Sennheiser DW Pro1/Pro2 wireless headset system Instruction manual
إعلان
إعلان
DW Pro1/Pro2
Instruction manual
Comfort calls
Contents
Contents
Important safety information ................................................................................... 2
The DW Pro1/Pro2 wireless headset system ...................................................... 4
Delivery includes ............................................................................................................. 5
Product overview ............................................................................................................ 6
Base station ................................................................................................................. 6
Pro1/Pro2 headset ................................................................................................... 7
Overview of the buttons .............................................................................................. 8
Overview of the LEDs ..................................................................................................... 9
Putting the headset system into operation ..................................................... 10
Putting the base station into operation ....................................................... 10
Putting the headset into operation ................................................................ 16
Testing the headset system in Phone mode and adjusting it .............. 17
Testing the headset system in PC mode and adjusting it ...................... 19
Adjusting advanced settings ............................................................................. 20
Using the headset system ........................................................................................ 22
Charging the headset rechargeable battery ............................................... 22
Switching the headset on/off ........................................................................... 23
Establishing a wireless link between headset and base station ......... 23
Putting the headset on and adjusting it ....................................................... 24
Calling via the fixed line phone using the headset ................................... 25
Calling via the PC using the headset ............................................................... 26
Switching between Phone and PC mode ....................................................... 28
Holding a conference call .................................................................................... 28
Adjusting the volume ........................................................................................... 29
Muting the headset’s microphone .................................................................. 30
Using the advanced functions .......................................................................... 30
If you leave the DECT range ............................................................................... 31
Cleaning and maintaining the headset system .............................................. 32
Replacing the ear pad(s) ..................................................................................... 32
Replacing the headset’s rechargeable battery ........................................... 33
If a problem occurs ..................................................................................................... 35
Accessories and spare parts .................................................................................... 36
Specifications ................................................................................................................. 37
Manufacturer Declarations ...................................................................................... 39
Index .................................................................................................................................. 41
1
2
Important safety information
Important safety information
• Please read this instruction manual carefully and completely before using the product.
• Make the instruction manual easily accessible to all users at all times.
Always include the instruction manual when passing the product on to third parties.
• Do not use the product in situations which require special attention
(e.g. when performing skilled jobs).
• Always keep the product dry and do not expose it to extreme temperatures (normal operating temperatures: +5°C/+41°F to +45°C/+113°F).
• Use the product with care and store it in a clean, dust-free environment.
• Switch off the headset after use to conserve battery power.
• Only use the DW series
* base station for charging DW series headsets fitted with the DW series rechargeable battery. Never try to charge other rechargeable batteries or non-rechargeable batteries in the
DW series base station.
• Do not short-circuit the contacts of the product. Make sure that no metal objects (e.g. paper clips, hair pins, earrings) come into contact with the interfaces and contacts.
• Sennheiser Communications is not liable for damages resulting from the loss of connection due to a run flat battery, an old battery or exceeding the DECT transmission range.
• This equipment generates, uses and can radiate radio frequency energy and, if not used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
• The DW series headsets contain magnets that generate a magnetic field which could cause interference with cardiac pacemakers and implanted defibrillators. Keep the DW series headsets at least 1.2”
(3 cm) from cardiac pacemakers or implanted defibrillators!
• Protect your hearing from high volume levels.
• Only use the power supply units supplied by Sennheiser Communications.
• To reduce the risk of fire or electric shock, do not use the product near water and do not expose it to rain or moisture.
• Unplug the power supply unit from the wall socket
– to completely disconnect the product from the mains power supply
– during lightning storms or
– when unused for long periods of time.
• Only operate the power supply unit from the type of power source specified in the chapter “Specifications” (see page 37).
• Ensure that the power supply unit is
– in a safe operating condition and easily accessible,
– properly plugged into the wall socket,
– only operated within the permissible temperature range,
* The DW series comprises the following products: DW Office, DW Office USB, DW Pro1/
Pro2, DW Pro1/Pro2 USB. The DW 800 is not part of the DW series.
Important safety information
– not covered or exposed to direct sunlight for longer periods of time in order to prevent heat accumulation (see “Specifications” on page 37).
• Do not operate the product near any heat sources.
• Only use attachments/accessories specified by Sennheiser Communications (see “Accessories” on page 36).
• Keep plastic wrap and plastic bags of the packaging out of reach of children – danger of suffocation!
Intended use
Intended use of the product includes
• having read this instruction manual, especially the chapter “Important safety information” on page 2,
• using the product within the operating conditions and limitations described in this instruction manual.
“Improper use” means using the product other than as described in this instruction manual, or under operating conditions which differ from those described herein.
Safety instructions for the Lithium-Polymer rechargeable batteries
If abused or misused, rechargeable batteries may leak. In extreme cases, rechargeable batteries may even present
• a heat hazard,
• a fire hazard,
• an explosion hazard,
• a smoke or gas hazard.
Please understand that Sennheiser Communications does not accept liability for damage arising from abuse or misuse.
Keep away from children.
Do not short-circuit.
Do not expose to moisture.
Do not heat above +45°C/
+113 °F, e.g. do not expose to sunlight or throw into a fire.
Do not mutilate or dismantle.
Only charge rechargeable batteries at ambient temperatures between +5°C/+41°F to
+45°C/+113 °F.
When not using rechargeable batteries for extended periods of time, charge them regularly
(every six months for about one hour).
Do not charge the rechargeable battery if the device is obviously defective.
Only charge rechargeable batteries with an appropriate
Sennheiser Communications charger.
Store in a cool and dry place at room temperature (approx.
20°C/68°F).
Return defective devices or devices with defective rechargeable batteries to your specialist dealer.
3
4
The DW Pro1/Pro2 wireless headset system
The DW Pro1/Pro2 wireless headset system
The Sennheiser Communications DW Pro1/Pro2 is a wireless DECT headset system which is intended for professional call center and office use.
