XIEGU G90 Operation Manual

Xiegu G90 is a portable, 20W HF amateur radio transceiver with a built-in automatic antenna tuner and detachable display unit. It boasts a 24-bit data size @48kHz sampling rate, configurable function experience, and excellent transmit performance with a high-performance front-end narrowband ESC preselector. With a frequency range of 0.5~30MHz, it offers SSB/CW/AM/FM*1 working modes.

ಪಿಡಿಎಫ್

ದಾಖಲೆ

ಜಾಹಿರಾತು

XIEGUTECH

Portable SDR HF Transceiver

G90

Operation manual

Built-in automatic antenna tuner ATU

V1.00.01

Basic Feature

Panel button

Front panel Interface

Tail interface

Interface definition

M IC b u tto n

External power connection method

M e n u o p e r a t i o n

Display interface

P o w e r o n / o f f

Operating frequency bands selection

Operating MODE selection

Volume adjustment

Multifunction adjustment knob

Adjusting transmit power Po

Setting operation frequency

A T U

Function buttons

Setting SPL and VFO

CW transmission

CW Auto pager

Standing wave scanner SWR

Digital filter

Line Input / Output selection

Channel Memory MW

2 0

1 2

1 3

Catalog

Pre-channel naming TAG

Boot interface call sign setting CALL

Connect to a computer for data communication 32

System parameter setting 33

Computer control instruction 33

Bands voltage parameter

Performance parameter

Packing items

G90 and XPA125B connection diagram

CE-19 expansion card interface

Basic feature

G90 is a portable 20W HF amateur radio transceiver with an SDR architecture with built-in auto antenna tuner. The display unit and the radio can be separated. It is a new member of the Xiegu product family and the first model of the G series.

24-bit data size @48kHz sampling rate, it has excellent transmit performance and a highly configurable function experience; 。



High performance front end narrowband ESC preselector;



Covers the frequency range of 0.5~30MHz, SSB/CW/AM/ FM

*1 three working modes;

 1.8 inch high brightness color TFT LCD screen;

 ±24k bandwidth spectrum display, waterfall display;

 Software defined narrowband filter(CW mode: 50Hz);

 detachable display unit;



Up to 20W of RF power;

 Built-in wide range automatic antenna tuner;

 Diversified interfaces, In particular, the baseband I/Q output allows it to interface with any external device that can handle baseband I/Q, including sound card-based or PC-based applications such as XDT1.

In order to better experience this device, please read this manual carefully before use to fully understand the operation method of G90.

*1: The FM mode can only be turned on when the GSOC controller is used together.

5 6

Ci90

7 8

H F TRANSCEIVER rn

, {I f m>

·

SDR @

Volume knob

 Turning ， + / – the volume.

 Short press ， Switch to headphone output mode.

2 Power/ Receive or transmitting status pilot lamp.



Standby/receive status, showing yellow-green;

 transmitting status ， showing red;

3 Power switch

 In the off state ， press it to boot.



In the on state ， hold press it to shut down 。

4 Multifunction adjustment Knob

 By default, turning this knob will stepping at 100 kHz.



Press and hold this knob to switch to the Select

Custom function.

5 ～ 6 Mode switching

Mode switching

7 ～ 8 BAND Switching

Band switching

9 FUNC pilot

This pilot will light when the second function of the button is operated.

10 △ F Pilot

11 Main Knob

Operating this knob will change the current frequency.

Panel button

12 Function button

Button definitions and functions are detailed in the operation section.

20 MIC Interface

On the right side of the machine-head

Connecting the multi-function MIC to this connector.

21 headphone interface

On the left side of the machine- head

This 3.5mm stereo jack (3-pin) for connecting headphones.

22 Self-defining(communication) interface

On the left side of the machine-head

Firmware update for the machine-head (Controller), or other features.

Tail plate interface

13 Antenna interface

SL16-K type ， impedance 5

0Ω 。

14 KEY interface

The interface is a 3.5mm stereo jack for connection to manual/automatic telegraph keys.

Telegraph key connection diagram, as shown ：

Manual telegraph keys ， It is

Necessary to connect "di( 滴 )"

And "da （嗒） " together.

15 COMM interface

Using for the case firmware updates.

。

16 I/Q Signal output

The interface is a 3.5mm stereo jack for

“I/Q” signal output.

17 ACC

The interface is an 8-pin mini DIN interface, as defined in the interface definition.

