Stanley Black & Decker | CS06 | CS05-06 User Manual 7-2014 V8

CS05/CS06

HYDRAULIC

CHAIN SAW

USER MANUAL

Safety, Operation and Maintenance

© 2014 Stanley Black & Decker, Inc.

New Britain, CT 06053

U.S.A.

66864 7/2014 Ver. 8

TABLE OF CONTENTS

SAFETY SYMBOLS ..................................................................................................................................................4

SAFETY PRECAUTIONS ..........................................................................................................................................5

ELECTRICAL PRECAUTIONS .................................................................................................................................7

TOOL STICKERS & TAGS ........................................................................................................................................9

HOSE TYPES ..........................................................................................................................................................10

HOSE RECOMMENDATIONS ................................................................................................................................ 11

FIGURE 1. TYPICAL HOSE CONNECTIONS ..................................................................................................... 11

HTMA REQUIREMENTS .........................................................................................................................................12

OPERATION ............................................................................................................................................................13

FIGURE 2. FELLING A TREE ..............................................................................................................................14

FIGURE 3. CROSSCUTTING LOGS WITH PRESSURE ON TOP .....................................................................15

FIGURE 4. CROSSCUTTING LOGS LARGER THAN BAR LENGTH WITH PRESSURE ON TOP ...................15

FIGURE 5. CROSSCUTTING LOGS/LIMBS WITH PRESSURE ON BOTTOM. ................................................16

FIGURE 6. CROSSCUTTING THICK LOGS WITH PRESSURE ON BOTTOM .................................................16

TOOL PROTECTION & CARE ................................................................................................................................18

TROUBLESHOOTING ............................................................................................................................................19

SPECIFICATIONS ...................................................................................................................................................20

ACCESSORIES.......................................................................................................................................................20

SERVICE TOOLS ....................................................................................................................................................20

CS05/CS06 PARTS ILLUSTRATION ......................................................................................................................21

CS05/CS06 PARTS LIST ........................................................................................................................................22

UNDERWATER TOOLS DEPTH GUIDELINE .........................................................................................................24

IMPORTANT

To fill out a Product Warranty Recording form, and for information on your warranty, visit Stanleyhydraulics.com and select the Company tab, Warranty.

( NOTE: The warranty recording form must be submitted to validate the warranty).

SERVICING: This manual contains safety, operation, and routine maintenance instructions. Stanley Hydraulic Tools recommends that servicing of hydraulic tools, other than routine maintenance, be performed by an authorized and certified dealer. Please read the following warning.

WARNING

SERIOUS INJURY OR DEATH COULD RESULT FROM

THE IMPROPER REPAIR OR SERVICE OF THIS TOOL.

REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE

DONE BY AN AUTHORIZED AND CERTIFIED DEALER.

For the nearest authorized and certified dealer, call Stanley Hydraulic Tools at the number listed on the back of this manual and ask for a Customer Service Representative.

CS05/CS06 User Manual ◄ 3

SAFETY SYMBOLS

Safety symbols and signal words, as shown below, are used to emphasize all operator, maintenance and repair actions which, if not strictly followed, could result in a life-threatening situation, bodily injury or damage to equipment.

DANGER

WARNING

CAUTION

CAUTION

NOTICE

IMPORTANT

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

This safety alert and signal word indicate an imminently hazardous situation which, if not avoided, will result in death or serious injury.

This safety alert and signal word indicate a potentially hazardous situation which, if not avoided, could result in death or serious injury.

This safety alert and signal word indicate a potentially hazardous situation which, if not avoided, could result in death or serious injury.

This signal word indicates a potentially hazardous situation which, if not avoided, may result in property damage.

This signal word indicates a situation which, if not avoided, will result in damage to the equipment.

This signal word indicates a situation which, if not avoided, may result in damage to the equipment.

Always observe safety symbols. They are included for your safety and for the protection of the tool.

LOCAL SAFETY REGULATIONS

Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and maintenance personnel.

4 ► CS05/CS06 User Manual

SAFETY PRECAUTIONS

Tool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose.

These safety precautions are given for your safety. Review them carefully before operating the tool and before performing general maintenance or repairs.

Supervising personnel should develop additional precautions relating to the specific work area and local safety regulations. If so, place the added precautions in the space provided in this manual.

The model CS05/CS06 Hydraulic Chain Saw will provide safe and dependable service if operated in accordance with the instructions given in this manual. Read and understand this manual and any stickers and tags attached to the tool and hose before operation. Failure to do so could result in personal injury or equipment damage.

• The operator must start in a work area without bystanders. Flying debris can cause serious injury.

• Do not operate the tool unless thoroughly trained or under the supervision of an instructor. Establish a training program for all operators to ensure safe operation.

• Always wear safety equipment such as goggles, ear and head protection, and safety shoes at all times when operating the tool. Use gloves and aprons when necessary.

• The operator must be familiar with all prohibited work areas such as excessive slopes and dangerous terrain conditions.

• Do not inspect, clean or replace any part(s) if the hydraulic power source is connected. Do not inspect or clean the tool while the hydraulic power source is connected. Accidental engagement of the tool can cause serious injury.

• Always connect hoses to the tool hose couplers before energizing the hydraulic power source. Be sure all hose connections are tight and are in good condition.

• Do not operate the tool at oil temperatures above

140 °F/60 °C. Operation at higher temperatures can cause higher than normal temperatures at the tool which can result in operator discomfort.

• Do not operate a damaged, improperly adjusted, or incompletely assembled chain saw. Be sure that the chain stops moving when the control trigger is released.

• Never wear loose clothing that can get entangled in the working parts of the tool.

• Keep all parts of your body away from the chain saw and maintain proper footing and balance at all times.

• Warning: Use of this tool on certain materials during demolition could generate dust potentially containing a variety of hazardous substances such as asbestos, silica or lead. Inhalation of dust containing these or other hazardous substances could result in serious injury, cancer or death. Protect yourself and those around you. Research and understand the materials you are cutting. Follow correct safety procedures and comply with all applicable national, state or provisional health and safety regulations relating to them, including, if appropriate arranging for the safe disposal of the materials by a qualified person.

