Linksys Small Business WRP400 User guide

Model No: WRP400

USER GUIDE

Wireless-G

Broadband Router with 2 Phone Ports

About Ths Gude

Icon Descriptions

While reading through the User Guide you may see various icons that call attention to specific items. Below is a description of these icons:

NOTE: This check mark indicates that there is a note of interest and is something that you should pay special attention to while using the product.

WARNING: This exclamation point indicates that there is a caution or warning and it is something that could damage your property or product.

WEB: This globe icon indicates a noteworthy website address or e-mail address.

Online Resources

Website addresses in this document are listed without http:// in front of the address because most current web browsers do not require it. If you use an older web browser, you may have to add http:// in front of the web address.

Resource

Linksys

Webste www.linksys.com

Linksys International www.linksys.com/international

Glossary

Network Security www.linksys.com/glossary www.linksys.com/security

Copyright and Trademarks

Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/ or its affiliates in the U.S. and certain other countries. Copyright © 2007

Cisco Systems, Inc. All rights reserved.

Other brands and product names are trademarks or registered trademarks of their respective holders.

Wreless-G Broadband Router wth 2 Phone Ports

About This Guide

Table of Contents

Chapter 1: Product Overview 4

Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Side Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Placement Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Chapter 2: Wireless Security Checklist 7

General Network Security Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Additional Security Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Chapter 3: Advanced Configuration 8

Setup > Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Setup > DDNS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Setup > MAC Address Clone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Setup > Advanced Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Wireless > Basic Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Wireless > Wireless Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Wireless > Wireless MAC Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Wireless > Advanced Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Security > Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Security > VPN Passthrough . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Access Restrictions > Internet Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Applications and Gaming > Single Port Forwarding. . . . . . . . . . . . . . . . . . . . . . . .20

Applications and Gaming > Port Range Forward. . . . . . . . . . . . . . . . . . . . . . . . . .21

Applications & Gaming > Port Range Triggering . . . . . . . . . . . . . . . . . . . . . . . . . .22

Applications and Gaming > DMZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Applications and Gaming > QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Administration > Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Administration > Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Administration > Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Administration > Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Administration > Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Administration > Config Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Status > Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Status > Local Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Status > Wireless Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Access to the Voice Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Voice > Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Voice > System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Voice > User 1/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Voice > Admin Login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33


Table of Contents

Chapter 4: Interactive Voice Response Menu 34

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Menu Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Appendix A: Troubleshooting 35

Appendix B: Specifications 37

Appendix C: Warranty Information 39

Appendix D: Regulatory Information 40

FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

FCC Radiation Exposure Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Safety Notices and Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Industry Canada Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Avis d’Industrie Canada. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Wireless Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Avis de non-responsabilité concernant les appareils sans fil . . . . . . . . . . . . . . . . . .41

Telepermit Statement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Declaration of Conformity with Regard to EU Directive 1999/5/EC (R&TTE Directive) . .42

CE Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

National Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Product Usage Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Technical Documents on www.linksys.com/international . . . . . . . . . . . . . . . . . . . .44

User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste

Electric and Electronic Equipment (WEEE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45


Chapter1

Chapter 1:

Product Overvew

Thank you for choosing the Linksys Wireless-G Broadband

Router with 2 Phone Ports. The Router lets you access the Internet via a wireless connection or through one of its four switched ports. You can also use the Router to share resources such as computers, printers and files. The built-in phone adapter enables Voice-over-IP (VoIP) calls even while you are using the Internet.

Front Panel

Product Overview

Wreless (Green) The Wireless LED lights up when the wireless feature is enabled. It flashes when the Router is actively sending or receiving data over the network.

Ethernet 1- (Green) These numbered LEDs, corresponding with the numbered ports on the

Router’s back panel, serve two purposes. If the

LED is solidly lit, the Router is connected to a device through that port. It flashes to indicate network activity over that port.

Internet (Green) The Internet LED lights up and stays on when there is a connection made through the Internet port. It flashes to indicate network activity over the Internet port.

Back Panel

USB The USB port is reserved for future use.

W-F Protected Setup (White/Orange) If you have client devices, such as wireless adapters, that support Wi-Fi Protected Setup, then you can use Wi-Fi Protected Setup to automatically configure wireless security for your wireless network(s).

To use Wi-Fi Protected Setup, refer to your wireless adapter’s documentation.

The Wi-Fi Protected Setup button lights up white and stays on while wireless security is enabled on your wireless network(s). The button flashes orange if there is an error during the

Wi-Fi Protected Setup process. Make sure the client device supports Wi-Fi Protected Setup, and then try again.

Power (Green/Red) The Power LED lights up green and stays on while the Router is powered on. When the Router goes through its selfdiagnostic mode during every boot-up, the LED will flash. When the diagnostic is complete, it will be solidly lit green. If the LED lights up red, make sure the correct power adapter is used.

If the LED remains red, contact your Internet

Service Provider (ISP) or Internet Telephony

Service Provider (ITSP) for support.

Phone 1-2 (Green) The Phone 1 or 2 LED lights up and stays on when an active line is registered to the corresponding port on the Router’s back panel. The LED slowly flashes when voicemail messages are waiting.


Internet The Internet port is where you will connect your cable or DSL Internet connection.

Phone 1-2 The Phone ports connect standard analog telephones to the Router.

Ethernet 1, 2, 3, These Ethernet ports (1, 2, 3,

4) connect the Router to wired computers and other Ethernet network devices.

Power The Power port is where you will connect the power adapter.

Chapter1

Side Panel


Vertical Placement

The Router has a stand on the panel opposite to the antenna. Rotate the stand 90 degrees, and place the

Router on a level surface near an electrical outlet.

Reset There are two ways to reset the Router’s factory defaults. Either press and hold the Reset button for approximately ten seconds, or restore the defaults from the Administration > Factory

Defaults screen of the Router’s web-based utility. (The Factory Defaults screen allows you to restore the Router and voice defaults separately.)

NOTE: Restoring the voice defaults may require your login (the default user name and password are admn ). If the defaults do not work, contact your

ITSP for more information.

Stand To place the Router in a vertical position, rotate the stand 90 degrees.

Placement Positions

There are three ways to physically install the Router. The first way is to place the Router horizontally on a surface.

The second way is to stand the Router vertically on a surface. The third way is to mount the Router on a wall.

Horizontal Placement

The Router has four rubber feet on its bottom panel. Place the Router on a level surface near an electrical outlet.


Wall-Mounting Placement

The Router has four wall-mount slots on its back panel.

The distance between two adjacent slots is 60 mm

(2.36 inches).

Two screws are needed to mount the Router.

Suggested Mountng Hardware

4-5 mm 1-1.5 mm

† Note: Mounting hardware illustrations are not true to scale.

NOTE: Linksys is not responsible for damages incurred by insecure wall-mounting hardware.

Follow these instructions:

1.

2.

Determine where you want to mount the Router. Make sure that the wall you use is smooth, flat, dry, and sturdy. Also make sure the location is within reach of an electrical outlet.

Drill two holes into the wall. Make sure the holes are

60 mm (2.36 inches) apart.

Chapter1

3.

4.

5.

Insert a screw into each hole and leave 3 mm

(0.12 inches) of its head exposed.

Maneuver the Router so two of the wall-mount slots line up with the two screws.

Place the wall-mount slots over the screws and slide the Router down until the screws fit snugly into the wall-mount slots.

60 mm

Print this page at 100% size. Cut along the dotted line, and place on the wall to drill precise spacing.

Wall Mounting Template



Chapter2

Chapter 2:

Wreless Securty Checklst

Wireless networks are convenient and easy to install, so homes with high-speed Internet access are adopting them at a rapid pace. Because wireless networking operates by sending information over radio waves, it can be more vulnerable to intruders than a traditional wired network.

Like signals from your cellular or cordless phones, signals from your wireless network can also be intercepted. Since you cannot physically prevent someone from connecting to your wireless network, you need to take some additional steps to keep your network secure.

1. Change the default wreless

network name or SSID

Wireless devices have a default wireless network name or Service Set Identifier (SSID) set by the factory. This is the name of your wireless network, and can be up to 32 characters in length. To distinguish your wireless network from other wireless networks that may exist around you, you should change the default wireless network name to something easily recognizable, but do not use personal information (such as your Social Security number) because this information may be available for anyone to see when browsing for wireless networks.

2. Change the default password

For wireless products such as access points and routers, you will be asked for a password when you want to change their settings. These devices have a default password set by the factory. The Linksys default password is admn .

Hackers know these defaults and may try to use them to access your wireless device and change your network settings. To thwart any unauthorized changes, customize the device’s password so it will be hard to guess.

3. Enable MAC address flterng

Linksys routers give you the ability to enable Media Access

Control (MAC) address filtering. The MAC address is a unique series of numbers and letters assigned to every networking device. With MAC address filtering enabled, wireless network access is provided solely for wireless devices with specific MAC addresses. For example, you can specify the MAC address of each computer in your home so that only those computers can access your wireless network.


Wireless Security Checklist

. Enable encrypton

Encryption protects data transmitted over a wireless network. Wi-Fi Protected Access (WPA/WPA2) and Wired

Equivalency Privacy (WEP) offer different levels of security for wireless communication.

A network encrypted with WPA/WPA2 is more secure than a network encrypted with WEP, because WPA/WPA2 uses dynamic key encryption. To protect the information as it passes over the airwaves, you should enable the highest level of encryption supported by your network equipment.

WEP is an older encryption standard and may be the only option available on some older devices that do not support WPA.

•

•

•

General Network Security Guidelines

Wireless network security is useless if the underlying network is not secure.

•

•

•

•

Password protect all computers on the network and individually password protect sensitive files.

Change passwords on a regular basis.

Install anti-virus software and personal firewall software.

Disable file sharing (peer-to-peer). Some applications may open file sharing without your consent and/or knowledge.

Additional Security Tips

Keep wireless routers, access points, or gateways away from exterior walls and windows.

Turn wireless routers, access points, or gateways off when they are not being used (at night, during vacations).

Use strong passphrases that are at least eight characters in length. Combine letters and numbers to avoid using standard words that can be found in the dictionary.

WEB:

For more information on wireless security, visit www.lnksys.com/securty

Chapter3

Chapter 3:

Advanced Confguraton

After setting up the Router with the Setup Wizard (located on the CD-ROM), the Router will be ready for use. However, if you’d like to change its advanced settings, use the

Router’s web-based utility. This chapter describes each web page of the utility and each page’s key functions. You can access the utility via a web browser on a computer connected to the Router.

The web-based utility has these main tabs: Setup, Wireless,

Security, Access Restrictions, Applications & Gaming,

Administration, Status, and Voice. Additional tabs will be available after you click one of the main tabs.

NOTE: When first installing the Router, you should use the Setup Wizard on the Setup CD-

ROM. If you want to configure advanced settings, use this chapter to learn about the web-based utility.

How to Access the Web-Based Utility

To access the web-based utility, launch the web browser on your computer, and enter the Router’s default IP address,

192.1.1.1

, in the Address field. Then press Enter .

NOTE: If you place the Router behind a primary router with the IP address of 192.168.15.1, then the Router will automatically assume a new default IP address, 192.1.1.1

.

A login screen appears. The first time you open the web-based utility, use the default user name and password, admn . (You can set a new password from the

Administration tab’s Management screen.) Click OK to continue.

Login Screen

Setup > Basic Setup

The first screen that appears is the Basic Setup screen. This allows you to change the Router’s general settings.


Advanced Configuration

Setup > Basic Setup

Internet Setup

The Internet Setup section configures the Router to your

Internet connection. Most of this information can be obtained through your Internet Service Provider (ISP).

Internet Connection Type

Select the type of Internet connection your ISP provides from the drop-down menu. These are the available types:

•

•

•

•

•

•

Automatic Configuration - DHCP

Static IP

PPPoE

PPTP

L2TP

Telstra Cable

Automatic Configuration - DHCP

By default, the Router’s Internet Connection Type is set to Automatc Confguraton - DHCP , which should be kept only if your ISP supports DHCP or you are connecting through a dynamic IP address. (This option usually applies to cable connections.)

Internet Connection Type > Automatic Configuration - DHCP

Chapter3

Static IP

If you are required to use a permanent IP address to connect to the Internet, select Statc IP .


Keep Alve: Redal Perod If you select this option, the Router will periodically check your Internet connection. If you are disconnected, then the Router will automatically re-establish your connection. To use this option, select Keep Alve . In the Redial Period field, you specify how often you want the Router to check the Internet connection. The default Redial Period is

30 seconds.

PPTP

Point-to-Point Tunneling Protocol (PPTP) is a service that applies to connections in Europe only.

Default Gateway Your ISP will provide you with the IP address of the ISP server.

DNS 1-3 Your ISP will provide you with at least one DNS

(Domain Name System) server IP address.

PPPoE

Some DSL-based ISPs use PPPoE (Point-to-Point Protocol over Ethernet) to establish Internet connections. If you are connected to the Internet through a DSL line, check with your ISP to see if they use PPPoE. If they do, you will have to enable

Internet Connection Type > Static IP

Internet IP Address This is the Router’s IP address, when seen from the Internet. Your ISP will provide you with the

IP address you need to specify here.

Subnet Mask This is the Router’s Subnet Mask, as seen by users on the Internet (including your ISP). Your ISP will provide you with the Subnet Mask.

PPPoE .

Internet Connection Type > PPPoE

User Name and Password Enter the User Name and

Password provided by your ISP.

Servce Name (Optonal) If provided by your ISP, enter the Service Name.

Connect on Demand: Max Idle Tme You can configure the Router to cut the Internet connection after it has been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. To use this option, select Connect on Demand . In the Max Idle Time field, enter the number of minutes you want to have elapsed before your Internet connection terminates. The default

Max Idle Time is minutes.


Internet Connection Type > PPTP

Internet IP Address This is the Router’s IP address, as seen from the Internet. Enter the IP address provided by your ISP.

Subnet Mask This is the Router’s Subnet Mask, as seen by users on the Internet (including your ISP). Enter the

Subnet Mask provided by your ISP.

Default Gateway Enter the IP address of the ISP server, which is provided by your ISP.





Keep Alve: Redal Perod If you select this option, the

Router will periodically check your Internet connection. If you are disconnected, then the Router will automatically re-establish your connection. To use this option, select

Keep Alve . In the Redial Period field, you specify how often you want the Router to check the Internet connection. The default value is 30 seconds.

