SHENZHEN TENDA TECHNOLOGY V7TD305 4Antennas Wireless N300 ADSL2+ Modem Router User Manual

Step 5: Here you can configure the NAT. If you are not an advanced user, the default settings are recommended and then click Next .

Step 6: To configure the Default Gateway interface when using IPv6, select the interface that you want to configure with the WAN gateway address in Selected WAN Interface box. Then click Next .

Step 7: To configure the WAN DNS address, check the Obtain IPv6 DNS info from a WAN interface option, or select the Use the following Static IPv6 DNS address option to enter the static DNS server IPv6 addresses provided by your

ISP. At last, click Next .

76

Step 8: Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set.

When the IPoE connection is successful, you can access the Internet.

 Bridging

If you wish to initiate a dialup directly from your PC for Internet access or enjoy the entire Internet connection (instead of sharing it with others), you can select the Bridging and create a dialup program from your PC.

Step 1: Click Advanced Setup > WAN Service and then click the Add button.

Step 2 : Select the ETH interface you added just now from the pull-down menu in the figure below. Click Next .

Step 3: Select Bridging . Edit the Enter Service Description . This field is optional. It is recommended that you keep the

77

default. And click Next .

Step 4: Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set.

After the bridging connection is successful, initiate a dialup directly from your PC for Internet access.

78

4.2.3 LAN Setup

Here you can configure the LAN IP Address and s ubnet mask. This IP address is to be used to access the device’s settings through a web browser. Be sure to make a note of any changes you apply to this page.

This part includes the following information:



IPv4

 IPv6 Autoconfig

IPv4

IP Address: The device's LAN IP address. The default setting is 192.168.1.1.

Subnet Mask: The LAN subnet mask of the device. Combined with the IP address, the IP Subnet Mask allows a device to know which other addresses are local to it, and which must be reached through a gateway or modem router. You can change the subnet mask to fit your network.

Enable IGMP Snooping : Check to enable the IGMP Snooping. It is recommended to keep the default settings.

Disable DHCP Server: Click to disable the DHCP Server.

Enable DHCP Server: Click to enable the DHCP Server.

Start IP Address: Specify the start of the range for the pool of IP addresses in the same subnet as the router.

End IP Address: Specify the end of the range for the pool of IP addresses in the same subnet as the router.

79

Leased Time: The lease time is a time length that the IP address is assigned to each device before it is refreshed.

Static IP Lease List: Displays a list of devices with reserved static IP addresses.

Add Entries: Click to add a static IP lease entry. A maximum 32 entries can be configured.

Remove Entries: Click to remove a static IP lease entry.

Configure the second IP Address and Subnet Mask for LAN interface: If you want to configure two IP addresses for the LAN interface, you can check this option and enter the second IP Address and Subnet Mask manually.

Apply/Save: After you configure all the needed settings, click this button to apply and save them.

_________________________________________________________________________________________________

TIP

DHCP (Dynamic Host Configuration Protocol) assigns an IP address to each device on the LAN/private network. When you enable the DHCP Server, the DHCP Server will automatically allocate an unused IP address from the IP address pool specified in this screen to the requesting device as long as the device is set to "Obtain an IP Address Automatically". By default, DHCP is enabled.

IPv6 Autoconfig



Static LAN IPv6 Address Configuration

Interface Address (prefix length is required): Enter the interface address.

_________________________________________________________________________________________________

NOTE

1. IPv6 address can only be Aggregatable Global Unicast Addresses and Unique Local Address. Link-Local Unicast

Addresses and Multicast Addresses are not permitted.

2. The IPv6 address must be entered with a prefix length.

_________________________________________________________________________________________________

80



IPv6 LAN Applications

Enable DHCPv6 Server ： Check to enable the DHCPv6 Server.

Stateless: If selected, IPv6 clients will generate IPv6 addresses automatically based on the Prefix Delegation's IPv6 prefix and their own MAC addresses.

Stateful: Stateful DHCPv6 is supported based on the assumption of prefix length less than 64. Select this option and configure the start/end interface ID and leased time. The router will automatically assign IPv6 addresses to IPv6 clients.

Leased Time (hour): The lease time is a time length that the IP address is assigned to each device before it is refreshed.

Start interface ID/End interface ID: Specify the start/end interface ID Interface ID does NOT support ZERO

COMPRESSION "::". Please enter the complete information. For example: Please enter "0:0:0:2" instead of "::2".

Enable RADVD: The RADVD (Router Advertisement Daemon) implements link-local advertisements of IPv6 router addresses and IPv6 routing prefixes using the Neighbor Discovery Protocol (NDP) and is used by system administrators in stateless autoconfiguration methods of network hosts on Internet Protocol version 6 networks. Check the checkbox to enable the RADVD.

Enable ULA Prefix Advertisement: If enabled, the router will advertise ULA prefix periodically

Randomly Generate: If selected, address prefix can be automatically generated.

Statically Configure: If you select this option, you need to manually configure the address prefix and life time.

Prefix: Specify the prefix.

Preferred Life Time (hour): Specify the preferred life time in hour.

Valid Life Time (hour): Specify the valid life time in hour.

Enable MLD Snooping: MLD is used by IPv6 routers for discovering multicast listeners on a directly attached link. If disabled on layer2 devices, IPv6 multicast data packets will be broadcast on the entire layer2; if enabled, these packets will be multicast to only specified recipient instead of being broadcast on the entire layer2.

_________________________________________________________________________________________________

TIP

If you change the LAN IP address of the device, the current connection to the device will be stopped. You must use the new IP address to log in to the device.

Be sure to write the new address on a sticky label and attach it to the bottom of the unit. You will need the new address to log in to the device in the future.

_________________________________________________________________________________________________

81

4.2.4 NAT

This section explains the following:

• Virtual Server

• Port Triggering

• DMZ Host

• UPnP

Virtual Server

The Virtual Server is useful for web servers, ftp servers, e-mail servers, gaming and other specialized Internet applications. When y ou enable the Virtual Server, the communication requests from the Internet to your router’s WAN port will be forwarded to the specified LAN IP address.

To enter the virtual server screen, click NAT > Virtual Server and then click the Add button to add rules.

Use Interface: Select a WAN connection to which you wish to apply the rules. When there is only one WAN connection available, the rules will be automatically applied to it.

Service Name:

- Select a Service: Allows you to select an existing service from the drop-down list.

Custom Service: Allows you to customize a service.

Server IP Address: Enter the IP address of your local computer that will provide this service.

External Starting Port and External Ending Port: These are the starting number and ending number for the public

82

ports at the Internet interface.

Protocol: Select the protocol from the Protocol drop-down list. If you are unsure, select TCP/UDP.

Internal Starting Port and Internal Ending Port: These are the starting number and ending number for the ports of a computer on the router’s local area network (LAN).

_________________________________________________________________________________________________

NOTE

If you have enabled the UPnP functionality on both the router and your PC that is attached to one of the LAN port of the router, you will be prompted on the Virtual Server page that the UPnP interface is being used.

_________________________________________________________________________________________________

Instance

You have set up two servers on your LAN side:

- An FTP server (using the default port number of 21) at the IP address of 192.168.1.100

- A web server (using the default port number of 8080) at the IP address of 192.168.1.110

And want your friends on the Internet to access the FTP server and web server via default ports. To access your FTP or web server from the Internet, a remote user has to know the WAN IP address of your router. In this example, we assume the WAN IP address of your router is 183.37.227.201. Then follow instructions below:

To configure the router to make your local FTP server public:

Procedure

1.

Click NAT > Virtual Server to enter it and then click the Add button.

2.

Select FTP Server that you wish to host on your network from the Select a Service drop-down list. The port number (21) used by this service will then be automatically populated.

- Or if you wish to define the service yourself, enter a descriptive name in the Custom Service, say My FTP, and then manually enter the port number (21) used by this service in the Internal Starting Port, Internal Ending Port,

External Starting Port and External Ending Port fields .

3.

Select a protocol from the Protocol drop-down list. If you are unsure, select TCP/UDP .

4.

In the Server IP Address field, enter the last digit of the IP address of your local computer that offers this service.

Here in this example, we enter 100.

5.

Click .

Your friends on the Internet will then be able to access your FTP server simply by "ftp://183.37.227.201:21".

83

To configure your router to make your local web server public:

Procedure

1.

Click NAT > Virtual Server to enter it and then click the Add button.

2.

Select Web Server (HTTP) that you wish to host on your network from the Select a Service drop-down list. The port number (8080) used by this service will then be automatically populated.

- Or if you wish to define the service yourself, enter a descriptive name in the Custom Service, say My Web Server

(HTTP), and then manually enter the port number (8080) used by this service in the Internal Starting Port,

Internal Ending Port, External Starting Port and External Ending Port fields .

3.

Select a protocol from the Protocol drop-down list. If you are unsure, select TCP/UDP .

4.

In the Server IP Address field, enter the last digit of the IP address of your local computer that offers this service.

Here in this example, we enter 110.

5.

Click .

Now you can view your configurations as seen in the screenshot below. Your friends on the Internet will then be able to access the web server simply by entering "http://183.37.227.201:8080" in his browser.

_________________________________________________________________________________________________

NOTE

1.

The "Internal Port End" cannot be modified directly. Normally, it is set to the same value as "External Port End".

However, if you modify "Internal Port Start", then "Internal Port End" will be set to the same value as "Internal Port

Start".

2.

If the service or game you wish to host on your network is not included in the list, manually add it in the Custom

Service field and then add the port number used by it to the Internal Starting Port, Internal Ending Port, External

Starting Port and External Ending Port fields .

