ANTUMBRA
DIST
BUILDING INSTRUCTIONS
PCB V1.1
01. BUILD NOTES
Before you start building look through the build manual so that you’ll be familiar with the building process and you won’t run into any surprises!
102
472
102
00 01 02 03 04
02. BUILD
00. Orient the PCB as seen on the left
01. Solder the TL071 in place
(oriented to the top)
02. Solder the single 1n5819 diode
Look out for their orientation!
03. Solder the single 1k resistor
04. Solder the single 4.7k resistor
102
105
105 105
105
105
105
103
103
105
105
105
105
103
103
105
105
105
105
103
103
105
105
105
105
103
103
105
105
472
105
472
105
472
105
472
105
472
105
02. BUILD
05. Solder the five 1M resistors
06. Solder the two 10k resistors
07. Solder the single 10pF capacitor
08. Solder the single 47nF capacitor
09. Solder the three 1nF capacitors
102 102 102 102
05 06 07 08 09
102
105
105
103
103
105
105
105
105
103
103
105
105
105
105
103
103
105
105
105
105
103
103
105
105
105
105
103
103
105
105
472
105
472
105
472
105
472
105
472
105
10
102
11
102
12
102
13
102
14
02. BUILD
10. Solder the single 10nF capacitor
11. Solder the single 100nF capacitor
12. Solder the two 1uF electrolytic capacitors
Look out for their orientation! Their shape has to match up with the silkscreen.
13. Solder the single 10uF electrolytic capacitor
14. Solder the two diodes for mode A.
The type of these diodes are optional, you can use whatever SMD/TH diodes (even LEDs) you want, they all have different flavors, recommended is the 1n270 germanium diodes. (Experimenting is encouraged)
Look out for their orientation!
105
105
103
103
105
105
102
472
105
15 16 17 18 19
02. BUILD
15. Solder the two diodes for mode B.
The type of these diodes are optional, you can use whatever SMD/TH diodes (even LEDs) you want, they all have different flavors, recommended is the 1n4148 diodes. (Experimenting is encouraged)
Look out for their orientation!
16. Flip the board!
17. Solder the 2x5 pin power header
18. Solder the 1x3 pin header for the jack lights switch
19. Solder the two SMD LEDs
Look out for their orientation! The marking should be as on the illustration.
102
105
105
103
103
105
105
105
105
103
103
105
105
105
105
103
103
105
105
105
105
103
103
105
105
105
105
103
103
105
105
472
105
472
105
472
105
472
105
472
105
02. BUILD
20. Flip the board back!
DO NOT SOLDER YET!
21. Place the two jacks
22. Place the two switches
23. Place the A100k pot
24. Place the A1M pot
102 102 102 102
20 21 22 23 24
105
105
103
103
105
105
102
472
105
25
02. BUILD ű
25. Place the A10k pot
Now put on the front panel and tighten the nuts on the jacks and pots. Align them in the holes as you like. Solder!
You are done with building! Congratulations!
DIST is designed by David Szebenyi under Antumbra.
It is based on the MXR Distortion+ / Hexinverter
Batteryacid v1.0
www.antumbra.eu
Manual by David Szebenyi ( www.aman.hu
)
2018 • All rights reserved!
