advertisement
High Resolution / Day&Night
COLOR BOX CAMERA
사용 설명서
MANUAL
용 서 680 TVL
The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
INFORMATION - This equipment has been tested and found to comply with limits for a
Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
WARNING - Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
Do NOT use power sources other than that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and should conform to all local codes
■
Warning
The camera needs periodic inspection.
Contact an authorized technician for inspection.
Stop using your camera when you find a malfunction.
If you use your camera around smoke or unusual heat for a long time, fire may be caused.
Do not Install the camera on a surface that can not support it.
Unless the surface is suitable, it could cause falling or other hazards.
Do not hold plug with wet hands.
It could cause an electric shock.
Do not disassemble the camera.
It may result in fire, electric shock or other hazards.
Do not use the camera close to a gas or oil leak.
It may result in fire or other hazards.
3
■
Contents
1.Features --------------------------------- 5
2. Components --------------------------------- 6
3. Names and functions of parts --------------------------------- 7
4. Installation
5. Setup Menu Operation
6. Troubleshooting
7. Specifications
--------------------------------- 9
--------------------------------- 13
--------------------------------- 21
--------------------------------- 22
4
1. Features
■ SONY 1/3" 480K/570K-Effective Pixel Ex-view HAD CCD II
Minimum Resolution 0.1 Lux (F1.2, 50 IRE)
■ High Resolution: More than 680 TV Lines
This camera has realized high resolution of 680 TV lines using the top-notch full digital image processing, 12 Bit A/D serial signal processing and special algorithm technologies.
■ NR (Digital Noise Reduction)
The DNR technology eliminates noise thus generating a distinct and clear image.
■ High Color Reproduction
White balance processing with wide-range color temperature support and high-saturation processing.
■ DAY&NIGHT
This camera has the Day/Night function which shows clear image in dark condition
■ ATR (Adaptive Tone Reproduction)
Automatically this function compensates the darker areas surrounding the object to provide naturally sharp picture and then improves contrast in bright/dark areas
■ High sensitivity and high saturation signal
This camera increases the number of horizontal pixels and achieves a high saturation signal level and high sensitivity that extends into the near infrared.
■ Preset OSD(On Screen Display) menu (8 languages)
This camera supports the OSD function which is used with multi language. And so, the camera can be controlled via selecting text displayed on the monitor screen.
■ Privacy Zone
It has 8 privacy zone function to prefect private area. It is possible to maximum 8 areas and free to adjust masking size & area
5
2. Components
2)
3)
1)
4)
4)
COLOR CAMERA -------------
AUTO IRIS LENS CONNECTION
PLUG
C-MOUNT ADAPTOR
L-WRENCH
-------------
-------------
-------------
MANUAL -------------
6
3. Names and Functions of Parts
1) Front
① Lens protection cap
Please cover the lens when not using it.
② CS-Mount lens adaptor
Please attach the CS-Mount lens here.
③ Back Focus clamp screw
Please loosen the clamp screw with a screwdriver before adjusting the Back Focal length.
☞ Mounting bracket screw hole
Please use the screw hole when fixing the camera onto the mounting bracket. Please use the clamp screw as specified picture.
☞ The mounting bracket can be separated and attached to the top of the camera.
In this instance please do not tighten the screw to a depth of more than 5mm, otherwise serious damage can occur to the inside of the camera.
7
2) Back
① Auto iris lens connector
This is the connection terminal for the auto iris lens.
② Video output terminal
Sends video signals and connects to the video input terminal of the monitor.
③ Power lamp
Lights up when the correct power is supplied to the camera.
④ Setting button
SETUP button : Used for the menu display. This button can be used to confirm settings after changing the value of the selected function or current conditions.
UP & DOWN buttons : Used for selecting items by moving the cursor up or down on the menu screen.
LEFT & RIGHT buttons
: Used when changing item values, by moving the cursor to the left or right on the menu screen.
⑤ Power input terminal
Connects to the power appropriate to each power requirement.
⑥ Auto Iris Switch
Video or DC
☞ Make sure that user can’t use video type lens using high voltage camera.
8
4. Installation
1) Lens
Lenses are sold separately. Lenses such as auto iris lens, CS-Mount lens and C-Mount lens can be used.
Note)
• Use of the DC auto iris lens is recommended to achieve the best results for operating this product effectively.
• Please keep the lens clean.
• Any foreign objects and finger marks on the lens can cause inferior image quality in low light level conditions.
① When using an auto iris lens
- Please peel off about 8mm of the outer skin of the auto iris lens cable.
- Please peel off about 2mm of the outer skin of the insulated conductor inside the lens cable
- Please remove the cover of the auto iris lens connection plug and solder the lens cable to the connector pin in the plug.
Pin No.