9

Chapter3

L2TP

L2TP is a service that applies to connections in Europe and

Israel.

Internet Connection Type > L2TP

Server IP Address This is the IP address of the L2TP

Server. Enter the IP address provided by your ISP.






30 seconds.

Telstra Cable

Telstra Cable is a service used in Australia only.

Internet Connection Type > Telstra Cable

Heart Beat Server This is the IP address of the Heart Beat

Server. Enter the IP address provided by your ISP.



Connect on Demand: Max Idle Tme You can configure the Router to cut the Internet connection after it has been inactive for a specified period of time (Max Idle Time). If


Advanced Configuration your Internet connection has been terminated due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. To use this option, select Connect on Demand . In the Max Idle Time field, enter the number of minutes you want to have elapsed before your Internet connection terminates. The default



30 seconds.

Optional Settings

Some of these settings may be required by your ISP. Verify with your ISP before making any changes.

Optional Settings

Host Name and Doman Name These fields allow you to supply a host and domain name for the Router. Some ISPs, usually cable ISPs, require these names as identification.

You may have to check with your ISP to see if your broadband Internet service has been configured with a host and domain name. In most cases, leaving these fields blank will work.

MTU MTU is the Maximum Transmission Unit. It specifies the largest packet size permitted for Internet transmission.

Select Manual if you want to manually enter the largest packet size that is transmitted. To have the Router select the best MTU for your Internet connection, keep the default setting, Auto .

Sze When Manual is selected in the MTU field, this option is enabled. Leave this value in the 576 to 1500 range. The default size depends on the Internet Connection Type:

•

•

•

•

DHCP or Static IP: 100

PPPoE: 192

PPTP or L2TP: 10

Telstra Cable: 100

Network Setup

The Network Setup section changes the settings on the network connected to the Router’s Ethernet ports. Wireless setup is performed through the Wireless tab.

10

Chapter3

Router IP

This presents both the Router’s Local IP Address and

Subnet Mask as seen by your network.

Router IP

DHCP Server Setting

The settings allow you to configure the Router’s Dynamic

Host Configuration Protocol (DHCP) server function. The

Router can be used as a DHCP server for your network. A

DHCP server automatically assigns an IP address to each computer on your network. If you choose to enable the

Router’s DHCP server option, make sure there is no other

DHCP server on your network.

DHCP Server Setting

DHCP Server DHCP is enabled by factory default. If you already have a DHCP server on your network, or you don’t want a DHCP server, then select Dsabled (no other DHCP features will be available).

DHCP Reservaton Click this button if you want to assign a fixed local IP address to a MAC address.

DHCP Reservation

You will see a list of DHCP clients with the following information: Client Name, Interface, IP Address, and

MAC Address.

DHCP Reservation



•

•

Select Clents from DHCP Table Click the Select check box to reserve a client’s IP address. Then click

Add Clents .

Manually Addng Clent To manually assign an IP address, enter the client’s name in the Enter Client

Name field. Enter the IP address you want it to have in the Assign IP Address field. Enter its MAC address in the

To This MAC Address field. Then click Add .

Clients Already Reserved

A list of DHCP clients and their fixed local IP addresses will be displayed at the bottom of the screen. If you want to remove a client from this list, click Remove .

Click Save Settngs to apply your changes, or click

Cancel Changes to cancel your changes. To view the most up-to-date information, click Refresh . To exit this screen, click Close .

Startng IP Address Enter a value for the DHCP server to start with when issuing IP addresses. Because the

Router’s default IP address is 192.168.15.1, the Starting

IP Address must be 192.168.15.2 or greater, but smaller than 192.168.15.253. The default Starting IP Address is

192.1.1.100

.

Maxmum DHCP Users Enter the maximum number of computers that you want the DHCP server to assign IP addresses to. This number cannot be greater than 253.

The default is 0 .

IP Address Range Displayed here is the range of available

IP addresses.

Clent Lease Tme The Client Lease Time is the amount of time a network user will be allowed connection to the

Router with their current dynamic IP address. Enter the amount of time, in minutes, that the user will be “leased” this dynamic IP address. After the time is up, the user will be automatically assigned a new dynamic IP address. The default is 0 minutes, which means one day.

Statc DNS 1-3 The Domain Name System (DNS) is how the

Internet translates domain or website names into Internet addresses or URLs. Enter at least one DNS server IP address, which is provided by your ISP. If you wish to use another, enter that IP address in one of these fields. You can enter up to three DNS server IP addresses here. The Router will use these for quicker access to functioning DNS servers.

WINS The Windows Internet Naming Service (WINS) manages each PC’s interaction with the Internet. If you use a WINS server, enter that server’s IP address here.

Otherwise, leave this blank.

Time Setting

Tme Zone Select the time zone in which your network functions from this drop-down menu.

11

Chapter3

Automatcally adjust clock for daylght savng changes Select this option if you want the Router to automatically adjust for daylight saving time. This option is enabled by default.

Tme Server Address If you want to use the Router’s default Network Time Protocol (NTP) server, keep the default, Auto . If you want to specify the NTP server, select

Manual , and enter the URL or IP address of the NTP server you want to use.

Resync Tmer The timer controls how often the Router resyncs with the NTP server. Enter the number of seconds you want the interval to be, or keep the default, 300 seconds.

DynDNS.org

Time Setting

Click Save Settngs to apply your changes, or click Cancel

Changes to cancel your changes.

Setup > DDNS

The Router offers a Dynamic Domain Name System (DDNS) feature. DDNS lets you assign a fixed host and domain name to a dynamic Internet IP address. It is useful when you are hosting your own website, FTP server, or other server behind the Router.

Before you can use this feature, you need to sign up for DDNS service with a DDNS service provider, www.dyndns.org or www.TZO.com. If you do not want to use this feature, keep the default setting, Dsabled .

DDNS

DDNS Service

If your DDNS service is provided by DynDNS.org, then select DynDNS.org

from the drop-down menu. If your

DDNS service is provided by TZO, then select TZO.com

.

The features available on the DDNS screen will vary, depending on which DDNS service provider you use.


Setup > DDNS > DynDNS

User Name Enter the User Name for your DDNS account.

Password Enter the Password for your DDNS account.

Host Name The is the DDNS URL assigned by the DDNS service.

System Select the DynDNS service you use: Dynamc ,

Statc , or Custom . The default selection is Dynamc .

Mal Exchange (Optonal) Enter the address of your mail exchange server, so e-mails to your DynDNS address go to your mail server.

Backup MX This feature allows the mail exchange server to be a backup. To disable this feature, keep the default,

Dsabled . To enable the feature, select Enabled . If you are not sure which setting to select, keep the default,

Dsabled .

Wldcard This setting enables or disables wildcards for your host. For example, if your DDNS address is myplace.dyndns.org

and you enable wildcards, then x.myplace.dyndns.org

will work as well (x is the wildcard).

To disable wildcards, keep the default, Dsabled . To enable wildcards, select Enabled . If you are not sure which setting to select, keep the default, Dsabled .

Internet IP Address The Router’s Internet IP address is displayed here. Because it is dynamic, it will change.

Status The status of the DDNS service connection is displayed here.

Update To manually trigger an update, click this button.



Wreless-G Broadband Router wth 2 Phone Ports 12

Chapter3

TZO.com


Clone Your PC’s MAC Click this button to clone the MAC address of the computer you are using.



Setup > Advanced Routing

This screen is used to set up the Router’s advanced functions. Operating Mode allows you to select the type(s) of advanced functions you use. Dynamic Routing automatically adjusts how packets travel on your network.

Static Routing sets up a fixed route to another network destination.

Setup > DDNS > TZO

E-mal Address, TZO Key, and Doman Name Enter the settings of the account you set up with TZO.

Internet IP Address The Router’s Internet IP address is displayed here. Because it is dynamic, it will change.

Status The status of the DDNS service connection is displayed here.

Update To manually trigger an update, click this button.



Setup > MAC Address Clone

A MAC address is a 12-digit code assigned to a unique piece of hardware for identification. Some ISPs will require you to register a MAC address in order to access the

Internet. If you do not wish to re-register the MAC address with your ISP, you may assign the MAC address you have currently registered with your ISP to the Router with the

MAC Address Clone feature.

Setup > MAC Address Clone

MAC Address Clone

Enabled/Dsabled To have the MAC address cloned, select Enabled .

MAC Address Enter the MAC address registered with your ISP here.


Setup > Advanced Routing

Advanced Routing

NAT

Enabled/Dsabled If this Router is hosting your network’s connection to the Internet, keep the default, Enabled . If another router exists on your network, select Dsabled .

When the NAT setting is disabled, dynamic routing will be enabled.

Dynamic Routing (RIP)

Enabled/Dsabled This feature enables the Router to automatically adjust to physical changes in the network’s layout and exchange routing tables with the other router(s). The Router determines the network packets’ route based on the fewest number of hops between the source and the destination. When the NAT setting is enabled, the Dynamic Routing feature is automatically disabled. When the NAT setting is disabled, this feature is available. Select Enabled to use the Dynamic Routing feature.

Static Routing

A static route is a pre-determined pathway that network information must travel to reach a specific host or network.

13

Chapter3

Enter the information described below to set up a new static route.

Route Entres To set up a static route between the Router and another network, select a number from the dropdown list. Click Delete Ths Entry to delete a static route.

Enter Route Name Enter a name for the Route here, using a maximum of 25 alphanumeric characters.

Destnaton LAN IP The Destination LAN IP is the address of the remote network or host to which you want to assign a static route.

Subnet Mask The Subnet Mask determines which portion of a Destination LAN IP address is the network portion, and which portion is the host portion.

Gateway This is the IP address of the gateway device that allows for contact between the Router and the remote network or host.

Interface This interface tells you whether the Destination

LAN IP address is on the LAN and Wreless (Ethernet and wireless networks) or the Internet (WAN) .

Click Show Routng Table to view the static routes you have already set up.

Advanced Routing > Routing Table

Routing Table

For each route, the Destination LAN IP address, Subnet

Mask, Gateway, and Interface are displayed. Click

Refresh to update the information. Click Close to exit this screen.




Wireless > Basic Wireless Settings

The basic settings for wireless networking are set on this screen.

Wireless > Basic Wireless Settings

There are two ways to configure the Router’s wireless network(s), manual and Wi-Fi Protected Setup. To manually configure the wireless settings, use the Basic Wireless

Settings screen.

If you have client devices, such as wireless adapters, that support Wi-Fi Protected Setup, then you can use Wi-Fi

Protected Setup to automatically configure wireless security for your wireless network(s). To use Wi-Fi Protected

Setup, refer to your wireless adapter’s documentation.

NOTE: If you have client devices that do not support Wi-Fi Protected Setup, click the Wreless

Securty tab. Note the security settings, and then manually enter them on those devices.

Wireless Network

Network Mode From this drop-down menu, you can select the wireless standards running on your network(s).

If you have Wireless-G and Wireless-B devices in your network(s), keep the default setting, Mxed . If you have only Wireless-G devices, select Wreless-G only . If you have only Wireless-B devices, select Wreless-B only .

Wreless Channel Select the channel you want to use.

To allow the Router to select the best available wireless channel, keep the default, Auto .

SSID1/2 The SSID is the network name shared among all devices in a wireless network. The Router can support up to two wireless networks. By default, one wireless network is enabled, and you can create a second wireless network.


Chapter3

Configure the following settings for each wireless network:

• Wreless Network Name (SSID) The default wireless network uses this name: “linksys” followed by the last four digits of the Router’s wireless MAC address. To rename the default wireless network, enter a unique Wireless Network Name, which is case-sensitive and must not exceed 32 characters

(use any of the characters on the keyboard).

To create a second wireless network, enter a unique

Wireless Network Name in the SSID2 setting. (To activate this network, select Network Enabled .)

NOTE: Your ISP or ITSP may control the SSID2 settings. Contact your ISP or ITSP for more information.

• SSID Broadcast Enabled When wireless clients survey the local area for wireless networks to associate with, they detect the SSID broadcast by the Router. If you want to broadcast the SSID, keep the check box selected. If you do not want to broadcast the SSID, deselect the check box.

• Network Enabled To enable the wireless network, select the check box. To disable the wireless network, deselect the check box.



Wireless > Wireless Security

The Wireless Security screen configures the security of your wireless network(s). The Router supports the following wireless security mode options: WPA Personal,

WPA Enterprise, WPA2 Personal, WPA2 Enterprise, and

WEP. (WPA stands for Wi-Fi Protected Access, which is a security standard stronger than WEP encryption. WEP stands for Wired Equivalent Privacy.) These options are briefly discussed here. For detailed instructions on configuring wireless security for the Router, refer to

“Chapter 2: Wireless Security.”

NOTE: If you used Wi-Fi Protected Setup to configure your wireless network(s), then wireless security has already been set up. Do not make changes to the Wireless Security screen.

Wireless Security

Select a SSID Select the appropriate SSID. (If you enabled the second wireless network on the Basic Wireless Settings screen, then set up wireless security for each SSID.)



Security Mode

Select the security method for your wireless network.

Proceed to the appropriate instructions. If you do not want to use wireless security, keep the default, Dsabled .

WPA Personal

NOTE: If you are using WPA, always remember that each device in your wireless network MUST use the same WPA method and shared key, or else the network will not function properly.

Security Mode > WPA Personal

WPA Algorthms WPA supports two encryption methods,

TKIP and AES, with dynamic encryption keys. Select the type of algorithm, TKIP or AES . The default is TKIP .

WPA Shared Key Enter a WPA Shared Key of 8-63 characters.

Group Key Renewal Enter a Group Key Renewal period, which instructs the Router how often it should change the encryption keys. The default is 300 seconds.

WPA2 Personal

Security Mode > WPA2 Personal

WPA Algorthms WPA2 supports two encryption methods, TKIP and AES, with dynamic encryption keys.

Select the type of algorithm, AES or TKIP + AES . The default is TKIP + AES .

WPA Shared Key Enter a WPA Shared Key of 8-63 characters.

1

Chapter3

Group Key Renewal Enter a Group Key Renewal period, which instructs the Router how often it should change the encryption keys. The default is 300 seconds.

