BSA Bantam DI 125 c.c., D7 175 c.c. motorcycle Instruction Manual
PDF
Dokument
Reklama
Reklama
Instruction Manua
Models
DI 125 c.c. Bantam
D7 175 c.c. Bantam Super
Instruction Manual
for
D Models
B.S.A. MOTOR CYCLES LTD., ARMOURY ROAD,
BIRMINGHAM, 11
Telephone: VICtoria 2381. Telegrams “SELMOTO,” Birmingham.
SERVICE, SPARES AND REPAIRS DEPARTMENT
Telegrams “SELSERV,” Birmingham.
B.S.A. Motor Cycles Ltd. reserve the right to alter the designs or any con»
structional details of their manufactures at any time without giving notice.
Printed in England Copyright B.S.A. Co. Ltd. MC 1344-74-10
This Instruction Manual is intended to acquaint
the B.S.A. owner with details of the controls,
general maintenance and technical data which
may be required for normal operation of the
machine.
It does not contain the information necessary
to carry out complete stripping for major over-
hauls, but if any owner feels competent to carry
out this type of work a service manual wall chart,
and an illustrated spares catalogue for this machine
can be obtained from his B.S.A. spares stockist
or local dealer.
Owners in the British Isles can obtain these
publications direct from B.S.A. Motor Cycles Ltd.,
Service Department, Waverley Works, Birmingham
10. The service manual is priced at seven shillings
and sixpence, plus sixpence postage, and the spares
catalogue is five shillings and sixpence, plus six-
pence postage. Always quote full engine and frame
numbers when ordering these publications.
TT)
SPEEDOMETER B® LIGHTING SWITCH
CLUTCH LEVER Ix FRONT BRAKE
DIPPER
SWITCH THROTTLE TWIST GRIP
(Battery set) (Open in direction of arrow)
THE CONTROLS MODEL D 7
LIGHTING SWITCH HORN BUTTON
(Battery set)
SPEEDOMETER
FRONT BRAKE
CLUTCH LEVER
и
= A
OL о
o © © o
—
@ J
THROTTLE
DIPPER SWITCH | = TWIST GRIP
FILLER CAP (Open in direction
of arrow)
FOOT
GEAR CHANGE
REAR BRAKE
=
=
- x.
—
-
CHANGE ©
DOWN
KICKSTARTER
STRANGLER
Fig. 1. The Controls Model D.1.
Controls for D7 similar, except where shown in inset.
3
PETROL TAP
CONTENTS
AIR CLEANER
BRAKES
CARBURETTER
FRONT CHAIN
REAR CHAIN
CLEANING
CLUTCH
CONTROLS .. .. .. ..
CYLINDER HEAD AND BARREL REMOVAL
DRIVING
DECARBONISING |
ELECTRICAL EQUIPMENT
FORKS
GEARBOX ..
HUBS..
IGNITION TIMING
LUBRICATION CHART
LUBRICATION SYSTEM
PERIODICAL MAINTENANCE
REAR SUSPENSION
RUNNING-IN
SPARES STOCKISTS
SPARKING PLUG
STEERING HEAD
TECHNICAL DATA
TRANSMISSION
WHEEL REMOVAL (FRONT) ..
WHEEL REMOVAL (REAR)
WIRING DIAGRAM (DIRECT LIGHTING SET).
WIRING DIAGRAM (BATTERY SET)
pages
20
27
18
20
26
10
23
13
s 12
30
27
25
25
11
21-22
11
10
29-30
37
16
28
20
25
25
34
35-36
TECHNICAL DATA
Engine Number—on top of crankcase below cylinder.
Frame Number—at top of steering head tube.
Engine:
Capacity. .
Cylinder bore
Stroke
Compression ratio
Piston ring gap ..
Sparking plug
Plug points gap
Transmission:
Gear ratios:
Clutch—friction plates. .
Chain size and pitch front
$ х ‹ 250 т...
rear $ х - 305 in.
Teeth on: engine sprocket
gearbox sprocket
clutch sprocket
rear chainwheel
Capacities :
Fuel tank
Petroil mixture ..
Gearbox
Front forks
Wheels:
Rim size
Tyre size
Tyre pressure
Brake size
minimum
maximum
minimum
maximum
top ..
second ..
first
Model Dl
123 с.с.
52 mm.
58 mm.
6-5—1
-009 in.
-013 in.
L7
-018 in.
-020 in.
7-0
11.7
22-0
3
50
117
17
15
38
47
13 gallons
See page 21
3 pint
—
. front WMI—19
. rear
. front
rear
. front
rear
. dia.
wide
5
WM1—19
2-75—19
2-75—19
16 p.s.i.
22 p.s.i.
5 in.
$ in.
Model D7
174 c.c.
61-5 mm.
58 mm,
7-4—1
+009 in.
-013 in.
L7
-018 in.
-020 in.
6-58
11-0
20-65
3
50
121
17
16
38
47
2 gallons
See page 21
3 pint
4 pint each
leg
WM1—18
WM1—18
3-00—18
3-00—18
16 p.s.i.
24 p.s.i.
54 in.
1 in.
TECHNICAL DATA
Carburation: Amal
Bore
Main jet
Pilot jet
Throttle valve
Needle position. .
Needle jet
Air cleaner
General Details:
Front suspension movement ..
Rear suspension movement
Generator output
Contact breaker gap
Battery capacity
(battery lighting) ..
Overall length
Wheelbase
Ground Clearance
Saddle height
Overall height
Handlebar width
Steering head angle
Steering lock angle
Model D1
tin.
75
5
2
-106
Amal.
33 in.
2 in.
30 watts
«015 in.
8 amp. hour
77 in,
SO in.
4% in.
27 in.
38% in.
264 in.
61°
45°
Model D7
+ in.
140
25
375/34
2
* 1055
Ата!.
3 in.
23 in.
30 watts
-015 in.
8 amp. hour
794 in.
51 in.
54 in.
31 in.
36 in.
272 in.
61°
45°
** The recommended tyre pressures are based on a rider’s weight of 140
Ibs. If the rider is heavier, increase the pressures as follows :—
Front tyre: Add one lb. per sq. in. for every 28 1b. increase above
140 1b.
Rear tyre: Add one lb. per sq. in. for every 14 Ib. increase above
140 Ib.
If additional load is carried in the form of a pillion passenger or lug-
gage, the actual load bearing upon each tyre should be determined
and the pressures increased in accordance with the Dunlop Load and
Pressure Schedule.
TAKING OVER THE MACHINE
Before running the machine make sure that the fuel tank contains the correct
mixture of oil and petrol, that the gearbox is properly topped up with oil and
that the battery (when fitted) is filled and charged. (See appropriate chapters
for filling instructions.) Normally these preparations will be carried out by the
dealer who is selling the machine and the new owner has only to arrange the
controls to his liking and the machine is ready for the road.
The Controls.
The new rider should make sure that he is quite familiar with all the controls
before attempting to ride the machine. Most of the controls are adjustable and
should be positioned so that they can be reached without moving the hands
from the grips or the feet from the footrests. Handlebars should be adjusted
so that a comfortable and natural riding position is achieved. Make sure that
the bolts retaining the handlebar clamps are tight after completing any adjust-
ment. Badly positioned controls cause poor control of the machine and will
bring discomfort on long journeys.
HANDLEBAR CONTROLS
Twist Grip.
Mounted on the right handlebar it controls the throttle opening. To open
the throttle (i.e. to increase the engine speed) turn the grip so that the top moves
towards the rider. Full movement is about a quarter of a turn.
Front Brake.
Hand lever mounted on the right handlebar in front of the twist grip. Squeeze
the lever towards the bar to operate the brake.
Clutch
Hand lever mounted on the left handlebar in front of the grip. Squeeze the
lever towards the bar to free the clutch, i.e. disengage the drive between the
engine and the rear wheel.
Horn (Battery Equipment)
The horn button is mounted on the right handlebar on top of the front brake
lever bracket (D1). The model D7 horn button is combined with the dipper
switch in a single housing adjacent to the grip on the left handlebar,
Headlamp Dipper Switch
This is mounted on the left handlebar and controls the switching from main
to dipped beam. It is a separate unit clipped to the bar (D1). On the D7, the
dipper switch is combined with the horn button in a single housing adjacent to
the grip.
FOOT CONTROLS
Rear Brake
This is a toe pedal on the left-hand side of the machine and it operates the
rear brake only.
Gear Change Pedal
On the right-hand side there are two pedals onc of which projects forwards,
this being the gear change pedal. To engage first gear from the neutral position,
the pedal is moved downwards. To change to a higher gear move the pedal
upwards. To change to a lower gear depress the pedal. The pedal automatically
returns to central position, ready for next gear change.
7
Kickstarter Pedal
This is the other pedal on the right-hand side. Depression of this pedal
rotates the engine.
OTHER CONTROLS
Petrol Tap
This is located under the rear end of the tank. To turn the petrol on, pull
the button out and lock in position by turning anti-clockwise. To turn the
petrol off, turn the button in a clockwise direction and push in.
Lighting Switch
This is operated by a switch on the headlamp, and has three positions—OFF,
LOW, and HEAD respectively. The LOW position is also for use when the
machine is stationary. On direct lighting models the parking bulb draws its
current from a dry battery accommodated in the headlamp behind the reflector.
On battery lighting models turn the lighting switch to “LOW” if the battery is
discharged as this will deliver the maximum charging current to the battery when
the engine is running.
Carburetter Tickler
This is a small plunger in the top of the carburetter float chamber. Pressing
it down pushes down the float and frees the needle valve thus permitting the
carburetter to receive excess petrol.
Steering Lock
Provision is made for locking the steering. Turn the forks to the left, when the
hole in a special frame lug will coincide with a corresponding hole in the bottom
yoke lug. Locking the two lugs together by means of a padlock, prevents the
machine from being driven or wheeled away.
DRIVING
To Start the Engine
Set the gear in neutral (i.e. between the first and second gear positions).
If cold, first depress the carburetter tickler momentarily and close the strangler
(Page 20).
Open the twist grip a small amount, push down the kickstart lever slowly until
resistance is felt, then without releasing the pressure on the pedal, give a firm
downward swing which should set the engine in motion.
During normal running the strangler must always be kept fully open and it
should be opened immediately the engine fires, or should the weather be cold,
at the earliest possible moment. -
Note. While it is necessary to close the strangler when starting from cold,
this may not be necessary when the engine is warm and should certainly not be
so if the engine is restarted after a short wait only.