No.1 Pin
No.2 Pin
No.3 Pin
No.4 Pin
LENS
DC VIDEO
Damping-
Damping+
Drive+
Drive-
Red(power)
NC
White(video signal)
Black(GND)
9
- Please replace the auto iris lens connection plug cover and take off the lens protection cap, and then attach the auto iris lens to the camera by screwing it in clockwise.
- Please insert the connection plug that is connected to the auto iris lens cable into the auto lens connector, which is located on the back of the camera
- Please set the lens selection switch, located on the back of the camera, to DC or
VIDEO depending on the type of auto iris lens which is being used.
Caution
Make sure that user can’t use video type lens using high voltage camera.
10
② When using a CS-Mount lens
Please take off the lens protection cap and attach the CS-Mount lens to the camera by screwing it in clockwise.
③ When using a C-Mount lens
- Please take off the lens protection cap and attach the C-mount adaptor.
- Please attach the C-Mount lens to the camera by screwing it in clockwise.
-
Note)
• Please use the specified lens connection parts as shown in the picture below.
The use of the wrong sized parts may cause damage to the inside of the camera or result in poor fitting.
• Use of a lens which is too heavy affects the balance of the camera and may cause a
11
malfunction. Please use a lens that weighs less than 450g.
2) Connecting to a monitor
Please connect the video output terminal located on the back of the camera to the monitor.
• The connection method varies depending on the type of monitor and accessories.
Please refer to the user's manual for each instrument.
• Please turn off the power when connecting
.
3) Connecting to power
DC Power Type (DC 12V, 500mA), Dual Type, Free Voltage Type
12
5.
Setup Menu Operation
• Please press the SETUP button to set OSD menu. The SETUP menu is displayed like under the picture on the monitor.
• if it has been selected. You may move up/down to use another function by up/down buttons and change the status by pressing left/right buttons.
• After finishing all desired setting, Please select 'EXIT.
Note) If ‘ ’ appears at the mode you wish to operate, it means that there is a sub-menu which can be selected by pressing the SETUP button.
LENS
SETUP MENU
LENS AUTO
SHUTTER/AGC AUTO
WHITE BAL ATW
BACKLIGHT OFF
PICT ADJUST
ATR OFF
MOTION DET OFF
NEXT
EXIT SAVE ALL
This menu is used to select kind of the lens.
• DC
- DC: Please select, when you use DC auto iris lens
- VIDEO: please select, when you use video iris lens
• MANUAL: please select, when you use manual lens
• MODE
- AUTO: The mechanical iris is controller automatically
CLOSE: The mechanical iris is fixed to close
OPEN: The mechanical iris is fixed to open
• SPEED: Set the convergence speed of the mechanical iris
SHUTTER/AGC
SETUP MENU
LENS AUTO
SHUTTER/AGC AUTO
WHITE BAL ATW
BACKLIGHT OFF
PICT ADJUST
ATR OFF
MOTION DET OFF
NEXT
EXIT SAVE ALL
You can select either auto or manual shutter.
This function is used to set AE or ME.
13
•AUTO
(HIGH LUMINANCE)
- AUTO IRIS
Select this to control the shutter speed automatically.
-SHUT+AUTO IRIS
Select AE control on the medium and high brightness side
-Brightness
Select the high and medium brightness side reference
( LOW LUMINANCE)
-AGC
Select AE control on the low-brightness side
-Brightness
Select the low brightness side reference
• MANUAL
- MODE (SHUT+AGC)
“SHUT + AGC" is the only option available for the ME operation mode.
There are no other options.
-SHUTTER
Sets the ME shutter speed.
(1/60(1/50),1/100(1/120),1/250,1/500,1/1K,1/2K,1/4K,
1/10K)
-AGC
Sets the AGC value [dB] for ME
(6.00/12.00/18.00/24.00/30.00/36.00/42.00/44.80)
WHITE BAL
SETUP MENU
LENS AUTO
SHUTTER/AGC AUTO
WHITE BAL ATW
BACKLIGHT OFF
PICT ADJUST
ATR OFF
MOTION DET OFF
NEXT
EXIT SAVE ALL
This function is used to set the white balance operation made.