18 DC power interface

External DC power input interface.

The round hole is "-", the square hole is "+".

19 Ground terminal

、

MIC interface

MICE

MIC

GND

MDATA

MIC

、

COMM Connector

RXD

TXD

、

Headphone interface

信号

Note: 信号（signal）

GND

PTT

MSVSW

+8V

4、

ACC interface

GND

+8V

ALC

BAND i

5、

Telegraph key wiring diagram

Note:滴（di）嗒（da）公共（ common

）

DATA

AF_OUT

AF_IN

PTT

Hand MIC

1 、 LOCK

2 、 PTT

3 、 UP / DOWN

4 、 Receive/transmit indicator

5 、 Numeric keypad

Lock button

Transmit control button

Frequency "+" or "-" buttons

Hand Mic operation indicator

6 、 FIL

Numeric keypad area

7 、 MODE

8 、 Function indicator

9 、 Function button

10 、 MW

Filter selection

Case operation mode

F1/F2 self-defining setting button

11 、 V/M

12 、 XFC

13 、 TUNER

Storage operation

Frequency/channel switching

Hold press to turn on the built-in automatic antenna tuner for tuning.

The G90 can use a 13.8V external DC power supply. The DC power supply has a current load capacity of at least 10A. The supplied power cord can be used to connect radio and DC power.

When connecting the DC power supply, please carefully connect according to the following figure to avoid reverse polarity of the power supply.

The red wire is connected to the positive pole of the power supply, and the black wire is connected to the negative pole of the power supply .

Note:

黑线（ black wire

）红线（ red wire

）

;

Operating

When the G90 uses an external power supply, in order to prevent external interference from entering the radio through the power line or the radio frequency interference in the radio is radiated outside through the power line, we can put the EMC magnetic ring on the power line. Install the magnetic ring as close as possible to the side of the power plug.

The power cord wraps around the magnetic ring 2 turns.

As close as possible to the plug.

 When using an external power supply, carefully check the polarity of the power cord and do not reverse the polarity.

 The limited warranty of this radio does not include damage caused by an external power connection error or damage caused by improper power supply voltage.

External power connection

The G90 uses the Quick Mode button operation to use or turn off various functions. All functions are distributed on each function button (or in the second function). All functions are turned on or off or adjusted and displayed or reminded in the corresponding area on the screen.

。

Interface display as follows ：

Main frequency

Status Display

Mode

VOF status

S-table and power mete

Input voltage

Volume

Functions display

Standing wave

Signal level

Waterfall image display

Operating

Hi Dear friends.

In order to let you master the functions and proficiency of the G90 portable transceiver ASAP, please read the operation guide of this manual to understand the powerful functions of the G90. Go ahead now!

Turn on/off Transceiver

1 、 Turn on ： press button.

2 、 Turn off ： Power on state ， Hold press

Turn off screen operation:

In the power on state, tapping the switching

Button to turn off the screen display.

The other units are still working.

Pressing any button or turning the

Knob will wake up the screen display. button1 second 。

Power button

Operating

Operating frequency band selection

The G90's frequency range covers 0.5 to 30

MHz. Amateur frequencies within this range are divided into multiple bands, and band switching can be performed in a number of

+ - different ways.

Operation method:

Press the BA ND’s < or > button ， Switch to the next or previous operating band separately.

1.8MHz 3.5MHz 5.2MHz 7.1

MHz 10MHz 14MHz

28MHz 24MHz 21MHz 18MHz



Each amateur band has a user-defined frequency band that can be used temporarily, when the band is switched, you will see this custom band.



Whether the 60-meter band is open, it depends on the different laws of different countries (or regions).

 Different versions of the machine have different frequency divisions, depending on the laws of different countries

(or regions).



VFO-A and VFO-B are two independent VFO modes that can be set to different operating states. Check [VFO

Settings] please.

Operating

Operating mode select

Press [ MODE ] button ， In all modes ， according to the following fixed order switching

Mode left loop

 The FM mode can only be turned on when used with the GSOC controller.

Mode right loop

Operating

VOLUME CONTROL

Speaker mode ：

Rotate the volume knob left or right to adjust the size of the output volume.

Headphone mode ：

 Press the volume knob short to enter headphone mode.

 Rotate the volume knob left or right to adjust the size of the headset volume.

VOX mode on / off ：

Press and hold the volume knob for 3-second to turn the VOX feature on or off.