_________________________________________________________________________________________________

84

Port Triggering

Some applications such as games, video conferencing, remote access applications and others require that specific ports in the Router's firewall be opened for access by the applications. Port Trigger dynamically opens up the 'Open Ports' in the firewall when an application on the LAN initiates a TCP/UDP connection to a remote party using the 'Triggering Ports'.

The Router allows the remote party from the WAN side to establish new connections back to the application on the LAN side using the 'Open Ports'.

To enter the Port Triggering screen, click NAT > Port Triggering and then click the Add button to add rules.

You can configure the port settings from this screen by selecting an existing application or creating your own (Custom application) and click Save/Apply to add it.

Use Interface: Select a WAN connection to which you wish to apply the rules. When there is only one WAN connection available, the rules will be automatically applied to it.

Application Name: Two options are available:

Select an application: Select one from the drop-down list directly.

- Custom application: Custom application by yourself.

Trigger Port Start/Trigger Port End: The port range for an application to initiate connections.

Trigger Protocol: Select the protocol from the drop-down list. If you are unsure, select TCP/UDP.

Open Port Start/ Open Port End: These are the starting number and ending number for the ports that will be

85

automatically opened by the built-in firewall when connections initiated by an application are established.

DMZ Host

The default DMZ (De-Militarized Zone) host feature is helpful when you are using some online games and videoconferencing applications that are not compatible with NAT (Network Address Translation).

DMZ Host IP Address: The IP Add ress of the device for which the router’s firewall will be disabled. Be sure to assign a static IP Address to that device. The DMZ host should be connected to a LAN port of the device. Be sure to assign a static IP address to that DMZ host.

Warning!

DMZ servers pose a security risk. A computer designated as the DMZ server loses much of the protection of the firewall and is exposed to exploits from the Internet.

UPnP

UPnP (Universal Plug and Play) allows Windows based systems to configure the device for various Internet applications automatically. UPnP devices can automatically discover the services from other registered UPnP devices on the network.

If you use applications such as multiplayer gaming, peer-to-peer connections, or real-time communications, like instant messaging or remote assistance (a feature in Windows XP), you should enable UPnP.

86

Enable UPnP: Check/uncheck to enable/disable the UPnP feature.

_________________________________________________________________________________________________

NOTE

UPnP is activated only when there is a live WAN service with NAT enabled.

_________________________________________________________________________________________________

4.2.5 Security

This section explains the following information:

• IP Filtering

• MAC Filtering

IP Filtering

Outgoing IP Filtering Setup

By default, all outgoing IP traffic from LAN is allowed, but some IP traffic can be BLOCKED by setting up filters.

Choose Add or Remove to configure outgoing IP filters.

Choose Add to enter the following screen:

87

This screen allows you to create a filter rule to identify outgoing IP traffic by specifying a new filter name and at least one condition below. All of the specified conditions in this filter rule must be satisfied for the rule to take effect. Click to save and activate the filter.



Filter Name: Enter a descriptive filtering name.



IP Version: Support IPv4.



Protocol: TCP/UDP, TCP, UDP and ICMP are available for your option.



Source IP address [/prefix length]: Enter the LAN IP address to be filtered.



Source Port (port or port: port): Specify a port number or a range of ports used by LAN PCs to access the

Internet. If you are unsure, leave it blank.

 Destination IP address [/prefix length]: Specify the external network IP address to be accessed by specified LAN

PCs.

 Destination Port (port or port:port) : Specify a port number or a range of ports used by LAN PCs to access external network.

Incoming IP Filtering Setup

When the firewall is enabled on a WAN or LAN interface, all incoming IP traffic is BLOCKED. However, some IP traffic can be ACCEPTED by setting up filters.

Choose Add or Remove to configure incoming IP filters.

88

Click Add to enter the following screen:

This screen allows you to create a filter rule to identify incoming IP traffic by specifying a new filter name and at least one condition below. All of the specified conditions in this filter rule must be satisfied for the rule to take effect. Click to save and activate the filter.



IP Version: Select IP version.



Protocol: TCP/UDP, TCP, UDP and ICMP are available for your option.

 Source IP address [/prefix length]: Enter the Internal IP address [/prefix length] to be filtered.

 Source Port (port or port: port): Specify a port number or a range of ports used by PCs from external network to access your internal network.

 Destination IP address [/prefix length]: Specify the internal network IP address [/prefix length] to be accessed by the specified PCs from external network.



Destination Port (port or port:port) : Specify a port number or a range of ports used by PCs from external network to access your internal network.

MAC Filtering

A bridge WAN service is needed to configure this service.

MAC Filtering is only effective on ATM PVCs configured in Bridge mode. FORWARDED means that all MAC layer frames will be forwarded except those matching with any of the specified rules in the following table. BLOCKED means that all MAC layer frames will be blocked except those matching with any of the specified rules in the following table.

Choose Add or Remove to configure MAC filtering rules.

89

_________________________________________________________________________________________________

Warning!

Changing from one policy to another of an interface will cause all defined rules for that interface to be REMOVED

AUTOMATICALLY! You will need to create new rules for the new policy.

_________________________________________________________________________________________________


Here you can create a filter to identify the MAC layer frames by specifying at least one condition below. If multiple conditions are specified, all of them take effect. Click Save/Apply to save and activate the filter.

Protocol Type: Select a protocol type from the drop-down list.

Destination MAC Address: Enter the MAC address of data frame being restricted to arrive.

Source MAC Address: Enter the MAC address of data frame being restricted to come.

Frame Direction: Select a frame direction from the drop-down list.

WAN Interfaces: Select a WAN interface from the drop-down list.

4.2.6 Parental Control


90

• Time Restriction

• URL Filter

Time Restriction

Click Parental Control > Time Restriction > Add to enter the following screen.

Here you can add time of day restriction that an attached LAN device can access the Internet.

The Browser's MAC Address automatically displays the MAC address of the LAN device where the browser is running.

To restrict other LAN device, check the "Other MAC Address" option and enter its MAC address.



User Name: Enter a user name.



Browser's MAC Address: Automatically adds the MAC address of the attached LAN device where the browser is running.

 Other MAC Address: Specify the MAC address of the computer that you want to apply Internet access restriction.

 Days of the week: Click to select the days of the week during which you wish to restrict Internet access.

 Start Blocking Time/ End Blocking Time: Specify time of day restriction to an attached LAN device. Within this specified time length of the day, this LAN device will be blocked from the Internet.

 Apply/Save: Click to save and apply your settings.

URL Filter

Here you can add URL access restriction to specific LAN PCs.

91

Select the URL List Type (Exclude or Include) first and then click Add to enter the screen below for configuring the list entries.

URL Address: Enter a specific URL or a key word of domain name in this field.

Click to apply and save the settings.

_________________________________________________________________________________________________

NOTE

If you have accessed the URL before you include it in a URL filter rule, you must reboot the router and erase it from your PC to activate this URL filter rule. To erase the domain name from your PC:

1.

Click the keys +R on the keyboard to enable “Run” dialog

, and type cmd > click OK .

( Note that different operati on systems may have different ways to enable “Run”; Windows is taken a guide here.)

92

2.

Then type ipconfig /flushdns and hit Enter on the keyboard.

_________________________________________________________________________________________________

4.2.7 Bandwidth Control

When multiple devices each of which requests a different bandwidth attach to the modem router, to ensure the attached devices obtaining a fair bandwidth and getting a fluent Internet experience, set a bandwidth control rule.

Check Enable Bandwidth Control to enable this feature.

93

Description : Name the bandwidth control rule as you like.

IP Address Range : Type the IP address range of target hosts. Follow the example

If you want to set one host, follow the example .

Max Upstream Speed (Kbps): Set the upstream speed as your actual bandwidth need.

Max Downstream Speed (Kbps) : Set the downstream speed as your actual bandwidth need.

Status : Enable or Disable.

first to save and then click After you have edited the details of the bandwidth control rule, click activate the settings.

4.2.8 Routing


• Default Gateway

• Static Route

Default Gateway

.

to

Default gateway interface list can have multiple WAN interfaces served as system default gateways but only one will be used according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is connected. Priority order can be changed by removing all and adding them back in again.



Selected Default Gateway Interfaces: Displays the selected default gateway interfaces. Select a WAN interface and click the button to move it to the Available Routed WAN Interfaces box.

94



Available Routed WAN Interfaces: Displays the available routed WAN interfaces. Select a WAN interface and click the button to add it to the Selected Default Gateway Interfaces box.



Apply/Save: Click to save and activate your settings.

Static Route

Static routes provide additional routing information to your router. Typically, you do not need to add static routes.

However, when there are several routers in the network, you may want to set up static routing. Static routing determines the path of the data in your network. You can use this feature to allow users on different IP domains to access the Internet via this device. It is not recommended to use this setting unless you are familiar with static routing. In most cases, dynamic routing is recommended, because this feature allows the router to detect the physical changes of the network layout automatically.




IP Version: Select IP version.



Destination IP address/prefix length: Enter the destination IP address and prefix length of the final destination.



Interface: Select an interface from the drop-down list.



Gateway IP address: Enter the gateway IP address, which must be a router on the same LAN segment as the

95

router.



Metric: Enter a number in the Metric field. This stands for the number of routers between your network and the destination.



Apply /Save: Click to apply and save your settings.

_________________________________________________________________________________________________

NOTE

1. Destination IP address cannot be on the same IP segment as WAN or LAN segment as the router.

2. Only configure additional static routes for unusual cases such as multiple routers or multiple IP subnets located on your network. Wrong static routes may lead to network failure.

3. For system created route, the

“Remove”

checkbox is disabled.

_________________________________________________________________________________________________

4.2.9 DNS

DNS Server (Static DNS)

The DNS server translates domain names to numeric IP addresses. It is used to look up site addresses based on their names. If the DNS server works incorrectly, Internet access will be blocked.

