United Integrated Services XBTSMT-230 WirelessMotion Sensor User Manual

Wireless Motion Sensor User's Manual

Product Name : Wireless Motion Sensor

Model No : SMT-230

Input Power: 4.5V DC(Battery) / 5V/1A(Power Adaptor)

Features Description:

1.

The use of Infrared Motion Detection of sensor detector, it self cannot transmits light wave of the infrared.

2.

The use of three UM-3 AA 1.5V alkaline batteries ， battery power is insufficient to inform the host will automatically operate a very low power, the battery can be used for more than one years.

3.

Easy link, when install at the first time to press the set button on the side of product

Joining with Gateway 、 Panel Coordinator or Route.

4.

Can use the WPW-220 (Wireless Power Controller) do so with even control, For example: Corridor night auxiliary lighting.

。

5.

When the device is connected to the power supply, it will automatically cut off the battery power.

6.

This device must be compatible with Gateway using, if beyond the effective reception distance will not be used.

Outline Dimensions:

Installation Hints:

1.

First use UM-3 AA 1.5V alkaline batteries into SMT-230 (Wireless Motion Sensor) battery holder, and check the battery positive and negative polarity marked is correct.

2. The SMT-230 (Wireless Motion Sensor) by pressing the SET button at the side, and then press the Gateway 、 Panel Coordinator or Route at the bottom of the SET button, Wait for 1 second to 15 seconds. If green LED indicator light flash and long light that means linking success. If green LED indicator light flash and red LED long light that means fail.

3. The SMT-230 (Wireless Motion Sensor) p laced on the need to detect the channel next to ， n eed to pay attention to the Wireless Motion Sensor detector window, do not be put into place where the sun, and not on where the ambient temperature is too high.

4. Can use the SMT-230 (Wireless Motion Sensor) signals through the Panel Coordinator, on the Wireless Power Controller do so even control. Join to link with Gateway, please reference user manual of Wireless Panel Coordinator).

Troubleshooting:

1.

Problem:

When link with Gateway 、 Panel Coordinator or Route, there is no display of green LED indicator light flash and long light for SMT-230 (Wireless Motion Sensor to flash two or three times.

Solution:

a. Need to make sure the battery is good there is electricity, the installation of the battery positive and negative direction is correct.

b. May be not press set button, need to link with Gateway 、 Panel

Coordinator or Router again.

c. If the above handles are invalid, please contact with agency.

2.

Problem:

Unable to link with Gateway 、 Panel Coordinator or Router.

Solution:

a. It needs to confirm the distance between SMT-230(Wireless Motion Sensor) and Gateway 、 Panel Coordinator or Route . Wireless connects in non-camouflage straight line effective range 10 meters.

May pull closer between booth's distance tests to have a look first, whether to have the improvement segment condition

Specification:

:

Model No.

UIS/Wireless Motion Sensor

SMT-230

Electrical Specification

Transmit Frequency

Detection Mode

Operation Range

2.4GHz ISM band, IEEE802.15.4: 2405 ~

2480MHz

Passive Infrared

Up to 200 meters (LOS)

AC Adapter

Battery Type

Battery Life

Sensor Detection Range

Input : AC 100 ~ 240V , 47 ~ 63Hz at

0.19A MAX

Output : DC 5V/1A 5W MAX

AA Alkaline battery x 3 up to 3 year

8 M 25°C, Angle 110,

LED Indicator Red

Environmental Requirement

Operating Temperature

Storage Temperature

0°C to 40°C

-10°C to 55°C

Humidity

Mechanical Specification

90% RH Max., Non-Condensing

Dimension (WxHxD, mm) 86.3*53.1*71mm

Weight (w/o Battery) 78g

Notice : The changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. No change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.