This feature has not been activated yet.



When using the AF in/out Port of the ACC interface, set the relevant volume size in the system menu.

Operating

Multifunction adjustment knob

The multifunction knob provides several operation options and can customize features.

Operation method ：

Default: Stepping of 100 kHz frequency bits.

Multi-function adjustment

Short press: Enter SQL item to adjust SQL noise depth.

Hold press ： Go to the User Custom feature menu, rotate

The main knob to select the appropriate function, and short press the “SAVE” key to determine that the feature is selected.

At this point, the feature is projected onto the [multifunction adjustment knob].

The customizable features are as follows:

1) Frequency 100k, stepping 100k

2) SQL Level, squelch setting

3) Po Level, transmit power setting

4) Key Speed, automatic key rate setting

5) FFT Scale, spectrum reference level setting

Adjustment transmitting Po

Operation method ：

1 、 Short press the [Po] button to enter the

Operating

PO power setting state, the right side of the screen function display area will

Multi-function

Adjustment knob display the power settings number.

2 、 Rotate [multifunction adjustment knob] for power setting with stepping

1W 。

 When using the G90 transceiver for the first time without understanding the current antenna state, minimize the set transmit power value.

Set the operating frequency

There are two ways to set the G90 operating

Operating frequency, which is to use the main knob and multifunction handle to set the frequency.

。

Operating method ：

1 、 Set the frequency using the main knob



Short press the main knob, select 100Hz,

Main Knob

1kHz, 10kHz Stepper.



Rotate the main knob to set the frequency of the current step.

、

Set the frequency using the multifunction handle

 Press the [F-INP ENT] button on the handle, G90 enter the frequency setting state, the cursor will blink in the first position on the left side of the frequency display bit;



Enter the frequency values you want to set, and then press the [F-INP ENT] button again to complete the frequency setting.

For example, set the current frequency to 14.09000MHz, and the key order is as follows:

1. First press the [F-INP ENT] button;

2. Press the 1 4 . 0 9 0 0 0 number key in sequence;

3. Press the [F-INP ENT] button again, complete the setup.

Operating

Automatic Antenna Tuner

This G90 is integrated with an efficient automatic antenna tuner that can help you quickly set up and debug your antenna.

 Short press the [TUNE] button, will be connected to the built-in antenna tuner, the "TUNE" logo will be displayed at the top of the screen.

 When connected to the automatic antenna regulator, press the [TUNE] button for 1 seconds and the ATU auto-tuning function will be activated.

The receive status is automatically returned when tuning is complete.

Tuner

Note

1. Press the [TUNE] button and the antenna icon appears at the top of the screen to indicate that the automatic antenna tuner function is turned on. Just open, the automatic Antenna tuner tuning has not been started.

2. To use the built-in automatic antenna tuner, you must tune once after you turn on the Automatic Antenna tuner feature.

3. If you start the transmission after tuning, the

“SWR” icon will appear on the top of the screen and flash, which means

That the standing wave of the current antenna is still large and needs to be retuned.

4. When the antenna naturally resonates into the current band, be sure to turn off the Automatic Antenna tuner feature.

5. When using a whip antenna and turning on the built-in antenna tuner for tuning, it is possible to cause strong RF interference to the native or electronic device.

Operating

Function button

Its common functions are distributed on the various function keys. Some function keys have a second function.

When the function is selected, turn the main knob to adjust the value.

Operation of the second function:

 Press the [FUNC] button at first, the “F” indicator will light, then press the corresponding function button.

 Press the [FUNC] button again to exit the second function. At this time, the “F” indicator is off.



In any function (including the second function of FUNC), press the main knob to exit the function settings and return to the main interface.

Button function table

Button Func1 (press cycle

PRE/ATT

CMP/F-L

NB/F-H

AGC/SPL

VM.