• Can be used with a fixed line phone or PC (VoIP)
• Quick link establishment between headset and base station
• Excellent sound quality in narrowband and wideband mode ensures optimum speech intelligibility
• Range of up to 180 m in free line of sight and up to 55 m indoors
• Two headset variants with padded headband and supra-aural ear cup(s):
– variant Pro1 covers one ear (monaural)
– variant Pro2 covers both ears (binaural) and offers best passive attenuation of ambient noise
• Flexible microphone boom for individual wearing comfort – allows wearing of the microphone on either the left or right-hand side
• Ultra Noise cancelling microphone for optimum speech intelligibility without annoying background noise
• Permits conference calls with up to 4 headsets
• Quick and easy pairing of a new headset
• Long battery operating time:
– up to 12 hours of talk time in narrowband mode
– up to 8 hours of talk time in wideband mode
– up to 4 days of standby time
• Quick and convenient charging of the headset (1 hour)
• HeadSetup software for convenient call control and headset management via a PC
• Headset can be integrated into existing DECT GAP systems
DECT
The Sennheiser Communications DW wireless headset system uses DECT radio technology. Due to a dynamic adjustment of the transmission power, the DECT technology offers an increased transmission range, minimized radiation exposure and has a good energy efficiency. Encrypted radio transmission provides maximum security for wireless communication.
Delivery includes
Delivery includes
1 base station
1 headset with built-in rechargeable battery:
– Pro1 variant: covers one ear (monaural)
– Pro2 variant: covers both ears (binaural)
1 power supply unit
1 telephone cable
1 USB cable
1 safety guide (booklet with important safety information)
1 quick guide
1 CD ROM (including, among other things, the HeadSetup software and a detailed instruction manual as PDF)
5
Product overview
Product overview
Base station
6
PC button with LED
Charging contacts
PHONE button with LED
LINK LED
CHARGE STATUS LED
ABC switch
Microphone volume control
Phone socket
Handset socket
ACC socket
DIP switch row 1 to 6
DC IN socket
PC socket (USB)
Cover with overview of DIP switch assignment
Power supply unit
DC IN connector
Telephone cable
USB cable
Pro1/Pro2 headset
7
Pro1
A
Microphone
Windshield
Name plate
HEADSET LED
LINK button
AUDIO button
9
A
7
8
Pro2
9
1
A
8
3
2
4
5
6
0
Headband
Battery compartment cover
Ear pad
Charging contacts
1
2
Product overview
7
8
Overview of the buttons
�
5
6
Overview of the buttons
Base station
�
Action
Press the
PHONE button
Button
Press the
PC button �
Functions
Selects the Phone mode
Establishes/disconnects the link between headset and base station
Page
25
23
Accepts/ends a call (with electronic call control/ handset lifter)
Selects the PC mode
Establishes/disconnects the wireless link between headset and base station
Accepts/ends a call
(depending on the softphone used)
25
26
23
26
Headset
Action
Press the
LINK button �
Press and hold the
LINK button � for
5 seconds
Button
5 s
Functions
Establishes/disconnects the link between headset and base station
Page
23
Accepts/ends a call (with electronic call control/ handset lifter or depending on the softphone used)
Switches the headset on/off
25/
26
23
Push the
AUDIO button � forwards/backwards
Press the
AUDIO button �
Press and hold the
LINK button � and the AUDIO button � for 5 seconds
5 s
5 s
Increases/reduces the ring tone volume, the volume of the acoustic signals or the audio volume by 1 step
Mutes the microphone/ unmutes the microphone
29
30
Setting mode
GAP pairing mode
Swaps the assignment of the AUDIO button �
31
16
4
Overview of the LEDs
Overview of the LEDs
Base station
LED of the PC button lights up flashes
LED of the PHONE button lights up flashes
LINK LED lights up blue lights up red flashes red is off
Meaning
PC mode
Incoming PC call
Meaning
Phone mode
Incoming telephone call
Meaning
Active link to the headset
No link to the headset
Headset is muted
Standby mode
Base station is switched off (not powered)
CHARGE STATUS LED
LED segment* Battery charge
1
2
3
4
0-25%
25-50%
50-75%
75-100%
Required charging time approx. 10 min approx. 10 min approx. 20 min total: approx.
60 min approx. 20 min
* during charging, each segment gets brighter in 5 steps
When the LED segment 1 flashes in rapid succession, the battery is almost flat. You have to recharge the battery within the next few minutes (see page 22).
Headset
LED HEADSET lights up blue flashes blue slowly flashes red if off flashes blue/red
Meaning
Charging mode
Active link to base station
Rechargeable battery is almost flat
Standby mode
Headset is switched off
Setting mode/GAP pairing mode
Pairing of an additional headset to the base station
9
Putting the headset system into operation
Putting the headset system into operation
Putting the base station into operation
You can use the headset system with your fixed line phone ( Phone mode) and/or your PC ( PC mode). The base station controls the wireless communication between the products.
Removing/attaching the cover
To remove the cover:
Remove the cover by inserting a finger into the recess as shown.
To attach the cover and to secure the connected cables:
Replace the cover to the rear of the base station (see diagram).
Tilt the cover upwards until it locks into place.
10
Putting the headset system into operation
Connecting the base station to the mains power supply
The base station is ready for operation as soon as it is connected to the mains power supply.
Connect the DC IN connector of the power supply unit to the DC IN socket .
Plug the power supply unit into a wall socket.
The LINK LED lights up red. The LED of the last used mode button
(PHONE or PC ) lights up white.
When using the headset system only in PC mode, the power from the PC via the USB cable is sufficient to power the base station. For charging the rechargeable battery within the specified charging times (see page 22) and for use in Phone mode, the power supply unit is required.