To Stop the Engine
Make sure that the machine is in neutral gear and close the throttle. If the
engine does not stop it indicates that the throttle is not closing properly. This
can be rectified on Model D1 by adjusting the cable length (Fig. 6), and on
Model D7 by re-setting the throttle stop screw (Fig. 7).
To Engage First Gear
Declutch and move the gear change pedal downwards to its limit. If difficulty
is experienced in engaging first gear when stationary, rock the machine backwards
and forwards maintaining slight pressure on the gear change pedal, until the gear
is felt to engage.
To Move Off
Open the throttle slightly and gently release the clutch lever. As the clutch
engages open the throttle a little further.
To Change Gear (Up)
Disengage the clutch and immediately thereafter raise the gear change pedal
upwards to its limit, at the same time easing the throttle back. Engage the clutch
and re-open the throttle together immediately after changing.
To Change Gear (Down)
Disengage the clutch, open the throttle slightly, and press the gear change
pedal downwards to its limit, all these operations being performed in rapid
succession. Re-engage the clutch immediately.
Note. Violent pressure on the gear change pedal is neither necessary nor
desirable.
To Select Neutral
Neutral is situated between first and second gear. To select neutral from first
gear, depress the clutch lever fully, and lift the gearchange pedal gently until it is
felt to click into the neutral position. If the lever is lifted up too far it will travel
through to second gear. To select neutral from second gear push the lever down
until it is felt to click into position.
Riding Hints
Avoid violent acceleration and braking, particularly on wet roads. Always
use both brakes together and apply them smoothly and progressively. Try to
anticipate the need to change gear or brake so that your riding is not jerky or
untidy. Maintain a natural riding position as this provides maximum control
and prevents discomfort on long journeys.
RUNNING-IN
The rider who has just purchased a new machine for the first time will do
well to remember that all the hidden working parts are just as new as the enamel
and plating which he can see, and that they must not be overloaded until they
are well run-in.
This running-in is really the most important period in the life of the engine,
and the handling you give it during the first 1,000 to 1,500 miles will determine
what sort of service it is going to give you later,
It is advisable not to exceed half throttle in any gear during the first 500 miles.
The mode!'s maximum will then not disappoint you. If you try to put it through
its paces too soon you will run the risk of seizure and other troubles which may
have a lasting effect on the engine, and, in any case, until it is really run-in 1t
will not be at its best.
Avoid sudden and sharp acceleration, especially when the engine is not pulling
under load.
Do not force it up hills in top gear, when a change down would ease the load.
Carry out the periodical maintenance details described later with faithful
regularity.
After the first 250 miles (400 km.), remove the smailer of the two screwed
plugs from the bottom of the crankcase and drain out any oil which may have
accumulated there. With the petroil lubrication system employed there is never
9
+.
a considerable quantity of liquid oil in the crankcase, but whatever oil there is
should be drained away, and this is preferably done while the engine is warm
immediately after a run, as the oil will flow more freely and carry with it any
foreign matter which may have found its way into the crankcase during the
running-in process.
Make certain on replacing the plug that it is made really tight in order to
prevent loss of crankcase compression.
During the running-in period the gearbox should also be drained and flushed
out and this is preferably done at the same time as the crankcase.
Information regarding the correct grades of oil is given in the chart on
page 21.
ROUTINE MAINTENANCE
To keep the machine in good condition and provide trouble-free running,
maintenance must be regularly carried out. The following list of items requiring
regular attention will serve as a guide to the periods between servicing and the
method of carrying out the various adjustments will be found under the appro-
priate headings in the later chapters.
Weekly
Check tyre pressures and remove any embedded stones or pieces of metal.
Oil brake pedal pivot and all exposed joints and cables.
Fortnightly
Examine the battery (when fitted) and top up if necessary. More frequent
examination is advisable in a hot climate.
Every 1,000 miles
Check rear chain adjustment. Check oil level in gearbox and top up if neces-
sary.
D1. Grease clutch operating mechanism, front fork legs, rear suspension
plungers.
Oil brake cam spindles, and saddle nose bolt (where applicable).
Central stand pivots.
D7. Grease swinging arm pivots (2), clutch operating mechanism (remove
cover).
Oil central stand pivots.
Every 2,000 miles
Check tightness of all nuts and bolts. Change oil in gearbox. Oil the speedo-
meter worm drive. Grease brake cams (D7). Grease hubs (D1).
Every 5,000 miles
Check contact breaker adjustment and grease the felt pad.
Cleaning
Obviously regular and thorough cleaning will keep your machine looking
smart and will help to retain both its new appearance and value. But it helps
also to lengthen its life and maintain efficiency if the cleaning process is carried
out correctly.
Take special care to prevent dust and grit from working into such parts as
hubs, carburetter, magneto, brakes and gearbox.
10
To rub dry and caked mud from the frame, tank and mudguards means that
the enamel on these parts will be subjected to an abrasive action which will
quickly destroy the polish. Soak the mud first, and then float it off with copious
supplies of clean water supplied either with a hose or a sponge. If a hose is
used, take care not to direct the stream of water directly on to the hub bearings,
magneto and carburetter.
When all dirt is removed, dry and polish off with a clean duster.
The engine and gearbox are best cleaned with a brush and paraffin, and then
dried off with a clean rag.
ENGINE
Lubrication
Lubrication for the engine is provided by oil dissolved in the petrol to provide
a mixture commonly called “petroil”. The filler cap on top of the petrol tank
will be found to incorporate a tubular extension which projects into the tank.
This serves as a measure for lubricating oil and is used for preparing the correct
mixture of petrol and oil required. The correct proportion of oil to petrol is
given on page 21, and the grades of oil recommended should be used as lighter
grades may prove unsuitable.
For correct running of the engine and also for adequate lubrication, it is
essential that the oil should be completely dissolved in the petrol, and it is,
therefore, preferable to mix the two in a separate container before pouring into
the tank. If this is not possible, however, as for instance, when obtaining petrol
from a wayside pump, the oil should be put into the petrol after filling up with
the latter and the machine should be shaken thoroughly to ensure correct mixing
of the two liquids. If this is not done, there is the risk of undiluted oil reaching
the carburetter and clogging the fuel supply system. As the only lubrication
for the engine is by means of fuel drawn in through the carburetter the machine
must not be coasted downhill for long periods with the throttle shut as the engine
may suffer seizure through lack of lubrication.
Ignition Timing
The ignition timing is accurately set within very close limits and there is no
manual adjustment for the rider as this has been found quite unnecessary in
practice. The contact breaker cam A, (Fig. 2) is keyed on to an extension of the
mainshaft, and its position with reference to the piston position is therefore
constant.
Any variation in timing can only be secured by moving the contact breaker
housing B (Fig. 2) or the rocker arm C. The former can be rotated through a
very small angle by releasing the screws D, not forgetting to retighten them after
the adjustment has been made. It is emphasised that this is a works adjustment
rather than one which the private owner is ever likely to carry out.
In order to obtain correct timing and proper functioning of the contact
breaker, the points must be set when in the fully open position at the correct
gap, and this point should be checked periodically as recommended on page 31.
To do this, turn the engine until the points are fully open and insert a feeler
gauge between them. The correct gap in this position should be -015 in. (-38 mm.)
and if this is found to be wrong release screw E about one turn with a screwdriver
and move the adjusting plate up or down until the correct gap of -015 in. has
been restored, finally retightening screw E.
11
To check the actual timing remove the sparking plug and turn the engine
until the piston is felt to be at top dead centre by means of a suitable rod inserted
through the sparking plug hole, and then turn the engine back until the piston
has descended #5 in. (3-75 mm.) D1 models; + in. (1: 59mm.) D7 model. With
the piston in this position, the contact breaker rocker arm should just be com-
mencing to rise on the contact breaker cam, and the points should have opened
not more than -002 in. (-05 mm.). If they are open more than this the timing
is too far advanced. If they are open less the timing is excessively retarded
although a small variation in either direction is not detrimental to the running
of the engine.
A
RES
ee == ———
ы DA Te
Y
peer
a ori)
Poe ro NS
Fie. 2. Contact breaker
DECARBONISATION
Decarbonising is extremely simple and should be carried out at regular
intervals of about fifteen hundred miles (2,500 km.) if consistent results are to be
expected. The symptoms indicating an excessive deposit of carbon are undue
roughness of the engine and a tendency to pink under load, erratic running
with excessive four and eight stroking, and an appreciable falling off in power.
This latter item is particularly noticeable when the exhaust port becomes fouled
with carbon as it causes an obstruction to the free escape of the exhaust gas, and
interferes with the correct scavenging of the cylinder which is so necessary for
the efficient transfer of combustible mixture from the crankcase.
12
Silencer
The silencer is fitted with a detachable end cap held in position by a single
central nut inside the exhaust opening. This is easily unscrewed and the cap
and internal baffle removed for cleaning. Note when replacing the baffle unit
that the copper sealing ring is in position before fitting the end cap. The two
plain washers and one spring washer must be replaced on the stud before tighten-
ing the central locking nut.
Removal of Cylinder
First turn off the petrol and detach the petrol pipe by means of the hexagon
on top of the float chamber. The plastic petrol pipe is clipped to the petrol tap
union and should not be disturbed. Next remove the carburetter from the
cylinder stub or flange (according to model). The exhaust pipe must also be
disconnected by releasing the union nut at the front of the cylinder barrel by
means of the special “C” spanner included in the tool kit. If this nut should prove
unduly obstinate, a few drops of penetrating oil should be applied to the threaded
portion immediately above the nut and a little time should be allowed for this to
act before attempting to unscrew the nut. Disconnect the high tension lead from
the sparking plug and unscrew the latter.
The cylinder head and barrel are attached to the crankcase by means of four
long studs, and when the four nuts on the top of the cylinder head are removed,
the head can easily be lifted clear. Removal of the cylinder barrel is greatly
facilitated if the two petrol tank front locking bolts are unscrewed so that the
tank can be raised slightly. Take care when removing the barrel to support the
piston as it emerges from the end of the bore in order that it may not be damaged
as it falls clear.
Piston
Place the cylinder head and barrel on one side on a bench and examine the
piston. It should not be necessary to remove this from the connecting rod, but
if it should be desired to do this for any reason, first remove the circlip from one
end of the gudgeon pin using a pair of pointed nose pliers or some suitable
instrument to lever the circlip out. Then holding the piston firmly in the hand,
tap the gudgeon pin out from the other end. If it is too tight to move, it can be
released by warming the piston by means of a rag soaked in hot water and
wrung out. Application of this rag will cause the aluminium alloy of the piston
to expand more than the steel gudgeon pin, thus releasing the latter which can
then be freely pushed or tapped out. On model D7 be careful not to damage
needle rollers comprising the gudgeon pin bearing in the connecting rod.