MW/MC

A/B.A>B

TUNE

POW

KEY

LOCK

PRE--ATT-- direct connection

Turn on transmit voice compression

Turn on pulse interference canceller

AGC-、 AGC-S 、 AGC-F 、 AGC-A cycle

Switch frequency mode or channel mode

Turn on channel storage

Switch between VFO-A and VFO-B

Turn on/off the antenna tuning function

Operating

POWER Transmit power setting

SWR THR Standing wave protection threshold

SPEED Automatic key rate setting

M/L/R Manual/automatic left and right mode switching

MODE

QSK iambic A/B Mode switching

Insert/not insert selection

QSK Time Insert time setting

5-level screen backlight brightness setting

Func2 FUNC+)

Digital filter F-L low-end frequency selection

Digital filter F-H high-end frequency selection

Turn on split frequency transceiver operation mode

To be determined

Turn on channel clear mode

Copy the current VFO to the background VFO

MIC GAIN

INPUT

MIC gain setting

Voice input selection

Side-tone volume setting CW Volume

CW TONE Side-tone frequency setting

SCALE Spectrum reference level setting

Hold press

Start antenna tuner tuning

Lock button, knob

Operating

Split frequency transceiving operation SPL and VFOA/B settings

There are two independent VFOs inside the G90 transceiver. We can set different frequencies and modes separately. With the SPL function, it is convenient to realize the split transceiving operation.

VFO setting ：

、

Press the [A/B / A>B] button to switch between VFO-A and VFO-B.

2 、 When switching to a certain VFO state, you can set the current VFO's operating

VFO operation frequency, mode and other settings.

Split frequency transceiver SPL operation method:

1 、 Set the receiving frequency and mode (VFO-A) first;

SPL operation

2 、 Then setting the transmit frequency and mode (VFO-B);

3 、 Operate the second function of the [AGC/SPL] button,

4 、 Turning on the SPL function to turns on the split transceiver mode.

。

 You can make full use of VFOA/B to set different frequencies or modes, and switch between two frequency points in real time.

Operating

CW communication

Operate with a hand key or an external key controller device.

Operation method:

1 、 Insert the key body (three-wire) plug into the KEY interface;

2 、 Press the [MODE] button to switch the mode to CW (or CWR);

3 、 Open the QSK function in the [KEY] button function and set the appropriate QSK time; ；

4 、 Press the CW button to perform CW communication.

Key button

The [KEY] button function contains adjustment

Practice mode ：

You can use the G90 as a CW code trainer.

The operation method is as follows: In the [KEY] button function, the QSK function is turned off. In this state, when the button is pressed, the transceiver has a CW side tone, but Does not emit signals externally.

items that are commonly used when doing CW communication: ：



SPEED

 K-R/L

 Iambic A/B

 QSK

Operating

CW automatic caller MSG1~MSG3 (Not yet opened, need to be used with GSOC controller)

The G90 host provides 4 sets of CW preset telegraph text storage for automatic call in CW mode.

Operation method:

To be determined

Operating

Standing wave scanner SWR (Not yet opened)

G90 host has an antenna standing wave scanning function, which can scan the standing wave parameters of the current antenna, and is convenient for the user to adjust the antenna.

。

Operation method ：

1、

Operate the second function of the [Po] button to start the standing wave scan;

2、

After the scan is completed, the scanning process is automatically exited.

 The scanning result of the standing wave scanner may have a certain error, for temporary use only. For accurate measurement of antenna standing wave data, use a professional antenna analysis device for measurement.

Operating

Digital filter

The G90 has a built-in variable digital filter that implements a narrowband filter function to improve signal identification.

Operation method ：



Operate the [CMP/F-L] button and the second function of the [NB/F-H] button;

 Rotate the main knob to adjust the lower limit of the digital filter frequency and the upper limit of the frequency respectively until the user experience is appropriate;



You can adjust the filter parameters according to your own listening preferences to get the best experience.

Operating

Line input/output

The G90 has an external line input interface. When communicating with a computer or an external modem for data communication, the corresponding input/output items should be correctly selected.

Operating method ：

 In the system menu, using ACC port line input, select: AUX LINE IN. Set the appropriate input volume.

 In the system menu, select: AUX AFOUT VOLUM to set the appropriate output volume 。



When digital communication is in progress and audio input is made using the ACC port, make sure that the volume of the line input is sufficient.

Operating

Channel storage MW, clear MC

Channel storage ：

1. In the VFO mode, adjust the required frequency, mode, advanced function status and other parameters;

2. Press the [ MW/MC ] button to start the channel storage operation;

3. Rotate the main knob to select the channel number to be stored, and short press the main knob to complete the channel storage;

4. If the current channel has stored information, using this channel number for storage again will clear the previous channel information and save the current channel information.

Bring up the storage channel:

1 、 If you press the [VM] button on the panel in VFO mode, you will enter channel mode;

2 、 Rotate the main knob to switch the current channel.