WPA Enterprise

This option features WPA used in coordination with a

RADIUS server. (RADIUS stands for Remote Authentication

Dial-In User Service. This option should only be used when a RADIUS server is connected to the Router.)


Security Mode > WPA Enterprise

WPA Algorthms WPA supports two encryption methods,

TKIP and AES, with dynamic encryption keys. Select the type of algorithm, TKIP or AES . The default is TKIP .

RADIUS Server Address Enter the IP address of the

RADIUS server.

RADIUS Port Enter the port number of the RADIUS server. The default value is 112 .

Shared Key Enter the key shared between the Router and the server.

Key Renewal Tmeout Enter a Key Renewal Timeout period, which instructs the Router how often it should change the encryption keys. The default is 300 seconds.

WPA2 Enterprise

This option features WPA2 used in coordination with a

RADIUS server. (It should only be used when a RADIUS server is connected to the Router.)

Security Mode > WPA2 Enterprise

WPA Algorthms WPA2 supports two encryption methods, TKIP and AES, with dynamic encryption keys.

Select the type of algorithm, AES or TKIP + AES . The default is TKIP + AES .

RADIUS Server Address Enter the IP address of the

RADIUS server.

RADIUS Port Enter the port number of the RADIUS server. The default value is 112 .

Shared Key Enter the key shared between the Router and the server.

Key Renewal Tmeout Enter a Key Renewal Timeout period, which instructs the Router how often it should change the encryption keys. The default is 300 seconds.

WEP

WEP is a basic encryption method, which is not as secure as WPA.


Security Mode > WEP

Encrypton Select a level of WEP encryption, bts 10 hex dgts or 12 bts 2 hex dgts . The default is bts

10 hex dgts .

Passphrase Enter a Passphrase to automatically generate

WEP keys. Then click Generate .

1

Chapter3

Key 1- If you did not enter a Passphrase, enter the WEP key(s) manually.

TX Key Select which TX (Transmit) Key to use. The default is 1 .



Wireless > Wireless MAC Filter

Wireless access can be filtered by using the MAC addresses of the wireless devices transmitting within your network’s radius.


MAC Address Filter List

Wreless Clent Lst Click this to open the Wireless Client

List screen.

Wireless > Wireless MAC Filter

Wireless MAC Filter

Select a SSID Select the appropriate SSID. (If you enabled the second wireless network on the Basic Wireless Settings screen, then set up wireless MAC filtering for each SSID.)

Wreless MAC Flter To filter wireless users by MAC address, either permitting or blocking access, select Enabled . If you do not wish to filter users by MAC address, keep the default setting, Dsabled .

Access Restriction

Prevent Select this to block wireless access by MAC address. This button is selected by default.

Permt Select this to allow wireless access by MAC address. This button is not selected by default.


Wireless Client List

Wireless Client List

This screen shows the online and offline devices of the wireless network(s). The device information includes

Client Name, IP Address, MAC Address, and Status.

Select Save to MAC Address Flter Lst for any device you want to add to the MAC Address Filter List. Then click Add .

To retrieve the most up-to-date information, click

Refresh . To exit this screen and return to the Wireless

MAC Filter screen, click Close .

MAC 01-0 Enter the MAC addresses of the devices whose wireless access you want to block or allow.



Wireless > Advanced Wireless Settings

The Advanced Wireless Settings screen is used to set up the Router’s advanced wireless functions. These settings should only be adjusted by an expert administrator as incorrect settings can reduce wireless performance.

Wireless > Advanced Wireless Settings

1

Chapter3

Advanced Wireless

Authentcaton Type The default is set to Auto , which allows either Open System or Shared Key authentication to be used. With Open System authentication, the sender and the recipient do NOT use a WEP key for authentication.

With Shared Key authentication, the sender and recipient use a WEP key for authentication. Select Shared Key to only use Shared Key authentication.

Transmsson Rate The rate of data transmission should be set depending on the speed of your wireless network(s).

You can select from a range of transmission speeds, or you can select Auto to have the Router automatically use the fastest possible data rate and enable the Auto-Fallback feature. Auto-Fallback will negotiate the best possible connection speed between the Router and a wireless client. The default is Auto .

CTS Protecton Mode The Router will automatically use CTS (Clear-To-Send) Protection Mode when your

Wireless-G products are experiencing severe problems and are not able to transmit to the Router in an environment with heavy 802.11b traffic. This function boosts the

Router’s ability to catch all Wireless-G transmissions but will severely decrease performance. The default is Auto .

Beacon Interval Enter a value between 1 and 65,535 milliseconds. The Beacon Interval value indicates the frequency interval of the beacon. A beacon is a packet broadcast by the Router to synchronize the wireless network(s). The default value is 100 .

DTIM Interval This value, between 1 and 255, indicates the interval of the Delivery Traffic Indication Message

(DTIM). A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages. When the Router has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. Its clients hear the beacons and awaken to receive the broadcast and multicast messages. The default value is 1 .

RTS Threshold Should you encounter inconsistent data flow, only minor reduction of the default value, 23 , is recommended. If a network packet is smaller than the preset RTS threshold size, the RTS/CTS mechanism will not be enabled. The Router sends Request to Send (RTS) frames to a particular receiving station and negotiates the sending of a data frame. After receiving an RTS, the wireless station responds with a Clear to Send (CTS) frame to acknowledge the right to begin transmission. The RTS

Threshold value should remain at its default value of

23 .





Security > Firewall

The Firewall screen is used to configure a firewall that can filter out various types of unwanted traffic on the Router’s local network.

Security > Firewall

Firewall

SPI Frewall Protecton To use firewall protection, keep the default, Enabled . To turn off firewall protection, select

Dsabled .

Internet Filter

Flter Anonymous Internet Requests This feature makes it more difficult for outside users to work their way into your network. This feature is selected by default.

Deselect the feature to allow anonymous Internet requests.

Flter Internet NAT Redrecton This feature uses port forwarding to block access to local servers from local networked computers. Select this feature to filter Internet

NAT redirection. It is not selected by default.

Flter IDENT (Port 113) This feature keeps port 113 from being scanned by devices outside of your local network.

This feature is selected by default. Deselect this feature to disable it.

Web Filter

Proxy Use of WAN proxy servers may compromise the

Router’s security. Denying Proxy will disable access to any

WAN proxy servers. Select this feature to enable proxy filtering. Deselect the feature to allow proxy access.

Java Java is a programming language for websites. If you deny Java, you run the risk of not having access to Internet sites created using this programming language. Select this feature to enable Java filtering. Deselect the feature to allow Java usage.

1

Chapter3

ActveX ActiveX is a programming language for websites.

If you deny ActiveX, you run the risk of not having access to

Internet sites created using this programming language.

Select this feature to enable ActiveX filtering. Deselect the feature to allow ActiveX usage.

Cookes A cookie is data stored on your computer and used by Internet sites when you interact with them. Select this feature to filter cookies. Deselect the feature to allow cookie usage.



Security > VPN Passthrough

The VPN Passthrough screen allows you to enable VPN tunnels using IPSec, PPTP, or L2TP protocols to pass through the Router’s firewall.


Security > VPN Passthrough

VPN Passthrough

IPSec Passthrough Internet Protocol Security (IPSec) is a suite of protocols used to implement secure exchange of packets at the IP layer. To allow IPSec tunnels to pass through the Router, keep the default, Enabled .

PPTP Passthrough Point-to-Point Tunneling Protocol

(PPTP) allows the Point-to-Point Protocol (PPP) to be tunneled through an IP network. To allow PPTP tunnels to pass through the Router, keep the default, Enabled .

L2TP Passthrough Layer 2 Tunneling Protocol is the method used to enable Point-to-Point sessions via the

Internet on the Layer 2 level. To allow L2TP tunnels to pass through the Router, keep the default, Enabled .



Access Restrictions > Internet Access

The Internet Access screen allows you to block or allow specific kinds of Internet usage and traffic, such as Internet access, designated services, and websites during specific days and times.

Access Restrictions > Internet Access

Internet Access Policy

Access Polcy Access can be managed by a policy. Use the settings on this screen to establish an access policy (after

Save Settngs is clicked). Selecting a policy from the dropdown menu will display that policy’s settings. To delete a policy, select that policy’s number and click Delete Ths

Polcy . To view all the policies, click Summary .

Summary

The policies are listed with the following information:

No., Policy Name, Access, Days, Time of Day, and status

(Enabled). To enable a policy, select Enabled . To delete a policy, click Delete . Click Save Settngs to save your changes, or click Cancel Changes to cancel your changes.

To return to the Internet Access Policy screen, click Close .


Chapter3

Summary

Status Policies are disabled by default. To enable a policy, select the policy number from the drop-down menu, and select Enabled .

2.

3.

4.

To create a policy, follow steps 1-11. Repeat these steps to create additional policies, one at a time.

1.

Select a number from the Access Policy drop-down menu.

Enter a Policy Name in the field provided.

To enable this policy, select Enabled .

Click Edt Lst to select which computers will be affected by the policy. The List of PCs screen appears.

You can select a PC by MAC address or IP address. You can also enter a range of IP addresses if you want this policy to affect a group of computers. After making your changes, click Save Settngs to apply your changes, or click Cancel Changes to cancel your changes. Then click Close .


6.

7.

Decide which days and what times you want this policy to be enforced. Select the individual days during which the policy will be in effect, or select Everyday . Then enter a range of hours and minutes during which the policy will be in effect, or select 2 Hours .

You can block websites with specific URL addresses.

Enter each URL in a separate URL field.

8.

9.

You can also block websites using specific keywords.

Enter each keyword in a separate Keyword field.

You can filter access to various services accessed over the Internet, such as FTP or telnet. (You can block up to three applications per policy.)

From the Applications list, select the application you want to block. Then click the >> button to move it to the Blocked List. To remove an application from the

Blocked List, select it and click the << button.

10.

If the application you want to block is not listed or you want to edit a service’s settings, enter the application’s name in the Application Name field. Enter its range in the Port Range fields. Select its protocol from the Protocol drop-down menu. Then click Add .

To modify a service, select it from the

Application list. Change its name, port range, and/or protocol setting. Then click Modfy .

To delete a service, select it from the Application list.

Then click Delete .

11.

Click Save Settngs to save the policy’s settings. To cancel the policy’s settings, click Cancel Changes .

Applications and Gaming > Single Port

Forwarding

The Single Port Forwarding screen allows you to customize port services for common applications on this screen.

When users send these types of requests to your network via the Internet, the Router will forward those requests to the appropriate servers (computers). Before using forwarding, you should assign static IP addresses to the designated servers (use the DHCP Reservation feature on the Basic Setup screen).

List of PCs

5.

Select the appropriate option, Deny or Allow , depending on whether you want to block or allow

Internet access for the computers you listed on the List of PCs screen.


Chapter3

Advanced Configuration that use Internet access to perform functions such as videoconferencing or online gaming. Some Internet applications may not require any forwarding.)

When users send these types of requests to your network via the Internet, the Router will forward those requests to the appropriate servers (computers). Before using forwarding, you should assign static IP addresses to the designated servers (use the DHCP Reservation feature on the Basic Setup screen).

If you need to forward all ports to one computer, click the

DMZ tab.

Applications and Gaming > Single Port Forwarding

Single Port Forwarding

Common applications are available for the first five entries. Select the appropriate application. Then enter the

IP address of the server that should receive these requests.

Select Enabled to activate this entry.

For additional applications, complete the following fields:

Applcaton Name Enter the name you wish to give the application. Each name can be up to 12 characters.

External Port Enter the external port number used by the server or Internet application. Check with the Internet application documentation for more information.

Internal Port Enter the internal port number used by the server or Internet application. Check with the Internet application documentation for more information.

Protocol Select the protocol used for this application, either TCP , UDP , or Both .

To IP Address For each application, enter the IP address of the PC that should receive the requests. If you assigned a static IP address to the PC, then you can click DHCP

Reservaton on the Basic Setup screen to look up its static

IP address.

Enabled For each application, select Enabled to enable port forwarding.



Applications and Gaming > Port Range

Forward

The Port Range Forward screen allows you to set up public services on your network, such as web servers, ftp servers, e-mail servers, or other specialized Internet applications.

(Specialized Internet applications are any applications


Applications and Gaming > Port Range Forward

Port Range Forward

To forward a port, enter the information on each line for the criteria required.

Applcaton Name In this field, enter the name you wish to give the application. Each name can be up to 12 characters.

Start~End Port Enter the number or range of port(s) used by the server or Internet applications. Check with the Internet application documentation for more information.

Protocol Select the protocol used for this application, either TCP , UDP , or Both .

To IP Address For each application, enter the IP address of the PC running the specific application. If you assigned a static IP address to the PC, then you can click DHCP

Reservaton on the Basic Setup screen to look up its static

IP address.

Enabled Select Enabled to enable port forwarding for the applications you have defined.



21

Chapter3

Applications & Gaming > Port Range

Triggering

The Port Range Triggering screen allows the Router to watch outgoing data for specific port numbers. The IP address of the computer that sends the matching data is remembered by the Router, so that when the requested data returns through the Router, the data is pulled back to the proper computer by way of IP address and port mapping rules.


Applications and Gaming > Port Range Triggering

Port Range Triggering

Applcaton Name Enter the application name of the trigger.

Trggered Range For each application, enter the starting and ending port numbers of the triggered port number range. Check with the Internet application documentation for the port number(s) needed.

Forwarded Range For each application, enter the starting and ending port numbers of the forwarded port number range. Check with the Internet application documentation for the port number(s) needed.

Enabled Select Enabled to enable port triggering for the applications you have defined.



Applications and Gaming > DMZ

The DMZ feature allows one network computer to be exposed to the Internet for use of a special-purpose service such as Internet gaming or videoconferencing.

DMZ hosting forwards all the ports at the same time to one PC. The Port Range Forwarding feature is more secure because it only opens the ports you want to have opened, while DMZ hosting opens all the ports of one computer, exposing the computer to the Internet.


Applications and Gaming > DMZ

DMZ

Any PC whose port is being forwarded must have its DHCP client function disabled and should have a new static IP address assigned to it because its IP address may change when using the DHCP function.