DNS server is configured when you are setting up your Internet connectivity. So, you do not have to finish DNS server setup here unless your network works false.

For IPv4

① Click Advanced Setup > DNS > DNS Server , and enter the screen below.

96

② Check the Select DNS Server Interface from available WAN interfaces option if the device gets a DNS address automatically from an upstream device.

Or select the Use the following Static DNS IP address option and enter static DNS server address provided by your ISP.

③ Click Apply/Save at the bottom of the page.

For IPv6

① Click Advanced Setup > DNS > DNS Server , and enter the screen below.

② Select the Obtain IPv6 DNS info from a WAN interface option if the device gets a DNS server address from the upstream device automatically. And select a configured WAN interface for the IPv6 DNS server information.

Or select the Use the following Static IPv6 DNS address option and enter the static IPv6 DNS server address provided by your ISP.

③ Click Apply/Save .

NOTE

1.

In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses must be entered.

2.

If you are not clear about the static DNS server IP information, ask your ISP to provide it.

3.

The default settings are recommended if you are unsure about the DNS server addresses. If a wrong DNS server address is configured, webpages may not be open.

Dynamic DNS (DDNS)

If your Internet service provider (ISP) gave you a static (fixed) public IP address, you can register a domain name and have that name associated with your IP address by public Domain Name Servers (DNS). However, if your ISP gave you a dynamic (changing) public IP address, you cannot predict what your IP address will be, and the address can change frequently. In this case, you can use a commercial Dynamic DNS service. It allows you to register your domain to their

IP address and forward traffic directed at your domain to your frequently changing IP address. If your ISP assigns a private WAN IP address (such as 192.168.x.x or 10.x.x.x), the Dynamic DNS service does not work because private

97

addresses are not routed on the Internet.

Click Advanced Setup > DNS > Dynamic DNS to enter the Dynamic DNS screen.

Click to configure the DDNS settings.

D-DNS Provider: Select your DDNS service provider from the drop-down menu.

Hostname: Enter the DDNS domain name registered with your DDNS service provider.

Interface: Specify a WAN connection interface.

Username: Enter the DDNS user name registered with your DDNS service provider.

Password: Enter the DDNS Password registered with your DDNS service provider.

Click to save your settings.

Example: dyn.com

Hostname: tenda.dyndns.org

Username: tenda

Password: 123456789

Add Dynamic DNS

① Select dyn.com from the D-DNS provider drop-down menu.

98

② Enter the hostname. Here is

“ tenda.dyndns.org

”

for example.

③ Specify a WAN connection interface.

DynDNS Settings

④ Enter your DynDNS username. Here is

“ tenda

” for example.

⑤ Enter the password of DynDNS account.

Here is

“

123456789

” for example.

⑥ Click to save your configuration.

4.2.10 DSL

This screen provides multiple ASDL modulation modes to meet diversified environments. You can also select phone line pair and Capability.

DSL parameter configurations must be supported by ISP to take effect. Actual parameters (see Statistics-DSL ) resulted from the negotiation between your router and ISP. Wrong configurations may fail your Internet access.

The best DSL configurations are the factory defaults. Only change them with the support of your ISP or our technical staff when your router fails to negotiate with ISP in DSL (ATM) mode.

99

Check the checkbox next to a modulation to enable it and then click

Advanced Settings: Click it to enter the Advanced Settings screen as below.

.

Here you can select the test mode and tone.

_________________________________________________________________________________________________

TIP

If you are unsure about the DSL parameters, please apply the factory default settings. Wrong configurations may fail your Internet access.

_________________________________________________________________________________________________

4.2.11 Storage Service


• Storage Device Info

• User Account

The modem router provides a USB port. You can attach a USB storage device to it and share your USB device with a user in the LAN.

Storage Device Info

Once you plug your USB storage device into the USB port, the details about the USB storage will be recorded shown as below table.

100

and then uplug your USB device. Removing directly may damage your USB storage device. Click

User Account

Accessing the USB storage device requires an account. You can click to use the default account or you can customize a new one. Pay attention to that your computer system will record the account you used at the first time.

Application: How to access the USB storage device attached to the modem router?

Step 1 : Plug USB storage device.

Plug your USB storage device into the USB port, and make sure the USB LED indicator is on.

Step 2 : Create an account.

Go to User Account interface, and set up your account. Here the default account “samba” is kept. And click

101

to save and apply.

Step 3 : Access the USB storage device from a computer.

Click

Click OK .

+R on the keyboard to pop up the Run dialog, and type \\192.168.1.1

in the blank field.

Step 4

: Access the USB storage device with the account “samba”.

Double click

, and enter your account “samba” and password to finish the credentials. Then, click

OK .

102

Access successfully!

4.2.12 Interface Grouping

Interface Grouping supports multiple ports to PVC and bridging groups. Each group will perform as an independent network. To support this feature, you must create mapping groups with appropriate LAN and WAN interfaces using the

Add button. The Remove button will remove the grouping and add the ungrouped interfaces to the Default group.

103

Click Add to enter the screen below:

 Group Name: Define a name for group.

 WAN Interface used in the grouping: WAN connection to which the interface grouping rules apply.

 Available LAN Interfaces: LAN interfaces which are available for interface grouping.

 Grouped LAN Interfaces: LAN interfaces which are classed into the specified WAN connection.

To create a new interface group:

① Enter the Group name and the group name must be unique.

② Select an available WAN interface for the LAN network proxy.

③ Define the available LAN interface to connect to the specified WAN interface.

Select interfaces from the

Available LAN Interfaces list and add it to the Grouped LAN Interfaces list using the arrow buttons to create the required mapping of the ports.

④ Click Apply/Save button to make the changes effective immediately.

If you

want to by pass NAT via the router

’ s interface and obtain the public IP address automatically, you need to add the

DHCP vendor ID in the Automatically Add Clients with the following DHCP Vendor IDs section. After the ID takes effect, your router will automatically detect the DHCP request from computers on the LAN, and it will forward the

DHCP vendor ID and the corresponding DHCP request to the WAN interface used in the interface rules.

NOTE

1.

Eth0, eth1, eth2 and eth3 respectively represent 1/WAN, 2, 3 and 4/iTV port of the device. And wlan0 is the port for all wireless devices connecting to the modem router.

2.

If a vendor ID is configured for a specific client device, please REBOOT the client device attached to the modem to allow it to obtain an appropriate IP address.

3.

No Interface/None indicates that there is no WAN port.

104

4.2.13 IP Tunnel


• IPv6inIPv4

• IPv4inIPv6

IPv6inIPv4

Click IPv6inIPv4 and Add to enter the following screen:



Tunnel Name: Specify the name of the tunnel.



Mechanism: Currently, only 6RD configuration is supported.



Associated WAN Interface: Specify the WAN interface of the tunnel.



Associated LAN Interface: Specify the LAN interface of the tunnel.



Manual: If you select Manual, configure the following settings also:

 IPv4 Mask Length: Specify the IPv4 Mask Length.



6rd Prefix with Prefix Length: Specify the 6rd Prefix with Prefix Length.



Border Relay IPv4 Address: Specify the Border Relay IPv4 Address.



Automatic: If Automatic is selected, no configurations are required.



Apply/Save: Click to apply and save your settings.

105

IPv4inIPv6

Click IPv4inIPv6 and Add to enter the following screen:



Tunnel Name: Specify the name of the tunnel.



Mechanism: Currently, only DS-Lite configuration is supported.



Associated WAN Interface: Specify the WAN interface of the tunnel.

 Associated LAN Interface: Specify the LAN interface of the tunnel.

 Manual: If you select Manual, enter the AFTR information also:

 Automatic: If Automatic is selected, no configurations are required.

 Apply/Save: Click to apply and save your settings.

4.2.14 Certificate


• Local Certificates

• Trusted CA (Certificate Authority) Certificates

Local Certificates

Here you can add, view or remove certificates. Local certificates are used by peers to verify your identity. Maximum 4

106

certificates can be stored.

To generate a certificate signing request:

① Click the Create Certificate Request button to enter the page below.

② Specify the Common Name, Organization Name and State/Province Name

③ Enter the 2-letter Country Code for the certificate.

④ Click Apply to apply your settings.

To Import certificate ：

① Click the Import Certificate button on the local certificates page to enter the page below.

107

② Enter the certificate name.

③ Paste the certificate content and private key.


Trusted CA (Certificate Authority) Certificates

Here you can add, view or remove CA certificates. CA certificates are used by you to verify peers' certificates. Maximum

4 certificates can be stored.

108

To Import certificate ：

① Click the Import Certificate button to enter the page below.

② Enter the certificate name.

③ Paste the certificate content.


4.2.15 Multicast

Here you can configure the multicast feature.

To configure IGMP for IPv4

① Check the LAN to LAN (Intra LAN) Multicast Enable box.

② Check the Membership Join Immediate (IPTV) box. This is only required for IPTV.

③ Keep other options unchanged from factory defaults if you are not an advanced user. This is strongly recommended.

109

To configure IGMP for IPv6

① Check the LAN to LAN (Intra LAN) Multicast Enable box.

② Keep other options unchanged from factory defaults if you are not an advanced user. This is strongly recommended.

110

4.2.16 IPTV

If you check the Enable IPTV checkbox, you must choose a layer2 interface, and then configure the PVC info (ATM), or VLAN info (ETH). Click to save it.

Enable IPTV: Check to enable the IPTV service, or disable it.

IPTV configuration for DSL Internet Access user:

① Enable IPTV .

② Select Layer2 interface: ATM Interface .

③ Configure an available VPI/VCI value which should be provided by your ISP.

④ Click .

IPTV configuration for Ethernet Internet Access user:

① Enable IPTV .