• Do not rely exclusively upon the safety devices built into the saw. As a chain saw user, several steps must be taken to keep your cutting jobs free from accidents or injury.

– With basic understanding of kickback, you can reduce or eliminate the element of surprise.

Sudden surprise contributes to accidents.

– To avoid personal injury or equipment damage, all tool repair, maintenance and service must only be performed by authorized and properly trained personnel.

– Keep a good firm grip on the saw with both hands, the right hand on the rear handle and the left hand on the front handle when operating the saw. Use a firm grip with thumbs and fingers encircling the chain saw handles. A firm grip will help reduce kickback and maintain control of the saw. Do not let go.

– Make sure the area in which you are cutting is free of obstructions. Never allow the nose of the guide bar to contact the log, branch or any obstruction that can be accidently hit while operating the saw.

– Never start the tool while it is lying on the ground.

– Cut at rated operating speeds (gpm).

– Do not overreach or cut above shoulder height.

– Follow the manufacturer’s sharpening and


SAFETY PRECAUTIONS

– maintenance instructions for the saw chain.

– Only use replacement bars and chains specified by Stanley Hydraulic Tools. Chains must meet the requirements of ANSI B175.1 for low kickback performance.

• Always be well rested and mentally alert before operating the chain saw.

• Do not allow other persons to be near the chain saw when starting or cutting with the chain saw. Keep bystanders and animals out of the work area.

• Do not starting cutting until you have a clear work area, secure footing and a planned escape path from a falling tree.

• Carry the saw with the unit de-energized and the bar and chain to the rear of your body.

• Use extreme caution when cutting small size brush and saplings. Twigs may catch the saw chain and be whipped toward the operator or pull the operator off balance.

• When cutting a limb that is under tension, be alert for springback so that you will not be struck when the tension on the limb is released.

• Keep the handles dry, clean and free of oil.

• Do not operate a chain saw while in a tree unless you have been specially trained to do so.

• When using tools near energized transmission lines, be sure to use only hoses labeled and certified nonconductive.

• Turn off the power unit or move the hydraulic control valve to neutral before setting the saw down.

• Use a guide bar scabbard when transporting the saw.

• Know the location of buried or covered electrical services before starting work.

• To avoid personal injury or equipment damage, all tool repair, maintenance and service must only be performed by authorized and properly trained personnel.


ELECTRICAL PRECAUTIONS

The following guidelines must be followed to prevent accidental contact with overhead electrical conductors and/or communication wires and cables. (ref. ANSI

Z133.1-2000)

Working in Proximity to Electrical Hazards:

An inspection shall be made by a qualified arborist to determine whether an electrical hazard exists before climbing, or otherwise entering, or performing work in or on a tree.

Only qualified line-clearance arborists or qualified lineclearance arborist trainees shall be assigned to work where an electrical hazard exists. Qualified line-clearance arborist trainees shall be under the direct supervision of qualified line-clearance arborist.

A second qualified line-clearance arborists or line-clearance arborist trainees shall be within vision or voice communication during line-clearing operations aloft when line-clearance arborists or line-clearance arborist trainees must approach closer than 10 feet (3.05 meters) to any energized electrical conductor in excess of

750 volts (primary conductor) or when:

1. Branches or limbs being removed cannot first be cut (with a pole pruner/pole saw) to sufficiently clear electrical conductors, so as to avoid contact.

2. Roping is required to remove branches or limbs from such electrical conductors. This does not apply to individuals working on behalf of, or employed by, electrical system owners/operators engaged in line-clearing operations incidental to their normal occupation.

Qualified line-clearance arborists and line-clearance arborist trainees shall maintain minimum approach distances from energized electrical conductors in accordance with Table 1.

All other arborists shall maintain a minimum approach distance from energized electrical conductors in accordance with Table 2.

Branches hanging on an energized electrical conductor shall be removed using non-conductive equipment.

Table 1 – Minimum approach distances from energized conductors for qualified line-clearance arborists and qualified line- clearance arborist trainees.

Nominal Voltage

(kV phase-to-phase)

0.05 to 1.0

1.1 to 15.0

15.1 to 36.0

36.1 to 46.0

46.1 to 72.5

72.6 to 121.0

138.0 to 145.0

161.0 to 169.0

230.0 to 242.0

345.0 to 362.0

500.0 to 550.0

Includes 1910.269

elevation factor, sea level to 5000 ft

1

ft–in

Avoid contact

2–04

2–09

3–00

3–09

4–06

5–02

6–00

7–11

13–02

19–00

m

0.71

0.84

0.92

1.14

1.37

1.58

1.83

2.41

4.02

5.80

Includes 1910.269

elevation factor,

5001 – 10,000 ft

ft–in

Avoid contact

2–08

3–02

3–05

4–03

5–02

5–11

6–10

9–00

15–00

21–09

765.0 to 800.0

27–04 8.34

31–03

1

Exceeds phase-to-ground; elevation factor per 29 CFR 1910.269.

m

1

0.81

0.97

1.04

1.30

1.58

1.80

2.08

2.75

4.58

6.63

9.53

Includes 1910.269 elevation

factor, 10,000 – 14,000 ft

1

ft–in

Avoid contact

m

2–10

3–05

3–09

4–07

5–07

6–05

7–05

9–09

16–03

23–06

33–10

0.86

1.04

1.14

1.40

1.70

1.96

2.26

2.97

4.96

7.17

10.32


ELECTRICAL PRECAUTIONS

Table 2 – Minimum approach distances to energized conductors for persons other than qualified line-clearance arborists and qualified line-clearance arborist trainees.

Nominal Voltage

kV phase-to-phase

0.0 to 1.0

1.1 to 15.0

15.1 to 36.0

36.1 to 50.0

50.1 to 72.5

72.6 to 121.0

138.0 to 145.0

161.0 to 169.0

230.0 to 242.0

345.0 to 362.0

500.0 to 550.0

785.0 to 800.0

1

1

Exceeds phase-to-ground.

ft-in

10–00

10–00

10–00

10–00

10–09

12–04

13–02

14–00

16–05

20–05

26–08

35–00

Distance

4.00

4.24

4.97

6.17

8.05

10.55

m

3.05

3.05

3.05

3.05

3.28

3.76

The tie-in position should be above the work area and located in such a way that a slip would swing the arborist away from any energized electrical conductors or other identified hazard.