Connecting the base station to a fixed line phone
If your telephone features a headset socket for connecting the electronic call control, please use this socket.
To connect the base station to a fixed line phone, choose one of the follow options:
Possibility Connection
A to a fixed line phone without headset socket
B to a fixed line phone with headset socket
C of an optional mechanical handset lifter
(with connection possibilities A and B only)
D to an optional electronic hook switch control (EHS)
Choose your connection possibility and proceed as described under A ,
B , C or D on the following pages.
For additional information on the individual settings for the headset system via the DIP switch row , refer to page 20.
11
Putting the headset system into operation
A Connection to a fixed line phone without headset socket
Disconnect the handset cable from the telephone.
Connect the handset cable to the Handset socket .
Use the telephone cable to connect the Phone socket to the handset socket on the telephone.
Set the DIP switch # 1 and # 2 to the upper position.
B Connection to a fixed line phone with headset socket
Use the telephone cable to connect the Phone socket to the headset socket on the telephone.
Set the DIP switch # 1 and # 2 to the upper position.
12
Putting the headset system into operation
C Connection of an optional mechanical handset lifter
(with connection possibilities A and B only)
You can also connect the HSL 10 mechanical handset lifter from Sennheiser
Communications (see “Accessories and spare parts” on page 36):
Connect the base station to the fixed line phone as described under A or B .
Connect the handset lifter to the ACC socket on the base station.
Connect the handset lifter to the fixed line phone as described in the instruction manual of the handset lifter.
D Connection to an optional electronic hook switch control (EHS)
If your telephone has a built-in electronic hook switch, supporting either the DHSG or the MSH standard, you require the corresponding connection cables. Other hook switch standards require suitable adapter cables which convert the control signals to the DHSG standard (see “Accessories and spare parts” on page 36).
DHSG standard
DHSG cable e.g. Siemens, Aastra, Agfeo, etc.
Other standards
DW Pro1/Pro2 DHSG setting
Adapter cable e.g. Cisco, Avaya, Polycom DW Pro1/Pro2 DHSG setting
If your telephone has a built-in electronic hook switch supporting the DHSG or the any other hook switch standard (except for the MSH standard):
Set the DIP switch # 1 to the lower position.
Set the DIP switch # 2 to the upper position.
13
Putting the headset system into operation
MSH standard
MSH cable e.g. Alcatel DW Pro1/Pro2 MSH setting
If your telephone has a built-in electronic hook switch supporting the MSH standard:
Set the DIP switch # 1 to the upper position.
Set the DIP switch # 2 to the lower position.
The necessary connection and adapter cables are available from your
Sennheiser partner. For additional information, please visit our website at www.senncom.com/headsetselector.
Setting up the base station
Place the base station at a minimum distance of 15 to 20 cm from the fixed line phone.
Connecting the base station to a PC
You can connect the headset system to a PC in order to use it for Internet telephone (VoIP) with softphones or multimedia applications.
Use the USB cable to connect the PC socket to a USB socket of your PC.
The operating system detects the USB audio device “Sennheiser DECT” and installs the necessary drivers.
14
Putting the headset system into operation
Installing the HeadSetup software
The HeadSetup software enables the headset system to communicate with a wide variety of softphones and allows you to use the call control functions. Even without the HeadSetup software, the headset system can still be used as an audio input and output device.
Updates and additional information on the HeadSetup software can be found on our website at www.senncom.com/headsetup or via the update function of the software.
Specifications (version 2.2)
File size
Supports the call control functions of the following softphones approx. 20 MB
Supported operating systems Microsoft Windows 2000
Microsoft Windows XP
Microsoft Windows Vista
Microsoft Windows 7
AOL Instant Messenger
Avaya IP Softphone 4.0x - 5.0x - 6.0x
Avaya One-X Communicator
Cisco IP Communicator Version 2.0 - 2.1
IBM Lotus Sametime Connect
Skype
To install the HeadSetup software:
Run the “HeadSetup USB version X.X.exe” file in the “HeadSetup” folder on the enclosed CD ROM.
Follow the instructions of the install program.
Additional Information and application hints can be found in the Help section of the software:
Click the “Help ...” button.
15
Putting the headset system into operation
50%
100%
20 min
1 h
Putting the headset into operation
The microphone boom of the Pro1/Pro2 headset can be swiveled, allowing the microphone to be worn on the left or right-hand side (see page 24).
Before using the headset for the first time, charge the rechargeable battery for at least 20 minutes (see page 22).
Labeling the headset
The name plate allows you to label the headset.
Change the lettering of the name plate as shown.
The “Nameplate-template.pdf” PDF file included on the CD ROM allows you to create and print individual name plates.
3
3
Swapping the assignment of the AUDIO button
The assignment of the AUDIO button can be swapped depending on whether you wear the headset on the right or left ear. By default, the headset is configured for wearing on the right ear. Pushing the AUDIO button backwards increases the volume, pushing it forwards reduces the volume (see page 29).
To swap the assignment of the AUDIO button :
Simultaneously press and hold the headset’s LINK button and
AUDIO button for 5 seconds.
The HEADSET LED flashes blue/red.
16
4
Putting the headset system into operation
Push the AUDIO button in the direction in which you want to increase the volume until the HEADSET LED goes off.
The headset switches to standby mode.
5 s
Right
5
6
Left
Testing the headset system in Phone mode and adjusting it
Testing the telephone connection
When PC mode is selected (the LED of the PC button lights up white):
Press the PHONE button on the base station.
The base station is set to Phone mode and the LED of the PHONE button lights up white.
Press either the LINK button on the headset or the PHONE button
on the base station.
A wireless link is established between the headset and the base station, the LINK LED lights up blue and the HEADSET LED flashes blue.