Enabled/Dsabled To disable DMZ hosting, select

Dsabled . To expose one PC, select Enabled . Then configure the following settings:

Source IP Address If you want any IP address to be the source, select Any IP Address . If you want to specify an IP address or range of IP addresses as the designated source, select and complete the IP address range fields.

Destnaton If you want to specify the DMZ host by IP address, select IP Address and enter the IP address in the field provided. If you want to specify the DMZ host by MAC address, select MAC Address and enter the MAC address in the field provided. To retrieve this information, click DHCP Clent Table .

DMZ > DHCP Client Table

DHCP Client Table

The DHCP Client Table lists computers and other devices that have been assigned IP addresses by the Router. The list can be sorted by Client Name, IP

Address, and MAC Address. To select a DHCP client, click

Select . To retrieve the most up-to-date information, click Refresh . To exit this screen and return to the DMZ screen, click Close .

22

Chapter3



Applications and Gaming > QoS

Quality of Service (QoS) ensures better service to high-priority types of network traffic, which may involve demanding, real-time applications, such as videoconferencing.

Advanced Configuration select Manual , and enter the appropriate number in the field provided.

Category

There are four categories available. Select one of the following: Applcaton , Onlne Games , MAC Address , or Ethernet Port . Proceed to the instructions for your selection.

Application

Applcatons Select the appropriate application. If you select Add a New Application, follow the Add a New

Application instructions.

Prorty Select the appropriate priority: Hgh , Medum ,

Normal , or Low .

Click Add to save your changes. Your new entry will appear in the Summary list.

Add a New Application

Applications and Gaming > QoS

QoS (Quality of Service)

Wireless

WMM Support If you have other devices that support

Wi-Fi Multimedia (WMM) on your network, select Enabled .

Otherwise, keep the default, Dsabled .

No Acknowledgement If you want to disable the Router’s

Acknowledgement feature, so the Router will not re-send data if an error occurs, then select Enabled . Otherwise, keep the default, Dsabled .

Internet Access Priority

In this section, you can set the bandwidth priority for a variety of applications and devices. There are four levels priority: High, Medium, Normal, or Low. When you set priority, do not set all applications to High, because this will defeat the purpose of allocating the available bandwidth.

If you want to select below normal bandwidth, select Low.

Depending on the application, a few attempts may be needed to set the appropriate bandwidth priority.

Enabled/Dsabled To use the QoS policies you have set, keep the default, Enabled . Otherwise, select Dsabled .

Upstream Bandwdth To allow the Router to control the maximum bandwidth for upstream data transmissions, keep the default, Auto . To manually set the maximum,


QoS > Add a New Application

Enter a Name Enter any name to indicate the name of the entry.

Port Range Enter the port range that the application will be using. For example, if you want to allocate bandwidth for FTP, you can enter 21-21. If you need services for an application that uses from 1000 to 1250, you enter 1000-

1250 as your settings. You can have up to three ranges to define for this bandwidth allocation. Port numbers can range from 1 to 65535. Check your application’s documentation for details on the service ports used.

Select the protocol TCP , UDP , or Both .

Prorty Select the appropriate priority: Hgh , Medum

(Recommend) , Normal , or Low .


Online Games

QoS > Online Games

23

Chapter3

Game Select the appropriate game. If you select Add a

New Game, follow the Add a New Game instructions.




Add a New Game

Ethernet Port

QoS > Add a New Game

Enter a Name Enter any name to indicate the name of the entry.

Port Range Enter the port range that the application will be using. For example, if you want to allocate bandwidth for FTP, you can enter 21-21. If you need services for an application that uses from 1000 to 1250, you enter 1000-

1250 as your settings. You can have up to three ranges to define for this bandwidth allocation. Port numbers can range from 1 to 65535. Check your application’s documentation for details on the service ports used.

Select the protocol TCP , UDP , or Both .




MAC Address


QoS > Ethernet Port

Ethernet Select the appropriate Ethernet port.




Summary

This lists the QoS entries you have created for your applications and devices.

Prorty This column displays the bandwidth priority of

High, Medium, Normal, or Low.

Name This column displays the application, device, or port name.

Informaton This column displays the port range or

MAC address entered for your entry. If a pre-configured application or game was selected, there will be no valid entry shown in this section.

Remove Click this button to remove an entry.

Edt Click this button to make changes.



Administration > Management

The Administration > Management screen allows the network’s administrator to manage specific Router functions for access and security.

QoS > MAC Address

Enter a Name Enter a name for your device.

MAC Address Enter the MAC address of your device.





Chapter3

Administration > Management

Management

Router Access

To ensure the Router’s security, you will be asked for your password when you access the Router’s web-based utility.

The default is admn .

Router Password Enter a new password for the Router.

Re-enter to confrm Enter the password again to confirm.

Web Access

Web Utlty Access HTTP (HyperText Transport Protocol) is the communications protocol used to connect to servers on the World Wide Web. HTTPS uses SSL (Secured Socket

Layer) to encrypt data transmitted for higher security.

Select HTTP or HTTPS . HTTP is the default.

Web Utlty Access va Wreless If you are using the

Router in a public domain where you are giving wireless access to your guests, you can disable wireless access to the Router’s web-based utility. You will only be able to access the utility via a wired connection if you disable the setting. Keep the default, Enabled , to allow wireless access to the utility, or select Dsabled to block wireless access to the utility.

Remote Access

Remote Management To permit remote access of the

Router, from outside the local network, select Enabled .




Web Utlty Access HTTP (HyperText Transport Protocol) is the communications protocol used to connect to servers on the World Wide Web. HTTPS uses SSL (Secured Socket

Layer) to encrypt data transmitted for higher security.

Select HTTP or HTTPS . HTTP is the default.

Remote Upgrade If you want to be able to upgrade the

Router remotely, from outside the local network, select

Enabled . (You must have the Remote Management feature enabled as well.) Otherwise, keep the default,

Dsabled .

Allowed Remote IP Address If you want to be able to access the Router from any external IP address, select Any

IP Address . If you want to specify an external IP address or range of IP addresses, then select the second option and complete the fields provided.

Remote Management Port Enter the port number that will be open to outside access.

NOTE: When you are in a remote location and wish to manage the Router, enter http://<Internet_IP_address>:port or https://<Internet_IP_address>:por t , depending on whether you use HTTP or HTTPS.

Enter the Router’s specific Internet IP address in place of <Internet_IP_address>, and enter the

Remote Management Port number in place of the word port.

UPnP

Universal Plug and Play (UPnP) allows Windows XP and Vista to automatically configure the Router for various Internet applications, such as gaming and videoconferencing.

UPnP If you want to use UPnP, keep the default, Enabled .

Otherwise, select Dsabled .

Allow Users to Confgure Keep the default, Enabled , if you want to be able to make manual changes to the

Router while using the UPnP feature. Otherwise, select

Dsabled .

Keep UPnP Confguratons After System Reboot If you enable the Allow Users to Configure option, then this option will be available. Select Enabled , if you want to keep UPnP configuration settings after the Router reboots.


Allow Users to Dsable Internet Access Select Enabled , if you want to be able to prohibit any and all Internet connections. Otherwise, keep the default, Dsabled .

Multimedia Streaming

RTSP Support If you are experience issues with videoon-demand applications, select Enabled to improve multimedia transmissions. Using this option, the Router will establish channels with the Real Time Streaming

2

Chapter3

Protocol) RTSP server, which is located at the ISP. Otherwise, keep the default, Dsabled .

IGMP

Internet Group Multicast Protocol (IGMP) is used to establish membership in a multicast group and is commonly used for multicast streaming applications. For example, you may have Internet Protocol Television (IPTV) with multiple setup boxes on the same local network.

These setup boxes have different video streams running simultaneously, so you should use the IGMP feature of the

Router.

Support IGMP Verson Select the version you want to support, IGMP v1 , IGMP v2 , or IGMP v3 . If you are not sure which version to select, keep the default, IGMP v2 .

IGMP Proxy Keep the default, Enabled , if you want to allow multicast traffic through the Router for your multimedia application devices. Otherwise, select

Dsabled .

Immedate Leave Select Enabled , if you use IPTV applications and want to allow immediate channel swapping or flipping without lag or delays. Otherwise, keep the default, Dsabled .



Administration > Log

The Router can keep logs of all traffic for your Internet connection.


Log > View Log

Log

•

•

Type Select Incomng Log , Outgong Log , Securty

Log , or DHCP Clent Log .

<Type> Log The Incoming Log will display a temporary log of the source IP addresses and destination port numbers for the incoming Internet traffic. The

Outgoing Log will display a temporary log of the local IP addresses, destination URLs/IP addresses, and service/port numbers for the outgoing Internet traffic.

The Security log will display the login information for the web-based utility. The DHCP Client Log will display the LAN DHCP server status information.

Click Refresh to update the log. Click Clear to clear all the information that is displayed.



Administration > Diagnostics

The diagnostic tests (Ping and Traceroute) allow you to check the connections of your network devices, including connection to the Internet.

Administration > Log

Log

Log To disable the Log function, keep the default,

Dsabled . To monitor traffic between the network and the

Internet, select Enabled . With logging enabled, you can choose to view temporary logs.

Vew Log To view the logs, click Vew Log .

Administration > Diagnostics


Chapter3

Diagnostics

Ping Test

The Ping test checks the status of a connection.

IP or URL Address Enter the address of the PC whose connection you wish to test.

Packet Sze Enter the packet size you want to use. The default is 32 bytes.

Tmes to Png Enter many times you wish to test it.

Start to Png To run the test, click this button. The Ping

Test screen will show if the test was successful. Click Close to return to the Diagnostics screen.


Diagnostics > Traceroute

Administration > Factory Defaults

The Administration > Factory Defaults screen allows you to restore the Router’s configuration to its Router and/or voice factory default settings.

Diagnostics > Ping

Traceroute Test

The Traceroute test tests the performance of a connection.

IP or URL Address Enter the address of the PC whose connection you wish to test.

Start to Traceroute To run the test, click this button. The

Traceroute Test screen will show if the test was successful.

Click Close to return to the Diagnostics screen.


Administration > Factory Defaults

NOTE: Restoring factory defaults deletes custom settings. Note your custom settings before restoring the factory defaults.

Factory Defaults

Restore Router Factory Defaults To reset the Router settings to the default values, select Yes . Then click Save

Settngs . Any custom Router settings you have saved will be lost when the default settings are restored.

Restore Voce Factory Defaults To reset the voice settings to the default values, select Yes . Then click Save

Settngs . Any custom Voice settings you have saved will be lost when the default settings are restored.

NOTE: Restoring the voice defaults may require your login (the default user name and password are admn ). If the defaults do not work, contact your ITSP for more information.

2

Chapter3

On the Firmware Upgrade screen, click Save Settngs to apply your changes, or click Cancel Changes to cancel your changes.

Administration > Firmware Upgrade

The Firmware Upgrade screen allows you to upgrade the

Router’s firmware. Do not upgrade the firmware unless you are experiencing problems with the Router or the new firmware has a feature you want to use.

If you want to upgrade the Router’s firmware, then you may need a user name and password available only from your

ISP or ITSP. Contact your ISP or ITSP for more information.

Username & Password

If you see the Username & Password screen, enter the User

Name and Password provided by your ISP or ITSP. Then click Save Settngs .


Administration > Firmware Upgrade

Please select a fle to upgrade Click Browse and select the extracted firmware upgrade file.

Start to Upgrade After you have selected the appropriate file, click this button, and follow the on-screen instructions.

Administration > Config Management

The Config Management screen allows you to back up or restore the Router’s settings using a configuration file.

Administration > Username & Password

NOTE: The Router may lose the settings you have customized. Before you upgrade its firmware, use the Config Management screen to back up the Router’s settings. Refer to the

Administration > Config Management section for more information.

Firmware Upgrade

Before upgrading the firmware, download the Router’s firmware upgrade file from the Linksys website, www.linksys.com. Then extract the file.


Administration > Config Management

Backup Configuration

Backup To save the Router’s settings in a configuration file, click this button and follow the on-screen instructions.

Restore Configuration

To use this option, you must have previously backed up its configuration settings.

Please select a fle to restore Click the Browse button and select the Router’s configuration file.

Restore To restore the Router’s configuration settings, click this button and follow the on-screen instructions.

Status > Router

The Router screen displays information about the Router.

2

Chapter3


Status > Router

Router Information

Frmware Verson The version number of the Router’s current firmware is displayed.

Current Tme The time set on the Router is displayed.

Internet MAC Address The Router’s MAC address, as seen by your ISP, is displayed.

Router Name The name of the Router is displayed.

Host Name If required by your ISP, this was entered on the Basic Setup screen.

Doman Name If required by your ISP, this was entered on the Basic Setup screen.

Internet Connection

This section shows the current network information.

It varies depending on the Internet connection type selected on the Basic Setup screen.

Click Refresh to update the on-screen information.

Status > Local Network

The Local Network screen displays information about the local, wired network.

Status > Local Network

Local Network

Local MAC Address The MAC address of the Router’s local, wired interface is displayed.

Router IP Address The Router’s IP address, as it appears on your local network, is displayed.

Subnet Mask The Subnet Mask of the Router is displayed.

DHCP Server

DHCP Server The status of the Router’s DHCP server function is displayed.

Start IP Address For the range of IP addresses used by devices on your local network, the starting IP address is displayed.

End IP Address For the range of IP addresses used by devices on your local network, the ending IP address is displayed.

DHCP Clents Table Click this button to view a list of computers that are using the Router as a DHCP server.


DHCP Clients Table

DHCP Client Table

The DHCP Client Table lists computers and other devices that have been assigned IP addresses by the Router. The list can be sorted by Client Name, IP

Address, Interface, MAC Address, and Expires Time

(how much time is left for the current IP address). To

29

Chapter3 remove a DHCP client, click Delete . To retrieve the most up-to-date information, click Refresh . To exit this screen and return to the Local Network screen, click Close .

Status > Wireless Network

The Wireless Network screen displays information about your wireless network(s).

Advanced Configuration enter the user name and password provided by your ITSP.

Contact your ITSP for more information. (The factory default Admin Login name and password are admn .)

NOTE: In most cases, you do not need to use the administrative screens. Contact your ITSP for more information.