While climbing, the arborist should climb on the side of the tree that is away from energized electrical conductors as required in Tables 1 and 2.

Footwear, including lineman’s overshoes, having electrical-resistant soles, shall not be considered as providing any measure of safety from electrical hazards.

Rubber gloves, with or without leather or other protective covering, shall not be considered as providing any measure of safety from electrical hazards.

Ladders, platforms and aerial devices, including insulated aerial devices, shall be subject to minimum approach distances in Table 1 and 2.

Aerial devices and attached equipment (such as chippers) contacting energized electrical conductors shall be considered energized. Contact shall be avoided, except where emergency rescue procedures are being carried out. Emergency rescue should be performed in accordance with 4.3.

STORM WORK AND EMERGENCY

CONDITIONS-LINE CLEARANCE

Line clearance shall not be performed during adverse weather conditions such as thunderstorms, high winds and snow and ice storms.

Qualified line-clearance arborists and qualified lineclearance arborists trainees performing line clearance in the aftermath of a storm or under similar conditions shall be trained in the special hazards associated with this type of work.

Line-clearance operations shall be suspended when storm work or emergency conditions develop involving energized electrical conductors. Electrical system owners/operators shall be notified immediately.


TOOL STICKERS & TAGS

DANGER

Failure to use hydraulic hose labeled and certified as non-conductive when using hydraulic tools on or near electric lines may result in death or serious injury.

ELECTROCUTION

HAZARD

For proper and safe operation read owners manual and mwke sure that you have been properly trained in correct procedures required for work on or around electric lines.

12412

Electrical Warning Decal

28409

Composite Decal

(CE Models Only)

D

30 LPM @ 138 B AR

EHTMA CATEGORY

11207

Circuit Type D Decal

(CE Models Only)

Lwa

107

17784

101 Sound Level

Decal

(CE Models Only)

28323

CE Decal

(CE Models Only)

4-6 GPM / 15-22 LPM

DO NOT EXCEED 2000 PSI / 140 BAR

DO NOT EXCEED SPECIFIED FLOW OR PRESSURE

USE CLOSED-CENTER TOOL ON CLOSED-CENTER

SYSTEM. USE OPEN-CENTER TOOL ON OPEN-CENTER

SYSTEM. CORRECTLY CONNECT HOSES TO TOOL “IN”

AND “OUT” PORTS. IMPROPER HANDLING, USE OR OTHER

MAINTENANCE OF TOOL COULD RESULT IN A LEAK, BURST

OR OTHER TOOL FAILURE. CONTACT AT A LEAK OR BURST

CAN CAUSE OIL INJECTION INTO THE BODY. FAILURE TO

OBSERVE THESE PRECAUTIONS CAN RESULT IN SERIOUS

PERSONAL INJURY.

03782

GPM Decal – CS05 Model

03786

GPM Decal – CS06 Model (Not Shown)

13907

Kickback Warning Decal

Stanley Hydraulic Tools

3810 SE Naef Road

Milwaukie, OR 97062

Model

07636

Name Tag

THIS CHAIN SAW IS

EQUIPPED WITH AN

AUTOMATIC CHAIN

OILER.

SEE YOUR PARTS &

SERVICE BOOK FOR

PROPER ADJUSTING

PROCEDURES

04746

Auto Oiler Decal

D A N G E R

1. FAILURE TO USE HYDRAULIC HOSE LABELED AND CERTI-

FIED AS NON-CONDUCTIVE WHEN USING HYDRAULIC

TOOLS ON OR NEAR ELECTRICAL LINES MAY RESULT IN

DEATH OR SERIOUS INJURY.

BEFORE USING HOSE

LABELED AND CERTIFIED AS NON-

CONDUCTIVE ON OR NEAR ELECTRIC LINES BE SURE THE

HOSE IS MAINTAINED AS NON-CONDUCTIVE. THE HOSE

SHOULD BE REGULARLY TESTED FOR ELECTRIC CURRENT

LEAKAGE IN ACCORDANCE WITH YOUR SAFETY DEPART-

MENT INSTRUCTIONS.

2. A HYDRAULIC LEAK OR BURST MAY CAUSE OIL INJECTION

INTO THE BODY OR CAUSE OTHER SEVERE PERSONAL

INJURY.

A. DO NOT EXCEED SPECIFIED FLOW AND PRESSURE

FOR THIS TOOL. EXCESS FLOW OR PRESSURE MAY

CAUSE A LEAK OR BURST.

B. DO NOT EXCEED RATED WORKING PRESSURE OF

HYDRAULIC HOSE USED WITH THIS TOOL. EXCESS

PRESSURE MAY CAUSE A LEAK OR BURST.

C. CHECK TOOL HOSE COUPLERS AND CONNECTORS

DAILY FOR LEAKS. DO NOT FEEL FOR LEAKS WITH

YOUR HANDS. CONTACT WITH A LEAK MAY RESULT

IN SEVERE PERSONAL INJURY.

D A N G E R

D. DO NOT LIFT OR CARRY TOOL BY THE HOSES. DO

NOT ABUSE HOSE. DO NOT USE KINKED, TORN OR

DAMAGED HOSE.

3. MAKE SURE HYDRAULIC HOSES ARE PROPERLY CON-

NECTED TO THE TOOL BEFORE PRESSURING SYSTEM.

SYSTEM PRESSURE HOSE MUST ALWAYS BE CON-

NECTED TO TOOL “IN” PORT. SYSTEM RETURN HOSE

MUST ALWAYS BE CONNECTED TO TOOL “OUT” PORT.

REVERSING CONNECTIONS MAY CAUSE REVERSE

TOOL OPERATION WHICH CAN RESULT IN SEVERE

PERSONAL INJURY.