4
5
Lift the handset (If a handset lifter is connected, it automatically lifts the handset).
The system is correctly connected if you can hear a clear dial tone and if the other party can hear you at a comfortable level.
If the audio signal/dial tone is disturbed, adjust the audio signal (see page 18). If the other party cannot hear you well, adjust the microphone sensitivity (see page 18).
17
Putting the headset system into operation
Adjusting the audio signal/dial tone
Set the ABC switch to A (default setting), B or C so that you can hear a clear dial tone in the headset.
Adjusting the microphone sensitivity
By default, the microphone volume control is set to between position 4 and position 5 . This setting is suitable for most telephones and your voice gets reproduced at a good volume. To change the volume, adjust the microphone volume control accordingly.
The microphone volume control only adjusts the microphone sensitivity in Phone mode.
Make a call to someone who will help you find the correct sensitivity setting for your microphone (see page 25).
Turn the microphone volume control so that the other party can hear at a comfortable level.
18
Putting the headset system into operation
Testing the headset system in
PC
mode and adjusting it
Testing the PC connection
When Phone mode is selected (the LED of the PHONE button lights up white):
Press the PC button on the base station.
The base station is set to PC mode and the LED of the PC button lights up white.
Press either the LINK button on the headset or the PC button on the base station.
A wireless link is established between the headset and the base station, the LINK LED lights up blue and the HEADSET LED flashes blue.
4
5
Use your softphone to make a call to someone who will help you adjust the correct microphone sensitivity for PC mode (see below).
The system is correctly connected if the other party can hear you at a comfortable level.
Adjusting the microphone sensitivity
Depending on the operating system used, adjust the microphone sensitivity so that the other party can hear you at a comfortable level (see the instruction manual of your operating system).
Some softphones provide automatic adjustment of the microphone sensitivity. If possible, activate this function in order to be able to use the headset microphone to the full.
19
Putting the headset system into operation
Adjusting advanced settings
The DIP switch row allows you to adjust the headset system to your individual needs. By default, all DIP switches are set to the upper position.
To change the settings of the DIP switch row :
If necessary, disconnect an existing wireless link between base station and headset (see page 23).
Use a pointed object (e.g. a pen) to set the DIP switches to the desired position.
Configuring the handset lifter/hook switch – DIP switch 1 and 2
Switch position Function
Manual operation
Lifts/hangs up the handset manually or using the handset lifter.
Electronic hook switch (DHSG standard)
Call control via the DW Pro1/Pro2 headset system.
Electronic hook switch (MSH standard)
Call control via the DW Pro1/Pro2 headset system.
Manual operation
Lifts/hangs up the handset manually or using the handset lifter.
Adjusting the radio range – DIP switch 3
If many DECT systems are operated in a confined space, interference can occur. In this case, you should change the radio range.
Switch position Function
Standard radio range
Reduced radio range
Use this setting in order to avoid interference with other
DECT systems.
Range of approx. 10 m indoors
20
Putting the headset system into operation
Automatically establishing the wireless link between headset and base station (Auto Link) – DIP switch 4
Switch position Function
Switched off
You have to manually establish the wireless link
(see page 23).
Switched on
When taking the headset out of the base station, a wireless link is automatically established between headset and base station (Auto Link).
Switching between wideband and narrowband mode – DIP switch 5
Switch position Function
Wideband mode
Automatic frequency adjustment of wideband and narrowband calls in PC and Phone mode.
Battery life: 8 hours
Narrowband mode
Narrowband audio transmission in PC and Phone mode.
Battery life: 12 hours
Limiting the volume – DIP switch 6
Switch position Function
Standard limitation
Limited volume (country specific)
• AUS version: in compliance with Directive AS/ACIF S004:2008
• EU and US version: in compliance with Directive 2003/10/EC
21
Using the headset system
Using the headset system
Charging the headset rechargeable battery
If you charge the rechargeable battery for the first time, allow charging for at least 20 minutes without interruption. A complete charging process takes about 60 minutes. You can interrupt charging at any time without damaging the rechargeable battery.
Operating time with a fully charged rechargeable battery:
Talk time/standby time
12 hours
8 hours
4 days
Mode narrowband mode (see page 21) wideband mode (see page 21) standby mode
To charge the rechargeable battery of the Pro1/Pro2 headset:
Place the headset into the magnetic holder of the base station.
The HEADSET LED lights up blue and the CHARGE STATUS LED indicates the battery charge:
3
4
LED segment* Battery charge
1 0-25%
2 25-50%
50-75%
75-100%
Required charging time approx. 10 min approx. 10 min approx. 20 min total: approx.
60 min approx. 20 min
* during charging, each segment gets brighter in 5 steps
After completion of the charging process, the HEADSET LED goes off.
4
Pro1 Pro2
To stop the charging process:
Take the headset out of the base station.
The CHARGE STATUS LED indicates the remaining battery charge of the headset.
22
5
Using the headset system
When the battery is about to run flat ...
... only the LED segment 1 lights up weakly or flashes (see page 9).
... the HEADSET LED � flashes red.
... you hear a low battery warning (three beeps)in the headset.
... you have several minutes of battery reserve.
When the battery is flat, the headset switches off.
If the headset is outside the range of the base station, it will switch off after 30 minutes in order to conserve battery power.
4
Switching the headset on/off
If you place the headset into the base station, the headset automatically switches to standby mode. In standby mode, the power consumption is very low and the radiated power is reduced to a minimum. The HEADSET LED � lights up blue during charging.
Switching the headset on
Press and hold the LINK button � for 5 seconds.
The HEADSET LED � flashes blue 3 times and the wireless link to the base station is established (where required). An ascending confirmation beep is heard in the headset.
4
Switching the headset off
Press and hold the LINK button � for 5 seconds.
The HEADSET LED � flashes red 3 times.