Voice > Info

The Info screen displays Voice over Internet Protocol (VoIP) information about the Router.

Status > Wireless Network

Wireless Network

Dynamc Channel Selecton The setting is displayed.

Channel The channel of the wireless network(s) is displayed.

Mode The wireless mode is displayed.

Wireless Network 1-2

Status information for each wireless network is displayed.

Wreless MAC Address The wireless MAC address of the

Router’s local, wireless interface is displayed.

Network Name (SSID) The network name, which is also called the SSID, is displayed.

Securty The wireless security method is displayed.

SSID Broadcast The status of the SSID Broadcast feature is displayed.

Access to the Voice Screens

There are two level of access, user and Admin Login. When you click the Voice tab, the Info screen is automatically displayed. If you set a User Password on the System screen, then you will be asked to enter it before the Info screen is displayed.

The Admin Login allows access to more advanced settings.

To access administrative screens, click Admn Logn , and


Voice > Info

Product Information

Product Name The model number of the Router is displayed.

Seral Number The serial number of the Router is displayed.

Software Verson The version number of the Router software is displayed.

30

Chapter3

Hardware Verson The version number of the Router hardware is displayed.

MAC Address The MAC address of the Router is displayed.

Clent Certfcate The status of the client certificate, which indicates that the Router has been authorized by your ITSP, is displayed.

System Status

Current Tme The current date and time of the Router are displayed.

Elapsed Tme The amount of time elapsed since the last reboot of the Router is displayed.

RTP Packets Sent The number of RTP packets sent by the

Router is displayed.

RTP Bytes Sent The number of RTP bytes sent by the


RTP Packets Recv The number of RTP packets received by the Router is displayed.

RTP Bytes Recv The number of RTP bytes received by the


SIP Messages Sent The number of SIP messages sent by the Router is displayed.

SIP Bytes Sent The number of SIP bytes sent by the


SIP Messages Recv The number of SIP messages received by the Router is displayed.

SIP Bytes Recv The number of SIP bytes received by the


External IP The external IP address used for NAT mapping is displayed.

Line 1/2 Status

Lines 1 and 2 have the same status information available.

Hook State The status of the Internet phone line’s readiness is displayed. “On” indicates that it is ready for use, while “Off” indicates that it is in use.

Regstraton State The status of the line’s registration with the ITSP is displayed.

Last Regstraton At The last date and time the line was registered are displayed.

Next Regstraton In The number of seconds until the next registration is displayed.

Message Watng This indicates whether you have new voicemail waiting.

Call Back Actve This indicates whether a call back request is in progress.



Last Called Number The last number called is displayed.

Last Caller Number The number of the last caller is displayed.

Mapped SIP Port The port number of the NAT mapped

SIP port is displayed.

Calls 1 and 2 have the same status information available.

Call 1/2 State The status of the call is displayed.

Call 1/2 Tone The type of tone used by the call is displayed.

Call 1/2 Encoder The codec used for encoding is displayed.

Call 1/2 Decoder The codec used for decoding is displayed.

Call 1/2 FAX The status of the fax pass-through mode is displayed.

Call 1/2 Type The direction of the call is displayed.

Call 1/2 Remote Hold This indicates whether the far end has placed the call on hold.

Call 1/2 Callback This indicates whether the call was triggered by a call back request.

Call 1/2 Peer Name The name of the internal phone is displayed.

Call 1/2 Peer Phone The phone number of the internal phone is displayed.

Call 1/2 Duraton The duration of the call is displayed.

Call 1/2 Packets Sent The number of packets sent is displayed.

Call 1/2 Packets Recv The number of packets received is displayed.

Call 1/2 Bytes Sent The number of bytes sent is displayed.

Call 1/2 Bytes Recv The number of bytes received is displayed.

Call 1/2 Decode Latency The number of milliseconds for decoder latency is displayed.

Call 1/2 Jtter The number of milliseconds for receiver jitter is displayed.

Call 1/2 Round Trp Delay The number of milliseconds for delay is displayed.

Call 1/2 Packets Lost The number of packets lost is displayed.

Call 1/2 Packet Error The number of invalid packets received is displayed.

Call 1/2 Mapped RTP Port The number of the NAT mapped RTP port is displayed.

31

Chapter3

Call 1/2 Meda Loopback The Media Loopback feature allows the ITSP to test the quality of the connection to the

Router. The status of the feature is displayed.

Voice > System

The System screen displays the User Password setting.


Voice > System

System Configuration

User Password Enter the password for user access to the

Voice screens. (By default, there is no password.)

Miscellaneous Settings

No settings are displayed.

Click Save Settngs to apply your change, or click Cancel

Changes to cancel your change.

Voice > User 1/2

The User 1 and 2 screens display similar settings. The User 1 screen displays settings for users of phone line 1, and the

User 2 screen displays settings for users of phone line 2.


Voice > User 1

Call Forward Settings

Enter the call forwarding numbers you want to use.

Cfwd All Dest Enter the number for the Call Forward All

Service feature (when you want to forward all calls).

Cfwd Busy Dest Enter the number for the Call Forward

Busy feature (when the line is busy).

Cfwd No Ans Dest Enter the number for the Call Forward

No Answer feature (when the line is not answered).

Cfwd No Ans Delay Enter the number of seconds to wait before the Call Forward No Answer feature is triggered.

The default is 20 .

Selective Call Forward Settings

Enter the caller numbers that will be forwarded to specific phone numbers.

Cfwd Sel1- Caller Enter the caller number pattern to trigger the Call Forward Selective (1-8) feature.

Cfwd Sel1- Dest Enter the forward number for the Call

Forward Selective (1-8) feature.

Cfwd Last Caller Enter the caller number that is actively forwarded to the Cfwd Last Dest number when the Call

Forward Last activation code is used.

Cfwd Last Dest Enter the forward number for the Cfwd

Last Caller feature.

32

Chapter3

Block Last Caller Enter the ID of the caller blocked via the Block Last Caller service.

Accept Last Caller Enter the ID of the caller accepted via the Accept Last Caller service.

Speed Dial Settings

Speed Dal 2-9 Enter the phone number for each Speed

Dial setting.

Supplementary Service Settings

CW Settng Select whether you want to use the Call

Waiting feature for all calls, yes or no . The default is yes .

Block CID Settng Select whether you want to block

Caller ID for all calls, yes or no . The default is no .

Block ANC Settng Select whether you want to block anonymous calls, yes or no . The default is no .

DND Settng Select whether you want to use the Do Not

Disturb (DND) feature, yes or no . The default is no .

CID Settng Select whether you want to enable Caller ID generation, yes or no . The default is yes .

CWCID Settng Select whether you want to enable Caller

ID for Call Waiting, yes or no . The default is yes .

Dst Rng Settng Select whether you want to use the

Distinctive Ring feature, yes or no . The default is yes .

Message Watng Select whether you want to use the

Message Waiting feature, yes or no . The default is no .

Distinctive Ring Settings

Rng1- Caller Enter the caller number pattern to play

Distinctive Ring/Call Waiting Tone (1-8).

Ring Settings

Default Rng Select the default ringing pattern for all callers. The default is 1 .

Default CWT Select the default CWT pattern for all callers.

The default is 1 .

Hold Remnder Rng Select the ring pattern that will remind you of a call on hold when the phone is on-hook.

The default is .

Call Back Rng Select the ring pattern for call back notification. The default is .

Cfwd Rng Splash Len Enter the duration of the ring splash when a call is forwarded. The range is 0 to 10.0 seconds. The default is 0 .

Cblk Rng Splash Len Enter the duration of the ring splash when a call is blocked. The range is 0 to 10.0 seconds. The default is 0 .



VMWI Rng Splash Len Enter the duration of the ring splash when new messages arrive before the VoiceMail

Waiting Indication (VMWI) signal is applied. The range is 0 to 10.0 seconds. The default is 0 .



Voice > Admin Login

The Admin Login allows access to more advanced settings.

To access administrative screens, click Admn Logn , and enter the user name and password provided by your ITSP.

Contact your ITSP for more information. (The factory default Admin Login name and password are admn .)

NOTE: In most cases, you do not need to use the administrative screens. Contact your ITSP for more information.

33

Chapter4

Chapter :

Interactve Voce

Response Menu

Overview

This chapter explains how to use the Interactive Voice

Response (IVR) Menu to configure the Router’s network settings. Use your telephone’s keypad to enter your commands and select choices, and the Router will use voice responses.

To access the IVR Menu:

1.

2.

3.

Use a telephone connected to the Phone 1 or 2 port of the Router. (You can only access the IVR Menu through an analog telephone, not any of the Internet phones.)

Press **** (in other words, press the star key four times).

Wait until you hear the Router’s response,

“Configuration menu. Please enter the option followed by the # (pound) key, or hang up to exit”.

Menu Commands

Refer to the following table that lists actions, commands, menu choices, and descriptions. After you select an option, press the # (pound) key. To exit the menu, hang up the telephone.

If the menu is inactive for more than one minute, the

Router will time out. To re-enter the menu, press **** .

Interactive Voice Response Menu

Acton

Enter IVR

Menu

Check IP

Address

Check

Subnet

Mask

Check Static

Gateway IP

Address

Check MAC

Address

Check

Firmware

Version

Factory

Reset of the

Router

Warning:

All custom settings will be lost, including the network and service provider data.

Command Choces Descrpton

****

Check DHCP 100

110

120

130

10

10

33 Confirm -

Press 1 .

Cancel -

Press *

(star).

Use this command to enter the IVR

Menu. Ignore

Special Information

Tones (SITs) or other tones until you hear, “Configuration menu. Please enter the option followed by the # (pound) key, or hang up to exit.”

The IVR announces whether DHCP is enabled or disabled.

The IVR announces the current IP address of the

Router.

The IVR announces the current subnet mask of the Router.

The IVR announces the current gateway

IP address of the

Router.

The IVR announces the MAC address of the Router in hexadecimal string format.

The IVR announces the version number of the firmware running on the

Router.

After the

Router requests confirmation, press

1 to confirm.

After you hear,

“Option successful”, hang up the phone.

The Router will reboot, and all settings will be reset to their defaults.


AppendixA

Appendx A:

Troubleshootng

Your computer cannot connect to the Internet.

Follow these instructions until your computer can connect to the Internet:

•

•

•

Make sure that the Router is powered on. The Power

LED should be green and not flashing.

If the Power LED is flashing, then power off all of your network devices, including the modem, Router, and computers. Wait 30 seconds. Then power on each device in the following order:

1.

Cable or DSL modem

2.

Router

3.

Computer

Check the cable connections. The computer should be connected to one of the ports numbered 1-4 on the Router, and the modem must be connected to the

Internet port on the Router.

You do not hear a dial tone, and the Phone 1 or 2 LED is not lit.

Follow these instructions until your problem is solved:

•

•

•

•

Make sure the telephone is plugged into the appropriate port, Phone 1 or 2.

Disconnect and re-connect the RJ-11 telephone cable between the Router and telephone.

Make sure your telephone is set to its tone setting

(not pulse).

2.

3.

Make sure your network has an active Internet connection. Try to access the Internet, and check to see if the Router’s Internet LED is lit. If you do not have a connection, then power off all of your network devices, including the modem, Router, and computers.

Wait 30 seconds. Then power on each device in the following order:

1.

Cable or DSL modem

Router

Computers and other devices

• Verify your account information and confirm that the phone line is registered with your Internet Telephony

Service Provider (ITSP).

Troubleshooting

When you are on an Internet phone call, words are dropped intermittently.

Follow these instructions until your problem is solved:

•

•

•

If you are using the Router’s wireless function and a cordless phone, they may be using the same frequency and may interfere with each other. Move the cordless phone farther away from the Router.

There may be heavy network activity, particularly if you are running a server or using a file sharing program.

Try to limit network or Internet activity during

Internet phone calls. For example, if you are running a file sharing program, files may be uploaded in the background even though you are not downloading any files, so make sure you exit the program before making Internet phone calls.

There may not be enough bandwidth available for your Internet phone call. You may want to test your bandwidth using one of the bandwidth tests available online. If necessary, access your Internet phone service account and reduce the bandwidth requirements for your service. For more information, refer to the website of your ITSP.

The modem does not have an Ethernet port.

The modem is a dial-up modem for traditional dial-up service. To use the Router, you need a cable/DSL modem and high-speed Internet connection.

You cannot use the DSL service to connect manually to the Internet.

After you have installed the Router, it will automatically connect to your Internet Service Provider (ISP) or Internet

Telephony Service Provider (ITSP), so you no longer need to connect manually.

The DSL telephone line does not fit into the Router’s

Internet port.

The Router does not replace your modem. You still need your DSL modem in order to use the Router. Connect the telephone line to the DSL modem, insert the setup

CD into your computer, and then follow the on-screen instructions.


AppendixA

When you double-click the web browser, you are prompted for a username and password. If you want to get rid of the prompt, follow these instructions.

3.

4.

Launch the web browser and perform the following steps

(these steps are specific to Internet Explorer but are similar for other browsers):

1.

2.

Select Tools > Internet Optons .

Click the Connectons tab.

Select Never dal a connecton .

Click OK .

The Router does not have a coaxial port for the cable connection.

The Router does not replace your modem. You still need your cable modem in order to use the Router. Connect your cable connection to the cable modem, insert the setup

CD into your computer, and then follow the on-screen instructions.

The computer cannot connect wirelessly to the network.

Make sure the wireless network name or SSID is the same on both the computer and the Router. If you have enabled wireless security, then make sure the same security method and key are used by both the computer and the

Router.

You need to modify the settings on the Router.

To access the web-based utility, follow these instructions:

1.

Launch the web browser on your computer, and enter the Router’s default IP address, 192.1.1.1

, in the

Address field. Then press Enter .

NOTE:

If you place the Router behind a primary router with the IP address of 192.168.15.1, then the Router will automatically assume a new default IP address, 192.1.1.1

.

2.

3.

A login screen appears. The first time you open the web-based utility, use the default user name and password, admn . (You can set a new password from the Administration tab’s Management screen.) Then click OK .

Click the appropriate tab to change the settings.

WEB:

If your questions are not addressed here, refer to the Linksys website, www.lnksys.com

.


