- 1 -

Table Of Contents

Important Safety Instructions--------------------------------------------------- 1

Characteristic Features----------------------------------------------------------- 2

Accessory List------------------------------------------------------------------------ 3

Front Panel---------------------------------------------------------------------------- 4

Rear Panel----------------------------------------------------------------------------- 5

Remote Control---------------------------------------------------------------------- 6

System Connections--------------------------------------------------------------- 9

Connecting to Power Supply------------------------------------------------------- 9

Connecting to External AV Input Device (AV Output) ----------------------- 9

Connecting to TV Antenna---------------------------------------------------------

TV Function-------------------------------------------------------------------------- 14

Image Setting------------------------------------------------------------------------- 14

Audio Setting-------------------------------------------------------------------------- 16

Timer Setting-------------------------------------------------------------------------- 17

Setup Setting--------------------------------------------------------------------------

NICAM Function-------------------------------------------------------------------- 21

Other Functions-------------------------------------------------------------------- 22

External AV Input Function-------------------------------------------------------- 22

Computer Screen Function------------------------------------------------------- 22

Troubleshooting-------------------------------------------------------------------- 23

Specifications----------------------------------------------------------------------24

Important Safety Instructions

Caution

This symbol indicates that dangerous voltage instituting a risk of electric shock is present within this unit.

This symbol indicates that there are

8. Install according to the manufacturer instructions. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. maintenance instructions in the literature accompanying the appliance.

ensure correct and safe installation and interconnection of the apparatus.

10. The apparatus shall not be exposed to dripping or splashing and that no objects

1. The product contains a low-power device. In order to ensure the safety of the laser device, do not remove any cover and attempt to repair the unit. If any service needed, please contact the distributor or its authorized service center.

2. To reduce the risk of electric shock, do not remove the cover (back). No user-serviceable parts inside. Refer serving to qualified service personnel. Unplug the product from the wall outlet before serving or when it is unused for a long period of time.

3. The manufacturer should not hold responsibility for the damage caused by any substitutions and modification of the product without authorization from the manufacturer’s or authorized unit.

WARNING

The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

NOTES

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Following all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. filled with liquids, such as vases, shall be placed on the apparatus.

11. The mains socket-outlet shall be installed near the apparatus and the mains plug shall remain readily operable.

12. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. specified by the manufacturer.

14. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

15. Unplug the apparatus during lightning storms or when unused for long periods of time.

16.

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

NOTE: Do not touch the color TFT LCD screen by hand directly.

- 1 -

Characteristic Features

This product incorporates LCD display and TV receiver in one system.

Multiple Mode

TV mode

CVBS mode

S-VIDEO mode

COMPONENT mode

VGA mode

High Quality Property

LCD (Liquid Crystal Display)

Designed with 19" color TFT liquid crystal display clearly shows the data.

Stereo amplifier

Built-in 2x5W speakers provide high quality sound.

AV and VGA Input

Can be connected to external audio and video signal source and PC.

Special Function

Support sleep time setting function and favorite channel setting function, etc.

Multi-audio and Multi-video modes

Support multi-audio and multi-video modes, provide more selecting.

Auto TV Searching Function

Can be connected to the TV antenna, support Auto and manual TV programs searching function.

NICAM Function

Supports the NICAM function. According to the broadcasting programs, you can choose the corresponding soundtrack.

NOTE: It is normal for a TFT screen to experience some light or dark spots appearing on the LCD screen.

- 2 -

Accessory List

ITEM NAME QTY

Remote Control (with batteries) 1

Power Adaptor 1

Power Supply Cord 1

Audio/Video Cable 1

Operation Manual 1

NOTE

¾ Accessories and their parts numbers are subject to modification without prior notice due to improvements.

¾ The accessory images are supplied for reference only.

- 3 -

Front Panel

1. 19" color TFT screen

19" color TFT screen clearly show the data.

In setup menu, the same function as

◄ / ► direction buttons.

Press to select mode among TV, CVBS,

S-VIDEO, Component and VGA.

In setup menu, the same function as

ENTER button.

Press to enter or exit the standby mode.

7. Earphone

When connected to earphone, the internal speakers will automatically turn off.

Remote sensor window for the remote control. Press to enter or return to the previous setup menu.

▲ / ▼ button

In the TV mode, press to select channels.

In setup menu, the same function as ▲ / ▼ direction buttons.

▲ / ▼ button

In the TV mode, press to decrease or increase the volume.

10. Speakers

In normal playback status, it is blue; in standby mode, it turns red.

