Philips Electronics Industries (Taiwan) A3KM131 LCD/ TV Monitor User Manual

Add to My manuals
16 Pages

advertisement

Philips Electronics Industries (Taiwan) A3KM131 LCD/ TV Monitor User Manual | Manualzz

Exhibit

3

Installstion and Operating Instructions

Product Information

Product Features • Technical Specifications • Resolution & Preset Modes •

Philips Pixel Defect Policy • Automatic Power Saving • Physical Specification •

Pin Assignment • Product Views

Product Features

300WN5

z z z z z z z z z z z z

29.5-inch WXGA (1280x768 resolution, 176 degree viewing angle) LCD all-in-one

Monitor TV with excellent display performance

Multiple video input allowing display of PC, TV, HDTV, VCD, DVD, Progressive DVD and Camcorder

Network controllability via RS232 interface for managing the performances, setting, etc.

Digital High Definition Picture (1080i, 720p, 576p, 576i, 480p, 480i)

DCDi

TM

de-interlacinf technology for superior depiction of motion

Picture-in-Picture (PIP) function in PC VGA mode

Light sensor to adjust brightness automatically

Teletext (available only in Asia Pacific and Western Europe)

Digital Nicam/2CS stereo (available only in Asia Pacific and Western Europe)

Component Video Input (YPbPr/YCbCr) for DVD (available in AV and TV models only)

Euroconnector (SCART) (available in Western Europe)

MultiSystem TV tuner-PAL/NTSC (available in TV model only)

RETURN TO TOP OF THE PAGE

Technical Specifications*

LCD PANEL

• Type

• Screen size

• Pixel Pitch

• LCD Panel type

• Effective viewing area

• Display Colors

PC SCANNING

• Vertical refresh rate

• Horizontal frequency

PC VIDEO

• Video dot rate

• Input impedance

TFT LCD

29.5 inch

0.5025 x 0.1675 mm x RGB

1280 x 768 pixels

R.G.B. vertical stripe

Hard coating surface, anti-glare polarizer

(H) 643.2 x (V) 385.92mm

8 bits interface (16.7M colors)

58Hz-60Hz

31kHz-49kHz

< 80 MHz file://W:\DFU\Philips\LCT-TV\300WN5\ENGLISH\300WN5\PRODUCT\PRODUCT.HTM

2004/3/4

Product Information

- Video

- Sync

• Input signal levels

• Sync input signal

75 ohm

2.2K ohm

0.7 Vpp

Separate sync

• Sync polarities

• Input Frequency

• Video interface

Positive and negative

WXGA Hsync 48 kHz, Vsync 60 Hz (N.I.)

SVGA Hsync 38 kHz, Vsync 60 Hz (N.I.)

VGA Hsync 31 kHz, Vsync 60 Hz (N.I.)

D-sub, S-Video, TV-RF, SCART (Europe) or composite and components video (others)

AUDIO

• Input level for

PC/SVHS/SCART

500 mV nominal

• Loudspeaker

5W Stereo Audio (2.5W/channel RMS x2, 200Hz~10kHz, 4 ohm, 10% THD)

OPTICAL CHARACTERISTICS

• Contrast ratio 500:1 (typ.)

• Brightness 500 cd/m

2

(typ.)

• Peak contrast angle

• White Chromaticity

6 o'clock x: 0.283 y: 0.297 (at 9300°K) x: 0.313 y: 0.329 (at 6500°K) x: 0.328 y: 0.344 (at 5700°K)

Upper >88° (typ.)

• Viewing Angle (C/R >5)

• Response time

sRGB

Lower >88° (typ.)

Left >88° (typ.)

Right >88° (typ.)

<=16ms (typ.)

Page 2 of 7 sRGB is a standard for ensuring correct exchange of colors between different devices (e.g. digital cameras, monitors, printers, scanners, etc.)

Using a standard unified color space, sRGB will help represent pictures taken by an sRGB compatible device correctly on your sRGB enabled Philips monitors. In that way, the colors are calibrated and you can rely on the correctness of the colors shown on your screen.