Clearing channel storage:

1. In the channel mode, operate the second function of the [MW/MC] button to start the channel clear function;

2. At this point, the channel number starts to flash. Rotate the main knob to the corresponding channel number and press the main knob to complete the channel clear.

Operating

Channel naming TAG (need to be used with GSOC large screen controller)

Stored channels can be named with "tags" consisting of letters and numbers.

Operating method ：

To be determined.

Operating

Boot interface call sign setting CSN

The G90 can set the call sign information displayed on the boot interface.

Operating method ：

1. Press and hold the [FUNC] button to go to the system setup menu and select the [CALL SIGN] function to go to the call sign editor;

2. Under the editor, after editing the call sign, save the set text content and return to the normal operation state;

4. When you turn it on again, the boot interface will display the call sign you edited.

Operating

Connect to a computer for amateur radio data communication

The G90 transceiver can be connected to a computer to perform various data communication with the corresponding computer software.

Operation connection method:



Connect the computer audio output/input to the G90 from the ACC port (MINI-DIN8).

 Insert the data cable into the COMM port, connect the G90 to the computer, and ensure that the computer driver of the data cable is installed correctly. The PC software can control the G90 transceiver;

 Adjust the volume of G90 and the input/output volume of ACC port to the appropriate one. Observe the software interface to avoid the Audio frequency amplitude being too large and unable to communicate.

 Select the corresponding working mode to perform data communication.

 In order to prevent interference, the radio and computer must be well grounded. Please install the EMC magnetic ring for the data cable and audio cable, and install it as close as possible to the radio.

Computer control instruction

The G90 uses the standard CIV instruction set. You can use the standard instructions of this instruction set to remotely control the transceiver. It can also be used to configure the control instructions of other software to control the G90.

Band voltage data

The G90's ACC port provides band data for each band. The band data can control the peripheral to automatically switch the band or share the band information with other devices.

Band Voltage Band Voltage Band Voltage Band Voltage

1.8MHz 230mV 7MHz 920mV 18MHz 1610mV 28MHz 2300mV

3.5MHz 460mV 10MHz 1150mV 21MHz 1840mV

5.0MHz 690mV 14MHz 1380mV 24MHz 2070mV

Performance parameter

General parameters

Frequency Range ： receive ： 0.5MHz

～ 30MHz transmitting ： 160M ～ 10M Amateur radio band only

） transmitting mode ：

A1A(CW) ，， F3E(FM)

Mini step ： 10Hz

Antenna impedance: 5

0Ω

Range of operating temperature ： 0

℃ ～ +50

℃

Frequency stability ：

±10 ppm for 10 to 60 min after power on

@25

℃ ： 1ppm/h

Voltage ： 10.5

～ 16.5V DC ， Negative ground

Electric current ： receive ： 500mA@ Max transmitting ： 8A@ Max

Case size ： 120*45*210mm （ W * H * L ）

(No protrusions)

Weight ： about 1.63kg

（ only case ）

Receiver parameters

Circuit type ： ZIF

Adjacent channel suppression ：

Sideband suppression ：

Sensitivity

：

1.0

～ 1.79999MHz

1.8

～ 27.9999MHz

28 ～ 30MHz

SSB/CW/FM

0.25uV

Transmitter parameters

RF output power ： 20W (SSB/CW/FM)

5W (AM Carrier) @13.8VDC

Modulation type ： Digital modulation

Stray radiation suppression

Carrier suppression ：

Mic impedance ：

： ≥50dB

≥40dB

200 ～ 10k conventional 600

Ω ）

≥60dB

10uV

2uV

(PRE=on ， ATT=off ， NB=off ， NR=off ， SSB/CW/AM = 10dB S/N ， FM = 12dB SINAD)

Image rejection ： 70dB

IF suppression ： 60dB

Audio output ： 0.5W （ 8 Ω ， ≤10% THD ）

Audio output impedance ： 4 ～ 16

 For the above parameters, we may make adjustments without notice.

 The operating frequency range of the transceiver will vary with the machine version, please consult your dealer.

Packing List

Item name

G90

Multi-function handle

Data cable power cable

Operation Manual

Warranty Card

Quantity

1pcs

Certificate 1pcs

* Optional accessories

Item name

CE-19

XPA125B

Description

ACC expansion adapter

100W power amplifier (with built-in antenna adjuster)

GSOC *1 G90 dedicated large screen controller

*1 The GSOC controller is expected to be available in 2019.