Scrape off any carbon which has accumulated on the crown of the piston,
taking care not to damage the relatively soft surface of the metal itself, and after
removing all the carbon, polish lightly with fine emery cloth if desired and
finally wipe clean with an oily rag.
Piston Rings
Now examine the piston rings noting that these are located in their grooves
by means of pegs which engage in the piston ring gaps. If in good condition,
the rings will be found to present a uniformly smooth metallic surface over their
entire peripheries, and if they are in this condition and obviously have a certain
amount of “springiness” as evidenced by the fact that their free gap is considerably
greater than the closed gap when in the bore they should not be disturbed. If,
on the other hand, the rings show signs of heat as evidenced by brown or more
13
highly discoloured patches, they should be replaced by new rings, and in this
case particular attention should be paid to the fit of the ends of the rings on
their locating pegs in the piston ring grooves, and they should also be checked
in the bore to ensure that they have an adequate gap. These points will not arise
if genuine B.S.A. spares are fitted as the gaps on these arc already correct when
the rings are sent out, but if for any reason genuine B.S.A. spares are not
obtainable, these points must receive careful attention. First place the ring in
the cylinder bore in a position where it is clear of the ports and, making certain
that it is square by pressing the skirt of the piston against it or a suitable bar of
material of the correct diameter, examine the gap which should be not less than
specified (see Technical Data, page 5). Having satisfied yourself on this point,
place the ring in its groove on the piston and make certain that it is free without
perceptible up and down play. If it is not free and the groove itself is clean,
rub the ring down on a piece of fine emery cloth laid on a dead flat surface,
using a rotary motion of the arm to ensure uniform pressure on the ring. As
soon as ring is found to be free in its groove, wipe it absolutely clean and fit it
into position. The model D7 pistons are slotted at the bottom of the scraper ring
groove and when the ring has been removed check that the slot is clear of carbon.
Check also that there is sufficient clearance between the inner portion of the
gap and the locating peg in the groove. Do this by closing the ring in its groove
by finger pressure until there is no gap, thus shewing that there is clearance at
the peg underneath. If the gap will not close, indicating that the steps are binding
on the peg, ease the steps gently with a dead smooth file. If the piston has been
removed from the connecting rod refit it, first putting a smear of oil on the
gudgeon pin, not forgetting a new circlip to replace the one which was removed.
The piston must be replaced in its original position—i.e., with piston ring gaps
towards the rear on D1 and the front on D7 engines.
Then put a piece of clean rag over the piston and crankcase mouth and turn
your attention to the cylinder barrel and head.
Cylinder Head and Ports
Remove all carbon deposit from the cylinder head, bearing in mind again
that the aluminium is soft and easily damaged if the decarbonising tool is
carelessly applied, and carefully wipe clean to ensure the removal of all loose
particles. Most of the carbon deposit likely to have accumulated in the cylinder
will be in the exhaust port, and this is most important as explained above.
Scrape this out carefully, taking care not to let the tool slip into the bore and
damage the surface of the latter. Examine the transfer and inlet ports for the
presence of carbon, although this is unlikely to be heavy, and finally wipe the
ports and the cylinder bore absolutely clean.
Big-end Bearing
While the cylinder is off it is as well to test the big-end bearing for wear.
This is done by taking hold of the connecting rod stem and pulling it upwards
until the crank is at top dead centre. Then holding it in this position try gently
but firmly to pull and push the connecting rod in the direction of its travel in
order to feel whether there is any play. If the big-end is in a sound condition
there should be no play in this direction, although it may be possible to rock the
rod sideways, i.e. at right angles to the axis of the machine. If vertical play is
perceptible in the big-end and you do not feel qualified to decide whether the
amount in evidence is permissible or not, you should seek expert advice. This
point is not likely to give trouble, however, provided that the machine has been
carefully used and adequately lubricated, for the big-end bearing is of ample
dimensions for the work it has to do. But if for any reason the big-end bearing
14
has deteriorated as the result of neglect or abuse, it should be replaced and
unless you have the necessary experience and facilities for this class of work it
is preferable to have it done by an expert repairer. For the benefit of the
experienced owner who may wish to dismantle his engine-gear unit, a horizontal
section of this is given in Fig. 3, but it is emphasized that no attempt should be
made to carry out work of this nature unless it becomes absolutely necessary.
Re-assembly
Before attempting to replace the cylinder barrel over the piston, smear the
latter generously with engine oil and then place it over the piston, carefully
manipulating the rings into the end of the bore and seeing that they enter freely
without the application of force. As soon as the cylinder barrel is home, replace
the cylinder head and put the washers and nuts on the four holding down bolts.
Tighten the nuts in diagonal order so as to avoid distortion.
Fig. 3. Horizontal section of D1 power unit
Examine the sparking plug and replace if sound, and finally reconnect the
exhaust pipe and the carburetter.
15
Sparking Plug
The sparking plug is of great importance in satisfactory engine performance,
and every care should be taken to fit the correct type when replacements are
necessary. There is little to be gained by experimenting with different plugs as
the make and type fitted by us as official factory equipment is best suited to the
requirements of the motor. This is Champion Type No. L7, as illustrated in
Fig. 4.
Fig. 4. The sparking plug
Remove the sparking plug every 1,000 miles (1,500 km.) or so for inspection.
If the carburation system is in correct adjustment the sparking plug points should
remain clean almost indefinitely. An over-rich mixture from the carburetter will,
however, cause the formation of a sooty deposit on the points and, later, on the
plug end face (as upper view, Fig. 4). If therefore such a deposit is found, clean
it off carefully and check your carburetter. Too high a proportion of oil in the
petroil mixture will also cause plug fouling (see page 9). The continued use of
leaded fuel may also eventually produce a deposit on the plug—this time of a
greyish colour.
Fig. 5. Setting the plug points
16
A light deposit due to any of these causes can easily be cleaned off, but if
it is allowed to accumulate, particularly inside the body, the plug may spark
internally with an adverse effect on engine performance—if, indeed, it does not
stop the engine altogether. The plug should be cleaned and tested at regular
intervals, and it is suggested that this service be performed at your garage on a
special “Air Blast” service unit. If eventually the cleaning process fails to restore
the plug to its original condition of efficiency, it should be replaced by a new one.
When inspecting a plug, also check the gap between the points. This should
be -018--020 in. (-44-- 50 mm.) and adjustment should be made by bending the
side wire (Fig. 5). Never attempt to move the centre electrode, and it is always
advisable to use the special plug gap tool illustrated, obtainable from any
Champion Plug stockist or from the Champion Sparking Plug Co. Ltd.,
Feltham, Middlesex. Feeler gauges are attached to verify correct gap.
When refitting a plug, make sure that the copper washer is not defective in
any way. If it has become worn and flattened, fit a new one to ensure obtaining
a gastight joint.
Screw the plug down by hand as far as possible, then use a spanner for
tightening only. Always use a tubular box spanner to avoid possible fracture of
the insulator, and do not in any circumstances use an adjustable spanner.
Paint splashes, accumulation of grime and dust, etc., on the top half of the
insulator, are often responsible for poor plug performance. The plug should be
wiped frequently with a clean rag.
7
CABLE )
ADJUSTER mi
NJ
AIR Q
CLEANER =
TICKLER |
RN VET
NEEDLE
STRANGLER
Fig 6. The carburetter
Di.
CARBURATION (Di)
So long as the engine continues to run satisfactorily the carburetter is best
left alone, particularly by the inexperienced rider. The setting employed is
suitable for a very wide range of climatic temperature and road conditions, and
it is highly improbable that the rider will need to modify it in any way. If,
however, it is felt that the conditions under which the machine is operated might
permit of a slightly more economical setting this can be provided by the fitting
of a smaller main jet (A, Fig. 6) or by lowering the jet needle B one notch. The
former alteration will supply a slightly weaker mixture throughout the entire
range of throttle opening, whereas an alteration to the jet needle position has
little or no effect on the full throttle setting. Conversely, the fitting of a larger
main jet enriches the mixture throughout the entire range, while raising the jet
needle a notch has a similar effect on intermediate throttle openings only. It is
emphasised, however, that no alteration to the setting should be made except for
special requirements, and only then on expert advice.
CARBURATION (D7)
The carburetter is of simple and robust construction and the only attention
that may be required is adjustment of the pilot jet and throttle stop.
An exploded view of the carburetter is shown in Fig. 6A. Opening the twist
grip throttle control raises the throttle slide thus controlling the supply of air
to the engine. The tapered needle controlling the supply of fuel is attached
to the throttle slide so that a balanced mixture is always provided. The needle
has five notches at its upper end and it is secured in the throttle slide by a spring
clip which locates in one of these notches. The throttle valve size and the needle
position are carefully set before despatch from the factory and no alteration to
these settings is necessary or desirable.
Mixture control at low speeds is controlled by the pilot jet which has an
adjustable air supply. An adjustable throttle stop is also provided to regulate
the slow running speed.
To achieve good petrol economy accurate adjustment of the pilot jet and
throttle stop is important. These are adjusted before the machine leaves the
Works, but the best setting may vary slightly to suit riders requirements or
particular localities. The adjustment should be made with the engine warm.
Screwing in the pilot air screw restricts the air supply thus giving a richer
mixture, and unscrewing it weakens the mixture. The best way to adjust is to
screw in the pilot air screw until the mixture is obviously too rich and the engine
starts to run irregularly, and then unscrew the adjuster until the engine runs
evenly. If it is unscrewed too far the engine may cut-out or may spit back
through the carburetter when the throttle is opened. When the proper adjustment
has been determined, the engine may be running too fast and in this case the
throttle stop should be unscrewed. If considerable alteration to the throttle
stop has been made, the pilot air screw should be re-adjusted. In the case of
blockage, the jets are easily exposed for cleaning by simply removing the covering
caps. The main jet can then be unscrewed with a suitable spanner and the pilot
jet with a screwdriver. No advantage will be gained by altering the jet sizes from
those recommended.
18
Throttie Return
Clip and Notch
Spring и
Adjustment for.