Important with the use of sRGB is that the brightness and contrast of your monitor is fixed to a predefined setting as well as the color gamut. Therefore it is important to select the sRGB setting in the monitor's OSD.

To do so, at PC mode, open the OSD by pressing the MENU button of your monitor. Use the down button to go to COLOR SETTINGS and press MENU again. Then move the down file://W:\DFU\Philips\LCT-TV\300WN5\ENGLISH\300WN5\PRODUCT\PRODUCT.HTM

2004/3/4

Product Information button to go to NORMAL COLOR and press MENU again.

For more information on sRGB, please visit: www.srgb.com

Page 3 of 7

* This data is subject to change without notice.

RETURN TO TOP OF THE PAGE

Resolution & Preset Modes

• Recommended

10 factory preset modes:

Resolution

PC

640*480

800*600

1024*768

1280*768

1280 x 768 at 60Hz

Mode

VGA VESA 60

SVGA VESA 60

XGA VESA 60

GTF 60

H. freq (kHz)

31.469

37.879

48.363

47.700

Video

EDTV

SDTV

EDTV

SDTV

HDTV

HDTV

480P

480i

576P

576i

1080i

720P

31.470

15.734

31.250

15.625

33.750

45.000

V. freq (Hz)

59.940

60.317

60.004

60.000

60.000

59.940

50.000

50.000

60.000

60.000

RETURN TO TOP OF THE PAGE

Automatic Power Saving

If you have VESA DPMS compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the monitor will then 'wake up' automatically. The following table shows the power consumption and signaling of this automatic power saving feature:

Power Management Definition

Power LED

file://W:\DFU\Philips\LCT-TV\300WN5\ENGLISH\300WN5\PRODUCT\PRODUCT.HTM

2004/3/4

Product Information Page 4 of 7

VESA Mode

ON

Video

Active

H-sync

Pulse

V-sync

Pulse

Used

130W (typ.)

color

Blue

OFF Blanked No No < 5W Amber

AC OFF Blanked No No < 2W Off

This monitor is

E

NERGY

S

TAR

®

compliant.

A

s an

E

NERGY

S

TAR

®

P

artner,

PHILIPS

has determined that this product meets the

E

NERGY

S

TAR

® guidelines for energy efficiency.

RETURN TO TOP OF THE PAGE

Physical Specifications

• Dimension (WxHxD) *

• Weight

• Power supply

• Power consumption

• Temperature (operating)

• Relative humidity

• System MTBF

867.7mm x 505mm x 183mm (incl. Pedestal, Speakers)

726.7mm x 469.3mm x 115mm (w/o Pedestal, Speakers)

16.0 kg (incl. Pedestal, Speakers)

14.0 kg (w/o Pedestal, Speakers)

15.0 kg (w/o Pedestal, Speakers; with protective cover)

90 — 264 VAC, 50/60 Hz

PC Mode: 130 W (typ.)

TV Mode: 150 W (typ.)

0° C to 35° C

20% to 80%

50K hrs (excluding CCFL 40Khrs)

* This data is subject to change without notice.

RETURN TO TOP OF THE PAGE

Pin Assignment

1. The digital only connector contains 24 signal contacts organized in three rows of eigh contacts. Signal pin assignments are listed in the following table:

Pin

No.

Signal

Assignment

1 T.M.D.S. Data2-

2 T.M.D.S. Data2+

3

T.M.D.S. Data2/4

Pin

No.

Signal

Assignment

9 T.M.D.S. Data1-

10 T.M.D.S. Data1+

11

T.M.D.S. Data1/3

Pin

No.