Establishing a wireless link between headset and base station
To establish a wireless link between headset and base station:
Press the LINK button � on the headset.
The link is established. The LINK LED � lights up blue and the
HEADSET LED � flashes blue.
To disconnect a wireless link between headset and base station:
Press the LINK button � on the headset.
The link is disconnected. The LINK LED � and the HEADSET LED � go off.
5
23
Using the headset system
Left Right
You can also establish or disconnect the wireless link by pressing the PC button or the PHONE button on the base station
(depending on the selected mode ( PC or Phone ), see page 28).
If your telephone has a built-in electronic hook switch supporting the MSH standard (see page 13), you can only disconnect the wireless link between headset and base station by placing the headset into the base station. The control signals (“accept a call”, “end a call”) of the headset are still transmitted to the electronic hook switch without any restrictions.
Putting the headset on and adjusting it
Rotate the microphone boom as shown.
Carefully bend the flexible microphone boom so that the microphone points towards your mouth.
Maintain a distance of about 0.8-1.2“ (2-3 cm) between the microphone and the corner of the mouth.
If you are using the Pro1 headset:
Put on the headset so that the ear pad rests comfortably on your left or right ear and that the headband runs over the top of your head.
If you are using the Pro2 headset:
Put on the headset so that the ear pads rest comfortably on your ears.
7
Pro1
9
Pro2
9
1
2-3 cm
24
Using the headset system
Calling via the fixed line phone using the headset
Accepting an incoming call
You hear the ring tone of the fixed line phone:
Put on the headset and establish a wireless link between headset and base station (see page 23).
If you are using a handset lifter/electronic hook switch, the call is automatically accepted.
If you receive a call and a handset lifter/electronic hook switch with ring tone detection is used, you hear a ring tone in the headset and the LED of the PHONE button flashes white.
If you are not using a handset lifter/electronic hook switch:
Accept the call by lifting the handset or by pressing the “accept call” button on your fixed line phone.
Making a call
If you are using a handset lifter/electronic hook switch:
Dial the desired number.
Put on the headset and establish a wireless link between headset and base station (see page 23).
The phone connection is established automatically.
If you are not using a handset lifter/electronic hook switch:
Put the headset on and establish a wireless link between headset and base station (see page 23).
Lift the handset and dial the desired number.
The phone connection is established.
25
Using the headset system
Ending a call
Disconnect the wireless link between headset and base station (see page 23).
If you are using handset lifter/electronic hook switch, the call is automatically ended.
If you are not using a handset lifter/electronic hook switch:
Hang up the handset or press the “end call” button on your fixed line phone.
Transferring a call from the headset to the fixed line phone and vice versa
This function is only available if you are not using a handset lifter/electronic hook switch or if your telephone supports this function.
If a wireless link is established (see page 23):
Speak into the headset.
If no wireless link is established (see page 23):
Speak into the handset.
Calling via the PC using the headset
Accepting an incoming PC call
If you receive a call on your softphone:
Establish a wireless link between headset and base station (see page 23).
If the call control function of your softphone is supported, the call is automatically accepted (see page 15).
If your softphone does not support call control:
Accept the call using your softphone.
If you receive a call and the call control function of your softphone is supported by the HeadSetup software (see page 15), you hear a ring tone in the headset and the LED of the PC button flashes white.
26
Using the headset system
Making a PC call
Establish a wireless link between headset and base station (see page 23).
Make the call using your softphone.
Ending a PC call
Disconnect the wireless link between headset and base station (see page 23).
If the call control function of your softphone is supported, the call is automatically ended (see page 15).
If your softphone does not support call control:
End the call using your softphone.
Reproducing PC audio via the headset
The HeadSetup software allows you to listen to all PC audio via the headset.
To activate/deactivate the reproduction of PC audio via the headset:
In the HeadSetup software, activate/deactivate the “Always Audio” function by clicking the corresponding button.
All PC audio is permanently reproduced via the headset. The wireless link between headset and base station remains permanently established.
If the “Always Audio” function is deactivated, the icon on the button is crossed out in red.
27
Using the headset system
If the “Always Audio” function is activated, you can still accept calls via the Phone mode. After ending the call, the base station automatically switches back to PC mode and all PC audio is reproduced via the headset.
Switching between Phone and PC mode
You can switch between Phone and PC mode and accept calls of the other mode.
Press the PC button or the PHONE button on the base station to select the desired mode.
The LED of the PC button or the LED of the PHONE button lights up white, indicating the selected mode.
GUEST
MASTER
Holding a conference call
The headset system allows you to hold a conference call with up to 4 headsets. The master headset is used to control the conference call and up to
3 additional guest headsets can participate in the conference call.
28
5
4
Using the headset system
To start the conference call using the master headset:
Establish a wireless link between headset and base station (the LINK
LED flashes blue).
To add a guest headset to the conference call:
Place the guest headset to be added to the conference call into the base station of the master headset.
The HEADSET LED flashes blue/red and the headset pairs to the base station. If pairing was successful, the HEADSET LED lights up blue.
Take the guest headset out of the base station.
You hear a beep in the master headset.
Press the LINK button on the master headset within 15 seconds.
The guest headset is enabled for the conference call.
If necessary, repeat this procedure for the two other guest headsets.
Call the other party.
To exit the conference call with a guest headset:
Press the LINK button on the guest headset.
To end the conference call:
Use the master headset to end the conference call.
The wireless links to all other headsets participating in the conference call are disconnected.
You can only end the conference call using the master headset.
Other functions such as volume adjustment and muting the headset’s microphone can still be performed on each headset.
Adjusting the volume
WARNING Hearing damage due to high volumes!
Listening at high volume levels for long periods can lead to permanent hearing defects.
Set the volume to a medium level.
Do not continuously expose yourself to high volumes.