② Select Layer2 Interface: ETH Interface .

③ Click .

111

After successful IPTV configurations, Port 4/iTV on the back panel of the device can only be an IPTV port.

_________________________________________________________________________________________________

TIP

For tagged service, enter valid 802.1P Priority and 802.1Q VLAN ID.

For untagged service, set -1 to both 802.1P Priority and 802.1Q VLAN ID.

_________________________________________________________________________________________________

4.3 Wireless


• Basic

• Security

• MAC Filter

• Wireless Bridge

• Station Info

4.3.1 Basic

This page allows you to configure basic features of the wireless LAN interface. You can enable or disable the wireless

LAN interface, hide the network from active scans, set the wireless network name (also known as SSID) and restrict the channel set based on country requirements.

Click to configure the basic wireless options.

112

 Enable Wireless: check/uncheck to enable/disable the wireless feature.

 Hide Access Point (Hide SSID): This option allows you to have your network names (SSID) publicly broadcast. If you choose to enable it, the SSID will be hidden.



SSID: This is the public name of your WiFi.



BSSID: Display the MAC address of the wireless network.



Country: Select your country.

 Channel: Select a channel, or select Auto to let system automatically select one for your wireless network to operate on if you are unsure. The best selection is a channel that is the least used by adjacent networks.

 Bandwidth: Configure the wireless bandwidth. The default is 40MHz.

 RF Power: Normal or Enhance. This option may adjust the wireless signal strength.

4.3.2 Security

This page allows you to configure security features of the wireless LAN interface. You may set up configuration manually or through WiFi Protected Setup (WPS).

113

WPS Setup

Wi-Fi Protected Setup makes it easy for home users who know little of wireless security to establish a home network, as well as to add new devices to an existing network without entering long passphrases or configuring complicated settings.

Enable WPS : This is WPS ON/OFF turn. Click it to enable or disable WPS. WPS is disabled by default.

Device PIN: This is PIN code of the modem router for WPS PIN mode.

Enter SAT PIN :

“SAT” means the remote wireless client requiring a connection. Enter its PIN code in the blank if you select this option, and then click .

Use AP PIN :

“AP” means

the modem router. Select this option if you copy the PIN code of the modem router to the remote wireless client.

NOTE

1.

WPS/RST button in the device back panel : When WPS feature is enabled, press this button on the device for 1~3 seconds and the WPS LED will keep blinking for about 2 minutes. Within the 2 minutes, press the WPS button on your wireless clients. When the WPS displays a solid light, the wireless client has joined in your wireless network.

2.

To use the WPS security, the wireless client must be also WPS-capable.

3.

WPS only supports WPA2, which means only when you select “WPA2” encryption or “Open” you can change WPS status.

114

Manual Setup AP

You can set the network authentication method, selecting data encryption, specify whether a network key is required to authenticate to this wireless network and specify the encryption strength.

Click when done.



Network Authentication: Select Open, Shared, WPA-PSK, WPA2-PSK or Mixed WPA/ WPA2-PSK from the drop-down list to encrypt your wireless network.

Depending on the type of network authentication you select, you will be prompted to enter corresponding settings.

 WEP Encryption: Select Enabled or Disabled.

 Encryption Strength: Select 128-bit or 64-bit.

 Current Network Key: Select a network key to be active.



Network Key 1/2/3/4: Enter 13 ASCII characters or 26 hexadecimal digits for 128-bit encryption keys; enter 5

ASCII characters or 10 hexadecimal digits for 64-bit encryption keys.



WPA/WAPI passphrase: Enter a WPA/WAPI network key.



WPA Group Rekey Interval: Specify a key update interval.

 WPA/WAPI Encryption: Select AES or TKIP+AES.

115

4.3.3 MAC Filter

The MAC-based Wireless Access Control feature can be used to allow or disallow clients to connect to your wireless network.

MAC Restrict Mode: Disabled, Allow and Deny

 Allow: Only allow PCs at specified MAC addresses (in the list) to connect to your wireless network.

 Deny: Block only PCs at specified MAC addresses from connecting to your wireless network.

 Disable: Disable this feature.

Add: Click it to add a MAC address.

Remove: To delete an existing MAC address, first check the Remove box next to the MAC address in list and then click this button.

Example 1: To allow only the PC at the MAC address of 00:1A:3D:9C:BB:23 to connect to your wireless network, do as follows:

① Select Allow , and click .

② Click the Add button.

116

③ Enter 00:1A:3D:9C:BB:23 in the MAC address box as shown in the figure below, and click

Set up successfully!

________________________________________________________________________________________________

NOTE

If

“

Allow

”

mode is activated with no MAC address being limited, WPS feature will be disabled. Go to Wireless >

Security to check WPS status).

________________________________________________________________________________________________

4.3.4 Wireless Bridge

This page allows you to configure wireless bridge (also known as Wireless Distribution System) features of the wireless interface.

Wireless distribution system (WDS) is a system enabling the wireless interconnection of access points in an IEEE 802.11 network. It allows a wireless network to be expanded using multiple access points without the traditional requirement for a wired backbone to link them.

117

AP Mode: You can select Wireless Bridge (also known as Wireless Distribution System) to disable access point functionality. Selecting Access Point enables access point functionality. Wireless bridge functionality will still be available and wireless stations will be able to associate to the AP.

Bridge Action: There are three options available: Enabled , Enabled (Scan) and Disabled . Disabled mode means disabling the wireless bridge function. If Enabled mode is selected, you need to enter the remote device MAC address manually. If Enabled (Scan) is selected, the system automatically scans the remote device MAC address and SSID.

Remote Bridges MAC Address: Here displays the remote device info, MAC address and SSID (if Bridge Action is

Enabled Scan ), or offers you field to enter the remote info, MAC address (if Bridge Action is Enabled ).

Refresh: Click to refresh the Wireless Name (SSID). Wait for few seconds to refresh.

Apply/Save: Click to apply and save the settings.

Instance

Assume that there is a wireless router in your living room, far away from your study room. Every time you join the WiFi in the study room, it seems hard for you to watch a high-quality live streaming video. To add another wireless router in the study room is an ideal choice to solve your problem. Wireless Bridge function of the modem router helps you to extend your wireless coverage, speed up downloading. Then your video will run smoother and faster.

Assume that the router in your living room is Router 1 , and the other one in study room is Router 2 .

118

Before you get started:

① View and note down the security settings of Router 1: wireless name (SSID), channel, security mode, MAC address and wireless key. a) Click Advanced > Wireless > Basic to check the SSID , MAC address ( BSSID ) and Channel .

SSID: Tenda_112252

BSSID: 00:90:4C:11:22:53

Channel: 6 b) Click Advanced > Wireless > Security to check security mode and wireless key.

119

WPS: Disable

Security Mode: WPA2-PSK / AES

Wireless Key: 12345678

② View the LAN settings of Router 1.

Click Advanced > Advanced Setup > LAN to check LAN IP address and Subnet Mask, and verify that the DHCP

Server is enabled.

LAN IP Address: 192.168.1.1;

Subnet Mask: 255.255.255.0

120

After you prepare two steps above, do as follows:

Configure Router 2:

① Set the LAN IP address of Router 2 to a different IP address yet on the same segment as Router 1.



Click Advanced > Advanced Setup > LAN to change the LAN IP address into 192.168.1.10.



Disable your DHCP server.

② Click Advanced > Wireless > Basic to check the SSID and Channel. They should be the same as Router 1

’ s. If not, correct them manually. Click Apply/Save to save your settings.

③ Click Advanced > Wireless > Security to check the security mode and wireless key. Verify that they are the same as Router 1

’s. If not, correct them manually. Click

Apply/Save to save your settings.

④ Click Advanced > Wireless > Wireless Bridge to configure wireless bridge.

 Access Point (Recommended):

Two ways to bridge Router 1 by using Access Point : a.

If you select Enable in Bridge Action field.

121



Enter the MAC address of Router 1 which you have noted down (00:90:4C:11:22:53).



Then click Apply/Save to save the settings. b.

If you select Enable(Scan) in Bridge Action field.



Select the SSID of Router 1 (Tenda_112252) in Remote Bridges MAC Address field.



If you cannot find the SSID on the list, click Refresh to refresh the list.



Then click Apply/Save to save your settings.



Wireless Bridge

Two ways to bridge Router 1 by using Wireless Bridge : a.

If you select Enable in Bridge Action field.



Enter the MAC address of Router 1 which you have noted down (00:90:4C:11:22:53).



Then click Apply/Save to save the settings.

122

b.

If you select Enable(Scan) in Bridge Action field:



Select the SSID of Router 1 (Tenda_112252) in Remote Bridges MAC Address field. If you cannot find the

SSID on the list, click Refresh to refresh the list.




After you fininsh the settings on Router 2 above, do as follows:

Configure Router 1:

① Click Advanced > Wireless > Wireless Bridge .

② Select Access Point in AP Mode field. (If you select Wireless Bridge here, the wireless devices will not be able to connect Router 1 wirelessly.)

If AP Mode of Router 2 is Access Point , there are two ways to bridge Router 2. a.

If you select Enable in Bridge Action field:



Enter the MAC address of Router 2 which you can check on Wireless > Basic interface, say BSSID

(02:10:18:01:00:02).

123



Then click Apply/Save to save the settings. b. If you select Enable(Scan) in Bridge Action field:



Select the SSID of Router 2 (Tenda_112252) in Remote Bridges MAC Address field.



If you cannot find the SSID on the list, click Refresh to refresh the list.




The configuration is finished. Then the devices can connect Router 2 wirelessly or via Ethernet cables.

If AP Mode of Router 2 is Wireless Bridge , you can only select Enable and enter the MAC address (02:10:18:01:00:02) to bridge Router 2.