Troubleshooting

3

AppendixB

Appendx B:

Specfcatons

Model WRP400

* Note: Many specifications are programmable within a defined range or list of options. Please see the SPA ATA

Administration Guide for details. The target configuration profile is uploaded to the WRP400 at the time of provisioning.

Data Networking MAC Address (IEEE 802.3)

IPv4 - Internet Protocol v4 (RFC 791)

Upgradeable to v6 (RFC 1883)

ARP - Address Resolution Protocol

DNS - A Record (RFC 1706),

SRV Record (RFC 2782)

DHCP Client - Dynamic Host

Configuration Protocol (RFC 2131)

DHCP Server - Dynamic Host

Configuration Protocol (RFC 2131)

PPPoE Client - Point to Point

Protocol over Ethernet (RFC 2516)

ICMP - Internet Control Message

Protocol (RFC792)

TCP - Transmission Control Protocol

(RFC793)

UDP - User Datagram Protocol

(RFC768)

RTP - Real Time Protocol (RFC 1889)

(RFC 1890)

RTCP - Real Time Control Protocol

(RFC 1889)

TFTP

RTSP

HTTP

NAT (RFC 1631)

Reverse NAT

SDP

SNTP - Simple Network Time

Protocol (RFC 2030)

Type of Service - TOS

(RFC 791/1349)

QoS - Packet Prioritization by Type

Router or Bridge Mode of

Operation

MAC Address Cloning

Port Forwarding


Specifications

IP Multicast / IGMP v1, v2, v3/

IGMP Proxy

Voice Features Voice Algorithms

G.711 (a-law and µ-law)

G.726 (16/24/32/40 kbps)

G.729 AB

G.723.1 (6.3 kbps, 5.3 kbps)

Call Forwarding:

No Answer/Busy/Unconditional

Support for Two Simultaneous Calls

SIP TLS (Transport Layer Security)

Call Transfer

Call Waiting/Hold/Retrieve

Three-way Conferencing

Call ID Number & Name (Primary

Line & On Call Waiting)

Call-ID Block (Prevent Send out the

Caller ID)

Anonymous Call Blocking

Distinctive Ringing

Do not Disturb Setting

Repeat Dialing on Busy

Call Return

Emergency Call Support

Dial Plan

Speed Dial

Auto-Attendant

Multi-Room Meet-Me Conference

In-Band/ SIP-INFO DTMF Translation

Provisioning,

Administration,

& Maintenance Web Browser Administration &

Configuration via Integral Web Server

Telephone Key Pad Configuration with Interactive Voice Prompts

Automated Provisioning & Upgrade via HTTP, TFTP, HTTPS

Asynchronous Notification of

Upgrade Availability via NOTIFY

Non-Intrusive, In-Service Upgrades

Report Generation & Event Logging

Stats in BYE Message

Syslog & Debug Server Records

Per Line and Purpose Configurable

Syslog and Debug Options

3

AppendixB

Physical Interfaces 4 100Base-T RJ-45 Ethernet Port

(IEEE 802.3)

2 RJ-11 FXS Phone Ports - For

Analog Circuit Telephone Device

Buttons

USB 2.0 (reserved for future use via firmware upgrade)

Reset, WPS

Subscriber Line

Interface Circuit

(SLIC) Ring Voltage: 40-90 Vpk

Ring Frequency: 20 to 25Hz

Ring Waveform: Trapezoidal with

1.2 to 1.6 Crest Factor

Maximum Ringer Load: 3 REN

On-Hook/Off-Hook Characteristics:

On-Hook Voltage (Tip/Ring):

- 46 to -56V

Off-Hook Current:

18 to 25mA

Terminating Impedance:

600 ohm Resistive

270 ohm + 750ohm//150nF

Complex Impedance

Regulatory

Compliance

Number of

Antennas

Frequency Response: 300 – 3400Hz

FCC (Part 15 Class B), CE, ICES-003,

RoHS

1

Connector type Fixed

Detachable (y/n) No

RF Pwr (EIRP) in dBm (Average, not Including Antenna)

802.11g: Typ. 18 dBm @ Normal

Temp Range (with PA)

802.11b: Typ: 20 dBm @ Normal

Temp Range (with PA)

Antenna Gain in dBi 2 dBi

UPnP able/cert Yes

Power Supply Switching Type (100-240V) Automatic

DC Input Voltage: +5 VDC at

2.0 A Max.

Power Consumption: 7.9 watts

(Average)

Power Adapter: 100-240V - 50-60Hz

(26-34VA) AC Input, 1.8 m Cord


Specifications

Indicator Lights/

LEDs Power, Ethernet, Wireless, Phone 1,

Phone 2, Internet, WPS

Documentation Quick Installation and User Guide are

Downloaded from www.linksys.com

Linksys SPA ATA Administration

Guide - Service Providers Only

Linksys Provisioning Guide - Service

Providers Only

Security Features Password-Protected Configuration for Web Access

Denial of Service (DoS) Prevention

URL Filtering, and Keyword, Java,

ActiveX, Proxy, Cookie Blocking

VPN Passthrough for IPSec, PPTP, and L2TP Protocols

64, 128 bits WEP with Passphrase

WEP Key Generation

SSID Broadcast Disable

Access Restriction by MAC and IP

Addresses

Wi-Fi Protected Setup (WPS),

Wi-Fi Protected Access™ (WPA),

Wi-Fi Protected Access™ 2 (WPA2)

Security Key Bits 64, 128

Envronmental

Dimensions

Weight

Power

5.51" x 5.51" x 1.06"

(140 x 140 x 27 mm)

10.05 oz (285 g)

External, Switching, 5VDC, 2A

Certification FCC, CE, CB, IC, UL,

Wi-Fi (802.11b + WPA2,

802.11g + WPA2, WMM)

Operating Temp. 0 to 40°C (32 to 104°F)

Storage Temp. -20 to 70°C (-4 to 158°F)

Operating

Humidity 10 to 85%, Relative Humidity,

Noncondensing

Storage Humidity 5 to 90% Noncondensing

3

AppendixC

Appendx C:

Warranty Informaton

Contact your servce provder f the warranty support ssues are to be handled by them as per your servce agreements.

Limited Warranty

Linksys warrants to You that, for a period of one year

(the “Warranty Period”), your Linksys Product will be substantially free of defects in materials and workmanship under normal use. Your exclusive remedy and Linksys’ entire liability under this warranty will be for Linksys at its option to repair or replace the Product or refund Your purchase price less any rebates. This limited warranty extends only to the original purchaser.

If the Product proves defective during the Warranty

Period call Linksys Technical Support in order to obtain a Return Authorization Number, if applicable. BE SURE

TO HAVE YOUR PROOF OF PURCHASE ON HAND WHEN

CALLING. If You are requested to return the Product, mark the Return Authorization Number clearly on the outside of the package and include a copy of your original proof of purchase. RETURN REQUESTS CANNOT BE PROCESSED

WITHOUT PROOF OF PURCHASE. You are responsible for shipping defective Products to Linksys. Linksys pays for UPS Ground shipping from Linksys back to You only.

Customers located outside of the United States of America and Canada are responsible for all shipping and handling charges.

ALL IMPLIED WARRANTIES AND CONDITIONS OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE ARE LIMITED TO THE DURATION OF THE

WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED

CONDITIONS, REPRESENTATIONS AND WARRANTIES,

INCLUDING ANY IMPLIED WARRANTY OF NON-

INFRINGEMENT, ARE DISCLAIMED. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to You. This warranty gives You specific legal rights, and You may also have other rights which vary by jurisdiction.

This warranty does not apply if the Product (a) has been altered, except by Linksys, (b) has not been installed, operated, repaired, or maintained in accordance with instructions supplied by Linksys, or (c) has been subjected to abnormal physical or electrical stress, misuse, negligence, or accident. In addition, due to the continual development of new techniques for intruding upon and attacking networks, Linksys does not warrant that the

Product will be free of vulnerability to intrusion or attack.

Warranty Information

TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT

WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE

OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL,

INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE

THEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISING

OUT OF OR RELATED TO THE USE OF OR INABILITY TO

USE THE PRODUCT (INCLUDING ANY SOFTWARE), EVEN

IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. IN NO EVENT WILL LINKSYS’ LIABILITY

EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT.

The foregoing limitations will apply even if any warranty or remedy provided under this Agreement fails of its essential purpose. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to You.

Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine,

CA 92623.


AppendixD

Appendx D:

Regulatory Informaton

FCC Statement

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•

•

Reorient or relocate the receiving antenna

Increase the separation between the equipment or devices

• Connect the equipment to an outlet other than the receiver’s

• Consult a dealer or an experienced radio/TV technician for assistance

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IEEE

802.11b or 802.11g operation of this product in the USA is firmware-limited to channels 1 through 11.

•

Safety Notices and Information

Caution: To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord.


Regulatory Information

•

•

Do not use this product near water, for example, in a wet basement or near a swimming pool.

Avoid using this product during an electrical storm.

There may be a remote risk of electric shock from lightning.

WARNING: This product contains lead, known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling.

WARNING: This equipment will be inoperable when main power fails.

WARNING: Many Internet phone service providers do not support calls to emergency service numbers (000 in Australia or 111 in New

Zealand). An alternative phone should be used to make emergency calls.

WARNING: To ensure compliance with explosure limits to radiofrequency fields, the antenna of the WRP400 should be no closer than 20 cm from the body during use.

Industry Canada Statement

1.

2.

This Class B digital apparatus complies with Canadian

ICES-003 and RSS210.

Operation is subject to the following two conditions:

This device may not cause interference and

This device must accept any interference, including interference that may cause undesired operation of the device.

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is not more than required for successful communication.

Industry Canada Radiation Exposure Statement

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance

20cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

0

AppendixD

Avis d’Industrie Canada

1.

2.

Cet appareil numérique de la classe B est conforme aux normes NMB-003 et RSS210 du Canada.

L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes : il ne doit pas produire de brouillage et il doit accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.

Afin de réduire le risque d’interférence aux autres utilisateurs, le type d’antenne et son gain doivent

être choisis de façon à ce que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne soit pas supérieure au niveau requis pour obtenir une communication satisfaisante.

Avis d’Industrie Canada concernant l’exposition aux radiofréquences :

Ce matériel est conforme aux limites établies par IC en matière d’exposition aux radiofréquences dans un environnement non contrôlé. Ce matériel doit être installé et utilisé à une distance d’au moins 20 cm entre l’antenne et le corps de l’utilisateur.

L’émetteur ne doit pas être placé près d’une autre antenne ou d’un autre émetteur, ou fonctionner avec une autre antenne ou un autre émetteur.

Wireless Disclaimer

The maximum performance for wireless is derived from

IEEE Standard 802.11 specifications. Actual performance can vary, including lower wireless network capacity, data throughput rate, range and coverage. Performance depends on many factors, conditions and variables, including distance from the access point, volume of network traffic, building materials and construction, operating system used, mix of wireless products used, interference and other adverse conditions.


Avis de non-responsabilité concernant les appareils sans fil

Les performances maximales pour les réseaux sans fil sont tirées des spécifications de la norme IEEE 802.11.

Les performances réelles peuvent varier, notamment en fonction de la capacité du réseau sans fil, du débit de la transmission de données, de la portée et de la couverture. Les performances dépendent de facteurs, conditions et variables multiples, en particulier de la distance par rapport au point d’accès, du volume du trafic réseau, des matériaux utilisés dans le bâtiment et du type de construction, du système d’exploitation et de la combinaison de produits sans fil utilisés, des interférences et de toute autre condition défavorable.

Telepermit Statement

The cabling between the phone port and the phone shall not exceed 100 metres.


AppendixD

Declaration of Conformity with Regard to

EU Directive 1999/5/EC (R&TTE Directive)

Compliance Information for 2,4-GHz and 5-GHz Wireless

Products Relevant to the EU and Other Countries Following the EU Directive 1999/5/EC (R&TTE Directive)

Б ъ л г а р с к и

[Bulgarian]

Това оборудване отговаря на съществените изисквания и приложими клаузи на

Директива 1999/5/ЕС.

Česky

[Czech]:

Toto zařízení je v souladu se základními požadavky a ostatními odpovídajícími ustanoveními Směrnice 1999/5/EC.

Dansk

[Danish]:

Deutsch

[German]:

Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i Direktiv 1999/5/EF.

Dieses Gerät entspricht den grundlegenden

Anforderungen und den weiteren entsprechenden Vorgaben der Richtlinie

1999/5/EU.

Eesti

[Estonian]:

See seade vastab direktiivi 1999/5/EÜ olulistele nõuetele ja teistele asjakohastele sätetele.

English:

Español

[Spanish]:

Ελληνική

[Greek]:

Français

[French]:

Íslenska

[Icelandic]:

This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directiva 1999/5/CE.

Αυτός ο εξοπλισµός είναι σε συµµόρφωση µε

τις ουσιώδεις απαιτήσεις και άλλες σχετικές

διατάξεις της Οδηγίας 1999/5/EC.

Cet appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la Directive 1999/5/EC.

Þetta tæki er samkvæmt grunnkröfum og

öðrum viðeigandi ákvæðum Tilskipunar

1999/5/EC.

Italiano

[Italian]:

Latviski

[Latvian]:

Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla

Direttiva 1999/5/CE.

Šī iekārta atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.

Lietuvių

[Lithuanian]:

Šis įrenginys tenkina 1999/5/EB Direktyvos esminius reikalavimus ir kitas šios direktyvos nuostatas.



Nederlands

[Dutch]:

Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde bepalingen van de Richtlijn 1999/5/EC.

Malti

[Maltese]:

Magyar

[Hungarian]:

Dan l-apparat huwa konformi mal-ħtiġiet essenzjali u l-provedimenti l-oħra rilevanti tad-Direttiva 1999/5/EC.

Ez a készülék teljesíti az alapvető követelményeket és más 1999/5/EK irányelvben meghatározott vonatkozó rendelkezéseket.

Norsk

[Norwegian]:

Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU-direktiv 1999/5/EF.

Polski

[Polish]:

Urządzenie jest zgodne z ogólnymi wymaganiami oraz szczególnymi warunkami określonymi Dyrektywą UE: 1999/5/EC.

Português

[Portuguese]:

Este equipamento está em conformidade com os requisitos essenciais e outras provisões relevantes da Directiva 1999/5/EC.