Two speakers output high quality stereo sound.

- 4 -

Rear Panel

1. Y/Pb/Pr Input Jack 5. TV Signal Input Jack

Connected to the Y/Pb/Pr input in

COMPONENT mode.

2. Y/Pb/Pr L/R Audio Input Jack

Connected to the L/R audio input in

COMPONENT mode.

3. Composite Audio/Video Output Jack

In the CVBS mode, connected to output the Audio/Video signals.

4. S-VIDEO and CVBS Audio/Video Input

Jack

Connected to the S-VIDEO input in

S-VIDEO mode or CVBS input in the

CVBS mode. The L/R audio input jacks can be used in the both S-VIDEO and

CVBS modes.

Connected for the external TV signal input.

6. DC 12V Input Jack

Connect the power adaptor or the car adaptor.

7. VGA Input Jack

Connected to the VGA output jack on a personal computer.

8. PC AUDIO Input Jack

Connected to the PC audio output jack.

- 5 -

Remote Control

Remote Control Drawing

Press to turn on or off this unit.

Press to shift to TV mode.

Press to shift to CVBS mode.

Press to shift the screen picture modes among User, Standard, Soft, Brightness and Shine.

5. S.M. button

Press to shift the sound modes among

User, Standard, Music, Movie and Speech.

6. 0~9 Number buttons

Press to select numbers such as TV channel.

Press to shift sound track when in TV mode (Please see P21 for details).

Press to increase or decrease the volume.

Press to turn on or off speaker output.

10. EXIT button

Press to exit from the setup menu.

11. Direction buttons ( ▲▼ ◄► )

In the setup menu, press the ▲▼ button to select a desired item and press the ◄► button to adjust.

12. ENTER button

Press to confirm your selection.

13. SOURCE button

Press to select mode among TV, CVBS,

S-VIDEO, COMPONENT and VGA.

14. Color buttons

Under teletext mode, they’re the teletext color buttons.

15. buttons

Under TV, CVBS or S-Video mode, press to display/close the teletext.

- 6 -

Remote Control

16. button 29. SLEEP button

Under teletext mode, press to disable teletext display and press again to resume.

17. button

Under teletext mode, press to display index page (always page 100).

18. button

Under teletext mode, press once to display the concealed information, such as solution of riddles or puzzles; press again to resume the riddles information from the display.

19. VGA button

Press to shift to VGA mode.

20. COMPONENT button

Press to shift to COMPONENT mode.

21. DISPLAY button

Press to display the reference information of the current program.

22. SET FAV button

Press to set the current channel as the favorite channel.

23. buttons

When in TV mode, press to return to the channel previously viewed.

24. FAV button

Press to set the current channel as favorite program.

25. SCAN button

When in TV mode, press to scan the programs and press again to stop scanning.

26.

CH +/- button

When in TV mode, press to select channel.

27. ASPECT button

Press to shift the aspect ratio of the screen between “Fill Screen” and “Aspect

Normal”.

28. MENU button

Press to enter or exit the setup menu.

This feature allows you to set up sleep time when in TV mode. Press the button and then press the ENTER button to activate this function. Then press the ▲▼ direction buttons to select the desired time to sleep.

30. button

Under teletext mode, press to freeze the current page and press again to resume.

31. button

Under teletext mode, press the button first time to double the size of teletext letters in the upper half of the screen, second to double the size of teletext letters in the lower half of the screen and third to resume normal status.

32. button

Under teletext mode, press to select four groups 3-digit numbers that displayed in different colors at the bottom of the screen.

Press the color buttons on the remote control to select, then use the number buttons to input the corresponding number to display the page.

Repeat the above procedures for each page to be stored, using a different color button accordingly each time.

33.

button

Under TV mode, press to display the realclock and press the EXIT button to exit.

- 7 -

Remote Control

Preparation of Remote Control

Softly push the back cover to open the battery compartment.

Insert two batteries (1.5V, size AAA), please make sure the polarity matches the marks inside the compartment.

Softly press the back cover to close it. z

Under normal use the battery will last for z six months.

Take out battery when the remote is not in use for a long time.

Using of Remote control

Point the remote control unit from no more than about 7m from the remote control sensor and within about 60 degrees of the front of the unit.

• The operating distance may vary depending to the brightness around.

NOTE:

• Do not point bright lights directly at the remote control sensor.

• Do not place objects between the remote control unit and the remote control sensor.

• Do not use this remote control unit while simultaneously operating the remote control unit of any other equipment.