Needle Position
Jet Block
Throtue Naedie — : ‘ Pilot Air Passage
Tichler Assembly
Fig. 6A. The Carburetter. D7
19
ALL MODELS
Special Note. New riders especially are advised to study the action of the
strangier and to treat this device with respect. It should only be used momentarily
when starting from cold and even then only when necessary. Immediately the
engine fires it should be opened. This point is of special importance in the event
of difficult starting, possibly due to some other circumstance such as a defective
sparking plug, for repeated operation of the kick-starter with the strangler closed
results in the accumulation of liquid petrol in the crankcase and when this occurs,
starting is quite impossible until it is drained away by the removal of the crankcase
drain plug, which is the smaller of the two plugs under the crankcase.
Air Cleaner
This is built into the carburetter intake bell and it requires to be dismantled
and cleaned periodically, say, every thousand miles (1,500 km.). To do this,
release the clip bolt, and take the bell off. Soak it thoroughly in petrol, allow it
to dry, and re-assemble.
Carburetter Strangler
This is built into the air intake “bell” of the carburetter, and consists of a
perforated plate which when rotated covers or uncovers similar perforations in
the bell, thus varying the amount of air admitted to the carburetter. When the
strangler is “closed” (i.e. brought into operation) by raising the small lever on
the right-hand side, this closes the perforations, thus reducing the air admitted to
the carburetter to a minimum and providing in consequence a very rich mixture.
The strangler should at all times be kept open except when starting from cold.
TRANSMISSION
Front Chain
The front chain runs on short fixed centres and adjustment for tension is
neither required nor provided.
This chain will run for many thousands of miles before examination is
required. This operation involves the removal of the primary chain cover
(Fig. 7), after the kickstarter and gear change pedals, both of which are mounted
on splines and locked by pinch bolts “B” and “C” respectively, have been removed,
together with the five securing screws “D”. The normal up and down play on
the front chain is up to $ in. (1 cm.) and the maximum permissible, indicating
that the chain is unduly worn and requires replacement, is about 3 in. (2 ст...)
MODEL D1
5 7 6L 10
HL 12 2
KEY LUBRICATION POINTS
(L indicates left hand side, remainder right band side or both sides.)
RECOMMENDED LUBRICANTS
(Summer and Winter).
Mix one of the following Oils with petrol
in the ratio of 1:20 unless otherwise shown.
1:20—two filler cap measures to each gallon of petrol.
1:16—two and a half filler cap measures to each gallon of petrol.
Oil -
Brand Grease Points D7 Front Forks
Engine Gearbox
Castrol Castrol Two-Stroke Castrol XXL Castrolease L.M. Castrolite
Oil (1:
or Castrol XXL
Shell 2T Mixture or Shell X-100 40 Shell Retinax A Shell X100-20
2T Two-Stroke Oil
Esso Esso Two-Stroke (2T) Esso Extra Esso Multi Purpose Esso 20W/30
Motor Oil (1:16) Motor Oil 40/50 Grease H
or Essolube 40
Mobil MobilMix TT (1:16) Mobiloil BB Mobilgrease MP Mobiloil Arctic
or Mobiloil BB
BP BP Zoom or Energol SAE 40 Energrease L2 Energol SAE 20
Energol Two-Stroke Oil
Regent Motor Oil 2T Havoline SAE 40 Marfak HavolineSA F20W
Multi purpose 2
21
MODEL D7
13 L (GREASE) 2 10 | 14
6L
NL 12 9
13 (GREASE)
ENGINE OIL
No. Item Pages
1 Petroil Mixture .. . .. 11
2 Gearbox and Primary Drive .. 10
GREASE
No. Part Pages
3 Wheel Hubs (D1) 10
5 Fork Legs (D1) 10
6 Clutch Operation .. 10
8 Rear Suspension (DI) .. 10
9 Contact Breaker Cam Pad .. .. 10
8 Swinging Arm Pivot (D7) (see p.30) .. 10
13 Brake Cams (D7) .. .. .. 10
A FEW DROPS OF ENGINE OIL
No. Part Pages
10 Saddle Nose Bolt (Except with dual seat) 10
11 Brake Pedal .. .. .. . 10
12 Stand Fulcrum .. —
13 Brake Cams (D1) 10
14 Handlebar Levers . .. —
— Control Joints and exposed cables 10
(not illustrated)
7 Speedometer Drive 10
Primary Chain Lubrication
This has a common oil supply with the gearbox and therefore does not
require separate attention, beyond the instructions for the gearbox.
e ===
A =>
Dw №.
|
Fig. 7. Primary drive
Care of the Rear Chain
It is a good plan periodically to remove the rear chain, clean it thoroughly in
petrol or paraffin, and then gently warm in a mixture of grease and graphite.
When cool wipe off excess grease, clean sprockets and replace chain. Remember
when replacing the chain, which is fitted with a detachable connecting link, that
the spring fastener must always be put on with the closed end facing the forward
direction of travel (i.e. on the top run) of the chain.
Rear Chain Adjustment
Adjustment of the rear chain involves moving the rear wheel and is described
on page 25.
Clutch Control
The clutch adjustment will be found at the left-hand end of the gearbox
mainshaft (sce Fig. 8) and it consists of an adjusting pin C screwed into the
clutch withdrawal quick thread sleeve and a locknut B to secure it in position.
These items are protected by an outer cover on Model D7. The adjusting pin
presses against the clutch withdrawal rod with a steel ball interposed and the
withdrawal mechanism must at all times be so adjusted that there is a slight
amount of play between the pin, the steel ball, and the operating rod, in order to
ensure that the lutch springs may exert their full pressure on the driving and driven
plates. If there is not sufficient play there will be a tendency for the
clutch to slip continually owing to reduced spring pressure, and this in
23
turn will cause over-heating and serious damage to the clutch itself. If the play
becomes excessive, difficulty will be experienced in changing gear, as the clutch
may not fully disengage, in which case the control should be adjusted as explained
Ow.
To adjust, release the locknut and holding it with a spanner turn the adjusting
pin with a screwdriver back one or two turns. Then, still holding the locknut
with a spanner, screw the adjusting pin gently in until it is felt to meet some
resistance. Then unscrew it half-a-turn and holding it in this position retighten
the locknut. If the adjustment is correctly made in this manner, it will be found
that there is a small amount of free play at the clutch lever on the left handlebar
before this is felt to take up the spring pressure during the action of declutching.
Esper тный
Fig. 8. Clutch control adjustment. (Model D1)
The clutch operating mechanism should be greased at regular intervals to
maintain it in good condition (see Page 10).
Clutch Dismantling
Before dismantling the clutch, the primary chain case cover must be removed
as described under Front Chain on page 20. The clutch springs must be com-
pressed by pressing the outer plate inwards until the circlip retaining the spring
24
pressure plate can be removed. Care must be taken to see that the springs are
properly compressed as damage may result if they are released suddenly and the
job is best accomplished with the aid of special clutch spring compressing tool
61-3191. When the spring pressure plate is removed the three plates carrying
friction pads can be withdrawn, together with their mating plain plates. If the
pads are burnt or otherwise damaged, the plates should be replaced. Re-assembly
is carried out in the reverse order.
Gearbox
The gearbox, although built in unit construction with the engine, is self-
contained as regards lubrication. Engine oil is used for lubricating the gears and
primary drive, and the correct level is determined by a dipstick incorporated in
the gearbox filler plug. (4, Fig. 8.)
When topping up the gearbox pour engine oil in until it just reachcs the
bottom of the dipstick attached to the plug when the latter is placed in position,
so that when it is screwed down the oil level will reach the graduation.
To change the oil in the gearbox remove drain plug E (Fig. 7) at bottom of
gearbox and drain out old oil. Wash out gearbox with flushing oil and refill
with new oil through filler hole À, to level of dipstick.
WHEELS
Hub Lubrication (D1)
Inject grease through the nipples in the centres of the hubs. Do not over-
lubricate, or grease may be forced on to the brake linings and cause ineffective
brakes. Two or three strokes of the grease gun should be ample. DO NOT
LUBRICATE WITH OIL.
Hubs (D7)
These are fitted with ball journal bearings, and no adjustment is either provided
or required. The bearings are packed with grease during assembly and this should
last until the machine needs a complete overhaul.
Front Wheel Removal (D1)
The brake cable must be uncoupled at the lever on the brake cover plate and
its adjuster unscrewed from the anchor plate. Take off two spindle nuts. Then
undo the three mudguard stay bolts on the other side (i.e. the nearside) and lift
up the nearside fork leg enabling the wheel to drop out at an angle. This proce-
dure is necessary because of the fork anchor plate on the cover plate. Replace-
ment is carried out in the reverse order.
Front Wheel Removal (D7)
Disconnect the brake cable at the lever on the brake cover plate and then
remove the nut securing the cover plate to the fork leg. Remove the caps at the
bottom of the fork legs, supporting the wheel as this is being done and withdraw
the wheel. When replacing make sure the spindle ends are level with the end
faces of the caps.
Rear Wheel Removal
Disconnect the speedometer cable from the speedometer gearbox and remove
the knurled adjusting nut from the rear brake lever. The rear chain should be
disconnected at its spring link and unwound from the rear wheel sprocket. It
is advisable to leave the chain in position on the gearbox sprocket. On Model D7
it will be necessary to uncouple the cover plate extension at the swinging arm.
25
Finally, slacken the spindle nuts sufficiently to allow the wheel to be withdrawn.
During re-assembly make sure that the slot in the brake plate extension engages
on the locating peg on the fork end on Model DI, and that the cover plate
extension bolt is securely tightened on Model D7 and that the chain adjusters are
up against the ends of the lugs.
Rear Chain
The rear chain is adjusted by means of screw adjusters in the fork ends at
the back of the wheel spindle. First slacken off the knurled rear brake adjusting
nut, as the brake rod may prevent free movement of the wheel. It is not necessary
to disturb the speedometer gearbox unit. Slacken off the spindle nuts A (Fig. 9)
and tighten the adjusting nuts B until the chain tension is correct.
The rear chain should be adjusted with the machine on its stand, i.e., with
the rear wheel in its lowest position in the rear suspension. The adjustment is
correct when the total up and down movement in the centre of the chain run
at its tightest point is $ п. for plunger frame models and % in. for swinging arm
frame models.
Make sure that the wheel is hard up against the adjusters when checking, and
also that the adjustment is equal on both sides of the wheel so that the latter is
In correct alignment in the frame. This can be done either by glancing along the
line of both wheels when the front wheel is set straight, or by means of a long
straight-edge or the edge of a plank placed along the sides of the wheels. The
straight-edge should touch both walls of both tyres.
After adjusting, do not forget to retighten nuts A.
26
Brakes
In the case of the rear brake a knurled nut on the brake rod effects any adjust-
ment necessary, and a few turns are all that is required to improve braking
efficiency. The front brake is adjusted by means of the knurled thumb nut on
the cable stop at the lower end of the forks.