Signal

Assignment

17 T.M.D.S. Data0-

18 T.M.D.S. Data0+

19

T.M.D.S. Data0/5 file://W:\DFU\Philips\LCT-TV\300WN5\ENGLISH\300WN5\PRODUCT\PRODUCT.HTM

2004/3/4

Product Information

Shield

4 No connect

5 No connect

6 DDC Clock

7 DDC Data

8 No connect

Shield

12 No connect

13 No connect

14 +5V Power

15 Hot Plug Detect

16 Ground (for +5V)

Shield

20 No connect

21 No connect

22

T.M.D.S. Clock

Shield

23 T.M.D.S. Clock+

24 T.M.D.S. Clock-

Page 5 of 7

2. The 15-pin D-sub connector (male) of the signal cable:

Pin

No.

Assignment

1 Red video input

2 Green video input

3 Blue video input

4 Ground

5 NC

6 Red video ground

7 Green video ground

8 Blue video ground

Pin

No.

9

Assignment

DDC +5V

10 Cable detect

11

Identical output, connected to pin 10

12 Serial data line (SDA)

13 H. Sync / H+V

14 V. Sync

15 Data clock line (SCL)

3. RS232 Connector

D-sub 9-pin male connector for communication with plasma engine or PC.

RS-232 (EIA-232-A) Function Pin No.

file://W:\DFU\Philips\LCT-TV\300WN5\ENGLISH\300WN5\PRODUCT\PRODUCT.HTM

2004/3/4

Product Information

8

6

5

3

2

7

1

4

9

4. SCART Connector

Transmit Data (TD) from DTE to DCE

Receive Data (RD) from DCE to DTE

Request to Send (RTS)

Clear to Send (CTS)

DCE Ready (DSR)

Signal Ground (SG)

Received Line Signal Detector (DCD)

DTE Ready (DTR)

Ring Indicator

Pin No.

Signal

1

2

Audio right channel output (0.5 Vrms, < 1K ohms)

Audio right channel input (0.5 Vrms, > 10K ohms)

3

Audio left channel output (0.5 Vrms, < 1K ohms)

4 Audio ground

5 Blue signal ground

6

Audio left channel input (0.5 Vrms, > 10K ohms)

7 Blue signal I/O (0.7 Vp-p, 75 ohms)

8

Function switching I/O (L: < 2V, H: > 10V,

10K ohms)

9 Green signal ground

10 Intercommunication data line No. 1

11 Green signal I/O (0.7 Vp-p, 75 ohms)

12 Intercommunication data line No. 2

13 Red signal ground

14 Blanking signal ground

15 Red signal I/O (0.7 Vp-p, 75 ohms)

16

Blanking signal I/O (L: < 0.4V, H: >1.0V, 75 ohms)

17 Composite video signal ground

Pin No.

2

1

8

9

10

11

12

13

14

15

16

18

6

4

5

3

7

Page 6 of 7 file://W:\DFU\Philips\LCT-TV\300WN5\ENGLISH\300WN5\PRODUCT\PRODUCT.HTM

2004/3/4

Product Information

18 Blanking signal ground

19

Composite video signal output (1 Vp-p, 75 ohms, sync: negative)

20

Composite video signal input (1 Vp-p, 75 ohms, sync: negative)

21 Plug shield (common ground)

17

20

19

21

RETURN TO TOP OF THE PAGE

Product Views

Follow the links to see various views of the monitor and its components.

Product Description

RETURN TO TOP OF THE PAGE

Page 7 of 7 file://W:\DFU\Philips\LCT-TV\300WN5\ENGLISH\300WN5\PRODUCT\PRODUCT.HTM

2004/3/4

Installing your LCD Monitor/TV Page 1 of 7

Installing your LCD Monitor/TV

Product Description • Connecting to Your PC, TV antenna, DVD/VCR etc.