124

The configuration is finished. Then the devices can only connect Router 2 via Ethernet cables.

NOTE

The WDS feature (also known as Wireless Bridge) can only be implemented between 2 WDS-capable wireless devices.

Plus, SSID, channel, security settings and security key must be exactly the same on both such devices.

4.3.5 Station Info

This page shows authenticated wireless stations and their status.

4.4

Diagnostics

this part includes the following information:

 Diagnostics

 Ping test

125

4.4.1 Diagnostics

The device is capable of testing the connection to your DSL service provider, the connection to your Internet service provider and the connection to your local network. If a test displays a fail status, click

“

Rerun Diagnostic Tests

”

at the bottom of this page to make sure the fail status is consistent. If the test continues to fail, click

“

Help

”

and follow the troubleshooting procedures.

Pass: Indicates that the Ethernet interface from your computer is connected to the LAN port of the device.

Fail: Indicates that the device does not detect the Ethernet interface on your computer.

4.4.2 Ping test

Ping utility can help test whether the device has built a proper connection with your host.

Type in the IP address of your host in the Ping IP Address field, and click Ping . If you get a similar screen shown as below, it indicates the connection between the Ping object (Here is 192.168.1.2) and the device has been established.

126

4.5 Management


• Settings

• System Logs

• SNMP Agent

• TR-069 Client

• Internet Time

• Access Control

• Update Software

• Reboot

4.5.1 Settings


• Backup

• Restore Backup

• Restore Default

Backup

Here you can save a copy of your device’s configurations to your computer. Once you have configured the device, you can save these settings to a configuration file on your local hard drive. The configuration file can later be imported to your device in case the device is reset to factory default settings.

127

Restore Backup

Here you can restore the configurations of the modem router from a file saved on your PC.

Restore Default

Under some circumstances (for example, join a different network or unfortunately forgetting the login password), you may need to remove the existing configuration and restore the factory default settings.

4.5.2 System Logs

The System Log dialog allows you to view the system log and configure the system log options.

128

To configure the system log, click Configure System Log .

 Log: If Enable is selected, the system will begin to log all the selected events.

 Log Level: Set the log level. All events above or equal to the selected level will be logged.

 Display Level: Set the log display level. All logged events above or equal to the selected level will be displayed.



Apply/Save: click to apply and save the system log settings.

To view the system log, firstly ensure log is enabled, otherwise you cannot read any log.

4.5.3 SNMP Agent

Simple Network Management Protocol (SNMP) allows a management application to retrieve statistics and status from the SNMP agent in this device.

129



SNMP Agent ： Select “Enable” to activate the SNMP Agent feature or “Disable” to deactivate it.



Read Community: Specify a Read Community string. The default is public.



Set Community: Specify a Set Community string. The default is private.



System Name: Specify a descriptive system name.



System Location: Specify a system location.



System Contact: Specify a system contact.



Trap Manager IP: Specify the IP address of the Trap Manager.

4.5.4 TR-069 Client

WAN Management Protocol (TR-069) allows an Auto-Configuration Server (ACS) to perform auto-configuration, provision, collection, and diagnostics to this device.

Click the TR-069 Client tab to enter the TR-069 Client configuration screen as seen below:

130

 Inform: Select Enable/Disable to enable/disable the TR-069 Client function. By default, it is disabled.

 Inform Interval: Specify the inform interval.



ACS URL: Enter the ACS (Auto-Configuration Server) URL address.



ACS User Name: Enter the ACS (Auto-Configuration Server) user name.



ACS Password: Enter the ACS (Auto-Configuration Server) password.



WAN Interface used by TR-069 client: Select the WAN interface used by the TR-069 client from the drop-down list.

 Display SOAP messages on serial console: If Enable is selected, SOAP messages will be displayed on serial console; if Disable is selected, SOAP messages will not be displayed on serial console.

 Connection Request Authentication: Check/uncheck to enable/disable the connection request authentication.

 Connection Request User Name: Enter the connection request user name.



Connection Request Password: Enter the connection request password.



Connection Request URL: Specify the connection request URL.

4.5.5 Internet Time

This page is used to set the router’s system time. If

Automatically synchronize with Internet time servers is checked, the system will automatically connect to NTP server to synchronize the time.

First/Second/Third/Fourth/Fifth NTP time server: Select a NTP time server from the drop-down list. If the NTP time server you are looking for is not inc luded in the list, select “Other” and then enter it manually in the box.

Time zone offset: Select your time zone from the drop-down list.

131

4.5.6 Access Control


• Password

• AccessControl - Service

Password

Access to your broadband router is controlled through two user accounts: admin and support.

Admin has unrestricted access to change and view configuration of your Broadband Router.

Support is used to allow a professional technician to access your Broadband Router for maintenance and to run diagnostics.

User Name: Enter the user name of up to 16 characters.

The default is “admin”.

Old Password: Enter the old password of up to 16 characters.

The default is “admin”.

New Password: Enter a new password of up to 16 characters.

Confirm Password: Re-enter to confirm the new password.

Apply/Save: Click to change or create passwords.

_________________________________________________________________________________________________

NOTE

Password cannot contain a space.

_________________________________________________________________________________________________

132

Access Control - Service

Here you can manage the device either from LAN or WAN side using HTTP, ICMP, TELNET, SNMP, FTP, TFTP and

HTTPS.

_________________________________________________________________________________________________

NOTE

If you are not an advanced user, it is recommended to keep the default settings.

________________________________________________________________________________________________

4.5.7 Update Software

Firmware upgrade is released periodically to improve the functionality of your device and add any new features. If you run into a problem with a specific feature of the device you could log in to our website ( www.tendacn.com

) to download the latest firmware to update your device.

133

This modem router supports three types to update firmware.

Type 1: General Update

To update software, do as follows:

① Obtain an updated software image file from our website: www.tendacn.com

.

134

② Click the "Browse" button to locate the firmware file.

③ Click to start updating.

Type 2: Updating Via FTP Server

Updating via FTP server is supported. Make sure there is an available FTP server.

① Type the FTP Server IP address, like the right figure

② Type the port the FTP server used.

③ Type the user name and password to access the FTP server.

④ Copy the name of the firmware.

⑤ Click to start updating.

Type 3: Updating Via TFTP Server

Updating via TFTP server is supported. Make sure there is an available TFTP server.

① Type the TFTP Server IP address in the field.

② Copy the name of the firmware.

③ Click to start updating.

135

NOTE

The update process will cost 2 minutes, and the device will reboot.

4.5.8 Reboot

Click the Reboot button to reboot the router.

136

Appendix 1 Applications

Application 1: How to change SSID and wireless password?

① Go to Wireless > Basic interface.

② Specify a SSID as you like, like Tenda_myhome .

③ Click Apply/Save to save the settings.

④ Go to Wireless > Security interface.

⑤ Choose a network authentication (WPA2-PSK is recommended) and set a passphrase.

⑥ Click Apply/Save to save the settings.

137

Application 2: How to reset the modem router?

The device supports two methods to reset to factory defaults. Note that after you reset the device, you should reconfigure it for Internet service.

Method 1: WPS/RST button

Press the WPS/RST button on the back of the modem router for about 8 seconds to reset it to factory defaults.

Method 2: Restore Default Settings from User Interface

① Go to Management > Settings > Restore Default to enter the interface below.

② Click icon to start resetting.

And wait for the processing bar completing…

138

Appendix 2 Configure Your PC

This part is just for your references when your computer connecting to the modem router cannot get an IP address.

Screens to configure TCP/IP properties in other Operating Systems are similar to those below.

Windows 8

1.

Right click the icon or on the bottom right corner of your desktop.

TIP : If you cannot find the icon or , go to Control Panel and find

Network and Internet .

2.

Click Open Network and Sharing Center .

3.

Click Ethernet > Properties .

139

4.

Find and double click Internet Protocol Version

4(TCP/IPv4) .

5.

Select Obtain an IP address automatically and Obtain

DNS server address automatically and click OK .

6.

Click OK on the Ethernet Properties window (see Step 4 for the screenshot).

140

Windows 7

1.

Click the icon on the bottom right corner of your desktop.

2.

Click Open Network and Sharing Center .

3.

Click Local Area Connection >

Properties .

4.

Find and double click Internet Protocol Version

4(TCP/IPv4) .

141

5.

Select Obtain an IP address automatically and Obtain

DNS server address automatically and click OK .

6.

Click OK on the Local Area Connection Properties window (see Step 4 for the screenshot).

142

MAC

1.

Click on the Apple icon from the top-left corner and select System

Preferences .

2.

Click Network .

3.

Click on Ethernet .

4.

Select Using DHCP .

5.

Click Apply .

143

Appendix 3 Join Your Wireless Network

Windows 8

1.


TIP:

1. If you cannot find the icon , please move your mouse to the top right corner of your desktop, select Settings > Control Panel > Network and Internet > Network and Sharing Center >

Change adapter settings , right click Wi-Fi and select Connect/Disconnect .

2. If you cannot find your wireless network from the list, ensure the Airplane Mode is not enabled on your PC.

2.

Select your wireless network from the list, click Connect and then follow onscreen instructions.

3.

When your wireless network is connected successfully, the following screen will appear.

144

Windows 7

1.


2.

Double click your SSID (wireless network name) and then follow onscreen instructions.

3.

When your SSID (wireless network name) displays Connected as shown below, you’ve connected to it for Internet access successfully.

145

MAC

1.

Click > System Preferences .

2.

Select Network from Internet & Network .

3.

Click WiFi .

4.

Turn WiFi on.

5.

Click No network selected .

6.

Select the wireless network name of your router.

7.

Enter the wireless password and click Join .

146

iPhone/iPad

1.