4. DO NOT CONNECT OPEN-CENTER TOOLS TO CLOSED-

CENTER HYDRAULIC SYSTEMS. THIS MAY RESULT IN

LOSS OF OTHER HYDRAULIC FUNCTIONS POWERED BY

THE SAME SYSTEM AND/OR SEVERE PERSONAL INJURY.

5. BYSTANDERS MAY BE INJURED IN YOUR WORK AREA.

KEEP BYSTANDERS CLEAR OF YOUR WORK AREA.

6. WEAR HEARING, EYE, FOOT, HAND AND HEAD PRO-

TECTION.

7. TO AVOID PERSONAL INJURY OR EQUIPMENT DAMAGE,

ALL TOOL REPAIR MAINTENANCE AND SERVICE MUST

ONLY BE PERFORMED BY AUTHORIZED AND PROPERLY

TRAINED PERSONNEL.

NOTE

THE INFORMATION LISTED ON THE

STICKERS SHOWN, MUST BE LEGIBLE AT ALL

TIMES.

I M P O R T A N T I M P O R T A N T

REPLACE DECALS IF THEY BECOME WORN

OR DAMAGED. REPLACEMENTS ARE

AVAILABLE FROM YOUR LOCAL STANLEY

DISTRIBUTOR.

The safety tag (P/N 15875) at right is attached to the tool when shipped from the factory. Read and understand the safety instructions listed on this tag before removal. We suggest you retain this tag and attach it to the tool when not in use.

SAFETY INSTRUCTIONS FOR THIS

TOOL BEFORE USING IT.

PROCEDURES APPROVED BY

STANLEY AND DESCRIBED IN THE

OPERATION MANUAL.

TAG TO BE REMOVED ONLY BY

TOOL OPERATOR.

SEE OTHER SIDE

SAFETY INSTRUCTIONS FOR THIS

TOOL BEFORE USING IT.

PROCEDURES APPROVED BY

STANLEY AND DESCRIBED IN THE

OPERATION MANUAL.

TAG TO BE REMOVED ONLY BY

TOOL OPERATOR.

SEE OTHER SIDE

SAFETY TAG P/N 15875 (Shown smaller then actual size)


HOSE TYPES

The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hydraulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with

Stanley Hydraulic Tools. They are:

Certified non-conductive — constructed of thermoplastic or synthetic rubber inner tube, synthetic fiber braid reinforcement, and weather resistant thermoplastic or synthetic rubber cover. Hose labeled

certified non-

conductive is the only hose authorized for use near electrical conductors.

Wire-braided (conductive) — constructed of synthetic rubber inner tube, single or double wire braid reinforcement, and weather resistant synthetic rubber cover. This hose is

conductive and must never be used near electrical conductors.

Fabric-braided (not certified or labeled non-conductive) — constructed of thermoplastic or synthetic rubber inner tube, synthetic fiber braid reinforcement, and weather resistant thermoplastic or synthetic rubber cover. This

hose is not certified non-conductive and must never be used near electrical conductors.

HOSE SAFETY TAGS

To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic

Tools. DO NOT REMOVE THESE TAGS.

If the information on a tag is illegible because of wear or damage, replace the tag immediately. A new tag may be obtained from your Stanley Distributor.

THE TAG SHOWN BELOW IS ATTACHED TO “CERTIFIED NON-CONDUCTIVE” HOSE

D A N G E R

1. FAILURE TO USE HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE

WHEN USING HYDRAULIC TOOLS ON OR NEAR ELECTRIC LINES MAY RESULT IN

DEATH OR SERIOUS INJURY.

FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROP-

ERLY TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND

ELECTRIC LINES.

2. BEFORE USING HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE

ON OR NEAR ELECTRIC LINES. WIPE THE ENTIRE LENGTH OF THE HOSE AND FIT-

TING WITH A CLEAN DRY ABSORBENT CLOTH TO REMOVE DIRT AND MOISTURE AND

TEST HOSE FOR MAXIMUM ALLOWABLE CURRENT LEAKAGE IN ACCORDANCE WITH

SAFETY DEPARTMENT INSTRUCTIONS.

3.

SEE OTHER SIDE

DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE

OR HANDLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE.

KEEP HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT

CONTACT DURING USE. CONTACT AT THE BURST CAN CAUSE BODILY INJECTION

AND SEVERE PERSONAL INJURY.

4. HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, ABRASION, CUTTING, OR

CONTACT WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT

USE HOSE TO PULL OR LIFT TOOLS, POWER UNITS, ETC.

5. CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAM-

AGE TO COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE

IMMEDIATELY. NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.

6. AFTER EACH USE STORE IN A CLEAN DRY AREA.

SEE OTHER SIDE

SIDE 1 SIDE 2

(Shown smaller than actual size)

THE TAG SHOWN BELOW IS ATTACHED TO “CONDUCTIVE” HOSE.

D A N G E R

1. DO NOT USE THIS HYDRAULIC HOSE ON OR NEAR ELECTRIC LINES. THIS HOSE IS

NOT LABELED OR CERTIFIED AS NON-CONDUCTIVE. USING THIS HOSE ON OR NEAR

ELECTRICAL LINES MAY RESULT IN DEATH OR SERIOUS INJURY.

2. FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROPERLY

TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND ELEC-

TRIC LINES.

3. DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE OR HAN-

DLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE. KEEP HOSE AS FAR

AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT CONTACT DURING USE.

CONTACT AT THE BURST CAN CAUSE BODILY INJECTION AND SEVERE PERSONAL INJURY.

4. HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, CUTTING, OR CONTACT

WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT USE HOSE TO

PULL OR LIFT TOOLS, POWER UNITS, ETC.

SEE OTHER SIDE

SIDE 1

5. CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAMAGE TO

COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE IMMEDIATELY.

NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.

6. AFTER EACH USE STORE IN A CLEAN DRY AREA.

SEE OTHER SIDE

(Shown smaller than actual size)

SIDE 2


HOSE RECOMMENDATIONS

Tool to Hydraulic Circuit Hose Recommendations

All hydraulic hose must meet or exceed specifications as set forth by SAE J517.


