Installation   Instructions  

NGW ‐ 230    

Wireless   Gateway  

 

UIS

 

Contents

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1.

Product Features

2.

Package Contents

3.

Components and Description

4.

Install this product

1.

Product Features

 External wired ADSL Internet

 Internally wired / wireless LAN Wifi network control functions and Sensors

2.

Package Contents

Wireless Gateway Host-----x1

Power Supply--------------x1

Instructions--------------x1

3.

Components and Description

Front

#   Item

1 Function indicator

2 Setting key

Back

4  

1,2  

Directions

Connection and function indication。

Setting pairing

3

2  

1  

#   Item

1 Power supply

Directions

Connect the dedicated AC power supply of the slot

slot

2 LAN slot Connected to a computer or HUB, identify mechanisms to support 100Mbps / 10Mbps automatic switching。

3 WAN slot ADSL modem connection or existing network。

4 USB slot USB 2.0 slot

4.Install this product

 

1 Select Install the appropriate location such as the installation guidelines 。

2 Plug in the power transformer, either insert the wireless host side into the wall 。

3 After plugging in the power function indicator flashes red, wait about 40 seconds that is the boot to complete

。

4 The basic setting of this product

Open your web browser 。

Enter in the URL http://192.168.19.254

Press Enter 。

Enter the network password dialog box appears, enter "123" in the Password field inside, click on "LOGIN"

That will open the product's basic settings screen. Detailed instructions, please refer to the System Installation Manual 。

5 Press the key to the front of the set and each sensor pair 。

 

This   device   complies   with   Part   15   of   the   FCC   Rules.

  Operation   is   subject   to   the   following   two   conditions:   (1)   this   device   may   not   cause   harmful   interference,   and   (2)   this   device   must   accept   any   interference   received,   including   interference   that   may   cause   undesired   operation.

 

 

Notice   :   The   changes   or   modifications   not   expressly   approved   by   the   party   responsible   for   compliance   could   void   the   user’s   authority   to   operate   the   equipment.

 

   

IMPORTANT   NOTE :   To   comply   with   the   FCC   RF   exposure   compliance   requirements,   no   change   to   the   antenna   or   the   device   is   permitted.

  Any   change   to   the   antenna   or   the   device   could   result   in   the   device   exceeding   the   RF   exposure   requirements   and   void   user’s   authority   to   operate   the   device.

 

FCC   INFORMATION  

  The   Federal   Communication   Commission   Radio   Frequency   Interference  

Statement   includes   the   following   paragraph:  

 

  The   equipment   has   been   tested   and   found   to   comply   with   the   limits   for   a   Class  

B   Digital   Device,   pursuant   to   part   15   of   the   FCC   Rules.

  These   limits   are   designed   to   provide   reasonable   protection   against   harmful   interference   in   a   residential   installation.

    This   equipment   generates,   uses   and   can   radiate   radio   frequency   energy   and,   if   not   installed   and   used   in   accordance   with   the   instruction,   may   cause   harmful   interference   to   radio   communication.

    However,   there   is   no   grantee   that   interference   will   not   occur   in   a   particular   installation.

    If   this   equipment   dose   cause   harmful   interference   to   radio   or   television   reception,   which   can   be   determined   by   turning   the   equipment   off   and   on,   the   user   is   encouraged   to   try   to   correct   the  

  interference   by   one   or   more   of   the   following   measures:  

‐‐ Reorient   or   relocate   the   receiving   antenna.

 

‐‐ Increase   the   separation   between   the   equipment   and   receiver.

 

‐‐ Connect   the   equipment   into   an   outlet   on   a   circuit   different   from   that   to   which   the       receiver   is   connected.

 

 

‐‐ Consult   the   dealer   or   an   experienced   radio   /   TV   technician   for   help.

 

The   user   should   not   modify   or   change   this   equipment   without   written   approval   from  

United   Integrated   Services   CO.,   LTD.

  Modification   could   void   authority   to   use   this   equipment.