Română

[Romanian]

Slovensko

[Slovenian]:

Acest echipament este in conformitate cu cerintele esentiale si cu alte prevederi relevante ale Directivei 1999/5/EC.

Ta naprava je skladna z bistvenimi zahtevami in ostalimi relevantnimi pogoji Direktive

1999/5/EC.

Slovensky

[Slovak]:

Suomi

[Finnish]:

Toto zariadenie je v zhode so základnými požiadavkami a inými príslušnými nariadeniami direktív: 1999/5/EC.

Tämä laite täyttää direktiivin 1999/5/EY olennaiset vaatimukset ja on siinä asetettujen muiden laitetta koskevien määräysten mukainen.

Svenska

[Swedish]:

Denna utrustning är i överensstämmelse med de väsentliga kraven och andra relevanta bestämmelser i Direktiv 1999/5/EC.

For all products, the Declaration of Conformity (DofC) is available through one or more of these options:

•

•

A pdf file is included on the product’s CD.

A print copy is included with the product.

• A pdf file is available on the product’s webpage.

Visit www.lnksys.com/nternatonal and select your country or region. Then select your product.

If you need any other technical documentation, see the

“Technical Documents on www.linksys.com/international” section, as shown later in this appendix.

2

AppendixD

The following standards were applied during the assessment of the product against the requirements of the Directive 1999/5/EC:

•

•

Radio: EN 300 328 and/or EN 301 893 as applicable

EMC: EN 301 489-1, EN 301 489-17

• Safety: EN 60950 and either EN 50385 or EN 50371

Dynamic Frequency Selection (DFS) and Transmit Power

Control (TPC) are required for operation in the 5 GHz band.

DFS: The equipment meets the DFS requirements as defined in ETSI EN 301 893. This feature is required by the regulations to avoid interference with Radio Location

Services (radars).

TPC: For operation in the 5 GHz band, the maximum power level is 3 dB or more below the applicable limit. As such,

TPC is not required.

CE Marking

For the Linksys Wireless-N, -G, -B, and/or -A products, the following CE mark, notified body number (where applicable), and class 2 identifier are added to the equipment.

or or or

Check the CE label on the product to find out which notified body was involved during the assessment.



National Restrictions

This product may be used in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:

Ce produit peut être utilisé dans tous les pays de l’UE (et dans tous les pays ayant transposés la directive 1999/5/CE) sans aucune limitation, excepté pour les pays mentionnés cidessous:

Questo prodotto è utilizzabile in tutte i paesi EU (ed in tutti gli altri paesi che seguono le direttive EU 1999/5/EC) senza nessuna limitazione, eccetto per i paesii menzionati di seguito:

Das Produkt kann in allen EU Staaten ohne Einschränkungen eingesetzt werden (sowie in anderen Staaten die der EU

Direktive 1999/5/CE folgen) mit Außnahme der folgenden aufgeführten Staaten:

In the majority of the EU and other European countries, the 2,4- and 5-GHz bands have been made available for the use of wireless local area networks (LANs). The table labeled “Overview of Regulatory Requirements for

Wireless LANs” provides an overview of the regulatory requirements applicable for the 2,4- and 5-GHz bands.

Later in this document you will find an overview of countries in which additional restrictions or requirements or both are applicable.

The requirements for any country may evolve. Linksys recommends that you check with the local authorities for the latest status of their national regulations for both the

2,4- and 5-GHz wireless LANs.

Overvew of Regulatory Requrements for Wreless LANs

Frequency

Band (MHz)

Max Power Level

(EIRP) (mW)

Indoor

ONLY

Indoor &

Outdoor

2400-2483.5

100 X

5150-5350 † 200 X

5470-5725 † 1000 X

† Dynamic Frequency Selection and Transmit Power Control are required in the frequency ranges of 5250-5350 MHz and 5470-5725

MHz.

The following countries have restrictions and/or requirements in addition to those given in the table labeled “Overview of Regulatory Requirements for

Wireless LANs”:

Denmark

In Denmark, the band 5150 - 5350 MHz is also allowed for outdoor usage.

I Danmark må frekvensbåndet 5150 - 5350 også anvendes udendørs.

3

AppendixD

France

For 2,4 GHz, the product should not be used outdoors in the band 2454 - 2483,5 MHz. There are no restrictions when used in other parts of the 2,4 GHz band when used indoors. Check http://www.arcep.fr/ for more details.

Pour la bande 2,4 GHz, l’ équipement ne doit pas être utilisé en extérieur dans la bande 2454 - 2483,5 MHz. Il n’y a pas de restrictions pour des utilisations en intérieur dans d’autres parties de la bande 2,4GHz. Consultez http://www.arcep.fr/ pour de plus amples détails.

Location

Applcable Power Levels n France

Frequency

Range (MHz)

Power (EIRP)

Indoor

(No restrictions)

2400-2483.5

100 mW (20 dBm)

Outdoor

2400-2454

2454-2483.5

100 mW (20 dBm)

10 mW (10 dBm)

Italy

This product meets the National Radio Interface and the requirements specified in the National Frequency

Allocation Table for Italy. Unless this 2,4-GHz wireless LAN product is operating within the boundaries of the owner’s property, its use requires a “general authorization”. Please check http://www.comunicazioni.it/it/ for more details.

Questo prodotto è conforme alla specifiche di Interfaccia

Radio Nazionali e rispetta il Piano Nazionale di ripartizione delle frequenze in Italia. Se non viene installato all’interno del proprio fondo, l’utilizzo di prodotti Wireless LAN a

2,4 GHz richiede una “Autorizzazione Generale”. Consultare http://www.comunicazioni.it/it/ per maggiori dettagli.

Latvia

The outdoor usage of the 2,4 GHz band requires an authorization from the Electronic Communications Office.

Please check http://www.esd.lv for more details.

2,4 GHz frekveču joslas izmantošanai ārpus telpām nepieciešama atļauja no Elektronisko sakaru direkcijas.

Vairāk informācijas: http://www.esd.lv.

Notes:

1.

2.

Although Norway, Switzerland and Liechtenstein are not EU member states, the EU Directive 1999/5/EC has also been implemented in those countries.

The regulatory limits for maximum output power are specified in EIRP. The EIRP level of a device can be calculated by adding the gain of the antenna used

(specified in dBi) to the output power available at the connector (specified in dBm).



Product Usage Restrictions

This product is designed for indoor usage only. Outdoor usage is not recommended, unless otherwise noted.

2,4 GHz Restrictions

This product is designed for use with the standard, integral or dedicated (external) antenna(s) that is/are shipped together with the equipment. However, some applications may require the antenna(s), if removable, to be separated from the product and installed remotely from the device by using extension cables. For these applications, Linksys offers an R-SMA extension cable (AC9SMA) and an R-TNC extension cable (AC9TNC). Both of these cables are 9 meters long and have a cable loss (attenuation) of 5 dB. To compensate for the attenuation, Linksys also offers higher gain antennas, the HGA7S (with R-SMA connector) and

HGA7T (with R-TNC connector). These antennas have a gain of 7 dBi and may only be used with either the R-SMA or R-TNC extension cable.

Combinations of extension cables and antennas resulting in a radiated power level exceeding 100 mW EIRP are illegal.

Third-Party Software or Firmware

The use of software or firmware not supported/provided by Linksys may result that the equipment is no longer compliant with the regulatory requirements.

4.

5.

2.

3.

6.

7.

Technical Documents on www.linksys.com/international

Follow these steps to access technical documents:

1.

Enter http://www.linksys.com/international in your web browser.

Select the country or region in which you live.

Click the Products tab.

Select the appropriate product category.

Select the product sub-category, if necessary.

Select the product.

Select the type of documentation you want from the

More Information section. The document will open in PDF format if you have Adobe Acrobat installed on your computer.

NOTE: If you have questions regarding the compliance of this product or you cannot find the information you need, please contact your local sales office or visit www.lnksys.com/nternatonal

AppendixD

User Information for Consumer Products

Covered by EU Directive 2002/96/EC on

Waste Electric and Electronic Equipment

(WEEE)

This document contains important information for users with regards to the proper disposal and recycling of

Linksys products. Consumers are required to comply with this notice for all electronic products bearing the following symbol:

Englsh - Envronmental Informaton for Customers n the European Unon

European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.

Български (Bulgaran) - Информация относно опазването на околната среда за потребители в

Европейския съюз

Европейска директива 2002/96/EC изисква уредите, носещи този символ върху изделието и/или опаковката му, да не се изхвърля т с несортирани битови отпадъци. Символът обозначава, че изделието трябва да се изхвърля отделно от сметосъбирането на обикновените битови отпадъци. Ваша е отговорността този и другите електрически и електронни уреди да се изхвърлят в предварително определени от държавните или общински органи специализирани пунктове за събиране. Правилното изхвърляне и рециклиране ще спомогнат да се предотвратят евентуални вредни за околната среда и здравето на населението последствия. За по-подробна информация относно изхвърлянето на вашите стари уреди се обърнете към местните власти, службите за сметосъбиране или магазина, от който сте закупили уреда.


Ceštna (Czech) - Informace o ochraně žvotního prostředí pro zákazníky v zemích Evropské une

Evropská směrnice 2002/96/ES zakazuje, aby zařízení označené tímto symbolem na produktu anebo na obalu bylo likvidováno s netříděným komunálním odpadem. Tento symbol udává, že daný produkt musí být likvidován odděleně od běžného komunálního odpadu. Odpovídáte za likvidaci tohoto produktu a dalších elektrických a elektronických zařízení prostřednictvím určených sběrných míst stanovených vládou nebo místními

úřady. Správná likvidace a recyklace pomáhá předcházet potenciálním negativním dopadům na životní prostředí a lidské zdraví. Podrobnější informace o likvidaci starého vybavení si laskavě vyžádejte od místních úřadů, podniku zabývajícího se likvidací komunálních odpadů nebo obchodu, kde jste produkt zakoupili.

Dansk (Dansh) - Mljønformaton for kunder EU

EU-direktiv 2002/96/EF kræver, at udstyr der bærer dette symbol

på produktet og/eller emballagen ikke må bortskaffes som usorteret kommunalt affald. Symbolet betyder, at dette produkt skal bortskaffes adskilt fra det almindelige husholdningsaffald.

Det er dit ansvar at bortskaffe dette og andet elektrisk og elektronisk udstyr via bestemte indsamlingssteder udpeget af staten eller de lokale myndigheder. Korrekt bortskaffelse og genvinding vil hjælpe med til at undgå mulige skader for miljøet og menneskers sundhed. Kontakt venligst de lokale myndigheder, renovationstjenesten eller den butik, hvor du har købt produktet, angående mere detaljeret information om bortskaffelse af dit gamle udstyr.

Deutsch (German) - Umweltnformaton für Kunden nnerhalb der Europäschen Unon

Die Europäische Richtlinie 2002/96/EC verlangt, dass technische

Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem Symbol versehen ist , nicht zusammen mit unsortiertem

Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses

Gerät und andere elektrische und elektronische Geräte über die dafür zuständigen und von der Regierung oder örtlichen

Behörden dazu bestimmten Sammelstellen zu entsorgen.

Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei, potentielle negative Folgen für Umwelt und die menschliche

Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur

Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das Produkt erworben haben.


AppendixD

Eest (Estonan) - Keskkonnaalane nformatsoon

Euroopa Ldus asuvatele klentdele

Euroopa Liidu direktiivi 2002/96/EÜ nõuete kohaselt on seadmeid, millel on tootel või pakendil käesolev sümbol , keelatud kõrvaldada koos sorteerimata olmejäätmetega. See sümbol näitab, et toode tuleks kõrvaldada eraldi tavalistest olmejäätmevoogudest. Olete kohustatud kõrvaldama käesoleva ja ka muud elektri- ja elektroonikaseadmed riigi või kohalike ametiasutuste poolt ette nähtud kogumispunktide kaudu.

Seadmete korrektne kõrvaldamine ja ringlussevõtt aitab vältida võimalikke negatiivseid tagajärgi keskkonnale ning inimeste tervisele. Vanade seadmete kõrvaldamise kohta täpsema informatsiooni saamiseks võtke palun ühendust kohalike ametiasutustega, jäätmekäitlusfirmaga või kauplusega, kust te toote ostsite.

Español (Spansh) - Informacón medoambental para clentes de la Unón Europea

La Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación. Es responsabilidad suya desechar este y cualesquiera otros aparatos eléctricos y electrónicos a través de los puntos de recogida que ponen a su disposición el gobierno y las autoridades locales. Al desechar y reciclar correctamente estos aparatos estará contribuyendo a evitar posibles consecuencias negativas para el medio ambiente y la salud de las personas. Si desea obtener información más detallada sobre la eliminación segura de su aparato usado, consulte a las autoridades locales, al servicio de recogida y eliminación de residuos de su zona o pregunte en la tienda donde adquirió el producto.

ξλληνικά (Greek) - Στοιχεία περιβαλλοντικής

προστασίας για πελάτες εντός της Ευρωπαϊκής

Ένωσης

Η Κοινοτική Οδηγία 2002/96/EC απαιτεί ότι ο εξοπλισμός ο οποίος

φέρει αυτό το σύμβολο στο προϊόν και/ή στη συσκευασία

του δεν πρέπει να απορρίπτεται μαζί με τα μικτά κοινοτικά

απορρίμματα. Το σύμβολο υποδεικνύει ότι αυτό το προϊόν θα

πρέπει να απορρίπτεται ξεχωριστά από τα συνήθη οικιακά

απορρίμματα. Είστε υπεύθυνος για την απόρριψη του παρόντος

και άλλου ηλεκτρικού και ηλεκτρονικού εξοπλισμού μέσω των

καθορισμένων εγκαταστάσεων συγκέντρωσης απορριμμάτων οι

οποίες παρέχονται από το κράτος ή τις αρμόδιες τοπικές αρχές.

Η σωστή απόρριψη και ανακύκλωση συμβάλλει στην πρόληψη

πιθανών αρνητικών συνεπειών για το περιβάλλον και την υγεία.

Για περισσότερες πληροφορίες σχετικά με την απόρριψη του

παλιού σας εξοπλισμού, παρακαλώ επικοινωνήστε με τις τοπικές

αρχές, τις υπηρεσίες απόρριψης ή το κατάστημα από το οποίο

αγοράσατε το προϊόν.