HTMA / EHTMA REQUIREMENTS

HTMA / EHTMA REQUIREMENTS

HTMA

HYDRAULIC SYSTEM REQUIREMENTS

Flow Range

Nominal Operating Pressure

(at the power supply outlet)

TYPE I

4-6 gpm

(15-23 lpm)

1500 psi

(103 bar)

System relief valve setting


TOOL TYPE

TYPE II

7-9 gpm

(26-34 lpm)

1500 psi

(103 bar)

TYPE RR

9-10.5 gpm

(34-40 lpm)

1500 psi

(103 bar)

TYPE III

11-13 gpm

(42-49 lpm)

1500 psi

(103 bar)

2100-2250 psi 2100-2250 psi 2200-2300 psi 2100-2250 psi

(145-155 bar) (145-155 bar) (152-159 bar) (145-155 bar)

Maximum back pressure

(at tool end of the return hose)

Measured at a max. fluid viscosity of:

(at min. operating temperature)

250 psi

(17 bar)

250 psi

(17 bar)

250 psi

(17 bar)

250 psi

(17 bar)

400 ssu* 400 ssu* 400 ssu* 400 ssu*

(82 centistokes) (82 centistokes) (82 centistokes) (82 centistokes)

Temperature: Sufficient heat rejection

capacity to limit max. fluid temperature to:

(at max. expected ambient temperature)

140° F

(60° C)

140° F

(60° C)

140° F

(60° C)

140° F

(60° C)

Min. cooling capacity at a temperature

difference of between ambient and fluid

temps

NOTE:

Do not operate the tool at oil temperatures above 140° F (60° C). Operation at higher temperatures can cause operator

discomfort at the tool.

Filter

Min. full-flow filtration

Sized for flow of at least:

(For cold temp. startup and max.

dirt-holding capacity)

3 hp

(2.24 kW)

40° F

(22° C)

25 microns

30 gpm

(114 lpm)

5 hp

(3.73 kW)

40° F

(22° C)

25 microns

30 gpm

(114 lpm)

6 hp

(5.22 kW)

40° F

(22° C)

25 microns

30 gpm

(114 lpm)

7 hp

(4.47 kW)

40° F

(22° C)

25 microns

30 gpm

(114 lpm)

Hydraulic fluid Petroleum based

(premium grade, anti-wear, non-conductive)

100-400 ssu* 100-400 ssu*

Viscosity (at min. and max. operating temps)

(20-82 centistokes)

100-400 ssu* 100-400 ssu*

NOTE:

When choosing hydraulic fluid, the expected oil temperature extremes that will be experienced in service determine the

most suitable temperature viscosity characteristics. Hydraulic fluids with a viscosity index over 140 will meet the requirements

over a wide range of operating temperatures.

*SSU = Saybolt Seconds Universal

EHTMA

HYDRAULIC SYSTEM

REQUIREMENTS

B

C

CLASSIFICATION

D

Flow Range

Nominal Operating Pressure


System relief valve setting


3.5-4.3 gpm 4.7-5.8 gpm

(13.5-16.5 lpm) (18-22 lpm)

1870 psi

(129 bar)

1500 psi

(103 bar)

2495 psi

(172 bar)

2000 psi

(138 bar)

7.1-8.7 gpm

(27-33 lpm)

1500 psi

(103 bar)

2000 psi

(138 bar)

9.5-11.6 gpm

(36-44 lpm)

1500 psi

(103 bar)

2000 psi

(138 bar)

11.8-14.5 gpm

(45-55 lpm)

1500 psi

(103 bar)

2000 psi

(138 bar)

NOTE: These are general hydraulic system requirements. See tool specification page for tool specific requirements


OPERATION

PREOPERATION PROCEDURES

CHECK POWER SOURCE

1. Using a calibrated flowmeter and pressure gauge, check that the hydraulic power source develops a flow of 4-6 gpm/15-23 lpm at 1500-2000 psi/105-

140 bar for the CS05 or a flow of 7-9 gpm/26-34 lpm at 1000-2000 psi/70-140 bar for the CS06.

2. Make certain that the hydraulic power source is equipped with a relief valve set to open at 2100 -

2250 psi/145-155 bar.

CONNECT HOSES

1. Wipe all hose couplers with a clean lint-free cloth before making connections.

2. Connect the hoses from the hydraulic power source to the tool fittings or quick disconnects. It is good practice to connect return hoses first and disconnect them last to minimize or avoid trapped pressure within the tool.

3. Observe the arrow on the couplers to ensure that the flow is in the proper direction. The female coupler on the tool hose is the inlet (pressure) coupler.

4. Move the hydraulic circuit control valve to the “ON” position to operate the tool.

NOTE:

If uncoupled hoses are left in the sun, pressure increase inside the hose may make them difficult to connect. Whenever possible, connect the free ends of the hoses together.

SYSTEM SELECTION (OC/CC)

Saws configured with the system selector option require setup for the system, closed-center (CC) or open-center

(CC), in which it will operate. The selector screw is located in the bottom end of the valve spool.

1. Determine the system type.

2. For operation in a CC system, turn the selector screw fully clockwise. When the selector screw bottoms, CC operation is selected.

3. For operation in an OC system, turn the selector screw counter-clockwise until meeting resistance

(from the retaining ring). Turn the selector screw clockwise and then counter-clockwise to be sure that you are sensing resistance of the retaining ring.

Do not force the selector screw.

IMPORTANT

To prevent damage to the retaining ring, do not attempt to force the selector screw counter-clockwise beyond the point of initial resistance.

OPERATING PROCEDURES

The following are general wood cut ting procedures and techniques. Dif ferences in the terrain, vegetation, and type of wood will make this infor mation more or less valid for particu lar areas. For advice on specific woodcutting problems or techniques for your area, consult your local Stanley representative or your county agent. They can often provide infor mation that will make your work safer and more productive.