Brake Shoe Removal and Replacement
After the brake plate has been removed from the wheel, the brake cam lever
should be detached and the cam spindle pushed in slightly to allow the shoes to
clear the brake plate. Insert a screwdriver between the brake shoes at the fulcrum
pin and twist the screwdriver.
Place a small lever between one of the shoes and the cover plate and lever
the shoe away from the plate until the spring pressure is released. Both shoes
can then be lifted away from the cover plate.
The shoes can be replaced by the reverse procedure. Hook the springs on
to the shoes and place the ends of the shoes in position on the fulcrum pin and
cam lever. Then push the shoes outwards until the springs pull them into their
correct position.
Note: The brake shoe springs are quite strong and care should be taken that
the fingers are not trapped by the brake shoes during these operations.
Complete re-lined brake shoes are available through the Exchange Replace-
ment Service which operates in the British Isles only.
FRAME AND FORKS
Forks
D1. There is no adjustment for the telescopic forks fitted to this model. The
only maintenance required, apart from the routine check up on the tightness of
nuts and bolts, is regular lubrication of the fork sliding members via the grease
nipples attached to each fork leg as indicated on page 22.
Application of the grease gun to these nipples charges the annular space
between the fixed outer member and the sliding inner member of each fork leg,
and several strokes of the grease gun should be given every 1,000 miles in order
to ensure that the supply of lubricant is maintained.
D7. Under normal conditions the only servicing which the front forks require
is occasional renewal of the oil. The need for this may be indicated by excessive
movement of the forks, but it should only be necessary after considerable mileage.
Prise out the cap on the top of the fork leg by means of the small hole provided
for the purpose, and with the aid of a tubular spanner unscrew the small nut thus
exposed. Then remove the large nut which carried the cap. Disconnect the
mudguard stay, and unscrew the stud which is also the lower mudguard connec-
tion. Allow all the oil to drain out, then apply the front brake and depress the
forks a few times to drive out any oil remaining in the system. Replace the
drain stud and fibre washer.
Add } pint of an S.A.E. 20 oil to each leg (see lubrication chart, page 21)
and replace the top nuts and cap.
Protective Gaiters (D1)
These are fitted to prevent the entry of foreign matter into the moving parts
and are a push fit on the fork tubes. Periodically remove these gaiters, cleaning
and greasing the sliding members.
27
Steering Head Adjustment
It is first necessary to raise the front wheel clear of the ground—this can best
be done by lifting the machine on its stand and putting some small weight on the
saddle or carrier causing the rear wheel to rest on the ground. Test for play by
grasping the fork legs and attempting to push them backwards and forwards.
If play can be detected the head bearing requires adjustment. Slacken the top
clip bolt 4 (Fig. 10). On machines fitted with a bulb horn unscrew this item and
lift off the steering head dust cover. On other machines the dust cover is held in
position by a central screw.
tad
/
FRERE
Vitre
\
e
cr
ViVi yy
' Ta
\ \\
\
Н
À
HE
EEES
tr
PESTE La EE qe
1
\
\ \
\
\
Vinny,
N |
Er
РРР LC
=
ННННННЫНННЫННЕЫ
tania
\
LAL
\ \
\
ЕЕ РР
¥
ss
HEI
y
ha de]
A VAN
NW
\
\
\
ai V4 A N ЗЕ
“O
7
ni
pr
Fig. 10. Model D7. Front Fork and steering head
D1 Model only
Slacken the clip bolt on each fork leg below the lamp so that the bottom yoke
is free to take up a new position. Then release the steering head locknut and
tighten the adjusting nut underneath until any slackness has been taken up. Do
not over-tighten or steering will be stiff and the ball races may be damaged.
Finally retighten the locknut. Tighten all clip bolt and nuts.
Note. Should both nuts be removed for any reason take care to see that the
thicker adjusting nut is replaced first with its recess downwards.
Model D7
Slacken the clip bolt on each fork leg below the lamp so that the bottom yoke
is free to take up a new position.
28
Release the steering head clip bolt A. Fig. 10, and tighten adjuster nut B
until any slackness has been taken up. Do not over-tighten or steering will be
stiff and the ball races may be damaged. Finally, retighten the steering head clip
bolt À, followed by those on the bottom yoke.
Rear Suspension (Model D1)
To dismantle the rear suspension, first detach the rear wheel, and then release
pinch bolts 4 and B.
CF TOES TILE TTITETIITEI FITTS SIE ESTHET IS IT EFT TTTIFTIIFTETITIrIIS SETI TITTIES ath
Ai A A
as
N
"E E > A A
HY ove.
д) ХС
LAs —/
mmm
y ye
A rer
dra dad dela dsd rr fry yr Fr Fy ry rl yyy yry ry
»
AE
he i E
DD 777277? 277777 7777777277777? EIE IF ETF ISITE
|
|
|
Fig. 11. Rear Suspension Unit (D1)
The central columns of the suspension units can then be tapped out from
underneath and withdrawn through the top lugs. When this is done the remainder
of each unit can be slid off sideways from the bottom lug, and laid on the table
for complete dismantling, which consists merely of taking the various pieces
apart, carefully noting their respective positions for subsequent reassembly. The
wheel spindle brackets which, together with the bearing sleeves to which they
are attached, form the spring plungers, can be separated from the sleeves when the
29
pinch bolts C are withdrawn. Note that each of these engages in a notch in its
bearing sleeve and also that the studs at A and B similarly engage in notches in
the central columns. These are essential for correct engagement and locking,
and particular attention must be paid to their proper alignment on reassembly,
Rear Suspension (Model D7)
The two suspension units each comprise a telescopic damper unit and a
totally enclosed coil spring. The hydraulic dampers require no attention whatso-
ever. They are sealed during manufacture and if they suffer damage or become
ineffective they must be replaced.
The complete suspension units can be removed from the frame after detaching
the pivot bolts at the top and the retaining nuts at the bottom.
The swinging arm pivot is provided with grease nipples and should be
thoroughly lubricated every 1,000 miles with Mobilgrease Special.
Frame
The frame will not require any attention unless the machine has been involved
in an accident. It should then be inspected very carefully and the wheel alignment
checked. If the frame is damaged or distorted it must be replaced or returned
to your B.S.A. dealer for rectification if feasible.
THE ELECTRICAL SYSTEM
The ignition and lighting equipment is fed from the ignition generator, con-
sisting of a permanent magnet alternator which, on the basic model, provides
alternating current for direct A.C. lighting.
On the D1 machines fitted with battery lighting, the alternator charges the
battery via a metal plate rectifier and the lights, horn, etc., take their D.C.
supply from the battery. The alternator will keep the battery in a fully charged
condition under all normal load conditions and this is accomplished by a system
of coil switching which adjusts the generator output according to the load.
The design of the coils ensures regulation of the output over the working
speed range.
In the case of the D7 models where a battery is fitted, an A.C./D.C. trickle
charge system is employed. Of the three lighting coils housed in the stator plate,
the two outer coils are connected in series, with one end earthed, to provide A.C.
current for the main headlamp bulb. There is no head light unless the engine is
running. The small centre coil is connected via a small full wave rectifier to the
battery and provides trickle charge current with the lamp switch in all positions.
The trickle charge system provides battery current to operate parking lights,
stop light and D.C. type horn.
Battery
Access to the battery on Model D7 is obtained by removing the two nuts and
washers under the dual seat adjacent to the suspension units, so that the seat can
be lifted and pulled away to the rear.
About once a fortnight take off the battery lid, remove the filler plugs from
each of the cells and examine the level of the electrolyte. If necessary, add
sufficient distilled water to bring the level of the electrolyte up to the top of the
separators. Do not use tap water and do not use a naked light when examining
the conditions of the cells.
The condition of the battery should occasionally be checked by taking
hydrometer readings of the specific gravity of the electrolyte. If distilled water
has been added a reading should not be taken until after the machine has been
30
used, to ensure that the electrolyte is thoroughly mixed. The specific gravity
readings should be as follows:
Temp. Fully Charged Requires Charging
120°F, 1-270 1-220
100°F. 1-280 1-239
80°F. 1.285 1-235
60°F. 1-295 1-245
40°F. 1-305 1-255
20°F, 1-310 1-260
0°F, 1-320 1-270
—20°F. 1-325 1-275
The readings for each of the three cells should be approximately the same.
If one cell gives a reading very different from the others it may be that the
electrolyte has been spilled or has leaked from this particular cell or there may
be a short circuit between the plates. If leakage from the top of the battery is
known to have occurred, due to a spill, the battery should be topped up with
battery acid of suitable specific gravity. a
Never leave the battery in a discharged condition as it will suffer permanent
damage. When standing idle the battery should be given a freshening charge at
least once a month. Twelve hours at one amp. is recommended, Keep the top
of the battery clean and smear the terminals with vaseline to prevent corrosion.
A positive earth wiring system is employed. Make sure that the battery is
connected correctly, 1.e. with the positive or + side of the battery connected to
earth.
unning Without a Battery
к It is never advisable to run without a battery in circuit, for if the lights should be
inadvertently switched on whilst the engine is running, all bulbs will immediately
fuse. Furthermore, there is a very real danger of burning out the rectifier.
If, however, it is imperative that the machine must be ridden without the battery
the rectifier must be completely disconnected at the snap connectors and all leads
properly insulated from each other and from earth.
Generator я
The generator unit consists of two assemblies, namely, the flywheel rotor an
the stator which carries the ignition coil, low tension coils, contact breaker unit
and condenser. The cam is fitted to the extended crankshaft of the engine and is
ated by a keyway.
The Aywhcel houses six laminated magnetic pole faces; it is self-keeping and
may be separated from the stator without any loss of magnetism. a
The set requires very little maintenance and if the following points are observe
the life of the machine should prove trouble-free.
Check, and if necessary, readjust the contacts once every 5,000 miles (see
Page 11). Occasionally clean the contacts by inserting a dry smooth piece o
paper between them and withdrawing whilst the contacts are in the close
position, but take care not to leave any paper between the contact faces. Do not
allow the engine to run with grease or petrol on the contacts or they will start to
burn and blacken. If they do, lightly polish with a piece of smooth emery cloth.
After every 5,000 miles it is necessary to re-lubricate the cam grease pad. This
is done by removing the pad and squeezing and working into it a high melting
point grease. Do not use ordinary grease as this is likely to become fluid under
31
|
f
!
|
t
+
heat and contaminate the contact breaker faces. Do not run with a faulty or
damaged high tension lead, and occasionally clean away mud and dirt from
around the high tension outlet block.