Franças (French) - Informatons envronnementales pour les clents de l’Unon européenne

La directive européenne 2002/96/CE exige que l’équipement sur lequel est apposé ce symbole sur le produit et/ou son emballage ne soit pas jeté avec les autres ordures ménagères. Ce symbole indique que le produit doit être éliminé dans un circuit distinct de celui pour les déchets des ménages. Il est de votre responsabilité de jeter ce matériel ainsi que tout autre matériel

électrique ou électronique par les moyens de collecte indiqués par le gouvernement et les pouvoirs publics des collectivités territoriales. L’élimination et le recyclage en bonne et due forme ont pour but de lutter contre l’impact néfaste potentiel de ce type de produits sur l’environnement et la santé publique. Pour plus d’informations sur le mode d’élimination de votre ancien

équipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des déchets, ou l’endroit où vous avez acheté le produit.

Italano (Italan) - Informazon relatve all’ambente per clent resdent nell’Unone Europea

La direttiva europea 2002/96/EC richiede che le apparecchiature contrassegnate con questo simbolo sul prodotto e/o sull’imballaggio non siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve essere smaltito insieme ai normali rifiuti domestici. È responsabilità del proprietario smaltire sia questi prodotti sia le altre apparecchiature elettriche ed elettroniche mediante le specifiche strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze potenzialmente negative per l’ambiente e per la salute dell’essere umano. Per ricevere informazioni più dettagliate circa lo smaltimento delle vecchie apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel quale avete acquistato il prodotto.

Latvešu valoda (Latvan) - Ekoloģska nformācja klentem Eropas Savenības jursdkcjā

Direktīvā 2002/96/EK ir prasība, ka aprīkojumu, kam pievienota zīme uz paša izstrādājuma vai uz tā iesaiņojuma, nedrīkst izmest nešķirotā veidā kopā ar komunālajiem atkritumiem

(tiem, ko rada vietēji iedzīvotāji un uzņēmumi). Šī zīme nozīmē to, ka šī ierīce ir jāizmet atkritumos tā, lai tā nenonāktu kopā ar parastiem mājsaimniecības atkritumiem. Jūsu pienākums ir šo un citas elektriskas un elektroniskas ierīces izmest atkritumos, izmantojot īpašus atkritumu savākšanas veidus un līdzekļus, ko nodrošina valsts un pašvaldību iestādes. Ja izmešana atkritumos un pārstrāde tiek veikta pareizi, tad mazinās iespējamais kaitējums dabai un cilvēku veselībai. Sīkākas ziņas par novecojuša aprīkojuma izmešanu atkritumos jūs varat saņemt vietējā pašvaldībā, atkritumu savākšanas dienestā, kā arī veikalā, kur iegādājāties šo izstrādājumu.


AppendixD

Letuvška (Lthuanan) - Aplnkosaugos nformacja, skrta Europos Sąjungos vartotojams

Europos direktyva 2002/96/EC numato, kad įrangos, kuri ir kurios pakuotė yra pažymėta šiuo simboliu (įveskite simbolį), negalima šalinti kartu su nerūšiuotomis komunalinėmis atliekomis. Šis simbolis rodo, kad gaminį reikia šalinti atskirai nuo bendro buitinių atliekų srauto. Jūs privalote užtikrinti, kad

ši ir kita elektros ar elektroninė įranga būtų šalinama per tam tikras nacionalinės ar vietinės valdžios nustatytas atliekų rinkimo sistemas. Tinkamai šalinant ir perdirbant atliekas, bus išvengta galimos žalos aplinkai ir žmonių sveikatai. Daugiau informacijos apie jūsų senos įrangos šalinimą gali pateikti vietinės valdžios institucijos, atliekų šalinimo tarnybos arba parduotuvės, kuriose įsigijote tą gaminį.

Malt (Maltese) - Informazzjon Ambjental għal Kljent fl-Unjon Ewropea

Id-Direttiva Ewropea 2002/96/KE titlob li t-tagħmir li jkun fih issimbolu fuq il-prodott u/jew fuq l-ippakkjar ma jistax jintrema ma’ skart muniċipali li ma ġiex isseparat. Is-simbolu jindika li dan il-prodott għandu jintrema separatament minn ma’ liskart domestiku regolari. Hija responsabbiltà tiegħek li tarmi dan it-tagħmir u kull tagħmir ieħor ta’ l-elettriku u elettroniku permezz ta’ faċilitajiet ta’ ġbir appuntati apposta mill-gvern jew mill-awtoritajiet lokali. Ir-rimi b’mod korrett u r-riċiklaġġ jgħin jipprevjeni konsegwenzi negattivi potenzjali għall-ambjent u għas-saħħa tal-bniedem. Għal aktar informazzjoni dettaljata dwar ir-rimi tat-tagħmir antik tiegħek, jekk jogħġbok ikkuntattja lill-awtoritajiet lokali tiegħek, is-servizzi għar-rimi ta’ l-iskart, jew il-ħanut minn fejn xtrajt il-prodott.

Magyar (Hungaran) - Környezetvédelm nformácó az európa unós vásárlók számára

A 2002/96/EC számú európai uniós irányelv megkívánja, hogy azokat a termékeket, amelyeken, és/vagy amelyek csomagolásán az alábbi címke megjelenik, tilos a többi szelektálatlan lakossági hulladékkal együtt kidobni. A címke azt jelöli, hogy az adott termék kidobásakor a szokványos háztartási hulladékelszállítási rendszerektõl elkülönített eljárást kell alkalmazni. Az Ön felelõssége, hogy ezt, és más elektromos és elektronikus berendezéseit a kormányzati vagy a helyi hatóságok által kijelölt gyűjtõredszereken keresztül számolja fel. A megfelelõ hulladékfeldolgozás segít a környezetre és az emberi egészségre potenciálisan ártalmas negatív hatások megelõzésében. Ha elavult berendezéseinek felszámolásához további részletes információra van szüksége, kérjük, lépjen kapcsolatba a helyi hatóságokkal, a hulladékfeldolgozási szolgálattal, vagy azzal

üzlettel, ahol a terméket vásárolta.


Nederlands (Dutch) - Mleu-nformate voor klanten n de Europese Une

De Europese Richtlijn 2002/96/EC schrijft voor dat apparatuur die is voorzien van dit symbool op het product of de verpakking, niet mag worden ingezameld met niet-gescheiden huishoudelijk afval. Dit symbool geeft aan dat het product apart moet worden ingezameld. U bent zelf verantwoordelijk voor de vernietiging van deze en andere elektrische en elektronische apparatuur via de daarvoor door de landelijke of plaatselijke overheid aangewezen inzamelingskanalen. De juiste vernietiging en recycling van deze apparatuur voorkomt mogelijke negatieve gevolgen voor het milieu en de gezondheid. Voor meer informatie over het vernietigen van uw oude apparatuur neemt u contact op met de plaatselijke autoriteiten of afvalverwerkingsdienst, of met de winkel waar u het product hebt aangeschaft.

Norsk (Norwegan) - Mljønformasjon for kunder EU

EU-direktiv 2002/96/EF krever at utstyr med følgende symbol

avbildet på produktet og/eller pakningen, ikke må kastes sammen med usortert avfall. Symbolet indikerer at dette produktet skal håndteres atskilt fra ordinær avfallsinnsamling for husholdningsavfall. Det er ditt ansvar å kvitte deg med dette produktet og annet elektrisk og elektronisk avfall via egne innsamlingsordninger slik myndighetene eller kommunene bestemmer. Korrekt avfallshåndtering og gjenvinning vil være med på å forhindre mulige negative konsekvenser for miljø og helse. For nærmere informasjon om håndtering av det kasserte utstyret ditt, kan du ta kontakt med kommunen, en innsamlingsstasjon for avfall eller butikken der du kjøpte produktet.

Polsk (Polsh) - Informacja dla klentów w Un

Europejskej o przepsach dotyczących ochrony środowska

Dyrektywa Europejska 2002/96/EC wymaga, aby sprzęt oznaczony symbolem znajdującym się na produkcie i/lub jego opakowaniu nie był wyrzucany razem z innymi niesortowanymi odpadami komunalnymi. Symbol ten wskazuje, że produkt nie powinien być usuwany razem ze zwykłymi odpadami z gospodarstw domowych. Na Państwu spoczywa obowiązek wyrzucania tego i innych urządzeń elektrycznych oraz elektronicznych w punktach odbioru wyznaczonych przez władze krajowe lub lokalne. Pozbywanie się sprzętu we właściwy sposób i jego recykling pomogą zapobiec potencjalnie negatywnym konsekwencjom dla środowiska i zdrowia ludzkiego. W celu uzyskania szczegółowych informacji o usuwaniu starego sprzętu, prosimy zwrócić się do lokalnych władz, służb oczyszczania miasta lub sklepu, w którym produkt został nabyty.


AppendixD

Português (Portuguese) - Informação ambental para clentes da Unão Europea

A Directiva Europeia 2002/96/CE exige que o equipamento que exibe este símbolo no produto e/ou na sua embalagem não seja eliminado junto com os resíduos municipais não separados. O símbolo indica que este produto deve ser eliminado separadamente dos resíduos domésticos regulares.

É da sua responsabilidade eliminar este e qualquer outro equipamento eléctrico e electrónico através das instalações de recolha designadas pelas autoridades governamentais ou locais. A eliminação e reciclagem correctas ajudarão a prevenir as consequências negativas para o ambiente e para a saúde humana. Para obter informações mais detalhadas sobre a forma de eliminar o seu equipamento antigo, contacte as autoridades locais, os serviços de eliminação de resíduos ou o estabelecimento comercial onde adquiriu o produto.

Română (Romanan) - Informaţ de medu pentru clenţ dn Ununea Europeană

Directiva europeană 2002/96/CE impune ca echipamentele care prezintă acest simbol pe produs şi/sau pe ambalajul acestuia să nu fie casate împreună cu gunoiul menajer municipal. Simbolul indică faptul că acest produs trebuie să fie casat separat de gunoiul menajer obişnuit. Este responsabilitatea dvs. să casaţi acest produs şi alte echipamente electrice şi electronice prin intermediul unităţilor de colectare special desemnate de guvern sau de autorităţile locale. Casarea şi reciclarea corecte vor ajuta la prevenirea potenţialelor consecinţe negative asupra sănătăţii mediului şi a oamenilor. Pentru mai multe informaţii detaliate cu privire la casarea acestui echipament vechi, contactaţi autorităţile locale, serviciul de salubrizare sau magazinul de la care aţi achiziţionat produsul.

Slovenčna (Slovak) - Informáce o ochrane žvotného prostreda pre zákazníkov v Európskej ún

Podľa európskej smernice 2002/96/ES zariadenie s týmto symbolom na produkte a/alebo jeho balení nesmie byť likvidované spolu s netriedeným komunálnym odpadom.

Symbol znamená, že produkt by sa mal likvidovať oddelene od bežného odpadu z domácností. Je vašou povinnosťou likvidovať toto i ostatné elektrické a elektronické zariadenia prostredníctvom špecializovaných zberných zariadení určených vládou alebo miestnymi orgánmi. Správna likvidácia a recyklácia pomôže zabrániť prípadným negatívnym dopadom na životné prostredie a zdravie ľudí. Ak máte záujem o podrobnejšie informácie o likvidácii starého zariadenia, obráťte sa, prosím, na miestne orgány, organizácie zaoberajúce sa likvidáciou odpadov alebo obchod, v ktorom ste si produkt zakúpili.


Slovenčna (Slovene) - Okoljske nformacje za stranke v Evropsk unj

Evropska direktiva 2002/96/EC prepoveduje odlaganje opreme, označene s tem simbolom – na izdelku in/ali na embalaži – med običajne, nerazvrščene odpadke. Ta simbol opozarja, da je treba izdelek odvreči ločeno od preostalih gospodinjskih odpadkov.

Vaša odgovornost je, da to in preostalo električno in elektronsko opremo odnesete na posebna zbirališča, ki jih določijo državne ustanove ali lokalna uprava. S pravilnim odlaganjem in recikliranjem boste preprečili morebitne škodljive vplive na okolje in zdravje ljudi. Če želite izvedeti več o odlaganju stare opreme, se obrnite na lokalno upravo, odpad ali trgovino, kjer ste izdelek kupili.

Suom (Fnnsh) - Ympärstöä koskeva tetoja EUalueen asakkalle

EU-direktiivi 2002/96/EY edellyttää, että jos laitteistossa on tämä symboli itse tuotteessa ja/tai sen pakkauksessa, laitteistoa ei saa hävittää lajittelemattoman yhdyskuntajätteen mukana.

Symboli merkitsee sitä, että tämä tuote on hävitettävä erillään tavallisesta kotitalousjätteestä. Sinun vastuullasi on hävittää tämä elektroniikkatuote ja muut vastaavat elektroniikkatuotteet viemällä tuote tai tuotteet viranomaisten määräämään keräyspisteeseen. Laitteiston oikea hävittäminen estää mahdolliset kielteiset vaikutukset ympäristöön ja ihmisten terveyteen. Lisätietoja vanhan laitteiston oikeasta hävitystavasta saa paikallisilta viranomaisilta, jätteenhävityspalvelusta tai siitä myymälästä, josta ostit tuotteen.

Svenska (Swedsh) - Mljönformaton för kunder

Europeska unonen

Det europeiska direktivet 2002/96/EC kräver att utrustning med denna symbol på produkten och/eller förpackningen inte får kastas med osorterat kommunalt avfall. Symbolen visar att denna produkt bör kastas efter att den avskiljts från vanligt hushållsavfall.

Det faller på ditt ansvar att kasta denna och annan elektrisk och elektronisk utrustning på fastställda insamlingsplatser utsedda av regeringen eller lokala myndigheter. Korrekt kassering och

återvinning skyddar mot eventuella negativa konsekvenser för miljön och personhälsa. För mer detaljerad information om kassering av din gamla utrustning kontaktar du dina lokala myndigheter, avfallshanteringen eller butiken där du köpte produkten.

WEB: For additional information, please visit www.lnksys.com


7102310A-JL

No results