•PUSH: All pull-in
•PUSH LOCK: Hold
•ANTI CR: Color rolling suppression
14
• ATW
•
•
USER1
USER2
• MANUAL
- SPEED
Adjusts the pull-in speed ATW
- DELAY CNT
Sets the time-based hysteresis of ATW
- ATW FRAME
Sets the pull-in frame magnification
- ENVIROMENT
Sets the pull-in frame(indoor/outdoor)of ATW
- B-GAIN
Used for operating the B gain in the WB fixed gain mode
-R-GAIN
Used for operating the R gain in the WB fixed gain mode
-B-GAIN
Used for operating the B gain in the WB fixed gain mode
-R-GAIN
Used for operating the B gain in the WB fixed gain mode
-LEVEL
Sets the B and R gain values for manual WB
(0-255)
15
BACKLIGHT
SETUP MENU
LENS AUTO
SHUTTER/AGC AUTO
WHITE BAL ATW
BACKLIGHT OFF
PICT ADJUST
ATR OFF
MOTION DET OFF
NEXT
EXIT SAVE ALL
• OFF
Backlight compensation OFF
• BLC
Backlight compensation ON
• HLC
High light compensation ON
PICT ADJUST
SETUP MENU
LENS AUTO
SHUTTER/AGC AUTO
WHITE BAL ATW
BACKLIGHT OFF
PICT ADJUST
ATR OFF
MOTION DET OFF
NEXT
EXIT SAVE ALL
•MIRROR: Sets the horizontal flip for display output
•BRIGHTNESS: Sets the screen brightness
•CONTRAST: Sets the screen contrast
•SHARPNESS: Sets the screen sharpness
•HUE: Adjusts the hue
•GAIN: Adjusts the gain
ATR ( Adaptive Tone Reproduction)
SETUP MENU
LENS AUTO
SHUTTER/AGC AUTO
WHITE BAL ATW
BACKLIGHT OFF
PICT ADJUST
ATR OFF
MOTION DET OFF
NEXT
EXIT SAVE ALL
Automatically this function compensates the darker areas surrounding the object to provide naturally sharp picture and then improves contrast in bright/dark areas
16
•LUMINANCE
Sets the extent of the luminance compression
(LOW/MID/HIGH)
•CONTRAST
Sets the extent of the contrast enhancement
(LOW/MIDDLE/MID/MIDHIGH/HIGH)
MOTION DET
SETUP MENU
LENS AUTO
SHUTTER/AGC AUTO
WHITE BAL ATW
BACKLIGHT OFF
PICT ADJUST
ATR OFF
MOTION DET OFF
NEXT
EXIT SAVE ALL
•DETECT SENSE: Sets the motion detection sensitivity
•BLOCK DISP OFF: Controls the ON/OFF status of the motion detection block display
• BLACK DISP ENABLE:
The display switches to the "dead band setting" screen when the Enter operation input is performed from the ENABLE selected status.
To come back previous menu, Press SET button during 3 seconds
•MONITOR AREA OFF:
Sets whether to use the monitoring frames
OFF: The monitoring frames are not used
ON: The monitoring frames are used
•AREA SEL
Monitoring frame 0 / Monitoring frame 1 / Monitoring frame 2 / Monitoring frame 3
•TOP
Set the top side of the monitoring frame selected by the AREA SEL parameter.
•BOTTOM
Set the bottom side of the monitoring frame selected by the AREA SEL parameter
•LEFT
Set the left side of the monitoring frame selected by the AREA SEL parameter.
17
•RIGHT
Sets the right side of the monitoring frame selected by the AREA SEL parameter
PRIVACY
SETUP MENU
PRIVACY ON
DAY/NIGHT AUTO
NR
CAMERA ID OFF
SYNC INT
LANGUAGE ENGLISH
CAMERA RESET
BACK
EXIT SAVE ALL
•AREA SEL: Selects the mask frame to be adjusted
•TOP: Sets the top side of the mask frame selected by the AREA SEL parameter
•BOTTOM: Sets the bottom side of the mask frame selected by the AREA SEL parameter.
•LEFT: Sets the left side of the mask frame selected by the AREA SEL parameter.
•RIGHT: Sets the right side of the mask frame selected by the AREA SEL parameter
•COLOR: Sets the colors of the mask frames
•TRANSP: Sets the transparency ratio of the mask frames.
•MOSAIC: Sets the mask frame mosaic to ON or OFF
DAY/NIGHT
SETUP MENU
PRIVACY ON
DAY/NIGHT AUTO
NR
CAMERA ID OFF
SYNC INT
LANGUAGE ENGLISH
CAMERA RESET
BACK
EXIT SAVE ALL
You can display pictures in color or black and white.
When the SETUP menu screen is displayed, select
‘DAY/NIGHT’ by using the UP and DOWN buttons so that the arrow indicates “DAY NIGHT”.
Please select the mode you wish to operate by pressing the LEFT or RIGHT button.
• AUTO
The mode is switched to ‘Color’ in a normal environment, but switches to ‘B/W’ mode when ambient illumination is low.
18
-BURST
Burst signal OFF enable, Burst signal ON
-DELAY CNT
Sets the Night/Day identification transfer time
-DAY → NIGHT
Set the threshold for identifying the Night status from the Day status.
-NIGHT → DAY
Set the threshold for identifying the Day status from the Night status.
• B/W
-BURST
Burst signal OFF enable, Burst signal ON
• COLOR
The picture is always displayed in color.