- 8 -

System Connections

• Do not connect the power cord until all other connections have been made.

• Ensure that you observe the color cord when connecting audio and video cables.

Connecting to Power Supply

Power is supplied through the provided appropriative power adapter, one end is connected to the

DC 12V IN jack on the side panel of the unit, the other end to the wall AC outlet.

Connecting to External AV Input Device （ AV Output ）

Use the audio and video cable to connect the AV output jacks on the side panel of the unit to the external AV input device.

Note: The unit can only output TV, CVBS and S-VIDEO signals.

After connection, turn on the power of the unit and external AV input device and then press the

SOURCE button to shift to the corresponding mode.

- 9 -

System Connections

Connecting to External AV Signal Source

Use the audio and video cable to connect the AV input jacks on the rear panel of the unit to the external AV signal source. Use the S-VIDEO cable to connect the S-VIDEO input jack on the rear panel of the unit to the external AV signal source.

After connection, turn on the power of the unit and the external AV signal source and then press the

SOURCE button to shift to CVBS or S-VIDEO mode.

Note: the L/R audio input jacks can be used in the both CVBS and S-VIDEO modes.

Connecting to External AV Signal Source （ YPbPr ）

Use the audio and video cables to connect the Y/Pb/Pr input Jacks on the rear panel of the unit to the external AV signal source.

After connection, turn on the power of the unit and external AV signal source and then press the

SOURCE button to shift to COMPONENT mode.

- 10 -

System Connections

Connecting to Earphones

This unit can be connected to an earphone for listening music privately. See the below figure for derails:

◆ when the headphone is connected, the speakers will turn off automatically.

NOTE:

Excessively loud volume could damage your hearing. So turn down the volume before you connect the headphones, and then raise the volume to comfortable level.

- 11 -

System Connections

Connecting to PC

The unit can be connected to PC (person computer) via the VGA cable. Follow the steps and the figure below to connect:

1. Connect one end of the VGA cable to the VGA input jack on the rear panel of the unit.

2. Connect the other end to the PC.

3. Connect one end of the audio cable to the PC audio input jack on the rear panel of the unit.

4. Connect the other end to the PC audio output jack.

5. Please set the PC’s resolution at 1024x768@60Hz

After connection, turn on the unit and the PC and then press the SOURCE button to shift to VGA mode.

- 12 -

System Connections

Connecting to TV Antenna

This unit can be connected to the TV signal input source via the TV jack on the rear panel.

After connection, turn on the power of the unit. Then press the SOURCE button to shift to TV mode.

After connecting to the antenna, turn on the unit, and go on with program searching, you can follow the below steps to select channels:

1. For 0~9 channel:

Press the number buttons to select the channel X, wait several seconds and it will go to the selected channel.

Or press the number buttons to select channel X, and press the ENTER button to go to the selected channel immediately.

Or press the number buttons to select channel 0X, and it will go to the selected channel immediately.

2. For 10~99 channel:

Press the number buttons to select channel XX, and it will go to the selected channel immediately.

* X is the channel number.

- 13 -

TV Function

Preparations

1. After connection, press the POWER button to turn on the power. (If it is turned on, the power indicator is blue.)

2. Press the SOURCE button to shift to TV mode. You can go on with the following operations:

Image Setting

Note: This item is only available when there is signal input.

Press the MENU button once to enter the setup menu. Press the ▲▼ button to select Image and press the ENTER button to enter the menu shown on the right.

In the Image setup menu, press the ▲▼ button to select the desired item. Press the MENU button to return to the previous menu.

Picture Setup

Press the ▲▼ button to select Picture and press the ENTER button to enter. Press the

▲▼ button to select the desired item and press the ENTER button to confirm your selection.

Press the MENU button to return to the previous menu.

Scheme Setup

Press the ▲▼ button to select Scheme and press the ENTER button to enter. Press the

▲▼ button to select the desired item and press the ENTER button to confirm your selection.

Press the MENU button to return to the previous menu.

- 14 -

TV Function

Brightness Setup

Press the ▲▼ button to select

Brightness and press the ◄► button to adjust the value. Press the MENU button to return to the previous menu.

Contrast Setup

Press the ▲▼ button to select Contrast and press the ◄► button to adjust the value. Press the

MENU button to return to the previous menu.

Hue Setup

Press the ▲▼ button to select Hue and press the ◄► button to adjust the value. Press the MENU button to return to the previous menu.

Note: This item is only available under NTSC TV signal mode.

Saturation Setup

Press the ▲▼ button to select Saturation and press the ◄► button to adjust the value. Press the

MENU button to return to the previous menu.