CUTTING TIPS

1. Check the lean of the tree. Tie a weight to a piece of string about 2 feet long. Hang the weight in your line of sight. The string is a good vertical line to help you judge the lean of the tree. The tree should fall the way it is leaning. Trees that are straight (leaning no more than 5 degrees) gener ally can be felled in any direction.

2. Avoid felling across another tree, log, rocks, gully or ridge. Do not fell straight uphill or down hill. Fell the tree diagonally to the hill. Consider the wind direction and velocity. Do not attempt cutting in strong winds.

3. Check the weight distribution. A tree is heavier on the side with the most limbs. It will try to fall on its heavy side. Trim a few limbs to “balance” the tree.

4. Clear the work area. You need a clean area all around the tree for good footing. Get every thing out of the area where the tree will fall. Do not cut trees near structures. Because of the danger of electrocution, use extreme care when cutting trees near power lines.

5. Before starting the cut, prepare your escape path.

Make sure the escape path is clear of brush and branches. The escape path should be at an angle away from the direction of fall.


OPERATION

6. The saw chain should cut with very little pres sure applied to the handle. If you have to force the saw to cut or if the cut is not straight, cease cutting immediately to prevent further saw chain and bar damage.

See the Maintenance and Adjustments section of the Service Manual for chain replacement or adjustment procedures.

7. Underwater models require daily preventive maintenance. See the Maintenance and Adjust ments section of the Service Manual for these mainte nance procedures.

FELLING (CUTTING DOWN A TREE)

(FIGURE 2)

Observe all safety precautions.

Figure 2. Felling a Tree

NOTCHING OR UNDERCUTTING

1. The notching or undercutting cut is made on the side you want the tree to fall. Place the saw so the hand guard is close to the tree trunk and the bucking cleat is dug in.

2. Start the cut horizontally. Pivot the nose of the bar in last. Cut to about one-quarter of the tree’s diameter.

WARNING

Watch out for falling limbs.

3. Make a diagonal cut down to meet the hori zontal cut and remove the wood from the notch.

FELLING OR BACK CUT

4. The felling or back cut is made on the side opposite and at least 2 inches above the hori zontal undercut

(the felling cut is made higher as the size of the tree increases). Place the saw so the hand guard is close to the tree trunk and the bucking cleat is dug in.

5. Start the cut horizontally. Pivot the bar in until the cut is being made parallel to the notch cut. Cut until the saw is about 1 or 2 inches from the notch. Do not cut through the notch.

NOTE:

The uncut wood between the felling and notch cuts is called the hinge. The hinge controls the fall of the tree and should be of uniform thick ness.

6. As the saw nears the back cut, watch the treetop and the cut for signs of movement. Be alert as soon as the tree starts to move, turn off the saw, pull it from the tree and move away quickly on your escape route.

7. For trees larger than bar length, make two felling cuts. Cut in as far as the bar will go, move to the other side and start the second cut in the same manner as the first while pivoting the saw to complete the felling cut.

BUCKING

Bucking is the sawing of a log or fallen tree into smaller pieces.

1. Observe all safety precautions.

2. Use both hands. Grip the saw firmly.

3. Stand uphill. A log that is cut loose may role downhill.

4. Keep the chain out of the dirt. Dirt will dull the chain.

A dull chain is unsafe.

5. Stand to the left of the saw.

CROSSCUTTING

NOTE:

Before starting to cut through a log try to imagine what is going to happen. Look out for stresses in the log and cut through the log in such a manner that the guide bar will not get pinched.


OPERATION

LOGS WITH PRESSURE ON TOP (FIGURE

3)


2. Begin with an upper cut, down from the top. Do not cut too deeply. A cut of about 1/3 of the log diameter is enough.

3. Finish with a bottom cut. They should meet.

Figure 3. Crosscutting Logs with Pressure on Top

THICK LOGS LARGER THAN BAR LENGTH

WITH PRESSURE ON TOP (FIGURE 4)


2. Begin by cutting on the opposite side of the log.

3. Pull the saw towards you and cut from the top.

4. Cut from the bottom. Make a boring cut if the log is close to the ground.

5. Finish with a bottom cut.

Figure 4. Crosscutting Logs Larger than Bar Length

With Pressure on Top


OPERATION

LOGS/LIMBS WITH PRESSURE ON

BOTTOM (FIGURE 5)


2. Begin with a bottom cut. The depth of the cut should be about 1/3 of the log diameter.

3. Finish with an upper cut, down from the top. The saw cuts should meet.

Figure 5. Crosscutting Logs/Limbs with

Pressure on Bottom.

THICK LOGS LARGER THAN BAR

LENGTH WITH PRESSURE ON THE

BOTTOM (FIGURE 6)


2. Begin by cutting on the opposite side of the log.

3. Pull the saw towards you and cut from the top.

4. Cut from the bottom. Make a boring cut if the log is close to the ground.

5. Finish with a top cut.

Figure 6. Crosscutting Thick Logs with Pressure on

Bottom


OPERATION

PRUNING AND DEBRANCHING


2. Use both hands. Keep a firm grip.

3. Be alert for kickback. Do not allow the tip of the bar to touch anything while the chain is in motion.

4. Do not cut overhead. Keep the saw below chest level. The chain is too close to your face in this position.

COLD WEATHER OPERATION

If the saw is to used during cold weather, preheat the hydraulic fluid at low engine speed. When using the normally recommended oils, oil should be at or above

50 °F/10 °C (400 ssu/ 82 centistokes) before use.

Damage to the hydraulic system or saw can result from use with fluid that is too viscous or thick.

Cutting frozen wood causes the cutters to wear, crack and break at the back rivet hole unless proper precautions are taken. To extend chain life when cutting in cold weather:

1. Be sure the oiler is working.

2. Keep the chain tensioned and check often.

3. Keep the cutters properly sharpened. Touch up at least every hour. Never force a dull chain to cut.

4. Clean out the bar groove and keep the oil hole open.

Turn the bar over to equalize wear on the rails.

5. Always install a new sprocket with a new chain.


TOOL PROTECTION & CARE

NOTICE

In addition to the Safety Precautions found in this manual, observe the following for equipment protection and care.

• Make sure all couplers are wiped clean before connection.