NR
SETUP MENU
PRIVACY ON
DAY/NIGHT AUTO
NR
CAMERA ID OFF
SYNC INT
LANGUAGE ENGLISH
CAMERA RESET
BACK
EXIT SAVE ALL
The function is used to set the noise reduction
-NR MODE
OFF
Y:Y filter ON
C: filter ON
Y/C:Y and C filters ON
-Y LEVEL
Set the Y filter strength.
-C LEVEL
Set the Y filter strength.
19
CAMERA ID
SETUP MENU
PRIVACY ON
DAY/NIGHT AUTO
NR
CAMERA ID OFF
SYNC INT
LANGUAGE ENGLISH
CAMERA RESET
BACK
EXIT SAVE ALL
The function is used to set the camera ID
• ON
Camera ID display OFF
• OFF
Camera ID display ON
• ↑↓→ ←
The camera ID cursor moves
• CLR
The character selected by the camera ID cursor is cleared
• POS
The display switches to the camera ID display position setting screen
SYNC
SETUP MENU
PRIVACY ON
DAY/NIGHT AUTO
NR
CAMERA ID OFF
SYNC INT
LANGUAGE ENGLISH
CAMERA RESET
BACK
EXIT SAVE ALL
• INT
Internal mode
• LL
Line lock mode
LANGUAGE
Select the language in which to display the internal OSD menu.
ENGLISH, JAPANESE, GERMAN, FRENCH, RUSSIAN, PORTUGUESE, SPAINS,
CHINES
CAMERA RESET
All the internal OSD menu settings are initialized.
20
6.
Troubleshooting
If there are problems in operation, please refer to the items below. If the problem persists, please contact the agent you purchased this product from.
Problems
Nothing appears on the screen.
Troubleshooting
• Please check the power connection.
The video image is not clear.
• Please check the video signal line connection.
• Please check if the lens is clean.
Please clean the lens with a clean cloth or brush.
• Please adjust the contrast feature of the monitor.
The screen is dark.
Colors are not quite right.
The screen is flickering.
There is a problem with the camera operation.
The MOTION DETECTION function is not working.
COLOR mode is not working.
• Please readjust the back focus of the camera.
• Please adjust the contrast feature of the monitor.
• If you have an intermediate device, set the 75 / Hi-z properly, and check the terminals.
• Please check if an auto iris lens is being used and adjust the brightness level.
• Please check if an appropriate power source to the camera complies with the manufacturer's standard requirement, or if the voltage keeps changing.
• Please check if 'MOTION DETECTION' mode is turned on.
• Please check the setting of the MD AREA.
• Please check the 'WHITE BAL' setting
• Please check if the camera is facing directly into sunlight or fluorescent light.
• Please check if an auto iris lens is being used.
• Please check the connection of the lens connector cable.
• Please check if the AGC menu is set to the OFF position.
21
7. Specifications
SIGNAL SYSTEM
IMAGE SENSOR
TOTAL Pixels
Effective Pixels
RESOLUTION
Syns. Inter. H/V
Shutter Speed
MIN. ILLUMINATION(F1.2)
DAY & NIGHT
High Speed Shutter
WHITE BALANCE
BLC / HLC
AGC
Privacy Zone & Motion Detection
ATR
Camera ID
S/N RATIO
VIDEO OUTPUT
SYNC. SYSTEM
OSD
DNR
LENS Mount
Operating Humidity
OPERATING TEMP.
Dimension
WEIGHT
SUPPLIED VOLTAGE
POWER CONSUMPTION
Power Supply
NTSC PAL
Sony 1/3" 480K/570K-Effective Ex-view HAD CCD Ⅱ
1020(H) × 596(V)
976(H) × 494(V)
1020(H) × 596(V)
976(H) × 582(V)
680 TV lines
15.734/ 59.94Hz
1/60~1/100,000 sec
15.625K/50Hz
1/50~1/100,000 sec
0.1Lux (50IRE)/0.02Lux(15IRE)
B/W:0.08Lux(50IRE)/0.002Lux(15IRE)
D&N Function by Digital Change : COLOR / AUTO / B/W
TDN with ICR (Optional)
1/60(1/50)~1/10K sec
ATW / PUSH / USER1 / USER2 / ANTI CR / MANUAL /PUSH LOCK
ON / Off
Level setting
OFF / ON (Motion:4 Zones, Privacy:8 Zones)
On / Off
On / Off
More than 52dB
Composite video output 75 ohm terminated
Internal
Available
OFF / ON(2D)
C / CS Mount
30% ~ 90% RH
- 10
℃
to 50°
61(W) × 55(H) × 104.7(D)mm
About 420g
DC 12V, 50/60Hz (Option: dual volt)
Max. 150Ma
DC 12V (10.2V~14.5V)
Dual Voltage : AC24V / DC12V
High Voltage : AC 90V~250V 50/60Hz
22
23
advertisement
Related manuals
advertisement