In order to be able to adjust the volume of the ring tone and the acoustic signals, the headset has to be in standby mode. In order to be able to adjust the audio volume, a wireless link has to be established between headset and base station (see page 23).
In PC mode, you can adjust the volume using the AUDIO button or by using the volume control of your operating system (see the instruction manual of your operating system).
29
Using the headset system
The volumes can be adjusted in several steps. When the minimum or maximum volume is reached, you hear a double beep in the headset.
To increase or reduce the volume step-by-step, push the AUDIO button backwards or forwards.
The assignment of the AUDIO button can be swapped depending on whether you wear the headset on the right or left ear (see
“Swapping the assignment of the AUDIO button ” on page 16).
6
Vol +
Vol –
MUTE Mic 6
Muting the headset’s microphone
To mute the headset’s microphone during a call (the LINK LED on the base station lights up blue):
Press the AUDIO button .
The microphone is muted. While the microphone is muted, you hear a beep in the headset every 5 seconds and the LINK LED on the base station flashes red.
To unmute the headset’s microphone:
Press the AUDIO button again.
You hear a low confirmation beep in the headset. or
Disconnect the wireless link between headset and base station (see page 23).
In both cases, the muting is canceled and the LINK LED lights up blue again or goes off.
Using the advanced functions
Pairing additional headsets for shared use
You can use one DW series base station with different DW series * headsets. This can be advantageous if you share a telephone workplace. The last headset paired to the base station can be used without more ado.
If no wireless link is established between headset and base station:
Place the additional headset into the magnetic holder of the base station.
During pairing of the headset to the base station, the HEADSET LED flashes blue/red. If pairing was successful, the HEADSET LED lights up blue. You can now use the newly paired headset.
* The DW series comprises the following products: DW Office, DW Office USB, DW Pro1/
Pro2, DW Pro1/Pro2 USB. The DW 800 is not part of the DW series.
30
Using the headset system
Pairing the headset to third party DECT GAP telephones
Place the DW Pro1/Pro2 headset at a maximum distance of 1 m from the third party base station.
Simultaneously press and hold the headset’s LINK button � and
AUDIO button � for 5 seconds.
The headset switches to setting mode/GAP pairing mode and the
HEADSET LED � flashes blue/red.
Set the third party base station to GAP pairing mode (see the instruction manual of the third party base station).
The headset pairs to the third party base station. If pairing was successful, the HEADSET LED � goes off.
The standard code for DW Pro1/Pro2 is “ 0000 ”.
Pairing is not successful If pairing is not successful within 60 seconds, the DW Pro1/Pro2 headset switches to standby mode.
For information on how to pair the headset to the third party base station, refer to the instruction manual of the base station.
Charging an additional headset
If you wish to charge an additional headset (headset b ) in the base station while you are using your headset (headset a ):
Make sure that a wireless link is established between headset a and base station (the LINK LED � on the base station lights up blue).
Place haedset b into the base station.
Headset a can continue to connect to and disconnect from the base station and its use is not restricted while headset b is being charged.
If you leave the DECT range
If you leave the DECT range during a call, the audio quality deteriorates.
When the link breaks down completely, you hear a descending sequence of beeps in the headset and the LINK LED � on the base station lights up red.
To resume the call:
Re-enter the DECT range of the headset system within 60 seconds.
As soon as the headset re-establishes the wireless link to the base station, you hear a ring tone in the headset.
Press the LINK button � on the headset to resume the call.
If you are using a handset lifter/electronic hook switch or if your softphone supports call control, the call will automatically be ended
60 seconds after leaving the DECT range.
31
Cleaning and maintaining the headset system
Cleaning and maintaining the headset system
CAUTION Damage to the product due to liquids!
Liquids entering the product can short-circuit the electronics or damage the mechanics.
Solvents or cleansing agents can damage the surface of the product.
Keep all liquids far away from the product.
Do not use any solvents or cleansing agents.
Before cleaning, switch the product off and disconnect the base station from the mains.
Only use a dry and soft cloth to clean the product.
Clean the charging contacts of the base station and the charging contacts of the headset from time to time using e.g. a cotton swab.
0
9
Replacing the ear pad(s)
You can replace the ear pad(s). Spare ear pads are available from your
Sennheiser partner.
Carefully remove the old ear pad .
Attach the new ear pad to the ear cup by pressing firmly around the ear pad until you hear it lock into place.
32
8
Cleaning and maintaining the headset system
Replacing the headset’s rechargeable battery
You can replace the rechargeable battery. Spare rechargeable batteries are available from your Sennheiser partner. Only use spare rechargeable batteries recommended by Sennheiser Communications.
CAUTION Damage to the product due to improper handling
The cable connections can be damaged when subjected to mechanical stress.
Open the battery compartment cover and carefully loosen the connector plug of the rechargeable battery.
Pro1 headset
Open the battery compartment cover using your finger nail.
Remove the rechargeable battery and carefully loosen the connector plug of the battery cable.
Insert the connector plug of the new rechargeable battery into the connection socket. Observe correct orientation of the connector plug.
Replace the battery compartment cover onto the headset.
The battery compartment cover locks into place.
Charge the new rechargeable battery (see “Charging the headset rechargeable battery” on page 22).
8
33
Cleaning and maintaining the headset system
Pro2 headset
Carefully remove the ear pad from the ear cup where the battery compartment is located.
Open the battery compartment cover using your finger nail (see first diagram).
Remove the battery compartment cover .
Remove the rechargeable battery and carefully loosen the connector plug of the battery cable.
Insert the connector plug of the new rechargeable battery into the connection socket. Observe correct orientation of the connector plug.
Replace the battery compartment cover onto the ear cup.
The battery compartment cover locks into place.
Reattach the ear pad to the ear cup by pressing firmly around the ear pad until you hear it lock into place.