Sharpness Setup

Press the ▲▼ button to select Sharpness and press the ◄► button to adjust the value. Press the

MENU button to return to the previous menu.

Advanced Setup

Press the ▲▼ button to select Advanced and press the ENTER button to enter.

In the menu, press the ▲▼◄► direction button to move the image. Press the MENU button to return to the previous menu.

Note: This item is only available in VGA and Component modes.

- 15 -

TV Function

Audio Setting

Press the MENU button once to enter the setup menu. Press the ▲▼ button to select Audio and press the ENTER button to enter the menu shown on the right.

In the Audio setup menu, press the ▲▼ button to select the desired item. Press the MENU button to return to the previous menu.

Volume Setup

Press the ▲▼ button to select Volume and press the ◄► button to adjust the level. Press the

MENU button to return to the previous menu.

Bass Setup

Press the ▲▼ button to select Bass and press the ◄► button to adjust the level. Press the MENU button to return to the previous menu.

Treble Setup

Press the ▲▼ button to select Treble and press the ◄► button to adjust the level. Press the

MENU button to return to the previous menu.

Balance Setup

Press the ▲▼ button to select Balance and press the ◄► button to adjust the level. Press the

MENU button to return to the previous menu.

Auto Volume Setup

Press the ▲▼ button to select Auto Volume and press the ENTER button to access the menu.

Press the ▲▼ button to select “On” or “Off” and press the ENTER button to confirm. Press the

MENU button to return to the previous menu.

Sound Mode Setup

Press the ▲▼ button to select Sound Mode and press the ENTER button to enter. Press the ▲▼ button to select the desired item and then press the ENTER button to confirm your selection. Press the MENU button to return to the previous menu.

- 16 -

TV Function

Timer Setting

Press the MENU button once to enter the setup menu. Press the ▲▼ button to select Timer and press the ENTER button to enter the menu shown on the right.

In the Timer setup menu, press the ▲▼ button to select Off, 15Min, 30Min, 45Min, 60Min,

75Min, 90Min, 105Min or 120Min. Press the

MENU button to return to the previous menu

Setup Setting

Press the MENU button once to enter the setup menu. Press the ▲▼ button to select Setup and press the ENTER button to enter the menu shown on the right.

In the Setup menu, press the ▲▼ button to select the desired item. Press the MENU button to return to the previous menu.

Tuner/Channel

Press the ▲▼ button to select the

Tuner/Channel and press the ENTER button to enter the menu shown on the right. Press the ▲▼ button to select the desired item. Press the MENU button to return to the previous menu.

- 17 -

TV Function

Country

Press the ▲▼ button to select the Country and press the

ENTER button to enter the menu shown on the right. Press the

▲▼ button to select the desired item. Press the MENU button to return to the previous menu.

Auto Scan

Press the ▲▼ button to select the Auto Scan and press the ENTER button to start auto scan. The screen will display shown below:

Auto scan will take a few minutes, when the tuning operation completes the unit will exit and memorize the programs by sequence automatically.

During tuning, press the MENU button to exit the auto scan mode.

Prog Organizer

Press the ▲▼ button to select the

Prog Organizer and press the

ENTER button to enter the menu shown on the right.

In the Prog Organizer setup menu, press the ▲▼ button to select the desired item. Press the MENU button to return to the previous menu.

- 18 -

TV Function

Channel Name

Press the ▲▼ button to select the Channel Name and press the ENTER button to enter. Then press the ▲▼ button to select letters or press the number button to input numbers. Press the

MENU button to return to the previous menu.

Skip

Press the ▲▼ button to select Skip and press the ENTER button to activate or cancel this function.

Press the MENU button to return to the previous menu.

Swap

Press the ▲▼ button to select Swap from Ch and press the ENTER button to enter. Press the number buttons to select program number. Repeat the above operations to Swap To Ch . Then

Press the ▲▼ button to select Perform Swap and press the ENTER button to confirm.

Manual Install

Press the ▲▼ button to select the

Manual Install and press the

ENTER button to enter the menu shown on the right.

In the Manual Install setup menu, press the desired item. Press the MENU button to return to the previous menu.

▲▼ button to select the

Search

Press the ▲▼ button to select Search and press the ► or ◄ to start searching forward or backward. Press the MENU button to return to the previous menu.

Color System

Press the ▲▼ button to select Color System and press the ENTER button to enter. Press the

MENU button to return to the previous menu.