• Getting Started

Performance

Product Description

Side View (Left)

2

3

1

INPUT

5

Selecting input source

Increase or decrease the channel number or moving up or down to highlight the function in OSD

Increase or decrease the level of audio volume or moving left or right of to highlight the sub-menu in the selected function of OSD

Open the OSD or confirm the selected function 4

MENU

DC power switch On/Off

RETURN TO TOP OF THE PAGE

Rear View

TV version

file://W:\DFU\Philips\LCT-TV\300WN5\ENGLISH\300WN5\INSTALL\INSTALL.HTM

2004/3/4

Installing your LCD Monitor/TV Page 2 of 7

1 AC IN

2 AC Power

3 D-Sub

4 PC - Audio

5 DVI-D

6 RS232

AC power in

AC power switch

PC analog D-Sub input

PC Stereo input

PC

RS232 network connection

7

External/

EURO-AV

SCART connection (for Europe only)

8 Composite Video Output Composite video CVBS ouput

9 Audio (L) Output Audio (L) output

Audio (R) Output

10 Audio (L) Output

Audio (R) Output

11 Line out

Audio (R) output

Audio (L) output for the detachable speaker (L)

Audio (R) output for the detachable speaker (R)

Audio output for external speakers

RETURN TO TOP OF THE PAGE

Audio/Video version

file://W:\DFU\Philips\LCT-TV\300WN5\ENGLISH\300WN5\INSTALL\INSTALL.HTM

2004/3/4

Installing your LCD Monitor/TV Page 3 of 7

Monitor version

1 AC IN

2 AC Power

3 D-Sub

4 PC - Audio

5 DVI-D

6 RS232

7

External/

EURO-AV

8 Audio (L) Output

Audio (R) Output

9 Line out

AC power in

AC power switch

PC analog D-Sub input

PC Stereo input

PC

RS232 network connection

SCART connection (for Europe only)

Audio (L) output for the detachable speaker (L)

Audio (R) output for the detachable speaker (R)

Audio output for external speakers

RETURN TO TOP OF THE PAGE file://W:\DFU\Philips\LCT-TV\300WN5\ENGLISH\300WN5\INSTALL\INSTALL.HTM

2004/3/4

Installing your LCD Monitor/TV Page 4 of 7

Side View (Right)

TV version

1 AC IN

2 AC Power

3 D-Sub

4 PC - Audio

5 DVI-D

6 RS232

7 Audio (L) Output

Audio (R) Output

8 Line out

AC power in

AC power switch

PC analog D-Sub input

PC Stereo input

PC

RS232 network connection

Audio (L) output for the detachable speaker (L)

Audio (R) output for the detachable speaker (R)

Audio output for external speakers

RETURN TO TOP OF THE PAGE file://W:\DFU\Philips\LCT-TV\300WN5\ENGLISH\300WN5\INSTALL\INSTALL.HTM

2004/3/4

Installing your LCD Monitor/TV Page 5 of 7

1 Audio (L)

2 Audio (R)

3 Component Video

4 Composite Video

5 Audio (L)

6 Audio (R)

7 S-Video

8 RF 75

Audio (L) for component video

Audio (R) for component video

Component video Y/Pb/Pr input

Composite video CVBS input

Audio (L) for CVBS and S-Video

Audio (R) for CVBS and S-Video

S-Video input

TV Antenna or CATV cable in

RETURN TO TOP OF THE PAGE

Audio/Video version

file://W:\DFU\Philips\LCT-TV\300WN5\ENGLISH\300WN5\INSTALL\INSTALL.HTM

2004/3/4

Installing your LCD Monitor/TV Page 6 of 7

1 Audio (L)

2 Audio (R)

3 Component Video

4 Composite Video

5 Audio (L)

6 Audio (R)

7 S-Video

Audio (L) for component video

Audio (R) for component video

Component video Y/Pb/Pr input

Composite video CVBS input

Audio (L) for CVBS and S-Video

Audio (R) for CVBS and S-Video

S-Video input

RETURN TO TOP OF THE PAGE

Optimising Performance

z For best performance, ensure that your display settings are set at 1280x768, 60Hz.

Note: You can check the current display settings by pressing the 'MENU' button once. z You can also install the Flat Panel Adjust (FP Adjust) program, a program for getting the best performan monitor. This is included on this CD. Step-by-step instructions are provided to guide you through the ins

Click on the link to find out more about this program.