Charge the new rechargeable battery (see “Charging the headset rechargeable battery” on page 22).
8
9
34
If a problem occurs
If a problem occurs
Problem
The headset is placed into the base station but does not show any reaction
Link between headset and base station cannot be established
(Phone mode)
Link between headset and base station cannot be established
(PC mode)
The headset causes noise and connection losses
Bad radio link between headset and base station
Possible cause
Base station is not connected to the mains
Rechargeable battery is deep discharged
Base station is not connected to the mains
Headset is not paired to the base station
Base station is only connected to the mains
Headset is not paired to the base station
Transmission range is exceeded
Microphone rubs on the cheek or perhaps the beard
Possible solution
Connect the base station to the mains power supply (see page 11).
Wait several minutes until the charging process starts.
Connect the base station to the mains power supply (see page 11).
Pair your headset to the base station
(see page 30).
Connect the base station to the PC using the USB cable (see page 14).
Pair your headset to the base station
(see page 30).
Reduce the distance between headset and base station.
Adjust the radio range (see page 20).
Bend the microphone boom so that the microphone is about 0.8-1.2“ (2-3 cm) away from the corner of the mouth and does not rub on the cheek or beard.
Increase the distance between base station and fixed line phone (see page 14).
The rechargeable battery is quickly depleted even after charging
The sound from the fixed line phone is distorted and disturbed
The other party cannot hear me properly, my voice sounds too low or too loud
Your headset is no longer paired to the base station if an additional headset has been used with the base station
Distance between base station and fixed line phone is so small that interference occurs
Too many DECT systems within the radio range
The rechargeable battery cannot be charged
Charging contacts of the headset or the base station are dirty
Rechargeable battery is defective
Overaged rechargeable battery
Base station is not adjusted to the fixed line phone.
Microphone sensitivity is not correctly adjusted
You can only use the last headset paired to the base station (exception: conference call)
Reduce the radio range (see page 20).
Set the base station to narrowband mode
(see page 21).
Clean the charging contacts on the headset and on the base station (see page 32).
Replace the defective rechargeable battery with a new one (see page 33).
Replace the overaged rechargeable battery with a new one (see page 33).
Adjust the base station to your fixed line phone (see page 18).
Adjust the microphone sensitivity to the
Phone mode (see page 18) or the PC mode
(see page 18).
Replace your headset into the base station
(see page 30).
For additional information and an FAQ list, please visit our website at www.sennheiser.com/DW
If a problem occurs that is not listed in the above table or if the problem cannot be solved with the proposed solutions, please contact your local Sennheiser partner for assistance.
To find a Sennheiser partner in your country, search at www.senncomm.com under “Service & Support”.
35
Accessories and spare parts
Accessories and spare parts
For additional information on accessories and spare parts, please contact your Sennheiser partner or visit our website at www.sennheiser.com.
Accessories
• HSL 10 handset lifter
– mechanical handset lifter
– incl. ring tone detection
– supports nearly all standard desktop telephones
• DHSG cable
– electronic hook switch cable
– for e.g. Siemens, Aastra, etc.
• MSH cable
– electronic hook switch cable
– for e.g. Alcatel, etc.
• Adapter cables for manufacturer specific standards
– available for Cisco, Avaya, Polycom, etc.
Spare parts
• Ear pads (2 pieces)
• Name plate holder
• Windshield
• Rechargeable battery
• Telephone cable
• Micro-USB cable
• Power supply unit, EU version
• Power supply unit, UK version
• Power supply unit, US version
• Power supply unit, AUS version
36
Specifications
Specifications
DW Pro1/Pro2 base station
Dimensions 108 x 116 x 114 mm (W x H x D)
Weight approx.
368 g
Operating temperature range +5°C to +45°C (+41°F to +113°F)
Storage temperature range − 20°C to +70°C (–4°F to +158°F)
DW Pro1/Pro2 headset
Dimensions
Weight
Talk time
Charing time of rechargeable battery
Range
170 x 175 x 55 mm (W x H x D)
Pro1: approx.
65 g
Pro2: approx. 85 g narrowband: up to 12 hours wideband: up to 8 hours
50%:
100%: approx. 20 min approx. 1 hour environment dependent:
• up to 180 m in free line of sight
• up to 55 m in office buildings
Speaker type
Microphone type dynamic, neodymium magnet electret microphone, ultra noise canceling
Operating temperature range +5°C to +45°C (+41°F to +113°F)
Storage temperature range − 20°C to +70°C (–4°F to +158°F)
Type approvals (DW Pro1/Pro2 headset system)
In compliance with
Europe: EMC
Radio
EN 301489-6
EN 301406
Safety
SAR
(headset)
EN 60950-1
EN 50360 ref EN 62209-1
Daily noise exposure Directive 2003/10/EC
USA: This product meets the safety requirements of CSA No. 231437
37
Specifications
Approved by
Canada:
USA:
Industry Canada RSS 213 Issue 2,
RSS 102 Issue 3
IC: 2099D-TDB1 (base station)
IC: 2099D-TDH1 (Pro1 headset)
IC: 2099D-TDH1 (Pro2 headset)
47 CFR Part 15 (d)
FCC ID: DMOCDBDIB (base station)
FCC ID: DMOCDHDFC (Pro1 headset)
FCC ID: DMOCDHDEC (Pro2 headset)
DW Pro1/Pro2 power supply unit
Nominal input voltage
Nominal input current
Mains frequency
Nominal output voltage
100 to 240 V~ max. 0.2 A
50 to 60 Hz
6 V
Nominal output current max. 850 mA
Operating temperature range +5°C to +45°C (+41°F to +113°F)
Storage temperature range
Relative humidity
Weight
− 20°C to +70°C (–4°F to +158°F) operation: 20 to 85% storage: 20 to 95% approx. 75 g
DECT
EU version: CAT IQ 1.0
Transmission frequency 1,880 to 1,900 MHz
SAR value 0,069 W/kg (Pro1 headset)
0,058 W/kg (Pro2 headset)
(max. 10 g SAR)
US version: DECT 6.0
1,920 to 1,930 MHz
0,044 W/kg (Pro1 headset)
0,025 W/kg (Pro2 headset)
(max. 1 g SAR)
38
Manufacturer Declarations
Manufacturer Declarations
Warranty
Sennheiser Communications A/S gives a warranty of 24 months on this product.