If the unit requires any attention beyond the replacement of contact points or
condenser it is recommended that the complete machine should be sent to an
authorised Wipac station.
Rectifier (Battery Set only)
This is fitted between the toolbox and the battery in a position that ensures
air-cooling when the machine is moving.
It is important not to obstruct the air flow to the rectifier by the fitting of
any additional accessories.
Provided the leads are securely attached to the rectifier no service or adjust-
ment should be required.
On the D7 machines fitted with the A.C./D.C. trickle charge system, the
smaller rectifier is situated on a support bar to the rear of the battery and it is
important that the unit is making good contact with its support as this type of
rectifier is cooled by surface contact.
Contact Breaker and Stator Unit
To remove this, first take off the contact breaker cover plate which is held
in position by two screws. Remove the central screw holding the cam A, Fig. 2,
pull the cam out, and then lift out the cam key. Remove the three screws D
holding the contact breaker housing. The whole unit can then be lifted off with
the housing.
Removal of Generator
This should not be attempted by the private owner unless B.S.A. Service Tool
number 61-3188 flywheel extractor is used as described below, otherwise serious
damage to the mainshaft is almost inevitable.
Before proceeding to extract the flywheel from the mainshaft, make sure that
the cam key has been removed from its keyway. Then remove the central nut
and its shakeproof washer. Screw the B.S.A. extractor on to the exposed thread
as far as it will go. Finally, turn the central extractor bolt with a suitable spanner
until the flywheel is drawn from its taper.
Electric Horn
If necessary the horn may be adjusted, as follows:
Remove the rubber plug in the horn body; this will expose the adjusting screw.
À slight turn to left or right while depressing the horn button will enable the
best note to be obtained. Finally replace the rubber plug.
If the horn still gives trouble it should be removed and returned to the
manufacturers.
Headiamp
The lamp front, together with the reflector and bulb assembly, is secured to
the main lamp casing by means of a slotted screw above or below the lamp
according to model. To replace a bulb (or battery on direct lighting models),
therefore, it is only necessary to loosen the screw until the rim can be removed.
To replace the double filament bulb, press the bulb retainer inwards and turn
slightly anti-clockwise, when it can be lifted off and the bulb withdrawn. A
replacement bulb automatically provides correct relationship of the filaments.
32
The best way of checking the setting of the lamp is to stand the motor cycle in
front of a light coloured wall at a distance of about 25 feet. If necessary, slacken
the bolts securing the headlamp on Model D1 or, on Model D7, the two screws
on the nacelle rim, and move the lamp until, with the main driving light switched
on, the beam is projected straight ahead and parallel with the ground. With the
lamp in this position, the height of the beam centre on the wall should be the
same as the height of the centre of the headlamp from the ground.
Parking Battery
The headlamp used with A.C. direct lighting equipment includes a dry battery
(Twin Cell, No. 800) for parking lights and is positioned upside down in the hold-
ing bracket.
Rear Lamp |
A single bulb is used with direct lighting sets plus two screw-in stop light bulbs
with battery sets.
The transparent red plastic portion of the lamp can be removed by unscrewing
the two countersunk screws.
Stop Light Switch (battery set only)
This is operated by the brake rod through a spring. It is desirable to see that
any mud or grease is periodically cleared away from the switch, and the operating
mechanism should be oiled occasionally with thin oil.
GENERAL NOTES
The wiring is connected by means of snap connectors at various convenient
places on the machine and it is desirable occasionally to check it over and make
certain that these connectors are tight.
BULB TYPES
Headlamp (main bulb) 6 volt, 24/24 watt pre-focus,
Headlamp (pilot bulb) D* 2-5 volt, -25 amp. M.E.S.
Headlamp (pilot bulb) 6 volt, 3 watt. M.E.S.
Rear lamp bulb D* 6 volt, 3 watt.
Rear and Stop lamp incorporating three bulbs
Rear lamp bulb 6 volt, 3 watt.
Two Stop light bulbs 6 volt, 6 watt.
* D indicates direct lighting set
33
HILIN$ dOLS
gw AY id 4 2015
BS DFMIRIS - ROT LIND)
HAC ]
"
Y “lí
1
m
| :
= E
Ole alí
> IT ‘| Sid “BOS 5 cg
up | +
= I Е
"FER 3
oor ops! m - —
* |5 © 1
0 ! = ba E
I i z f= -
! >| влом VÁ >
: Si MOLIENNCO И 4 À -
| — PU A Pe NS EL
i FF MOB |, \ NO ; т >= 14 и CERES
-
Г ВЕ | | / NACH
| i AA Aas O
LWA GR HL
en Tim a ТО
—— p—— NRO Ee > .
A | TST rn HIJIMS | с
т Cas Have © STI я
неее um TT MATI X
LF "TE ve Lo) >
A + ©
MAMAS L Ye
E
-
1
o
MET AS
dw HALINOOIIdT
HWOIVEINAD _ NOL LIND
не
!
]
—
19 e"
aa HME
L—
<<
(D1 only)
ELL ZF EC
\ AA
Fig. 14. Wiring Diagram Battery Lighting
HOLIMS SiC
33
gy
ip
2 Ma waves So
> )
x > || *
æ IX
EN 5
| So
| | o
А
| эл LH \
| | Z YE. ASE =
Lt ) RES Eo dmv 1070 ' 3
. 150m +O ` \ Ay
PY vds $ dOLS AWE on CU — ı ; &
ere srg va pq
NO HIEYVA ELLE | re — "a
- ——————— — f - € i i
ча м | I Ly — = 7 ] Awash Leva I 10 | - A а Q
A Lr ооо Nova зас) 1. MEL SAT CA
ns т | ; С И d#vIGYE"
22%, Mm I TESTOR e e ATW LAMA o
Ра . 15! E Во :
”> e L wo L_ e | 4 У < | $ 5) Г 1 j 5
sam mT TTT TT NN Cg TTT Te = SHO LEMME? a a - IG — E | i ' =
MEA Smet = ! 7 ; TE es X / pa
S5H0L3ZWN03 u © ae —_— — NX A | | / =
* EPI ALALELELI PILLAN ALA CCAA VELAALA a aaa oa P 1 ! |
Ce LL LEMA TITUS ¢- | |
1 1 IT => ППП лее ет TUS BRO TUU е
HE —— o Tm oia AY TT .
; i | т уе т ———— | fo Jo en
| го | a 1} > —
op N 7 17,
ho ® | II >
DEE > EBs
Це > > , o Ti Be
А ; TTT Ry
eo! !
Fa x |
pom .
ET |
Eta
LE A
po | 78
Elo |
NES — ;
ad TT =1-1-
+ MH CAR
/ WY 1 коазммоОза
(* è > LIWDORRS dn
À j É HDIIMS aid
HDLIMS dOLG =
a —--
К —
34
|
i
I
I
DUCHA
SWITCH
HON
®
Gv dw REAR
TWIN Ev Ev 5108
STOP ¢ REAR LAME
)
о
21
— +4 NT
STOP SWITCH
SWL
Baik
AY
——— =
BLACK
RECTIFIER
MAO
REC
BRON
гл
ны с
;
г
|
|
LTE
Gv.
—
SPARE. PLUG
4,
a 7
<A «<
Г
iI
FRAME EARTH
VIOLET
BLACK
ET Sa a
TRANS
DARK RED
SPEEDOMETER LAMP
Do
SWITCH 6 1
HORN
PUSH
[=
ur
¥
3
В
4
ê
|
= 7 to ha Y | ;
ны Me i
. у
. a
LA
LA Y Bye ин
TRE Py
PILOT be,
Lo He
Эм
~~
1 MEA CL AM
| Gv 24724 w
1
!
\
|
|
Fig. 15. Wiring Diagram Battery Lighting
(D7 only)
36
SERIES 55. IGNITION - GENERATOR.
AC LIGHTING.
D.C, TRICKLE CHARGE
TO BATTERY FOR PARKING,
B.S.A. MOTOR CYCLE SPARES STOCKISTS
Save time and postage by contacting your nearest B.S.A. Stockist Гог В.5.А,
Spare Parts, Spare Parts Catalogues, Instruction Books, Transfers, etc.
All B.S.A. Dealers carry stocks of B.S.A. Spare Parts but the following
appointed Stockists maintain a comprehensive range.
Town
Aberdeen
Aberystwyth
Accrington
Aldershot
Alloa
Andover
Ashington
Aylesbury
Banbury
Barnsley
Barnstaple
Bath
Bedford
Belfast
Biggleswade ...
Birkenhead ...
Birmingham
Blackburn
Blackpool
Blandford
Bolton...
Boscombe,
Bournemouth
Bradford
Bridgwater
Basingstoke ...
Banbury
Name of Stockist
‚ }. Dawson
Gwalia Motor Co.
.. Bill Snape Ltd.
.. Phillips Bros. (Aldershot) Birchett Road
td.
.. J. G. Robertson...
.. Corbett & Ellis {Andover)Weyhill Road
Ltd,
... Mains of Ashington
. Claude Rye
. Trinder Bros.
. T. Garner & Son
Bob Ray Ltd.
. R. U. Holoway & Son . ..
Bryants ..
Bob Simister Ltd.
Address
. 24-26 Thistle Street ...
. George Cheyne (Cycles) 147/149 Holburn St.
td.
. North Parade ..
. 379 Blackburn Road
. 55-57 High Street
.. Laburnum Terrace
. 44 Walton Street
. 2 &3 Broad Street
. Sheffield Road
. 43 High Street
. 32-33-34 St. John's Road
Bathwick.
. The Imperial Cycle Co. 58 St Loyes
. W. J. Chambers & Co.
106 and 108,
Donegall Pass
. 25, 27, 72 and 74,
Shortmead Street
. 540 New Chester Rd., Rock Ferry
1452
Rock Ferry.
County Cycle & Motor 266 Broad Street
d 4 Bath Row (Repairs)
(closed Saturday | p.m.)
Co. Ltd.
. Shovelbottom's Ltd.
. Aston Auto Motors
. 5. & G. Motor Cycles
(Blackburn) Ltd.
... J. Hall & Son
. The Badger Garages Ltd.
. Charlie Robinson
... Craze Bros.
. C. Sidney Ltd.
J. K. Hurst .
Anderson & Wall
F. Slade ...
. Taylor-Dow
. 172 Aston Road 6
Edgbaston 17
. 376 Ladypool Road,
Sparkbrook 12
Telephone
No.