Scroll screen to find the Settings icon and click it.

2.

Click WiFi, and turn on WiFi.

3.

Find the name of the wireless network you wish to connect, and click it.

4.

Enter the wireless password and click Join .

Connected successfully!

147

Appendix 4 FAQs

1. What information should I have to access the Internet via the DSL uplink?

If you have DSL broadband service, you might need the following information to set up your modem router.

• Active I nternet service provided by a DSL account

• The ISP configuration informat ion for your DSL account

- ISP login name and password

- Fixed or static IP address

Depending on how your ISP set up your Internet account, you could need to know the Virtual path identifier (VPI) and virtual channel identifier (VCI) parameters for a manual setup.

2. I cannot access the device's User Interface (UI). What should I do?

1) Verify the physical connection (namely, the Ethernet cable) between your PC and the modem router. For details, see

Chapter 2 Hardware Installation hereof.

2)

Double check the TCP/IP settings on your PC. For details, see Appendix 2 Configure Your PC hereof.

3) Press the WPS/RST button on the device for about 8 seconds and then re-access the UI with the default login info

“admin”

.

4) Change the Ethernet cable that connects your PC and the device.

5) Try accessing device management interface from other PCs, smart phones or iPads.

6) Connect your PC alone to one of the LAN ports on the device.

3. What can I do if I forget my password?

1) If you forgot your login password, restore the device to its factory default settings and then use the default User

Name “admin” and Password “admin” to log in.

2) If you forgot your wireless network password, log in to the device User Interface, and go to Wireless > Security to check or change your password.

4. Why cannot I connect to the searched wireless network?

1) Verify that you entered a correct security key.

2) Log in to the device, select Advanced > Wireless and change the wireless network name (SSID). Then connect again.

3) Log in to the device, select Advanced > Wireless > Security and change the security settings. Then connect again.

148

Appendix 5 VPI/VCI List

Australia

Australia

Australia

Australia

Australia

Argentina

Argentina

Argentina

Belgium

Belgium

Belgium

Belgium

Bolivia

Brazil

Brazil

The following table lists common ISPs and their VPI and VCI numbers. If you cannot locate your ISP and their VPI and

VCI information here, ask your ISP to provide it.

Country

Australia

ISP

Telstra

VPI

8

VCI

35

Encapsulation

PPPoA LLC

Australia

Australia

Australia

GoldenIT

Telstra Bigpond

OptusNET

8

8

8

35 PPPOA_VCMUX

35 PPPOE_LLC

35 PPPOE_VCMUX

Australia

Australia

Australia

Australia

Australia

Australia

Australia

AAPT

ADSL Direct

Ausie Broadband

Australia On Line

Connexus

Dodo

Gotalk

8

8

8

8

8

8

8

35

35

35

35

35

PPPOE_VCMUX

PPPOE_LLC

PPPOE_LLC

PPPOA_VCMUX

PPPOE_LLC

35 PPPOE_LLC

35 PPPOE_VCMUX

Internode iPrimus

Netspace

Southern Cross Telco

TPG Internet

Telecom

Telefonica

ADSL Office

Turboline

Turboline

ADSL Office

Brasil Telcom

Telefonica

8

8

8

8

8

0

8

1

8

8

8

8

0

0

8

35

35

35

35

35

33

35

33

35

35

35

35

PPPOE_VCMUX

PPPOA_VCMUX

PPPOE_VCMUX

PPPOE_LLC

PPPOE_LLC

PPPoE LLC

PPPoE LLC

PPPoA VC-MUX

1483 Routed IP LLC

PPPoA LLC

1483 Bridged IP LLC

35 1483 Bridged IP LLC

34 1483 Routed IP LLC

35 PPPoE LLC

PPPoE LLC

149

TE-data

Linkdsl

Vodafone

Saunalahti

Elisa

DNA

Sonera

Free

Orange

SFR

ISP

Telmar

South Region

Primus Canada

Rogers Canada (1)

Rogers Canada (2)

Rogers Canada (3)

BellSouth(1) Canada

BellSouth(2) Canada

Sprint (1) Canada

Sprint (2) Canada

Verizon (1) Canada

Verizon (2) Canada

EMCALI

ETB

ICE

Cybercity, Tiscali

Country

Brazil

Brazil

Canada

Canada

Canada

Canada

Canada

Canada

Canada

Canada

Canada

Finland

Finland

France

France (1)

France (2)

France (3)

Germany

Canada

Colombia

Columbia

Costa Rica

Czech Republic

Denmark

Dominican Republic

Dubai

Egypt:

Egypt:

Egypt:

Finland

Finland

8

8

1

8

8

0

0

0

0

0

0

8

0

0

0

1

8

0

0

0

8

0

8

0

0

8

0

VPI VCI Encapsulation

0 33 PPPoE LLC

1

0

0

32 PPPoE LLC

35 PPPoE LLC

35 PPPoE LLC

35

35

35

35

35

1483 Bridged IP LLC

1484 Bridged IP LLC

PPPoE LLC

PPPoE LLC

PPPoA LLC

35 PPPoE LLC

35 PPPoE LLC


33 PPPoA VC-MUX

33 PPPoE LLC



35 PPPoA VC-MUX










36 LLC

35 PPPoE LLC

67 PPPoE LLC

35 PPPoA VC-MUX

32 PPPoE LLC

150

Country

Hungary

Iceland

Iceland

India

India

India

India

Iran

Iran

Iran

Iran (1)

Iran (2)

Iran

Israel

Iran

Iran

Iran

Iran

Iran

Iran

India

India

Indonesia Speedy

Telkomnet

Iran

Iran

Iran

Iran

ISP

Sci-Network

Islandssimi

Siminn

Airtel

BSNL

MTNL

RELIANCE

COMMUNICATION

TATA INDICOM

CONNECT

[Shatel]

Aria-Rasaneh-Tadbir

Asia-Tech

Pars-Online (Tehran)

Pars-Online (Provinces)

[Saba-Net]

Neda-Gostar-Saba

Pishgaman-Tose

Fan-Ava

Datak

Laser (General)

Laser (Privates)

Asr-Enteghal-Dadeha

Kara-Amin-Ertebat

ITC

Dadegostar Asre Novin

0

1

8


0 35 PPPoE LLC

0

8

1

0

0

35 PPPoA VC-MUX

48 PPPoA VC-MUX


35

35

1483 Bridged IP LLC

1483 Bridged IP LLC

0 35 PPPOE LLC

32 PPPOE LLC

32 PPPOE LLC

81 PPPoE LLC

0

0

0

0

8

0

8

0

0

0

0

0

8

0

8

0

0

35 PPPOE LLC

35 PPPOE LLC

35 PPPOE LLC

59 PPPOE LLC

35 PPPOE LLC

35 PPPOE LLC

35 PPPOE LLC

35 PPPOE LLC

35 PPPOE LLC

32 PPPOE LLC

35 PPPOE LLC

33 PPPOE LLC

35 PPPOE LLC

35 PPPoE LLC

81 PPPoE LLC

33 PPPOE LLC

35 PPPoA VC-MUX

151

Country

Israel(1)

Italy

Italy

Jamaica (1)

Jamaica (2)

Jamaica (3)

Jamaica (4)

ISP

Kazakhtelecom

Kazakhstan

«Megaline»

Kazakhstan kuwait unitednetwork

Malaysia

Malaysia

Streamyx

Mexico

Mexico

Mexico

Mexico morocco

Netherlands

Telmex (1)

Telmex (2)

Telmex (3)

Telmex (4)

IAM

BBNED

Netherlands

Netherlands

Netherlands

New Zealand

MXSTREAM

BBNED

MX Stream

Xtra

New Zealand Slingshot

Orange Nyumbani

(Kenya)

Pakistan (PALESTINE)

Pakistan for PTCL

Pakistan (cyber net)

Pakistan (linkDotnet)

Pakistan(PTCL)

0

8

0


8 48 PPPoA VC-MUX

8

8

8


35 PPPoA VC-MUX

35 PPPoA VC-MUX

35 PPPoA VC-MUX

35 1483 Bridged IP LLC SNAP

35 1483 Bridged IP LLC SNAP

0 40 LLC/SNAP Bridging

8

0

0

8

0

0

0

0

8

0

8

0

8

0

0

0

33 PPPoA VC-MUX


35 PPPOE LLC

35 PPPoE LLC

81 PPPoE LLC

35 PPPoE LLC

81 PPPoE LLC

35 PPPoE LLC

35 PPPOE

35 PPPoA VC-MUX



48 PPPoA VC-MUX

35 PPPoA VC-MUX

100 PPPoA VC-MUX

35 PPPoE LLC

8

0

8

0

8



35 PPPoE LLC

35 PPPoA LLC

81 PPPoE LLc

152

Spain

Spain

Spain

Spain

Spain

Spain

Spain

Spain

Spain

Country

Philippines(1)

Philippines(2)

ISP

Portugal

Puerto Rico Coqui.net

RomTelecom Romania:

Russia

Russia

Rostel

Port telecom

Russia

Saudi Arabia (1)

Saudi Arabia (2)

Saudi Arabia (3)

Saudi Arabia (4)

Saudi Arabia (5)

Saudi Arabia (6)

Spain

VNTC

Arrakis

Auna Spain

Spain

Spain

Spain

Spain

Comunitel

Eresmas

Jazztel

Jazztel ADSL2+/

Desagregado

OpenforYou

Tele2

Telefónica (España)

Albura, Tiscali

Colt Telecom, Ola Internet

EresMas, Retevision

Telefonica (1)

Telefonica (2), Terra

Wanadoo (1)