• The hydraulic circuit control valve must be in the

“OFF” position when coupling or uncoupling hydraulic tools. Failure to do so may result in damage to the quick couplers and cause overheating of the hydraulic system.

• Always store the tool in a clean dry space, safe from damage or pilferage.

• Make sure the circuit PRESSURE hose (with male quick disconnect) is connected to the “IN” port. The circuit RETURN hose (with female quick disconnect) is connected to the opposite port. Do not reverse circuit flow. This can cause damage to internal seals.

• Always replace hoses, couplings and other parts with replacement parts recommended by Stanley

Hydraulic Tools. Supply hoses must have a minimum working pressure rating of 2500 psi/172 bar.

• Do not exceed the rated flow (see Specifications) page in this manual for correct flow rate and model number. Rapid failure of the internal seals may result.

• Always keep critical tool markings, such as warning stickers and tags legible.

• Tool repair should be performed by experienced personnel only.

• Make certain that the recommended relief valves are installed in the pressure side of the system.

• Do not use the tool for applications for which it was not intended.


TROUBLESHOOTING

If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the saw, always make sure the hydraulic power source is supplying the correct hydraulic flow and pressure to the saw as listed in the table. Use a flowmeter known to be accurate. Check the flow with the hydraulic fluid temperature at least 80 °F/27 °C.

Cuts slow.

PROBLEM

Bar turns color.

Tool does not run.

Tool runs backwards.

On/Off trigger is hard to press.

Oil leakage around drive sprocket.

CAUSE

Insufficient fluid flow or low relief valve setting.

Chain dull.

Backpressure too high.

Insufficient oiler flow.

Power unit not functioning.

Coupler or hoses blocked.

Mechanical failure.

Pressure and return reversed.

Pressure and return reversed.

Backpressure too high.

Motor shaft seal failure.

REMEDY

Adjust fluid flow to proper gpm. For optimum performance adjust relief valve to 2250 psi/155 psi.

Sharpen per instructions or replace.

Should not exceed 250 psi/17 bar at

8 gpm/30 lpm measured at the end of the tool operating hoses.

Adjust oiler per Service Manual.

Check power unit for proper flow and pressure (4 gpm/15 lpm at 1500 psi/104 bar minimum for the CS05 and 7 gpm/26 lpm at 1000 psi/70 bar for the CS06).

Remove obstruction.

Disassemble tool and inspect for damage.

Connect for proper flow direction.

Motor shaft rotates clockwise.

Correct for proper flow direction.

Should not exceed 250 psi/17 bar at

8 gpm/30 lpm measured at the end of the tool operating hoses.

Replace as required. Make sure that oil present is not the result of excess oiler flow.

Replace as required.

Oil leakage between rear gear housing and valve handle assembly.

Chain continues to move after valve is shut off.

Motor face seal failure.

Chain is too loose.

Input flow too high.

Tighten chain.

Decrease flow.


SPECIFICATIONS

Capacity

CS05 ..................................................................................................... 12 and 15 inch/30 and 38 cm Cut Lengths

CS06 ......................................................................................... 12, 15 and 20 inch/30, 38 and 51 cm Cut Lengths

Weight (w/o bar) ...................................................................................................................................6.25 lbs/2.8 kg

Length (w/o bar) ................................................................................................................................14 inches/36 cm

Width ...................................................................................................................................................9 inches/23 cm

Pressure

CS05 .............................................................................................................................1500-2000 psi/105-140 bar

CS06 ................................................................................................................................ 1000-2000 psi/26-34 lpm

Optimum Flow

CS05 .................................................................................................................................................. 5 gpm/19 lpm

CS06 .................................................................................................................................................. 8 gpm/30 lpm

Porting ....................................................................................................................................................8 SAE O-ring

Connect Size and Type ....................................................................................................3/8 inch NPT Male Adapter

Hose Whips ............................................................................................................................................................ No

Motor ...............................................................................................................................................................Integral

Kickback Reduction Features

....................Low Kickback Saw Chain, Small Radius Saw Bar, Front Hand Guard, Low Inertia Motor/Drive System

Sound Power Level ....................................................................................................................................... 107 dBA

Sound Pressure Level @ 1 meter ................................................................................................................ 93.1 dBA

Vibration Level ..............................................................................................................................................3.1 (m/s

2

)

ACCESSORIES

Rim Sprocket, .325 P × 7 Tooth .........................................................................................................................07629

12-inch Saw Bar ................................................................................................................................................08347

15-inch Saw Bar ................................................................................................................................................07638

20-inch Saw Bar ................................................................................................................................................07639

Saw Chain for 12-inch Bar.................................................................................................................................08348



File Guide with File ............................................................................................................................................12363

Flat File .............................................................................................................................................................. 11294

Scrench ............................................................................................................................................................. 11464

SERVICE TOOLS

O-ring Tool Kit ....................................................................................................................................................04337

Seal Kit ..............................................................................................................................................................07830


CS05/CS06 PARTS ILLUSTRATION


25

26

27

28

12

13

14

20

21

22

23

24

7

8

9

5

6

ITEM

NO.

1

2

3

4

10

11

15

16

17

18

19

29

30

31

32

06971

07724

1

07620

07714

1

11354 1

1 07632

07723

00144

00230

1

01116 1

02649 2

07611 1

02634 3

PART

NO.