25556
50341/2
525
4724
14/2
193
2991
3204
3150
2546
2866
4266
Telegraphic
Address
Mocobike,
Aberdeen.
Phillips, Cycles,
Aldershot.
Eborn's.
5084/64101
2374
27253/4 Fastmote, Belfast,
3108
Mid. 2671
Mid, 2817
. C. E., Cope & Sons Ltd. 481-487 Hagley Road, Bearwood
2246/7
South
2212
201/2
15-17 Great Bolton St, 6678
. 102-6 Devonshire Rd.,
{opp. School)
Salisbury Road
. 119 and 121 Higher
Bridge Street
. 473 and 475 Christ-
church Road
. 107 Manningham Lane
... 41 Wakefield Road ...
. 18 St. Mary Street
. May Place, London St.
. Southam Road, Oxon.
37
22130
615
3931
Boscombe
33231/2
29889
22543
2416
1338
2641
. Aston Cross
Anderson & Wail,
Bridgwater
1
1
;
|
!
I
B.S.A. Motor Cycle Spares Stockists—continued
Town
Brighton ..
Bristol
Bromsgrove ..
Bury St
Edmunds
Cambridge
Canterbury ...
Cardiff
ЕТ
Carlisle
Carmathen ...
Castleford
Chapel-en-le
Frith,
Chatham
Chelmsford ...
Cheltenham ...
Chester
Chichester
Clydebank
Colchester
Colne, Lancs.
Coventry
Crewe
Croydon
Crawley
Dagenham,
Essex.
Dalton-in-
Furness
Darlington
Dartford
Derby...
Doncaster ...
Douglas, 1.0.M.Gilbert Harding
Dudley
Dundee
Dunstable
Chesterfield ...
Derby ...
. Coventry Motor Mart ... 86 London Road
td,
. Godfreys Ltd.
. Lewis Thirkell ...
Telephone Teiegraphic
Name of Stockist Address No. Address
. Redhill Motors (Brighton)104 North Road ... 528i
td.
. S.J. Fair Motors Ltd, ... 201-3 Cheltenham Rd. 4-6238/4-1015
Ralphs ... cs ... 110 Birmingham Road 3228
Barclay Motors … ... Kings Road Corner 2345/9
… King & Harper Ltd. ... Milton Road Corner... 3201 Moters, Cambridge
Hallets of Canterbury ... St. Dunstan's Street... 2275/6
... Car Distributors (Car- 134-140 City Road ... 30022
diff) Led.
… Robert Beven & Son ... 29-35 Castle Street ... 27477/8
. W.T. Tiffen & Son ... irishgate Brow... ... 25024 Tiffin, Irishgate,
Carlisle.
Eddie Stephens (Motors) 22-23 Water Street ... 6233
‚ Barrett's Motor Cycles 27-35 Aire Street ... 2983
(Castleford) Ltd,
E. W. Bowers . 129 Town End ... 144
. Grays of Chatham Ltd.. 11-19 High Street ... 4005
Hadlers Garage Ltd. ... New Street ... ... 4844/5 Hadler, Chelmsford
H & L Motors Ltd. ... Bath Street ... ... 12887
. Davies Bros. ... 34 Bridge Street ... 2550
. We Loodridee & Co. East Street ... ... 2033
td.
. John A. Weddell ... 72-114 Dumbarton Rd, 1429
. G.B.R. Motors Led. ... 1-2 East Hill... ... 6131/2
cH Scholfield (Motors) Market Place … ... 859
22146/7 Coventry Motor
art.
. Cokes Garages (Crewe 10-20 Nantwich Road 2011 Cookes Motors,
td.
rewe,
... 228-234 London Road Gy don Gofrabike, Croydon
641/
... 60-62 The Boulevard... 25507
Reginald Smith … ... Imperial House, New Rainham
Road 3284/2766
H. Hume ... … 24/26 Uiverston Rd. … 25
. The Duplex Motor and 10-16 Grange Road ... 207) Duplex,
Cycle Co. Ltd. Darlington.
. White Bros. ... 201/205-9 Northgate... 67757
Schweizo Bros. ... . 177 Lowfield Street ... 4279
. Ingle’s Provincial Garages Wallbrook Road ... 45289
td.
W. Cusworth (Doncas- 7 Hall Gate and 5 4594
ter) Ltd. Market Street ...
... 18 Duke Street ... Douglas
170
. Chas. E, Cope & Sons {93 High Street ... 3464/5/6
Ltd,
... George Mclean Ltd. ... Ward Rd., Riverside 5087 Vehicles, Dundee
Drive
. B. G. England (Dun- Halfmoon Hill, London 843/4
Road
stable) Ltd,
Walter Wragg ... . 95 Lordsmith Street, 3622
Derby
. D. Tye ... ... ... Water Lane, Cromford Wirksworth
2149
38
B.S.A. Motor Cycle Spares Stockists—continued
Town Name of Stockist Address
Eastbourne Jempsons Ltd... … 118 Seaside
Edinburgh ... J. R. Alexander & Co. ¡0-14 Lothian Road
Ltd.
Elgin Farquharsons ... 55-57 High Street
(Morayshire)
Enfield … D.J. Shepherd & Co. 434-6 Hertford Road,
(Enfield) Ltd. Enfield Highway.
Exeter . P. Pike & Co. Ltd. ... Alphington Street
Frome . J. Difazio ... ... 25 Catherine Street
Gateshead, 8
Glasgow, C3 ...
os ca...
Gloucester
Grimsby
Guernsey
Guildford ...
Harrogate
Harrow
Hatfield
Hereford
Holbeach
Lincs.
Hornchurch ...
Hounslow,
Middlesex
Huddersfield
Hull
Huntingdon ...
Hford ...
Hkeston
Derbyshire
Ipswich
Jersey...
Kendal
Kings Lynn
Kirkcaldy
Lancaster
Lancs. ...
Launceston
Leeds ...
Leicester
... Tom O'Loughlin
... Peter Guest Ltd.
O. Carmichae! % Son ... 75, 83 and 87 High
Street West
Bell Bros, (H.P.) Ltd. ... 215-233 St. George Rd,
J. R. Alexander £ Co, 264-280 Great Wes-
Led. tern Road
... Harpers of Gloucester ... 23a Worcester St.
... H. J. Gresswell & Sons 13-15 Osborne Street
Ltd.
. Millard & Co. Ltd. ... Victoria Road
Е. Pascall (Guildford) 11-12 Woodbridge Rd.
Ltd.
... H. Aclam (Prop. H. Baynes)! | Bower Road
... Pinks of Harrow
... Station Road ...
. W. Waters & Sons Ltd. 32 Gt. North Rd.
. A, Kear & Co. ... ... 520 Commercial St.
G. Woodman Ltd. ... 34 Fleet Street
T. W. Kirby Ltd. ... 10 Roneo Corner
Stanley's Motors ... 46-8 Lampton Road
Earnshaw ... ... Manchester Road
... Browns (Witham) Ltd.... 47-49 Witham
Jordans of Hull! ... ... Story Street …
Haliens ... vee ... 10-20 German St.
. 3. 3, Doubl … 14 Mildmay Parade,
? 4. Double Cranbrook Road
Ray Gamble ... Station Road ...
. Revetts Ltd. ... Clarkson Street
, Colebrooks .. ... 224 New St. John's Rd.
(J. O. Poingestre) St. Helier
... 66 Stricklandgate
... 123/85 Wooton Rd.
... County Motors (Kirk- Junction Road
caldy) Ltd.
... Pye Motors Ltd, . Parliament Street
… À. Taylor ... ... 192 Manchester Street,
dham
J. Wooldridge & Son ... Western Road
... Watson-Cairns 4 Co, ... 157/8 Lower Briggate
Ltd.
... Е. W. Campion & Son Welford Place
Ltd.
39
Telephone Telegraphic
No. Address
756 Jempsons,
Eastbourne,
4455 Motorcycles,
Edinburgh.
7188 Elgin 7188
Howard
1631
58241 Piko Exeter.
2913
71815
Douglas Douglas 6414
6414 Glasgow
Douglas Alex Moto,
3802/3/4 Glasgow.
23187 Gloucester 23187
2202
777 Millard Motors,
Guernsey.
Guildford
2274/5/6
5125
0044/5 Pink, Harrow.
“Spares 3328
2255
2239 Kear, Hereford.
3221
8785
Hounslow
1949
1232
.. 29802/33990
16131 Gumption, Hull.
1051-2
3621
Valentine
873
53726/7
Central Colebrooks,
642 Jersey
315
Dysart
5631
3553
Main
4456
21 Wooldridge,
Launceston.
33024/5 Watson-Cairns,
Briggate, Leeds.
58054
B.S.A. Motor Cycle Spares Stockists—continued
Town Name of Stockist Address
Lincoln ... Wests (Lincoln) Ltd. ... 116 High Street
Liverpool, 3 ...
Llawhaden . James Bowen & Sons Llawhaden, near Nar-
berth, Pem,
1 220 5a Barking Road, East
” E.6 ... Glanfield Layrrence (High- 28-32 | Highbury
bury) Lt … Corner ...
London, E6 … Godfrey's Led, ...
> E.7 ... Godfrey's. а. ... . 418 Romford Road, Grangewood Gofrabike,
Forest Gate 1234-5 Forgate.
” E.8 ... Eleanor Motors . 265/7/9 Mare Street Amherst
Hackney 5134-3923
” E.18 Longstaff . 88 High Rd., Wood- Bue,
ford 6367 &
6757
» N.12 George Grose Ltd. . 834 High Rd., Finchley Hillside
2149
» N.12 Glanfieid Lawrence Led. Junction Great Norch Finchley Glanfin, Norphone
Road and North 009} London.
