] |
A A
[Select Yes and click Save. ]
12
Nexxt Solutions - Xpy1200/Xpy1230 Wireless IP camera
Status )
? —— DDNS
Basic Settings J = —
— < ave (>. Refresh )
Network J —
u Enable DDNS |
Manufacturer's DONS
| Manufacturers DDN: | | ba0763.myipcamera.org | | [Restore DDNS to factory
1 1
Domain
Third Party DDNS Click Enable DDNS and click Save.
| DDNS Server ri The content in the Manufacture’s DDNS
[column is the domain name of your camera
3. Click on the Port option under the Network settings. You
can set the port of your camera here. If you want to enable
the Remote access feature for multiple cameras in the
network, you will need to change the HTTP port of each
individual device.
| Status w)
Basic Setting 2)
Network )
Port
a js) Refresh ) |
HTTP Port 38
HTTPS Port 443
ONVIF Por 838
Д.Е UPnP has been enabled in the router, you do not need to
perform the following steps. However, if UPnP is disabled,
you will need to select one of the following methods to
configure the port forwarding function on your router.
A. lf the UPnP function is available in your router, find the
forwarding menu and make sure the UPnP option is
enabled.
B. If there is no UPnP function in your router, the port
(HTTP port) forwarding feature needs to be manually
enabled through the forwarding and virtual server
menus.
13
Nexxt Solutions - Xpy1200/Xpy1230 Wireless IP camera
9. Now you can access your IP camera using the domain name
address and port number with a colon in between, using the
Internet. For example: https: //abc123.myipcamera.org:88.
Remote access using a mobile device
The IP camera provides a smartphone app for Android and
10$ users, to remotely view live footage on your mobile
device. If you use a mobile device that operates оп an 105 or
Android platform, you can use the free App to access the
camera through the LAN or Internet.
Since both apps are similar, we have chosen the Android
system to illustrate the configuration procedure in this guide.
1. First, search and install the XpyGuard application from
Google Play or the App Store, depending on your devices
platform.
2. After verifying that the mobile phone and the camera are
connected to the same wireless router, run the app and
proceed to open the XpyGuard management page.
3. Select the Tap + to add camera option.
My Cameras: @)
o 2
About
14
Nexxt Solutions - Xpy1200/Xpy1230 Wireless IP camera Nexxt Solutions - Xpy1200/Xpy1230 Wireless IP camera
4. lap on the QR UID tab and select the search GR code 6. Enter the Username and Password of your camera, and click
button. CONNECT to move on to the following step.
E Add New Camera
< Add New Camera
QR UID DDNS IP Address
Е] QR Code UID
all |
CHMSAWC6M92VUHPMY7GJ
If there is ОВ code on your camera, please tap the , г
button above to scan the QR code to add your Please input username and password of your
camera; otherwise please use DDNS or IP Address camera.
tab instead.
Nexxt
If it is not possible to scan the OR code, you can
input OR code UID here manually.
| Display Password
QR Code UID
Next
CONNECT
5. Next, scan the QR code located on the bottom label of the - . . .
; | 7.Select Skip the Wi-Fi settings, if your wireless connection
camera. The QR code UID field should be populated with | |
the same code found on the camera label. Click Next to was previously setup. Otherwise, you will need to complete
continue | this procedure by clicking the wireless signal button on the
| app to search for the available Wi-Fi networks.
< Add New Camera
QR UID DDNS IP Address X Setup a Wi-Fi connection
tre Make sure your smartphone/tablet is near
= the camera, tap the button below to search
Wi-Fi networks.
If there is OR cade on your camera, please tap the
button above to scan the OR code to add your ———
camera; otherwise please use DDNS or IP Address is
tab instead. Ge)
If itis not possible to scan the QR code, you can El
р : Please connect to Wi-Fi network.
input GR code UID here manually.
Wi-Fi SSID
Please input the Wi-Fi password
(Display Password
OR Code VID
CHM9AWCEM92VUHPMY7GJ
Please Note: After pressing the Next button,
unplug the network cable on the camera.
CONNECT
15 16
Nexxt Solutions - Xpy1200/Xpy1230 Wireless IP camera Nexxt Solutions - Xpy1200/Xpy1230 Wireless IP camera
8. Опсе the camera appears listed on the My Cameras/ FCC statement
Home screen, select it to allow the connection and start
enjoying live video using your mobile phone. This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
My Cameras
(F Xpy1200 Es
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
ÓN protection against harmful interference in a residential installa-
QT) tion. This equipment generates, uses and can radiate radio
frequency energy ana, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
Q e communications. However, there is no guarantee that interfe-
| AN > | | rence will not occur in a particular installation. If this equip-
9. The app is defaulted to use a Wi-Fi connection on your mobile ment does cause harmful interference to radio or television
device to avoid exceeding your carrier mobile data usage. reception, which can be determined by turning the equipment
If you decide to use your phones 3G/4G data connection off and on, the user is encouraged to try to correct the
instead, you can disable it by going to About-App settings interference by one of the following measures:
and turning off the Only connect using a Wi-Fi connection
option on the mobile app. - Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
< App Settings ircuit di
S Aa - Connect the equipment into an outlet on a circuit different
only connect using Wet connection (X) from that to which the receiver is connected.
relp - Consult the dealer or an experienced radio/TV technician
for help.
FCC ID:
- 1200 FCC ID: X4YXPY12K
- 1230 FCC ID: X4YXPY12K30
17 18
">