8

0

8

8

0

8

0

0

0

0

0

0

0

0

0


0 35 1483 Bridged IP LLC

0

0

0


35 PPPoE LLC

35 PPPoA LLC

35

35

35

35

33

1483 Bridged IP LLC

PPPoE LLC

PPPoE LLC

PPPoE LLC

PPPoE LLC

35 PPPoE LLC


33

35

35

35

1483 Routed IP LLC

1483 Bridged IP LLC

1483 Routed IP LLC

1483 Bridged IP VC-MUX

35 1483 Bridged IP VC-MUX



35 IPOE VC-MUX

8

8

8

8

1

0

8

8

8

8

35

32

1483 Bridged IP LLC-BRIDGING



32 1483 Bridged IP LLC/SNAP

32 PPPoA VC-MUX

35 PPPoA VC-MUX

35 PPPoA VC-MUX

32 PPPoE LLC


35 PPPoA VC-MUX

153

Country

Spain

Spain

Spain

Spain

Spain

Spain

Spain

Spain

Spain

Spain

SpainWanadoo

Sri Lanka

Telecom-(SLT)

Sweden Telenordia

Sweden

Switzerland

Telefónica (Perú)

Telia

Switzerland

Telefónica (Argentina)

Thailand

Thailand

Thailand

Thailand

Thailand

Trinidad & Tobago

Turkey (1)

Turkey (2)

UAE (Al sahmil)

United States

United States

United States

TRUE

TOT

3BB

Cat Telecom

BuddyBB

TSTT

4DV.Net

All Tel (1)

All Tel (2)

ISP

Wanadoo (2)

Terra

Terra

Uni2

Orange

Orange 20 Megas

Orange

Ya.com

Ya.com

Wanadoo (3)

8

8

8

8

8

8

8


8 32 PPPoE LLC

8

8

1




35

35

32

32

32


LLC-BRIDGING

1483 Bridged IP LLC/SNAP

1483 Bridged IP VC - MUX




8

0

0

8

8

0

0

0

0

0

0

0

1

8

8

8

8

8

8

35 PPPOE LLC

35 PPPoE



35 PPPoE LLC

35 1483 Bridged IP LLC-based


100 PPPoE LLC

32 PPPoE LLC

33 PPPoE LLC

35 PPPoE LLC

35 PPPoE LLC

35 PPPoA VC-MUX

35 PPPoE LLC

35 PPPoA VC-MUX


32 PPPoA VC-MUX

35 PPPoE LLC


154

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

Country

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

ISP

Ameritech

AT&T (1)

AT&T (2)

AT&T (3)

August.net (1)

August.net (2)

BellSouth

Casstle.Net

CenturyTel (1)

CenturyTel (2)

Coqui.net

QWest (1)

QWest (2)

QWest (3)

QWest (4)

SBC (1)

SBC (2)

SBC (3)

Covad

Earthlink (1)

Earthlink (2)

Earthlink (3)

Earthlink (4)

Eastex

Embarq

Frontier

Grande ommunications

GWI

Hotwire

Internet Junction

PVT

0

0

8

0

0

0

0

1

0

8

0

0

0

0

8

8

0

0

0

0

8

0

0

8

8

8

0


8 35 PPPoA LLC

0

8

0

35 PPPoE LLC



35

35

35

96

35

1483 Bridged IP LLC

1483 Bridged IP LLC

PPPoE LLC

1483 Bridged IP LLC

PPPoE LLC


35 PPPoA LLC

35 PPPoE LLC

35 PPPoE LLC

35 PPPoE LLC

35 PPPoE VC-MUX

32 PPPoA LLC

100 PPPoA LLC


35 PPPoE LLC

34 PPPoE LLC





32 PPPoALLC

32 PPPoA VC-MUX


32 PPPoE LLC

35 PPPoE LLC



155

Country

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United Kingdom (1)

United Kingdom (2)

United Kingdom

United Kingdom

UK

Uzbekistan

Uzbekistan

Uzbekistan

Venezuela

Vietnam

Vietnam

Vietnam

Vietnam

Verizon (2)

Windstream

Verizon (2)

AOL

Karoo

Sharq Stream

Sarkor

TShTT

CANTV

VDC

Viettel

FPT

ISP

Sonic

SouthWestern Bell

Sprint (1)

Sprint (2)

Sprint Territory

SureWest

Communications(1)

SureWest

Communications(2)

SureWest

Communications(3)

Toast.Net

Uniserv

US West

Verizon (1)



0

0

8

0


35 PPPoALLC

35 PPPoE LLC

35 PPPoE LLC

0 34 1483 Bridged LLC Snap

0 32 PPPoE LLC

0

0

0

8

0

0

8

8

0

0

0

1

0

0

0

0

0

0

0

0

0

32 PPPoA LLC

35 PPPoE LLC


32 PPPoA VC-MUX

35 PPPoE LLC


35 PPPoE LLC


38 PPPoA VC-MUX

38 PPPoE LLC

38 PPPoE VC-MUX

50 PPPoA LLC


35 PPPoE LLC

33 PPPoE LLC

35 PPPoE LLC


35 PPPoE LLC

35 PPPoE LLC

35 PPPoE LLC

33 PPPoE LLC

156

Brazil

Brazil

Brazil

Brazil

Canada

Canada

Canada

Australia

Australia

Australia

Australia

Australia

Argentina

Argentina

Argentina

Belgium

Belgium

Belgium

Belgium

Bolivia

Country

Australia

Australia

Australia

Australia

Australia

Australia

Australia

Australia

Australia

Australia

Australia

ISP

Telstra

GoldenIT

Telstra Bigpond

OptusNET

AAPT

ADSL Direct

Ausie Broadband

Australia On Line

Connexus

Dodo

Gotalk

Internode iPrimus

Netspace

Southern Cross Telco

TPG Internet

Telecom

Telefonica

ADSL Office

Turboline

Turboline

ADSL Office

Brasil Telcom

Telefonica

Telmar

South Region

Primus Canada

Rogers Canada (1)

Rogers Canada (2)

0

0

8

0

1

0

8

8

8

8

1

8

8

0

8

8

8

0

8

8

8

8

8

8

8

8

8


8 35 PPPoA LLC

8

8

8

35 _PPPOA_VCMUX

35 PPPOE_LLC

35 PPPOE_VCMUX

35

35

35

35

35

PPPOE_VCMUX

PPPOE_LLC

PPPOE_LLC

PPPOA_VCMUX

PPPOE_LLC

35 PPPOE_LLC

35 PPPOE_VCMUX

35 PPPOE_VCMUX

35 PPPOA_VCMUX

35 PPPOE_VCMUX

35 PPPOE_LLC

35 PPPOE_LLC

33 PPPoE LLC

35 PPPoE LLC

33 PPPoA VC-MUX


35 PPPoA LLC




35 PPPoE LLC

35 PPPoE LLC

33 PPPoE LLC

32 PPPoE LLC

35 PPPoE LLC

35 PPPoE LLC


157

ISP

Rogers Canada (3)

BellSouth(1) Canada

BellSouth(2) Canada

Sprint (1) Canada

Sprint (2) Canada

Verizon (1) Canada

Verizon (2) Canada

EMCALI

ETB

ICE

Cybercity, Tiscali

TE-data

Linkdsl

Vodafone

Saunalahti

Elisa

DNA

Sonera

Free

Orange

SFR

Sci-Network

Islandssimi

Siminn

Airtel

BSNL

Country

Canada

Canada

Canada

Canada

Canada

Canada

Canada

Colombia

Columbia

Costa Rica

Czech Republic

France (3)

Germany

Hungary

Iceland

Iceland

India

India

Denmark

Dominican Republic

Dubai

Egypt:

Egypt:

Egypt:

Finland

Finland

Finland

Finland

France

France (1)

France (2)

8

1

0

0

0

8

1

0

0

0

0

8

8

8

0

0

0

8

0

0

0

0

8

0

0

1

8



8

0

0

35 PPPoE LLC

35 PPPoE LLC

35 PPPoA LLC

35

35

35

33

33

PPPoE LLC

PPPoE LLC

1483 Bridged IP LLC

PPPoA VC-MUX

PPPoE LLC



35 PPPoA VC-MUX










36 LLC

35 PPPoE LLC

67 PPPoE LLC

35 PPPoA VC-MUX

32 PPPoE LLC

35 PPPoE LLC

35 PPPoA VC-MUX

48 PPPoA VC-MUX



158

Iran

Iran

Iran

Iran

Iran

Iran

Iran

Iran

Iran

Iran

Iran

Iran

Iran

Iran (1)

Iran (2)

Iran

Israel

Israel(1)

Italy

Italy

Jamaica (1)

Jamaica (2)

Country

India

India

India

India

Indonesia Speedy

Telkomnet

ISP

MTNL

RELIANCE

COMMUNICATION

TATA INDICOM

CONNECT

[Shatel]

Aria-Rasaneh-Tadbir

Asia-Tech

Pars-Online (Tehran)

Pars-Online (Provinces)

[Saba-Net]

Neda-Gostar-Saba

Pishgaman-Tose

Fan-Ava

Datak

Laser (General)

Laser (Privates)

Asr-Enteghal-Dadeha

Kara-Amin-Ertebat

ITC

Dadegostar Asre Novin

0

1

8



0 35 PPPOE LLC

32

32

81

PPPOE LLC

PPPOE LLC

PPPoE LLC

35 PPPOE LLC

35 PPPOE LLC

35 PPPOE LLC

59 PPPOE LLC

35 PPPOE LLC

35 PPPOE LLC

35 PPPOE LLC

35 PPPOE LLC

35 PPPOE LLC

32 PPPOE LLC

35 PPPOE LLC

33 PPPOE LLC

35 PPPOE LLC

35 PPPoE LLC

81 PPPoE LLC

33 PPPOE LLC

35 PPPoA VC-MUX

48 PPPoA VC-MUX


35 PPPoA VC-MUX

35 PPPoA VC-MUX

35 PPPoA VC-MUX

0

0

0

0

0

0

0

0

8

0

8

0

0

8

0

0

8

8

8

0

8

8

159

Country

Jamaica (3)