00753

09622

07636

08202

1

28323 1

QTY DESCRIPTION

8 CAPSCREW

CAPSCREW U/W MODEL

NAME TAG—CS06

NAME TAG—CS05

CE DECAL (CE ONLY)

07652 1

07834 1

00289 2

04041 4

00020 1

07612 1

04106

07832

—

2

—

00038

00788

1

01362 1

02921 1

17784 1

REAR GEAR HSG ASSY (7–9 GPM)

REAR GEAR HSG ASSY (4–6 GPM)

DOWEL PIN

BUSHING

O-RING

IDLER SHAFT

DRIVE GEAR (7–9 GPM)

DRIVE GEAR (4–6 GPM)

NO ITEM

00429

09277

1

07473 1

13907 1

12412 1

28409 1

NUT

NUT U/W MODEL

O-RING

AUTOMATIC OILER

SOUND POWER LEVEL. DECAL

(CE ONLY)

LOCKNUT

LOCKNUT U/W MODEL

BAR ADJUSTMENT NUT

BAR ADJUSTMENT NUT U/W MODEL

OC/CC DECAL (NOT ILLUSTRATED)

SCREW

SCREW U/W MODEL

CAPSCREW

CAPSCREW U/W MODEL

BUCKING CLEAT

HANDLE BAR RETAINER

HANDLE BAR

WASHER

NUT

NUT U/W MODEL

HAND GUARD

07628

02446

3

66577 1

08347 1

07638 1

07639 1

08348 1

07641 1

07642 1

WARNING DECAL (KICKBACK)

WARNING DECAL (ELECTRIC)

COMPOSITE SAFETY DECAL (CE

ONLY)

CAPSCREW

CAPSCREW U/W MODEL

CHAIN GUIDE PLATE-INSIDE

SAW BAR 12 IN.

SAW BAR 15 IN.

SAW BAR 20 IN.

SAW CHAIN – 12 IN.




CS05/CS06 PARTS LIST

67

68

69

70

59

60

61

62

63

64

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

52

53

54

55

56

ITEM

NO.

33

34

35

36

57

58

65

66

34093 1

03972 1

03973 1

28234 2

01605 2

07693

07713

1

07624

07718

03009

03278

1

2

11207 1

10535 1

07626 1

07609 2

07613

07710

1

16070 1

10536 1

00026 1

07627 1

00072

00875

1

07603 1

07602

07715

1

PART

NO.

QTY DESCRIPTION

66578 1 CHAIN GUIDE PLATE-OUTSIDE

07618 1

07631

07722

2

CHAIN GUARD

NUT

NUT U/W MODEL

00453

00808

1

07617 1

07629

07616

06635 1

00335

07720

1

04746

04539

1

1

1

1

NUT

NUT U/W MODEL

WASHER

RIM SPROCKET

SPROCKET ADAPTER

RET RING

BALL BEARING

BALL BEARING U/W MODEL

AUTOMATIC OILER DECAL

WASHER

07623 1

07630 2

02688

02764

1

04037 1

07615 1

04856 1

04044 2

CHAIN CATCHER

STUD

CAPSCREW

CAPSCREW U/W MODEL

SHAFT SEAL

SEAL BACK-UP WASHER

RETAINING RING

NEEDLE ROLLER

DRIVE SHAFT

DRIVE SHAFT U/W MODEL

RETAINING RING

SELECTOR SCREW

O-RING

O-RING

ROLL PIN

ROLL PIN U/W MODEL

SAFETY CATCH

SPRING

SPRING U/W MODEL

TRIGGER CASTING

COUPLER, FEMALE

COUPLER, MALE

HOSE

O-RING

VALVE HANDLE ASSY

VALVE HANDLE ASSY U/W MODEL

ROLL PIN

ROLL PIN U/W MODEL

ROLL PIN

ROLL PIN U/W MODEL

CIRCUIT TYPE D DECAL (CE ONLY)

ON/OFF VALVE SPOOL

O-RING

SPRING WASHER

CS05/CS06 PARTS LIST

ITEM

NO.

71

72

73

74

75

76

77

PART

NO.

QTY DESCRIPTION

07610 1 SPRING

00190 1

10537 1

ROLL PIN

KEEPER

07625 1

03786 1

03782 1

05144 1

PLUG BUTTON

GPM STICKER (7–9 GPM)

GPM STICKER (4–6 GPM)

BAR & CHAIN GUARD

00767 1

00936 2

26414 1

03971 1

GREASE FITTING U/W MODEL ONLY

ADAPTER (NOT SHOWN)

LOCK OUT KIT, SHIPPED INSTALLED

(NOT SHOWN)

COUPLER SET

07830 1 SEAL KIT


UNDERWATER TOOLS DEPTH GUIDELINE

UNDERWATER MODELS ONLY

CAUTION

DO NOT USE HYDRAULIC TOOLS UNDER-

WATER THAT ARE NOT DESIGNATED AS

AN “UNDERWATER” MODEL, OR THIS

WILL RESULT IN DAMAGE TO THE TOOL.

For underwater hydraulic tools the applications are broken down into four quadrants depending on type of tool and method of operation.

Operation Overview

Percussive

Tools: Breakers,

Hammer Drills and

Chipping Hammers

Max Depth: 500' limitations due to accumulator PSI max (increase 40

PSI for every 100')

Rotational

Tools: Grinders,

Saws, Chain Saws

Max Depth: 1000' -

Reference hose sizing guide below

Tools: Breakers,

Hammer Drills and

Chipping Hammers

Tools: Grinders,

Saws, Chain Saws

The types of tools are percussive and rotational, each with different characteristics allowing for different depth operation. With percussive tools, the nitrogen accumulator PSI must counter the increase in ambient pressure found at lower depths.

Since there is a maximum PSI for percussive tools they are limited to certain depths. Rotational tools do not have accumulators and thus capable of deeper depths.

Max Depth: 500' limitations due to accumulator PSI max (increase 40

PSI for every 100')

Max Depth: 1000' -

Reference hose sizing guide below

The methods are broken into diver operated or remote operated vehicle (ROV). ROV's can reach lower depths and with an on-board hydraulic power source that is depth compensated, can operate hydraulic tools at depths of thousands of feet. ROV operation is still limited to the tool, for example a percussive tool has the same depth limitation whether ROV or diver operated.

Recommended Hose Diameters

Depth (ft)

100

300

600

1000

8 GPM

5/8”

3/4”

1”

1”

12 GPM

5/8”

1”

1”

1-1/4”

24 ► CS05/06 User Manual

NOTES

CS05/06 User Manual ◄ 25

Stanley Hydraulic Tools

3810 SE Naef Road

Milwaukie, Oregon 97267-5698 USA

(503) 659-5660 / Fax (503) 652-1780 www.stanleyhydraulics.com

No results