More about FP_setup04.exe

file://W:\DFU\Philips\LCT-TV\300WN5\ENGLISH\300WN5\INSTALL\INSTALL.HTM

2004/3/4

Installing your LCD Monitor/TV

RETURN TO TOP OF THE PAGE

Page 7 of 7 file://W:\DFU\Philips\LCT-TV\300WN5\ENGLISH\300WN5\INSTALL\INSTALL.HTM

2004/3/4

Regulatory Information Page 1 of 2

Federal Communications Commission (FCC) Notice (U.S. Only)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: z z z z

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer device.

To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture.

THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN

INTERFERENCE-CAUSING EQUIPMENT REGULATIONS.

RETURN TO TOP OF THE PAGE

Commission Federale de la Communication (FCC Declaration)

Cet équipement a été testé et déclaré conforme auxlimites des appareils numériques de class B,aux termes de l'article 15 Des règles de la FCC. Ces limites sont conçues de façon à fourir une protection raisonnable contre les interférences nuisibles dans le cadre d'une installation résidentielle. CET appareil produit, utilise et peut émettre des hyperfréquences qui, si l'appareil n'est pas installé et utilisé selon les consignes données, peuvent causer des interférences nuisibles aux communications radio. Cependant, rien ne peut garantir l'absence d'interférences dans le cadre d'une installation particulière. Si cet appareil est la cause d'interférences nuisibles pour la réception des signaux de radio ou de télévision, ce qui peut être décelé en fermant l'équipement, puis en le remettant en fonction, l'utilisateur pourrait essayer de corriger la situation en prenant les mesures suivantes: z z

Réorienter ou déplacer l'antenne de réception.

Augmenter la distance entre l'équipement et le récepteur. file://W:\DFU\Philips\LCT-TV\300WN5\ENGLISH\300WN5\SAFETY\REGS\REGULAT.H...

2004/3/4

Regulatory Information z z

Brancher l'équipement sur un autre circuit que celui utilisé par le récepteur.

Demander l'aide du marchand ou d'un technicien chevronné en radio/télévision.

Toutes modifications n'ayant pas reçu l'approbation des services compétents en matière de conformité est susceptible d'interdire à l'utilisateur l'usage du présent

équipement.

N'utiliser que des câbles RF armés pour les connections avec des ordinateurs ou périphériques.

CET APPAREIL NUMERIQUE DE LA CLASSE B RESPECTE TOUTES LES EXIGENCES DU

REGLEMENT SUR LE MATERIEL BROUILLEUR DU CANADA.

RETURN TO TOP OF THE PAGE

Page 2 of 2 file://W:\DFU\Philips\LCT-TV\300WN5\ENGLISH\300WN5\SAFETY\REGS\REGULAT.H...

2004/3/4

advertisement

Key Features

  • 29.5-inch WXGA (1280x768 resolution, 176 degree viewing angle) LCD all-in-one Monitor TV with excellent display performance
  • Multiple video input allowing display of PC, TV, HDTV, VCD, DVD, Progressive DVD and Camcorder
  • Network controllability via RS232 interface for managing the performances, setting, etc.
  • Digital High Definition Picture (1080i, 720p, 576p, 576i, 480p, 480i)
  • DCDiTM de-interlacinf technology for superior depiction of motion
  • Picture-in-Picture (PIP) function in PC VGA mode
  • Light sensor to adjust brightness automatically
  • Teletext (available only in Asia Pacific and Western Europe)
  • Digital Nicam/2CS stereo (available only in Asia Pacific and Western Europe)
  • Component Video Input (YPbPr/YCbCr) for DVD (available in AV and TV models only)

Related manuals

Frequently Answers and Questions

Is this product compatible with various devices like PC, TV, DVD, etc?
Yes, it supports multiple video inputs allowing display of PC, TV, HDTV, VCD, DVD, Progressive DVD and Camcorder.
Can this device adjust brightness automatically?
Yes, it has a light sensor to adjust brightness automatically.
What kind of stereo does this product support?
It supports Digital Nicam/2CS stereo (available only in Asia Pacific and Western Europe).

advertisement