Jamaica (4)

Malaysia

Malaysia

ISP

Kazakhtelecom

Kazakhstan

«Megaline»

Kazakhstan kuwait unitednetwork

Streamyx

Mexico

Mexico

Mexico

Mexico

Telmex (1)

Telmex (2)

Telmex (3)

Telmex (4) morocco

Netherlands

Netherlands

Netherlands

IAM

BBNED

MXSTREAM

BBNED

Netherlands

New Zealand

New Zealand

MX Stream

Xtra

Slingshot

Orange Nyumbani

(Kenya)

Pakistan (PALESTINE)

Pakistan for PTCL

Pakistan (cyber net)

Pakistan (linkDotnet)

Pakistan(PTCL)

Philippines(1)

Philippines(2)

Portugal

Puerto Rico Coqui.net

RomTelecom Romania:


8 35 1483 Bridged IP LLC SNAP

0 35 1483 Bridged IP LLC SNAP

0 40 LLC/SNAP Bridging

8

0

8

0

8

0

0

8

8

0

0

0

0

0

0

33 PPPoA VC-MUX


35 PPPOE LLC

35 PPPoE LLC

81 PPPoE LLC

35 PPPoE LLC

81 PPPoE LLC

35 PPPoE LLC

35 PPPOE

35 PPPoA VC-MUX



48 PPPoA VC-MUX

35 PPPoA VC-MUX

100 PPPoA VC-MUX

0

8

0

8

0

8

0

0

0

0

0

35 PPPoE LLC



35 PPPoE LLC

35 PPPoA LLC

81 PPPoE LLc



35 PPPoE LLC

35 PPPoA LLC


160

Spain

Spain

Spain

Spain

Spain

Spain

Spain

Spain

Spain

Spain

Spain

Spain

Spain

Spain

Spain

Country

Russia

Russia

Russia

Saudi Arabia (1)

Saudi Arabia (2)

Saudi Arabia (3)

Saudi Arabia (4)

Saudi Arabia (5)

Saudi Arabia (6)

Spain

Spain

Spain

Spain

Spain

ISP

Rostel

Port telecom

VNTC

Arrakis

Auna

Comunitel

Eresmas

Jazztel

Jazztel ADSL2+ /

Desagregado

OpenforYou

Tele2

Telefónica (España)

Albura, Tiscali

Colt Telecom, Ola Internet

EresMas, Retevision

Telefonica (1)

Telefonica (2), Terra

Wanadoo (1)

Wanadoo (2)

Terra

Terra

Uni2

Orange

8

0

8

8

0

0

0

0

0

0


0 35 PPPoE LLC

0

8

0

35 PPPoE LLC

35 PPPoE LLC

33 PPPoE LLC

35

33

33

35

35

35

PPPoE LLC

1483 Bridged IP LLC

1483 Routed IP LLC

1483 Bridged IP LLC

1483 Routed IP LLC





35 IPOE VC-MUX

8

8

8

8

1

0

8

8

8

8

8

8

8

1

8

35

32

35

32

32

35

35

32

32

35

32

32

32

33

35

1483 Bridged IP LLC-BRIDGING




PPPoA VC-MUX

PPPoA VC-MUX

PPPoA VC-MUX

PPPoE LLC

1483 Routed IP LLC

PPPoA VC-MUX

PPPoE LLC





161

Country

Spain

Spain

Spain

Spain

ISP

Orange 20 Megas

Orange

Ya.com

Ya.com

Wanadoo (3) Spain

SpainWanadoo

Sri Lanka

Telecom-(SLT)

Sweden Telenordia

Sweden

Switzerland

Telefónica (Perú)

Telia

Switzerland

Telefónica (Argentina)

Thailand

Thailand

TRUE

TOT

Thailand

Thailand

Thailand

Trinidad & Tobago

Turkey (1)

Turkey (2)

UAE (Al sahmil)

United States

United States

3BB

Cat Telecom

BuddyBB

TSTT

4DV.Net

All Tel (1)

United States

United States

United States

United States

United States

United States

All Tel (2)

Ameritech

AT&T (1)

AT&T (2)

AT&T (3)

August.net (1)


8 35 LLC-BRIDGING

8

8

8

8

8


32 1483 Bridged IP VC - MUX


32

32

1483 Routed IP LLC

1483 Bridged IP LLC

8 35 PPPOE LLC

0

1

8

8

0

0

0

8

8

8

8

8

0

0

0

0

8

0

8

0

8

0

0

35 PPPoE



35 PPPoE LLC

35 1483 Bridged IP LLC-based


100 PPPoE LLC

32 PPPoE LLC

33 PPPoE LLC

35 PPPoE LLC

35 PPPoE LLC

35 PPPoA VC-MUX

35 PPPoE LLC

35 PPPoA VC-MUX


32 PPPoA VC-MUX

35 PPPoE LLC


35 PPPoA LLC

35 PPPoE LLC




162

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

Country

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

ISP

August.net (2)

BellSouth

Casstle.Net

CenturyTel (1)

CenturyTel (2)

Coqui.net

Covad

Earthlink (1)

Earthlink (2)

Earthlink (3)

Earthlink (4)

Eastex

Embarq

Frontier

Grande ommunications

GWI

Hotwire

Internet Junction

PVT

QWest (1)

QWest (2)

QWest (3)

QWest (4)

SBC (1)

SBC (2)

SBC (3)

Sonic

SouthWestern Bell

Sprint (1)

Sprint (2)

Sprint Territory

0

8

0

0

0

0

8

0

0

0

0

0

0

0

0

1

0

0

0

8

0

0

8

0

8

8

0



8

0

8

35 PPPoE LLC


35 PPPoE LLC

35

35

35

35

35

1483 Bridged IP LLC

PPPoA LLC

PPPoE LLC

PPPoE LLC

PPPoE LLC

35 PPPoE VC-MUX

32 PPPoA LLC

100 PPPoA LLC


35 PPPoE LLC

34 PPPoE LLC





32 PPPoALLC

32 PPPoA VC-MUX


32 PPPoE LLC

35 PPPoE LLC





35 PPPoALLC

35 PPPoE LLC

35 PPPoE LLC

163

Country

United States

United States

United States

United States

United States

United States

United States

United States

United States

United States

United Kingdom (1)

United Kingdom (2)

United Kingdom

United Kingdom

UK

Uzbekistan

Uzbekistan

Uzbekistan

Venezuela

Vietnam

Vietnam

Vietnam

Vietnam

ISP

SureWest

Communications(1)

SureWest

Communications(2)

SureWest

Communications(3)

Toast.Net

Uniserv

US West

Verizon (1)

Verizon (2)

Windstream

Verizon (2)

AOL

Karoo

Sharq Stream

Sarkor

TShTT

CANTV

VDC

Viettel

FPT


0 34 1483 Bridged LLC Snap

0 32 PPPoE LLC

0

0

0

0

0

0

8

0

1

8

8

0

0

0

0

0

0

0

0

0

0

32 PPPoA LLC

35 PPPoE LLC


32 PPPoA VC-MUX

35 PPPoE LLC


35 PPPoE LLC


38 PPPoA VC-MUX

38 PPPoE LLC

38 PPPoE VC-MUX

50 PPPoA LLC


35 PPPoE LLC

33 PPPoE LLC

35 PPPoE LLC


35 PPPoE LLC

35 PPPoE LLC

35 PPPoE LLC

33 PPPoE LLC

164

Appendix 6 Regulatory Compliance

Information

CE Mark Warning

This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

— Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.

Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

165

SHENZHEN TENDA TECHNOLOGY V7TD305 4Antennas Wireless N300 ADSL2+ Modem Router User Manual

IPv4

IPv6 Autoconfig

Static LAN IPv6 Address Configuration

IPv6 LAN Applications

Virtual Server

Procedure

Procedure

Port Triggering

DMZ Host

UPnP

IP Filtering

MAC Filtering

Time Restriction

URL Filter

Default Gateway

Static Route

DNS Server (Static DNS)

Dynamic DNS (DDNS)

Storage Device Info

User Account

Application: How to access the USB storage device attached to the modem router?

IPv6inIPv4

IPv4inIPv6

Local Certificates

Trusted CA (Certificate Authority) Certificates

4.3 Wireless

Instance

Before you get started:

After you prepare two steps above, do as follows:

After you fininsh the settings on Router 2 above, do as follows:

4.4

Diagnostics

4.4.1 Diagnostics

4.4.2 Ping test

4.5 Management

Backup

Restore Backup

Restore Default

Password

Access Control - Service

Type 1: General Update

Type 2: Updating Via FTP Server

Type 3: Updating Via TFTP Server

Appendix 1 Applications

Application 1: How to change SSID and wireless password?

Application 2: How to reset the modem router?

Method 1: WPS/RST button

Method 2: Restore Default Settings from User Interface

Appendix 2 Configure Your PC

Windows 8

Windows 7

MAC

Appendix 3 Join Your Wireless Network

Windows 8

Windows 7

MAC

iPhone/iPad

Appendix 4 FAQs

Appendix 5 VPI/VCI List

Appendix 6 Regulatory Compliance

Information

Related manuals

Billion Electric

QI3BIL-7800VNOX

Billion

BiPAC 8800AXL

Cisco

RV-120W

BEC

8920NE

Billion

BiPAC 8800NL R2

BEC

7700N

Billion

BiPAC 7700N R5

TP-LINK

TL-R480T+

TP-LINK