Fine Tune

Press the ▲▼ button to select Fine Tune and press the ENTER button to enter. Press the ► or ◄ controls to start fine tuning forward or backward. Press the MENU button to return to the previous menu.

This feature allows for minor adjustments to the integrated electronic tuner’s ability to tune in weak broadcast signals or where applicable solve minor irregularities in cable channel tuning parameters.

- 19 -

TV Function

CH NO

Press the ▲▼ button to select CH NO and press the ENTER button to enter. Press the number buttons to enter the channel number. Press the MENU button to return to the previous menu.

Store

Press the ▲▼ button to select Store and press the ENTER button to store the above operations.

Note: The “CH NO” and “Store” items only function when the program is searched out.

Language

Press the ▲▼ button to select the

Language , press the ENTER button to enter the setup, press the ▲▼ button to select item. Press the MENU button to return to the previous menu.

Factory Reset

Press the ▲▼ button to select the Factory Reset and press the ENTER button to enter. Press the

▲▼ button to select “Yes” or “No” and press the ENTER button to confirm. Press the MENU button to return to the previous menu.

- 20 -

NICAM Function

The unit support NICAM function under TV mode.

Under NICAM TV broadcast:

1. When receiving stereo audio signals, press the STEREO/AUDIO button on the remote control repeatedly to shift the sound tracks between Nicam Stereo and Mono and the screen will appear corresponding display as shown below:

2. When receiving bilingual audio signals, press the STEREO/AUDIO button on the remote control repeatedly to shift the sound tracks among Nicam I, Nicam II, Nicam I+II and Mono and the screen will appear corresponding display as shown below:

3.

When receiving mono audio signals, press the STEREO/AUDIO button on the remote control repeatedly to shift the sound tracks between Nicam Mono and Mono and the screen will appear corresponding display as shown below:

Under A2 TV broadcast:

1. When receiving stereo audio signals, press the STEREO/AUDIO button on the remote control repeatedly to shift the sound tracks between Stereo and Mono and the screen will appear corresponding display as shown below:

2.

When receiving bilingual audio signals, press the STEREO/AUDIO button on the remote control repeatedly to shift the sound tracks among I, II and I+II and the screen will appear corresponding display as shown below:

3.

When receiving mono audio signals, press the STEREO/AUDIO button on the remote control to display sound track Mono on the screen.

- 21 -

Other Functions

External AV Input Function

The unit has external AV input function. It supports CVBS, S-VIDEO and Component modes. Use the audio, video and S-Video cable to connect the unit to the external AV signal source such as recorder, vidicon, satellite receiver or game player etc. Then turn on the unit and the external AV signal source. Press the SOURCE button to shift to the corresponding mode. Then you can go on to set up the menu in a certain mode.

Computer Screen Function

The TFT LCD screen of the unit can be used as the computer screen. Take the steps of connecting the unit to the PC and then you can set up the menu.

You had better set the PC’s resolution at: 1280 x 768@60Hz.

The operations of these menus in CVBS, S-VIDEO, Component and VGA modes are the same with those in the TV mode. Please refer to the introduction in “TV Function”.

Note:

1. Only when there are signals, the menus can appear and be set.

2. Some of these menus are not available in these modes.

- 22 -

Troubleshooting

There is no sound.

LCD is no display

Make sure system connection is correct.

Make sure the speakers are not muted.

In TV mode, set the correct sound mode.

Make sure the unit is turned on and the connections are correct.

Make sure the power adapter is correctly connected.

There is no picture or picture move up and down unsteady.

Check if the connections with the external AV signal source are correct.

Correctly set the items in the picture menu.

Check if the video type input signal is not corresponding to the unit.

Make sure the unit is turned on and in correct video type.

The remote control does not work.

Make sure there are no obstructions between the remote control and the player.

Make sure the remote control is pointing at the player.

Make sure batteries are inserted and the polarity is correct.

Make sure battery is not weak.

Other Notes:

Static or other external interfere may cause the unit to behave abnormally. In this occurs, unplug the power-supply cord from the outlet and plug it in again to reset the unit. If the problems persist, then please disconnect the power and consult a qualified technician.

- 23 -

Specifications

TFT-LCD Resolution 1440 x 900

TFT-LCD Screen Size 19 inches

Power

Power Consumption

AC100 ～ 240V ， 50/60Hz

DC 12V

< 60W

Dimension

Weight

494mm × 184mm × 412mm （ LXWXD ）

About 7.8 Kg

Ambient Temperature 10~45 ℃

DESIGN AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

- 24 -

- 1 -