Connection diagram between G90 and XPA125B

G90

ACC

口

芯线

CE-19

TO XPA125

芯线

6 Pin

*note ： The 8-core ACC control line is delivered in the CE19 kit.

XPA125B

CE-19 expansion adapter interface diagram

PTT CON

TO XPA125B

AF CON

DATA CON

PTT signal / BAND signal output port. The PTT signal of this port is completely isolated from the host, providing a "low level" trigger associated with the host.

XPA12B dedicated interface.

Audio input/output port. The audio output from this port is directly output after demodulation, no filter.

Data output port in NFM mode. The two terminals of this port are in parallel relationship and both output the same signal.

ನಮಸ್ಕಾರ! XIEGU G90 Operation Manual ನೊಂದಿಗೆ ನಿಮಗೆ ಸಹಾಯ ಮಾಡಲು ನಿರ್ದಿಷ್ಟವಾಗಿ ತರಬೇತಿ ಪಡೆದ AI ಚಾಟ್‌ಬಾಟ್ ನಾನು. ನಾನು ಡಾಕ್ಯುಮೆಂಟ್ ಅನ್ನು ಸಂಪೂರ್ಣವಾಗಿ ಪರಿಶೀಲಿಸಿದ್ದೇನೆ ಮತ್ತು ನಿಮಗೆ ಅಗತ್ಯವಿರುವ ನಿಖರವಾದ ಮಾಹಿತಿಯನ್ನು ಪತ್ತೆಹಚ್ಚಲು ಅಥವಾ ವಿಷಯವನ್ನು ಸ್ಪಷ್ಟ ಮತ್ತು ಸರಳ ಪದಗಳಲ್ಲಿ ವಿವರಿಸಲು ನಾನು ನಿಮಗೆ ಸಹಾಯ ಮಾಡಬಹುದು. ನಿರ್ದಿಷ್ಟ ವೈಶಿಷ್ಟ್ಯಗಳು, ದೋಷನಿವಾರಣೆ ಹಂತಗಳು ಅಥವಾ ಸಾಮಾನ್ಯ ಬಳಕೆಯ ಕುರಿತು ನೀವು ಮಾರ್ಗದರ್ಶನವನ್ನು ಹುಡುಕುತ್ತಿರಲಿ, ನಿಮ್ಮ ಪ್ರಶ್ನೆಗಳನ್ನು ಕೇಳಲು ಮುಕ್ತವಾಗಿರಿ. ನಿಮ್ಮ ಕಾಳಜಿಗಳು ಅಥವಾ ಅಗತ್ಯಗಳ ಬಗ್ಗೆ ನೀವು ಹೆಚ್ಚು ವಿವರಗಳನ್ನು ಒದಗಿಸಿದರೆ, ನಾನು ಹೆಚ್ಚು ನಿಖರವಾಗಿ ಮತ್ತು ಪರಿಣಾಮಕಾರಿಯಾಗಿ ನಿಮಗೆ ಸಹಾಯ ಮಾಡಬಹುದು!

ಸಹಾಯಕ ಟೈಪ್ ಮಾಡುತ್ತಿದ್ದಾರೆ

ಸಹಾಯಕ ಕೀಬೋರ್ಡ್‌ನಿಂದ ಹೊರಗಿದ್ದಾರೆ. ದಯವಿಟ್ಟು, ನಂತರ ಮತ್ತೆ ಪ್ರಯತ್ನಿಸಿ.

ಬಹು ಭಾಷೆಗಳಲ್ಲಿ ಬರೆಯಲಾದ ಡಾಕ್ಯುಮೆಂಟ್ ಅನ್ನು ನೀವು ತಲುಪಿದಂತೆ ಕಾಣುತ್ತದೆ, ನಿಮ್ಮ ಸ್ಥಳೀಯ ಭಾಷೆಯಲ್ಲದ ಒಂದು ಭಾಷೆಯೂ ಸೇರಿದಂತೆ. ನೀವು ಇಷ್ಟಪಡದ ಭಾಷೆಯಿಲ್ಲದ ಪುಟಗಳನ್ನು ತಾತ್ಕಾಲಿಕವಾಗಿ ಮರೆಮಾಡಲು ನೀವು ಕೆಳಗಿನ ಲಿಂಕ್‌ಗಳನ್ನು ಬಳಸಬಹುದು.