For the current warranty conditions, please visit our web site at www.senncom.com or contact your Sennheiser partner.
In compliance with the following requirements
• RoHS Directive (2002/95/EC)
• WEEE Directive (2002/96/EC)
Please dispose of this product at the end of its operational lifetime by taking it to your local collection point or recycling center for such equipment.
• Battery Directive (2006/66/EC)
The supplied rechargeable battery can be recycled. Please dispose of it as special waste or return it to your specialist dealer. In order to protect the environment, only dispose of exhausted rechargeable batteries.
CE Conformity
•
1321
• R&TTE Directive (1999/5/EC)
• EMC Directive (2004/108/EC)
• Low Voltage Directive (2006/95/EC)
The declarations are available at www.sennheiser.com.
Before putting the product into operation, please observe the respective country-specific regulations!
Statements regarding FCC and Industry Canada
This equipment complies with Part 15 of the FCC Rules and with RSS-213 of Industry Canada. Operation is subject to the following two conditions:
(1) this equipment may not cause harmful interference, and (2) this equipment must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
39
Manufacturer Declarations
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This class B digital equipment complies with the Canadian ICES-003
Changes or modifications made to this equipment not expressly approved by Sennheiser electronic Corp. may void the FCC authorization to operate this equipment. Before putting the equipment into operation, please observe the respective country-specific regulations!
The headsets DW 20 HS and DW 30 HS comply with Industry Canada
RF radiation exposure limits for general population. They have been tested for SAR and have complied with the Industry Canada SAR limits for general population.
Trademarks
Sennheiser is a registered trademark of Sennheiser electronic GmbH & Co. KG.
Other product and company names mentioned in this instruction manual may be the trademarks or registered trademarks of their respective owners.
40
Index
Index
A
ABC switch adjusting 18
ACC socket connection of an optional mechanical handset lifter 13
Accessories connection of an optional mechanical handset lifter 13
Acoustic signals adjusting the volume 29
Advanced functions pairing/using additional headsets 30 using 30
Advanced settings adjusting 20 adjusting the radio range 20
DIP switch row 20 establishing the wireless link automatically 21 limiting the volume 21 wideband and narrowband mode 21
Always Audio
27
AUDIO button swapping the assignment 16
Audio signal adjusting 18
Audio volume adjusting 29
B
Base station connection of an optional mechanical handset lifter 13 connection to a fixed line phone 11 connection to a fixed line phone with headset socket 12 connection to a fixed line phone without headset socket 12 connection to a PC 14 connection to an optional electronic hook switch 13 connection to the mains power supply 11 putting into operation 10 removing/attaching the cover 10 setting up 14
Buttons base station 8 headset 8 overview 8
C
Calling accepting an incoming fixed line phone call 25 accepting an incoming PC call 26 ending a fixed line phone call 26 ending a PC call 27 making a fixed line phone call 25 making a PC call 27 transferring a call from the headset to the fixed line phone and vice versa 26 via the fixed line phone 25 via the PC 26
D
DECT 4 leaving the DECT range 31
DECT GAP telephone pairing 31
DHSG connection to an optional electronic hook switch 13
Dial tone adjusting 18
DIP switch 1 and 2 configuring the handset lifter/ hook switch 20
DIP switch 3 adjusting the radio range 20
DIP switch 4 establishing the wireless link 21
DIP switch 5 switching between wideband and narrowband mode 21
DIP switch 6 limiting the volume 21
E
Ear pad(s) replacing 32
G
GAP telephone pairing 31
41
Index
H
Headset adjusting 24 charging 22 labeling 16 overview 7 pairing additional headsets for shared use 30 pairing to third party DECT GAP telephone 31 putting into operation 16 putting on 24
Headset microphone muting 30
Headset system testing the headset system in PC mode and adjusting it 19 testing the headset system in
Phone mode and adjusting it 17
HeadSetup software installing 15 specifications 15
L
LEDs base station 9 headset 9 overview 9
M
Microphone sensitivity adjustment for Phone mode 18
Microphone volume control setting 18
MSH connection to an optional electronic hook switch 13
Muting the headset microphone 30
N
Name plate 16
P
PC connecting the base station to a
PC 14
PC audio reproducing via the headset 27
PC connection testing 19
PC mode adjusting 19 testing 19
Phone and PC mode switching between Phone and PC mode 28
Phone mode adjusting 17 testing 17
Phone socket connecting the base station to a fixed line phone with headset socket 12 connecting the base station to a fixed line phone without headset socket 12
R
Radio range adjusting 20 exceeding 31
Rechargeable battery charging 22 replacing 33
Ring tone adjusting the volume 29
S
Softphone calling via the PC 26 supported softphones 15
Specifications
HeadSetup 15
T
Telephone connection testing 17
Troubleshooting 35
V
Volume adjusting 29 limiting 21
Volume button swapping the assignment 16
W
Wideband and narrowband mode switching between wideband and narrowband mode 21
Wireless link establishing automatically 21
42
Printed in China
Publ. 06/10
A01
Sennheiser Communications A/S
Langager 6, 2680 Solrød Strand, Denmark www.senncom.com
تنزيل
تم تحديث الرابط العام
رابط عام للمستند
إعلان