Circular Road
a N.15 Godfreys Ltd. ‚ 94 -96 High Road, Sth. Sta, Gofrabike,
Tottenham. 9960 London,
» N.W.}! J. Grose Led. . 379-38] Euston Road Euston
5231
ns N.W.10 Slocombes Ltd. ... . 269 Neasden Lane, Gladstone
Neasden. 3355
.” S.E.Il Writers Ltd, - 51-6! Kennington Ln. Reliance
1362
„о S.E. 13 F. Parks & Son Ltd. ... 404 Lewisham High St. Lea Green
0535
” S.E.IS West End Motors Led.... 171 High St., Peckham Neweross
258
» S.E.I8 Cleare & Co. Ltd. . | & 125 High Street Woolwich
0174
" S.W.6 Claude Rye Ltd. ... 897-921 Fulham Road, Renown Ryebikes, Walgreen,
Fulham, 617 London,
„ S.W.9 Pride € Clarke Led. . Stockwell Road Brixton
„ S.W.11 Owen Bros. . 19 Battersea Rise, Battersea
Clapham Junction 7816/7
ve S.W.17 Elite Motors . 951-96] Garratt Lane, Balham
Tooting Broadway, 1200
” W.I Godfreys Ltd, . 208-210 Great Portland Euston Gofrabike, London
Street, 2/4
" W.3 Whitby's of Acton Ltd. 273 The Vale, Acton Sh. Bush
5355/6
. W.5 Kays of Ealing Led. . 8-10 Bond Street Ealing Sparesokay, Ealux,
2387 London.
„ W.12 Turners Stores . 81-83 Goldhawk Road, Sh. Bush
Shepherds Bush 2436
Lowestoft . R. Wright « 67-69 London Rd., Sth 645
Macclesfield ... A. Watling - 49 Buxton Road 3592
Maidstone . Redhill Motors (Maid- The Broadway... 3096
stone) Ltd.
Manchester, 3 Tom, Davies (Motors) 2 3 Deansgate
„ ... Fred Fearnley Ltd.
... Alex Parker
. 692-4 Ashton Old Rd.
orthenden
... 128 Chesterfield Rd.
Middlesbrough J. T. Dickinson (Middles- 150-162 Lindthorpe
brough) Led, Road.
Neath ... Fred Rist ...
Mansfield . Henstocks
... 16 Windsor Road
40
Cundles (Liverpool) Ltd. 41 and 6i Byrom St....
Telephone Telegraphic
No, Address
21262
Central Cundles, Central
4148 4148,
Llawhaden
6
Grangewood Gofrabike,
8088 Forgate,
North
2791
... Blackfriars
0681
East Fernbike,
. 31/33 Palatine Road Wythenshaw
[445/6 Manchester,
2062
329 Henstock 329
Mansfield.
3861 Payacob
Middlesbrough.
Neath
780
B.S.A. Motor Cycle Spares Stockists—continued
Town
Name of Stockist Address
Newcastle-on- Dene (Newcastle) Motor Haymarket
Co. Ltd.
Tyne
Newton Abbot J. E, Green & Co.
. 87 Queen Street
Newport, R. J. Ware & Sons ... 69 Commercial St.
Mon.
Northampton G. Lawrence 10-4 Welling Borough
oa
Norwich . Chapmans (Norwich) 38-42 Duke Street
Ltd.
Nottingham E. W. Campion 4 Son Arkwright Street and
Ltd Queen's Road
Oldbury . Bromford Garage . Bromford
Oldham ... Alan Taylor (Northern) 192 Manchester St.
Ltd.
Oswestry ... Roy Evans ... Willow Street
Oxford . H. F. Temple .. 69 High Street, St.
Thomas
” ... John Avery ... 228/230 Banbury Road
os ... Faulkener & Son . 12 Cardigan Street ...
Parkstone ... Bob Foster . 472-5 Ashley Road
Perth ... . M. Shaw & Sons . 143 High Street
Peterborough Burrows Bros. .. ... 55-57 Westgate
Piymouth . P. Pike & Co. Ltd . Millbay Road ...
Pontardulais,
Glam,
Portsmouth
”
Preston
Pulborough ...
. Will Lord .
. Phillips & Bloomfield 10-24 South Street
Radcliffe
Reading
Redhill
Ripon ...
Rotherham
Salisbury
Scarborough
Sevenoaks
Sheffield, |
Shrewsbury ...
Sittingbourne
Slough...
Southampton
Southport
Southsea
St. Helens,
nes,
... Glanfield Lawrence
. Loxham’s Garages Ltd. Central Garage
. Angus Motor Cycles
. Walter Wragg Ltd.
. Sid Moram
. H. F, Brockbank
... Percy Kiln
.. Geoff Duke Ltd.
T. Griffiths ... . Forest Garage
277-281 Copnor Rd.
... 147-157 Fratton Rd.
Jenkins & Purser Ltd.
harniey Street,
Fishergate,
. Bury Gate
. 115 Blackburn Street
Gray & Rowsell...
Motors Ltd.
. Stocker & Shepherd Ltd. 131 Oxford Road and
Weylend Street
... Fortesque ... . West St,
. The Redhill Motor and 50/54 Brighton Road.
Cycle Works Ltd.
. T. Ellis... ... ... 3 High Skellgate,
orks.
Ernest Cross . 55-59 Drummond Se
. Pankhurst (Weymouth) 78 Exeter Street
Led.
E. Andrew . Roscoe Street
. Station Parade
. Stanley Works,
Wellington Street.
. Coleham Head
. 9 West Street
J. R. Meredith ...
Scoones, Garage
... Wexham Corner,
High Street.
.. 152 Portswood Road
. 62 King Street
. 65-67 Elmgrove
Alec Bennett Led,
41
Telephone
No.
. Greenfield Rd, Garage
Telegraphic
Address
2-9165/6 Ened, Newcastle-on-
Tyne,
653
66206
1272
24727
83444
Bro
2225
Main
4456
1144/5
2485
57362/3
57279
3500
483
2154
Piymouth Piko, Plymouth.
63018
... Pontardufais
323
2339
74331
Sales Dept. Loxham's, Preston.
4242
Service Dept.
4243
Bury 4
2002
2635
2212-3983
54143
327
1079
Rotherham
3987
Salisbury
5222/3
. Scarborough
1857
3338
26098 26098 Sheffield
6529
66 Scoones, Sitting.
bourne.
Slough
23767
54081/2/3
5054
P'mouth 23734
3918
B.S.A. Motor Cycle Spares Stockists—continued
Town
Stockport
Stockton-on-
Tees
Stoke-on-
Trent
Stourbridge
Sunderland
Taunton
Thames Ditton
Torguay
Troon,
Ayrshire
Truro,
Cornwall
Tunbridge
Wells,
Twickenham...
Uxbridge
Wakefield
Walsall
Warrington
Watford
Wellington
W estcliff-on-
Sea.
Weston-super-
Mare
Weybridge
Weymouth …
Whitehaven,
Cumberland
Wolverhamp-
ton
Worcester
Worksop
Yeovil
York ...
Name of Stockist Address
. Theobald & Coppack ... 6 Chestergate
T. Cowie Ltd. ... ... 49-50 Brunswick St.
J. & N. Bassett ... Howards Place,
Shelton.
Pearson's Cycle Depot... 31 Market Street
Dunns Garage (Sunder- Wheatsheaf Corner,
land) Led. North Bridge St.
.. T. Cowie ... ... 49/50 Brunswick Se.,
Stockton-on-Tees
. Cowies .,, ... ... | Matamba Terrace,
St. Maries
Glanfield Lawrence ... 13-14 Fisher St.
. We E Edwards (Motors) Station Road ...
td.
- C. $. Russell (York) Ltd. Lawrence Street
42
Telephone Telegraphic
No, Address
2843 Theobald Coppack,
Stockport,
67534
2890
5677
57666
2943 Edwards, Motor
Cycles, Taunton
Comerfords Led. -.. Oxford House, ... Emberbrook
Portsmouth Road 5531
... P. H. Sharam Ltd. ... 244-6 Union Street ... 484 &
7255
Cooper Bros. ... ... 125-129 Templehiil . 925
W. H. Collins ... ... Kenwyn Mews Truro
2168
G. E. Tunbridge Ltd. ... 21 London Road 416 Motors,
Tunbridge Welis.
C. A. Blay ... ... 192-9 Heath Road ... Popesgrove
2103 8: 1435
… J. H. Miles Led, ... 60 High Street Uxbridge
6000
. Parkinsons (Wakefield) 38-40 Ings Road 2087
t *
.. The Motor Cycle Mart 12 Ablewell Street ... 3363
(Walsall) Ltd,
Jack Frodsham Ltd. ... 37a Winwick Street ... 34713
. Lloyd Cooper & Co. ... 6! Queen's Road 2125 Lloyd Cocper
Watford.
... Bill Doran and Matt. Park St. Garage,
Wright Shrops.
J. Costin & Sons ... 233-5-7 London Rd, ... Southend
42215
Wyvern's of Weston 3 Locking Road 524 Wyvern's, Weston-
Ltd. super-Mare
... W.L. Lewis & Sons ... 51 Church Street 2210
Tilleys ... ... ... 9 Frederick Place 72
Mark Taylor ... ... 21 King's Street 252
C. E, Cope 4 Sons Ltd. 168-9 Stafford St. 24605/6
. W. J). Bladder & Son ... 52 Sidbury 2438 Bladder, Sidbury,
Worcester.
. Ezra Sugden Led. .. 109 Gateford Road . 3053
.. The Yeovil Motor Mart Hendford 267
23793 Russell, Lawrence
Street, York.
PROPRIETARY INSTRUMENTS FITTINGS & ACCESSORIES
No expense 15 spared to secure as standard equipment the
most suitable and highest quality instruments and accessories.
Nevertheless, the Company’s guarantee does not cover such
parts, and in the event of trouble being experienced the parts
in question should be returned to and claims made direct on the
actual manufacturers, who will deal with them on the terms
of their respective guarantee, as follows:
Carburetters: В
Messrs. Amal Ltd., Holdford Road, Witton, Birmingham 6.
Dual Seats: В
Messrs. Motoplas Co. Ltd., Waverley Works, Birmingham 10.
Electrical Equipment: |
Messrs. Wico-Pacy Sales Corporation Ltd., Buckingham,
Bucks.
Batteries: В
Messrs. Joseph Lucas Ltd., Birmingham.
Spring Seat Saddles: |
Messrs. Wrights Saddle Co. Ltd., Dale Road, Selly Oak,
Birmingham.
Speedometers: |
Messrs. Smiths Motor Accessories Ltd., Cricklewood,
London, N.W.2.
Tyres: В
Messrs. Dunlop Rubber Co. Ltd., Fort Dunlop, Birmingham.
SPECIAL NOTE
Claims under guarantee to B.S.A. Motor Cycles Ltd., should be
submitted through the B.S.A. dealer from whom the machine
was purchased.
43
">
/
Stiahnuť
Len priateľské pripomenutie. Dokument si môžete pozrieť priamo tu. Ale čo je najdôležitejšie, naša AI si ho už prečítala. Dokáže vysvetliť zložité veci jednoducho, odpovedať na vaše otázky v akomkoľvek jazyku a pomôže vám rýchlo prechádzať aj tie najdlhšie alebo najkomplikovanejšie dokumenty.
Reklama